Honeywell PMD系统的安装

气体水平管道安装简图
≤120°
水平线 A-A
注意：探针安装时使总压口对准来流方向，并位于管道中央，探针表体处于一个管道上方。
气体在水平管道安装简图
图 6 测量煤气、空气等气体流量的安装参考图
7
来流方向
前直管段最小10倍管径
后直管段最小5倍管径
A
A
液体水平管道安装简图
水平线
≤
A-A
注意：探针安装时使总压口对准来流方向，并位于管道中央，探针表体处于一个管道下方。
10
主要工作性能参数: 量程范围： （1）0～100 KPa(最小可调到 0～2.5 KPa) （2）0～2.5 KPa(最小可调到 0～100 Pa) 最大工作压力：14 MPa 输出电流：4～20 mADC 工作温度：-40～85℃ 线性度：0.075 % 时间漂移：0.03%/a
零点和量程校核方法：（以 0～10 Kpa 为例） 1)打开有 Z 和 S 标志的面板，Z 代表零点（ZERO），S 代表量程（SPAN）； 2)参考压力为 0 Kpa 时，按动+Z 和-Z 钮，调到输出为 4mA； 3)参考压力为 10 Kpa 时，按动+S 和-S 钮，调到输出为 20mA。
24VDC
+_
接线端子
3
2
1
4
+
积算仪
_
图 8 压力变送器接线端子布置示意图
四、 Honeywell STD924 型差压变送器使用说明
STD924 型差压变送器系世界上著名的自动化仪表生产厂家美国霍尼韦尔公司 的产品，具有高精度、宽量程比、宽迁移率、宽域温度静压补高安全、可靠性、 高稳定，重复性、完善的自诊断功能等优点，各方面性能优越。

Honeywell CameraInstallation Guide6S S L.L.C.B r y a n t A v e N-B r o o k l y n P a r k-M N55444U S AT e l:+1-651-233-0977E-m a i l:i n f o@6s s.c oW e b:w w w.6s s.c oD e c e m b e r2019T ABLE OF C ONTENTS1.I NTRODUCTION (4)2.G ETTING S TARTED (5)2.1.System Requirements (5)2.2.System Introduction (5)3.I NSTALLATION OF O NVIF D EVICE M ANAGER (6)3.1.Onvif Device Manager Setup (6)3.2.Starting Onvif Device Manager (8)4.H ONEYWELL I NTEGRATION WITH M ILESTONE (10)4.1.Setup Wizard (10)4.2.Management Client Interface (12)4.3.Smart Client Interface (14)T ABLE OF F IGURESFigure 1: 6SS LPR Edge base Architecture (5)Figure 2: Run wizard (6)Figure 3: Missing .NET Framework (6)Figure 4: Onvif Device Manager Setup (7)Figure 5: Destination folder (7)Figure 6: Installation Button (8)Figure 7: Windows Firewall alert (8)Figure 8: Onvif device list (9)Figure 9: LPR Plugin Setup Folder (10)Figure 10: LPR Setup Wizard (10)Figure 11: 6SS LPR Client Installation Folder (11)Figure 12: 6SS LPR Client Installation Setup (11)Figure 13: Honeywell LPR- SQL Server (12)Figure 14: Honeywell LPR- Camera Settings (12)Figure 15: Honeywell LPR- License Settings (13)Figure 16: Honeywell LPR- Alerts Settings (13)Figure 17: Milestone Live Interface (14)Figure 18: Milestone Alarm Interface (14)Figure 19: Milestone Honeywell LPR Interface (15)1.I NTRODUCTIONThis document is intended to provide a full installation guide of Honeywell Camera and its integration with Milestone XProtect.For this purpose, Onvif Device Manager (ODM) is installed and used as a tool to read all the detected events from Honeywell camera, save them into SQL database, and in turn pushing these metadata into Milestone Smart Client.Honeywell LPR Main Features•On-board ANPR camera•Fully integrated with all Milestone XProtect versions•View Live Detection from the Camera•Filter through LPR history based on various criteria•One click data Excel/PDF Export•Alarm Hotlist capabilities•Auto data retention period handling2.G ETTING S TARTED2.1.System Requirements•Windows OS 8 or above•SQL Server 2012 or above•Onvif Device Manager v2.2.250 or above•Milestone XProtect Management Client (2016 or above)•Milestone XProtect Smart Client (2016 or above)2.2.System IntroductionThe server part of the system consists of 2 main components: Management and LPR servers. Each LPR system contains only one Management se rver, and one or more LPR servers, depending on the project size and the system’s distributed architecture. Both processes can be installed and ran on the same server, but each with its own configuration. The machine has to be licensed first before doing anything on the LPR system after the installation. Below is a figure describing the architecture of the system.1.On-Board ANPR Cameras multi-streaming to LPR server and recording servers.2.The streaming videos will flow to the recording server.3.The LPR server will communicate with the On-Board ANPR cameras to retrievethe recognized data, then will parse this upcoming data to the SQL server.4.Store results in SQL or any other database, and trigger alarms if any.5.Send results and display on Smart Client.F IGURE 1:6SS LPR E DGE BASE A RCHITECTURE3.I NSTALLATION OF O NVIF D EVICE M ANAGER3.1.Onvif Device Manager SetupDownload onvifdm.msi setup-file using the following link (/projects/onvifdm/).Right-click odm-v2.2.250 → Click Insta ll → Run onvifdm.msi.F IGURE 2:R UN WIZARDSetup Wizard will check if Microsoft .NET Framework 4 is installed o n the computer, if not click “Yes” to install it.F IGURE 3:M ISSING .NET F RAMEWORKWindows User Account Control may ask for permission, click yes to continue with the installation.F IGURE 4:O NVIF D EVICE M ANAGER S ETUPChoose the destination folder and click Next, then choose Install to start the installation.F IGURE 5:D ESTINATION FOLDERF IGURE 6:I NSTALLATION B UTTONTo complete the ONVIF Device Manager Installation process,3.2.Starting Onvif Device ManagerLaunch ONVIF Device Manager from the desktop or via the Start menu.During the first launch, Windows Firewall may ask for permission to open access to the network for onvifdm.exe as shown in Figure 7, click “Allow access”.F IGURE 7:W INDOWS F IREWALL ALERTAfter ONVIF Device Manager has been launched, the Honeywell camera is automatically detected and displayed in the device list on the left. If the device has not been detected automatically, check the connection and click Refresh as shown in Figure 8.F IGURE 8:O NVIF DEVICE LIST4.H ONEYWELL I NTEGRATION WITH M ILESTONE4.1.Setup WizardUnzip the Release folder and open to run the setup wizard for the LPR plugin.F IGURE 9:LPR P LUGIN S ETUP F OLDERF IGURE 10:LPR S ETUP W IZARDChoose the path to where the LPR plugin folder will be created as shown in Figure 11. Click next to continue and the setup will be installed as shown in Figure 12.F IGURE 11:6SS LPR C LIENT I NSTALLATION F OLDERF IGURE 12:6SS LPR C LIENT I NSTALLATION S ETUP4.2.Management Client InterfaceOpen Milestone XProtect Management Client then click “HONEYWELL LPR” under MIP Plugins as shown in Figure 13.Error! Reference source not found.In the first tab enter the server name or IP address in case the SQL Server is installed on a different device otherwise you can keep it blank (local host).F IGURE 13:H ONEYWELL LPR-SQL S ERVERThen, you need to specify Honeywell camera settings for first time use by entering the camera IP address and port number, click “Set Connection Info” to save your settings.F IGURE 14:H ONEYWELL LPR-C AMERA S ETTINGSAs for the LPR license, click “Get Computer ID” button and send to *********** the issued product ID with the number of licenses needed to activate the LPR. Upon receiving the license file, click “Import License” button to import the latter.Note that for each camera used a license is required. The license is paid once with no expired date, with a yearly optional upgrade (18 % of the license fee for each camera) for any additional features, maintenance, and enhanced versions.F IGURE 15:H ONEYWELL LPR-L ICENSE S ETTINGSThe last tab is for alerts. Here you can specify the plate number you want to fire an alarm for when detected by the camera, either as a blacklisted or whitelisted. You can also attach an event for this alarm in order to trigger a certain action. Use the button “Add Alert” to activate the alarm.F IGURE 16:H ONEYWELL LPR-A LERTS S ETTINGS4.3.Smart Client InterfaceOpen Milestone XProtect Smart Client. In the live tab select your intended camera as shown in the bottom right corner of Figure 17.When the camera detects license plate number, the latter will be shown as a snapshot of the plate number in the right panel above the button “Select Camera”.F IGURE 17:M ILESTONE L IVE I NTERFACEAll the alerts previously defined in the management client are shown in the “Alarm Manager” tab with a red flag indicating the number of alarms fired as shown in Figure 18. If you click on a certain alarm the live and recording videos will be shown a long with the alarm’s information.F IGURE 18:M ILESTONE A LARM I NTERFACEIn the “Honeywell LPR” tab you can check all the LPR events captured by which camera, in which category and country, at what confidence level detected at a certain date along with the plate number and its image. You can use the filters shown in the right panel of Figure 19 as well as to export the listed events to excel file.When you click on an event line you can use the bottom right video to play back the video frame from the first moment the plate number is captured.F IGURE 19:M ILESTONE H ONEYWELL LPR I NTERFACE。

HSIM (HouseLogix Security Integration Module)Installation Instructions V1.01 - 20131202TOOLS REQUIRED:∙Small flat head screw driver∙Standard #22 gauge solid core alarm wire is recommendedINSTALLATION:1.Security panel prerequisite programming (not required for DSC or older Vista SE panels)a.If you are unfamiliar with programming the security system panel, please refer to the programmersguide or contact your security professional.b.Since the HSIM functions as a keypad, a new address in the security panel must be programmed beforeconnecting. Here is a list of Honeywell devices that require an address to function. Be sure none of theseother devices overlap or share an address:i.Keypadsii.RF Expanders (Wireless)iii.Output Devices - Relaysiv.Long Range Radio - Ethernet or GSM devicesv.AUI - Advances User Interfacevi.Honeywell RIS - Remote Interactive Service - Total Connectc.To add the adapter, enter into programming mode using the installer code. EG: If your installer code is1234, you would enter 1234800. DO NOT overlap addresses with any of the devices listed above. It isrecommended you use the following settings for the HSIM keypad address:i.Device Address: varies, do NOT overlap with existing devicesii.DeviceType: 01 - Alpha Keypadiii.Sound Option: 0iv.Keypad Global: 0v.AUI: 0d.Write the assigned address below:_______________________________________________________________________________2.Physical Connectiona.It is recommended you contact the monitoring company and put the system in test mode. Oncecompleted, disconnect the power adapter and backup battery from the alarm system.b.Begin by connecting the security wire to the alarm panel keypad bus following the standard color andwiring scheme:HONEYWELL/ADEMCO DSC-Power (-): Black-Power (-): Black-Power (+): Red-Power (+): Red-DI: Green-DI: Yellow-DO: Yellow-DO: Greenc.Remove the top cover of the module. There you will find a 4 screw terminal block with the associatedDO, DI, 12V, and GND labels.d.Connect the other end of the security wire to the integration module following the same color scheme.Tighten the terminal blocks and verify the wires are secure.e.Return power to the alarm panel and connect the battery backup. When power is connected the integration module should have a blinking green LED indicating the unit is receiving messages from the panel.f.Attach the top half of the module’s cover and plugdirectly into your controller.3.Control4 Programminga.Once the security panel programming and physical connection has been made, open Composer Pro andconnect to the local project.b.Add the integration module driver to the project. It can be found under:i.Search - “Local Database”ii.Device Type –“Security System”iii.Manufacturer –“HouseLogix, Inc.” –“HouseLogix Security Integration M odule”c.Once the driver has been added to the project, switch to the “Connections” tab and bind the RS232 portto the matching Control4 interface.d.Switch back to the “System Design” tab. The driver will read the current adapter settings and update theProperties tab.e.At this point you can modify any of the settings below:i.Keypad Address: Integer1.When using Honeywell, this should be changed to the address written down above thatwas programmed into the alarm panel. Default HSIM address is 18.ii.Number of Zones: Integer1.Input the highest number zone you would like to monitor, even if they aren't all used.EG: If you have zones 1,2,3,4,5, 25,26,27,28 and 29 hooked up, you would input 29.Pressing Set will generate those zones so you can connect them to generic sensors inthe Connections tab.iii.Number of Relays: Integer1.Input the total number of relays to activate on the security panel. The driver supports atotal of 16 relays, however, you must program the relay board(s) to start at address 12.Only relay status is available, not control.iv.Watchdog Timer: Enabled or Disabled.1.If Enabled, after the allotted time in the Watchdog Timer Length property expires, it willtoggle the WatchdogFailure variable (set to true) under the Security System driver in theProgramming tab. This is helpful for determining if the security panel has lostcommunication with the controller.v.Watchdog Timer Length: Integer1.The amount of time (in minutes) before the WatchdogFailure variable is tripped inprogramming. The lower the setting, the higher potential use of resources on thecontroller.vi.Debug Mode:ed for debugging the driver. Output is displayed on the Lua tab.vii.Connection Status:1.Shows the current connection status of the HSIM.viii.Mode:1.Allows the HSIM to be converted from Honeywell to DSC control.ix.Zone Name Replacement:1.Allows the ZNR to be enabled or disabled.2.ZNR allows a security panel that is not programmed with Zone Names to accuratelyshow the appropriate zone name on the navigator or interface.x.ZNR - Zone Number:ed to set the zone number for naming the appropriate zones.xi.ZNR – Zone Name:ed to set the zone name for each zone.f.If you would like to monitor any zones or relays, add the generic sensors or relays to the project in the“System Design” tab and then connect each to the corresponding Zone number in the “Connections”tab.g.Refreshing the Navigators (Shift + F5) should now show the security system keypad under the Securityicon and any connected sensors will show their status under Motorization and Sensors.LICENSE AGREEMENTThis license governs use of the accompanying firmware. If you use the device, you accept this license. If you do not accept the license, do not use the device. The embedded devices firmware ("Software") is licensed, not sold, to you by Nu Tech Software Solutions, Inc. ("NuTech Software Solutions") for use only under the terms of this License, and Nu Tech Software Solutions reserves any rights not expressly granted to you. You own the device on which the Software is stored, but Nu Tech Software Solutions, its licensors and sub-licensors retain ownership of the Software itself.1. DefinitionsThe terms "reproduce," "reproduction" and "distribution" have the same meaning here as under U.S. copyright law. "You" means the licensee of the software. "Your company" means the company you worked for when you downloaded the software. "Reference use" means use of the software by you or within your company as a reference, for the sole purposes of developing your product, debugging your products, maintaining your products, or enhancing the interoperability of your products with the software, and specifically excludes the right to distribute the software outside of your company or to any third party.2. Grant of Rights(A) Copyright Grant- Subject to the following terms and conditi ons, Nu Tech Software Solutions grants to the end user (“You”) a non-exclusive, non-transferable, fully paid and royalty-free license, without the right of sublicense, to use the Product solely in the form of the binary firmware image provided, only to the extent necessary to use the hardware. Notwithstanding the foregoing, this License does not apply to the source code or object code of the Product. This license is not a sale. You may not rent, lease, or lend the Product. Nu Tech Software Solutions may cancel this LICENSE if you do not abide by its terms and conditions. This LICENSE applies to updates or supplements to the original Product, unless we provide other terms along with the update or supplement.RESERVATION OF RIGHTS. Nu Tech Software Solutions reserves all rights not expressly granted to you in this LICENSE. Title and copyrights to the Product remain with Nu Tech Software Solutions.3. Limitations(A) No Trademark License- This license does not grant you any rights to use the Licensor’s name, log o, or trademarks.(B) If you begin patent litigation against the Licensor over patents that you think may apply to the software (including a cross-claim or counterclaim in a lawsuit), your license to the software ends automatically.(C) LIMITATION ON REVERSE ENGINEERING, DECOMPILATION, AND DISASSEMBLY. You may not reverse engineer, decompile, or disassemble the Product. You may not copy the Product or transfer it to other devices without the express prior written consent of Nu Tech Software. Notwithstanding any prior agreement you may have with Nu Tech Software.(D) The software is licensed "as-is." You bear the risk of using it. In no event will Nu Tech Software Solutions, its parent or subsidiaries or any of the licensors or sub-licensors, directors, officers, employees or affiliates of any of the foregoing be liable to you for any consequential, incidental, indirect or special damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information and the like), whether foreseeable or or unforeseeable, arising out of the use of or inability to use the Software or accompanying written materials, regardless of the basis of the claim and even if Nu Tech Software Solutions or a Nu Tech Software Solutions representative has been advised of the possibility of such damage. Nu Tech Software Solutions' liability to you for direct damages for any cause whatsoever, and regardless of the form of the action, will be limited to replacement of the Software that caused the damages. THE LIMITATION WILL NOT APPLY INCASE OF PERSONAL INJURY ONLY WHERE AND TO THE EXTENT THAT APPLICABLE LAW REQUIRES SUCHLIABILITY. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.4. General(A) This License will be construed under the laws of the State of Oregon. If any provision of this License shall be held by a court of competent jurisdiction to be contrary to law, that provision will be enforced to the maximum extent permissible, and the remaining provisions of this License will remain in full force and effect. If you are a U.S. Government user, then the Software is provided with " RESTRICTED RIGHTS" as set forth in subparagraphs (c) (1) and (2) of the Commercial Computer Software-Restricted Rights clause at FAR 52.227-19 or subparagraph (c)(1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.277-7013, as applicable. Manufacturer: Nu Tech Software Solutions, 11575 SW Pacific HWY, Suite 109, Tigard, Oregon 972235. Termination(A) This License is effective until terminated. This License will terminate immediately without notice from Nu Tech Software Solutions or judicial resolution if you fail to comply with any provision of this license. Upon such termination you must destroy the Software, all accompanying written materials and all copies thereof, and Sections 3, and 4 will survive any termination.。

六个12v充电式镍氢电池16个用户代码13个辅助密码个紧急功能通信ademcolowspeedsescoaradionicsademcoexpressademcocontactid设置设定的选项存储在eerom可经由ibm兼容计算机通过compassdownloader软件和特hayes调制解调器进行更新下载或控制语音提示设置模式其它功能退出错误功能检测实际警报与在退出延时结束后再出门而造成的退出报警之间的区别事件记录最多可存储84件事件rf阻塞检测兼容加密设备高安全性警报输出压电轰鸣器最大30ma闹铃输出最大120ma针对盗窃紧急情况的连续输出针对火警的间歇式脉冲输出远程无线电报警声音通知特殊功能lynxriench免提操作系统硬件安装22安装控制器221壁挂式安装下图显示了从底板上分离下来的主机前面板
4 系统操作 ................................................................................................................................. 42
4.1 安全密码 .......................................................................................................................... 42 4.2 紧急键.............................................................................................................................. 42 4.3 键盘功能 .......................................................................................................................... 43 4.4 报警声音通知（双向语音功能）...................................................................................... 44 4.5 “Follow Me”提示功能..................................................................................................... 45 4.6 “Follow Me”系统语音播放功能 ...................................................................................... 46 4.7 退出错误警报显示 ........................................................................................................... 46 4.8 故障情形 .......................................................................................................................... 46 4.9 测试模式 .......................................................................................................................... 47