1燃气轮机1.1种类和型式1.1.1燃气轮机gas turbine：将气体压缩、加热后在透平中膨胀，把其部分热能转换为机械能的旋转式动力机械。
一般由压气机、燃烧室、透平、控制系统及基本的辅助设备组成。
1.1.2燃气轮机动力装置gas turbine power plant：以燃气轮机为动力的成套装置。
它包括燃气轮机和产生有用的动力所需要的基本设备。
1.1.3开式循环燃气轮机open cycle gas turbine：热力循环的工质由大气中及入并排入大气的燃气轮机。
1.1.4闭式循环(燃)气轮机closed cycle gas turbine：热力循环的工质与大气隔离的(燃)气轮机。
1.1.5半闭式循环燃气轮机semi-closed cycle gas turbine：同一热力循环的工质，一部分进行闭式循环，另一部分进行开式循环的燃气轮机。
1.1.6简单循环燃气机imple cycle gas turbine：仅由压缩、一次加热和膨胀过程组成热力循环的燃气轮机。
1.1.7复杂循环燃气轮机complex cycle gas turbine：在循环中除压缩、一次加热和膨胀过程之外，还具有回热、中间冷却、再热三者中的一个或若干方式组合的燃气轮机。
1.1.8燃气-蒸汽(轮机)联合循环gas and steam(turbine)combined cycle：燃气轮机和汽轮机在热力过程中结合在一起的循环。
1.1.9单轴燃气轮机single-shaft gas turbine：压气机和透平的转子都机械地连接在一起的燃气轮机。
1.1.10多轴燃气轮机multi-shaft gas turbine：至少具有两根机械上独立的透平轴的燃气轮机。
1.1.11分轴燃气轮机spilt-shaft gas turbine：压气机透平和动力透平分别配置在彼此独立的轴上的一种多轴燃气轮机。
1.1.12箱装式燃气轮机packaged gas turbine：设计成便于运输和安装的箱装结构的燃气轮机。
【英语角】轮机英语词汇rotational speed：转速capacity: 功率steam turbine: 蒸汽轮机gas turbine: 燃气轮机speed reduction ratio: 减速比displacement: 排量flexible coupling: 柔性联轴节maintenance interval：检修周期gasoline engine：汽油机draft：吃水线torsional vibration damper: 减振器torque：扭矩prime mover：原动机be aligned with: 与…对中alignment：对中thermal efficiency：热效率loop scavenge：回流扫气cross scavenge：横流扫气uniflow scavenge：直流扫气supercharge：增压tappet clearance：挺杆间隙spark plug：火花塞indicator diagram：示功图indicator cards：示功图mechanical efficiency：机械效率compressed air: 压缩空气coolant：冷却剂occur：发生spray of fuel: 雾状燃油，油雾timing: 定时foul: 使…脏污fouling：污垢，脏污stuffing box：填料函，填料箱atmospheric pressure：大气压camshaft：凸轮轴cam：凸轮internal combustion engine：内燃机MIP（mean indicated pressure）：平均指示压力combustion chamber：燃烧室compression ratio：压缩比cylinder bore: 缸径overlap：重叠cross-head pin：十字头销bearing shell：轴瓦drill：钻孔，钻井，演习angle：角度expose：暴露，打开cycle：工作循环uncover：打开descending piston：下行的活塞value：值，数值decrease：降低，下降increase：上升，增加governor：调速器governor weight：调速器的飞重fuel injection：燃油喷射，喷油reliability：可靠性stroke coefficient：冲程系数give off：释放，放出naturally aspirated：自然吸气的，自然换气的admit：准许进入intake valve：进气阀linear motion：直线运动rotary motion：回转运动atomization：雾化cylinder firing pressure：气缸的爆炸压力be subjected to: 受到，遭受，承受ignition lag：滞燃期ignition delay period：滞燃期degree：程度，学位back pressure：背压thermal energy：热能mechanical energy: 机械能clockwise：顺时针地turbocharger：涡轮增压器brake horsepower：制动马力friction：摩擦single acting：单作用式的blow down：排气mixing：混合的mixture: 混合物advantage：优势，优点disadvantage：劣势，缺点compare：对比rocker arm：摇臂foundation：基础support：支撑，支持maintenance access：维修通道doors：道门in-line engine：直列式柴油机Vee engine：V型柴油机connecting rod large end bearing：连杆大端轴承connecting rod small end bearing：连杆小端轴承cast iron：铸铁cast steel：铸钢scavenging air box：扫气箱inertia：惯性thermal expansion：热膨胀aluminum：铝，铝的bronze：铜的mount：安装bolt：螺栓，用螺栓固定cross girder：横梁longitudinal girder：纵梁heat energy：热能float：漂浮，浮动piston skirt：活塞裙gudgeon pin：活塞销spur gear：正齿轮camshaft gear train：凸轮轴齿轮系starting air valve：空气启动阀side-chock bolt：侧楔形螺栓end-chock bolt：端楔形螺栓distance piece：调隙片compression plate：压缩片compression ratio：压缩比bearing housing：轴承座bearing cap：轴承盖bearing bush:轴瓦trunk piston：筒状活塞axial：轴向的stud：双头螺栓nut: 螺母enclose：密闭，密封guide：引导，导板tie rod=tie bolt=through bolt：贯穿螺栓entablature：机架column：机架cylinder block：气缸体external：外部的，外面的internal：内部的，里面的running-in period：磨合期load：负载，负荷，装载bearing wear：轴承磨损replace：替换，代替replacement：替换，代替clearance：间隙gap：间距tolerance：公差carrier ring：承磨环machine：机器，机械，加工machinery：机械（总称）machined：加工的，车削的ridge：凸台，凸肩groove：凹槽invariably：总是，一直forge：锻造forged：锻造的worn out：磨损的shim：垫片crank web：曲柄臂crank throw: 曲柄臂，曲拐crankpin：曲柄销crankcase：曲柄箱spring：弹簧，春天heat-resistant steel：耐热钢wearing resistance：抗磨，耐磨journal 轴颈sealing ring：密封环scraper ring：刮油环fuel valve：油头lubricator:注油器chromium-plated：镀铬的cylinder wall：汽缸壁lift out：吊出（活塞）piston ring belt: 活塞环区域cooling jacket：冷却水套balance：使…平衡shim：垫片thick：厚的thin：薄的thickness：厚度deformation：变形double bottom：双层底location：位置，定位locate：位于length: 长度width:宽度height：高度circular space：环形空间assemble：组装disassemble：拆卸assembly：组件fore and aft：前后semi-built：半组合式的transmit：传递，传送bending stress：弯曲应力torsion stress：扭曲应力shear stress：剪切应力turning gear：盘车机fitted bolt：拂配螺栓white metal：白合金horizontally：水平地be fitted with：装有，带有be provided with：装有，带有be equipped with装有，带有circumference [s?'k?mf?r?ns]: 圆周，周长nip：过盈压隙crush：过盈joint face：连接面，结合面diameter：直径oil distributor ring：布油环scraper ring：刮油环oil control ring：刮油环protective layer：保护层lining：衬有，内衬copper-lead alloy：铜铅合金aluminum-tin alloy：铝锡合金thin-walled：薄壁的flame hardened：淬火处理的shipchandler：船舶供应商bore：孔，镗孔thermal stress：热应力compressive stress：压应力forced lubrication system：强制润滑系统output：功率，输出cooling chamber：冷却腔crosshead shoes：十字头滑块slipper：滑块guide shoes：滑块dowel pin：定位销machine-turned：车削的projection：凸台vertical flange：垂直法兰coil spring：圈簧surface：表面slopping surface：倾斜表面sliding bearing：滑动轴承sludge：油渣main propulsion diesel engine：主推进柴油机tension：张力under tension：承受张力heater：加热器electric heater：电加热器timing gear：定时齿轮chain drives：链条驱动机构coincide with：重叠，一致center of gravity：重心statically balanced：静平衡wrist pin：活塞销heat conductivity：导热性oil film：油膜excess：过多的excessive：过多的，过大的rigid：结实的，坚实的transverse girder：横梁jack bolt：撑杆螺栓tap-bolt：锥头螺栓solid forged：整体锻造的solid bearing：整体式轴承polish：抛光telescopic pipe：伸缩管sag：下垂sagging：下沉量component：部件corrosion resistant：耐腐蚀的flame screen：防火网罩watertight compartment：水密舱taper：锥形的，逐渐减小的insert：插入：插件stationary part：固定部件statically balanced：静平衡dynamically balanced：动平衡turbulence：涡流flywheel：飞轮kinetic energy：动能fluctuation：波动valve stem：阀杆valve head：阀头valve cage：阀壳heat dissipation：散热water seal：水封wet liner：湿式缸套dry liner：干式缸套test cock：示功考克gasket：垫片knurling：滚花sodium：钠cold clearance：冷态间隙thrust：推力side thrust：侧推力manifold：总管bundle：管束overload：过载plasma coated：等离子涂层的oil sump：油底壳treat：处理，对待treatment：处理advanced firing：早燃retarded firing：后燃，发火滞后air venting arrangement：放气装置prime：灌注，注油priming：灌注priming pump：引液泵fuel supply passage：供油管路viscosity regulator：粘度调节器lifting check：起阀压力试验fuel main：总管plunger：柱塞spindle：针阀available：可用的，可得到的manoeuvring condition：机动操纵状态specification：规格grade:规格specific gravity：比重specify：规定service tank：日用柜day tank：日用柜port：港口，开口pressurize：加压injector nozzle：喷油嘴clog：堵塞particle：颗粒，颗粒状index：刻度，指数reading：读数rack：齿条rack and pinion arrangement：齿条/齿轮装置transfer pump：驳运泵bunker tank：燃油舱banker list：加油单have much to do with：与…..有很大的关系have nothing to do with：与…..没有关系quality：质量quantity：数量earlier ignition：发火提早stick open：保持开启状态oil sump：油底壳settling tank：沉淀柜droplet：水珠，油滴strainer：粗滤器fine filter：细滤器at interval：定期地prevent from doing sth.:防止做某事set：设定setting：设定量，设定值preset：预先设定buffer tank：缓冲柜balance tank：平衡柜（集油柜）service tank：日用柜cleared of：排除，清除barrel：套筒sleeve：套筒pipe：管子duct：管道，导管hose：软管flash point：闪点overflow：溢出（满了溢出）spill：溢油full ahead：全速前进fuel consumption：燃油消耗save：挽救，救生，节省economical speed：经济转速purify：分离，清洁purifier：分水机clarifier：分杂机foreign matter：杂质follower：滚轮calorific value：发热值pour point：倾点diameter：直径original：原来的，开始的vibration：振动penetration of fuel：燃油穿透penetration：穿透力distribution of fuel：燃油分布minimize：使….最小化maximize：使…..最大化shut down：关闭，切断cut off：终止，关闭check valve：止回阀jerk pump：喷射泵meter：计量，测量，米proper metering：精确计量parameter：参数size：尺寸carbon accumulation：结炭flow rate：流速break up：分裂，破裂，分手manufacture：制造商precaution：预防措施contamination：污染，脏污cetane rating：十六烷值cetane number：十六烷值secure the fuel supply：切断燃油供应take place：发生，开始commence：发生，开始slope：斜面spill port：回流孔，溢流孔build up：建立，积聚helix：螺旋槽MCR：最大持续功率base circle：基圆sulfur：硫water vapor：水蒸汽acid：酸，酸的malfunction：故障ash：灰duplex pressure gage：双联压力表thermostatic：恒温的needle valve：针阀differential needle valve：差压式针阀constant volume：定容constant pressure：定压unit injector：单体式喷油器misfiring：不发火vanadium：钒sodium：钠indicate：显示，表示contribute to：有利于，导致block：堵塞compressibility:压缩性remove：清除，去除sounding tube：深管sounding rod：量油杆oil impingement：注油cavitation （erosion）:气穴，汽蚀booster pump：增压泵 salt water：海水raw water：海水air cooler：空冷器make up：补充，补给distilled water：蒸馏水in contact with：与….接触facilitate：有利于，促进prior to：在….之前acid solution strength：酸性强度lime：石灰，氧化钙get rid of：去除，排除，摆脱release：释放mechanical property：机械性能expansion tank：膨胀水箱head tank：高置（膨胀）水箱coolant：冷却剂inoperative：不运转的，不运行的frost：结霜individual：单独的，独立的deposit：沉积物，沉淀物scale：水垢rust：生锈，铁锈dividing wall：分隔板overheat：过热explosion：爆炸chemical addition：投药，添加化学品additive：添加剂steam coil：蒸汽盘管anti-corrosion oil：防锈油inorganic inhibitor：无机缓蚀剂corrosion inhibitor：抗腐蚀剂regulate：调节modulate：调节head：压头volume：体积，容积closed cooling system：闭式冷却系统a portion of：一部分heat exchanger：换热器slightly：轻微的，轻度的nozzle holder：喷嘴座crack：裂纹suspect：怀疑baffle plate：挡板sacrificial zinc：保护性锌块soluble oil：可溶性油thermometer：温度计obstruct：堵塞，阻塞impeller：叶轮fin：翅片alarm：报警，警报器activate：激发，动作housing：壳体concentric：同心的bi-directional operation：双向运行compensating tank：补偿水箱（膨胀水箱）salinity：盐分，盐度alternative：选择，替代deaerating tank：除气柜three-way valve：三通阀flush：吹洗，冲洗oil barge：油驳interlocking device：连锁装置reversing：换向pilot air：控制空气，先导空气air distributor：空气分配器fusible plug：易熔塞guard against：防止air reservoir=air bottle=air receiver：空气瓶pneumatic control system：气动控制系统pneumatic tool：气动工具drain cock：放残考克blade：叶片turbine：透平remote valve：遥控阀air startlever：空气启动手柄instrument：仪表humidity：水分starting air distributor：启动空气分配器sufficient：充足的，足够的consecutive start：连续启动knocking sound：敲缸condensate：凝水condensation：冷凝run roughly：运转不平稳delay：推迟，延迟clearance volume：余隙容积two stage compressor：两级空气压缩机intercooler：中间冷却器，中冷器aftercooler：后冷器airborne：空气中携带的valve plate:阀片valve strip：阀片valve face：阀面valve seat：阀座volumetric efficiency：容积效率LP cylinder：低压缸HP cylinder：高压缸trip：跳闸overload relay：过载继电器dew point：露点splash lubrication：飞溅润滑water hammer：水击air delivery line：排出管路non-return valve：止回阀，单向阀carbonization：碳化throttling：节流solenoid：电磁的idle speed：怠速storage tank：储存柜neutralize：中和neutralization number：中和值alkalinity：碱detergency：清洁剂fundamental：基本的guard against：防止stern-tube bearing：尾轴承lignum vitae：铁梨木emulsion oil：乳化油，乳化防锈油sodium nitrite：硝酸钠additive：添加剂approved：认可的galvanize：镀锌investigation：调查gas seal 气封pot-shaped piston：筒状活塞analyze：分析total loss system：全消耗系统recirculation system：循环系统renew：更新，换新renewal：更新，换新static head：静压头in duplicate：一式两份，一式两台carry away：带走magnetic filter：磁性滤器blow out：吹洗in that：在于，因为former：前者latter：后者forced lubrication system：强制润滑系统employ：采用，使用，利用，雇佣hydrostatic lubrication：液体静力润滑impurity：杂质to a great extent：在很大程度上deterioration：恶化heat transfer：传热wear detritus：磨屑trouble-free life：无故障寿命dilute：冲淡，稀释，降低mist detector：油雾检测器monitor：检测，监控duplex filter：双联式滤器audible/visual alarm：声光报警shaker：振荡scuffing：划伤remain：保持remaining：剩余的retain：保留clogged：堵塞的hard varnish：硬的清漆pitting：点蚀oxidize：氧化carbon deposit：积碳detergent oil：净化油orifice：油孔diffuser：扩压器constant-pressure：定压增压pulse pressure：脉冲增压angle：角度，成….角度smoky exhaust：排气冒黑烟opposite：相反的，相对的supercharging：增压make use of：利用blower：鼓风机turboblower：涡轮增压器adjacent：相邻的in comparison to：与…相比compared to：与…相比fabricated：锻造的swirl：旋转rated speed：额定速度rated load：额定负载oxygen：氧气oxidize：使…氧化average：平均的velocity：速度directly proportional to：成正比characteristic：特点in conjunction with：和….一起performance：性能utilize：利用，使用furnish：提供muffle：消音，降低gas exchange：换气lose power：损失功率loss of pressure：失压take out=disengage:脱开put in=engage：合上FWE=finished with engine：完车give a trial：试车ahead and astern: 正倒车packing box：填料箱overhaul：大修stall：停止，停车enlarge：扩大，变大abnormal：不正常on no account：绝不，不可以seizure：卡住，咬缸gradually：逐渐地，逐步地remedy：补救，补修metalock：金属扣合法warm up:加温，暖机unless：除非surge：喘振spark：火星paint：油漆blistering：起泡peeling：剥落withdraw：取出routine 日常的，周期性的whilst=while：当…时候eliminate：消除，清除ambient temperature：环境温度regarding：关于with regard to：关于，对于….来说ventilation：通风vacuum：真空risk：风险，危险hazard：危险head wind：顶风heavy sea：风浪大combustion knock：燃烧过程粗暴wheelhouse：驾驶台contaminant：杂质，污染物cease：停止defect：损坏，缺陷sensor：传感器dead slow ahead：微速前进distribution：分配，布置，配电idle：闲置的guarantee：保证，确保pressure-volume diagram：压容图jerk pump：脉动泵，急拉式泵by-product：副产品erosion：剥蚀spark arrestor：火花消除器navigation：航行score：划痕scratch：刮痕abrasive particle：磨蚀颗粒pyrometer：高温计（测量排烟温度）manometer：压力计pressure gauge：压力表dial indicator：千分表，量缸表micrometer：千分表feeler：塞尺straight edge：直尺bridge gauge：桥规（轴颈下沉量，较小的主轴承磨损）blow-by：漏气break-in period：磨合期hone：搪磨detuner：减震器verify：检查，证实underway：航行时at partial load：部分负载localized：局部的local：当地的，机旁的file：锉blank off：堵死rotor：转子metal scraper：金属刮刀wrench：扳手moisture：水分muffler=silencer：消音器switch on：接通absolute pressure：绝对压力（=表压力+大气压力）air blast pump：抽气泵quay：码头direction handle：换向手柄coke deposit：积碳asphalt：沥青boss：桨毂hub：桨毂，轮毂variable pitch propeller：调距桨controllable pitch propeller：调距桨constant pitch propeller：定距桨fixed pitch propeller：定距桨tail shaft：尾轴intermediate shaft、；中间轴mass：重量in turn：依次，循序thrust block：推力块thrust pad：推力块reversing gear：换向装置axial movement：轴向运动solid propeller：整体式螺旋桨stem：船尾astern：船尾bow：艏，船头apparent slip：滑失比helix：螺旋线helicoidal：螺旋面，螺旋状的uniform pitch：定螺距non-uniform pitch：不定螺距pitch ratio：螺距比rubber：橡胶sterntube bearing：尾轴管轴承common rail system：共轨燃油系统VIT= variable injection timing: 可喷油定时森海海事服务。
汽轮机英语词汇TURBINE VOCABULARYI Power station电站1. power station电站2. power plant电站，发电设备3. utility电力部门4.independent power producer (IPP)独立发电项目，独立发电站5.nuclear power station核电站6. thermal power station火电站7. fossil (fired) power plant化石燃料电站，常规火电站8. combined heat power (CHP) plant热电联供机组9. steam power plant蒸汽电站蒸汽发电设备10. cogeneration power station热电联供电站11. coal fired power plant燃煤电站12. oil fired power plant燃油电站13. gas filed power plant燃气电站14. LNG power plant (liquefied natural gas)燃液化天然气电站15. BoP (balance of plant)电站辅机16. I&C (instrumentation and control)仪表和控制系统II Turbine透平，涡轮17. Turbine透平，涡轮18. steam turbine汽轮机19. gas turbine燃气轮机20. nuclear turbine核电汽轮机21. fossil turbine火电汽轮机22. industrial turbine工业透平23. cogeneration turbine热电联供透平24. condensing turbine凝汽式汽轮机25. back pressure turbine背压式汽轮机26. extraction turbine抽汽式汽轮机27. extraction condensing turbine抽汽凝汽式汽轮机28. single-extraction turbine单抽汽轮机29. double-extraction turbine双抽汽轮机30. mechanical drive turbine机械驱动汽轮机31. HP (IP, LP) turbine高（中、低）压缸32.sub-critical pressure turbine亚临界汽轮机33. super-critical pressure (SC) turbine 超临界汽轮机34. ultra-super critical (USC) pressure turbine超朝临界汽轮机35. BFPT (boiler feed pump turbine)给水泵汽轮机36. steam turbine with air-cooled condenser（air cooled steam turbine）空冷汽轮机37. reheat turbine再热汽轮机38. double-reheat turbine二次再热汽轮机39. wet steam turbine湿蒸汽汽轮机40. saturated steam turbine饱和蒸汽汽轮机41. full-speed turbine全速汽轮机42. half-speed turbine半速汽轮机43. tandem compound turbine单轴汽轮机44. cross compound turbine双轴汽轮机45. super (over)-high pressure turbine过高压汽轮机46. impulse (type) turbine冲动式汽轮机47. reaction (type) turbine反动式汽轮机48. axial flow turbine轴流透平49. radial flow turbine径流透平50. turbine with axial condenser轴向排汽汽轮机51. turbine with horizontal joint带有水平中分面的汽轮机52. turbine with vertical joint带有垂直中分面的汽轮机53. double flow turbine两排汽汽轮机54. triple flow turbine三排汽汽轮机56. single-casing turbine单缸汽轮机57. double-casing turbine双缸汽轮机58. turbine proper汽轮机本体59. oil turbine 油透平60. hydraulic turbine水轮机61. marine steam turbine船用汽轮机62.aeroderivative gas turbine航改式燃气轮机63. stationary steam turbine电站汽轮机64. auxiliary turbine辅助透平III Rotary parts回转件65. rotor转子66. rigid rotor刚性转子67. flexible rotor挠性转子68. solid (forged) rotor (monobloc rotor)整锻转子69. welded rotor焊接转子70. (hollow) drum (type) rotor鼓型转子71. built-up rotor组装转子72. rotor without center bore无中心孔转子73. HP-LP integrated rotor高/低压一体化转子74. shafting (shaft)轴系75. HP (IP, LP) rotor高（中、低）压转子76. thrust collar推力盘77. journal轴颈78. section of rotor转子区段79. (first, second ) critical speed一阶（二阶）临界转速80. extension shaft (spacer)中间轴，延伸段81. coupling联轴节82. flexible coupling挠性联轴节83. rigid coupling刚性联轴节84. semi-flexible coupling半挠性联轴节85. half coupling联轴节半部86. integral (forged) coupling整体（锻制）联轴节87. shrunk-on coupling红套联轴节88. spigot（rabbet）止口89. disk (disc) 叶轮90. rim (steeple)轮缘（枞树型叶根槽）91. hub轮毂92. body（web）轮体93. T （fir tree-type ) groove T型（枞树型）叶根槽94. balance hole (plane, weight, plug)平衡孔（平衡平面，平衡配重，平衡旋塞）95. keyway键槽96. disk of constant stress (conical profile)等强度（锥形）叶轮97. disk of constant thickness等厚度叶轮98. shrunk-on disk红套叶轮99. blade叶片100. moving (rotating, rotor) blade动叶101. bucket 动叶102. straight (tapered, twisted) blade直叶片（变截面叶片，扭曲叶片）103. last stage (last but one, penultimate) blade末级叶轮（次末级叶片）104. last (locking , gate) blade (piece)末叶片（锁紧叶片，锁紧件）105. free-stand blade自由叶片106. integral shroud blade整体围带叶轮107. triple-pin blade三联叶片108. bow blade马刀型叶片109. compound lean blade复合弯扭叶片110. concave (pressure) side内弧（压力侧）111. convex (suction) side 背弧（负压侧）112. tenon铆钉头113. leading (inlet) edge 进汽边114. trailing (outlet, exit) edge出汽边115. blade wake叶片尾流116. convergent-divergent channel (CD passage)缩张通道117. brazed (stellite) shield钎焊（斯太立）防蚀片118. lacing hole拉筋孔119. profile (section of blade)叶型，型线部分（叶片截面）120. reaction（degree）反动度121. cascade叶栅122. blade root叶根123. (three teeth, straight, curved ) fir- tree (blade) root（三齿直线/弧形）枞树型叶根124. ( five finger) fork type (blade) root（五叉）插入式叶根，叉型叶根125. tee (T-type) root T型叶根126. inverted-T (blade) root倒T型叶根127. straddle-type (blade) root 外包叶根128. straddle inverted T-root 外包倒T型叶根129. dovetail root (serrated root)燕尾型（齿型）叶根130. lacing (tie) wire 拉筋131. (lacing) lug (stub) 拉筋凸台132. loose lacing wire松拉筋133. tubular lacing wire管状拉筋134. shroud (band，cover)围带135. whole circle packed (continuously connected) shroud 整圈连接围带136. integral shroud整体围带137. snubber整体围带138. gauging (throat)喉节比（喉部）139. pitch diameter节径，平均直径140. top diameter（叶片）顶部直径IV. Stationary parts静止件141. casing (cylinder)汽缸，缸体142. outer casing外缸143. inner casing内缸144. single-shell casing单层缸145. double-shell casing双层缸146. cover (upper half)上半部147. base (lower half)下半部148. horizontal (split) joint水平中分面149. (massive) flange（厚）法兰150. (casing) bore（汽缸）洼窝151.fastener (bolt, nut, stud, dowel)紧固件（螺栓、螺母、螺柱、定位销）152. vertical flange垂直法兰153. tightness气密性154. inlet进口155. exhaust排汽口156. exhaust hood 排汽缸157. guide plate导流板158. diffuser扩压管159. flange bolt hole法兰螺栓孔160. shrunk-on ring红套箍环161. combined HP-IP casing高中压合缸162. thermal shield (baffle)挡热板163. single (double) flow HP turbine单流（双流）高压缸164. flow path (steam path)通流部分165.center support system滑键系统166. lug ( foot, pawl)猫爪167. thermal insulation保温设施168. enclosure (lagging)罩壳（外壳）169. diaphragm隔板170. blade ring ( diaphragm carrier)叶片持环，隔板套171. outer (inner) ring (of diaphragm)（隔板）外环（内环，隔板体）172. stationary (stator, guide ,nozzle) blade静叶，导叶，喷嘴173. vane (partition) 静叶174. cast-in (welded-in) diaphragm铸造（焊接）隔板rotary diaphragm回转隔板175. nozzle block (chest)喷嘴组（喷嘴室）176. diaphragm deflection隔板挠度177. bearing housing (pedestal)轴承箱178. front bearing housing (standard前轴承箱179. rear bearing housing 后轴承箱180. floor(-type) bearing落地式轴承181. bearing轴承182. journal (radial) bearing支持轴承（径向轴承）183. thrust (axial) bearin推力轴承轴向轴承184. tilting pad bearing可倾瓦轴承185. Kingsburg type thrust bearing金斯布里推力轴承186. Babbitt (white metal, bearing metal)巴氏合金187. bearing bush轴承壳体188. bearing body轴承体189. bearing pad轴瓦190. bearing cover (cap) 轴承上半191. 360°bearing整圆轴承192. elliptical bearing椭圆轴承193. three wedge bearing三油楔轴承194. self-aligning bearing自找中轴承195. sleeve bearing套筒式轴承196. sliding bearing滑动轴承197. (oil) pocket (wedge)油袋（油楔）198. oil film油膜199. oil (film) whip油膜振荡200. setting pad (segment)安装瓦块201. working pad (segment)工作瓦块202. oil ring (oil deflector)挡油环203. oil film stiffness油膜刚度204. armored thermocouple铠装式热电偶V. Main Valves主要阀门205. Main (HP) stop valve (MSV)主汽阀206. control (governing) valve (CV, GV)调节阀207. reheat (IP) stop valve(RSV)再热主汽阀208. intercept valve再热调节阀209. Combined main stop/governing valve联合式主汽/调节阀210. butterfly valve蝶阀211. piloted (pre-inlet) valve预启阀212. fast valve快速动作阀213. check (non-return) valve逆止阀214. solenoid valve电磁阀215. motor driven (operated) valve电动阀216.drain valve疏水阀217. diaphragm valve (atmospheric)膜片阀（大气阀）218. relief (exhaust) valve释放阀（放汽阀）219. safety valve安全阀220. extraction valve 抽汽阀221. stop valve截止阀222. flap valve翻板阀223. gate valve闸阀224. steam chest蒸汽室225. (valve) stem阀杆226. (valve) disk (plug)阀碟227. (valve ) seat阀座228. (valve) bonnet (cover)阀帽（阀盖）229. valve casing (chest)阀壳230. (valve) travel (stroke)阀门行程231. cross over (cross under)连通管232. anti-jamming(stick) test防卡涩试验VI. Various systems各种系统(1) Control system (control and protection system)调节系统（调节保安系统）233. Electro-hydraulic control system电液调节系统234. hydro-mechanical control system液压调节系统235. DEH (digital electro-hydraulic control system)数字式电液调节系统236. electro-hydraulic converter电液转换器237. trip跳闸，脱扣238. actuator执行机构239. servomotor油动机240. pilot (slide, spool) valve滑阀241. piston活塞242. piston rod活塞杆243. (oil) cylinder油缸244. (oil) window油口（窗）245. overlap覆盖度246. emergency governor危急遮断器247. speed governor 调速器248. MSV servomotor 主汽阀油动机249. spring support操纵座250. centrifugal stop bolt撞击子251. LVDT (linear variable differential transformer)线性阀位传感器252. safety test box安全试验盒253. relay继电器，继动器254. relay valve继动滑阀255. axial displacement indicator (transducer)轴向位移指示器（传感器） 256. overspeed protection超速保护257. differential expansion detecto r (transducer)差胀检出器（传感器） 258 lever杠杆259. (cam type) steam distribution device凸轮式排汽机构260. throttle governing节流调节261. nozzle governing喷嘴调节262. partial admission (degree)部分进汽（度）263.full arc admission全周进汽264. governing (control) stage (Curtis stage) 调节级（复速级）(2) Oil system油系统265. Main oil reservoir (tank)主油箱266. turbine oil透平油267. fire-resistant fluid抗燃油268. lube (lubrication ) oil润滑油269. HP control fluid高压控制油270. pressure (feed) line (pipe)供油管道271. retu rn (relief) line (pipe) 回油管道273.nested pipe（pipe in pipe）system套管式274. demister除油雾器275. fan风机276. mist separator 油污分离器277. oil purifier净油装置，油净化器278. oil filter滤油器279. oil cooler 冷油器280. overflow valve溢流阀281. oil vapour油雾，油气282. main oil pump( shaft d riven)主油泵283. impeller（主油泵）叶轮284. switch-over (change-over)切换汽封系统(3) Gland system285. Labyrinth gland 拉别林汽封，迷宫式汽封286. gland housing (casing)汽封体287. gland segment汽封弧段288. gland (sealing) ring 汽封环289. gland strip (comb)汽封片（齿）290. brush sealing刷子汽封291. leaf sealing薄叶汽封292. diaphragm gland隔板汽封293. gland over shroud (tip gland)围带汽封294. shaft gland轴封295. gland steam condenser (cooler)汽封冷却器296. spring-back sealing回弹式汽封297. glan d leak-off 漏汽298. gland ejector 汽封抽气器299. packing盘根，填函，汽封300. inner (outer) gland 内侧（外侧）汽封301. gland chamber (pocket) 汽封腔室302. dummy ring (balance piston)平衡环(4) Drain system疏水系统303. (drain) flash tank （疏水）扩容器304. drain port 疏水口305. cascade drain (system)逐级疏水306. drain cooler疏水冷却器(5) Bypass system旁路系统307. capacity容量308. HP (IP) bypass loop高压（中压）旁路回路309. start with bypass system利用旁路系统启动310. desuperheating and reducing device减温减压装置(6) Regenerative s ystem回热系统311. HP heater高压给水加热器（高加）312. LP heater低压给水加热器（低加）deaerator除氧器 313. terminal (temperature) difference (TTD) （温度）端差 314. drain subcooler approach (DCA)疏水过冷段315. shell side (design pressure)壳侧（设计压力）316. tube side (design pressu re)管侧（设计压力）317. condensing zone冷凝区318. drain subcooling zone疏水过冷区319. direct contact (LP) heater混合式（低压）加热器320. U tube U型管(7) Reheat system再热系统321. Cold reheat line再热冷端管道322. hot reheat line 再热热端管道323. MSR (moisture separator reheater)汽水分离再热器324. (single) reheat（一次）再热325. double reheat二次再热VII Auxiliaries辅机(1) Condenser凝汽器326. Shell-tube type heat exchanger壳管式热交换器327. surface condenser 表面式凝汽器328. direct contact condenser混合式凝汽器329. shell壳体330. (divided) water box (chamber)（对分）水室331. tube bundle管束332. tube plate (sheet) 管板333. support plate 支承隔板334. tube cleaner管子清洗器335. sponge ball cleaning system海绵球清洗系统336. double-shell condenser双壳体凝汽器337. single pass condenser单流程凝汽器338. air cooling zone空气冷却区339 air (cooled) condenser空冷凝汽器340. vacuum system真空系统341. evacuate 抽真空342. tube expander胀管器343. condensate冷凝水344. hot well (condensate sump)热井345. cooling rate冷却速率346. cleanness 清洁度347. condensate pump凝结水泵348. (condenser) neck（凝汽器）喉部349. expansion joint膨胀接头350. wave type (bellows) compensator波纹管补偿器 351. deaerating capacity除氧能力352. subcooling degree过冷度353. non-condensed (condensable) gas不凝结气体 354. booster pump增压泵cooler冷油器(2) Oil355. Filter过滤器strainer滤网356. cartridge滤芯357. vent通风口358. clogging堵塞359. twin-filter双联冷油器360. on－line change-over (switch-over) 在线切换(3) Ejector 抽气器361. Steam jet (air) ejector射汽抽气器362. water jet (air) eject or 射水抽气器363. (water ring) vacuum pump（水环）真空泵364. evacuation 抽真空365. vacuum establishing (forming) 建立真空366. starting ejector启动抽气器367. vacuum breaker真空破坏阀(4) Turning gear (device) or barring gear盘车装置368. Bull gear大齿轮369. driving ge ar驱动装置370. worm and (worm) gear涡轮蜗杆副371. turning by (every) 180°（每次）盘转180度372. jacking-up oil pump顶轴油泵373. (dis) engagement 啮合（脱开）V III Operation运行374. Operation mode运行方式Start (up)启动375. (emergency) shut down （紧急）停机376. daily start- stop (DSS) 日启停377. initial start初次启动378. cold (state) start 冷态启动379. warm start 温态启动380. hot start 热态启动381. extreme hot start极热态启动382. base load (unit) 基荷机组383. cyclic load循环负荷384. peak load峰荷385. peak shav ing调峰386. two-shift (operation)两班制（运行）387. cyclic duty capacity变负荷能力388. life cycle（使用）寿命389. life expenditure (CLE)寿命消耗390. life extension 寿命延长391. trip(ping)跳闸392. load tracking (following) capacity负荷跟踪能力393. boiler-turbine coordination control锅炉－汽机协调控制394. warming暖机395. l oading-up (down)升负荷（降负荷）396. unloading甩负荷397. load throw-off甩负荷398. run up升速399. run away飞车400. idle running惰行，空负荷运行401. speed up升速402 synchronization同步403. synchronizer同步器404. connect to grid并网405. rolling (by steam)冲转（用蒸汽）406. fixed pressure (start)定压（启动）407. sliding pressure (start)滑压（启动）408. combined (hybrid) fixed/sliding pressure operation定压/滑压混合运行方式 409. routine inspection日常检查410. planned maintenance计划维修411. overhaul (intervel)大修（间隔期）412. forced outage rate (FOR)强迫停机率413. repair检修414. availability可用率415. reliability可靠性416. control room 控制室417. corrosion腐蚀erosion浸蚀，水涮418. stress corrosion cracking (SCC) 应力腐蚀裂纹419. latch-on (reset)挂闸420. commission调试，试运行，交付使用。
燃气轮机词汇表AAcceptance test 验收实验Actual enthalpy drop (enthalpy rise) 实际焓降（焓增）Actuating oil system 压力油系统Aero-derivative gas turbine, aircraft-derivative gas turbine 航空衍生（派生）型燃气机轮Air charging system 空气冲气系统Air film cooling 气膜冷却Air intake duck 进气道Alarm and protection system 报警保护系统Annular com bustor 环行燃烧室Annulus drag loss 环壁阻力损失Area heat release rate 面积热强度Aspect ratio 展弦比Atomization 雾化Atomized particle size 雾化细度Autom atic starting tim e of gas turbine 燃气机轮的自动起动时间Auxiliary loads 辅助负荷Availability 可用性Average continuous running tim e of gas turbine 燃气机轮平均连续运行时间Axial displacem ent limit ing device 轴向位移保护装置Axial flow com pressor 轴流式压气机Axial flow turbine 轴流式透平Axial thrust 轴向推力BBase load rated output 基本负荷额定输出功率Black start 黑起动Blade 叶片Blade 叶片Blade height 叶（片）高（度）Blade inlet angle （叶片）进口角Blade outlet angle （叶片）出口角Blade profile 叶型Blade profile thickness 叶型厚度Blade root 叶根Bleed air/extraction air 抽气Blow-off 放气Blow-off value 放气阀Burner outlet tem perature 透平进口温度By-pass control 旁路控制By-pass control 旁路控制CCamber angle 叶型转折角Camber line 中弧线Can annular com bustor 环管型燃烧室Can-type com bustor 分管型燃烧室Carbon deposit 积碳Casing 气缸Cascade 叶栅Catalytic com bustion 催化燃烧Center support system 定中系统Centrifugal com pressor 径流式压气机Centripetal turbine 向心式（透平）Choking 堵塞Choking limit 阻塞极限Chord 弦长Closed-cycle 闭式循环Cogeneration 热电联供Cold starting 冷态起动Combined cycle 联合循环Combined cycle with m ulti-pressure level Rankine cycle 多压朗肯循环的联合循环Combined cycle with single pressure level Rankine cycle 单压朗肯循环的联合循环Combined supercharged boiler and gas turbine cycle 增压锅炉型联合循环Combustion cham ber 燃烧室Combustion intensity 燃烧强度Combustion liner/com bustor can/com bustor basket/flame tube 火焰筒Combustion stability 燃烧稳定性Combustion zone 燃烧区Combustion efficiency 燃烧室效率Combustion inspection 燃烧室检查Combustion outer casing 燃烧室外壳Combustion outlet tem perature 透平进口温度Combustion specific pressure loss 燃烧室比压力损失Compactness factor 紧凑系数Compressor 压气机Compressor characteristic curves 压气机特性线Compressor disc 压气机轮盘Compressor input power 压气机输入功率Compressor intake anti-icing system 压气机进气防冰系统Compressor rotor 压气机转子Compressor turbine 压气机透平Compressor washing system 压气机清洗系统Compressor wheel 压气机叶轮Constant power operation 恒功率运行Constant tem perature operation 恒温运行Control system 控制系统Convection cooling 对流冷却Cooled blade 冷却叶片Cooling down 冷却盘车Corrected flow 折算流量Corrected output 折算输出功率Corrected speed 折算转速Corrected therm al efficiency 折算热效率Counter flow com bustor 逆流式燃烧室Critical speed 临界转速Critical speed of rotor 转子临界速度Cross flame tube/inter-connector/cross fire tube/cross light tube 联烟管confidence interval 置信区间DDead band 迟缓率Dead center 死点Deep stall 渐进失速Degree of reaction 反动度Design condition 设计工况Deviation angle 落后角Diaphragm 隔板Diffuser 扩压器Dilution of rotation 旋转方向Disc-coupled vibration 轮系振动Disc-friction loss 轮盘摩擦损失Dual fuel nozzle 双燃料喷嘴Dual fuel system 双燃料系统Dynamic balancing 动平衡EElectro-hydraulic control system 电液调节系统Enclosures 罩壳End plate 端板Energy effectiveness 能量有效度Equivalence ratio 当量比Evaporative 蒸发冷却器Excess air ratio 过量空气比Exhaust casing(plenum)(for a turbine)/discharge casing(plenum)(for acom pressor) 排气缸（室）Exhaust duct 排气道Exhaust gas flow 排气流量Exhaust com bustion gas turbine 外燃式燃气轮机External loss 外损失Extraction gas turbine/bled gas turbine 抽气式燃气轮机FFast start 快速起动Feed-water heating heat recovery com bined cycle 给水加热型联合循环Final temperature difference 端差Flam e detector 火焰检测器Flam e failure limit 熄火极限Flam e-failure tripping device 火焰失效遮断装置Flam e-holder 火焰稳定器Flam e-out ripping device 熄火遮断装置Flexible rotor 挠性（柔性）转子Flow coefficient 流量系数Flow inlet angle 进气角Flow outlet angle 出气角Flow passage 通流部分Flow pattern 流型Flow turning angle 气流转折角Fluidized-bed com bustion com bined cycle 流化床联合循环Free piston turbine 自由活塞燃气轮机Front 额线Fuel coefficient 燃料系数Fuel consumption 燃料消耗量Fuel control system 燃料控制系统Fuel flow control valve 燃料流量控制阀Fuel injection pressure 燃料喷嘴压力Fuel injection pump 燃料注入泵Fuel injector 燃料喷嘴Fuel shut-off valve 燃料流量控制阀Fuel supply system 燃料供给系统Fuel treat m ent equipm ent 燃料处理设备Fuel-air ratio 燃料空气比Fuel fired combined cycle 排气全燃型联合循环GGas expander turbine 气体膨胀透平Gas flow bending stress 气流弯应力Gas fuel nozzle 气体燃料喷嘴Gas generator 燃气发生器Gas tem perature controller 燃气温度控制器Gas turbine 燃气轮机Gas turbine power plant 燃气轮机动力装置Governing system 调节系统HHeader 联箱Heat balance 热平衡Heat consum ption 热耗Heat exchanger plant 换热器板Heat exchanger tube 换热器管Heat loss 热损失Heat rate 热耗率Heat recovery steam generator/HRSG 余热锅炉Heat transfer rate of heating surface 受热表面的传热率Heat utilization 热能利用率Heater 加热器Heating surface area 受热面积High oil temperature protection device （润）滑油温过高保护装置High pressure com pressor 高压压气机High pressure turbine 高压透平Hollow blade 空心叶片Hot corrosion 热腐蚀Hot section inspection 热通道检查Hot starting 热态起动IIdle tim e 惰转时间Idling speed 空负荷转速Ignition 点火Ignition equipment 点火装置Ignition speed 点火转速Impingement cooling 冲击冷却Impulse turbine 冲动式透平Incidence 冲角Inlet air flow 进口空气流量Inlet casing(plenum) 进气缸（室）Inlet condition 进气参数Inlet guide vanes 进口导叶Inlet pressure 进口压力Inlet tem perature 进口温度Inner casing 内气缸Intake air filter 进口过滤器Integral(tip)shroud 叶冠Integrated coal-gasification combined cycle 整体煤气化联合循环Intercooled cycle 中间冷却循环（间冷循环）Intercooler 中间冷却器Intermediate pressure compressor 中压压气机Intermediate pressure turbine 内燃式燃气机轮Internal efficiency 内效率Internal loss 内损失Isentropic efficiency 等熵效率Isentropic efficiency 等熵效率Isentropic power 等熵功率LLagging 保温层Leaving velocity loss 余速损失Level pressure control 基准压力调节Light-off 着火Limit power 极限功率Load dump test 甩负荷试验Load rejection test 甩负荷试验Loading time 加载时间Locking piece 锁口件Logarithmic-m ean tem perature difference 对数平均温差Long shank blade root 长颈叶根Low fuel pressure protection device 燃料压力过低保护装置Low oil pressure protection device （润）滑油压力过低保护装置Low pressure com pressor 低压压气机Low pressure turbine 低压透平Lower emissions com bustors 低排放燃烧室Lubrication system 润滑油系统MMain gear 负荷齿轮箱（主齿轮箱）Major inspection 关键（部件）检查Major overhaul 大修Manual tripping device 手动遮断装置Mass to power ratio(m obile applications) 质量功率比（用于移动式燃气机轮）Matrix 蓄热体Maximum continuous power 最大连续功率Maximum momentary speed 飞升转速Mechanical efficiency 机械效率Mechanical efficiency 机械效率Mechanical loss 机械损失Method of modelling stage 模型级法Method of plane cascade 平面叶栅法Mobile gas turbine 移动式燃气机轮Moving blade/rotor blade 动叶片Multi-shaft gas turbine 多轴燃气机轮Multi-shaft type combined cycle 多轴联合循环Multi-spool gas turbine 多转子燃气机轮NNew and clean condition 新的和清洁的状态No-load operation 空负荷运行Normal start 正常起动Number of starts 起动次数OOff-design condition 变工况Open-cycle 开式循环Operating point 运行点Outer casing 外壳Outer casing 外壳Outlet condition 出气参数Outlet guide vanes 出口导叶Outlet pressure 出口压力Outlet pressure 出口压力Outlet pressure 出口压力Outlet tem perature 出口温度Outlet tem perature 出口温度Outlet tem perature/burner outlet tem perature 燃烧室出口温度Output limit 极限输出功率Output performance diagram 输出功率性能图Overspeed control device 超速控制装置Overspeed trip device 超速遮断装置Overtem perature control device 超温控制装置Overtem perature detector 超温检测器Overtem perature protective device 超温保护装置PPackaged gas turbine 箱式燃气轮机Particle separator 颗粒分离器Peak load rated output 尖峰负荷额定输出功率Performance m ap/characteristic m ap 特性图Pitch 节距Plate type recuperator 板式回热器Polytropic efficiency 多变效率Polytropic efficiency 多变效率Power recovery turbine 能量回收透平Power turbine 动力透平Power-heat ratio 功热比Precooler 预冷器Pressure level control 压力控制Pressure ratio 膨胀比（压比）Pressure ratio 膨胀比（压比）Primary air 一次空气Primary zone 一次燃烧区Profile loss 型面损失Protection system 保护系统Protective device test 保护设备试验Purging 清吹RRadial flow compressor 径流式压气机Radial flow turbine 径流式透平Rate of load-up 负荷上升率Rated condition 额定工况Rated output 额定输出功率Rated speed 额定转速Reaction turbine 反动失透平Recirculating zone 回流区Recuperator 表面式回热器Referred output 折算输出功率Referred speed 折算转速Referred thermal efficiency 折算热效率Regenerative cycle 回热循环Regenerator 回热器Regenerator 回热器Regenerator effectiveness 回热度Reheat combustor 再热燃烧室Reheat combustor 再热燃烧室Reheat cycle 再热循环Reheat factor 重热系数Reheat Rankine combined cycle 再热朗肯联合循环Relative dead center 相对死点Reliability 可靠性Reserve peak load output 备用尖峰负荷额定输出功率（应急尖峰符合额定输出功率）rigid rotor 刚性转子Rotating regenerator 回转式回热器（再生式回热器）Rotating stall 旋转失速Rotor blade loss 动叶损失Rotor blade/rotor bucket 动叶片Rotor without blades 转子体SSealing 气封Secondary air 二次空气Secondary flow loss 二次流损失Secondary zone 二次燃烧区Self-sustaining speed 自持转速Semi-base-load rated output 半基本负荷额定输出功率（中间负荷额定输出功率）Semiclosed-cycle 半闭式循环Shaft output 轴输出功率Shafting vibration 轴系振动Shell 壳体Shell and tube recuperator 壳管式回热器Silencer 消音器Silo combustor 筒形燃烧室Simple cycle 简单循环Single-shaft gas turbine 单轴燃气机轮Single-shaft type combined cycle 单轴联合循环Site conditions 现场条件Site rated output 现场额定输出功率Soot blower 吹灰器Spacer 隔叶块Specific com bustion intensity 比热燃烧强度Specific fuel consumption 燃料消耗率Specific power 比功率Speed changer 转速变换器Specific changer/synchronizer 转速变换器Speed governor 转速调节器Speed governor droop 转速不等率Spray cone angle 雾化锥角Stabilization time 稳定性时间Stage 级Stage efficiency 级效率Stagger angle 安装角Stall 失速Standard at m osphere 标准大气Standard rated output 标准额定输出功率Standard reference conditions 标准参考条件start 起动Starter cut-off 起动机脱扣Starting characteristics diagram 起动特性图Starting characteristics test 起动特性试验Starting equipment 起动设备Starting tim e 起动时间Static balancing 静平衡Stationary blade 静叶片Stationary blade loss 静叶损失Stationary gas turbine 固定式燃气机轮Stator 静子Steady-state increm ental speed regulatio n 稳态转速增量调节Steady-state speed 静态转速Steady-state speed droop 静态转速不等率Steady-state speed regulation 静态转速调节Steam and/or water injection 蒸汽和/或水的喷注Steam injection gas turbine 注蒸汽燃气机轮Steam/water injection equipment 注蒸汽/注水设备Steam-air ratio 蒸汽空气比Steam-gas power ratio 蒸燃功比Stoichiom etric fuel-air ratio 理论（化学计量）燃烧空气比Straight blade 直叶片Straight-flow combustor 顺流式燃烧室Supplementary fired com bined cycle 补燃型联合循环Surge 旋转失速Surge limit 喘振边界Surge m argin 喘振裕度Surge-preventing device 防喘装置Swirler 旋流器TTem perature effectiveness 温度有效率Tem perature pattern factor 温度场系数Tem perature ratio 温比Theoretical com bustion Tem perature 理论燃烧温度Therm al blockage 热（悬）挂Therm al efficiency 热效率Therm al fatigue 热疲劳Therm al shock 热冲击Therm odynamic performance test 热力性能试验Throat area （叶栅）喉部面积Tip-hub ratio 轮毂比Total pressure loss coefficient 全压损失系数Total pressure loss for air side 空气侧压全损失Total pressure loss for gas side 燃气侧压全损失Total pressure recover factor 全压恢复系数Transpiration cooling 发散冷却Tube bundle/tube nest 管束Tube plate 管板Turbine 透平Turbine characteristic curves 透平特性线Turbine diaphragm 透平隔板Turbine disc 透平轮盘Turbine entry temperature 透平进口温度Turbine nozzle 透平喷嘴Turbine power output 透平输出功率Turbine reference inlet tem perature 透平参考进口温度Turbine rotor 透平转子Turbine rotor inlet temperature 透平转子进口温度Turbine trip speed 燃气轮机跳闸转速Turbine trip speed 燃气轮机跳闸转速Turbine washing equipment 透平清洗设备Turbine wheel 透平叶轮Turbine gear 盘车装置Turning/barring 盘车Twisted blade 扭叶片UUn-fired combined cycle 无补燃型联合循环VVane 静叶Vane 静叶Variable stator blade 可调静叶片Variable stator blade 可调静叶片Variable-geom etry gas turbine 变几何燃气机轮Velocity coefficient 速度系数Velocity ratio 速比Velocity triangle 速度三角形Volumetric heat release rate 容积热强度WWheel efficiency 轮周效率Working fluid heater 工质加热器Working fluid heater efficiency 工质加热器效率。
