5931wifi模块规格书

RDT-GW519无线4G路由图传模块使用说明书Ver1.0网站： QQ：1254960187电话：*************邮箱：*********************地址：深圳市龙华区大浪街道浪口社区华昌路金星工业园4栋602文档RDT-GW519无线4G路由图传模块使用说明书版本号Ver1.0发布日期2020-06-281.产品简介RDT-GW519无线4G路由图传模块采用MTK工业级MT7628NN无线路由器方案，4G 模组采用美格的华为4G方案全网通SLM790工业模组，产品基于4G网络需求研发的高性能优异稳定的无线4G路由通信产品。

产品提供2路100M以太网口、300M WIFI无线接口、UART接口（TTL电平/RS-232/RS-485可选），可以对接多种终端设备，带双网口WAN口/LAN口可选，方案独特，使得产品稳定性得到行业的认可。

支持WEB配置方式，管理方便简单，支持远程云端管理。

它主要应用于行业用户的数据传输业务，支持数据透明传输、VPN、无线桥接、图像传输、设备监控以及无线路由上网等功能。

RDT-GW519无线4G路由图传模块广泛在电力、石油、煤矿、金融、通信、公安、热力、工业控制、气象、水利、交通、市政等环境复杂行业应用。

2.外观和接口接口说明指示灯状态说明名称状态描述WLAN闪烁无线WIFI 已开启熄灭无线WIFI 未开启4G快闪上电后快闪，说明正在执行拨号过程常亮上电后常亮，说明拨号成功熄灭上电后熄灭，说明未识别LTE 模组或SIM 卡或非4G 工作模式系统灯(SYS)熄灭上电熄灭，说明供电不正常或系统没有启动。

慢闪上电后，变为慢闪，说明系统运行正常3.设置准备项目参数WAN 口(ETH0)1个10/100M 自适应WAN 口，内置隔离，支持自动翻转（Auto MDI/MDIX ）、4G 模式下为LAN 口LAN 口(ETH4)1个10/100M 自适应LAN 口，支持自动翻转（Auto MDI/MDIX ）串口2个串口，UART0为console 、UART1为数据传输口USB 口（PCIE ）USB2.0口,接4G 模组.指示灯3个指示灯(SYS 、4G 、WLAN)天线接口2个一代I-PEX 座电源接口5-12V /2A ±0.2V3.1连接设备您可通过以下步骤将你的设备连接到路由器。

WIFI模块硬件设计规格书版本: 1.0目录1 模块总体介绍（Gerneral introduction) (4)1.1 概述及实物图片（Description） (4)1.2 应用领域（Application） (6)1.3 产品特性 (Main feature) (6)2 模块电气特性（Electric Characteristics） (8)2.1 极限条件（Absolute Maximum Ratings） (8)2.2 工作条件（Recommended Operate Range） (8)2.3 电气特性（General Electric Characteristics）............................... (8)2.4 拼脚定义（Pin Assignment and Description） (9)3 模块应用设计指导(Application note) (14)3.1 功能框图（Function Block description） (14)3.2 工作状态描述（state descriptions） (14)3.3 硬件应用接口概述 (15)3.4 电源和驱动应用接口 (16)3.4.1 电源和驱动管脚定义 (16)3.4.2 主电源供电特性Vbat (17)3.4.3 备用电池RTC................................................................................. ........................... (18)3.4.4 开关机及复位(Power ON/OFF and Reset) (19)3.4.5 充电输入口VCHGIN............................ ................................. .. (20)3.4.6 充电输出口VCHGOUT........................... ................................. . (21)3.4.7 电池检测专用ADC口ADC3/BAT_ID ........................... .. (21)3.4.8 4路LDO输出.................................................... .. (22)3.4.9 LED-驱动 (22)3.4.10 KEY_ LED-驱动 (23)3.4.11电源电路参考设计 (23)3.5 按键接口........................................... . (24)3.6 语音接口........................................... (25)3.6.1模拟音频差分输入主MIC0和辅助MIC1.................................................................................. . (25)3.6.2 模拟音频差分输出受话器REC (26)3.6.3 模拟音频差分输出喇叭SPK (26)3.7 UART 接口 (27)3.8 IIC 接口 (28)3.9 LCD IO驱动为2.8V SPI 接口 (28)3.10 LCD IO驱动为1.8V SPI 接口 (29)3.11 USB 接口..................................... . (30)3.12 SIM 卡接口 (31)3.13 T-F卡接口 (32)3.14 F M 接口 (34)3.15 BT 接口 (34)3.16 通用GPIO接口 (35)3.17 中断口EINT (35)3.18 模拟输入ADC (35)3.19 射频天线接口 (36)4硬件设计指南 (37)4.1 PCB板布局说明 (37)4.2 PCB 关键走线说明......................................................... (37)5 机械特性 (38)5.1 模块机械尺寸 (38)5.2 模块产品 Top－View 视图.......................................... (39)5.3模块供电要求及接法 (41)5.4下载软件 (41)5.5模块开机 (41)5.6 RF测试连接 (41)6 附录 (42)6.1 射频指标 (42)6.2 通信专用术语 (42)1 模块总体介绍1.1 概述及实物图片GW01_GSM&WIFI是一款GSM/GPRS/WIFI无线四频(GSM850/GSM900/DCS1800/PCS1900)工业模块，可以覆盖全球通用GSM频段。

1 / 10 REV01 2 / 10 REV01 作者审核批准宝烽软件科技 BAOFENG SOFTWARE TECHNOLOGY版本V1.0.02014-11-17创建宝烽软件科技有限公司宝宝烽软件科技BAOFENG SOFTWARETECHNOLOGY目录12 规范性引用文件 (2)3 缩略语 (2)4 介绍 (3)5 特征 (3)5.1 5.2 5.3 接口 (3)无线 (3)其它 (4)6 规格 (4)7 外接天线推荐规格 (5)8 接口信号 (5)9 环境适应性试验 (7)9.1 9.2 9.3 9.4 9.5 9.6 9.7 低温工作试验 (7)低温存储试验 (8)高温工作试验 (8)高温存储试验 (8)温度冲击试验 (8)震动试验 (8)环保认证 (8)宝烽软件科技有限公司概述 (2)3 / 10 REV01 宝烽软件科技BAOFENG SOFTWARE宝烽软件科技有限公司TECHNOLOGY1 概本规格书规定了基于 HED10W07SN的表贴式 SPI无线模块的物理特性、技术指标、通 信协议、产品功能、性能、稳定性、环境适应性以及安全性等方面的技术标准。

2 规范性引用文件《GB 15629.11-2003》《IEEE 802.11-1999》《IEEE 802.11a-1999》《IEEE 802.11b-1999》《IEEE 802.11b-1999_Cor1-2001》《IEEE 802.11d-2001》《IEEE 802.11F-2003》《IEEE 802.11G-2003》《IEEE 802.11h-2003》《IEEE 802.11i-2004》《IEEE 802.11i-2004_Decrypt》3 缩略语IBSS：由网卡组建的网络BSS：由 AP组建的网络RTS：请求发送控制帧CTS：清除发送控制帧WEP：有线对等加密TKIP：临时密钥完整性协议CCMP：计数模式 CBC-MAC协议WPA：Wi-Fi保护接入WPA2：WPA的第 2版，在 WPA基础上加入了 CCMPAP：无线网卡接入点SSID：无线网络名称标识BSSID：区分网络的唯一标识4 / 10 REV01 宝烽软件科技BAOFENG SOFTWARETECHNOLOGY 宝烽软件科技有限公司4介绍本产品是基于 HED10W07SN 单芯片设计的表贴式 SPI 无线产品模块，形成新的 SPI 接口网卡，型号为 BF1005 特征基于 HED10W07SN 单芯片设计的表贴式 SPI 无线模块产品应用于各种嵌入式设备， 其主要特征如下：5.1 接口9 邮票孔式接口，间距 50mil9 8个 GPIO@SPI；6个 GPIO@UART9 I2C9 4路 ADC9 H-SPI9 SDIO9 L-SPI9 UART9 5个独立 GPIO5.2 无线9 支持 IEEE802.11b/g/i无线标准9 支持频率范围：2.412~2.484 GHz9 支持基础网（Infra）ζ 支持多种安全认证机制：OPEN/WEP64/WEP128/ TKIP/CCMP(AES)OPEN/WEP/WPA-PSK/WPA2-PSKζ 支持快速联网模式（指定信道与BSSID）ζ 支持无线漫游ζ 支持Sleep节能模式（PS-POLL方式）ζ 支持Standby节电模式ζ 支持WPS功能9 支持自组网（Adhoc）：ζ 支持OPEN、WEP加密认证ζ 支持网络不存在时自动创建5 / 10 REV01 6 / 10 REV01 宝烽软件科技有限公司ζ 支持ζ 最多支持4个station连接 ζ 支持STA节能（PS-POLL方式） 5.3 其它9 支持 SPI 、SDIO 、UART 接口通信ζ 支持高速 SPI 数据接口，接口速率最高到 50Mbps ζ 支持高速 SDIO 数据接口，接口速率最高到 50Mbps ζ 支持 UART 数据接口，接口速率 1200 - 2Mbps 9 支持用户可编程的 GPIO 控制 9 支持命令工作模式ζ 基于 HEX 编码的精简指令协议(SPI 、SDIO 接口) ζ 基于 ASCII 编码的 AT+指令协议（UART 接口） 9 支持自动工作模式 ζ 基于参数配置方式9 支持多种网络协议：TCP/UDP/ICMP/DHCP/DNS/HTTP 9 支持 DHCP Server 、DNS Server 9 支持可扩展的 WEB 服务器 ζ 内置参数配置和固件升级网页 ζ 支持用户自定义网页9 支持基于浏览器和串口方式的参数配置 9 支持基于浏览器和串口方式的固件在线升级 9 支持基于串口方式的模块生产测试 6 规格表 6-1 产品规格列表参 数项 目 无线标准 频率范围 IEEE802.11b/g/i 2.412~2.484 GHz802.11b: -82 dBm @ 11Mbps （typical ） 802.11g: -68 dBm @ 54Mbps （typical ）802.11b: 1,2,5.5,11 Mbps数据速率 802.11g: 6,9,12,18,24,36,48,54 MbpsDSSS, OFDM, DBPSK, DQPSK, CCK, QAM16/64调制方式宝烽软件科技 BAOFENG SOFTWARE TECHNOLOGY 无线部接收灵敏度无线部分7 / 10 REV01 天线接口 宝烽软件科技有限公司802.11g: 10±2 dBm （typical ） 接口类型 接口速率 工作电压 SPI/UART/GPIO 20Mbps@SPI(max) 2Mbps@UART(max) 3.3±0.3 V 硬件部分RX ：130mW 功耗TX ：265mW 工作湿度 存储温度 5%~90%（无凝结） -55~+125 ℃ 工作温度 -40~+85℃ 外形尺寸 22mm ×33mm 网络类型 Infra/Adhoc/APWEP/WPA-PSK/WPA2-PSK 认证方式 软件部加密方式 WPS 功能 WEP64/WEP128/TKIP/CCMP(AES) WPS节能机制 PS-POLL/Standby网络协议 TCP/UDP/ARP/ICMP/DHCP/DNS/HTTP 精简指令协议 接口协议AT+指令集7 外接天线推荐规格表 7-1 外接天线规格号码 说 明频率范围 阻抗2.412~2.4825 GHz50 Ω 电压驻波比 ≦1.5 极化 接口 垂直极化 IP X8 接口信号本模块邮票孔管脚排列如下图 7-1所示，其管脚说明如下表 7-1 所示：宝烽软件科技 BAOFENG SOFTWARE TECHNOLOGYIPX/微带天线 软件部分8 / 10 REV01 宝烽软件科技有限公司201微 带 天 线TL6 SOCIPX2140图 8-1 邮票孔管脚排列顺序 表 8-1 邮票孔管脚说明号码 描述 方向 说 明1 SPI _LS _DO O O I O G 低速SPI（主）数据输出信号 低速SPI（主）时钟信号2 SPI _LS _CK3 SPI _LS _DI4 SPI _LS _CS5 GND 低速SPI（主）数据输入信号 本地FLASH片选信号 接地6 V DD25_EF U SE _TEST NCNC 7 GND G I I I接地 8 CHIP _AWAKE 9 /RST _N 唤醒信号复位信号，低电平有效 低速SPI（主）片选信号10 FLASH _CS _IN 11 GPIO12 I /O GPIO 12 GND G I I 接地 13 SPI _HS _CK 14 BOOT _M ODE0 15 SPI _HS _INT /U ART1_R X D高速SPI（从）时钟信号 芯片固件加载模式选择高速SPI（从）中断/U ART1数据接收I /O16 SPI _HS _CS /GPIO 3 I /O 高速SPI（从）片选信号/GPIO 17 SPI _HS _DI /GPIO4 I /O 高速SPI（从）数据接收/GPIO 宝烽软件科技 BAOFENG SOFTWARE TECHNOLOGY9 / 10 REV01 宝烽软件科技有限公司18 SPI_HS_DO/GPIO5 19 GND20 UART1_TXD/GPIO6 I/O 串口 G接地 21 GND G接地22 GPIO13 23 GPIO11 24 GNDI/OGPIOI/O GPIOG 接地 25 I2C_SCL/UART1_CTS/GPIO8I2C 总线时钟信号/串口 1 流控信号I/O/GPIO 26 I2C_SDA/UART1_RTS/GPIO9 I2C 总线数据信号/串口 1 流控信号 I/O /GPIO27 BOOT_MODE2 28 GNDI G芯片固件加载模式选择 接地29 UART0_RXD/GPIO15 I/O 串口0数据接收/GPIO 30 UART0_TXD/GPIO14 I/O 串口0数据发送/GPIO 31 SDADC_AIN3 32 SDADC_AIN2 33 SDADC_AIN1 34 SDADC_AIN0 35 GND I I I I G P P G G GDAC模拟输入端口3 DAC模拟输入端口2 DAC模拟输入端口1 DAC模拟输入端口0 接地36 VDD33 37 VDD33 38 GND 3.3V电源输入引脚 3.3V电源输入引脚 接地 39 GND 接地 40 GND接地9 9.1 低温工作试验9 参考标准：GB/T 2423.1-20019 在环境温度为-40±1℃条件下，网卡模块样品可连续工作 72 小时，试验后各项性能和功能保持良好状态。

Wi-Fi通信模块使用说明石家庄陆杰电子科技有限公司版本：20230309V1.1基本说明感谢您购买了陆杰Wi-Fi通信模块（WiFi-UART）。

本手册主要介绍Wi-Fi通信模块（WiFi-UART）使用内容。

在使用产品之前，请仔细阅读本手册，并在充分理解手册内容的前提下，进行使用软件及硬件方面的介绍，请查阅相关手册。

用户须知手册等其他技术资料中所列举的示例仅供用户理解、参考用，不保证一定动作。

将该产品与其他产品组合使用的时候，请确认是否符合有关规格、原则等。

使用该产品时，请自行确认是否符合要求以及安全，对于本产品故障而可能引发机器故障或损失时，请自行设置后备及安全功能。

责任申明手册中的内容虽然已经过仔细的核对，但差错难免，我们不能保证完全一致。

我们会经常检查手册中的内容，并在后续版本中进行更正，欢迎提出宝贵意见。

手册中所介绍的内容，如有变动，请谅解不另行通知。

联系方式如果您有任何关于本产品的使用问题，请与购买产品的代理商、办事处联系，也可以直接与陆杰公司联系。

电话：400-657-7769*************地址：石家庄栾城区邵家庄工业路2号邮编：050000网址：/未经明确的书面许可，不得复制、传翻或使用本资料及其中的内容，违者要对造成的损失承担责任。

保留包括实用模块或设计的专利许可及注册中提供的所有权力。

二零二二年六月目录一、基本说明 (4)二、硬件设备说明 (4)三、连接方式说明 (5)四、配置软件说明 (5)五、操作说明 (6)六、微信小程序使用说明 (7)七、故障排除 (10)一、基本说明Wi-Fi通信模块（Wi-Fi-UART）（以下简称模块）具备USB转232、转485、转422、串口转Wi-Fi的功能，适用PLC、HMI等串口设备的读写监控，数据传输功能。

1)通过WiFi-UART配置软件PC端或微信小程序，可以配置模块接入互联网，实现远程数据透传。

2)通过USB接口，插入电脑，可以实现USB转232（485，422）功能。

SDIO PRODUCT SPECIFICATION IEEE 802.11 b/g/n 2.4GHz 1T1R WiFi ModuleRF-SM01 (MTK 5931)SDIO ModuleVersion 1.0PRODUCT DESCRIPTIONRL-SM01 MT5931 provides the best and most convenient connectivity functions. RL-SM01MT5931 implements advanced and sophisticated radio coexistence algorithms and hardware mechanisms. The enhanced overall quality for simultaneous voice, data, and audio/video transmission on mobile phone and Tablet PC can be achieved. The small package size with low power consumption reduces the PCB layout area.PRODUCT FEATURESO Embedded RISC core for better system level managementO Coexistence: IEEE 802.15.2 external three-wire coexistence scheme to support additionalwireless technologies such as 3G, GPS and WiMAX_ Self calibration.O Integrated switching regulator enables direct connection to battery.O Best-in-class current consumption performanceO Intelligent BT/WLAN coexistence scheme that goes beyond PTA signaling (for example, transmitwindow and duration that take into account of protocol exchange sequence, frequency, etc.)O TFBGA (5.1x5.3mm2) packagesO 2.4GHz single stream 802.11 b/g/n MAC/BB/RFO 802.11 d/h/k compliantO Security: WFA WPA/WPA2 personal, WPS2.0, WAPI (hardware)O QoS: WFA WMM, WMM PSO Supports 802.11n optional features: STBC, A-MPDU, Blk-Ack, RIFS, MCS Feedback, 20/40 MHzcoexistence (PCO), unscheduled PSMPO Supports 802.11w protected managed framesO Supports Wi-Fi DirectO Interface: SDIO 2.0 (4-bit & 1-bit)O Per packet Tx power controlPRODUCT SPECIFICATIONSMain chipsetWiFi/BT Single Chip: Realtek RTL8723AS-CGFunctional SpecificationsWiFi:IEEE 802.11b, IEEE 802.11g, Draft IEEE 802.11n, StandardsBus Interface WiFi: SDIOForm Factor L*W*H = 14.7mm*12.4mm*1.9mm802.11b: 11, 5.5, 2, 1 Mbps802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps802.11n:Data Rate MCS 0 to 7 for HT20MHzMCS 0 to 7 for HT40MHzWiFi:802.11b:CCK, DQPSK, DBPSK802.11g: 64 QAM, 16 QAM, QPSK, BPSK 802.11n:Modulation Techniques64 QAM, 16 QAM, QPSK, BPSKNetwork Architecture WiFi:Ad-hoc mode (Peer-to-Peer )Infrastructure modeWiFi 2.4GHz:11: (Ch. 1-11) – United StatesOperating Channel 13: (Ch. 1-13) – Europe 14: (Ch. 1-14) – Japan Frequency Range 2.400GHz ~ 2.4835 GHz802.11b@11Mbps 16dBm 802.11g@6Mbps16dBm802.11n 16dBm (MCS0_HT20)802.11g@54Mbps14dBm13dBm (MCS 7_HT20)13dBm (MCS 0_HT40)13dBm (MCS 7_HT40)Transmit Output Power – 1x1 (Tolerance: ±1.5dBm)802.11b@11Mbps -85dBm 802.11g@54Mbps-72dBm802.11n -69dBm (MCS7_HT20)-66dBm (MCS 7_HT40)Receiver SensitivityWiFi :WPA, WPA-PSK, WPA2, WPA2-PSK, WEP 64bit & 128bit, IEEE SecuritySimple ParingOperating Voltage 3.3 V ±3% I/O supply voltageOS supported Windows XP/Win7/Linux/AndroidPower Consumption (3.3V)(Typical)WiFi :TX Mode: (Conituous mode) 50mA (MCS7/BW40/13dBm)RX Mode: (Conituous mode) 30mA (MCS7/BW40/-60dBm)Associated Idle: 4mAUnassociated Idle: 3mARF disable Mode: 3mAMechanicalLength Width HeightDimensions (mm)14.7 12.4 1.9(Tolerance:±0.2mm) (Tolerance:±0.2mm) (Tolerance:±0.2mm)Fig.1 Top Layer (Top View)Fig.2 Size chart (Top View)Block DiagramMODULE PIN ASSIGNMENT Pin FunctionPinFunction1 VBAT 9 SD_D12 GND10 SYSRST_BT 3 DVDD 11 GND 4 SD_D2 12 WIFI_RF 5 SD_D3 13 GND6 SD_CMD 14 WIFI_EN PMU enable from host7 SD_CLK 15 GND8SD_D016FSOURCEModule PIN feet definition figureWIFI\BT RF Circuit reference pictures注：以上RF 走线要做50欧的阻抗，走线不能走90度，走线不能长于15MM 。

FUNCTIONThe FMR1 Fixture Module - Relay is a high quality wire-in home automation load controller that is capable of turning 120VAC appliances and fluorescent lamps ON and OFF based on digital commands received over the power wiring from a remote UPB (Universal Powerline Bus) controller. UPB controllers and modules can be freely located anywhere throughout the home. No additional wiring is required and no radio frequency signals are used for communication. IMPORTANT SAFETY INSTRUCTIONSWhen using electrical products, basic safety precautions should always be followed, including the following:1.READ AND FOLLOW ALL SAFETY INSTRUCTIONS.2.Keep away from water. If the product comes in contactwith water or other liquid, turn off the circuit breaker and unplug the product immediately.3.Never use products that have been dropped ordamaged.4.Do not use this product outdoors.5.Do not use this product for other than its intendedpurpose.6.Do not connect multiple lamps or appliances that, whencombined, exceed the maximum load ratings of theproduct.7.To avoid any risk of fire, burns, personal injury or electricshock, install this product out of the reach of smallchildren.8.Do not cover this product with any material when in use.9.This product uses grounded plugs and sockets to reducethe risk of electric shock. These plugs and sockets fit only one way. If they do not fit, consult an electrician.10.SAVE THESE INSTRUCTIONS. INSTALLATIONThe Fixture Module – Relay is designed for indoor use with devices that are permanently wired into the home electrical system. To install the FMR1 module:1.Locate the device to be controlled. Note that the devicepower rating must not exceed 20 amps.2.Disconnect power at the circuit breaker.3.Remove any existing ceiling or wall fixture hardware for thedevice. Disconnect the black wire that supplies power tothe device.ing a wire nut, connect the black (Line) wire of thefixture module to the black (Line) power wire.ing a wire nut, connect the red (load output) wire of thefixture module to the black wire from the lighting fixture or device being controlled.ing a large wire nut, connect the white (Neutral) wire ofthe fixture module to the white (Neutral) power wire andthe white wire from the lighting fixture.7.Refer to instructions on CONFUGRATION and OPERATIONprior to placing the fixture module in its final location, as it may be necessary to have access to the Program Switch inorder to add the module to the UPB network and test itsoperation. Temporarily restore power in order to performthese functions. Disconnect power again when finished. 8.Once proper operation is established, fit the module intothe outlet box or otherwise secure it using wire ties orfitting the nipple into a ½” knockout. Reinstall fixturehardware as needed.CAUTION: Do not insert metal objects into the module while it is connected to power.FixtureCONFIGURATIONOnce your FMR1 is installed it can be configured either manually or with the UPStart Setup Software.Manual configuration can be used to add your FMR1 device into a UPB network and link it to controller buttons. Refer to the Keypad Controller’s Manual Configuration Guide available on the PulseWorx website () for more details.Although the factory default operation of the FMR1 is useful in many situations, it is highly recommended that your device be configured with UPStart Setup Software so that you can take advantage of its many configurable features.PCS has developed a Powerline Interface Module (PIM) and free UPB Setup Tool software (UPStart) to help you configure all of your PulseWorx Lighting System devices. User’s Guides are available on the PulseWorx web site: to explain how to configure your system.SETUP ModeWhen configuring a UPB system, it will be necessary to place the FMR1 in SETUP mode. To do this, press the Program Button (see illustration) five times rapidly using a non-metallic toothpick. The Status LED will continuously blink Blue when the device is in SETUP mode. To exit SETUP mode, press the Program Button once or wait five minutes for it to time out.OPERATIONThe Fixture Module operates according to commands sent by one or more UPB controllers. The FMR1 can accept powerline commands from any UPB-compatible transmitter such as PulseWorx Keypad Controllers, Timed Event Controllers, Wall Switches, Interface Modules, approved Third-Party Controllers and touch screens. The FMR1 can be a member of up to 16 scenes with the capability to store a pre-set relay state (on, off, or blink) for each scene.AUTO-OFF TimerNew for Generation 2 is the ability to set a maximum on time. If you forget to shut the fixture off yourself the fixture module will do it for you automatically. The FMR1 can be configured to inform the rest of the network when it has automatically turned the appliance off. This allows the FMR1 to remotely control other devices or update feedback indicators such as LEDs. TEST ModeA manual test feature allows the device to be turned ON and OFF locally. To enable the TEST mode press and hold the Program Button on the FMR1 for at least three seconds. The Status LED will blink Magenta to indicate TEST mode. The fixture can now be turned ON and OFF by single-tapping the Program Button. Press and hold the Program Button again for at least three seconds to exit from TEST mode.Factory Default SettingsTo restore the following default settings put the FMR1 into SETUP mode and then press the Program Button ten times rapidly. The Status LED will blink red to indicate that factory defaults have been restored. Press the Program Button twice more to stop the blinking.Network ID:255Unit ID:61Network Password:1234Receive Components:Link #1 = ONLink #2 = OFFLink #8 = Blink @ .5 sec TYPICAL USESThe FMR1 is perfect for controlling 120VAC non-dimming loads such as:•Fans,•Pumps,•Low voltage transformers,•Coffee makers,•Christmas lights.LIMITED WARRANTYSeller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in materials and workmanship for a period of five years from the date of purchase. Refer to the warranty information on the PulseWorx website () for exact details.。

Dimensions: [mm]26070562910112607056291011Cautions and Warnings:The following conditions apply to all goods within the product series of wireless connectivity of Würth Elektronik eiSos GmbH & Co. KG:General:•This electronic component is designed and developed with the intention for use in general electronic equipment.•Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network, etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury.•Electronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer.•The component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the wire insulation may be damaged or dissolved.•Do not drop or impact the components, the component may be damaged.•Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not guarantee any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time.•The customer is responsible for the functionality of their own products. All technical specifications for standard products also apply to customer specific products.Product specific:Soldering:•The solder profile must comply with the technical product specifications. All other profiles will void the warranty.•All other soldering methods are at the customer’s own risk.Cleaning and Washing:•Washing agents used during the production to clean the customer application might damage or change the characteristics of the component. Washing agents may have a negative effect on the long-term functionality of the product.•Using a brush during the cleaning process could break the module. Therefore, we do not recommend using a brush during the PCB cleaning process.Potting and Coating:•If the product is potted in the costumer application, the potting material might shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the component. Expansion could damage the components. We recommenda manual inspection after potting to avoid these effects.•Conformal coating may affect the product performance.Storage Conditions:• A storage of Würth Electronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment.•Do not expose the components to direct sunlight.•The storage conditions in the original packaging are defined according to DIN EN 61760-2.•If there is a moisture sensitive component, the storage condition in the original packaging is defined according to IPC/JEDEC-J-STD-033. It is also recommended to return the component to the original moisture proof bag and reseal the moisture proof bag again.•ESD prevention methods need to be followed for manual handling and processing by machinery.Handling:•Violation of the technical product specifications such as exceeding the nominal rated current, will void the warranty.•Violation of the technical product specifications such as but not limited to exceeding the absolute maximum ratings will void the conformance to regulatory requirements.•The Edge castellation is designed and made for prototyping, i.e. hand soldering purposes only.•Non-antenna modules must be equipped with a proper antenna having specific characteristics.•The applicable country regulations and specific environmental regulations must be observed.•Do not disassemble the product. Evidence of tampering will void the warranty.These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable. However, no responsibility is assumed for inaccuracies or incompleteness.All topics are described in a more detailed manner in the manual for each product.Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODGE001.0242019-07-18DIN ISO 2768-1mDESCRIPTIONWIRL-PRO9 Radio module 915MHzlow power ORDER CODE2607056291011BUSINESS UNIT STATUS PAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODGE001.0242019-07-18DIN ISO 2768-1mDESCRIPTIONWIRL-PRO9 Radio module 915MHzlow power ORDER CODE2607056291011BUSINESS UNIT STATUS PAGE。

密级状态：绝密()秘密()内部资料()公开(√)RK3066RK292X Android4.1SDK(GIT) MT5931&MT6622使用说明历史版本版本日期描述作者审核初始版本胡卫国V1.02012-12-20增加出错排查胡卫国V1.12012-12-31增加出错排查胡卫国V1.32013-01-05增加出错排查胡卫国V1.42013-03-12Android部分\device\rockchip\rkxxsdk\BoardConfig.mk修改如下：MT5931_WIFI_SUPPORT:=trueMT6622_BT_SUPPORT:=true//单WiFi不需要打开这个注意：修改后需要重新编译以下模块，mmm hardware/libhardware_legacy/-Bmmm system/netd/-Bmmm system/bluetooth/bluedroid/-Bmmm external/bluetooth/bluez/tools/-Bmmm frameworks/base/core/jni/-Bmmm packages/apps/Bluetooth/-B再做以下动作rm-rf out/target/product/rk30sdk/systemmakekernel部分WiFi部分修改：首先选择：System TypeWifi control func TypeEnable WiFi control function abstraction1)打开SDMMC1Device DriversMMC/SD/SDIO card support2)WiFi驱动部分Device DriversNetwork device supportWireless LAN注意：如果是单WiFi模块，选择”MediaTek MT5931WiFi”如果是WiFi与BT二合一模块，选择”MediaTek MT5931&MT6622WiFi Bluetooth Combo”3)WiFi协议部分（SDK上默认已经开启）Networking supportWirelessBT部分修改：1)打开串口支持(根据实际硬件接的串口选择)Device DriversCharacter devicesSerial drivers注意：RK3066上按如下配置软件上默认配置的是UART0,如果硬件上不是这个口，需要修改device/rockchip/rkxxsdk/init.rkxxboard.rc中的service mtk_hciattach/system/bin/hciattach-n-t10-s115200/dev/ttyS0mtk1500000noflow2)BT协议部分（SDK上默认已经开启）Networking supportBluetooth subsystem supportNetworking supportBluetooth subsystem supportBluetooth device drivers模块power控制中龙通K系列1)WiFiWiFi的控制脚有两个：#define RK30SDK_WIFI_GPIO_POWER_N RK30_PIN0_PD5//模块第2脚#define RK30SDK_WIFI_GPIO_RESET_N RK30_PIN0_PC7//模块第1脚具体在以下位置kernel\arch\arm\mach-rkxx\board-rkxx-sdk-sdmmc.c2928平台：先找到defined(CONFIG_ARCH_RK2928)3066平台：先找到defined(CONFIG_ARCH_RK30)31xx平台：arch/arm/mach-rk3188/board-rk3188-xxx-sdmmc-config.c2)BTBT的控制脚有三个power_gpio//模块第33脚reset_gpio//模块第6脚irq_gpio//模块第8脚32khz//模块第29脚(原先硬件给出参考电路不需要接，目前发现不接的话会导致机器长时间放置后BT无法使用的问题，因此需要接上)具体定义在kernel\arch\arm\mach-rk2928\board-rk2928-sdk.c其它二合一模块：例如M500WiFiWiFi的控制脚有两个：#define RK30SDK_WIFI_GPIO_POWER_N RK30_PIN0_PD5//模块第30脚#define RK30SDK_WIFI_GPIO_RESET_N RK30_PIN0_PC7//不需要控制，reset是与BT共用的，放在bt驱动的probe函数里控制BTBT的控制脚有三个power_gpio//模块第1脚reset_gpio//模块第22脚irq_gpio//模块第41脚常见问题排查WiFi部分：1.SDIO通信失败表现出的异常是WiFi打不开，kernel部分会出现以下logrk29_sdmmc_command_complete..2935...CMD5(arg=0x0),hoststate=1,errorTimes=1,errorStep=0x1e![sdio] rk29_sdmmc_command_complete..2935...CMD55(arg=0x0),hoststate=1,errorTimes=1,errorStep=0x1e![sdio] rk29_sdmmc_command_complete..2935...CMD55(arg=0x0),hoststate=1,errorTimes=1,errorStep=0x1e![sdio] rk29_sdmmc_command_complete..2935...CMD55(arg=0x0),hoststate=1,errorTimes=1,errorStep=0x1e![sdio] rk29_sdmmc_command_complete..2935...CMD55(arg=0x0),hoststate=1,errorTimes=1,errorStep=0x1e![sdio] rk29_sdmmc_command_complete..2935...CMD1(arg=0x0),hoststate=1,errorTimes=1,errorStep=0x1e![sdio]请确认一下1)WiFi的power与reset脚是否上电成功(高电平有效)2)确认一下32K RTC_CLK是否有供给上3)SDIO电平是否足够，是否需要上拉2.wpa_supplicant未更新表现出的异常是WiFi打不开或WiFi能打开，但是连接不上AP，请确认机器中以下文件是否已经更新(需要保证device/rockchip/rkxxsdk/wifi/mtk_wpa_supplicant_8/目录下的文件更新到out目录下)(可通过对比文件大小)system/bin/wpa_supplicantsystem/etc/wifi/wpa_supplicant.confsystem/lib/libwpa_client.so如果没有，直接删除rm-rf out/target/product/rkxxsdk/system再make3.机器休眠唤醒后WiFi异常休眠唤醒后，出现WiFi无法上网，在扫描列表里看不到扫描到的其它AP，只显示已保存的AP需要确认在休眠的时候，模块的电源(可能是PMU供),power,reset脚是否有断电，这个不能断电，需要常供。