下载文档原格式
Compact Stereo Amplifier 20 Watts RMS x 2 ChannelsModel #SLA-40Stellar LabsDivision of MCM Electronics650 Congress Park DriveCenterville, Ohio 45459© 2009 MCM, a Premier Farnell CompanySafety InformationThe lightning boltwithin a triangle is intended to alert theuser to the presence of un insulated dangerous voltage levels within the product’s enclosure. This voltage may be of sufficient magnitude to constitute an electric shock risk. To reduce the risk of electricshock, do not remove coverof this device. There are nouser serviceable partsinside. Refer servicing onlyto qualified servicepersonnel.The exclamation pointwithin a triangle isintended to alert theuser to importantoperating andmaintenance(servicing)instructions in theliteratureaccompanying theappliance.Safety Precautions• Read and retain these instructions• Follow all instructions and heed warnings• Do not use this device near water• If the surface becomes dirty, clean only with dry cloth, do not use solvents or thinners• Install in accordance with the manufacturer’s instructions• Do not block ventilation openings• Do not install near heat sources such as radiators, heat registers, stoves, or other devices that produce heat• Do not defeat the safety purpose of the grounded plug. This plug has twoblades and a third ground prong. The wide blade or third prong are provided for your safety. If the provided plug does not fit into your outlet, consult anelectrician for replacement of the obsolete outlet• Protect the power cord from being stressed at the plugs, conveniencereceptacles, and where they exit the amplifier• Only use accessories specified by the manufacturer• Unplug the device during lightning storms or when unused for an extended time• Refer all servicing to qualified personnel• This device must not be exposed to water in any way. No object filled withliquids should be placed on apparatusCongratulations on your purchase of thisStellar Labs SLA Series Stereo AmplifierThis amplifier was designed specifically for use in permanent audio installations, where high reliability and premium sound quality are a must. Highly rugged construction and high efficiency design make this amplifier perfect for continuous duty applications in situations were power will be left on for indefinite periods of time.This amplifier is warranted from defects for one year from the date of purchase. Should your amplifier require service, either within or beyond that warranty period, please contact your MCM Sales Representative.This unit includes a host of features, along with an impressive list of specifications, which are detailed over the next pages. Please take the time to read this document completely prior to installation of this product. Should you have questions regarding installation or operation of this unit, please contact the MCM Technical Support Department.Features•20W RMS stereo amplifier, bridgeable to 40W RMS mono•Highly efficient design (85%)•Extreme compact size•Rugged steel housing•Independent L/R gain control•Independent bass and treble control•Switchable limiter•RCA unbalanced line level inputs•Detachable screw terminal balanced inputs, mic/line switchable•Detachable screw terminal speaker outputs•Attached brackets for easy wall mountingSpecifications•Power Output: 20W x 2 Channels, both channels driven at 8ohms•Frequency Response: 50Hz ~ 18KHz•Total Harmonic Distortion (THD): 0.05%•Power requirements: 24VDC, AC adaptor supplied•Dimensions: 2.25" (H) x 7.75" (W) x 4.5" (D)•Weight: 2 lbs.Applications•Installation behind flat panel monitors to power local speakers•Kiosk and retail displays•Powering additional zones on an existing distributed audio system•Audio program material for digital signage installations•Classroom installations, especially where video projectors are usedConnections / Controls1.DC Power Input – Supplied AC adaptor provides 24VDC, 3A with100~240VAC, 50~60Hz input range.2.Power ON/OFF Selector – Turns amplifier power on or off. When on,the blue LED immediately to the right of this switch will illuminate.3.Speaker Output Connection – Detachable Phoenix style connectorsmay be removed from the amplifier for easy access. Screw typeterminals will accept up to 14AWG wire. Note the different labeling forstereo or bridged mono connection. Also, as this is a floating output,no speaker connections may be tied to chassis or earth ground.4.Balanced Input Connection – Allows connection of line level or miclevel source to the input of the amplifier. Detachable Phoenix styleconnectors may be removed from the amplifier for easy access andaccept up to 14AWG wire. While this connection is intended forbalanced use, unbalanced sources may also be used by strapping thelow signal (-) and chassis ground terminals together.5.Unbalanced Input Connection – Accepts standard line level signalfrom conventional consumer devices such as CD/DVD players,television monitors, tape decks and tuners. Note that stereo operationrequires connection to left and right inputs. Each amplifier channelprovides two line level input connections for convenience when usingas two independent mono amplifiers.6.Mic / Line Selector – Determines whether screw terminal inputsaccept Mic level (3mV) or Line level (150mV) signal level. If you are not sure of your devices signal level, first use Line level. If signal level is very low, set the output volume to the lowest setting and select the Mic position. Then slowly increase the Channel Level Controls.7.Left / Right Channel Level Controls – Independent controls setoutput level for the amplifier. When the amplifier is operating inbridged mono mode, only the right control is used.8.Bridged / Stereo Mode Selector – Allows the unit to operate as astereo amplifier, with two channels each capable of 20W RMS output, or as a single mono amplifier channel, with 40W RMS output.9.Limiter ON/OFF Selector – Engages or disengages the input signallimiter circuit for amplifier output protection. In the ON position, the amplifier will automatically limit high input signal levels, which willprevent the amplifier from distorting, and reduce potential harm to speakers. In the OFF position, the amplifier operates in normal mode.It should be noted that overall dynamic range will be reduced when the limiter is ON, thus being the tradeoff that occurs when this feature is utilized.10.Bass Control – This control adjusts low frequencies centered at100Hz, at a rate of ±10dB.11.Treble Control – This control adjusts high frequencies centered at10,000Hz, at a rate of ±10dB.MCM Custom Audio and Stellar Labs products are warranted, by MCM Electronics, against manufacturer defects for a period of one year from the original date of purchase. This warranty is limited to manufacturer defects, in either materials or workmanship. MCM Electronics, or any other worldwide divisions of Premier Farnell PLC, are not responsible for any consequential or inconsequential damage to any other component, structure or the cost of installation or removal of said items.For questions or specific information regarding warranty replacement or repair, contact:MCM Electronics800-543-4330。
视频图像信息共享平台安全加固项目系统测试报告目录1.1测试项目名称 (2)1.2项目说明 (2)1.3项目测试依据 (2)1.4项目系统测试 (2)1.4.1下一代防火墙网康NF-5000（1台） (2)1.4.2视频资源安全网关上海远哲VC-SS3200/V1.0（6台） (13)1.4.3“一机两用终端”管控系统北信源非法外联及客户端安全监控系统V6.6（含北信源杀毒软件V2.0）（1600个点） (15)1.4.4视频监控资源风险等级管控定制（1套） (19)1.4.5服务器华为RH2288 V3（2台） (20)1.4.6人像智能识别授权认证模块上海依图人像照片识别与比对系统V1.0（1套）201.4.7数据库安全防护系统（含数据库审计及漏洞修复功能）圣博润LDB-F10000（1台）201.4.8运维审计系统（堡垒机）网神SecFox-C3000-848X（1套） (27)1.4.9视频联网网关海康威视IVMS-8201E-VAG（1台） (30)1.4.10网络硬盘录像机海康威视DS-8608N-I8（1台） (31)1.4.11千兆三层交换机华为S5700-28P-LI-AC（1台） (33)1.4.12前端摄像机海康威视DS-GPZ22A4/E-LSWGD30（5台） (34)1.4.13光纤收发器烽火OL100CR-02A（5对） (35)1.4.14WIFI采集器海康威视DS-GPZ22A2/E-LSWGD(1台) (37)1.4.15卡口智能维护终端超智SWIT1010（5台） (38)1.4.16视频质量诊断服务器海康威视DS-IE6200-E/D（7台） (38)1.4.17与移动警务视频平台对接定制（1套） (38)1.4.18图形处理终端联想扬天A8000f（含显示器）（3台） (38)1.4.19移动图形处理终端联想ThinkPad L460（3台） (39)1.5项目测试地点 (39)1.6项目测试意见 (39)1.1测试项目名称项目名称：厅级视频图像信息共享平台安全加固项目1.2项目说明使用单位：厅信息中心承建单位：软件股份有限公司安装时间：厅级视频图像信息共享平台安全加固项目于2016年月份建成并投入使用。
INNO L U X DISPLAY CORPORATIONLCD MODULESPECIFICATIONCustomer:Model Name: AT056TN52 V.3SPEC NO.: A056-52-TT-31Date: 2009/03/25Version: 01■Preliminary Specification□Final SpecificationFor Customer’s AcceptanceApproved by CommentApproved by Reviewed by Prepared byJoe Lin 2009/03/31Jack HuangCharlie ChouJames Yu2009/03/30David Lee2009/03/26The copyright belongs to InnoLux. Any unauthorized use is prohibited.InnoLux copyright 2004All rights reserved,Copying forbidden.Record of RevisionVersion Revise Date Page ContentPre-spec.01 2009/03/25 Initial ReleaseContents:1.General Specifications (1)2.Pin Assignment (2)3.Operation Specifications (5)3.1.Absolute Maximum Ratings (5)3.2.Typical Operation Conditions (6)3.2.1 Typical Operation Conditions (6)3.2.2 Current Consumption (6)3.2.3 Backlight Driving Conditions (7)3.3.Power Sequence (8)3.4.Timing Characteristics (9)3.4.1.Timing Conditions (9)3.4.2.Timing Diagram (11)4.Optical Specifications (14)5.Reliability Test (18)6.General Precautions (19)6.1.Safety (19)6.2.Handling (19)6.3.Static Electricity (19)6.4.Storage (19)6.5.Cleaning (19)7.Mechanical Drawing (20)8.Package Drawing (21)8.1.Packaging Material Table (21)8.2.Packaging Quantity (21)8.3.Packaging Drawing (22)Page : 1/22 1.General SpecificationsNo. Item Specification Remark1 LCD size 5.6 inch(Diagonal)2 Driver element a-Si TFT active matrix3 Resolution 640 × (RGB) × 4804 Display mode Normally White, Transmissive5 Dot pitch 0.0588(W) × 0.1764(H) mm6 Active area 112.896 (W) × 84.672(H) mm7 Module size 126.5(W) × 100(H) × 5.7(D) mm Note 18 Surface treatment Anti-Glare9 Color arrangement RGB-stripe10 Interface Digital11 Backlight Power consumption0.930W12 Panel Power consumption 117mW13 Weight 132gNote 1: Refer to Mechanical Drawing.Page : 2/22 2.Pin AssignmentTFT LCD Panel Driving SectionFPC connector is used for the module electronics interface. The recommended model isFH12S-50S-0.5SH manufactured by HiRose.Pin No.Symbol I/O Function Remark1 V LED+P Power for LED backlight anode2 V LED+P Power for LED backlight anode3 V LED-P Power for LED backlight cathode4 V LED-P Power for LED backlight cathode5 GND P Power ground6 V COM I V COM input7 V CC P Digital power supply(+3.3V)8 MODE I DE or HV mode control Note 19 DE I Data Enable10 VS I Vsync signal input11 HS I Hsync signal input12 B7 I Blue data input (MSB)13 B6 I Blue data input14 B5 I Blue data input15 B4 I Blue data input16 B3 I Blue data input17 B2 I Blue data input18 B1 I Blue data input19 B0 I Blue data input(LSB)20 G7 I Green data input(MSB)21 G6 I Green data input22 G5 I Green data input23 G4 I Green data input24 G3 I Green data input25 G2 I Green data input26 G1 I Green data input27 G0 I Green data input(LSB)28 R7 I Red data input(MSB)29 R6 I Red data inputPage : 3/2230 R5 I Red data input31 R4 I Red data input32 R3 I Red data input33 R2 I Red data input34 R1 I Red data input35 R0 I Red data input(LSB)36 GND P Power ground37 DCLK I Sample clock38 GND P Power ground39 L/R I Select left to right scanning direction Note 2,340 U/D I Select up or down scanning direction Note 2,341 VGH I Positive power for scan driver42 VGL I Negative power for scan driver43 AV DD P Power supply for analog circuit44 RESET I Reset45 POL O Polarity select for the line inversion control signal46 V COM I V COM input47 NC - No Connector48 NC - No Connector49 NC - No Connector50 NC - No Connector Note:I: input, O: output t, P: Power , R: ReserveNote 1: DE Mode, Mode=”H”,HS floating and VS floating HV Mode, Mode=”L” and DE floatingNote 2: Selection of scanning modeSetting of scan control inputU/D L/RScanning direction GND V CC Up to down, left to right V CC GND Down to up, right to left GND GND Up to down, right to left V CC V CC Down to up, left to rightPage : 4/22 Note 3: Definition of scanning direction.Refer to the figure as below:Left RightUpDownPage : 5/22 3.Operation Specifications3.1. Absolute Maximum Ratings(Note 1)ValuesItem SymbolMin. Max.Unit RemarkV CC-0.3 6.5 VAVDD-0.3 6.5 VV GH-0.318 VV GL-150.3 V Power voltageV GH-V GL- 33 V Operation temperature T OP-2070 ℃Storage temperature T ST-3080 ℃Note 1: The absolute maximum rating values of the module should not be exceeded.Once exceeded absolute maximum rating values, the characteristics of themodule may not be recovered. Even in an extreme condition, may result inmodule permanently destroyed.Page : 6/22 3.2.Typical Operation Conditions3.2.1 Typical Operation ConditionsValuesItem SymbolUnit RemarkMin. Typ. Max.V CC 3.0 3.3 3.6 V Note 1AV DD 4.8 5.0 5.2 VPower voltageV GH14.3 15.0 15.7 VV GL-10.5-10.0-9.5VV CAC- 5.50 - VV COMV CDC0.72 0.92 1.12 VInput logic high voltage V IH0.7V CC- 1V CC VNote 2 Input logic low voltage V IL0 - 0.3V CC VNote 1: V CC setting should match the signals output voltage (refer to Note 2) of customer’s system board.Note 2: DCLK,DE, HS, VS, R0~ R7,G0~ G7,B0~ B7.3.2.2 Current Consumption(GND =0V)ValuesUnit Remark Item SymbolMin.Typ. Max.I GH- 120 240 uA V GH =+15VI GL- 130 260 uA V GL = -10V Current for DriverI CC- 10 15 mA V CC =3.3VI DD- 16 24 mA AV DD =5VPage : 7/223.2.3 Backlight Driving ConditionsValuesUnit Remark Item SymbolMin. Typ. Max.Voltage for LED Backlight V L8.4 9.3 10.5 V Note 1 Current for LED Backlight I L90 100 110 mALED life time - 20,000- - Hr Note 2Note 1: The Voltage for LED Backlight is defined at Ta=25℃ and I L =100mA.Note 2: The “LED life time” is defined as the module brightness decrease to 50% original brightness that the ambient temperature is 25℃ and I L =100mA. The LED lifetimecould be decreased if operating I L is lager than 100 mA.Page : 8/22 3.3. Power Sequence3.3.1 Power on:VGHB/LAVDDVCCDATAGNDVGLTT=0G/2Note:Data includes DE, VS ,HS,B0~B7,G0~G7,R0~R7,DCLK.VCC→VGL→VGH→Data→B/LB/L→Data→VGH→VGL→VCCPage : 9/22 3.4.Timing Characteristics3.4.1.Timing ConditionsInput/Output TimingValuesUnit. Remark Item SymbolMin.Typ. Max.PXLCLK clock time Tclk 33.339.7 - nsPXLCLK pulse duty Tcwh 40 50 60 % TclkDATA set-up time Tdsu 12 - - ns DATA to PXLCLK DATA hold time Tdhd 12 - - ns DATA to PXLCLK DE setup time Tesu 12 - - ns DE to PXLCLK VSYNC setup time Tvst 12 - - nsVSYNC hold time Tvhd 12 - - nsHSYNC setup time Thst 12 - - nsHSYNC hold time Thhd 12 - - nsHSYNC period time Th 22.9131.76- usHSYNC width Thwh 1 - - TclkVSYNC width Tvwh 1 - - ThHSYNC to CLKIN Thc - - 1 TclkDE Mode input Timing LimitationValuesUnit Remark DE ModeMin. Typ. Max.THC 48 160 765 tclkTHD 640 640 640 tclkTH 688 800 1405 tclk 1TH=1lineTVC 6 45 255 lineTVD 480 480 480 lineTV 486 525 735 line 1TV=1fieldPage : 10/22 HV Mode input Timing LimitationValuesUnit RemarkHV ModeMin. Typ. Max.Thwh - 10 - tclkThbp - 134 - tclkThfp - 16 - tclkTHD - 640 - tclkTH - 800 - tclk 1TH=1 lineTvwh - 2 - lineTvbp - 11 - lineTvfp - 32 - lineTVD - 480 - lineTV - 525 - line 1TV=1 fieldPage : 11/22 3.4.2.Timing DiagramFig.3-2 DE Mode Input TimingFig.3-3 HV Mode Input TimingPage : 14/22 4.Optical SpecificationsValuesItem Symbol ConditionMin.Typ.Max.Unit RemarkθLΦ=180°(9 o’clock)60 70 -θRΦ=0°(3 o’clock) 60 70 -θTΦ=90°(12 o’clock)40 50 -Viewing angle(CR≥10)θBΦ=270°(6 o’clock)60 70 -degree Note 1T ON- 10 20 msec Note 3 Response timeT OFF-1530msec Note 3 Contrast ratio CR 400500-- Note 4W X 0.260.310.36-Color chromaticityW Y0.280.330.38-Note 2Note 5Note 6 Luminance L 150200- cd/m² Note 6 Luminance uniformity Y UNormalθ=Φ=0°7075-% Note 6,7 Test Conditions:1.V CC=3.3V, I L=100mA, the ambient temperature is 25.℃2.The test systems refer to Note 2.Page : 15/22Note 1: Definition of viewing angle rangeFig. 4-1 Definition of viewing angleNote 2: Definition of optical measurement system.The optical characteristics should be measured in dark room. After 30 minutes operation, the optical properties are measured at the center point of the LCD screen. (Response time is measured by Photo detector TOPCON BM-7, other items are measured by BM-5A/Field of view: 1° /Height: 500mm.)Fig. 4-2 Optical measurement system setupNormal line θ=Φ=0°Normal line θ=Φ=0°Photo detectorΦ=90°12 o’clock directionΦ=270°6 o’clock directionΦ=0°Φ=180°Active Area500mmLCD PanelΦ=90°12 o’clock directionΦ=270°6 o’clock directionΦ=0°Φ=180°Active Area θL θTθBθRNote 3: Definition of Response timeThe response time is defined as the LCD optical switching time interval between“White” state and “Black” state. Rise time (T ON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (T OFF) is the timebetween photo detector output intensity changed from 10% to 90%.Fig. 4-3 Definition of response timeNote 4: Definition of contrast ratiostateBlack""theonisLCDwhenmeasuredLuminancestateWhite""theonisLCDwhenmeasuredLuminance=(CR)ratioContrastNote 5: Definition of color chromaticity (CIE1931)Color coordinates measured at center point of LCD.Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel. The LED driving condition is I L=100mA .100%90%10%0%Photodetectoroutput(Relativevalue)ONTWhite (TFT OFF)Black (TFT ON)White (TFT OFF)Note 7:Definition of Luminance UniformityActive area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every measuring point is placed at the center of each measuring area.maxminBB(Yu)UniformityLuminance=L-------Active area length W----- Active area widthWW/3W/3W/6L/3L/3L/6LFig. 4-4 Definition of measuring pointsB max: The measured maximum luminance of all measurement position.B min: The measured minimum luminance of all measurement position.5.Reliability Test(Note3)Item Test Conditions Remark High Temperature Storage Ta = 80℃240 hrs Note 1, 4 Low Temperature Storage Ta = -30240hrs℃Note 1, 4High Temperature Operation Ts = 70240hrs℃Note 2, 4Low Temperature Operation Ta = -20240hrs℃Note 1, 4Operate at High Temperature and Humidity +40, 90%RH240 hrs℃Note 4Thermal Shock -30/30 min ~ +℃80/30 min for a total 100℃cycles, Start with cold temperature and endwith high temperatureNote 4Vibration Test Frequency range:10~55Hz Stroke:1.5mmSweep:10Hz~55Hz~10Hz2 hours for each direction of X. Y. Z.(6 hours for total)Mechanical Shock 100G 6ms,±X, ±Y, ±Z 3 times for each directionPackage Vibration Test Random Vibration :0.015G*G/Hz from 5-200HZ, -6dB/Octave from 200-500HZ2 hours for each direction of X. Y. Z.(6 hours for total)Package Drop Test Height:60 cm1 corner, 3 edges, 6 surfacesElectro Static Discharge ± 2KV, Human Body Mode, 100pF/1500ΩNote 1: Ta is the ambient temperature of samples.Note 2: Ts is the temperature of panel’s surface.Note 3: In the standard condition, there shall be no practical problem that may affect the display function. After the reliability test, the product only guaranteesoperation, but doesn't guarantee all the cosmetic specification.Note 4: Before cosmetic and function tests , the product must have enough recovery time, at least 2 hours at room temperature.6.General Precautions6.1.SafetyLiquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your skin or clothes, wash it off immediately by using soap and water.6.2.Handling1.The LCD panel is plate glass. Do not subject the panel to mechanical shock or toexcessive force on its surface.2.The polarizer attached to the display is easily damaged. Please handle it carefullyto avoid scratch or other damages.3.To avoid contamination on the display surface, do not touch the module surfacewith bare hands.4.Keep a space so that the LCD panels do not touch other components.5.Put cover board such as acrylic board on the surface of LCD panel to protect panelfrom damages.6.Transparent electrodes may be disconnected if you use the LCD panel underenvironmental conditions where the condensation of dew occurs.7.Do not leave module in direct sunlight to avoid malfunction of the ICs.6.3.Static Electricity1.Be sure to ground module before turning on power or operating module.2.Do not apply voltage which exceeds the absolute maximum rating value.6.4.Storage℃1.Store the module in a dark room where must keep at +25±10 and 65%RH orless.2.Do not store the module in surroundings containing organic solvent or corrosivegas.3.Store the module in an anti-electrostatic container or bag.6.5.Cleaning1.Do not wipe the polarizer with dry cloth. It might cause scratch.2.Only use a soft sloth with IPA to wipe the polarizer, other chemicals mightpermanent damage to the polarizer.Page : 20/22 7.Mechanical DrawingPage : 21/22 8.Package Drawing8.1.Packaging Material TableNo.ItemModel(Material)Dimensions(mm)UnitWeight(kg)Quantity Remark1 LCMModuleAT056TN52 V.3 126.5 × 100 × 5.7 0.132 60pcs2 Partition B Corrugatedpaper105 × 349 0.031 8pcs3 CorrugatedBoardB Corrugatedpaper510 × 350 0.074 2pcs4 PartitionPaperBC Corrugatedpaper512 × 226 × 349 1.000 1set5 Dust-ProofBagPE 700 × 530 0.060 1pcs6 A/S Bag PE 170 × 110 × 0.2 0.002 60pcs7 Carton Corrugated paper530 × 355 × 255 0.810 1 pcs8 Total Weight10.306 ± 5% kg8.2.Packaging QuantityTotal LCM quantity in Carton: no. of Partition 4 Rows x quantity per Row 15= 60Page : 22/22 8.3. Packaging Drawing。
产品承认书SPECIFICATION FOR APPROVAL客户名称（CUSTOMER）：客户料号（PART NO.）：客户品名（DESCRIPTION）：品名（DESCRIPTION）：日期（DATE）：2010-01-08目录目录 (2)变更说明 (3)1.适用范围 (3)2.产品功能描述 (3)3.工作环境 (3)4.保存环境 (3)5.产品规格 (3)6.电气参数 (10)7.电气回路 (11)8.可信赖性试验 (12)9.出货检验水准 (12)变更说明版本发行日期修改内容备注V12010-1-8初次修订购买时注明点屏型号及转换方式1.适用范围本标准适用于针对工控主板LVSD/TTL信号点：AT050TN22V.1,AT056TN52V.2,AT070TN92，AT080TN52，EJ080NA-05A/HSD070IDW1-D，AT070TN94,A104SN01，LSA40AT9001等中小尺寸信号转换主板点屏功能。
2.产品功能描述2.1TTL 或LVDS信号可选输入2.2TCON 板带背光驱动电路2.3可以驱动640*480800*480800*600的多款液晶模组3.工作环境4.1工作温度：-20℃～+70℃4.2工作湿度：90%RH（不可有结露）4.保存环境5.1保存温度:-20℃～+80℃5.2保存湿度:90%RH（不可有结露）5.产品规格5.1产品外形结构（单位产品外形结构（单位:mm :mm :mm））：成品板（含元件厚度4.50mm。
5.2产品接口定义:22G4绿色信号23G3绿色信号24GND 地25G2绿色信号26G1绿色信号27G0绿色信号28GND 地29R5红色信号30R4红色信号31R3红色信号32GND 地33R2红色信号34R1红色信号35R0红色信号36GND 地37GND-DCLK 地和时钟可选Note638DCLK-GND 时钟和地可选Note739GND 地40GND 地备注更改说明Note1通过R153R 的0R 电阻实现5V和地之间的转换也可作为空脚（焊上R153的0R 电阻此管脚为5V ，不焊为空脚，R153上端横跨0R 电阻到R151上端此管脚为地）常规为空脚Note2同上（1脚2脚为导通脚）Note3常规为不带控制（要控制需把R106电阻去掉R104位置加0R 电阻，更改后高电平为开）Note4通过R152的0R 电阻实现3.3V 和地之间的转换也可做为空脚（焊上R152的0R 电阻此管脚为3.3V ，R152的0R 电阻的下端横一个0R 电阻到R151电阻的上端此管脚为地）常规为空脚Note5同上（5脚6脚为导通脚）Note6当R156焊0R 电阻R157空时37脚为地。
Product SpecificationModel: KM39E5-CM-01Customer Approved byGuangdong Kaimy Electric Co.,LtdApproved by Checked by Prepared byINTRODUCTION• WARRANTYGuangdong Kaimy Electric Co. Ltd. (hereinafter called "Kaimy") warrants that this product meetsthe product specifications set forth in this document. If this product under normal operation is found to benon-conforming to the product specifications, and such non-conformance is promptly notified to Kaimy within one (1)year after the delivery date, and further such non-conformance is solely attributable to Kaimy, Kaimy shall repair the non-conforming product or replace it with a conforming one, free of charge. However, this warranty does not apply to any non-conformance that can be found easily by incoming inspections or those resulting from any one of the following：1) Unauthorized or improper repair, maintenance or modification2) Operation or use against specifications, instructions or warnings given by Kaimy3) Any other causes attributable to customerIn case Kaimy repairs or replaces a product after the one (l)-year warranty period, Kaimy shall be entitled to charge for such repair or replacement. Those replaced parts shall be covered with six (6)-month warranty period from the replacement day. Non-conforming products may be replaced with substitutes instead of repair when the manufacture of this product has been terminated.EXCEPT AS EXPRESSLY SET FORTH HEREIN, Kaimy DISCLAIMS ANY WARRANTIES, EXPRESS ORIMPLIED, INCLUDING BUT NOT LIMITED TO MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND DISCLAIMS ANY REMEDIES.• MAINTENANCEThe specifications of maintenance parts may be partially changed within equivalent quality or better. In this product, Kaimy will not accept to maintain for only mounting parts on circuit board (e.g. connector, fuse, capacitor,resistor, etc.) and only backlight conformation parts (e.g. reflector sheet, light guide plate, etc.).If Kaimy is planning discontinuation for this product, Kaimy shall inform it to customers in six (6)-months advance from the issued date of official agreements. In addition, after product discontinuation, Kaimy may replace substitutes instead of maintenance parts with whole product.• CHANGE CONTROLFor the purpose of product improvement, this product design may be changed for specifications, appearance, parts,circuits and so on. In case a design change is affected on the product specifications, Kaimy shall inform it to customers in advance.• HANDLING OF DOUBTFUL POINTSAny question arising out of, or in connection with, this SPECIFICATION or any matter not stipulated herein will be settled each time upon consultation between both parties.Version A0Page 24Record of RevisionsVersion Revise Date Page ContentsA0 2013-7-25 24 KM39E5-CM-01 version 1.0 specification was first issued.Version A0Page 24CONTENTS INTRODUCTION..................................... .. (2)RECORD OF REVISION (3)CONTENTS (4)1. OUTLINE (5)1.1 STRUCTURE AND PRINCIPLE (5)1.2 APPLICATIONS (5)1.3 FEATURES (5)2. GENERAL SPECIFICATIONS (6)3. ABSOLUTE MAXIMUM RATINGS (7)4. MECHANICAL SPECIFICATIONS (8)5. ELECTRICAL CHARACTERISTICS (9)6. INTERFACE PIN CONNECTION (12)7. INTERFACE TIMING (17)8. INPUT SIGNALS, BASIC DISPLAY COLORS &GRAY SCALE OF COLORS (20)9. SIGNAL TIMING WA VEFORMS OF INTERFACE SIGNAL (20)10. OPTICS SPECIFICATIONS (21)11.OUTDRAWING (23)1. OUTLINEVersion A0Page 241.1 STRUCTURE AND PRINCIPLEKM39E5-CM-01 module is composed of the amorphous silicon thin film transistor liquid crystal display (a-Si TFT LCD) panel structure with driver LSIs for driving the TFT (Thin Film Transistor) array and a backlight. The a-Si TFT LCD panel structure is injected liquid crystal material into a narrow gap between the TFT array glass substrate and a color-filter glass substrate. Color (Red, Green, Blue) data signals from a host system (e.g. PC, signal generator, etc.) are modulated into best form for active matrix system by a signal processing board, and sent to the driver LSIs which drive the individual TFT arrays. The TFT array as an electro-optical switch regulates the amount of transmitted light from the backlight assembly, when it is controlled by data signals. Color images are created by regulating the amount of transmitted light through the TFT array of red, green and blue dots.1.2 APPLICATIONS• Monitor for PC& Workstation Use• Monitors for Process Controller1.3 FEATURES• a-Si TFT active matrix• 2ch-LVDS interface• 6-bit (Hi-FRC) color depth, 16.7 millions colors (6bit/color)• Resolution WXGA+:(1,920×1,080 pixels)• Wide viewing angle:176°(Horizontal); 176° (Vertical)• High contrast ratio: 3000:1(typ)• Module size: 895.6(H) ×526(V) ×65.9 (D)mm• High response time (Ton+Toff=8.5 ms）• RoHS compliance2. GENERAL SPECIFICATIONSVersion A0Page 24 Display area 895.6 (H) x 526(V)mm (typ.),,Diagonal size of display 39 inchesDisplay color 16.7M colors (6bit/color)Pixel 1920 (H) x 1080(V) pixelsPixel arrangement RGB vertical stripePixel pitch 0.17675 (H) x 0.53025(V) mmModule size 895.6(H) ×526(V) ×65.9(D)mm Contrast ratio 3000:1(typ.)Viewing angle 176°/176° (typ.)Response time 8.5 ms (typ.)Luminance 270cd/m2 (typ.)Display Mode Transmissive mode / Normally white Surface Treatment Anti GlareBacklight consumption 42W (typ.)3. ABSOLUTE MAXIMUM RATINGSVersion A0Page 24Version A0Page 244. MECHANICAL SPECIFICATIONSItem Min Typ Max Unit NoteModuleHorizontal(H) 894.6 895.6 896.6 mm (1) SizeVertical(V) 525 526 527 mmDepth(D) 65.966.9 mmWeight TBD TBD TBD kg5. ELECTRICAL CHARACTERISTICSVersion A0Page 24Document No. KM39E5-CM-01 Version A0Page 24Document No. KM39E5-CM-01Version A0Page 245.2 Driving for backlight LEDItem SymbolV alueUnit NoteDuty100% Min. Typ. Max.LED Forward Current If 560 600 mALED Forward V oltage Vf 70 7580 VPower Disssipation P D42 WNote (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation Note(2): The backlight of this product is made up of 4 LED light bar.Note (3) Specified values are for input pin of LED light bar at Ta=25±2 ℃Version A0Page 24 6. INTERFACE PIN CONNECTIONVersion A0 Page 24Document No. KM39E5-CM-01 Version A0Page 246.2 LED light barCN201: PH2.0-8P & PH-TAdaptable connector:Pin No. SignalnameFunction1 V+ “+”input terminal for LED light bar (Cable color :Red)2 V- “-”input terminal for LED light bar (Cable color :Black)7 V+ “+”input terminal for LED light bar (Cable color :Red)8 V- “-”input terminal for LED light bar (Cable color :Black)Document No. KM215H1-CM-11Version A07. INTERFACE TIMINGPage 24Page 24Page 24Document No. KM215H1-CM-11Version A0Page 248. INPUT SIGNALS, BASIC DISPLAY COLORS &GRAY SCALE OF COLORS9. SIGNAL TIMING WA VEFORMS OF INTERFACE SIGNAL9.1 Sync Timing WaveformsDocument No.KM215H1-CM-11Version A0 Page2410. OPTICAL SPECIFICATIONS10.1 OVERVIEWThe test of Optical specifications shall be measured in a dark room (ambient luminance <1 lux andtemperature = 25+/-2℃) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-7) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ direction (“upward”), θØ=180(= θ9) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 30 minutes warm-up period. VDD shall be 5.0V +/-10% at 25℃. Optimum viewing angle direction is 6 ’clock. 10.2 OPTICAL SPECIFICATIONS[VDD = 5.0V , Frame rate = 60Hz, Clock = 74.25MHz, IBL= 240 mA, Ta =25±2 ℃]Item Symbol Condition Min. Typ. Max. UnitNoteColor Chromaticity Red Rx θ=0°, (CenterNormal Viewing Angle) With RFD module Typ-0.03 0.643 Typ+0.03 - (7) Ry 0.329 - Green Gx 0.279 - Gy 0.589 - Blue Bx 0.133 - By 0.111- White Wx 0.311 - Wy 0.349- Luminance of White Y W 250 270 cd/m2 (5)Contrast Ratio CR 3000 - (3) ResponseTime Rising Tr- 8.5 16 ms (8) FallingTf-- 8.5 16 ms(8)Viewing AngleHorizontal Θ3CR ≥10 With RFD Module88 -Deg.(2)Θ9 88 - V erticalΘ12 88 - Θ688-Note (1) :The value in upper table are based on BLU provided by Kaimy.Note (2): Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizo ntal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface. Note (3) :surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. Luminance when displaying a white rasterLuminance when displaying a black rasterDocument No. KM215H1-CM-11Version A0 Page24Note (4):Luminance of LCD module shall be made without signal input. Cell transmittance is defined mathematically, BLU provided by Kaimy.Note (5):Center Luminance of white is defined as the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display.Note (6):The White luminance uniformity on LCD surface is then expressed as :ΔY = ( Minimum Luminance of 9points / Maximum Luminance of 9points ) * 100 (See FIGURE 2 shown in Appendix).Note (7):The color chromaticity coordinates specified in above Table shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel with BLU provided by Kaimy.Note (8):The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Td, and 90% to 10% is Tr. 10.3 APPENDIXFigure 1. Measurement Set UpFigure 2. White Luminance and Uniformity Measurement Locations (9 points)11.OUTDRAWINGDocument No. KM215H1-CM-11Version A0Page 24Document No. KM215H1-CM-11 Version A0Page 24。
12X Internal Blu-ray Writer bd330iEntertainment• Enjoy your favorite Blu-ray and DVD movies on your PC• Experience exceptional picture quality and extraordinarydigital sound• Enjoy Blu-ray and DVD movie bonus features• Create your own Blu-ray Disc from your high definitionfootage• Watch 3D content on your PC. Supported display devices and viewing glasses are requiredTechnology• Blu-ray technology delivers high definition content and large storage capacity• Archive up to 50GB of data on a double layer BD media• SATA interface delivers great performance and flexibility Versatile• Easily upgrade your PC with the latest Blu-ray technology • Capable of writing BD-R SL/DL, BD-RE SL/DL, DVD±R, DVD±R DL, DVD±RW, DVD-RAM, and CD-R/RW media• Record video onto BD or DVD with your PC and enjoy it on a big screen TV• Back up critical files on BD, DVD and CD mediaBonus Features• Use the Cyberlink Media Suite to manage your multimedia content - play movies, edit and playback video, createslideshows, and back up music and data• Surprise your family and friends with slideshows and home movies, digitally preserved on DVD or CD and ready forplaybackIn today’s growing market for high definition content, the HP 12X Internal Blu-ray Writer bd330i is the ideal solution for Blu-ray Disc (BD) authoring. Use the HP bd330i to experience exceptional picture and sound quality from Blu-ray videos. This all-in-one solution not only writes and plays back high-definition BD content, but it also lets you preserve, edit, back up, and share videos, photos, and documents. Enjoy watching 3D content on your PC.The HP 12X Internal Blu-ray Writer can record on BD, DVD, and CD media. The HP bd330i comes bundled with a free 30-day trial (from date of installation) of CyberLink Media Suite, aneasy-to-use software, which lets you organize, play, edit, burnand share your digital content.Drive PerformanceMinimum System RequirementsCompatibilityEnvironmentSoftware IncludedWarranty Box Contents• Write speed: BD-R SL up to 12X; BD-R DL up to 8X; BD-RE SL/DL up to 2X; DVD+R up to 16X (CAV); DVD+RW up to 8X (ZCLV); DVD-R up to 16X(CAV); DVD-RW up to 6X (ZCLV); DVD+R Double Layer up to 8X (ZCLV); DVD-R Dual Layer up to 8X (ZCLV); DVD-RAM up to 12X (PCAV); CD-R up to 48x (CAV); CD-RW up to 24x (ZCLV)• Read speed:BD SL up to 8X (CAV); BD DL up to 6X (CAV); DVD-ROM up to 16X (CAV); CD-ROM up to 48x (CAV)• Sustained transfer: 1x CD = 150 KB/s (data mode 1); 1X DVD = 1350 KB/s; 1X BD = 4500 KB/s • Access time: BD 250 ms; DVD 150 ms; CD 150 ms (typical)• Mean time between failures (MTBF): 60,000 POH at 25% duty cycle in room temperature• 3.0 GHz Intel Pentium-D processor or equivalent or higher • 1 GB RAM or higher• High Definition Content Protection (HDCP) capable graphic card with minimum 256 MB RAM, and support for 1900 x 1200 resolution, and 32-bit color • HDCP capable monitor or TV for high-definition digital output• Minimum hard disk space requirements: 1 GB free for included software installation,10 GB free for DVD video disc creation (18 GB free for double-layer), and 60 GB free for BD video creation • Internet connectivity recommended for software updates• Operating system compatibility: Microsoft Windows ® Vista/7/8 (32 bit or 64 bit) or Windows XP SP3• Available SATA port, and SATA power cable• Windows ® 7 or Windows ® 8 is required for 3D content playback. 3D supported display devices and viewing glasses are also required.• Device write media compatibility: BD-R SL/DL, BD-RE SL/DL, CD-R, CD-RW, DVD+R, DVD+R DL, DVD+RW, DVD-R, DVD-R DL, DVD-RW, 4.7 GB single-sided/9.4 GB double-sided DVD-RAM (2.6 GB single-sided/5.2 GB double-sided media not supported) media• Device read media compatibility: BD-R/RE SL/DL, BD-ROM SL/DL, DVD-ROM, DVD+R, DVD+R DL, DVD+RW, DVD-R, DVD-R DL, DVD-RW, DVD-RAM, DVD-Video, CD-R, CD-RW, CD-DA, CD Extra, CD-ROM (Mode 1 - Yellow Book), CD-ROM/XA & CD-I Ready (Mode 2/Form 2 – Green Book), Photo-CD (single and multi-session), VCD, CD-Text• Operating temperature: 5° to 50° C (41° to 122° F)• Storage temperature: -40° to 65° C (-40° to 149° F)• Operating humidity: 15% ~ 80% RH (Non-condensing)• Storage humidity: 15% ~ 90% RH (Non-condensing)• Power requirements: +5V+/-5%; +12V+/-10%• 1-year limited hardware warranty from date of purchase.• Internal SATA Blu-ray Disc , DVD/CD Writer drive • Software CD, including electronic User’s Guide• Quick Start guide and warranty statement• SATA data cable • Installation screws• Cyberlink Media Solution 10 with 3D Support (free 30-day trial version from date of installation)Questions about the HP bd330i?Look us up online at Hewlett-Packard Company, Palo Alto, CA 94304Manufactured and distributed under license from Hewlett-Packard. Actual product image may vary from image shown. All specifications are subject to change without notice.HP shall not be liable for technical or editorial errors or omissions contained herein.Microsoft, Windows, XP, Vista, and Windows 7 are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.All other brand and product names are trademarks, registered trademarks or service marks of their respective holders.12X Internal Blu-ray Writerbd330i。
R e l e a s e d a t e : 2017-02-10 14:47D a t e o f i s s u e : 2017-02-10202096_e n g .x m lRefer to “General Notes Relating to Pepperl+Fuchs Product Information”.R e le a s e d a t e : 2017-02-10 14:47D a t e of i s s u e : 2017-02-10202096_e ng .x m lRefer to “General Notes Relating to Pepperl+Fuchs Product Information”.Technical dataGeneral specifications Effective detection range 0.2 ... 8 m Light source IREDLight typemodulated infrared light , 850 nm Protection field height see Table 1, max. 2400 mmOperating mode Startup/restart disable, deactivateable Optical resolution 90 mm Angle of divergence 5 °Ambient light limit Not sensitive to ambient light in accordance with EN 61496-2UL File NumberE215245Functional safety related parameters Safety Integrity Level (SIL) SIL 1Performance level (PL) PL c Category Cat. 2Mission Time (T M ) 20 a PFH d Depending on the protection field height; see Manual Type 2Indicators/operating means Operation indicator green: Power onFunction indicator Green: OSSD ON , Red: OSSD OFFStatus indicator Transmitter unit: LED yellow: Mode, test or errorReceiver: LED yellow: Start readiness, function reserve or errorElectrical specifications Operating voltageU B 24 V DC (-20%, +30%) ; Power supply with safe isolation: 24 V DC No-load supply current I 0Transmitter unit:≤ 150 mAReceiver: ≤ 150 mA (outputs open)Protection class III , IEC 61140Power consumptionP 0Transmitter unit: 5 W Receiver: 15 W Input 1Input type Transmitter unit test Input formatBreak contact Switching voltage 24 V DC Input current 5 mAInput 2Input type Transmitter unit, mode A/B Function Beam Code A: open or 0 V Beam Code B: 24 V DC, 5 mA Input 3Input type Receiver unit relay monitor Input formatBreak contact Switching voltage 24 V DC Input current 5 mAInput 4Input type Receiver unit, start release Input format Break contact Input current 5 mAInput 5Input type Receiver unit, mode A/B (see transmitter unit, mode A/B)OutputResponse time see Table 1, max. 17 msOutput 1Output type Receiver unit OSSDSignal output PNP semiconductor , monitored for short and cross circuits Switching voltage ON: U B - 2 V; OFF: < 1 V Switching current ON: max. 0.1 A; OFF: < 5 µAOutput 2Output type Receiver signal output start readinessSignal output PNP-semiconductor, short-circuit protected, 0.1A Ambient conditions Ambient temperature -30 ... 60 °C (-22 ... 140 °F)Storage temperature -30 ... 70 °C (-22 ... 158 °F)Relative humidity max. 95 %, not condensingMechanical specifications Housing length L see table 2Degree of protection IP65 , For indoor use onlyConnectionTransmitter unit: 4-pin, M12 x 1 connector Receiver: 8-pin, M12 x 1 connector Cable cross section min. 0.25 mm 2 Max. cable length 50m MaterialHousing extruded aluminum section , Silver anodized Optical face Plastic pane , Transparent polycarbonate Masssee table 2R e l e a s e d a t e : 2017-02-10 14:47D a t e o f i s s u e : 2017-02-10202096_e n g .x m lRefer to “General Notes Relating to Pepperl+Fuchs Product Information”.Table 1 - Response time:Table 2 - Total length and weight:Mounting aid OMH-SLCT-01Press & Release q u ick clamp and adj u stment systemOMH-SLCT-02Attachment aid for Press &Release q u ick clamp and adj u stment systemOMH-SLCT-03Mo u nting aid w ith fixed bearing (long) for mo u nting or u sed to connect 2 light gids OMH-SLCT-04Mo u nting aid w ith loose bearing (narro w )Other accessories TR 14/30/50/60Test rod for 14mm, 30mm, 50mm or 60mm resol u tionAA SLCT-01Alignment aid (box le v el to snapped into the lateral groo v es), Angle error: < 1°Connecting cable V1-G-BK2M-PUR-U:Cable, M12, 4-pin, 2m, UL-connector V1-G-BK5M-PUR-U:Cable, M12, 4-pin, 5m, UL-connector V1-G-BK10M-PUR-U:Cable, M12, 4-pin, 10m, UL-connector V19-G-BK2M-PUR-U:Cable, M12, 8-pin, 2m, UL-connector V19-G-BK5M-PUR-U:Cable, M12, 8-pin, 5m, UL-connector V19-G-BK10M-PUR-U:Cable, M12, 8-pin, 10m, UL-connectorinstructions have to be observed where applicable. For information see .Compliance with standards and directi-vesDirective conformity Machinery Directive 2006/42/EC EN ISO 13849-1:2008 ; EN 61496-1:2013EMC Directive 2004/108/EC EN 61000-6-3:2007+A1:2010 ; EN 61000-6-4:2007+A1:2011Standard conformity Functional safety IEC 61508:2010 part 1-4Standards IEC 61496-2:2006Approvals and certificates CE conformity CEUL approval cULus ListedCCC approval CCC approval / marking not required for products rated ≤36 V TÜV approvalTÜVAdditional informationHeight of the protected area[mm]Response time[ms]30086001090011120012150014180015210016240017Height of the protected area[mm]Total length oftransmitter/recei v er u nit[mm]Weight oftransmitter/recei v er u nit[g]30041925060071943090010196001200131976015001625940180019251100210022251270240025251440System accessoriesR e l e a s e d a t e : 2017-02-10 14:47D a t e o f i s s u e : 2017-02-10202096_e n g .x m lRefer to “General Notes Relating to Pepperl+Fuchs Product Information”.。
CONTINUED > 2.5-Inch HDD pg 2CONTINUED > 2.5-Inch SSD pg 3New Seagate Model Number Key, EnterpriseST 500 NM 123 1BRANDCAPACITYSEGMENTATTRIBUTESGENERATION2 letters ST = Seagate MX = Maxtor2 to 4 digits 500 = 500GB 1000 = 1000GBCapacities >9999GB:10 = 10TB 15 = 15TB2 lettersMM = Mission-Critical, 2.5-Inch, 10K MX = Mission-Critical, 2.5-Inch, 15K NM = Nearline, 3.5-Inch NX = Nearline, 2.5-Inch FM = SSD Mainstream FX = SSD Performance3 digits, non-intelligentVaries as needed, for example:Interface RPM Cache SED1 digit, intelligent 1 = 1st Generation2 = 2nd Generation3 = 3rd GenerationSeagate Partner Program MembersVisit the Sales Tools section to access the latest product roadmap, end-of-life schedule and product information. DistributorsEMEA SPP Support00-800-6890-8282US Sales Support1-800-SEAGATE or 1-405-324-4700Visit for more information or call 1-800-SEAGATE (1-800-732-4283) © 2012 Seagate Technology LLC. All rights reserved. Printed in USA. Seagate, Seagate Technology and the Wave logo are registered trademarksof Seagate Technology LLC in the United States and/or other countries. Cheetah, Constellation.2, Pulsar, Pulsar.2 and Savvio are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. The FIPS logo is a certification mark of NIST, which does not imply product endorsement by NIST, the U.S., or Canadian governments. All other trademarks or registered trademarks are the property of their respective owners. When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer’s operating system may use a different standard of measurement and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage. Actual data rates may vary depending on operating environment and other factors. The export or re-export of hardware or software containing encryption may be regulated by the U.S. Department of Commerce, Bureau of Industry and Security (for more information, visit ). Seagate reserves the right to change, without notice, product offerings or specifications. QR501.17-1210US, October 20121 One gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes when referring to hard drive capacity.2 Self-Encrypting Drives (SED) and FIPS 140-2 Validated drives are not available in all models or countries. May require TCG-compliant host or controller support.3 See FIPS 140-2 Level 2 Certificate at /groups/STM/cmvp/documents/140-1/1401val2010.htm#12994 Data provided is based on format at 512 bytes.View a brief training presentation on how our model number format has changed at /seagate/ModelNumber。
PC401s Features(Unit :mm )s Outline DimensionsCompact, Surface Mount Type OPIC PhotocouplerFHL represents forward current when output gose from high to low.FLH represents forward current when output goes from low to high.FHL /I FLH .t r =Z O OH %020010015010050025*********Ambient temperature T a (˚C )P o w e r d i s s i p a t i o n P O , P t o t (m W )1020605040300-2525507510085F (m A )Ambient temperature T a (˚C )F o r w a r d c u r r e n t I Fig. 2 Power Dissipation vs. Ambient Temperature-25P tot P O*3 I *4 I *5 Hysteresis stands for I *6 Test circuit for response time is shown below.125102050100200500F (m A )Fig. 3 Forward Current vs. Forward VoltageFig. 4 Relative Threshold Input Current vs. Supply Voltage00.4R e l a t i v e t h r e s h o l d i n p u t c u r r e n t0.60.81.6-1.41.21.00.2Ambient temperature T a (˚C )Low level output current IOL (mA )F o r w a r d c u r r e n t I 0.2L o w l e v e l o u t p u t v o l t a g e V O L (V )0.30.5-25025501000.100.47516mA5mAAmbient temperature T a (˚C )Fig. 7 Low Level Output Voltage vs. Ambient Temperature0.100.20.511010602520304050Fig. 8 High Level Output Current vs.Forward current IF (mA )Forward CurrentI OL =30mAV CC =5V I F =0V CC =5VT a =25˚CH i g h l e v e l o u t p u t c u r r e n t I O H (µA )0.050.5H i g h l e v e l o u t p u t c u r r e n t I O H (µA )12-252550751000.20.1Fig. 9 High Level Output Current vs. Ambient Temperature012948181254367810146225˚C 85˚C 16 Supply voltage V CC (V )-25˚C C C (m A )Forward current I F (mA )0123561020304060504 (µs )Fig.11 Propagation Delay Time vs. Forward Current00.10.20.512510200.20.30.40.50.6L (k Ω)R i s e t i m e , f a l l t i m e (µs )Fig.12 Rise Time, Fall Time vs.P r o p a g a t i o n d e l a y t i m e Fig.10 Supply Current vs.Supply VoltageS u p p l y c u r r e n t I Ambient temperature T a (˚C )s Preautions for UseGND near the device in order to stabilize power supply line.(2) Handle this product the same as with other integrated circuits against static electricity.(3) As for other general cautions, refer to the chapter “Precautions for Use ”(1) It is recommended that a by-pass capacitor of more than 0.01µF is added between V cc and I F =4mAV CC =V O =15V T a =I CCH I CCLI CCH I CCL I CCH I CCLt ft rV CC =5V I F = 4mA T a =25˚Ct PLHt PHLV CC =5VR L =280ΩT a =25˚CLoad ResistanceLoad resistance R。
