EIOHF以太网远程IO联网产品快速安装指南

EDPF-NT Plus EIO使用手册版本 2.0编号 UG000北京国电智深控制技术有限公司2010年12月版权声明本手册版权归北京国电智深控制技术有限公司所有。

修订历史版本日期说明REV 1.0 2009-1 第1版REV 1.62010-12-22新添网络冗余，虚拟DPU在与EIO网络通讯中断后实现主、备切换，通讯的容错次数为可配置EIO用户使用手册目录1. 简介 (4)2. 设备、任务、虚拟卡件 (4)2.1 定义 (4)2.2 设备与任务的划分规则 (5)2.3 任务与虚拟卡件的对应关系 (5)3. EIO通讯配置步骤 (6)3.1 配置网络环境 (6)3.2 创建虚拟DPU (6)3.3 安装虚拟DPU (7)3.4 组态 (7)3.4.1 创建卡件布置图 (7)3.4.2 配置虚拟卡件 (7)3.5 创建“配置文件” (8)3.5.1 文件目录 (8)3.5.2 配置规则 (8)4. 错误排查与确认 (11)5. 实际工程应用举例 (12)1. 简介EIO即扩展I/O，其支持DCS与第三方系统通讯。

本文档重点介绍DCS通过虚拟DPU与第三方系统通讯的实现方案，虚拟DPU运行在NT+系统的MMI站上，一个虚拟DPU可同时和多个第三方系统通讯。

DCS与第三方系统之间可基于以太网或串口通讯，通讯协议为Modbus over TCP/IP 或Modbus RTU。

在实际应用中，将根据不同需求采用不同的通讯方案：①基于以太网通讯：通讯协议为Modbus over TCP/IP，DCS与每个第三方系统均可视为网络上的一个通讯结点，需要知道每个结点的IP地址和端口号，配置文件中将明确指定每个通讯结点的IP和端口号。

②基于串口通讯：通讯协议为Modbus RTU，DCS与第三方系统之间通过串口服务器作为转接接口。

串口服务器一端通过以太网和DCS连接，另一端则通过RS485和第三方系统连接。

串口服务器通常具有多个连接端口，每个端口连接一个第三方系统。

JetNet 5020G Industrial 16 FE plus 4 GbE/SFP Ethernet SwitchQuick Installation Guide V1.0JetNet 5020G is a high port density Ethernet Switch supports 16 ports Fast Ethernet, and 4 ports Gigabit Ethernet in RJ-45 or SFP for fiber connection. It is designed for field site data convergence to backbone network and up to control data center. The highly heavy industrial Electric-Magnetic Compatibility level, wide operating temperature and voltage provides excellent environmental tolerance to bear the applications which are installed in out -door or the environment with high noise interference, such as factory, railway track-site or Intelligent Traffic Control System (I.T.C.S. ). It also adopts comprehensive network control protocols to enhance network transport performance. with those brilliant system design and network features, the JetNet 5020G will be the best network transmission device for your industrial Ethernet Switch solution.Package Check ListJetNet 5020G DIN Mounting kitDB-9 to RJ-45 Console Cable Quick Installation GuideWiring the Power Inputs & Earth Grounding1. Insert the positive and negative wires into the V+ and V- contact on the terminal block connector.2. Connect the ChassisGrounding to Earth Ground system to obtain electromagnetic immunity to resist lighting, electro static discharge and electric fast transient.3. Tighten the wire-clamp screws to prevent the power wires from being loosened.Notes: The recommended working voltage is DC 24V. Use the UL Listed LPS Power supply with output Rating 10~60V VDC, minimum 2.5A currents.Wiring the Relay OutputThe relay output contacts are in the bottom side. The relay output (DO) is controlled by the pre-defined operating rules. To activate relay output function, please refer to the User’s Manual for more relay output management information.Notes: The relay contact only supports 0.5 A current, DC 24V. It is not recommended to apply voltage and current higher than the specifications.Wiring the Digital InputThe Digital Input (DI) contacts are in the bottom. It accepts one external DC type signal input and can be configured to send alert message through Ethernet when the signal is changed. The signal may trigger and generated by external powerswitch, like as door open trigger switch for control cabinet.Note: the DI accepts DC type signal and supports isolated input circuit with Digital High Level input DC 11V~30V and Digital Low Level input DC 0V~10V. Do not apply voltage higher than the specification; it may cause internal circuit damage or a wrong action of DI.Connecting the Surge/Lighting protectionThe surge protection activate screw located on the bottom side that nearby the power and DI/DO connector. Always tighten the screw and ensure the Chassis-Grounding screw is connected with Earth-Ground well.Note: 1. Ensure the Surge/Lighting is well connecting with Chassis Grounding. 2. Remove the Surge/Lighting Screw before perform insulation/Hi-pot testing.3. Never install or work on/with the equipment or the cabling during the period of its lightning activity.You can configure JetNet 5020G via the RS-232 console with the attached console cable. Or you can remotely manage the switch via network. You can choose Telnet/SSH, Web/HTTPS management.Preparation for console managementAttach the RS-232 DB9 connector to your PC’s COM port. Connect the RJ-45 connector to the console port of the JetNet Switch.1. Go to Start ► Program ► Accessories ► Communication ► Hyper Terminal2. Give a name to the new console connection.3. Choose the COM name and select the correct serial settings. The serial port settings are as below: Baud Rate:115200/Parity: None/Data Bit: 8/Stop Bit: 14. After connected, you will see the Switch login request. Type the username and password and then you can login. The default username is “admin”, password is “admin”.5. Follow the manual to configure the software features.Preparation for Web management1. Launch the web browser on the PC.2. Type http://JetNet Managed Switch_IP_Address (The default IP address is 192.168.10.1.), then press Enter.3. The login screen will appear next. Type in the user name and password and click “OK” button. The default user name and password is admin/admin.4. At the left column of the web management interface are the software features, where ring column will list the available settings.5 Years WarrantyEach of Korenix’s product is designed, produced, and tested with high industrial standard. Korenix warrants that the product(s) shall be free from defects in materials and workmanship for a period of five (5) years from the date of delivery provided that the product was properly installed and used.This warranty is voided if defects, malfunctions or failures of the warranted product are caused by damage resulting from force measure (such as floods, fire, etc.), other external forces such as power disturbances, over spec power input, or incorrect cabling; or the warranted product is misused, abused, or operated, altered and repaired in an unauthorized or improper way.Attention! To avoid system damage caused by sparks, please DO NOT plug in power connector when power is on.The product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronics equipment (RoHS Directives & RoHS 2.0)Korenix Customer ServiceKorenixCARE is Korenix Technology’s global service center, where our professional staffs are ready to answer your questions at any time.EmailaddressofKorenixGlobalServiceCenter:********************SupportInterface IntroductionJetNet 5020G is a DIN Rail Managed Ethernet Switch supports 16 ports Fast Ethernet, and 4 ports Gigabit Ethernet in RJ-45 or SFP for fiber connection.Mounting the unitMount the DIN Rail clip on the rear of JetNet 5020G on the DIN Rail.JetNet 5020G 工业级16百兆, 4千兆管理型以太网络交换机快速安装指南V1.0JetNet 5020G 是一款高密度端口的以太网交换机，支持16端口快速以太网和4个千兆以太网支持RJ-45或SFP 的电口与光口共模设计。

远程 I/O R5 系列通信模块机型: R5－NE1①　①在下列代码中选择。

（例如: R5－NE1/Q）・特殊规格 (例如: /C01)①附加代码◆特殊规格未填写：无特殊规格/Q：特殊规格（请从特殊规格之项另行选择）/C01: 硅涂层/C02: 聚氨酯涂层/C03: 橡胶涂层　IP地址可用组态软件进行设定。

　可在本公司的网站上下载组态软件。

　将本产品连接到电脑时，需要专用的连接电缆线。

所需专　用电缆线的型号请参照本公司网站的下载网站或组态软件　的使用说明书。

　注）此软件的运作状况是在日文版与英文版OS上确认的。

・Ethernet: RJ-45接口・内部通信总线: 连接到底座 (机型: R5－BS) 上・内部电源: 由底座 (机型: R5－BS) 提供隔离: Ethernet－内部通信总线・内部电源间RUN显示灯: 红/绿2色LED通信正常时亮绿色灯；接收数据时亮红色灯(用DIP开关进行切换)ERR显示灯: 红/绿2色LED通信异常时绿色灯亮灯/闪烁；发送数据时，亮红色灯(用DIP开关进行切换)数据占有区设定: 用侧面的DIP开关设定占有区1或占有区2传输类型: 10BASE-T/100BASE-TX传输速度: 10/100Mbps (备有Auto Negotiation功能)通信协议: Modbus/TCP数据: RTU (二进制)通信链接数: 2个通信电缆线:・10BASE-T (STP电缆线Category 5)・100BASE-TX (STP电缆线Category 5e)最长节段: 100mIP地址: 可用组态软件 (机型: R5CON) 进行变更(初始值: 192.168.0.1)端口编号: 502Ethernet显示灯: LINK、DPLX、LINK10、LINK100、COL使用湿度范围: 30～90%RH (无冷凝)使用大气条件: 无腐蚀性气体和严重尘埃安装: 安装在底座 (机型: R5－BS) 上重量: 约100g隔离强度: Ethernet－内部通信总线・内部电源间1500V AC　1分钟电磁兼容指令（EMC指令）　EMI EN 61000-6-4　EMS EN 61000-6-2RoHS指令注) 作为符合EU指令的产品使用时，要与Ver.2.00以上的电源模块 (机型: R5－PS) 一起使用。

PoE•AC一体化路由器电源适配器快速安装指南1.使用电脑连接设备的LAN口，打开浏览器，在地址栏中输入，回车。

2.首次登录时，需设置管理员账号和密码。

2设置路由器如果指示灯显示不正常，请检查连接是否正确。

连接完成后，请检查路由器指示灯是否正常：1连接路由器请按照如下步骤连接路由器：连接网络→连接电源→连接设备→检查指示灯3.登录成功，进入配置向导界面，根据实际需求进行设置。

4.根据设置向导引导，完成配置。

*PoE·AC一体化路由器内置AC（无线控制器）和7口标准PoE供电功能，可统一管理MERCURY AP产品并为其供电，简化家庭无线组网复杂度。

产品尺寸小巧，可部署于家庭信息箱/弱电箱。

附录 常见问题解答无法打开路由器的管理界面（）怎么办？请确保计算机为“自动获得IP地址”。

请确保计算机连接的是路由器的LAN口，并且路由器和计算机网口相应的指示灯已亮起。

请打开IE浏览器，在菜单栏选择“工具”→“Internet选项”，然后单击“连接”按钮，确认选择“从不进行拨号连接”，单击“局域网设置”，确认所有选项均无勾选。

请关闭并重新打开浏览器，或者更换不同的浏览器（如火狐、谷歌浏览器）进行尝试。

请更换网线、或者更换其他的计算机进行尝试。

如果经过上述操作仍无法解决问题，请将路由器恢复出厂设置并重新操作。

请分别从以下方面进行检查：请确保路由器的网线连接已按照步骤“1 连接路由器”连接正确，路由器的LAN、WAN口指示灯状态均正常。

请检查按照本指南中“2 设置路由器”设置的上网方式是否符合您的实际线路环境。

如何判断上网方式可参照下表：路由器设置完成后，无法上网怎么办？宽带拨号上网固定IP地址自动获得IP地址帐号和密码IP地址、子网掩码、网关、DNS服务器运营商没有提供任何参数（不用路由器时计算机不需要进行设置即可直接上网）开通网络时，网络运营商提供的上网参数在通电状态下，按住路由器面板的“Reset”按键直到所有指示灯同时亮起后松开。

P/N: 1802051504013*1802051504013*NPort IA5000A-I/O Series NPort IAW5000A-I/O Series Quick Installation GuideVersion 2.1, January 2021Technical Support Contact Information/support2021 Moxa Inc. All rights reserved.OverviewThe NPort IA5000A-I/O and IAW5000A-I/O Series consist of serial device servers with Digital Input/Output (DIO), providing maximum flexibility to integrate serial equipment in the field into Ethernet networks for a variety of industrial data acquisition applications. The DIO on a device can be controlled over TCP/IP, using the Modbus TCP protocol, and it can be configured and secured from a web browser.Package ChecklistBefore installing the NPort IA5000A-I/O or NPort IAW5000A-I/O Series device server, verify that the package contains the following items: •NPort IA5000A-I/O or NPort IAW5000A-I/O device server with digital I/O•Antenna (for the NPort IAW5000A-I/O Series)•Quick installation guide (printed)•Warranty cardOptional Accessories•Mini DB9F-to-TB Adapter: DB9-female-to-terminal-block adapter for RS-422/485 applications•WK-51-01: Wall-mounting kit•DR-4524: 45W/2A DIN-rail 24 VDC power supply with universal 85 to 264 VAC input•DR-75-24: 75W/3.2A DIN-rail 24 VDC power supply with universal85 to 264 VAC input•DR-120-24: 120W/5A DIN-rail 24 VDC power supply with 88 to 132 VAC or 176 to 264 VAC input, selected by a DIP switchNotify your sales representative if any of the above items are missing or damaged.Hardware IntroductionAs shown in the following figures, the NPort IA5000A-I/O Series has two Ethernet RJ45 LAN ports, and the NPort IAW5000A-I/O Series has one Ethernet RJ45 LAN port and one antenna for WiFi (IEEE 802.11 standards) signal communication, supporting 2.4GHz and 5 GHz frequencies. Both series are equipped with four DIs and two DOs for data acquisition applications. The NPort IA5000A-I/O and IAW5000A-I/O device server series come with built-in 4 kV serial port surge protection.NPort IA5000A-I/O SeriesThe mechanical design of the NPort IA5000A-I/O Series is mostly identical; only the number of serial ports and number of DI/DO channels differ.NPort IAW5000A-I/O SeriesThe mechanical design of the NPort IAW5150A and the NPort IAW5250A is mostly identical; only the number of serial ports and number of DI/DO channels differ.LED IndicatorsName Color FunctionPWR 1, PWR 2 Green Power is being supplied to power input PWR1, PWR2.Ready Red Steady on Power is on, and the NPort isbooting up.Blinking Indicates an IP conflict, or theDHCP or BOOTP server did notrespond properly, or a relayoutput occurred.When the above two conditionsoccur at the same time.Check the relay output first. If theReady LED is still blinking afterresolving the relay output, thenthere is an IP conflict, or the DHCPor BOOTP server did not respondproperly.FlashingquicklymicroSD card failedGreen Steady on Power is on, and the NPort isfunctioning normally.Blinking The device server has beenlocated by Administrator’sLocation functionOff Power is off, or a power error condition exists.WLAN (Only for the NPortIAW5000A-I/O) Green Steady on Wireless is enabledBlinking NPort can’t establish WLANconnection with AP(Infrastructure) or station(Ad-Hoc)Off Wireless is not enabled.Signal Strength (3 LEDs only for the NPortIAW5000A-I/O) Green 1 Bottom The signal strength (RSSI) is lessthan -74 dBm2 Middle The signal strength (RSSI) isbetween -65 to -74 dBm3 Top The signal strength (RSSI) isgreater than -65 dBmEthernet Amber 10 Mbps Ethernet connectionGreen 100 Mbps Ethernet connectionOff The Ethernet cable is disconnected or has ashort.P1, P2 (Serial) Amber Serial port is receiving data.Green Serial port is transmitting dataOff No data is being transmitted or receivedthrough the serial port.DI Green DI status onOff DI status offDO Green DO status onOff DO status offHardware Installation ProcedureSTEP 1: After unpacking the unit, connect the power supply to the unit. STEP 2: Use an Ethernet cable to connect the unit to the network. STEP 3: Connect your device to the desired port on the unit.STEP 4: Place or mount the unit. The unit may be placed on ahorizontal surface such as a desktop, or mounted on the wall. Mounting OptionsThe NPort IA5000A-I/O and IAW5000A-I/O are designed to be attached to a DIN rail or mounted on a wall.STEP 1: Insert the top of the DIN rail into the slot. STEP 2: The DIN rail attachment unit will snap into place as shown at right.Wall Mounting (optional)For some applications, it may be more convenient to mount the NPort IA5000A-I/O or IAW5000A-I/O to a wall, as illustrated below.Do not drive the screws in all the way—leave a space of about 2 mm to allow room for sliding the wall-mounting panel between the wall and the screws.NOTE Test the screw head and shank size by inserting the screws into one of the keyhole-shaped apertures of the wall-mounting platesbefore they are fixed to the wall.STEP 3: Once the screws are fixedinto the wall, insert the four screwheads through the large openingof the keyhole-shaped apertures,and then slide the NPortdownwards, as indicated to theright. Tighten the screws for addedstability.Termination Resistor and Adjustable Pull-Up/Down ResistorsIn some critical environments, you may need to add termination resistors to prevent the reflection of serial signals. When using termination resistors, it is important to set the pull-up/down resistors correctly so that the electrical signal is not corrupted. The NPort IA5000A-I/O andIAW5000A-I/O Series use DIP switches to set the pull-up/down resistor values for each serial port. The DIP switches are located at the side of wireless device server for easy setting.To add a 120 Ω termination resistor, set switch 3 on the port’s assigned DIP switch to ON; set switch 3 to OFF (the default setting) to disable the termination resistor.To set the pull-up/down resistors to 150 KΩ, set switches 1 and 2 on the port’s assigned DIP switch to OFF. This is the default setting.To set the pull-up/down resistors to 1 KΩ, set switches 1 and 2 on the port’s assigned DIP switch to ON.Pull-Up/Down Resistors for the RS-485 PortSW1 (Serial 1) SW2 (Serial 2)DIP 1Pull-up resistorDIP 2Pull-down resistorDIP 3Terminal resistorON 1 KΩ 1 KΩ120 ΩOFF (Default) 150 KΩ150 KΩN/A NOTE Do not use the 1 KΩ setting while in RS-232 mode. Doing so will degrade the RS-232 signals and reduce the effectivecommunication distance.Software Installation InformationFor software installation, download the relative utilities from Moxa’s website:https:///support/support_home.aspx?isSearchShow=1•Download the NPort Windows Driver Manager and install it as the driver to run with Real COM mode of the NPort Series.•Execute NPort Windows Driver Manager; then map the virtual COM ports on your Windows platform.•You may refer to the DB9 Male pin assignment section to loop back pin 2 and pin 3 for the RS-232 interface to carry out a self-test on the device.•Use HyperTerminal or a similar program (you may download Moxa’s program, called PComm Lite) to test whether the device is good or not.Setting the IP AddressThe factory default IP settings are assigned as follows:NPort IA5000A-I/O SeriesLAN IP NetmaskStatic 192.168.127.254 255.255.255.0NPort IAW5000A-I/O SeriesLAN IP NetmaskStatic 192.168.126.254 255.255.255.0WLAN IP NetmaskStatic 192.168.127.254 255.255.255.0If the NPort is configured for DHCP but the DHCP server cannot be found, the NPort will use factory default IP settings.NOTE If you have forgotten the NPort’s IP address, use the Device Search Utility from your PC to locate the NPort. After searchingthe LAN for NPort units, the Device Search Utility will display theIP address of each unit.NOTE (For the NPort IAW5000A-I/O Series)Ethernet Bridge Disabled (default): Only one networkinterface can be active at a time. If the Ethernet link is active, theWLAN will be inactive. If the WLAN is active, the Ethernet link willbe inactive.Ethernet Bridge Enabled: The LAN and WAN will both beactive. Go to the web console, find the network settings page,and set Ethernet Bridge to Enabled.Open the web console to make the configuration changes as follows: STEP 1: Open your web browser.STEP 2: In the address bar, enter the default IP address (for the NPort IA5000A-I/O Series, it is 192.168.127.254; for the NPort IAW5000A-I/O Series, it is 192.168.126.254)STEP 3: The web server will ask for the username and password before you log in. To configure the device server, you may use the default user/default password admin /moxa to log in the web console.STEP 4: For first-time use, click the Wizard in the left navigation panel. The wizard will prompt you to configure the IP address and basic settings. For other settings, use the factory defaults or modify the settings for your application.Pin AssignmentsRJ45 (LAN) PinLAN 1Tx+ 2Tx- 3Rx+ 4– 5– 6Rx- 7– 8 –DB9 Male (RS-232/422/485) PinRS-232 RS-422/RS-485-4W RS-485-2W 1DCD TxD-(A) – 2RxD TxD+(B) –3 TxD RxD+(B) Data+(B) 4DTR RxD-(A) Data-(A) 5GND GND GND 6DSR – – 7RTS – – 8CTS – – 9 – – –Power Input and Relay Output PinoutsV2+ V2- V1+ V1- DC Power Input 2 DC Power Input 2 N.O. Common N.C. DC Power Input 1 DC Power Input 1DI/DO PinoutsDO0 DO1 GND DI0 DI1 DI2 DI3 COM GND Digital Output 0 Digital Output 1 Ground Digital Input 0 Digital Input 1 Digital Input 2 DigitalInput 3 Common GroundSpecificationsPower Input12 to 48 VDC Power Consumption NPort IA5000A-I/O: 300 mA @ 12 VNPort IAW5000A-I/O: 300 mA @ 12 VOperating Temperature Standard models:0 to 60°C (32 to 140°F)Storage Temperature-40 to 85°C (-40 to 185°F)Operating Humidity 5 to 95% RHDimensions (W x D x H) NPort IA5000A-I/O:59.6 x 101.4 x 134 mm (2.35 x 4.0 x 5.28 in)IAW5000A-I/O:59.6 x 101.4 x 134 mm (2.35 x 4.0 x 5.28 in)Magnetic Isolation 1.5 kV for EthernetRegulatory Approvals EMCCE: EN 61000-6-2/6-4FCC: FCC Part 17 Subpart B, Class AFCC Part 15 Subpart B, Class ASafetyUL: UL 60950-1LVD: EN 60950-1DSPR: ARIB-STD 33, ARIB-STD 66Fault Relay Circuit 3-pin circuit with current-carrying capacity of2 A @ 30 VDCATTENTIONThis equipment is intended to be used in Restricted AccessLocation.WARNING:HOT SURFACE. DO NOT TOUCH! Before touching the surface, pay special attention and take the necessary protection measures.。

目录1 概述..................................................... 错误!未定义书签。

网动公司简介..................................... 错误!未定义书签。

Active Meeting 简介.............................. 错误!未定义书签。

Active Meeting (会议室版)特点.................... 错误!未定义书签。

2 手册阅读方法............................................. 错误!未定义书签。

标记方式......................................... 错误!未定义书签。

文本标记..................................... 错误!未定义书签。

图标......................................... 错误!未定义书签。

3 基本概念阐述............................................. 错误!未定义书签。

4 详细功能阐述............................................. 错误!未定义书签。

服务器端功能介绍................................. 错误!未定义书签。

服务器程序功能............................... 错误!未定义书签。

系统管理员后台功能介绍....................... 错误!未定义书签。

公司管理员后台功能介绍....................... 错误!未定义书签。

主持人后台功能介绍........................... 错误!未定义书签。

ioLogik E2200SeriesSmart Ethernet remote I/O with Click&Go LogicFeatures and Benefits•Front-end intelligence with Click&Go control logic,up to24rules•Active communication with MX-AOPC UA Server•Saves time and wiring costs with peer-to-peer communications•Supports SNMP v1/v2c/v3•Friendly configuration via web browser•Simplifies I/O management with MXIO library for Windows or Linux•Wide operating temperature models available for-40to75°C(-40to167°F)environmentsCertificationsIntroductionMoxa’s ioLogik E2200Series Ethernet Remote I/O is a PC-based data acquisition and control device that uses proactive,event-based reporting to control I/O devices and features the Click&Go programming interface.Unlike traditional PLCs,which are passive and must poll for data,Moxa’s ioLogik E2200Series will,when paired with our MX-AOPC UA Server,communicate with SCADA systems using active messaging that is pushed to the server only when state changes or configured events occur.Additionally,the ioLogik E2200features SNMP for communications and control using an NMS(Network Management System),allowing IT professionals to configure the device to push I/O status reports according to configured specifications.This report-by-exception approach,which is new to PC-based monitoring,requires far less bandwidth than traditional polling methods.PC-Free Alarm and Control IntelligenceThis device supports simple yet powerful Click&Go™technology toconfigure event-driven reports and alarms delivered over email,TCP/UDP,or SNMP traps,giving you a powerful and effective tool fordelivering timestamped status updates in real time.With built-in Click&Go™intelligence,this device can be configuredfor simple outputs paired up with simple input triggers without theneed for a PC controller.This allows it to be configured toautomatically report I/O events according to conditions specified bythe user.SNMP for Ethernet Device ManagementBy using SNMP,IT engineers can configure the device to deliver alarms(traps)for specific I/O events,or use it to read or write directly to the I/O registers.For the strongest security,the device features SNMPv3,with authentication and encryption.With Moxa’s SNMP-capable I/O,even IT professionals can easily integrate industrial sensors and servos over an Ethernet backbone,and with its strong network management tools,it is ideal for a wide variety of industrial applications,including environmental monitoring,telecommunications,power production and delivery,and transportation.Push Technology for Events and AlarmsWhen used with MX-AOPC UA Server,devices can use active pushcommunications when communicating changes in state and/orevents to a SCADA system.Unlike a polling system,when using apush architecture for communications with a SCADA system,messages will only be delivered when changes in state or configuredevents occur,resulting in higher accuracy and lower amounts of datathat need to be transferred.SpecificationsControl LogicLanguage Click&GoInput/Output InterfaceDigital Input Channels ioLogik E2210Series:12ioLogik E2212Series:8ioLogik E2214Series:6Digital Output Channels ioLogik E2210/E2212Series:8ioLogik E2260/E2262Series:4Configurable DIO Channels(by software)ioLogik E2212Series:4ioLogik E2242Series:12Relay Channels ioLogik E2214Series:6Analog Input Channels ioLogik E2240Series:8ioLogik E2242Series:4Analog Output Channels ioLogik E2240Series:2RTD Channels ioLogik E2260Series:6Thermocouple Channels ioLogik E2262Series:8Buttons Reset buttonRotary Switch0to9Isolation3k VDC or2k VrmsDigital InputsConnector Screw-fastened Euroblock terminalSensor Type ioLogik E2210Series:Dry Contact and Wet Contact(NPN)ioLogik E2212/E2214/E2242Series:Dry Contact and Wet Contact(NPN or PNP) I/O Mode DI or event counterDry Contact On:short to GNDOff:openWet Contact(DI to GND)On:0to3VDCOff:10to30VDCCounter Frequency900HzDigital Filtering Time Interval Software configurablePoints per COM ioLogik E2210Series:12channelsioLogik E2212/E2242Series:6channelsioLogik E2214Series:3channelsDigital OutputsConnector Screw-fastened Euroblock terminalI/O Type SinkI/O Mode DO or pulse outputCurrent Rating200mA per channelPulse Output Frequency1kHzDIO Output Leakage Current 4.0mA@24VDCOver-Current Protection0.65A per channel@25°COver-Temperature Shutdown175°C(min.)Over-Voltage Protection45VDC(typical)RelaysConnector Screw-fastened Euroblock terminalType Form A(N.O.)power relayI/O Mode Relay or pulse outputPulse Output Frequency0.3Hz at rated loadContact Current Rating Inductive load:2A@30VDC,250VAC,110VACResistive load:5A@30VDC,250VAC,110VACMinimum Permitted Load1A@5VDCContact Resistance100milli-ohms(max.)Electrical Endurance100,000operations@5A resistive loadMechanical Endurance1,000,000operationsNote Ambient humidity must be non-condensing and remain between5and95%.The relaysmay malfunction when operating in high condensation environments below0°C. Analog InputsConnector Screw-fastened Euroblock terminalI/O Mode Voltage/CurrentI/O Type DifferentialResolution16bitsInput Range ioLogik E2240Series:±150mV,±500mV,±5V,±10V,0to20mA,4to20mAioLogik E2242Series:±150mV,0to150mV,±500mV,0to500mV,±5V,0to5V,±10V,0to10V,0to20mA,4to20mAAccuracy ioLogik E2240/E2242:±0.1%FSR@25°C±0.3%FSR@-10to60°CioLogik E2240-T/E2242-T:±0.1%FSR@25°C±0.3%FSR@-10to60°C±0.5%FSR@-40to75°CSampling Rate ioLogik E2240Series:All Channels:10samples/sec for voltage;6samples/sec for currentPer Channel:1.25samples/sec for voltage;0.75samples/sec for currentSingle channel:1.25samples/sec for voltage;0.75samples/sec for currentioLogik E2242Series:All channels:32samples/secPer channel:8samples/secSingle channel:100samples/secBuilt-in Resistor for Current Input120ohmsInput Impedance ioLogik E2240Series:900kilo-ohms(min.)ioLogik E2242Series:200kilo-ohms(min.)Over-Voltage Protection-25to+30VDC(power on)-35to+35VDC(power off)Analog OutputsConnector Screw-fastened Euroblock terminalI/O Mode Voltage/CurrentOutput Range0to10VDC4to20mAResolution12-bitAccuracy ioLogik E2240:±0.1%FSR@25°C±0.3%FSR@-10to60°CioLogik E2240-T:±0.1%FSR@25°C±0.3%FSR@-10to60°C±0.5%FSR@-40to75°CLoad(Current Mode)Internal power:250ohms(max.)RTDsConnector Screw-fastened Euroblock terminalSensor Type JPT100,JPT200,JPT500(-200to640°C)JPT1000(-200to350°C)NI100,NI200,NI500(-60to250°C)NI1000(-60to150°C)NI120(-80to260°C)PT1000(-200to350°C)PT50,PT100,PT200,PT500(-200to850°C)Resistance of310,620,1250,and2200ohmsInput Connection2-or3-wireSampling Rate All channels:12samples/secPer channel:2samples/secResolution0.1°C or0.1ohmsAccuracy ioLogik E2260:±0.1%FSR@25°C±0.3%FSR@-10to60°CioLogik E2260-T:±0.1%FSR@25°C±0.3%FSR@-10to60°C±0.5%FSR@-40to75°CInput Impedance625kilo-ohms(min.)ThermocouplesConnector Screw-fastened Euroblock terminalSensor Type J,K,T,E,R,S,B,NMillivolt Type±19.532mV±39.062mV±78.126mVFault and over-voltage protection:-35to+35VDC(power off);-25to+30VDC(poweron)Resolution16bitsMillivolt Accuracy ioLogik E2262:±0.1%FSR@25°C±0.3%FSR@-10to60°CioLogik E2262-T:±0.1%FSR@25°C±0.3%FSR@-10to60°C±0.5%FSR@-40to75°CTC Accuracy Types J,T,E,S,B:±5°CTypes K,R,N:±8°CCJC Accuracy±0.5°C@25°C±1.5°C@-40to75°CSampling Rate All channels:12samples/secPer channel:1.5samples/secInput Impedance1mega-ohms(min.)LED InterfaceLED Indicators PWR,RDY,Serial,I/O StatusEthernet Interface10/100BaseT(X)Ports(RJ45connector)1Magnetic Isolation Protection 1.5kV(built-in)Ethernet Software FeaturesConfiguration Options Windows Utility(ioAdmin),Web Console(HTTP)Industrial Protocols Modbus TCP Server(Slave),SNMPv1/v2c/v3,SNMPv1Trap,Moxa AOPC(Active Tag),MXIO Library,CGI commandsManagement BOOTP,IPv4,SMTP,DHCP Client,HTTP,TCP/IPMIB Device Settings MIBTime Management SNTPSecurity FunctionsAuthentication Local databaseEncryption HMACSecurity Protocols SNMPv3Modbus TCPFunctions Supported1,2,3,4,5,6,15,16Mode Server(Slave)Serial InterfaceConnector Terminal blockSerial Standards RS-485No.of Ports1Baudrate1200,2400,4800,9600,19200,38400,57600,115200bps Parity NoneData Bits8Stop Bits1Flow Control NoneSerial SignalsRS-485-2w Data+,Data-,GNDSerial Software FeaturesIndustrial Protocols Modbus RTU MasterPlatformReal-time Clock(RTC)Real-time clock with battery backupPower ParametersPower Connector Screw-fastened Euroblock terminalNo.of Power Inputs1Input Voltage12to36VDCPower Consumption ioLogik E2210Series:202mA@24VDCioLogik E2212Series:136mA@24VDCioLogik E2214Series:170mA@24VDCioLogik E2240Series:198mA@24VDCioLogik E2242Series:178mA@24VDCioLogik E2260Series:95mA@24VDCioLogik E2262Series:160mA@24VDCPhysical CharacteristicsDimensions115x79x45.6mm(4.53x3.11x1.80in)Weight250g(0.55lb)Installation DIN-rail mounting,Wall mountingWiring I/O cable,16to26AWGPower cable,16to26AWGHousing PlasticEnvironmental LimitsOperating Temperature Standard Models:-10to60°C(14to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Altitude2000m1Standards and CertificationsSafety UL508EMC EN61000-6-2/-6-4EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:4kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:10V/mIEC61000-4-4EFT:Power:2kV;Signal:1kVIEC61000-4-5Surge:Power:1kVIEC61000-4-6CS:10VIEC61000-4-8PFMFShock IEC60068-2-27Vibration IEC60068-2-6Freefall IEC60068-2-32DeclarationGreen Product RoHS,CRoHS,WEEEMTBFTime ioLogik E2210Series:213,673hrsioLogik E2212Series:217,722hrsioLogik E2214Series:307,329hrsioLogik E2240Series:155,941hrsioLogik E2242Series:204,391hrsioLogik E2260Series:327,282hrsioLogik E2262Series:341,063hrsStandards Telcordia SR332WarrantyWarranty Period ioLogik E2214Series:2years2ioLogik E2210/E2212/E2240/E2242/E2260/E2262Series:5years Details See /warrantyPackage ContentsDevice1x ioLogik E2200Series remote I/ODocumentation1x quick installation guide1x warranty card1.Please contact Moxa if you require products guaranteed to function properly at higher altitudes.2.Because of the limited lifetime of power relays,products that use this component are covered by a2-year warranty.DimensionsOrdering InformationModel Name Input/Output Interface Digital Input Sensor Type Analog Input Range Operating Temp.ioLogik E221012x DI,8x DO Wet Contact(NPN),DryContact–-10to60°CioLogik E2210-T12x DI,8x DO Wet Contact(NPN),DryContact–-40to75°CioLogik E22128x DI,4x DIO,8x DO Wet Contact(NPN or PNP),Dry Contact–-10to60°CioLogik E2212-T8x DI,4x DIO,8x DO Wet Contact(NPN or PNP),Dry Contact–-40to75°CioLogik E22146x DI,6x Relay Wet Contact(NPN or PNP),Dry Contact–-10to60°CioLogik E2214-T6x DI,6x Relay Wet Contact(NPN or PNP),Dry Contact–-40to75°CioLogik E22408x AI,2x AO–±150mV,±500mV,±5V,±10V,0-20mA,4-20mA-10to60°CioLogik E2240-T8x AI,2x AO–±150mV,±500mV,±5V,±10V,0-20mA,4-20mA-40to75°CioLogik E224212x DIO,4x AI Wet Contact(NPN or PNP),Dry Contact±150mV,0-150mV,±500mV,0-500mV,±5V,0-5V,±10V,0-10V,0-20mA,4-20mA-10to60°CioLogik E2242-T12x DIO,4x AI Wet Contact(NPN or PNP),Dry Contact±150mV,0-150mV,±500mV,0-500mV,±5V,0-5V,±10V,0-10V,0-20mA,4-20mA-40to75°CioLogik E22604x DO,6x RTD––-10to60°C ioLogik E2260-T4x DO,6x RTD––-40to75°C ioLogik E22624x DO,8x TC––-10to60°C ioLogik E2262-T4x DO,8x TC––-40to75°C Accessories(sold separately)SoftwareMX-AOPC UA Server OPC UA Server software for converting fieldbus to the OPC UA standard©Moxa Inc.All rights reserved.Updated May05,2022.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。

EIO远程IO联网设备说明书(Ver2.6)一、产品说明 (3)1．EIO介绍 (3)2．的优势及应用范围 (4)二、使用及配置 (5)1、快速安装 (5)1.最小系统需求 (5)2.安装 (5)3.检查EIO运行状态 (6)4.安装使用虚拟串口软件 (7)5.恢复出厂值 (10)6.设备配置 (10)2、网络参数设置 (11)3、配置EIO (11)4、EIO控制协议 (12)5、注意事项 (12)6、免责声明 (12)三、常见问题 (13)四、保修服务及技术支持。

(13)1、免费保修 (13)2、免费保修服务方式 (13)3、不属于免费保修的情况 (14)23一、一、 产品说明产品说明1． EIO 介绍介绍EIO 是同时集成I/O 控制和RS232/RS485串口服务器的以太网设备，同时具备开关量输出、开关量采集、串口服务器等功能，可同时替代I/O 卡和串口服务器。

支持Socket、虚拟串口两种用户通讯接口，用户可以按照Socket 标准，通过TCP/IP 连接与EIO 进行通讯。

也可以通过VSPM 虚拟串口软件，将EIO 虚拟成普通串口设备，可以有效的降低软件编写难度。

EIO 采用国际通用的Modbus TCP 作为通讯协议，可以与各类组态软件无缝结合。

首创EIO Link 技术，互联2个EIO 设备，可以将远程的开关量状态传输到控制中心，并完整重现，控制中心的开关量状态也可以传输到现场，2个EIO 的串口也可以进行透明数据传输，整个控制过程无需电脑，完全由2个EIO 实现。

EIO 设备具备光电隔离、ESD 防护等多用防护措施，可以稳定的工作在恶劣环境中。

2．的优势及应用范围的优势及应用范围优势优势比传统的电脑+I/O控制卡结构功能更多，工作更稳定。

同时集成I/O控制和协议转发，性价比更高。

实用化设计，简化部署难度。

较高的附加值。

提供例子程序的源代码，以及各种开发支持。

应用范围应用范围基于Internet的智能家居，安防系统设计。

ioLogik E2200系列具備Click&GO邏輯的智慧乙太網路遠端I/O特色與優點•具備專利Click&Go控制邏輯的前端智慧，多達24項規則•與MX-AOPC UA伺服器進行的主動通訊•透過點對點通訊節省時間和接線成本•支援SNMP v1/v2c/v3•透過網頁瀏覽器輕鬆完成配置•使用Windows或Linux版MXIO程式庫簡化I/O管理•支援寬溫工作環境，適合-40至75°C（-40至167°F）環境認證簡介Moxa的ioLogik E2200系列乙太網路遠端I/O是PC型資料擷取和控制裝置，使用基於事件的主動報告來控制I/O裝置，並採用Click&Go程控介面。

不同於被動而且必須輪詢資料的傳統PLC，Moxa的ioLogik E2200系列與我們的MX-AOPC UA伺服器配對時，將使用主動訊息與SCADA系統進行通訊，該訊息僅在發生狀態變更或配置事件時推送到伺服器。

此外，ioLogik E2200配備使用NMS（網路管理系統）進行通訊和控制的SNMP，IT專業人員可以將裝置配置為按照已配置的規格推送I/O狀態報告。

這種在例外狀況發生時進行報告的方法是基於PC的監控的新方法，相較於傳統輪詢方法，這需要的頻寬更少。

免PC告警和控制智慧這個裝置支援簡單而強大的Click&Go™技術，可配置透過電子郵件、TCP/UDP或SNMP陷阱傳送的事件驅動報告和告警，為您提供強大而有效的工具，以即時傳送有時間戳記的狀態更新。

藉由內建的Click&Go™智慧，可以對於與簡單輸入觸發條件配對的簡單輸出配置這個裝置，而不需要PC控制器。

這個裝置由於這項特點而能夠按照使用者指定的條件自動報告I/O事件。

用於乙太網路裝置管理的SNMP藉由使用SNMP，IT工程師可以將裝置配置為針對特定I/O事件傳送告警(SNMP trap)，或用來直接讀取或寫入I/O暫存器。