霍尼韦尔安全开关(新编版)

1、容错以太网是PKS的控制网络，FTE不但提供了容错的特点，也提供了快速网络的相应，及工业以太网的控制应用的安全性。

FTE（Fault Tolerant Etherent）容错以太网，是冗余网络结构的单网，通过Honeywell的FTE驱动，及商用的网络设备实现的。

FTE网络包括冗余的交换机和电缆。

拓扑：双重并行树形网络在顶部接在一起。

2、交换机之间的级联线（cross link）构成单网。

商用的网络设备指交换机、双口单网卡或单口双网卡。

FTE网络通讯检测画面检测画面启动3、系统必须有控制器、服务器、操作站组成。

4、FTE网络包括冗余交换机和电缆。

树网：连接到A交换机上A口形成的网叫A网（Yellow tree）。

连接到B交换机上B口形成的网叫B网（Green tree）。

Localhost 接收数据节点。

FLEX操作站（F站）：过程数据及相关的报警和事件，还有其他数据信息，直接来自服务器；组态ES-F两种连接方法：固定连接方法（Static）：提供了特定ES-F的一种永久性专用连接。

轮替连接方法（Rotary）：提供了一种按需的连接，适用不需要全日制操作访问时。

Console操作站（C站）：过程数据及相关的报警和事件，直接来自于控制器；其他数据信息来自于服务器；Console Extension操作站（CE）：过程数据及相关的报警和事件，还有其他数据信息，全部信息都来自与C站。

7、一个C300控制器带有两个IOLINK，每个IOLINK最多支持40个IO卡件，而一个控制器最多支持64个IO卡件。

每套C300控制器最多支持64个IO Units（IOU）。

C300控制器必须与控制防火墙连接。

C300控制器主控制器FTE地址设定奇数，备用控制器地址为主控制器的地址+1。

Control Firewall（CF9）控制防火墙：在FTE网络中是成对出现的，8+1口，其中有一个专门的网线路口用于向上连接交换机，其余的8个网口可以连接控制器。

微动开关Honeywell目录号说明电气数据和UL代码O.F.Noz最小R.F.Noz最大RT.mmin最小O.T.mminD.T.mmin最大O.P.*mmin 3MN1 用于大多数应用场合15 AV3,34-5,5612.201,6761,52.0602,03.0800,38-0,63.015-.0252,16.085 3MN6 力较小场合 15AV1,95-3,17-111,1141,52.0602,03.0800,38-0,63.015-.0252,16.085Honeywell/Commercial Switch-Sensor 霍尼韦尔开关与传感器1上海: Tel:021-******** 北京: Tel:010-******** 深圳: Tel:0755-******* 广州: Tel:020-******** e-mail:jian.bo.zhou@/ /sensing双断3MN系列特点.080英寸的最小超行程有高达15 A的功率负荷开关容量有240 vac时1马力的电动机处理能力机械寿命长达10,000,000次循环-95%完好率用抗弧塑料端子与端子间间距更大，能有效地降低短路的可能性用8号接线螺钉UL，CSA认证一般信息3MN开关可与限位或控制机构一起用在机床、压力机或其它工业设备上。

这些开关在安装时容易连接。

双断开关端子的接线必须在同一电压源和同一极上。

其负荷应在线路的同侧。

电气额定值电路电气数据和UL标准双电路双断V 电动机控制15A，120，240，480或600 vac;1/2HP，120 vac; 1hp，240 vac;0.8A，115 vdc;0.4A，230 vdc。

特性:O.F.-动作力; R.F.-释放力; P.T.-预行程;订货指南O.T.-超行程; D.T.-差动行程; O.P.-操作位置外形图，图1*±0.38 mm±.015 in安装尺寸(仅供参考)0,0=mm图例:0.00=in直径的安装孔(2)图1。

Honeywell PKS系统维护手册第一章日常维护第二章卡件更换第三章控制器第四章I/O卡件第五章常见故障第六章PID整定系统使用维护DCS系统是由系统软、硬件，操作台盘及现场仪表组成的。

系统中任一环节出现问题，均会导致系统部分功能失效或引发控制系统故障，严重时会导致生产停车。

因此，要把构成控制系统的所有设备看成一个整体，进行全面维护管理。

1.1日常维护1.1.1机柜室管理应加强机柜室人员和设备管理。

为保证系统运行在适当条件下，请遵守以下各项：1）密封所有可能引入灰尘、潮气和鼠害或其它有害昆虫的走线孔（坑）等；2）保证空调设备稳定运行，保证室温变化小于+5℃/h，避免由于温度、湿度急剧变化导致在系统设备上的凝露；3）现场与控制室合理隔离，避免现场灰尘进入控制室，同时控制室定时清扫，保持清洁。

4）进入机房、工程师室作业人员严格遵守各项规章制度，进出须换鞋或带鞋套，不得将污物、食品、饮料等带入机房；爱护机房、工程师室内设备，保持机房、工程师室整洁；进入机柜间应关闭手机。

5）过程控制计算机机柜间内禁止使用无线对讲设备。

6）技术组全面负责过程控制计算机的管理，各班组负责过程控制计算机机房、工程师室的日常卫生和日常维护工作。

工程师室内计算机及网络设备的维修由技术组成员负责，班组配合。

技术组成员在维修完设备后应做好设备规格化工作。

7）日光灯完好、灭火器按期检查、室内卫生整洁、操作台（柜）、主机外部、显示器、打印机等卫生清洁、打印机不缺纸、机柜内设备如机柜过滤网清洁、风扇完好，电话机、其他未明确但属于共有的设备等完好。

8）布线层的槽盒盖可以不盖，但应根据规格大小整洁地放置在地面上。

布线层墙壁、电缆进线口应密封，无人时，电灯只保留一组常亮。

9）室内施工管理：本班的设备施工作业由本班完成，外委作业时由本班派人监护（包括分析、检修等工作涉及更改电源时）。

施工结束后应做到工完料净场地清，负有管理责任的班组应及时向对方班组指出施工作业后的室内卫生等问题。

装好保护键的开关WW 可供带有或不带柱塞保护装置的可提供一保护键它与柱塞保护装置一起使用使开关的柱塞保持在压下状态(见右面的照片→)安装尺寸(仅供参考)总体介绍WW 系列开关机构是一种非快速的双断短杆型结构可供单路两路或三路的多种型号产品三路开关有两个极所谓 “极”是指能在同一时间通过拨动开关的完全独立的电路的数目在一个三路开关中在非操作运行条件下(见图)电路#2是闭合的而电路#1和#3是断开的当被压下时电路#2断开而电路#1和#3闭合因为开关接通/断开两个单独的电路(#1和#3)所以称这个开关是两极的当柱塞被松开时电路#1和#3断开而电路#2闭合柱塞保护装置变型产品和保护键特 点 • 面板快速安装 • 各种端子尺寸• 可容纳快速连接绝缘端子 •在125或250VAC 时按电路数和端接数的不同电气额定值为10-16A•双极DM 开关有相同的面板开 孔• 快速连接D7D9端接装置符合VDE 关于3mm 空隙的要求 • 配有柱塞保护装置和D7D9端接装置的开关经VDE 批准认可 • ULCSA 认证• 操作员可接近的联锁开关符合UL100,000次动作的要求 • 受控于UL 标准508 “工业电机控制装置”用于 厚 用于 厚 最大面板孔详图最大快速连接 端接片参考(2) 最大参考(2)参考 参考最大超行程位置操作位置 参考自由位置注: 端子可容纳AMP Hollingsworth 或其它厂商供货的快速连接插座电气额定值UL和CSA*在带有*的负载下经100,000次循环试验电气额定值3极电气额定值2极电气额定值1极C 触点1-1,3-3:g*15A,125 V AC,*10A,250 V AC:1/2马力@125,250 V AC;3A “L”125 V AC150V A试验负载@125/250V AC A 触点1-1,3-3:g*16A,125/250 V AC1/2马力,125/250 V AC:3A “L”125 V AC150 V A试验负载125/250 V AC;*2A24VDCB 触点1-1:*16A,125/250 V AC3/4马力125/250 V AC150V A试验负载125/250 V AC3A,“L”,125V ACD 0,1A,125V AC与C相同*2A,24VDCF 0.1A125V AC与A相同E 1触点2-2:0.1A125V AC/VDCG *5A,125V AC 2A*24 VDCVDE✝在带有标记的负载下经10,000次循环试验电路1#和#3✝16(4)A250 V AC电路#2✝0.1(0.05)A250 V AC订货指南电路系统电气额定值柱塞保护装置WW1A04A-D7 #1-常开 A无WW1G03A-D7 #1和#3 – 常开 A 无WW1K06D-D7 #1和#3 – 常开#2-常闭CE无WW1G02A-D9 #1和#3 – 常开 A 有WW1K05D-D9 #1和#3 – 常开#2-常闭CE有保护键: 目录号15PA256-WW端接装置选项目录号代码订购其它端接装置选项时在目录号的末尾代以选项型式字母和数字号动作D7:187×.032in(4,75×0,8mm)D8:187×.020in(4,75×0,5mm)电路系统D9:250×.032in(6,35×0,8mm) 变型电气额定值端接装置D7和D9端子是经VDE认证的VDE限制D7端子于12A。

霍尼韦尔净化器安全操作及保养规程随着现代生活水平的不断提高，人们对生活环境的要求也越来越高。

在生活中，空气净化器被越来越多的人所使用。

霍尼韦尔净化器是一款高端的净化器，具有较高的净化效果和易于操作的特点。

下面，本文将介绍霍尼韦尔净化器的安全操作及保养规程，以帮助用户正确认识和使用净化器。

一、安全操作规程1.1 电源插头在插拔电源插头时应该始终保持手干燥，确定插头已连接到插座上，并确认插座电压与净化器电压相同。

同时，按下插头或插座上的开/关开关，并确保净化器已打开。

1.2 防火安全使用净化器时，不要在净化器附近放置易燃材料，并确保周围有足够空间进行通风。

除了推荐的滤芯和配件外，不要使用其他零部件。

1.3 禁止拆卸在使用净化器时，不要对净化器进行任何拆卸或维修操作。

不用时，将净化器从插座上拔下，并将其放在干燥，安全的地方。

1.4 离开房间如果需要暂时离开房间，建议将净化器关闭并拔掉电源插头。

如果长时间不使用净化器，建议将其开关置于“关闭”位置。

1.5 儿童和宠物将净化器放置在儿童和宠物无法触及的位置，并确保儿童和宠物无法拆卸净化器装置和零部件。

二、保养规程2.1 滤芯更换滤芯是净化器保持好效果的核心。

在使用中，应定期更换滤芯。

在贴有指示标签的滤芯上，记录滤芯使用时间和更换日期。

更换的周期大约为8-12个月。

在使用过程中，若出现滤芯破损、变形等情况，应及时更换。

2.2 机体清洁净化器外表面有灰尘，应使用干净、软布擦拭清洁，避免使用含清洁剂或酒精的清洁液。

同时，应严禁将薄膜覆盖在机体的表面。

2.3 机体检查不定期检查机体及插头是否有明显的损坏或磨损，确保净化器正常运行。

2.4 运输在搬运净化器时，应注意避免机体受到硬物或重压的冲击。

在安装时，避免在净化器身上施加过多的压力，以免机体和配件受到损坏。

三、总结霍尼韦尔净化器是一种高科技、高性能的净化器，具有卓越的净化效果和易于操作的特点。

然而，如果用户不能正确运用和维护它，则效果和使用寿命将大大降低。

霍尼韦尔安全开关(通用版)
Security technology is an industry that uses security technology to provide security services to society. Systematic design, service and management.
( 安全管理 )
单位：______________________
姓名：______________________
日期：______________________
编号：AQ-SN-0486
霍尼韦尔安全开关(通用版)
霍尼韦尔先进的开关传感技术使其在控制领域处于全球领导地位－特别是在工业安全领域。

我们提供电子机械安全开关和电子安全传感器以及安全控制模块给任何一种可能对使用者造成危险的应用环境。

客户完全可以在我们提供的产品系列中选择它们需要的全安全产品。

霍尼韦尔的产品都达到甚至超过了欧洲机械安全标准，而且得到了相关认证(CE，BG，INRS)，在欧洲使用超过了25年。

随着北美开始制定与全球相一致的标准，机器制造商和使用者可以完全信赖霍尼韦尔的机械安全解决方案。

我们的产品设计符合所有的OSHA和ANSI标准。

霍尼韦尔的扩展产品包括以下的电子机械安全产品:
安全互锁开关
安全限位开关
安全拉绳开关
接触模块选件
我们其他的安全产品包括:
电子安全传感器
安全控制模块
XXX图文设计
本文档文字均可以自由修改。

PRODUCT DATA65-0237-1CP-UM-5109E® U.S. Registered TrademarkCopyright © 2000 Honeywell Inc. • All Rights ReservedC6097A,BPressure SwitchesAPPLICATIONThe C6097 Pressure Switches are safety devices used in positive-pressure or differential-pressure systems to sense gas or air pressure changes.FEATURES•For use with natural gas, liquid propane (LP) gas, or air.•Diaphragm-actuated safety-limit switch.•Switch can be wired to turn on alarm.•C6097A models break control circuit at setpoint on pressure fall.•C6097B models break control circuit at setpoint on pressure rise.•Lockout with manual reset and recycle options.•Lockout models have external manual reset button.•Removable transparent cover protects scaleplate and adjusting knob.•Pipe tappings allow selection of positive pressure, differential pressure (air only) or venting connections (NPT mount only).•1/4 in. NPT or flange mount models for direct mounting to Honeywell Integrated Valve Train.•Optional switch position indicator lamp available.•IP54 enclosure standard.•Ranges: 0.4 to 5 in. wc, 3 to 21 in. wc, 12 to 60 in. wc or 1.5 to 7 psi.•Surge orifice.ContentsApplication ........................................................................1Features ...........................................................................1Specifications ...................................................................2Ordering Information ........................................................2Installation ........................................................................4Wiring ...............................................................................5Settings and Adjustments .................................................5Operation and Checkout ..................................................6C6097A,B PRESSURE SWITCHES65-0237—12ORDERING INFORMATIONWhen purchasing replacement and modernization products from your TRADELINE® wholesaler or distributor, refer to theTRADELINE® Catalog or price sheets for complete ordering number.If you have additional questions, need further information, or would like to comment on our products or services, please write or phone:1.Your local Home and Building Control Sales Office (check white pages of your phone directory).2.Home and Building Control Customer Logistics Honeywell Inc., 1885 Douglas Drive NorthMinneapolis, Minnesota 55422-4386 (612) 951-1000In Canada—Honeywell Limited/Honeywell Limitée, 155 Gordon Baker Road, North York, Ontario M2H 3N7.International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France, Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A.SPECIFICATIONSModels:C6097A Pressure Switch: Breaks a circuit when pressure falls to scale setting. See Table 1.C6097B Pressure Switch: Breaks a circuit when pressure rises to scale setting. See Table 1.Table 2 shows switch ratings and Table 3 shows alternate electrical ratings when used with Honeywell Flame Safeguard Programmers.Minimum Ambient Temperature: -40°F (-40°C).Maximum Ambient Temperature: 140°F (60°C).Connections (Depending on Model):1/4-18 NPT tapping for main or high-pressure connection.1/8-27 NPT tapping for vent or low-pressure connection (air only).Flange mount for connection to Honeywell Integrated Valve Train (internal vent only, no external connections).Scale Range:0.4 to 5 in. wc (0.10 kPa to 1.25 kPa).3 to 21 in. wc (0.75 to 5.23 kPa).12 to 60 in. wc (3.0 kPa to 15 kPa).1.5 to 7 psi (10.3 kPa to 48 kPa).Approvals:Underwriters Laboratories Inc. listed.Canadian Standards Association listed.Factory Mutual: Approved.Industrial Risk Insurers: Acceptable.CSD-1 AFB: Acceptable.Accessories:32003041-001 C6097 Cover for manual reset models.32003040-001 C6097 Cover for recycle models.32003039-001 Position Indication Lamp Kit.Dimensions: See Fig. 1 and 2.Fig. 1. C6097 1/4 in. NPT Mount dimensions in in. (mm).C6097A,B PRESSURE SWITCHES365-0237—1a Acceptable media: Natural gas, liquid propane (LP) gas, and air .Table 1. Pressure Switch Model Selection.Model Operating Pressure Range Manual Reset DifferentialNon-Manual ResetDifferentialDifferential Type Maximum Rated Pressure(continuous) (psi)Manual Reset Media a Switch Action at Setpoint Comments Maximumat Minimum Setpoint Maximumat MaximumSetpoint Nominal Maximum C6097A10040.4 to 5 in. wc——0.16 in. wc 0.24 in. wc Additive2.9 No Air/Gas Breaks N.O. to C.connection on pressure fall.1/4 in. NPT Mount C6097A1012 3 to 21 in. wc2.4 in. wc 4.2 in. wc —— 4.3Yes Air/Gas 1/4 in. NPT Mount C6097A1020 3 to 21 in. wc 2.4 in. wc 4.2 in. wc —— 4.3Yes Air/Gas Flange Mount C6097A103812 to 60 in. wc 10 in. wc 12 in. wc —— 4.8Yes Air/Gas 1/4 in. NPT Mount C6097A104612 to 60 in. wc10 in. wc12 in. wc—— 4.8Yes Air/Gas Flange Mount C6097A1053 3 to 21 in. wc—0.24 in. wc0.48 in. wc 4.3No Air/Gas 1/4 in. NPT Mount C6097A1061 3 to 21 in. wc ——0.24 in. wc0.48 in. wc4.3No Air/Gas Flange Mount C6097A107912 to 60 in. wc —— 1.1 in. wc 2.4 in. wc 4.8No Air/Gas 1/4 in. NPT Mount C6097A108712 to 60 in. wc—— 1.1 in. wc 2.4 in. wc 4.8No Air/Gas Flange Mount C6097A10950.4 to 5 in. wc 0.6 in. wc 1.0 in. wc —— 2.9Yes Air/Gas 1/4 in. NPT Mount C6097A1103 1.5 to 7 psi 1.1 psi 1.4 psi ——9.3Yes Air/Gas Flange Mount C6097A1111 1.5 to 7 psi 1.1 psi 1.4 psi ——9.3Yes Air/Gas 14 in. NPT Mount C6097A1129 1.5 to 7 psi ——0.1 psi 0.39.3No Air/Gas Flange Mount C6097A1137 1.5 to 7 psi——0.1 psi 0.39.3No Air/Gas 1/4 in. NPT Mount C6097A12100.4 to 5 in. wc——0.16 in. wc 0.24 in. wc 2.9No Air/Gas Flange Mount C6097A12280.4 to 5 in. wc ———— 2.9Yes Air/Gas Flange MountC6097B100212 to 60 in. wc 10 in. wc 12 in. wc ——Subtractive4.8Yes Air/Gas Breaks N.C. to C. connectionon pressure rise.1/4 in. NPT Mount C6097B101012 to 60 in. wc10 in. wc12 in. wc —— 4.8Yes Air/Gas Flange Mount C6097B1028 3 to 21 in. wc2.4 in. wc 4.2 in. wc —— 4.3Yes Air/Gas 1/4 in. NPT MountC6097B1036 3 to 21 in. wc 2.4 in. wc 4.2 in. wc —— 4.3Yes Air/Gas Flange Mount C6097B1044 1.5 to 7 psi 1.1 psi 1.4 psi ——21.0Yes Air/Gas Flange Mount C6097B1051 1.5 to 7 psi1.1 psi1.4 psi ——21.0Yes Air/Gas 1/4 in. NPT Mount C6097B1069 3 to 21 in. wc ——0.24 in. wc0.48 in. wc4.3No Air/Gas Flange Mount C6097B107712 to 60 in. wc —— 1.1 in. wc 2.4 in. wc 4.8No Air/Gas Flange Mount C6097B108512 to 60 in. wc —— 1.1 in. wc 2.4 in. wc 4.8No Air/Gas 1/4 in. NPT Mount C6097B1093 1.5 to 7 psi ——0.1 psi 0.3 psi 21.0No Air/Gas Flange Mount C6097B1101 1.5 to 7 psi——0.1 psi 0.3 psi 21.0No Air/Gas 1/4 in. NPT Mount C6097B11193 to 21 in. wc——0.24 in. wc0.48 in. wc4.3NoAir/Gas1/4 in. NPT MountC6097A,B PRESSURE SWITCHES65-0237—14Table 2. Switch Ratings (Amperes)Table 3. Alternate Electrical Ratings when used withHoneywell Flame Safeguard Programmers.Fig. 2. C6097 Flange Mount dimensions in in. (mm).INSTALLATIONWARNINGExplosion or Fire Hazard.Can cause severe personal injury, death or property damage.Observe all safety requirements each time a control is installed on a burner.When Installing this Product...1.Read these instructions carefully. Failure to follow them can damage the product or cause a hazardous condition.2.Check the ratings given in the instructions and on the product to make sure that the product is suitable for your application.3.Installer must be a trained, experienced service technician.4.After installation is completed, check out product operation as provided in these instructions.WARNINGElectrical Shock Hazard.Can cause serious personal injury or death.Disconnect power supply before beginning installation. More than one disconnection can be involved.MountingNOTE:On flange models, remove the label holding theO-ring in place and make sure O-ring seal is in place before mounting the pressure switch on the valve.The C6097 models allow NPT or flange (directly to valve) mounting. The NPT models have a hexagonal fitting with a 1/4 in. NPT tapping, which is the high pressure connection, in differential applications. The bleed fitting is 1/8 in. NPTtapped. In differential pressure control applications using air only, connect the lower pressure to the bleed fitting. See Fig. 1 and Table 1. In applications using combustible gases, vent the bleed tapping according to applicable standard code or jurisdictional authority.C6097 models with flange mount can be fitted directly toHoneywell Integrated Valve Train (model specific). See Fig. 2 and Table 1. The flange mount models vent internally, with no external tap.Mount the C6097A,B in any position.Leak CheckAfter installation, perform a leak check on the pressure switch:1.Turn on main gas. Make sure gas has reached thepressure switch (e.g., high gas pressure switch)2.Check installation for gas leaks using a gas leak detector or a soap solution.120/240 Vac, 50/60 HzInductive Full Load 3.0Locked Rotor18.0Resistive5.0DeviceRatingIgnition Transformer 540 VA Pilot Valve 50 VAMain Valve400 VA with 2-1/2 times inrush.C6097A,B PRESSURE SWITCHES565-0237—1WIRINGWARNINGElectrical Shock Hazard.Can cause serious personal injury or death.Disconnect power supply before beginning installation. More than one disconnection can be involved.Make sure that all wiring agrees with all applicable localcodes, ordinances and regulations. An opening is provided to accommodate rigid conduit or armored cable for line voltage operation (see Fig. 3 and 4). Do not overload the switch contacts (see Switch Ratings in the Specifications section). The switching schematic is shown in Fig. 5.Fig. 3. C6097 (manual reset switch model)with cover removed.Fig. 4. C6097 (recycle model) with cover removed.SETTINGS AND ADJUSTMENTSPressure Setpoint Adjustmentdial (Fig. 3, 4 and 5) clockwiseto decrease the pressure setting.Fig. 5. C6097 schematic.C6097A,B PRESSURE SWITCHES65-0237—16OPERATION AND CHECKOUTOperationThe manual reset C6097A diaphragm actuates the snap-acting switch to break a control circuit and lock out when pressure falls to the scale setting. The recycle C6097Amodels recycle automatically when the control circuit returns to scale setting plus differential.The manual reset C6097B diaphragm actuates the snap-acting switch that breaks a control circuit and locks out when the pressure rises to the scale setting. The recycle C6097B models recycle automatically when the control pressure falls to the scale setting minus differential.Manual ResettingThe C6097A manual reset models lock out when pressure falls to the scale setting and require manual resetting after the pressure rises to scale setting plus differential to resume normal operation.The C6097B manual reset models lock out when pressure rises to the scale setting and require manual resetting after the pressure falls to scale setting minus the differential to resume normal operation.To reset, once normal operating pressure is restored, push the reset button in as far as it goes, then release.IMPORTANTLockout models cannot be made to recycleautomatically by permanently holding in the reset lever.CheckoutC6097 Gas Fuel Application1.Set cutoff pressure.2.Open main supply line. Depress reset lever on lockout models until switch makes control circuit.3.Set controller and limit switch to call for heat.4.For C6097A: Close the manual gas shutoff valve. C6097 should open control circuit when pressure reaches cutoff point.For C6097B: Open the manual gas shutoff valve, wait a few minutes for the pressure to rise; then lower the scale setting until the switch breaks control circuit and locks out.5.For C6097A: Open the shutoff valve, return thepressure switch to its original setting and press the reset button (if necessary).For C6097B: raise setting to normal and press reset button (if necessary).6.Allow system to operate through at least one complete cycle to make sure all components are functioning properly.C6097A Air Application1.Set cutoff pressure.2.Turn on fan.3.Block fan inlet or filter area. Switch should break control circuit when pressure drops to cutoff point. Manual reset models lock out.4.Remove obstruction. Press reset lever (manual reset models) and allow system to operate through at least one complete cycle to be sure all components are functioning properly.765-0237—165-0237—1 G.R. Rev. 4-00Home and Building Control Home and Building ControlHoneywell Asia Pacific Inc.Honeywell Inc.Honeywell Limited-Honeywell Limitée Room 3213-3225Honeywell Plaza 155 Gordon Baker Road Sun Hung Kai Centre P.O. Box 524North York, Ontario No. 30 Harbour Road Minneapolis, MN 55408-0524M2H 3N7Wanchai Hong KongHoneywell Latin American Region Honeywell Europe S.A.480 Sawgrass Corporate Parkway 3 Avenue du Bourget Suite 2001140 Brussels Sunrise FL 33325Belgium。