X4脉冲款说明

一、概述XY-4型钻机是根据我国勘探技术发展的经验，结合我国地质工作的特点，设计试制成功的一种新型高速金刚石岩心钻机, 钻机外形图见图1。

该钻机于1976年1月通过了国家正式鉴定。

本厂生产的这种钻机于1988年荣获国家银质奖。

产品行销全国各地。

基本型XY-4型钻机配套动力为潍柴4100型柴油机或Y200L-4型30千瓦电动机。

根据用户需要也可选配相类似的柴油机或电动机。

XY-4型钻机具有最高达1588转每分的高速，同时也具有101转每分的低速，转速级数多达8级，因此该钻机的工艺适应性较强，使用范围较大，除主要用于地表及坑道对固体矿床的金刚石，硬质合金钻探外，可用于工程地质勘察，浅层石油，天然气，地下水钻探，也可用于堤坝注浆和坑道通风排水等工程孔钻进。

在推行标准化、系列化、通用化的过程中，我厂对该机全套图纸进行重新复核，贯彻执行了国家现行的最新标准，因此产品精度更加严密，同机型的互换性增强。

根据多数用户的要求，在贯标过程中将部分结构重新设计，性能更优越，并在地质系统内基本统一，为广大用户在使用、维护保养方面提供了方便。

XY-4型钻机与一般类型油压钻机比较具有下列特点：1、钻机具有较高的转速和较合理的转速范围，转速级数较多，低速扭矩大，适合小口径金刚石岩心钻进，也能满足大口径硬质合金岩心钻进和各种工程钻孔的要求。

2、钻机重量较轻，可拆性较好，钻机可分解成九个整体部件，最大部件仅218千克，便于搬迁，宜于山区工作。

3、结构简单，布局较合理，所有部件均表露在外，不相互重叠，便于维护，保养和修理。

4、钻机具有两个反转速度，处理事故时劳动强度不大，且安全。

钻机移车平稳，固定牢靠，钻机机架坚固，重心低，高速钻进时稳定性好。

5、配有仪表，利于掌握孔内情况，操作手柄较少，布局较合理，操纵灵活可靠。

6、钻机与泥浆泵采用单机分别传动，机场布置比较灵活，可减少机场面积。

二、技术规格和主要技术参数1、基本参数：钻孔深度用42毫米钻杆………………1000米(最深1200米)用50毫米钻杆…………………700米(最深850米) 钻孔倾角……………………………………………………..………360°外形尺寸(长×宽×高)……………………………...2710×1100×1750毫米钻机重量（不包括动力机）……………………………………1500千克最大部件重量……………………………………………………218千克2、回转器立轴转速：当动力机转速为1500转/分时正转低速……………………………………101；187；267；388 转/分高速………………………………… 311；574；819；1191 转/分反转低速……………………………………………………… 83 转/分高速………………………………………………………251 转/分当动力机转速为2000转/分时正转低速………………………………………135；250；355；517 转/分高速…………………………………415；765；1090；1588 转/分反转低速…………………………………………………………110转/分高速…………………………………………………………338转/分立轴行程…………………………………………………………600毫米立轴最大起重能力……………………………………………80000牛顿立轴最大加压能力……………………………………………60000牛顿立轴扭矩: 当动力机功率为40马力，转速为1500转/分时2640；1410；980；660牛顿²米830；440；300；200牛顿²米立轴内径……………………………………………………………68毫米3、卷扬机：当柴油机功率为40马力，转速为1500转/分时提升能力（单绳）…………………30000；16000；11000；7700牛顿提升速度（第三层）…………………….0.82；1.51；2.16；3.15米/秒当柴油机功率为60马力，转速为2000转/分时提升能力（单绳）…………………33000；17800；12450；8600牛顿提升速度（第三层）………………….…1.09；2.02；2.89；4.18米/秒钢丝绳直径…………………………………………………………16毫米卷筒容量……………………………………………………………90 米卷筒直径…………………………………………………………285毫米闸轮直径…………………………………………………………490毫米刹带宽度…………………………………………………………120毫米4、移动装置移动油缸行程……………………………………………………460毫米钻机离开孔口距离………………………………………………310毫米5、液压系统⑪、系统压力工作压力………………………………………………………..…8兆帕最高压力…………………………………………………………12兆帕⑫、油泵排量……………………………………………………………20毫升/转转速……………………………………………………………1500转/分工作压力…………………………………………………………20兆帕最高压力…………………………………………………………25兆帕6、钻机动力电动机柴油机柴油机型号Y200L-4 X4105BG26-15 ZH4100G43功率30千瓦35.3千瓦31千瓦转速1465转/分1500转/分1500转/分重量260千克670千克350千克三、钻机传动系统钻机传动系统见图2，动力机通过弹性联轴节、摩擦离合器将运动传至变速箱。

u 在 IPv4 和 IPv6 网络上提供高质量 H.264 视频u 占用较少带宽的自适应比特率编码u 一流的转码技术，适用于高级远程回放u 通过网络连接的 RAID iSCSI 存储设备u在 CF 卡上进行本地录像VideoJet X20/X40 XF E 编码器属于博世高性能、双路或四路输入 CCTV 视频编码器系列，可在 IPv4 和 IPv6 网络上提供实时 H.264 压缩视频。

在完全帧速率的情况下，这些装置可为每台摄像机提供两个高质量的独立视频流。

它们可用于不同用途，例如，一个视频流供您顺畅无延迟地实况查看，而另一个视频流经过优化后，只需占用很少的录制空间。

VideoJet X20/X40 XF E 编码器支持 PAL 和 NTSC 视频源，提供与视频同步的双向音频通信。

它们拥有精心设计的外壳，可以轻松安装在机架中或墙壁上。

这些设备功能强大且配置灵活，提供了当今 CCTV 领域中通过 IP 网络传输高性能视频的领先技术。

功能优异的灵活性VideoJet X20/X40 XF E 编码器提供出色的录像灵活性。

用户可以通过网络传输视频，然后使用网络录像机 (NVR) 存储视频。

在 CompactFlash 或网络连接的 RAID iSCSI 存储设备上执行本地录像。

内置 iSCSI 支持，使VideoJet X20/X40 XF E 设备既可以充当传统的 DVR ，又能通过网络传输高性能的实况视频。

三码流编码器采用Dual Streaming ，可为每条通道生成两个独立的 H.264 视频流。

这样，用户就能以两种不同的品质级别进行查看和录像，从而节省磁盘空间和带宽。

它们提供独立配置的 M‑JPEG 流作为第三个视频流，以便轻松与第三方集成。

当发生报警时，它们可以发送附带 JPEG 图像的电子邮件。

查看通过 Bosch Video Management System 中的 Web 浏览器查看 PC 机上的编码器视频，或将视频集成到其它视频管理系统中。

X4的操作步骤
(1)、按住开/关键2秒钟，仪器开机
(2)、执行自检
接下来屏幕显示如下：
·显示一级报警点（可燃气和有毒气，氧气高浓度报警） ·显示二级报警点（可燃气和有毒气，氧气低浓度报警） ·显示STEL 和TWA 报警点（只对一氧化碳和硫化氢）
当按下开/关键后，仪器将检查传感器，电路，电池，声音，灯光，振动报警。

仪器将执行如下：（1）显示所有的数字和字符提示信息
（2）检查声音，灯光，振动报警 （3）检查电池，电路和传感器
(3)、自检是否通过
另外，仪器将会定期的检查电池，电路和传感器。

！注意：如果自检失败，应重新进行自检，如果再次失败请联系当地代理/服务商。

(4)、进入测量模式
(5)、解除报警
自检通过
正常显示
报警提示符号将
警符号（一级）
报警提示符号将
警符号（二级）
(6)、关机
修改报警值步骤
（1）、打开仪器至正常显示 （2）、同时按住上/下键，直到声音响起后松手
（3）、再按上键或下键选择到报警值界面 （4）、再按开关键，选择需要设置的气体
（5）、按上键或下键进行报警值的设置
（5）都设置完了，等20秒仪器自动回到检测模式
如何装电池。

AVR-X4400H INTEGRATED NETWORK AV RECEIVER 操作说明书附件8安装电池9遥控器的操作范围9特点10高音效10高性能13简易操作17部件名称与功能18前面板18显示屏22后面板24遥控器28连接方法扬声器安装32连接扬声器40连接扬声器之前40扬声器配置和“放大器分配”设置44连接5.1声道扬声器46连接7.1声道扬声器47连接9.1声道扬声器51连接11.1声道扬声器59连接7.1声道扬声器：前置扬声器的双功放连接65连接7.1声道扬声器：第二对前置扬声器66连接多区域扬声器67连接电视机72连接1：配备了HDMI端子并兼容ARC（Audio Return Channel）的电视机73连接2：配备了HDMI端子且不兼容ARC（Audio Return Channel）的电视机74连接3 : 未配备HDMI端子的电视机75连接播放设备76连接机顶盒（卫星调谐器/有线电视）77连接DVD播放机或蓝光碟片播放机78连接兼容Denon Link HD功能的蓝光碟片播放机79连接摄像机或游戏机80连接电唱机81将USB存储设备连接至USB端口82连接FM/AM天线83连接至家庭网络（LAN）85有线LAN85无线局域网86连接外部控制设备87 REMOTE CONTROL插孔87 TRIGGER OUT 插口88连接电源线89播放基本操作91开启电源91选择输入源91调节音量92暂时关闭声音（静音）92播放DVD播放机/蓝光碟片播放机92播放USB存储设备93播放储存在USB存储设备上的文件94在蓝牙设备上收听音乐97从蓝牙设备播放音乐98与其他蓝牙设备配对100从蓝牙设备重新连接至本机101收听FM/AM广播102收听FM/AM广播103通过输入频率来进行调谐（直接调谐）104更改调谐模式（调谐模式）105自动调谐到电台并进行预设（自动预设记忆）105预设当前广播电台（预设记忆）106收听预设电台106指定预设广播电台的名称（预设名称）107跳过预设的广播电台（跳过预设）108取消跳过预设109收听网络电台110收听网络电台111播放存储在计算机或NAS中的文件112播放存储在计算机或NAS中的文件113获取 HEOS App116 HEOS账户117从流媒体音乐服务播放118在多个房间聆听相同的音乐121 AirPlay功能125从iPhone、iPod touch或iPad播放歌曲126从iTunes播放歌曲126选择多个扬声器（机器）127使用本机的遥控器进行iTunes的播放操作127在多个同步设备上播放iPhone、iPod touch或 iPad上的曲目 (AirPlay 2)128 QPlay功能129在本机上播放QQ音乐曲目129便捷功能130添加到HEOS最爱收藏131播放HEOS最爱收藏131删除HEOS最爱收藏132调节各声道的音量以与输入源相符（声道电平调节）133调节音调（音调）134音频播放过程中播放所需视频（视频选择）135根据您的观看环境调节图片质量（画面模式）136在所有区域中播放相同的音乐（所有区域立体声）137选择声音模式138选择声音模式139直通播放140纯直通播放140自动环绕播放141声音模式类型介绍142可为每个输入信号选择的声音模式146 HDMI控制功能150设置步骤150智能菜单功能151睡眠定时器功能153使用睡眠定时器154快速选择附加功能155调用设置156更改设定157 ZONE2（区域2）/ ZONE3（区域3）（分开的房间）中播放158连接区域158 ZONE2 （区域2） / ZONE3 （区域3）播放164设置菜单图166菜单操作170音频171对话音量调节171低音炮音量调节171低音同步172环绕参数172 Restorer178音频延迟179音量180 Audyssey®181图形 EQ184视频186画质调整186 HDMI设置188输出设置193分量视频输出196屏幕显示197 4K信号格式198 TV格式199输入200输入分配200源重命名202隐藏源203输入源电平203输入选择204扬声器205 Audyssey®设置205扬声器的设定步骤（Audyssey®设置）207出错信息213检索Audyssey®设置设定215手动设置216放大器分配216扬声器配置224距离229电平230交叉231低音232前置扬声器233双声道回放233网络236信息236连接236 Wi-Fi设置237设置239网络控制241友好名称241诊断242HEOS账户243您尚未登录243您已经登录243常规244语言244 ECO244区域2设置 / 区域3设置247区域重命名249快速选择名称249触发器输出1 / 触发器输出2250前显示屏250固件251信息254使用率数据255保存和读取256设置锁定256通过遥控器操作外部设备257注册预设代码258操作设备261初始化注册的预设代码264指定使用遥控器的操作区域264重设遥控器264提示提示266故障诊断268电源无法开启 / 电源关闭269使用遥控器无法执行操作270本机显示屏不显示内容270不发出声音271所需声音没有发出272声音中断或出现噪音274电视机上不显示视频275菜单屏幕不显示在电视机上277 AirPlay无法播放278USB存储设备无法播放279无法播放蓝牙设备280网络电台无法播放281计算机或NAS上的音乐文件无法播放282无法播放各种在线服务283 HDMI控制功能无效283无法连接至无线LAN网络284使用HDMI ZONE2时，设备无法正确运行285更新/升级错误消息286恢复出厂设置287恢复网络设置288保修和修理289附录关于HDMI290视频转换功能293播放USB存储设备295播放蓝牙设备296播放保存在计算机或NAS中的文件297播放网络收音机298个人记忆附加功能298最新功能记忆298声音模式和声道输出299声音模式和环绕参数301输入信号的类型和对应的声音模式304术语解释307商标信息316规格319索引325许可证328感谢您选购本款Denon产品。

USB-C/Charger1Push the tray back into your phone.Insert the nano SIM and memory cards.Insert the SIM card(s) with the gold contacts down.Insert an optional microSD Insert the SIM tool into the tray hole to pop out the tray.3Power on.Press and hold Power until the screen lights up.Before using your phone, fully charge it with the charger provided .Charge up .• To find lock/unlock settings, swipe up • To find navigation settings, swipe up Note:Home/Unlock Screen Recents Swipe right.Back Swipe left.5Find it:• Moto Actions:6PHOTOS SETTINGS7>get walk-through tutorials, how-tos, or FAQs, Here’s how to find us:Where is my legal, safety andCargador/USB-C1Vuelve a poner la bandeja en el teléfono.Introduce las tarjetas nano SIM y de memoria.Coloca la tarjeta SIM conlos contactos dorados hacia abajo. Inserta una Inserta la herramienta SIM en el agujero de la bandeja para sacarla.incorrecta, es posible que3Enciéndelo.Mantén presionado el botón de encendido hasta que la pantalla se ilumine.Antes de usar el teléfono, cárgalo completamente con el cargador proporcionado.Cárgalo.desbloqueo, desliza• Para encontrar la configuración de navegación, deslizaun botónDesbloquear Recientes Desliza hacia la derecha.Atrás Desliza hacia la izquierda.5Encuéntralo en:• Acciones Moto: usa gestos como atajos del6CONFIGURACIÓN FOTOS7• La ayuda está aquí:y presiona Ayuda del dispositivo obtener tutoriales paso a paso o ver las• Obtén aplicaciones:descargar aplicaciones.puedes encontrarnos en:¿Dónde encuentro información。

®《User Manual》H501APLEASE READ THE MANUAL CAREFULLY BEFORE USE.1.Quad + Phone/Pad2.Quad + Phone +Relay3.Quad + Transmitter+++orCaution:For safety, the quadcopter is default set to CAN NOT FLY WHEN NO GPS. If you prefer to fly when GPS is not available, please reset the value as instructed below before using.Pull the throttle stick to the lowest position and press the Elevator stick for 1.5 seconds to enter into the MAIN MENU interface. Push the Elevator stick up/down to select “Fly When no GPS”, push the stick right to enter into the “ Fly When no GPS” interface, select “YES”.The Default Setting is “NO”.Select “Exit” to exit.Compass calibration is required after the binding as instructed on the transmitter.1 ) Horizontally rotate the X4 in a clockwise direction when the LCD screen shows “Calib compass 1”2 ) Put the X4 nose down and vertically rotate it in a clockwise direction when the LCD screen shows “Calib compass 2”3 ) Calibration is completed when the4 LED indicators remain solid.Important safety notesOperation: Be extremely careful and responsible when using the quad. Small electronic components can be damaged due to crashes or exposure to water. To avoid any injuries, do not use the quad with broken or damaged components.Maintenance: Do not try to fix the quad yourself, please contact authorized distributors for service. For more information, please visit the official website at .Battery: Battery: Do not store the battery in high temperature area (60 ℃or higher). Using a Hubsan dedicated charger for recharging.Keep the batteries away from children.Keep the batteries dry.USAGE ADVICEHubsan provides you with two files for your quad:1.《Disclaimer》2.《Quick Start Guide》Watch the tutorial video and read the Disclaimer first,.For detail information, please download User Manual at .Read the Disclaimer first before use.※Symbol explanation1- Do not fly the quad in a crowded area, always be aware of the safety of yourself and others.- Do not fly in bad weather condition.- Do not try to catch the quadcopter while it is still in flight.- This product is intended for experienced pilots over the age of 14.- Remove the battery when it is not in use, to avoid accidental injuries.- Keep your body away from the propellers after powered on. High speed propellers are very dangerous.No operatingImportant NoticeInstructionExplanation, referenceSafety Advisory Notice for Lithium-Polymer (LIPO) Batteries LiPo batteries are different from conventional batteries in that their chemical contents are encased in a relatively lightweight foil packaging. This has the advantage of significantly reducing their weight but it does make them more susceptible to damage if roughly or inappropriately handled. As with all batteries, there is a risk of fire or explosion if safety practices are ignored:● If you do not plan to fly the quad for a long time, store the battery approximately 50%charged to maintain battery performance and battery life.● Please use Hubsan chargers for battery charging.● Discharging the battery within 5C current , do not over-discharging.● Do not charge on carpet to avoid fire.● Batteried need to be recharged if not in use for over 3 months.1.Charge and store LiPo batteries in a location where a battery fire or explosion(including smoke hazard) will not endanger life or property.2.Keep LiPo batteries away from children and animals.3.Never charge the LiPo battery that has ballooned or swelled.4.Never charge the LiPo battery that has been punctured or damaged.5.After a crash, inspect the battery pack for signs of damage. Discard in accordancewith your country’s recycling laws.6.Never charge the LiPo battery in a moving vehicle.7.Never overcharge the LiPo battery.8.Never leave the LiPo battery unattended during recharging9.Do not charge LiPo batteries near flammable materials or liquids.10.Ensure that charging leads are connected correctly. Reverse polarity charging canlead to battery damage or a fire or explosion.11.Have a suitable fire extinguisher (electrical type) OR a large bucket of dry sand nearthe charging area . Do not try to extinguish electrical (LiPo) battery fires with water.12.Reduce risks from fire/explosion by storing and charging LiPo batteries inside asuitable container.13.Protect your LiPo battery from accidental damage during storage and transportation.(Do not put battery packs in pockets or bags where they can short circuit or can come into contact with sharp or metallic objects.).14.If your LiPo battery is subjected to a shock (such as a crash), place it in a metalcontainer and observe for signs of swelling or heating for at least 30 minutes.15.Do not attempt to disassemble or modify or repair the LiPo battery.2Contents3IMPORTANT SAFETY NOTES INTRODUCTIONSYMBOL EXPLANATION 1.ITEMS INCLUDED IN THE BOX USAGE ADVICE 2QUAD COPTER 3QUAD COPTER BATTERY 4PROPELLERS 6 TRANSMITTER3.1INTRODUCTION4.1INTRODUCTION4.2 INSTALLING THE PROPELLERS 6.1 INTRODUCTION6.1.1 TRANSMITTER KEY FUNCTION3.2INSTALL THE BATTERY 3.3CHARGING 2.1QUAD COPTER MOTOR LED INDICATOR 1121211211341341355131313141555561515176617171818191920202223678107107117125 X-Hubsan App 6.1.2 INSTALL THE TRANSMITTER BATTERY 6.1.3 TRANSMITTER STICK CALIBRATION 6.1.4 ADJUSTABLE 5.8GHZ FREQUENCY 6.1.5 ANTENNA INSTRUCTION 7 START TO FLY7.1 FLIGHT ENVIRONMENT7.2 SAFETY CHECK BEFORE FLIGHT7.3 FLY WITH APP7.3.1 CONNECT THE QUADCOPTER WITH APP7.3.2 COMPASS CALIBRATION 7.4 FLY WITH TRANSMITTER 7.4.1 BIND THE QUAD WITH TRANSMITTER7.4.2 COMPASS CALIBRATION7.4.3 HORIZONTAL CALIBRATION 7.4.4 ROTATION CALIBRATION 7.4.5 START/ STOP THE MOTORS 7.4.6 BASIC FLIGHT8 ADVANCED PERFORMANCE SETUP 8.1 REVERSING CHANNEL SETUP 8.2 SENSITIVITY SET UP8.3 HEADLESS MODE8.4 FOLLOW ME MODE8.5 HOME MODE 8.6 EXIT HOME MODE9 FAILSAFE MODEH501A TROUBLESHOOTING SCHEMATIC DIAGRAM H501A Spare Part Chart4.3 REMOVING THE PROPELLERSIntroductionThank you for buying the HUBSAN product. It is designed as an easy-to-use, multi-functional RC model, capable of hovering and acrobatic flight maneuvers. Please read the manual carefully and follow all the instructions. Be sure to keep the manual for future reference.FPV：FFirst Person View，this feature enables you to experience every live moment of the flight from the drone's point of view.371PC 2PCSLi-Po battery User Manual For quad copter《Disclaimer》《Quick Start Guide》3Quadcopter battery3.1 IntroductionThe quadcopter battery is a rechargeable Li-Po battery with 2700mAh capacity and 7.4V voltage.The battery should only be charged with Hubsan charger to avoid overcharge.2.1 Quadcopter motor LED indicatorFront LED is blue; Back LED is red.1.Power on: 4 LED indicators blink simultaneously.pass Calibration:1). Horizontal calibration: 4 LED indicators blink circularly. 2). Vertical calibration: 4 LED indicators blink alternately .3.Quadcopter Horizontal Calibration: 4 LED indicators blink slowly.4.Quadcopter Rotation Calibration: 4 LED indicators blink circularly.5.GPS Flight: 4 LED indicators will remain solid.6.Low Voltage Return : 2 front LED indicators remain solid, and 2 back LED indicators blink quickly.7.Signal Lost: 2 front LED indicators blink alternately, 2 back LED indicators remain solid.8.LED indicators can be turned off by long pressing the lower throttle trim on the transmitter.3.2 Installing the battery167234895Propeller B Lower Body Shell 1080P Camera Propeller A Motor LED Light Battery CompartmentTF Slot[10]Upper Body ShellRubber Feet4 Propellers4.1 IntroductionThe quadcopter uses 7.3 inches propellers which are marked by A and B.3.3 ChargingConnect the battery to the balance charger and the wall charger. The left LED indicator on the balance charger will remain red and the right LED indicator will remain off when charging. The battery is fully charged when the right LED indicator turns green. It takes approximately 180 minutes to fully charge the battery.Please take off the charger and the battery when the battery is fully charged.4.3 Removing the propellersHold the motor with the wrench, then spin the propellers in the indicated unlock direction.●Make sure that the A and B propellers areinstalled correctly. The X4 will not fly if propellers are improperly installed.●Keep the moving propellers away from yourbody as well as other people and any obstacles.7Hubsan H901A is a multi-functional FPV transmitter with 3.7inch LCD screen and 5.8G live stream.Recommended maximum flight distance: 300m.6.1 Introduction6 Transmitter拍摄状态5 X-Hubsan AppHubsan designed an APP to go with the new X-Hubsan H501A. Users can use the APP to control the quad, take picture/videos and set the parameters of the quad. It is recommended to fly the quad within 100 meters and use smart devices with larger screen for the best visual experience.Camera Status Recording timeTransmitter's battery voltage Quad copter's battery voltage Quad copter's head dataQuad copter's roll Quad copter's pitchQuad copter's speed Quad copter's distance Quad copter's altitudeQuad copter's GPS signal strength Transmitter's GPS signal strengthLongitude & Latitude6.1.1 Transmitter key function9MODE 117 2.4G127MODE 289Throttle/Rudder stickElevator/Aileron stick Throttle/Aileron stickElevator/Rudder stick Aileron trim button Rudder trim buttonUp/Down T1、T2Headless mode switchGPS SwitchHome SwitchFollow Me SwitchThrottle trim button Power Switch Video/ENTER buttonPhoto/EXIT button Elevator trim button Push the stick forward or backward and the quadcopter willascend or decend; Push the stick left or right and the quadcopter will rotate in counter clockwise or in clockwisePush the stick forward or backward and the quadcopter will flyforward or backward;Push the stick left or right and the quadcopter will fly left or rightPush the stick forward or backward and the quadcopter will flyforward or backward;Push the stick left or right and the quadcopter will rotate in counter clockwise or in clockwise.Push the stick forward or backward and the quadcopter willascend or decend; Push the stick left or right and the quadcopter will fly left or right.Aileron trim adjusts for left and right drift.Rudder trim adjusts for drift of left and right rotation or yaw.To select settings.No FunctionPush up to enter headless mode;Push down to exit headless mode.Push up to activate GPS function;Push down to disactivate GPS function.Push up to turn on automatic return home;Push down to exit.Push the switch up, the follow me function will be activatedThrottle trim is normally at the center.Push to ON to turn on the transmitter. Push to OFF to turn off.Long press to enter Main Menu Short press to take videoLong press to exit Main Menu Short press to take photo Elevator trim adjusts for forward and backward drift.12(2)4635789101112131415(1)S/NMode/ ControlFunction6.1.2 Install the transmitter battery6.1.3 Transmitter stick calibrationMode 1: Push the left stick to the upper left corner and the right stick to the upper right corner then power on the transmitter simultaneously, Rotate both sticks in circles for three times when the LCD screen displays “Calibrate Stick” then release both sticks and press “Exit” until one beep sound is made, indicating a successful calibration.Mode 2: Push both sticks to the upper left corner then power on the transmitter simultaneously. Rotate both sticks in circles for three times when the LCD screen displays “Calibrate Stick” then release both sticks and press “Exit” until one beep sound is made, indicating a successful calibration.1016171819LCD 2.4G Antenna 5.8G AntennaStrap fastenerDisplay flight data and live streamTransmit control signalsReceive the video transmission To fasten the strap on tansmitterRemove the coverInstall 8 x AA batteriesaccording to the correct polaritiesClose the cover6.1.4 Adjustable 5.8GHz frequencyThe transmitter will automatically find the best frequency to ensure a good quality live video.When necessary, adjust the 5.8GHz frequency for a better video transmission.To adjust 5.8GHz frequency:Pull the throttle stick down to the lowest position and long press the ‘Enter’ button to open the ‘Main Menu’ interface. Use the Up/Down keys to select 5.8G frequency then press ‘Enter’ and switch between different frequency with Up and Down keys. Long pressThe transmitter mode can be shifted according to the above operation.11Mode 2/Mode1Mode 2/Mode1126.1.5 Antenna instructionFor maximum communication range, the 2.4G antenna should point skyward without obstructions in between; the 5.8G antenna should be bent vertically and have the side with‘Hubsan’ logo pointing at the quadcopter. The maximum range of the video transmission is approximately 300 meters.In case of any injuries caused by improper operations, it is recommended that beginners learn to operate the quadcopter under the guidance of an experienced user. It is also very important to choose a proper flight environment.7.1 Flight environment7.2 Safety check before flight(1) The flying area should be wide open and should be without any tall buildings, otherwise the GPS may not work.(2) Do not fly in bad weather condition such as windy, snowy, rainy or foggy weathers.(3) Avoid flying near obstacles, crowds, power cables, trees and water.(4) Do not fly near any radio towers or airports.(5) The quad will not work in the Antarctic Circle or the Arctic Circle.(6) Obey the local laws and regulations, do not fly in restricted areas.(7) Only fly in good weather conditions and between the temperature of 0-40℃ .(1) Make sure the batteries are fully charged. (Quad,transmitter or smart device)(2) Make sure propellers are installed properly.(3) Insert Micro-SD card for pictures and videos.(4) Check if motors work well after binding.Airport7.3.2 Compass CalibrationCompass calibration is required before the first flight, otherwise the compass may not work properly. The compass is very sensitive to the electromagnetic interference which can create false compass data and lead to poor flight performance or even flight failure. Calibrate the compass regularly can help to provide the optimal performance of the quad.7.3 Fly with AppAPP flight is only availabe when fly in outdoors.7.3.1 Connect the Quadcopter with App1.Power on the quad;2.Search for WI-FI on devices:For iPhone or iPad, please select【 Settings 】>Wi-Fi;For Android system,please select【 Settings 】>WLAN> W-Fi.3.Click HUBSAN_H501A_XXXXXX,and password is 12345678.The password cannot be changed by user.4.Connection completed5.Open X-Hubsan APP , choose Hubsan H501A to enter into the user interface for flight.NOTICE：For safety,please don't use the smart device for other purposes while it is connecting with Hubsan App.If you want to control the quad with other devices, please restart the quad.137.4 Fly with transmitter7.4.1 Bind the quad with transmitterThe binding process is completed in the factory.For re-binding, press Enter button and power on the transmitter simultaneously until “Bind to Plane” is displayed, then power on the drone and place it very close to the transmitter, the binding process will be completed after one “beep” sound.If the binding failed, please power off the drone and repeat the above steps.7.4.2 Compass calibrationCompass calibration is required before the first flight, otherwise the compass may not work properly. The compass is very sensitive to the electromagnetic interference which can create false compass data and lead to poor flight performance or even flight failure. Calibrate the compass regularly can help to provide the optimal performance of the quad.Do not calibrate the compass in a strong magnetic fieldDo not carry ferromagnetic materials with you while calibrating the compass,such as keys, cell phones, etc.Compass calibration procedures:1) Pull the left stick to the left side, and move the right stick from left to right quickly and repeat until the transmitter displays “Calib compass1”, and the 4 LED indicators blink circularly.2) Horizontally rotate the X4 in a clockwise direction until the LCD screen shows “Calib compass 2”, and the 4 LED indicators blink alternately.3) Put the X4 nose down and vertically rotate it in a clockwise direction until the “Calib compass 2” disappears.4) Calibration is completed when the 4 LED indicators remain solid.14Please follow the calibrating procedures:1) Push the left stick to the most right side, and move the right stick from left to right quickly until the 4 LED indicators blink slowly2) Calibration is completed whrn the 4 LED indicators stop blinking.StartC o m p l e t e7.4.4 Rotation calibrationRotation calibration is required when the quadcopter yaw during flight.Please follow the calibrating procedures:1) Push the left stick up, and move the right stick from left to right quickly until the 4 LED indicators blink slowly ;2) When the 4 LED indicators blink circularly, horizontally rotate the X4 in a clockwise direction until the 4 LED indicators remain solid temporarily;3) The 4 LED indictors will blink circularly again, repeat step 2 to rotate the X4;4) Calibration is completed whrn the 4 LED indicators stop blinking.157.4.5 Start/stop the motorsPull both sticks to the lower outer corner as shownon the picture to start or stop the motors.Push the throttle stick up slowly to take off;Push the throttle stick down slowly to land.7.4.6 Basic flightThe operations of the controller are based on Mode 2.The left stick controls the altitude and rudder of quadcopter, and the right stick controls its forward, backward, left and right flight.开始左边摇杆向上打到最大量程快速上下拨动右边摇杆直到航向灯慢闪当航向灯循环环形闪烁时，水平旋转飞行器直到航向灯变为慢闪重复上述动作直到航向灯变为长亮Caution:Keep the moving propellers away from your body as well as other people and any obstacles.Do not let go of the controller until the motors have fully stopped.Do not stop the motors during the flight to avoid crashing, unless for emergency.Start Push the left stick up Move the right stick from left to right quickly until the 4 LED indicators blink slowlyHorizontally rotate the X4 in a clockwise direction Continue to horizontally rotate the X4 in a clockwise direction168 Advanced performance setup8.1 Reversing channel setupIf you would like to reverse any of the stick functions due to personal preference, then follow the instructions below. Be aware that this will reverse the control commands.Pull the throttle stick down to the lowest position and long press the ‘Enter’ button to open the ‘Main Menu’ interface. Use the Up/Down keys to select ‘Set reverse’ and use ‘Enter’ button to switch between modes. Long press ‘Exit’ button to save and exit.178.2 Sensitivity setupIf you would like to adjust the sensitivity of any stick functions, then follow the instructions below.Pull the throttle stick down to the lowest position and long press the ‘Enter’ button to open the ‘Main Menu’ interface. Use the Up/Down keys to select ‘Set sensitive’ and use ‘Enter’ button to switch between ‘Expert mode’ and ‘Normal Mode’. Long press ‘Exit’ button to save and exit.8.3 Headless modeHeadless mode means the X4 will default the current head direction as its head when enterThe transmitter has a built-in GPS module. The Follow Me mode only works when bothPush the A switch up to enter Headless mode and push the A switch down to cancel Headless mode.The Head data displays in red when the quad copter enters into headless mode.The Head data displays in green when the quad copter exits headless mode.188.4 Follow me modePush the B switch up to enter Follow Me mode and push the B switch down to cancel Follow Me mode.When the switch is pushed up, the screen will display ‘Follow Mode’ in green and the quadcopter will turn and have the camera pointing at the transmitter. Only the throttle stick will still function under Follow Me mode.8.5 Home modeThe Return to Home mode will only work when both the quadcopter and the transmitter have 6 or more satellites.Enter into home modequadcopter.8.6 Exit home modeare armed19 automatically.9 Failsafe modeThe quadcopter will enter Failsafe mode when the connection between the transmitter is lost or when the power is low. The flight control system will control the quadcopter to return to the Home Point and land automatically. The Failsafe mode helps to avoid injuries or damages.H501A TROUBLESHOOTING1. Transmitter and X4 do not pair 1) Check if the transmitter and the X4 are both power on or not. 2) Re-pair by the following steps 1 Power off the transmitter.2 Press the camera function key and power on the transmitter till “Bing to plane” displays on the LCD screen.3 Face the X4’s bottom to the transmitter’s LCD screen very closely and power on the X4, hold 5 seconds till the pair is finished.2. Cannot Unlock the propellers 1) Make sure the X4 is finished the compass calibration. 2) Make sure the Home switch is in the downward position. 3) Make sure the sticks are all in the center positions.3. Cannot Search GPS Signals Make sure not fly indoor or fly surround by buildings. Make sure fly in outdoor and in an open field and void of obstacles, tall building or steel structures.(1) Transmitter is powered off.(2) The flight distance is over the signal transmission range of the transmitter.(3) The signal of the transmitter was interrupted by some other strong electronic interference.Home Point is recorded when the quadcopter receives the 6th satellite while the motors are armed.To ensure that the X4 can return safely to its Home Point, fly the X4 in a safe to fly area.If there are GPS satellites drops below 6 or less for more than 20 seconds while the X4 is returning home, the X4 will descend automatically.The X4 cannot avoid obstacles automatically while in Failsafe mode.If the power is low, please land the quadcopter in case of any damages.20Conditions that will activate Failsafe mode4. No Video or Video is Under Strong Interference1)Check if any strong interference sources around or not2)Check if the frequencies of the X4 and the transmitter are under cross interference ornot. (If so,please re-pair the X4 and the transmitter)5. Cannot HoverCheck if the barometric parameters displayed on the transmitter are correct or not.Check if the sticks are in the center position or not. (If not, please push the sticks to thecenterpositions)6. Cannot Flight In a Set-WaypointMake sure the GPS switch is in upper position.Make sure the GPS satellites are up to 6 or above.Make sure all the sticks are in the center positions, except the throttle stick.7. Follow Mode Function Not WorkMake sure the GPS and follow mode switches are in upper positions.Make sure the GPS satellites are up to 6 or above.Make sure all the sticks are in the center positions, except the throttle stick.Make sure 5 meters at least between the X4 and the transmitter.8. Cannot fly back to Home Point!Be sure the GPS satellites are more than 6 before flying.9. GPS signal lost!Check if there is any interference to quad or not, for example: high-tension cables, radio tower.10. The quad or video shakes while flying① Check the propellers, replace propellers if there is any brok en or deformed;② Check the screws on quadcopter are fixed in place or not;③ Check the motor shaft is broken or not.11. Cannot take pictures or videos!① Check if the Micro-SD card is inserted or not.② Check if the Micro-SD card is formatted correctly or not (For mat the Mirco-SD card before use, if the Micro-SD card is with FAT32, the card should be Cla ss 4 or Class 4+)12. Cannot connect with Wi-FiRestart the quadcopter.13. If you want to use the relay during flight, please unbind the quadcopter with the APP, otherwise the relay cannot be connected.2122H501A Spare Part ChartH501A-01 Body Shell- BlackH501S-18 Motor LED LampshadeA/BH501S-05B Propeller A- BlackH501S-08 Brushless Motor BH501S-01Body Shell- WhiteH109-04Rubber FeetH501S-06Propeller B- GoldH501S-19ESCH501S-17Eye LampshadeH501S-04ScrewH501S-06BPropeller B- BlackH501C-10LED PCBA(Blue/Red)H501S-03CanopyH501S-05Propeller A- GoldH501S-07Brushless Motor AH501A-02Flight Control PCBA23H501A-035.8G TransmissionModuleH501S-25H901A TX Li-Po BatteryH501A-05GPS ModuleH501S-27H906A TXH301S-11Adapter H501S-26USB CableH501S-13Compass ModuleH301S-12Balance ChargerH501A-04HT005 RelayH501S-14Li-Po BatteryH501S-16Propeller Wrench H501C-02Battery Cover24 Hubsan T echnology Company Limited。

条码标签打印机GX4-800使用手册版次：1.0日期：2021年2月22日使用手册修订记录GX4-800使用手册专属声明本手册包含立象科技股份有限公司拥有之专属信息。

这些信息仅供负责操作及维护手册中所述之设备的相关人士参考及使用。

未经过立象科技股份有限公司书面同意，不论任何情况下均不得对此类专属信息进行使用、再制，或揭露给任何第三方。

产品改良持续改良产品是立象科技股份有限公司奉行的原则之一。

所有的规格及符号得随时变更，恕不事先通知。

FCC 相容声明本设备经过测试并判定符合FCC 条例第15 篇对 A 级数位设备之限制。

该限制是为了提供合理保护，避免在住宅内使用时引起有害干扰而设计的使用条件。

本设备会产生、使用并发射调频能量，若未按指示进行安装与使用，可能会对无线电通讯造成有害干扰。

然而，我们不保证某些特定的安装方式不会发生干扰。

如果本设备对收音机或电视接收造成干扰(可经由打开或关闭本设备而确认)，则使用者可尝试利用下列方式进行调整：∙移动接收天线的角度或位置。

∙增加设备与接收器之间的距离。

∙将设备连接到不同电路上的其他插座。

∙如需协助，请洽询经销商或专业的收音机/电视技术人员。

本产品的外围装置均经过屏蔽传输线测试。

本产品必须使用屏蔽传输线，以确保符合相关规范。

未经立象科技股份有限公司明确许可的情况下，对设备进行的任何变更或修改都可能导致使用者丧失操作本设备之权利。

赔偿声明立象科技股份有限公司已采取必要步骤，确保本公司所发行之设计规格及手册的正确性；但这些出版品仍可能存在错误。

立象科技股份有限公司将保留修改任何此类错误之权利，并声明免除任何相关的赔偿责任。

不论任何情况下，立象科技股份有限公司或与随附产品(包含软硬件) 的制作、生产或运送程序相关之人士，均不对因使用本产品，或因无法使用本产品所导致的任何损害(包括但不限于商机损失、业务中断、商业信息损失或，其他金钱损失所造成的任何损害) 负赔偿责任，不论立象科技股份有限公司是否已被告知此等情事。

GX4用户手册目录声明 (3)声明/担保与赔偿 (3)安全操作概要 (3)安装安全概要 (4)第1章产品简介 (5)1.1随附配件 (5)1.2产品概述 (6)1.2.1后面板 (7)1.2.2前面板 (8)1.2.3外形尺寸图 (10)第2章产品安装 (11)2.1插入信号源 (11)2.2插入电源 (11)2.3设备上电 (11)第3章产品使用 (12)3.1使用菜单键 (12)3.2菜单结构 (12)3.3使用菜单 (13)3.3.1LED屏体配置 (13)3.3.2输入 (17)3.3.3输出 (19)3.3.4特效切换 (24)3.3.5音频设置 (25)3.3.6拼接功能 (26)3.3.7系统设置 (26)3.3.8语言LANGUAGE (28)3.3.9工厂复位 (28)3.4按键操作 (28)3.4.1TAKE (28)3.4.2PIP (29)3.4.3SCALE (29)3.4.4SAVE (30)3.4.5LOAD (31)3.4.6BLACK (31)第4章订购编码 (32)4.1产品 (32)4.2选配模块 (32)4.2.1输入模块 (32)第5章技术支持 (33)5.1联系我们 (33)第6章附录 (34)6.1规格 (34)6.2上载LED屏配置文件 (37)6.3术语和定义 (45)6.3修订记录 (52)首先感谢您选购我们的产品！为了让您迅速掌握如何使用这款视频处理器，我们为您送上了详细的产品使用手册。

您可以在使用视频处理器之前阅读产品介绍以及使用方法，请仔细阅读我们所提供给您的所有信息，以便于您正确地使用我们的产品。

声明声明/担保与赔偿声明该设备经过严格测试，符合电子类数码设备的标准，根据FCC第15部分的规定，这些限制是为了合理地防止设备在商业环境中操作时的有害干扰。

如果没有安装和使用规定的指导手册，该设备的产生、使用和放射无线电频率，可能会对无线电通讯造成有害干扰。

SECTION 1: PARTS & CHECKLISTX4 DEVICE MICRO USB™ CABLE MICRO USB™ CABLE HDMI/OBD II CABLESECTION 4: UPDATING YOUR X4 DEVICEINSTALLING THE UPDATER SOFTWARE1. Go to: and click “Support” tab at the top ofthe page.1. Locate and click the "SCT Software" option and thenclick on "Downloads". You will see "Device Updater".Click to begin downloading and installing onyour computer.2. Wait for that program to download, then double click and“Run” the SCTDeviceUpdater.exe file if it does notopen automatically.3. Follow the on-screen directions of the SCT DeviceUpdate Software Installer until it allows you toclick “Finish”.4. Follow the on-screen directions of the SCT DriversInstaller until it allows you to click “Finish”.5. Your SCT Device Updater Software and Drivers arenow fully installed and ready for use.UPDATING YOUR X41. Prior to updating your X4 you will need to return thevehicle back to stock, if not at stock already.2. Connect your X4 to your Windows™ based PC using theprovided Micro USB™ cable. Unfortunately, we do notoffer support for Apple computers at this time.3. Double click and open the SCT Device UpdaterSoftware.4. Click “Automatically Check for Updates”.5. Confirm the update by pressing the “Update Now”button. The update will now begin.6. Let the updater run until it says “Your device is now upto date”.7. You may now unplug your device from your computerand load a tune to your vehicle.QUICK START GUIDESECTION 5:READING VEHICLE VIN ANDSTRATEGY/OS PART#sFrom the Main Menu,select Vehicle Info.Once on the Vehicle Infoscreen, you’ll be asked to turnthe key on. The VIN# will displayas well as the Strategy for Fordvehicle/device. GM vehicle/device, will display the OSPart Numbers.SECTION 6:CHECKING/CLEARING VEHICLETROUBLE CODESFrom the Main Menu,select Vehicle Functions.Within this menu, you will begiven the option to read orclear DTCs (Diagnostic TroubleCodes). Finally, make yourselection and follow theon-screen prompts.SECTION 7:PROGRAMMING THE VEHICLE POWERING ON THE X4To power up your device using the provided HDMI to OBDII cable, connect to the vehicle’s OBDII port. The OBDII port is most commonly found within 24” of the steering column under the driver’s side dash.BEGIN PROGRAMMING1. From the Main Menu, selectProgram Vehicle.2. At this point, the key shouldbe in the ignition, but in theOFF position until promptedto turn key ON/RUN position.Within Program Vehicle, there are 2-3 selections depend-ing on the state of the vehicle.• Pre-Loaded Tune Files = Preloaded SCT tunes for useon stock vehicles only.• Custom Tune = Custom Tuning Dealer files, if there areany on the device.• Return to Stock = Restore original factory file to vehicle.USING PRE-LOADED TUNE FILESOnce you follow the first “Key On” prompt, the device will show you a selection of vehicles andengine sizes. Select yours here. This will take you to Adjustable Options where you will be able toadjust to different performance levels, vehicle characteristics, and options including, but not limitedto, speed limiters, axle ratio and tire size. (Adjustable Options are vehicle specific). For more infor-mation on Adjustable Options, please see the Adjustable Options Explained section of this guide.USING CUSTOM TUNESTo install Custom Tunes, select Program Vehicle, and scroll down to the Custom Tunes section. If your device contains anycustom tunes for your vehicle, this is where they will be listed. Once you’ve found your desired tune select it by highlighting it onthe menu and then pressing the center button on the X4 to choose the tune. Next, follow the on-screen instructions to load thetune to your vehicle. If no custom tunes are listed the device will refer you to our website to find a custom tuning dealer.RETURNING TO STOCKWith SCT devices, your stock file is stored during the initial programming. The stock file stays on the programmer untilreturned to stock. From Program Vehicle, select Return to Stock and follow the on-screen instructions to advance through theprogramming process.MAIN MENUPROGRAM VEHICLEGAUGES / DATALOGVEHICLE FUNCTIONSVEHICLE INFODEVICE INFODEVICE SETTINGSMAIN MENUPROGRAM VEHICLEGAUGES / DATALOGVEHICLE FUNCTIONSVEHICLE INFODEVICE INFODEVICE SETTINGSMAIN MENUPROGRAM VEHICLEGAUGES / DATALOGVEHICLE FUNCTIONSVEHICLE INFODEVICE INFODEVICE SETTINGSPROGRAM VEHICLEFUEL OCTANE93 0CTANE91 OCTANE87 OCTANEFuse Puller | Voltage T ester | Battery Charger | PliersTOOLS NEEDED:SECTION 3: IMPORTANT ON-DEVICE INFO. From the Main Menu, select Device Info.Within Device Info, you will find :SERIAL NUMBER:Needed for dealers to create custom tunes for your vehi-cle and device.FIRMWARE VERSION:This is essentially your device’s operating system. TUNE REVISIONThe version number of your preloaded tunes. UNLOCKS LEFT:Number of unlocks remaining. An unlock is used when the tuned vehicle is returned to stock and a different vehicle is programmed.MARRIED STATUS:Unmarried = Unlocked and ready for vehicle pairing. Married = Locked to a vehicle.VBATT:The amount of voltage being run through the device from your vehicle’s battery. As a general rule, 12.75+ volts is needed to flash a tune to a vehicle.NOTE: Make sure the X4 is unplugged from yourcomputer before starting this process.NOTE: Custom Tunes are built by SCT’s network of Custom Tuning Dealers and any questions related to themneed to be directed toward the tuning dealer.NOTE: Please make sure that all stock electronics are turned off and disconnect any aftermarket electronics as well. Two clicks SECTION 2:PRE-INSTALL CHECKLIST INTERNET ACCESSIn the unlikely event that technical support is needed, Internet access may be required to troubleshoot. Our Technical Support team may also need to remotely connect to your computer to fix any issues you may be having. ALLOW TIME FOR INITIAL SETUPMake sure you allow up to 30 minutes to complete the initial setup and installation.NEED FURTHER SUPPORT?For additional troubleshooting and support, see our knowledge base on-line at /support.Alterations made to the OEM configuration ofa vehicle may violate the Clean Air Act if such alterations bypass, defeat, or render inoperativeElements of Design installed on a vehicle in compliance with the Clean Air Act. Users who alter Derive’s products in any way are required to make their own individual determination that the altered products do not violate the Clean Air Act. This device is not legal for sale or use in California on pollution controlled vehicles.SECTION 8:LOADING CUSTOM TUNESDownload and install the SCT Device Updater software and Drivers from : /support1.From your e-mail, save your custom tunes (.cef files) to your computer’s Desktop.2. Open the SCT Device Updater software andclick the Load Custom Tune File button.3. Click Browse and locate your custom tuneson your Desktop. Alternatively, click Locate Custom Tunes .4. Highlight the Tune you wish to load. 5. The tune you selected should move to theAvailable Tunes section . 6. Select the listed tune in the Available Tunessection, then click the >> button to move the selected tune to the On Device section. 7.Highlight the tune under the On Device section, then click program. Tunes can onlybe loaded one at a time. Repeat steps 3-7 for each tune, the device can hold up to ten custom tunes.NOTE: To edit the name of the file as it appears on your device, you must highlight the file after transferring the file to the “On Device” section of Updater. Next to “Edit Name”, change the name of the file here. Select “Save”, then “Program”.2.4.3.7.6.SECTION 9:ON–DEVICE DATA LOGGING1.Connect the X4 to the OBDII port.2. From the Main Menu , scroll to Gauges/Datalog and pressthe center button on the X4.3. On initial setup , you will need to select Configurationpress the center button , and select your vehicle from a list of data log files. In the future, you can continue without going through the vehicle selection.4. Once you select your vehicle, default gauges will showup and you can now monitor these gauges.5. The items being monitored can be adjusted by press-ing up or down on the device to highlight and then pressing the center button on the X4 to select which reading you’d like to change. Within this menu, you can change the item you’re monitoring, and the units in which it will be displaying. You can also change the layout of the gauges within this menu.6. To start or stop data logging, press the center buttonon the X4 while monitoring the gauges. 7.While monitoring, press right or left on the device to go to the Gauges/Datalog menu. From this menu, you may start recording, select a data log file with which to log, change the gauge layout, and reset the min/max values on the monitor.NOTE: If you cant display a specific value from the preloaded config files, you can download and build custom config files via our Live Link software. If you are not seeing the value or the PID option you want, you can download and build your own configuration file using the Live Link datalogging software from /support.SECTION 10:ADJUSTABLE OPTIONS EXPLAINEDDIESEL VEHICLE SPECIFIC OPTIONSPerformanceThe most aggressive preloaded diesel tune. Good for everyday use, racing, or economy but not recommended for any type of towing.StreetThe Street tune has less power than Performance with a moderate gain over stock, safe for light towing, under 5K lbs.TowingThis tune should be used when towing any significant load as the shifting is specific for towing.Trans OnlyFor heavy loads, the engine and boost are left stock and only the transmission shift points are tuned.Jake BrakeExhaust brake to increase engine braking while coasting to help lower braking temperatures.Locked at CTKeeps the torque converter locked during deceleration to aid in engine braking.Lock In 1-2-3Locks the torque converter in 1st , 2nd and 3rd gear.Agg. Tow HaulMore aggressive shift schedule keeping the engine in its power band longer.DIESEL & GAS VEHICLE OPTIONS:Axle RatioCorrects shift patters / speedometer for aftermarket axles / parts. (Not available on all vehicles)Tire SizeSets tire size to correct shift patterns/speedometer. (Not available on all vehicles)Idle SpeedSets idle speed in RPM.Traction ControlOn/Off setting disables traction control without using the TCS button.WOT ShiftIncrease or Decrease the WOT shift points of each gear individually by MPH.Shift Pressure% change in transmission pressure during shifts. (+ equals firmer, - equals softer)GAS VEHICLE SPECIFIC OPTIONS:Tune TypePerformance levels vary by the octane you select. High-er octane will provide higher performance increase. 93 octane would be the highest increase.Global SparkAdd or remove timing advance to the entire RPM range.Spark by RPMAdd or remove timing by RPM range. (0-2000) (2000-4000) (4000-8000)WOT FuelAdd or remove fuel at wide open throttle. (WOT)Fuel InjectorsAllows you to adjust for different sized injectors. (Not available on all vehicles)CMCV DeletesUpdates tune to handle the CMCV/IMRC delete plates modification.Fan ControlLowers the temperature at which the fan turns on.Rev Limiter DriveSets rev limit in RPM while in drive.Rev Limiter NeutralSets rev limit in RPM while in neutral.Speed LimitRemove, increase, or decrease the vehicle speed limiter. (AKA Governor)Doc. # 7015-99 v2.0MAIN MENUPROGRAM VEHICLEGAUGES / DATALOG VEHICLE FUNCTIONS VEHICLE INFO DEVICE INFO DEVICE SETTINGSBOOST IN PSI11.00MIN: 10.03MAX: 12.06PSICONTROL MODULE VOLTAGE13.00MIN: 11.00MAX: 13.00VCONFIGURATIONFORD DIESEL 6.4L FORD DIESEL 6.7L FORD DIESEL 6.0L & 7.3L FORD GAS ‘07 & PRIOR YEARS FORD GAS ‘08 & NEWER FORD NON-US ’11 & PRIOREXITCONTINUESECTION 11:FREQUENTL Y ASKED QUESTIONSQ: When I try to update my tuner, it says “Please connect SCT device” but it’s already plugged in.A: This is an issue with your PC’s driver software. See our knowledge base at: /support for help. Q: When I connect the tuner to the vehicle, it doesn’t power on.A: Check for blown fuses specific to the OBDII port for your vehicle.Q: Does the tuner have to stay plugged in to keep the vehicle tuned?A: No, after tuning the vehicle you can disconnect the programmer and store it.Q: Can I stack/combine the X4 with another chip or tuning module?A: All chips/tuning products must be removed prior to tuning with any SCT device.Q: Can I tune more than one vehicle with this programmer?A: Yes, but only one vehicle may be tuned at a time and you MUST return the vehicle to the stock to before tuning another vehicle.Q: Can the vehicle be tuned while the engine is running?A: We do not recommend tuning the vehicle while the engine is running as this can cause severe damage to the vehicle and the PCM.Q: Should I return to stock before taking my car to the dealer?A: We recommend that you always return your vehicle to stock before returning to the dealership as this prevents the tuner from becoming locked if the dealer updates the PCM.Q: My device is telling me my car is a Shelby GT500 when I go to program vehicle or My device says Demo Mode when I read Device Info.A: Check device settings and look for Demo Mode. If it is on disable it by turning it to off. This will cause the device to stop identifying your vehicle as a Shelby GT500 and will now operate as needed.Q: My vehicle is modified and I loaded a preloaded tune. Now it won’t run as expected.A: In most cases a modified vehicle requires a custom tune. There are set ups in the preloaded tune options to adapt to certain cold air intakes, however this isper vehicle and what works for one vehicle may not work on another. Please contact a SCT Custom Tune Dealer for a custom tune if your vehicle is heavily modified.Q: I keep getting error code 110AF/110AE. The device tells me to update my device, but it is already up to date.A: You need to read vehicle info and write down your ECU Strategy/ECM OS Part Number. After you’ve read vehicle info you need to go to your computer and update the device using SCT Device Updater to download the additional files needed to tune your vehicle.Q. what is the difference between an unlock and a reset?A. An Unlock is required when a device is “Locked/Married” to a vehicle that is no longer available. A Reset is needed when you have exceeded the “5 unlocks” on the device. Please call SCT Tech Support to have your device Unlocked / Reset.Q: I brought my vehicle to get work done at a dealership and they flashed the vehicle now the device is telling me it is the incorrect vehicle.A: See our knowledge base at: /support for help.NOTE: Devices have five unlocks. An unlock is used when the device is transferred from one vehicle to another.NOTE: Adjustable Options vary for each vehicle and are not available on all vehicles.。

X4简体中文用户指南欢迎使用包装内容 2充电/电池状态 3配对 5找到舒适佩戴搭配 7选择您的设置 7耳挂式佩戴 8耳塞式佩戴 11详细说明按钮功能 14 Jaybird 应用程序 17多点功能 - 连接多设备 18智能手表 19疑难解答 20规格参数 21质保、警告和安全性 22欢迎使用安装或使用产品之前，请参阅安全警告以获取重要的产品安全信息。

JAYBIRD X4坚固，多功能自在奔跑获取详细视频说明，请访问 /support/约8小时播放时间防汗防水 (IPX7)运动贴合 - 稳固舒适10 分钟充电 ≈ 1 小时播放时间快调线夹出色音质，可个性化定制你的运动音效音乐 & 通话集成 USB 充电托架便携袋硅胶耳套（尺寸 1 / 2 / 3）包装内容充电/电池状态我们建议使用 5V 500mA 的 USB 电源为耳机充电。

供电电压超过 5.5 伏特的墙面/车载适配器/充电器会损坏您的 Jaybird 耳机，请勿使用。

2 小时充电可获得 约8 小时播放时间。

10 分钟充电可获得 约1 小时播放时间。

充电/电池状态每次开启耳机时，您都可以听到电池电量提示。

电池电量提示会将剩余电量值四舍五入至最接近的 20％。

手机和 Jaybird 应用程序同样可以显示电池电量。

Jaybird 应用程序能以 1% 的精度显示电池电量。

配对配对，请按住中央按钮直至 LED耳机关闭后，请重复上述 X4找到舒适佩戴搭配1. 安装耳翼找到舒适佩戴搭配2. 找到合适尺寸的耳套和耳翼找到舒适佩戴搭配3. 快调线夹快调线夹可使耳机线不触碰颈部和肩部，尤其适合于耳挂式佩戴。

找到舒适佩戴搭配1. 找到合适尺寸的耳套和耳翼找到舒适佩戴搭配2.衬衫夹可使用衬衫夹将 X4耳机固定到衬衫后领口处。

详细说明按钮功能开/关开启耳机：按住中央按钮直至听到音调上升的“电源开启”声音提示并且 LED 闪烁绿色。

关闭耳机：按住中央按钮直至听到音调下降的“电源关闭”声音提示并且 LED 在关机前亮起红色。