DIN 16901 - Tolerance of plastic parts english

德国标准和国际标准、中国标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉slotted round head wood screws GB999 DIN97 开槽沉头木螺钉slotted countersunk head wood screws GB10010 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404 开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for wood constructions ISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉slotted knurled thumb screws with collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母T-slot nuts ISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes in one face GB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓cup head nib bolts74 DIN608 沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头wire rope clips85 DIN787 T型槽螺钉T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D）studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88100 DIN923 开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screws ISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screws ISO 2010 GB69-85 119 DIN965 十字槽沉头螺钉cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk head screws ISO7047 GB820-85121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2 140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3144 DIN1477 沉头槽销grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washers assemblies GB9074.18-.23 171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head 172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical heads ISO8738194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO 7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameter appro.3d ISO7093 GB96-85208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。

德国标准和国际标准、中国标准中英文对照表发布日期：2007-03-14 浏览次数：829德国标准和国际标准、中国标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard 1DIN1圆锥销taper pins ISO2339GB117 2DIN7圆柱销parallel pins ISO2338GB119-86 3DIN84开槽圆柱头螺钉slotted cheese head screws ISO1207GB65-85 4DIN85开槽盘头螺钉slotted pan head screws ISO1580GB67-85 5DIN93单耳止动垫圈tab washers GB854 6DIN94开口销split cotter pins ISO1234GB91 7DIN95开槽半沉头木螺钉slotted raised csk head wood screws GB101 8DIN96开槽半圆头木螺钉slotted round head wood screws GB99 9DIN97开槽沉头木螺钉slotted countersunk head wood screws GB100 10DIN125-A平垫plain washers ISO7089GB97.1-85 11DIN125-B平垫(带倒角)mediun washers ISO7090GB97.2-85 12DIN126平垫plain washers ISO709113DIN127-A重型弹垫spring lock washers,tang ends GB7244 14DIN127-B标准弹垫spring lock washers,square ends GB93-87 15DIN128-A鞍形弹垫single coil spring lock washers GB7245-87 16DIN137-A弹簧止动垫圈curved spring washers17DIN137-B波形弹垫wave spring washers GB955 18DIN186T型方颈螺栓T-head bolts with square neck GB37-88 19DIN188T型双接头螺栓T-head bolts with double nip20DIN258螺纹圆锥销taper pins with threaded end ISO873721DIN261T型头螺栓T-head bolts22DIN315AF蝶型螺母(美制)wing nuts amercia form23DIN315DF蝶型螺母(德制)wing nuts germany form GB62-88 24DIN316AF蝶型螺钉(美制)wing screws amercia form25DIN317DF蝶型螺钉(德制)wing screws germany form26DIN319圆球型盖型螺母ball knobs27DIN404开槽带孔球面圆柱头螺钉slotted capstan screws GB832-88 28DIN417开槽长圆柱端紧定螺钉slotted set srews with full dog point ISO7435GB75-85 29DIN427开槽平端紧定螺钉(半牙)slotted set srews with chamfered end ISO2342GB73-85 30DIN431小六角特薄细牙螺母pipe nuts with thread GB808-88 31DIN432外舌止动垫圈external tap GB856-88 32DIN433小垫圈(用于圆柱头螺钉)washers for cheese head screws ISO7092GB848-95 33DIN434方斜垫圈(U型)square taper washers for U-section GB852-88 34DIN435方斜垫圈(I型)square taper washers for I-sections GB852-88 35DIN436方垫圈square washers36DIN438开槽凹端紧定螺钉slotted set with cup point ISO7436GB74-85 37DIN439六角薄螺母hexagon thin nuts ISO4035GB6172-86 38DIN439细牙六角薄螺母hexagon thin nuts ISO8675GB6173-86 39DIN440木螺钉专用垫圈rounds washers for wood constructions ISO709440DIN443密封帽sealing caps,push-in type41DIN444活节螺栓B 型eye bolts form B GB798-88 42DIN462内舌止动垫圈internal tab washers43DIN463双耳止动垫圈washers with two taps GB855-88 44DIN464滚花高头螺钉knurled thumb screws with collar GB834-88 45DIN465开槽滚花高头螺钉slotted knurled thumb screws with collar46DIN466滚花高螺母knurled thumb nuts with collar GB806-88 47DIN467滚花薄螺母knurled thumb thin nuts GB807-88 48DIN470锁紧垫圈sealing washers49DIN471轴用弹性挡圈retaining rings for shafts(external),circlips GB894.1-86 50DIN472孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-86 51DIN478方头带垫螺栓square head bolts with collar52DIN479方头圆柱底端螺栓square head bolts with half dog point53DIN480方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54DIN508T型槽螺母T-slot nuts ISO29955DIN525单头螺柱single end studs56DIN529地脚螺栓masonry bolts GB799-88 57DIN546带槽圆螺母slotted round nuts GB817-7658DIN547端面带孔圆螺母round nuts with drilled holes in one face GB815-88 59DIN551开槽平端紧定螺钉slotted sit screws with flat point ISO4776GB73-85 60DIN553开槽锥端紧定螺钉slotted set screws with cone point ISO7434GB71-85 61DIN555六角螺母hexagon nuts ISO403462DIN557方螺母-C square nuts GB39-88 63DIN558六角头螺钉hexagon screws ISO401864DIN561六角头圆柱端紧定螺钉hexagon set screws with full dog point65DIN562薄型方螺母-B square nuts without bevel(pressed nuts)66DIN571六角头木螺钉hexagon head wood screws (coach screws)GB102-86 67DIN580吊环螺钉lifting eye bolts ISO3266GB825-76 68DIN582吊环螺母lifting eye nuts69DIN601六角头螺栓hexagon bolts ISO401670DIN603大半圆头方颈螺栓(马车螺栓)mushroom head square neck bolts (carriagebolts)ISO8677GB14-8871DIN604沉头带插销马车螺栓flat countersunk nib bolts72DIN605沉头长方颈马车螺栓flat countersunk long square neck bolts73DIN607半圆头带插销马车螺栓cup head nib bolts74DIN608沉头短方颈马车螺栓flat countersunk short square neck bolts75DIN609六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76DIN610六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77DIN653滚花平头螺钉knurled thumb screws thin type GB835-88 78DIN660半圆头铆钉round head rivets ISO1051GB867-86 79DIN661沉头铆钉contersunk head rivets ISO1051GB869-86 80DIN662半沉头铆钉raised contersunk head rivets ISO105181DIN674大扁头铆钉mushroom head rivets ISO105182DIN703重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83DIN705侧面带孔圆螺母adjusting rings,light range (shafting collars)GB816-88 84DIN741卡头wire rope clips85DIN787T型槽螺钉T-slot screws ISO29986DIN835双头螺柱（牙长=2D）studs-metal (end=2d)GB900-88 87DIN906内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88DIN908内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89DIN909外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90DIN910外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91DIN911内六角扳手socket wrenches ISO293692DIN912内六角圆柱头螺钉hexagon socket cap screws ISO4762GB70-8593DIN913内六角平端紧定螺钉hexagon socket set screws with flat point ISO4026GB77-8594DIN914内六角尖端紧定螺钉hexagon socket set screws with cone point ISO4027GB78-8595DIN915内六角圆柱端紧定螺钉hexagon socket set screws with dog point ISO4028GB79-8596DIN916内六角凹端紧定螺钉hexagon socket set screws with cup point ISO4029GB80-8597DIN917薄型盲螺母hexagon cap nuts98DIN920开槽小圆柱头螺钉slotted short cheese head screws99DIN921开槽大圆柱头螺钉slotted large cheese head screws GB838-88 100DIN923开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88 101DIN927开槽无头轴肩螺钉slotted shoulder screws102DIN928焊接方螺母square weld nuts GB/T13680-92 103DIN929焊接六角螺母hexagon weld nuts GB/T13681-92 104DIN931六角头螺栓（半牙）hexagon head screws ISO4014GB5782-86 105DIN933六角头螺栓（全牙）hexagon head screws ISO4017GB5783-86 106DIN934六角头螺母(1型)hexagon full nuts ISO4032GB6170-86 107DIN934细牙六角头螺母(1型)hexagon full nuts ISO8673GB6171-86 108DIN935开槽六角螺母hexagon slotted and castle nuts ISO7035GB6178-86 109DIN936六角头薄螺母hexagon thin nuts ISO4035GB6172.1-86 110DIN937六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038GB6181-86 111DIN938双头螺距（牙长=1D）studs metal (end=1d)GB897-88 112DIN939双头螺距（牙长=1.25D）studs metal (end=1.25d)GB898-88 113DIN940双头螺距（牙长=1.5D）studs metal (end=1.5d)114DIN960六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765GB5785-86 115DIN961六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676GB5786-86 116DIN962头部穿孔六角头螺栓additional shapes and versions for bolts117DIN963开槽沉头螺钉slotted countersund head screws ISO 2009GB68-85118DIN964开槽半沉头螺钉slotted raised countersunk oval head screws ISO 2010GB69-85119DIN965十字槽沉头螺钉cross recessed countersunk head screws ISO7046GB819-85 120DIN966十字槽半沉头螺钉cross recessed raised countersunk head screws ISO7047GB820-85121DIN970六角头螺母hexagon nuts type-1122DIN971六角头螺母hexagon nuts type-2123DIN972细牙六角头螺母(2型)hexagon nuts with fine thread ISO8674GB6176-86 124DIN975牙条(全螺纹)threaded rods(studdings)GB15389-94 125DIN976螺纹销threaded pins(stud bolts)126DIN979六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127DIN980全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metallnutsISO7199GB6184-86128DIN981圆螺母locknuts ISO2982GB812-88129DIN982六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type,with nylon insertISO7040GB889.1-86130DIN985六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type,with nylon insertISO10511GB6172.2-86131DIN986六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132DIN988配合垫片shim rings133DIN1052木材连接用垫片washers for timber connectors134DIN1151沉头钢钉round plain head nails135DIN1440销钉专用垫片A型plain washers for clevis pins(A型)ISO8738136DIN1441销钉专用垫片plain washers for clevis pins137DIN1444带头销钉clevis pins with head ISO2341138DIN1471圆锥型槽销grooved pins,taper grooved ISO8744GB/T13829.2 139DIN1472圆锥型槽销(半槽)grooved pins,taper grooved half length ISO8745GB/T13829.2 140DIN1473平行槽销(带倒角)grooved pins,parallel grooved full length ISO8740141DIN1474前端凹槽槽销grooved pins,reserve grooved half length ISO8741142DIN1475中部凹槽槽销grooved pins,centre grooved ISO8742143DIN1476圆头槽销grooved pins with round head ISO8746GB/T13829.3 144DIN1477沉头槽销grooved pins with countersunk head ISO8747145DIN1479六角螺母棒turnuckles(centre parts),made out of hexagon bar146DIN1480花篮螺栓turnuckles with eye bolt and hook bolt147DIN1481弹性圆柱销spring pins,heavy type ISO8752GB879-86 148DIN1587组合式盖型螺母hexagon domed cap nuts GB802-88 149DIN1804开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150DIN1816圆螺母（带插销孔）round nuts with set holes151DIN2093盘型弹簧垫圈disc springs152DIN3017喉箍hose clamps153DIN3404润滑油嘴（旋扭头）lubricating nipples,button head154DIN3567管夹shackles for conduilts155DIN3570U型螺栓stirrup bolts(U-bolts)156DIN6319球面垫圈spherical washers,conical seats GB849-88157DIN6325圆柱销parallel pins ISO8734158DIN6330厚六角螺母hexagon nuts ,1.5d GB56-88159DIN6331厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86 160DIN6334长六角螺母hexagon nuts ,3d161DIN6797-A外齿锁紧垫圈external teeth lock washers GB862.1-87 162DIN6797-I内齿锁紧垫圈internal teeth lock washers GB861.1-87 163DIN6798-A外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87 164DIN6798-I内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87 165DIN6799开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166DIN6885平键（A型）parallel keys(form A )ISO773/2491167DIN6888半圆键woodruff keys ISO3912168DIN6899嵌环（支撑环）thimbles169DIN6900机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17 170DIN6901自攻螺钉和垫圈组合件tapping screws and washers assemblies GB9074.18-.23171DIN6912薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head172DIN6914大六角头螺栓hexagon head bolts with large head(friction grip bolts)173DIN6915大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174DIN6916大垫圈round washers for friction grip bolts175DIN6917楔型方垫圈spuare taper washers for friction grip bolts on T-sections176DIN6923六角法兰面螺母hexagon flange nuts ISO4161GB6177-86177DIN6925全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallicnutsISO7042GB6185.1-2000178DIN7337开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179DIN7338扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86 180DIN7343螺旋夹紧销spiral pins ISO8750181DIN7346轻型弹性圆柱销spring pins,light type ISO13337182DIN7349重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183DIN7500ISO公制螺纹螺钉(多种头型)threadforming screws for ISO-metric thread184DIN7504自攻自钻螺钉(多种头型)self-drilling tapping screws185DIN7513开槽切削螺纹螺钉(多种头型)thread cutting screws186DIN7516十字槽切削螺纹螺钉(多种头型)thread cutting screws cross recess187DIN7965T型四爪螺母tee nuts with pronge188DIN7968钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structures GB1228/1229/1230 189DIN7971开槽盘头自攻螺钉pan head tapping screws with slot ISO1481GB5282-85190DIN7972开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482GB5283-85191DIN7973开槽半沉头自攻螺钉raised countersunk oval head tapping screws withslotISO1483GB5284-85192DIN7976六角头自攻螺钉hexagon tapping screws ISO1479GB5285-85193DIN7980圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindricalheadsISO8738194DIN7981十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO 7049GB845-85195DIN7982十字槽沉头自攻螺钉countersunk flat head tapping screws with crossrecessedISO7050GB846-85196DIN7983十字槽半沉头自攻螺钉raised countersunk oval head tapping screws withcross recessedISO7051GB847-86197DIN7984薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198DIN7985十字槽盘头螺钉pan head screws with cross recessed ISO7045GB818-85199DIN7989钢结构用垫圈washers for steel structures GB1230-84 200DIN7990钢结构用六角头螺栓hexagon head bolts for steel structures GB1229-84 201DIN7991内六角沉头螺钉hexagon socket countersunk head screws ISO10642GB/T70.3-2000 202DIN7993轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203DIN7995十字槽半沉头木螺钉cross recessed raised countersunk head woodscrewsGB952-86204DIN7996十字槽圆头木螺钉cross recessed round head wood screws GB950-86205DIN7997十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86 206DIN8140螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207DIN9021大外径垫圈washers,outside diameter appro.3d ISO7093GB96-85 208DIN11024弹簧卡子spring cotter for a bolt209DIN13257平板螺栓belting bolts (elevator bolts)210DIN18182干壁钉（墙板钉）dry wall screws211DIN28129环型螺母lifting nuts(eye nuts)GB63-88 212DIN70952圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。

德标和国标,国际标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉slotted round head wood screws GB999 DIN97 开槽沉头木螺钉slotted countersunk head wood screws GB10010 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404 开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for wood constructions ISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉slotted knurled thumb screws with collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母T-slot nuts ISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes in one face GB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓cup head nib bolts74 DIN608 沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头wire rope clips85 DIN787 T型槽螺钉T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D）studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88100 DIN923 开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screws ISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screws ISO 2010 GB69-85119 DIN965 十字槽沉头螺钉cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk head screws ISO7047 GB820-85 121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3144 DIN1477 沉头槽销grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washers assemblies GB9074.18-.23171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nutsISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structuresGB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical heads ISO8738 194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO 7049GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessedISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86 206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameter appro.3d ISO7093 GB96-85208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。

德标、欧标、国际、国标对照表—— DIN EN ISO GB 对照表新德标旧德标 英文名 中文名 国标 DIN EN ISO 4014DIN 931-1 Hexagon head bolts - Product grades A and B(ISO 4014:1999) 六角头螺栓 GB/T 5782-2000 DIN EN ISO 4016DIN 601 Hexagon head bolts - Product grade C(ISO 4016:1999) 六角头螺栓 C 级 GB/T 5780-2000 DIN EN ISO 4017DIN 933 Hexagon head screws - Product grade A and B (ISO 4017:1999) 六角头螺栓 全螺纹 GB/T 5783-2000 DIN EN ISO 4018DIN 558 Hexagon head screws - Product grade C (ISO 4018:1999) 六角头螺栓 全螺纹 C 级 GB/T 5781-2000 DIN EN ISO 8676DIN 961 Hexagon head screws with metric fine pitch thread - Product grade A and B(ISO 8676:1999) 六角头螺栓 细牙 全螺纹 GB/T 5786-2000 DIN EN ISO 8765DIN 960 Hexagon head bolts with fine pitch thread - Product grades A and B(ISO 8765:1999) 六角头螺栓 细牙 GB/T 5785-2000 DIN EN ISO 4032DIN 934 Hexagon nuts,style 1-Product grades A and B(ISO: 4032:1999) 1型六角螺母 GB/T 6170-2000 DIN EN ISO 4033Hexagon nuts,style 2-Product grades A and B(ISO: 4033:1999) 2型六角螺母 GB/T 6175-2000 DIN EN ISO 4034DIN 555 Hexagon nuts - Product grade C (ISO 4034:1999) 六角螺母 C 级 GB/T 41-2000 DIN EN ISO 4035DIN 439-2 Hexagon thin nuts(chamfered)-Product grade A and B (ISO 4035:1999) 六角薄螺母 GB/T 6172.1-2000 DIN EN ISO 4036DIN 439-1 Hexagon thin nuts - Product grade B(unchamfered)(ISO 4036:1999) 六角薄螺母 无倒角 GB/T 6174-2000 DIN EN ISO 8673DIN 934| DIN 971-1 Hexagon nuts,style 1,with metric fine pitch thread - Product grades A and B (ISO 8673:1999) 1型六角螺母 细牙 GB/T 6171-2000 DIN EN ISO 8674DIN 971-2 Hexagon nuts,style 2,with metric fine pitch thread - Product grades A and B (ISO 8674:1999) 2型六角螺母 细牙 GB/T 6176-2000 DIN EN ISO 8675DIN 439-2 Hexagon thin nuts with metric fine pitch thread - Product grades A and B (ISO 8675:1999) 六角薄螺母 细牙 GB/T 6173-2000 DIN EN ISO 4762 DIN 912 Hexagon socket head cap screws(ISO 4762:1997) 内六角圆柱头螺钉GB/T 70.1-2000DIN EN ISO 7380Hexagon socket button head sxrews (ISO 7380:1997) 内六角平圆头螺钉 GB/T 70.2-2000 DIN EN ISO 10642DIN 7991 Hexagon socket countersunk head screws (ISO 10642:1997) 内六角沉头螺钉 GB/T 70.3-2000 DIN EN ISO 1207DIN 84 Slotted cheese head screws-Product grade A(ISO 1207:1992) 开槽圆柱头螺钉 GB/T 65-2000 DIN EN ISO 1580DIN 85 Slotted pan head screws-Product grade A(ISO 1580:1994) 开槽盘头螺钉 GB/T 67-2000 DIN EN ISO 2009DIN 963 Slotted countersunk flat head screws(common head style)(ISO 2009:1994) 开槽沉头螺钉 GB/T 68-2000 DIN EN ISO 2010DIN 964 Countersunk slotted raised head screws(common head style)-Produce grade A(ISO 2010:1994) 开槽半沉头螺钉 GB/T 69-2000 DIN EN ISO 7045DIN 7985 Pan head screws with type H or type Z cross recess-Product grade A(ISO 7054:1994) 十字槽盘头螺钉 GB/T 818-2000 DIN EN ISO 7046-1DIN 965 Countersunk flat head screws (common head style)with type H or type Z cross recess,product grade A-Part 1:Steel of property class 4.8(ISO 7046-1:1994) 十字槽盘头螺钉 第1部分：钢4.8级 GB/T 819.1-2000 DIN EN ISO 7046-2DIN 965 Cross recessed countersunk flat head screws (common head style),product grade A-Part2:Steel of property class 8.8,stainless steel and nonferous metals(ISO 7046-2:1990) 十字槽沉头螺钉 第2部分：钢8.8、不锈钢A2-70和有色金属CU2或CU3 GB/T 819.2-1997 DIN EN ISO 7047DIN 966 Countersunk raised head screws (common head style) with type H or type Z cross recess-Product grade A(ISO 7047:1994) 十字槽半沉头螺钉 GB/T 820-2000 DIN EN ISO 7048Cross recessed cheese head screws (ISO 7048:1998) 十字槽圆柱头螺钉 GB/T 822-2000 DIN EN ISO 10644Screw and washer assemblies with plain washers-Washer hardness classes 200HV and 300HV(ISO 10644:1998) 螺栓或螺钉和平垫圈组合件 GB/T 9074.1-2002 DIN EN ISO 10510Tapping screw and washer assemblies with plain washers(ISO 10510l:1999) 自攻螺钉和平垫圈组合件 GB/T 9074.18-2002 IDN EN ISO 15480Hexagon washer head drilling screws with tapping screws thread (ISO 15480:1999) 六角凸缘自钻自攻螺钉 GB/T 15856.5-2002 IDN EN ISO 15481Cross recessed pan head drilling screws with tapping screw thread(ISO 15481:1999) 十字槽盘头自钻自攻螺钉 GB/T 15856.1-2002 IDN EN ISO 15482 Cross recessed countersunk head drilling screws with tapping screw thread (ISO 15482:1999) 十字槽沉头自钻自攻螺钉GB/T 15856.2-2002IDN EN ISO 15483Cross recessed raised countersunk head drilling screws with tapping screw thread(ISO 15483:1999) 十字槽半沉头自钻自攻螺钉 GB/T 15856.3-2002 DIN EN ISO 10669Plain washers for tapping screw and washer assemblies - Normal and large series - Product grade A （ISO 10669:1999) 平垫圈 用于自攻螺钉和垫圈组合件 GB/T 97.5-2002 DIN EN ISO 10673Plain washers for screw and washer assemblies - Small,normal and large series - Product grade A (ISO 10673:1998) 平垫圈 用于螺钉和垫圈组合件 GB/T 97.4-2002 DIN EN ISO 2338DIN 7 Parallel pins,of unhardened steel and austenitic stainless steel(ISO 2338:1997) 圆柱销 不淬硬钢和奥氏体不锈钢 GB/T 119.1-2000 DIN EN ISO 8733DIN 7979 Parallel pins whit internal thread,of unhardened steel and austenitic stainless steel(ISO 8733:1997) 内螺纹圆柱销 不淬硬钢和奥氏体不锈钢 GB/T 120.1-2000 DIN EN ISO 8734DIN 6325 Parallel pins,of hardened steel or martensitic stainless steel(Dowel pins)(ISO 8734:1997) 圆柱销 淬硬钢和马氏体不锈钢 GB/T 119.2-2000 DIN EN ISO 8735DIN 7979 Parallel pins with internal thread,of hardened steel and martensitic stainless steel(ISO 8735:1997) 内螺纹圆柱销 淬硬钢和马氏体不锈钢 GB/T 120.2-2000 DIN EN ISO 8748DIN 7344 Spring-type straight pins,coiled,heavy duty (ISO 8748:1997) 弹性圆柱销 卷制 重型 GB/T 879.3-2000 DIN EN ISO 8750DIN 7343 Spring-type straight pins,coiled,standard duty (ISO 8750:1997) 弹性圆柱销 卷制 标准型 GB/T 879.4-2000 DIN EN ISO 8751Spring-type straight pins,coiled,light duty （ISO 8751:1997) 弹性圆柱销 卷制 轻型 GB/T 879.5-2000 DIN EN ISO 8752DIN 1481 Spring-type straight pins,slotted,heavy duty (ISO 8752:1997) 弹性圆柱销 直槽 重型 GB/T 879.1-2000 DIN EN ISO 13337DIN 7346 Spring-type straight pins,slotted,light duty (ISO 13337:1997) 弹性圆柱销 直槽 轻型 GB/T 879.2-2000 DIN EN ISO 1234DIN 94 Split pins （ISO1234:1997) 开口销 GB/T 91-2000 DIN EN ISO 7089Plain washers-Normal series-Product grade A 平垫圈 A 级 GB/T 97.1-2002 DIN EN ISO 7090Plain washers,chamfered-Normal series-Product grade A(ISO 7090:2000) 平垫圈 倒角型 A 级 GB/T 97.2-2002 DIN EN ISO 7091Plain washers-Normal series-Product grade C(ISO 7091:2000) 平垫圈 C 级 GB/T 95-2002 DIN EN ISO 7092 Plain washers-Small series-Product grade A(ISO 7092:2000)小垫圈 A 级 GB/T 848-2002DIN EN ISO 7093-1 Plain washers-Large series-Part 1: Product grade A(ISO 70931-1:2000)大垫圈 A 级 GB/T 96.1-2002DIN EN ISO 7093-2Plain washers-Normal series-Part 3: Product grade C(ISO 70936-2:2000) 大垫圈 C 级 GB/T 96.2-2002 DIN EN ISO 7094Plain washers-Extra large series -Product grade C(ISO 7094:2000) 特大垫圈 C 级 GB/T 5287-2002 DIN EN ISO 7040DIN 982| DIN 6924 Prevailing torque type hexagon nuts (with non-metallic insert),style 1 - Property classes 5,8 and 10(ISO 7040:1997) 1型非金属嵌件六角锁紧螺母 GB/T 889.1-2000 DIN EN ISO 7042DIN 980| DIN 6925 Prevailing torque type all-metal hexagon nuts,style 2 - Property classes 5,8, 10 and 12(ISO 7042:1997) 2型全金属六角锁紧螺母 GB/T 6185.1-2000 DIN EN ISO 7719Prevailing torque type all-metal hexagon nuts,style 1- Property classes 5,8 and 10(ISO 7719:1997) 1型全金属六角锁紧螺母 GB/T 6184-2000 DIN EN ISO 10511DIN 985 Prevailing torque type hexagon thin nuts (with non-metallic insert )(ISO 10511:1997) 非金属嵌件六角锁紧薄螺母 GB/T 6072.2-2000 DIN EN ISO 10512DIN 982| DIN 6924 Prevailing torque type hexagon nuts (with non-metallic insert),style 1,with metric fine pitch thread-Property classes 6,8 and 10(ISO 10512:1997) 1型非金属嵌件六角锁紧螺母 细牙 GB/T 889.2-2000 DIN EN ISO 10513 DIN 980|DIN 6925 Prevailing torque type all-metal hexagon nuts,style 2,with metric fine pitch thread - Property classes 8,10 and 12(ISO 10513:1997)2型全金属六角锁紧螺母 细牙GB/T 6185.2-2000。

紧固件DIN ISO GB标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in EnglishISO-Standard GB-Standard1 DIN1 圆锥销 taper pins ISO2339 GB1172 DIN7 圆柱销 parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉 slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉 slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈 tab washers GB8546 DIN94 开口销 split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉 slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉 slotted round head wood screws GB999 DIN97 开槽沉头木螺钉 slotted countersunk head wood screws GB10010 DIN125-A 平垫 plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫 plain washers ISO709113 DIN127-A 重型弹垫 spring lock washers,tang ends GB724414 DIN127-B 标准弹垫 spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫 single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈 curved spring washers17 DIN137-B 波形弹垫 wave spring washers GB95518 DIN186 T型方颈螺栓 T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓 T-head bolts with double nip20 DIN258 螺纹圆锥销 taper pins with threaded end ISO873721 DIN261 T型头螺栓 T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母 ball knobs27 DIN404 开槽带孔球面圆柱头螺钉 slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉 slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母 pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈 external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈 square washers36 DIN438 开槽凹端紧定螺钉 slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母 hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母 hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈 rounds washers for wood constructions ISO709440 DIN443 密封帽 sealing caps,push-in type41 DIN444 活节螺栓B 型 eye bolts form B GB798-8842 DIN462 内舌止动垫圈 internal tab washers43 DIN463 双耳止动垫圈 washers with two taps GB855-8844 DIN464 滚花高头螺钉 knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉 slotted knurled thumb screws with collar46 DIN466 滚花高螺母 knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母 knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈 sealing washers49 DIN471 轴用弹性挡圈 retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈 retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓 square head bolts with collar52 DIN479 方头圆柱底端螺栓 square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓 square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母 T-slot nuts ISO29955 DIN525 单头螺柱 single end studs56 DIN529 地脚螺栓 masonry bolts GB799-8857 DIN546 带槽圆螺母 slotted round nuts GB817-7658 DIN547 端面带孔圆螺母 round nuts with drilled holes in one faceGB815-8859 DIN551 开槽平端紧定螺钉 slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉 slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母 hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉 hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉 hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉 hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉 lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母 lifting eye nuts69 DIN601 六角头螺栓 hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓 flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓 flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓 cup head nib bolts74 DIN608 沉头短方颈马车螺栓 flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹） hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹） hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉 knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉 round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉 contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉 raised contersunk head rivets ISO105181 DIN674 大扁头铆钉 mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母 adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母 adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头 wire rope clips85 DIN787 T型槽螺钉 T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D） studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉 hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉 hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉 hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉 hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手 socket wrenches ISO293692 DIN912 内六角圆柱头螺钉 hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉 hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉 hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉 hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉 hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母 hexagon cap nuts98 DIN920 开槽小圆柱头螺钉 slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉 slotted large cheese head screws GB838-88 100 DIN923 开槽圆柱头轴肩螺钉 slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉 slotted shoulder screws102 DIN928 焊接方螺母 square weld nuts GB/T13680-92103 DIN929 焊接六角螺母 hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙） hexagon head screws ISO4014 GB5782-86 105 DIN933 六角头螺栓（全牙） hexagon head screws ISO4017 GB5783-86 106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86 108 DIN935 开槽六角螺母 hexagon slotted and castle nuts ISO7035GB6178-86109 DIN936 六角头薄螺母 hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母 hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D） studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D） studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D） studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙） hexagon head bolts,metric fine pitch thread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙） hexagon head bolts,metric fine pitch thread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓 additional shapes and versions for bolts 117 DIN963 开槽沉头螺钉 slotted countersund head screws ISO 2009 GB68-85 118 DIN964 开槽半沉头螺钉 slotted raised countersunk oval head screws ISO 2010 GB69-85119 DIN965 十字槽沉头螺钉 cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉 cross recessed raised countersunk head screws ISO7047 GB820-85121 DIN970 六角头螺母 hexagon nuts type-1122 DIN971 六角头螺母 hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销 threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型） hexagon thin slotted and castle nuts 127 DIN980 全金属六角锁紧螺母（1型） prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母 locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母 prevailling torque type hexagonnuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母 prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母 prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片 shim rings133 DIN1052 木材连接用垫片 washers for timber connectors134 DIN1151 沉头钢钉 round plain head nails135 DIN1440 销钉专用垫片A型 plain washers for clevis pins(A型) ISO8738 136 DIN1441 销钉专用垫片 plain washers for clevis pins137 DIN1444 带头销钉 clevis pins with head ISO2341138 DIN1471 圆锥型槽销 grooved pins,taper grooved ISO8744 GB/T13829.2 139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full lengthISO8740141 DIN1474 前端凹槽槽销 grooved pins,reserve grooved half lengthISO8741142 DIN1475 中部凹槽槽销 grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销 grooved pins with round head ISO8746 GB/T13829.3 144 DIN1477 沉头槽销 grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒 turnuckles(centre parts),made out of hexagon bar 146 DIN1480 花篮螺栓 turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销 spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母 hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手） slotted round nuts for hook spanner 150 DIN1816 圆螺母（带插销孔） round nuts with set holes151 DIN2093 盘型弹簧垫圈 disc springs152 DIN3017 喉箍 hose clamps153 DIN3404 润滑油嘴（旋扭头） lubricating nipples,button head154 DIN3567 管夹 shackles for conduilts155 DIN3570 U型螺栓 stirrup bolts(U-bolts)156 DIN6319 球面垫圈 spherical washers,conical seats GB849-88157 DIN6325 圆柱销 parallel pins ISO8734158 DIN6330 厚六角螺母 hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母 hexagon nuts ,1.5d with collar GB6177-86 160 DIN6334 长六角螺母 hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈 external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈 internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈 external teeth serrated lock washersGB862.2-87164 DIN6798-I 内锯齿锁紧垫圈 internal teeth serrated lock washersGB861.2-87165 DIN6799 开口挡圈 retaining rings for shafts(E-rings),circlipsGB896-76166 DIN6885 平键（A型） parallel keys(form A ) ISO773/2491167 DIN6888 半圆键 woodruff keys ISO3912168 DIN6899 嵌环（支撑环） thimbles169 DIN6900 机器螺钉和垫圈组合件 screws and washers assembliesGB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件 tapping screws and washers assemblies GB9074.18-.23171 DIN6912 薄型带孔内六角圆柱头螺钉 hexagon socket head cap screws with hole,low head172 DIN6914 大六角头螺栓 hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母 hexagon nuts with large wideth acrossflat(friction grip nuts)174 DIN6916 大垫圈 round washers for friction grip bolts175 DIN6917 楔型方垫圈 spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母 hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型） prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头） blind rivets GB12617/12618 179 DIN7338 扁平头半空心/全空心铆钉 rivets for brake and clutch lining GB875/975-86180 DIN7343 螺旋夹紧销 spiral pins ISO8750181 DIN7346 轻型弹性圆柱销 spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈 washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws forISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母 tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副 hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉 pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉 countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉 raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉 hexagon tapping screws ISO1479 GB5285-85 193 DIN7980 圆柱头螺钉用弹簧垫圈 spring lock washers for screws with cylindrical heads ISO8738194 DIN7981 十字槽盘头自攻螺钉 pan head tapping screws with cross recessed ISO 7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉 countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉 raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉 hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉 pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈 washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓 hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉 hexagon socket countersunk head screwsISO10642202 DIN7993 轴用钢丝挡圈 roundwire snap rings for shafts GB895.2-86 203 DIN7995 十字槽半沉头木螺钉 cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉 cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉 cross recessed countersunk head wood screws GB951-86206 DIN8140 螺纹护套（普通\自锁等） ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈 washers,outside diameter appro.3d ISO7093GB96-85208 DIN11024 弹簧卡子 spring cotter for a bolt209 DIN13257 平板螺栓 belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉） dry wall screws211 DIN28129 环型螺母 lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈 tab washers for slotted round nuts GB858-渗碳和渗氮常识钢的渗碳---就是将低碳钢在富碳的介质中加热到高温(一般为900--950C),使活性碳原子渗入钢的表面,以获得高碳的渗层组织。

德标和国标,国际标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉slotted round head wood screws GB999 DIN97 开槽沉头木螺钉slotted countersunk head wood screws GB10010 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404 开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for wood constructions ISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉slotted knurled thumb screws with collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母T-slot nuts ISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes in one face GB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓cup head nib bolts74 DIN608 沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头wire rope clips85 DIN787 T型槽螺钉T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D）studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88100 DIN923 开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screws ISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screws ISO 2010 GB69-85119 DIN965 十字槽沉头螺钉cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk head screws ISO7047 GB820-85 121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3144 DIN1477 沉头槽销grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washers assemblies GB9074.18-.23 171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head 172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structuresGB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical heads ISO8738 194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO 7049GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessedISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86 204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameter appro.3d ISO7093 GB96-85208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。

DIN 1690 Part 2金属材料铸件交付技术规范钢铸件;非破坏性测试严格等级为了与ISO出版的标准相适应,对十进制标识用逗号标示.1.应用领域1.1作为对DIN1690第一部分铸件交付技术规范的补充,本规范主要是将钢铸件内外部条件作个分类(见说明).这个分类是基于非破坏性测试的结果1.2 本规范不适用于焊接结构的产品(定义参考DIN1690第一部分),关于这些,关于见外部条件及其检验的特殊协议应该在下单时说明.2.严格等级2.1严格等级的划分外部条件等级的划分应该以表1或2所列参数的磁性粒子或渗透检验,或附件A或B中的图片为基础.如果有矛盾,表1或2的值是强制性的.内部条件等级的划分由表3或4(见条款3.3.2.1).所列参数的超声波探伤或X探伤检验的结果为基础2.2严格等级的选择2.2.1考虑到以2.1条分类为基础,钢铸件,或产品标准规范或订单上内外部允许值的不一, 2.3条的使用是可以接受的.就这个目的,下面这些因素必须按等级,类型与分类记下2.2.1.1不同的铸件区域可能适用不同的等级,在这种情况下,重要的区域必须清楚的说明了,------指明位置与长度宽度------如果在2.2.3里描述的焊接末端与特殊部位,还需要说明深度.2.2.1.2除了相同的等级值,在内外部条件上也可能出现不同的等级.2.2.1.3等级1只适用于2.2.3里描述的焊接末端与特殊部位.2.2.1.4铸件的形状影响它们的条件与测试性能.除了这些,铸件的测试性能还取决于表面的条件.2.2.2如果在下单时,没有达成严格等级,或没有在产品标准里作描述,可以使用等级5.2.2.3在特殊情况下,如图1(参照”特殊外层”)所示的外区外层的壁厚可能要求更高的(数值上更低的)严格等级.比如由生产商加工的表面(2.3条例3)2.2.4至于焊接件(见DIN1690第一部分的定义)的生产,同样的要求适用于母体,除非在下单时另有约定.2.3标准适用.不同等级要求标准的选用包括下面这些因素.-----“严格等级”的字符.-----本标准的号码-----严格等级中提到的字符S(表面)表示外表面条件(见表1与2)例1:Severity level DIN1690-S2-V4如果哪里与规范3.3.2.1规范里提到的不一样,测试方法的选择权不在生产商.下面的测试编码必须加到严格等级的标识里,如例2与3所示: 磁性粒子检验 M渗透检验 E超声波检验 UX探伤检验 R例2:Severity level DIN1690-MS2-RV4例3:Severity level DIN1690-MS2-RV4.在所有的加工面上:MS1,在表面下20MM的用UV13.测试3.1关于测试协议与产品测试文件.3.1.1如果铸件要求执行严格等级1到3,那么对于库存产品也要求重新测试并保证与相关的要求相一致.3.1.2如果铸件要求执行严格等级4到5,并且买方有要求,那么对于库存产品也要求重新测试并保证与相关的要求相一致.3.1.3除了下单时另有约定,必须签发按DIN50 049里规定的检验证明B,说明库存品的非破坏测试结果.3.2测试计划范围.除了在下单时有约定(比如,系列批产),所有供应的铸件按要求的等级进行正确的测试.3.3测试方法3.3.1磁性粒子检验或渗透检验采用如铁或钢测试表1935里的磁性粒子检验或STAHL-EISEN-PRUFBLATT1936里的渗透测试,以确定钢铸件与表1或2里的外表面条件要求.如果铸件不是用磁性铸钢制成,那么将采用渗透测试,如果用的是磁性铸钢,那么磁性粒子检验将优先采用.除了另有约定(见2.3),磁性粒子检验应该用来检验加工面.附图A的系列图片将作为非直线装配指示磁性粒子检验的辅助. 附图B的系列图片将作为非直线装配指示磁性粒子检验的辅助.每个图片对应于表1中的1到5的严格等级或表2中的01到5的等级.确定严格等级的方法为,在最不利区上放个148毫米X102毫米(A6规格)的框,然后在系列图片中找相同或相类似的最不利的.3.3.2 X探伤检验或超声波检验.3.3.2.1除非下单时另有约定,检验方法由生产商确定.决定时,下列需要考虑.如果是奥氏体材料,只需做X探伤检验.如果是低合金钢(包括珠光体马氏体),作为测定缺陷类型的超声波探伤的一个补充, 必要时,X探伤检验将用来测试薄壁,焊接末端(见表3,11行).作为测定缺陷类型的X探伤的一个补充, 超声波探伤检验将用来测试厚壁铸件以及焊接件,以确定缺陷的深度位置以及厚度(见表4,脚注2).在选择方法时,要考虑到待测缺陷的大小以及铸件的几何形状.基于这个原因,对确定厚与薄作精确的区分将不大可能.它处于50到100毫米.3.3.2.2超声波探伤按STAHL EISEN PRUFBLATT1922进行超声波探伤检验.严格等级在1到4级的,需要达到测试1级,对于严格等级为5的,必须达到目的测试等级2.3.3.2.3 X探伤检验DIN54 109第一二部分,还有DIN 54 111第二部分适用于X探伤检验.除了特定区域有标注外,测试在DIN54 111第二部分测试等级A下进行.DIN54 109第二部分图像等级也必须满足.表1STAHL EISEN PRUFBLATT1935下的磁性粒子检验下的最大允许值(参考面积为105毫米X148毫米,对应于DIN476里的A6)表2 按“ STAHL EISEN PRUFBLATT1936”进行的着色渗透测试的最大允许值(参考面积为105毫米X148毫米,对应于DIN476里的A6)图1 壁分区(壁的分区与可装配铸件的尺寸是相关的) 图2:对表3里”个别区”与”全区”的解释.个别区F是指到邻近区的距离A大于任何其它两个邻区中的最大尺寸L的区域.这个例子里,F1,F2,F3都是个别区,同时全区是指F1+F2+F3.指示区的尺寸L与B,是从扫描指示区时探测中点获取的.如果是长测试管,必要时,可以扩大指示区,考虑声场几何与音响传输。

Issued: 1983-02-28 Revised: 2006-06-06Term Code: Design Control: DT Page 1 of 19 Supersedes: 1983-02-28 John Deere Standards are intended for use by Deere & Company, its divisions and subsidiaries. Suppliers who rely on them in furnishing products to or for the benefit of the Company must determine that they are in possession of the latest version. Distribution of the standards to parties other than John Deere Suppliers, whether with or without charge, are for information only and Deere & Company disclaims all responsibility for results attributable to the application of or compliance with such standards. The Company makes no representation, express or implied, that conformity ensures compliance with applicable law or other rules or regulations. Further, those who are in receipt of and elect to use the standards, agree to assume the responsibility for compliance with patents, as well as potential patent infringement.APPROVED FOR SUPPLIER DISTRIBUTIONJDS-D41Design Guidelines for Tolerances of Plastic PartsTable of Contents1Scope...............................................................................................................................................32How to Use JDS-D41.......................................................................................................................33Other Design Considerations...........................................................................................................34Basic Requirements.........................................................................................................................45Tolerances for Injection Molded Parts..............................................................................................56Tolerances for Compression Molded Parts......................................................................................97Tolerances for Rotationally Molded Parts........................................................................................108Tolerances for Thermoformed Parts................................................................................................139Tolerances for Fiberglass Spray-Up Parts.......................................................................................1510Tolerances for Reaction Injection Molded Parts..............................................................................1611Tolerances for Blow Molded Parts...................................................................................................1612References.......................................................................................................................................17 Summary of Changes from Previous Edition (For Information Only — Not Part of the Standard)..19JDS-D41 APPROVED FOR SUPPLIER DISTRIBUTIONList of TablesTable 1Material Types for Dimension Reference in Table 2 (6)Table 2Tolerances for Dimensions by Material Type and Tolerance Grade for Injection Molded Parts (7)Table 3Tolerances for Flatness and Concentricity for Injection Molded Parts (8)Table 4Dimensional Tolerances for Compression Molded Parts (9)Table 5Wall Thickness, Flatness and Concentricity Tolerances for Compression Molded Parts (10)Table 6Dimensional Tolerances for Rotationally Molded Parts (11)Table 7Additional Mold Tolerances for Rotationally Molded Parts (12)Table 8Tolerances for Feature Dimensions ≤ 600 mm (3 mm sheet thickness) of Thermoformed Parts (13)Table 9Additional Tolerances for Feature Dimensions > 600 mm (3 mm sheet thickness) of Thermoformed Parts (13)Table 10Tolerances for Angles (3 mm sheet thickness) of Thermoformed Parts (14)Table 11Tolerances for Other Features (3 mm sheet thickness) of Thermoformed Parts (14)Table 12Dimensional Tolerances for Fiberglass Spray-Up Parts (15)Table 13Dimensional Tolerances for Blow Molded Parts (18)List of FiguresFigure 1Example of General Molding Notes on Part Drawings (4)Figure 2Examples of Specifying Draft (5)Figure 3Example of Position Tolerance on Part Drawing (7)Figure 4Example of Concentricity on Part Drawing Using ABS Material and Fine Tolerance Grade (8)Figure 5Detail of Thickness Tolerance for Gel-Coat on Fiberglass Reinforced Plastic (16)JDS-D41 APPROVED FOR SUPPLIER DISTRIBUTION1 Scope1.1 JDS-D41 defines dimensional tolerances that may reasonably be expected on plastic parts manufactured by injection, compression, and rotational molding, thermoforming and fiberglass spray-up, reaction injection molding (RIM), and blow molding. Engineers should consult this standard when designing new parts for which plastic materials are being considered.1.2 Tolerances on plastic parts vary based on process, material, and dimension. JDS-D41 is organized by process. The format for each process differs, as each process has unique characteristics that affect its tolerances.2 How to Use JDS-D412.1 General tolerances represent the limits of variation under the most robust design and manufacturing conditions which meet C pk≥ 1.33. However, statistical process capability varies between suppliers and should be confirmed on a case-by-case basis.2.2 Commercial tolerances represent the limits of variation that can be achieved under normal manufacturing conditions.2.3 Fine tolerances represent narrower limits of variation obtainable under close supervision and process control. The cost of manufacturing parts to fine tolerances is generally higher than the cost of general and commercial tolerances.3 Other Design Considerations3.1 The John Deere design control unit is responsible for using accepted principles and procedures for geometric dimensioning and tolerancing (GD&T) according to ASME Y14.5M. Molded plastic parts shall be free of any feature depressions (sinks) or gates at datum targets. Datum targets should not be located on parting lines. Datum targets should be established during discussions with the supplier of the part.3.2 Regardless of economics, it is unreasonable to specify tight tolerances on parts that will operate over a wide range of temperatures. Dimensional changes due to thermal expansion may far exceed the specified manufacturing tolerances.3.3 Molded parts that require a secondary operation to achieve a required shape or dimension should be designed such that more material with a greater tolerance is given. This will allow proper material thickness for the process variation of a secondary machining operation.3.4 Part design should maintain a constant wall thickness whenever possible within design and process constraints. If variations in wall thickness are required, transitions should be as smooth and gradual as possible.3.5 Tolerance values should be increased when functional application allows.3.6 Tolerance values should include the effect of expected part warpage that can result from significant changes in wall thickness and process differences in shrinkage, flow directions, and cooling.JDS-D41APPROVED FOR SUPPLIER DISTRIBUTION4 Basic Requirements4.1 Dimensions4.1.1 Critical dimensions shall be specified on the drawing. All unspecified dimensions are obtained from the 3-dimensional geometric model. Refer to JDS-D41 for unspecified tolerances for the combinations of polymers and processes covered by this standard.4.1.2 The Dimensional Condition shall be specified as a general note according to ASME Y14.41 (seeFigure 1).Figure 1 Example of General Molding Notes on Part Drawings4.1.3 Use Bilateral Equally Distributed tolerances. Unilateral or Unequal Distribution tolerances are not recommended .4.1.4 Unless otherwise specified, all dimensions originate from datum targets. If datums are used instead of datum targets, the datums shall be identified as the origin by means of notes on the part drawing. 4.1.5Tolerances for secondary trim features shall be specified on the drawing.JDS-D41 APPROVED FOR SUPPLIER DISTRIBUTION4.2 Drafted SurfacesDraft on surfaces shall be shown in the model. Unless otherwise specified dimensions apply to Maximum Material Condition (MMC) of drafted feature of size (see Figure 2).Figure 2 Examples of Specifying Draft4.3 Wall ThicknessWall thickness shall be specified on the part drawing.4.4 Flatness and profileIf applicable, flatness and profile shall be specified on the part drawing.4.5 Drawing NotesAn example of general molding notes on a part drawing is shown in Figure 1.5 Tolerances for Injection Molded Parts5.1 Specification of Tolerances on Part DrawingsThe tolerance grade (general, commercial, or fine) that applies to as-molded (unmachined) surfaces shall be specified in the general notes of the part drawing (see Figure 1). Due to part and process cost implications, general grade tolerances should be selected as the default.5.2 Dimensional TolerancesThe dimensional tolerances applicable to a part depend on a combination of the specified material type and the applicable tolerance grade or class. See Table 1 for a list of materials and their corresponding material classes for determination of dimensional tolerances, which are shown in Table 2.5.3 Position ToleranceTable 2 can also be used as a guideline to establish minimum position tolerance.5.4 Wall Thickness ToleranceTolerances on wall thickness of 3 mm to 6 mm shall be ± 0.3 mm unless otherwise specified on the part drawing. Thicker wall sections generally result in increased shrinkage and greater dimensional variation. Tolerances on wall thickness > 6 mm shall be ± 0.5 mm unless otherwise specified.JDS-D41 APPROVED FOR SUPPLIER DISTRIBUTION5.5 Flatness and Concentricity ToleranceTable 3 specifies tolerances for flatness and concentricity applicable to the materials shown in the table. Profile tolerances may also be appropriate for certain parts. Profile tolerances should be included on part drawings as notes derived from discussions with molders on a case-by-case basis.5.6 Parting LinesParting line shall be considered when specifying tolerances in the direction of mold closing. Difficult-to-mold parts and low quality or worn molds may result in mold deflection at the parting line.Table 1 Material Types for Dimension Reference in Table 2MaterialSymbol Material NameMaterial Typefor Dimension ReferenceABS Acrylonitrile-butadiene-styrene AASA Acrylonitrile-styrene-acrylester A PA Polyamide APA11 Polyamide 11 (unfilled) BPA12 Polyamide 12 (unfilled) BPA6 Polyamide 6 (unfilled) BPA66 Polyamide 66 (unfilled) BPA610 Polyamide 610 (unfilled) BPA+GF Glass fiber reinforced PA6, PA66, PA610, PA611,PA612 APC Polycarbonate APE Polyethylene CPolyethylene terephthalate (amorphous) APolyethylene terephthalate (crystalline) APETPolyethylene terephthalate (filled) BPolymethyl methacrylate APMMAPolymethyl methacrylate (unfilled) dimension <150 mm BPolyoxylmethylene (polyacetal) (unfilled) dimension >150 mm CPOMPolyoxylmethylene (polyacetal) (filled) APolypropylene (unfilled) CPPPolypropylene (glass fiber filled or talc filled) BPP/EPDM Mixture of polypropylene and EPDM rubber BPPO Polyphenyleneoxide APPS Polyphenylene sulfide (filled) APVC Polyvinylchloride AThemoplastic polyurethane (hardness Shore A 70 to 90) CTPUThemoplastic polyurethane (hardness Shore D >50) BPolyester types 801, 802, 803, 804 AUPPolyester types 830 to 833.5 BJDS-D41 APPROVED FOR SUPPLIER DISTRIBUTIONTable 2 Tolerances for Dimensions by Material Type and Tolerance Gradefor Injection Molded PartsDimensional Tolerance (±)MaterialType ToleranceGrade mm %General 0.180.29Commercial 0.170.18AFine 0.110.12General 0.200.43Commercial 0.180.28BFine 0.110.12General 0.230.64Commercial 0.200.43CFine 0.180.28 Example of Calculating Applicable Dimension ToleranceCommercial tolerance for a dimension of 150 mm in Type A material:± [0.17 mm + (0.0018)(150 mm)] = ± 0.44 mmExample of Calculating Applicable Position ToleranceCommercial tolerance for a position dimension of 40 mm in Type A material (see Figure 3): ± [0.17 mm + (0.0018)(40 mm)] = ± 0.24 mm = Ø 0.48 mmFigure 3 Example of Position Tolerance on Part DrawingJDS-D41APPROVED FOR SUPPLIER DISTRIBUTIONTable 3Tolerances for Flatness and Concentricity for Injection Molded PartsFlatness (total mm)Concentricity (total mm)Feature DimensionTotal Area≤5500 mm 2 (74 × 74)Total Area>5500 mm 2 (74 × 74) to <22 500 mm 2 (150 × 150)Not ApplicableMaterial Commercial Fine Commercial Fine Commercial FineABS 0.77 0.50 1.53 1.10 0.46 0.24 PE(high density) 1.17 0.76 1.88 1.11 1.38 0.50 PE (low density)1.27 0.61 1.53 1.10 0.55 0.36 PA (all types)0.51 0.20 0.77 0.35 0.26 0.15PC 0.26 0.15 0.36 0.20 0.26 0.15 PET (all types) 0.66 0.40 1.17 0.66POM (all types)0.56 0.25 0.92 0.40 0.51 0.30PP 1.12 0.71 1.83 1.06 0.77 0.61 PPO 0.51 0.36 1.02 0.71 0.26 0.10 PVC 0.77 0.50 1.02 0.76 0.51 0.25Figure 4 Example of Concentricity on Part Drawing Using ABS Material and FineTolerance GradeJDS-D41 APPROVED FOR SUPPLIER DISTRIBUTION6 Tolerances for Compression Molded Parts6.1 Range of ApplicationThe data that follow apply to compression-molded parts made from polyester resin based sheet-molding compound (SMC). Excluded from this standard are parts molded using ultra high molecular weight polyethylene (UHMWPE).Note 1 SMC is commonly specified with high levels of fillers and glass fibers. This results in a compound with improved dimensional and thermal stability, particularly compared to thermoplastics.6.2 Specification of Tolerances on Part DrawingsThe tolerance grade (commercial or fine) that applies to as-molded (unmachined) surfaces shall be specified in the general notes of the part drawing (see Figure 1). Due to part and process cost implications, commercial grade tolerances should be selected as the default.6.3 Dimensional TolerancesDimensional tolerances (except wall thickness) are shown in Table 4.Table 4 Dimensional Tolerances for Compression Molded PartsDimension(± mm) by Dimension and Tolerance Grade(mm) ToleranceCommercial Fine > 0 ≤ 5 0.16 0.08> 5 ≤15 0.20 0.10> 15 ≤25 0.30 0.15> 25 ≤50 0.40 0.20> 50 ≤ 100 0.60 0.30 > 100 ≤ 200 1.00 0.50> 200 ≤ 400 1.60 0.80> 400 ≤ 800 2.40 1.20> 800 ≤ 1600 3.20 1.60> 1600 ≤ 3200 4.00 2.00 6.4 Wall Thickness ToleranceTolerances are based on a wall thickness of 3 mm to 6 mm. Thicker wall sections will lead to increased shrinkage and greater dimensional variation. Wall thickness tolerance shall be ±0.5 mm unless otherwise specified on the part drawing (see also Table 5). This wall thickness tolerance does not account for aging characteristics of the material.JDS-D41APPROVED FOR SUPPLIER DISTRIBUTION6.5 Flatness and Concentricity ToleranceTable 5 specifies tolerances for flatness and concentricity. Profile tolerances may also be appropriate for certain parts. Profile tolerances should be included on part drawings as notes derived from discussions with molders on a case-by-case basis.Table 5Wall Thickness, Flatness and Concentricity Tolerancesfor Compression Molded PartsTolerance (mm) Property Dimension (mm) Commercial FineWall ThicknessNot Applicable ±0.50 ±0.25 Total Area≤ 5500 mm 2 (74 × 74)Total0.40 Total 0.20 Total Area> 5500 mm 2 (74 × 74) to < 22 500 mm 2 (150 × 150)Total 0.70 Total 0.35 FlatnessTotal Area> 22 500 mm 2 (150 × 150) to < 90 000 mm 2 (300 × 300)Total 1.30 Total 0.65 Concentricity Not ApplicableTotal 0.30Total 0.157 Tolerances for Rotationally Molded Parts7.1 Specification of Tolerances on Part DrawingsThe tolerance grade (general, commercial, or fine) that applies to as-molded (unmachined) surfaces shallbe specified in the general notes of the part drawing (see Figure 1). Due to part and process cost implications, general grade tolerances should be selected as the default.7.2 Dimensional Tolerances7.2.1Dimensional tolerances [except wall thickness (clause 7.5)] are shown in Table 6.7.2.2 Because rotational molding is a low pressure process, large clamping forces between the mold halves are unnecessary. As a result, there is less control of dimensions perpendicular to the mold parting line. An additional 0.25 mm tolerance is added to dimensions that cross the parting line.7.2.3 Dimensions D and E (see Table 6) have tighter tolerances because the mold itself will restrict shrinkage.7.2.4 Inside dimensions of hollow rotationally molded parts are controlled by the free flow of the resin. Because these surfaces do not contact the mold, they cannot be held to consistent tolerances. This is particularly true of corners. Therefore, it is recommended not to dimension the interior of hollow rotationally molded parts.7.2.5 If secondary operations (for example, drilling and routing) remove molded surfaces, tolerances shall be specified. Residual molding stresses may cause the part dimensions to change significantly. This should be considered at the design stage, because such changes in dimensions are not included in the tolerances shown in this standard.7.2.6 Some rotationally molded parts require multiple cavities or multiple parts from a single cavity. Specified tolerances should be generous enough to account for differences in these cavities.Table 6 Dimensional Tolerances for Rotationally Molded PartsTolerance (± %) of DimensionMaterial Tolerance GradeA, B, CDEFGeneral 2.0 1.5 1.0 2.0 Commercial 1.0 0.8 0.8 1.0 PEFine 0.5 0.40.4 0.5 General 2.51.5 1.52.5 Commercial 2.0 1.0 1.0 2.0 PVCFine 1.0 0.50.5 1.0 General 1.0 0.8 0.8 1.0 Commercial 0.6 0.5 0.5 0.6 PA (all types)Fine 0.4 0.30.3 0.4 General 0.80.5 0.5 0.8 Commercial 0.50.30.3 0.5 PCFine 0.3 0.20.20.3• Dimensions A, B and C have unrestricted shrink. • Dimension D has partially restricted shrink. • Dimension E has restricted shrink.• Dimension F crosses the parting line. Add an additional 0.25 mm to the tolerance for dimensions that cross the parting line (see clause 7.2.2).7.3 Additional Mold Tolerance7.3.1 An additional mold tolerance should be added to each dimension for the mold types shown in Table 7.Table 7 Additional Mold Tolerances for Rotationally Molded PartsMold Type Dimension Additional Mold ToleranceMachined Molds All ± 0.25 mmCast Molds All ± (0.75 mm + 0.25% dimension)≤ 305 mm ± 1.6 mmFabricated Molds> 305 mm ± 3.2 mm7.3.2 Machined molds are ideal for smaller, shallower parts. Cast molds are more cost effective for parts with deep draws. Fabricated molds are typically used for large parts with simple geometry.7.4 Examples of Calculating Applicable Dimension TolerancesFollowing are two examples of calculating applicable dimension tolerances as a combination of mold tolerance from Table 7 plus material tolerance from Table 6.Commercial tolerance of dimension type A for a polyethylene (PE) part with a dimension of 150 mm formed in a cast mold:Tolerance = mold tolerance + material toleranceTolerance = ± [0.75 mm + (0.0025)(150 mm) + [(0.01)(150 mm)] = ± 2.62 mmCommercial tolerance of dimension type E for a polyethylene (PE) part with a dimension of 10 mm formed in a cast mold and crossing the parting line:Tolerance = mold tolerance + material tolerance + across parting line toleranceTolerance = ± {[0.75 mm + (0.0025)(10 mm)] + [(0.008)(10 mm)] + (0.25 mm)} = ± 1.10 mm7.5 Wall Thickness TolerancesWall thickness tolerances is dependent on geometry. Wall thickness tolerances of ± 30 % for the general tolerance grade, ± 20 % for the commercial tolerance grade, and ± 10 % for the fine tolerance grade are normal for parts with simple geometry. Most applications require specification of only a nominal and minimum thickness. Rotationally molded parts usually have gradually thickening walls on the outside corners and slightly thinner walls on the inside corners. This characteristic results in industry acceptance of tolerances applicable to the nominal walls and not to corners. Also, wall surfaces closer to the heat source tend to be thicker than those farther away.7.6 Flatness TolerancesFlatness tolerances are dependent on design of the part, particularly unsupported surface areas and the span of flat areas. Some designs can include domes or inter-wall supports to increase flatness. Flatness and profile tolerances should be included on part drawings as notes derived from discussions with molders on a case-by-case basis.8 Tolerances for Thermoformed Parts8.1 Range of ApplicationThe following tolerances apply to crystalline materials (for example: PP, HDPE, PA) and amorphous materials (for example: ABS, PC, PS, PC).8.2 Specification of Tolerances on Part DrawingsThe tolerance grade (commercial or fine) that applies to as-molded (unmachined) surfaces shall be specified in the general notes of the part drawing (see Figure 1). Customary practice limits tolerances of thermoformed parts to those surfaces that contact the mold. Due to part and process cost implications, commercial grade tolerances should be selected as the default.8.3 Dimensional TolerancesDimensional tolerances [except wall thickness (clause 8.4), angles (clause 8.5), and some other features (clause 8.6)] are shown in Table 8 for features of dimension ≤ 600 mm and in Table 9 for features of dimension > 600 mm.Table 8 Tolerances for Feature Dimensions ≤ 600 mm (3 mm sheet thickness) ofThermoformed PartsCrystalline Materials Amorphous Materials Feature Type Commercial Fine Commercial Fine Molded ≤ 600 mm ± 3.0 mm ± 1.5 mm ± 1.5 mm ± 0.8 mm Molded to Trimmed ≤ 600 mm ± 3.0 mm ± 1.5 mm ± 1.5 mm ± 0.8 mm Trimmed ≤ 600 mm ± 3.0 mm ± 1.5 mm ± 1.5 mm ± 0.8 mmTable 9 Additional Tolerances for Feature Dimensions > 600 mm (3 mm sheetthickness) of Thermoformed PartsCrystalline Materials Amorphous Materials Feature Type Commercial Fine Commercial Fine Molded >600 mm ± 0.7% ± 0.1% ± 0.7% ± 0.1% Molded to Trimmed >600 mm ± 0.7% ± 0.1% ± 0.7% ± 0.1% Trimmed >600 mm ± 0.7% ± 0.1% ± 0.7% ± 0.1% Example of Calculating Applicable Dimension ToleranceCommercial tolerance for a molded feature in a crystalline material with a nominal dimension of700 mm:± [3 mm + (0.007)(700 mm)] = ± 7.9 mm8.4 Wall Thickness Tolerance8.4.1 Wall thickness tolerances are based on a starting material thickness of 3 mm. Thicker sheets can lead to increased shrinkage and greater dimensional variation. Wall thickness tolerance shall be ±1.0 mm unless otherwise specified on the part drawing. Discussion with the molder should determine process limitations for starting material thickness > 3 mm and additional tolerances that are needed to account for aging characteristics of the material.8.4.2 Inside and outside corner wall thickness varies and depends on the thermoforming process (vacuum formed versus pressure formed). This should be considered when applying tolerances to corner radii.8.5 Angle TolerancesTolerances for angles (based on 3 mm sheet thickness) are shown in Table 10.Table 10 Tolerances for Angles (3 mm sheet thickness) of Thermoformed PartsCrystalline Materials Amorphous Materials Feature Type Commercial Fine Commercial FineMolded Angles ± 4° ± 3° ± 3° ± 2°Trimmed Angles ± 3° ± 2° ± 3° ± 2°8.6 Features of Size and Trimmed Radii TolerancesTolerances for features of size ≤ 25 mm and trimmed radii ≤ 25 mm are shown in Table 11. Features of size and trimmed radii > 25 mm are considered trimmed features and Table 8 applies.Table 11 Tolerances for Other Features (3 mm sheet thickness) ofThermoformed PartsCrystalline Materials Amorphous Materials Feature Type Commercial Fine Commercial Fine Feature of Size ≤ 25 mm ± 0.8 mm ± 0.5 mm ± 0.8 mm ± 0.5 mmTrimmed Radii ≤ 25 mm ± 1.5 mm ± 0.8 mm ± 1.5 mm ± 0.8 mm8.7 Depth of Draw ToleranceThe design of thermoformed parts should not require the depth of draw to exceed the part width. Thinning of walls occurs at the lowest inside corners and topmost outside corners. This should be considered when specifying tolerances.9 Tolerances for Fiberglass Spray-Up Parts9.1 Specification of Tolerances on Part DrawingsThe tolerance grade (commercial or fine) that applies to as-molded (unmachined) surfaces shall be specified in the general notes of the part drawing (see Figure 1). Customary practice limits tolerances of fiberglass spray-up parts to those surfaces that contact the mold. Due to part and process cost implications, commercial grade tolerances should be selected as the default.9.2 Dimensional TolerancesDimensional tolerances [except for wall thickness] are shown in Table 12.9.3 Gel-Coat9.3.1 Fiberglass spray-up parts are fibrous and require a gel-coat, veil coat, or barrier coat to achieve Class A appearance surfaces. This results in a laminated product. The gel-coat is typically 0.25 mm to 0.45 mm thick. Figure 5 is a detail of thickness tolerances (dimension G in the figure in Table 12).9.3.2 Radii located on the gel-coat Class A surface can be made to a minimum of 1 mm. Outside radii shall be at least 6 mm for a corner ≤ 135° and at least 3 mm for a corner > 135°.Note 2 As the size of the radius decreases, the radius becomes "resin-rich" and loses strength.Table 12 Dimensional Tolerances for Fiberglass Spray-Up PartsTolerances (±) of DimensionDrawing Dimension Feature Type Commercial Fine A,B,C,E,F Molded 0.1%mmA,C,E Trimmed 2.0mmB Drilled 2.0mmE Drilled 5.0D Molded In 3.0 mm 1.5 mmmmG Molded 0.6mmG Sanded 0.3Example of Calculating Applicable Dimension ToleranceCommercial tolerance for a molded feature (drawing dimension A) with a nominaldimension of 150 mm:± (0.001)(150 mm) = ±1.5 mmFigure 5 Detail of Thickness Tolerance for Gel-Coat on Fiberglass Reinforced Plastic 10 Tolerances for Reaction Injection Molded Parts10.1 Specification of Tolerances on Part DrawingsThe tolerance grade that applies to as-molded (unmachined) surfaces shall be specified in the general notes of the part drawing (see Figure 1). Customary practice limits tolerances of fiberglass spray-up parts to those surfaces that contact the mold.10.2 Dimensional TolerancesDimensional tolerances [except for wall thickness] are ± [0.125 mm + (0.001)(dimension)].Tolerance of nominal dimension 150 mm:Tolerance = ± [0.125 mm + (0.001)(150 mm)] = ± 0.28 mm10.3 Wall Thickness ToleranceTolerances are based on a wall thickness of 6 mm. Thicker wall sections will lead to increased shrinkage and greater dimensional variation. Wall thickness tolerance shall be ±1.5 mm unless otherwise specified on the part drawing.11 Tolerances for Blow Molded Parts11.1 Specification of Tolerances on Part DrawingsThe tolerance that applies to as-molded (unmachined) surfaces shall be specified in the general notes of the part drawing (see Figure 1). Customary practice limits tolerances of blow molded parts to those surfaces that contact the mold.11.2 Dimensional TolerancesDimensional tolerances are shown in Table 13.11.3 Profile Tolerances for Molded FeaturesMolded features can be held to a profile tolerance of 3mm in relation to the datum scheme.。

德标和国标,国际标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉slotted round head wood screws GB999 DIN97 开槽沉头木螺钉slotted countersunk head wood screws GB10010 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404 开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for wood constructions ISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉slotted knurled thumb screws with collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母T-slot nuts ISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes in one face GB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓cup head nib bolts74 DIN608 沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头wire rope clips85 DIN787 T型槽螺钉T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D）studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉hexagon socket set screws with conepoint ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88100 DIN923 开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86 107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86 110 DIN937 六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88 112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screws ISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screws ISO 2010 GB69-85119 DIN965 十字槽沉头螺钉cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk head screws ISO7047 GB820-85121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742 143 DIN1476 圆头槽销grooved pins with round head ISO8746GB/T13829.3144 DIN1477 沉头槽销grooved pins with countersunk head ISO8747 145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86 148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88 149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head 154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87 162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87 163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washersGB861.2-87165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washers assemblies GB9074.18-.23171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutchlining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws 185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical heads ISO8738194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO 7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84 200 DIN7990 钢结构用六角头螺栓hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameter appro.3d ISO7093 GB96-85208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。