下载文档原格式
商品名称：网关（4口耦合器）ASF.CP.4现场总线和以太网的接口功能具有4个总线接口总线工作状态指示，包括总线电压、短路报警等可读取出厂日期传输距离：1.2Km工作环境：-10～55℃，0～95%RH电源：220VAC, 50/60Hz大小234mm(W)*88.4mm(H)*70.3mm(D)商品名称：网桥ASF.CP.2传输距离1.2KM子网段之间信号转换装置总线电压测量功能总线短路报警功能兼容总线自愈技术工作环境：-10～55℃，0～95%RH电源: 110/220VAC, 50/60Hz大小：120mm(W)*86mm(H)*50mm(D)商品名称：26路干接点输入模块ASF.IM.26 具有26路干接点输入，4个LED输出每个口可配置为翘板开关模式或者复位开关模式可配置长按时间每个端口可配置ENABLE或者DISABLE场景工作环境：-10～55℃，20～80%RH电源: 110/220VAC, 50/60Hz大小：120mm(W)*86mm(H)*50mm(D)商品名称：时钟控制器ASF.TM.8电压：DC15-30V电流：200mA环境条件：环境温度：0-40C环境湿度：20%-90%RH最大存储110个日程最大存储96个特殊日时间段每个日程可一次性发送5个场景可以网路同步时钟尺寸：234mm(W)*88.4mm(H)*70.3mm(D)商品名称：电源模块ASF.PW.24V输出电压：DC15~24V（可调）总线输出电流：2A环境条件：环境温度：－10℃~＋40℃湿度：20%~80%对外输出2A电流输出电流测量功能，可在中央软件上读取短路保护功能尺寸：234mm(W)*88.4mm(H)*70.3mm(D)商品名称：4路继电器模块ASF.RL.4.16A6路继电器模块ASF.RL.6.16A8路继电器模块ASF.RL.8.16A每路最大负载16A故障复位功能每个区域可存储128个场景，场景运行时间0~120分钟具备多回路顺序延时启动功能可存储每一回路开关次数，闭合时间在EEPROM中，随时查询按动手开关得时候，状态会自动返回主控站每一场景具备网络开启（Enable）或关闭（Disable）功能控制回路的工作电压为安全电压DC12V~36V尺寸：234(W)x88.4(H)x70.3(D) /4路、6路、8路工作环境：-10～55℃，0～95%RH工作电源：220V，50/60Hz产品名称：4路负载反馈型继电器ASF.RL.4.16AF6路负载反馈型继电器ASF.RL.6.16AF8路负载反馈型继电器ASF.RL.8.16AF 每路最大负载16A可测量每回路电流值，并传送到中央监控电脑故障复位功能每个区域可存储128个场景，场景运行时间0~120分钟可存储每一回路开关次数，闭合时间在EEPROM中，随时查询按手动开关的时候，状态会自动返回主控站测量电流精度0.1A收到总线场景命令后，可立即返回执行完成后各回路的实际电流值每一场景具备网络开启（Enable）或关闭（Disable）功能尺寸：234(W)x88.4(H)x70.3(D) /4路320(W)x88.4(H)x70.3(D) /6路320(W)x88.4(H)x70.3(D) /6路工作环境：-10～55℃，0～95%RH工作电源：220V，50/60Hz商品名称：4路自锁负载反馈型继电器ASF.RL.4.20AZSF 6路自锁负载反馈型继电器ASF.RL.6.20AZSF 每路最大负载20A具备机械自锁继电器装置，停电切换的状态下可保持继电器开关状态不变可测量每回路电流值，并传送到中央监控电脑，故障复位功能每个区域可存储128个场景，每个场景下任何一个回路延迟执行时间为655.35秒触点寿命≥10万次收到总线场景命令后，可立即返回执行完成后各回路的实际电流值每一场景具备网络开启（Enable）或关闭（Disable）功能具备过零断开技术尺寸：234(W)x88.4(H)x70.3(D) /4路320(W)x88.4(H)x70.3(D) /6路工作环境：-10～55℃，0～95%RH工作电源：220V，50/60Hz商品名称：4路调光模块ASF.DM.4.5A6路调光模块ASF.DM.6.3A4路负载，每路3A6路负载，每路2A故障复位功能可存储128个场景每个回路场景下各个回路的软启动时间为0~655.35秒，延迟时间为0~655.35秒整个模块可以更改调光曲线具备可控硅短路保护功能采用高性能的晶体闸流管THYRISTOR（可控硅）调光电流上升时间大于200微妙每一场景具备网络开启（Enable）或关闭（Disable）功能收到总线场景命令后，可立即返回执行完成后各回路的实际电流值工作环境：-10～55℃，0～95%RH工作电源：220V AC, 50/60Hz尺寸：234(W)x88.4(H)x70.3(D) /4路320(W)x88.4(H)x70.3(D) /6路商品名称：ASF.FL.4 4路荧光灯调光模块最大存储128场景一个场景下任何一个回路的延迟执行时最大655.35秒，软启动时间655.35秒可设置中止场景整个模块可以设置独立的调光曲线每一回路配置16A继电器，当亮度调节为0时，自动断开继电器适合日光灯、金卤灯、钠灯调光，配合可调电子镇流器使用输入电源：220VAC±10%整机无负载功耗：15W供电电压：220VAC,50Hz工作环境：工作温度-10℃～+55℃工作湿度20%～80%存储温度-10℃～+55℃存储湿度10%～95%大小：120mm(W)*86mm(H)*50mm(D)商品名称：ASF.FLDSI.4 4路DSI接口模块最大存储128场景一个场景下任何一个回路的延迟执行时最大655.35秒，软启动时间655.35秒可设置中止场景每个回路可以设置独立的调光曲线每一回路配置16A继电器，当亮度调节为0时，自动断开继电器适合日光灯、金卤灯、钠灯调光配合可调光电子镇流器使用供电电压：220VAC,50Hz工作环境：工作温度-10℃～+55℃工作湿度20%～80%存储温度-40℃～+55℃存储湿度10%～95%大小：120mm(W)*86mm(H)*50mm(D)商品名称：6路LED调光模块ASF.DM.LED.6.3A 1728级PWM调光，可将LED调节到1%亮度最大存储128场景一个场景下任何一个回路延迟执行时最大655.35秒，软启动时间655.35秒可设置中止场景每个回路可以设置独立的调光曲线工作环境：工作温度-10℃～+55℃工作湿度0～95%外形尺寸234(W)x88.4(H)x70.3(D)商品名称：4路8A调光箱ASF.DM.4.8A4路10A调光箱ASF.DM.4.10A4路20A调光箱ASF.DM.4.20A6路8A调光箱ASF.DM.6.8A6路10A调光箱ASF.DM.6.10A6路20A调光箱ASF.DM.6.20A12路8A调光箱ASF.DM.12.8A12路10A调光箱ASF.DM.12.10A12路20A调光箱ASF.DM.12.20A电源：三相五线制电压：220V±10%频率：50±1Hz环境条件：环境温度：-10℃～55℃工作湿度：20%～90%每回路输出电流：8A/10A/20A，单路最大20A可存储128个场景一个场景任何一个回路的延迟执行时间最大为655.35秒，软启动时间为0~655.35秒可设置终止场景每个回路可以设置独立的调光曲线可控硅短路（过流）保护功能电流上升时间大于200微妙可读取每一回路的电流值，当电流异常时自动报警每一回路具备手动强制性开关采用超静音电路商品名称：可编程面板7键面板ASF.IP.7单联控制面板ASF.IP.2双联控制面板ASF.IP.4四联控制面板ASF.IP.8电压：DC12～30V电流：50mA环境条件：环境温度：-10℃～55℃工作湿度：20%～80%带红外线遥控功能每个模块都具有网络开启及关闭功能可发送全局场景命令每个按键在选择按下发送场景或奇偶次按下发不同场景时，还可选择实时调光功能每个按键都有对应的LED输出，LED灯颜色可选每个面板可以设置12组相关场景，每组20个场景每个按键可以设置三种输入方式（按下发送场景、奇偶次按下发不同场景按下、松开发不同场景）商品名称：4.3寸彩色触摸屏ASF.TS.CL47寸彩色触摸屏ASF.TS.CL7电压：DC12～30V环境条件：环境温度：0℃～40℃工作湿度：20%～90%亮度可调的背景LCD软件和硬件网络ID设定基于Windows 平台操作系统32bit真彩色图形分辨率480×272（4.3寸）图形分辨率800×480（7寸）商品名称：多功能输入模块ASF.IM.0可向传感器提供不同的供电电压，9V、12V、15V 输入电压：DC15V~30V，输入电流：50mA输入信号：开关量输入0~5V和0~10V输入环境条件：环境温度：-20℃～55℃工作湿度：20%～90%可以任何型号的传感器配合使用接收传感器0~5V或0~10V的模拟信号接收开关型的传感器信号可设定场景延迟发送时间网络ID码和设备ID码设定无需断电的软复位功能可一次性发送三个独立的场景可实时读取还有多长时间会发送XX场景可读取最后一次的测量值商品名称：照度感应器ASF.PS.9电流：15mA，工作电源：12~36V DC环境条件：环境温度：-10℃～60℃工作湿度：0%～95%需要多功能输入模块配合组成：控制器+感应种类：室内/室外/阳台，室外型防水测量范围：200~2000Lux（底照度型）200~20000Lux（室内型）20000~200000Lux（日光型）准确度：正负7%商品名称：红外动态传感器ASF.IR.36（吸顶式）ASF.IR.11（壁挂式）延时范围：0~12分钟电流：15mA工作电源：9~13.5V DC环境条件：环境温度：-10℃～60℃工作湿度：0%～95%需要多功能输入模块配合感应方式：红外+微波复合感应覆盖面积：吸顶式直径7~9米壁挂式直径12~18米商品名称：4路窗帘控制模块.4每个模块都具有网络开启及关闭功能每组窗帘控制回路都具有LED输出每组窗帘控制回路都具有手动调节功能每组窗帘控制可以选择直接运行或归零再运行两种模式每组窗帘控制回路可以独立设置行程时间每组窗帘控制回路可以独立设置延时执行时间每个场景可以设置延时执行时间模块执行总线场景命令后可以选择反馈或不反馈各个回路实际开关状态信息针对电机电感特性，模块具有继电器触点保护功能继电器触点寿命大于或等于10万次最大可存储200个场景输入电源：220V±10%整机无负载功耗：5W工作环境：工作温度-10℃～+55℃工作湿度20%～80%存储温度-40℃～+55℃存储湿度10%～95%外形尺寸234(W)x88.4(H)x70.3(D)商品名称：酒店客房专用模块ASF.EH.301路电量测量4路继电器输出2路脉冲式水表测量4路干接点输入输入电源：12VDC/30VDC±10%整机无负载功耗：4W工作环境：工作温度-10℃～+55℃工作湿度20%～80%存储温度-40℃～+55℃存储湿度10%～95%大小：115mm(W)*110mm(H)*21mm(D)商品名称：4路继电器模块ASF.RL4.10A6路继电器模块ASF.RL6.10A每个模块都具有网络开启及关闭功能每个回路都具备LED输出接口每个回路可以独立设置延迟执行时间每个场景可以设置延迟执行时间模块执行总线场景命令后可选择反馈或不反馈各个回路实际开关状态信息具有继电器触点保护功能继电器触点寿命大于或等于10万次继电器具有自锁功能，即断电后可自动恢复到断电前的开关状态输入电源：12-24V整机无负载功耗：4W工作环境：工作温度-10℃～+55℃工作湿度20%～80%存储温度-40℃～+55℃存储湿度10%～95%大小：120mm(W)*86mm(H)*50mm(D)商品名称：4路2A调光模块ASF.DM.4.2A电流上升时间大于200微秒每个模块都具有网络开启及关闭功能每个回路都具备LED输出接口每个场景可以设置延迟执行时间模块可以接收实时调光命令模块执行总线场景命令后可选反馈或不反馈各个回路实际亮度状态信息每个模块可存储128个场景输入电源：12-30V整机无负载功耗：4W工作环境：工作温度-10℃～+55℃工作湿度20%～80%存储温度-40℃～+55℃存储湿度10%～95%大小：120mm(W)*86mm(H)*50mm(D)商品名称：风机盘管控制面板（温控器面板）ASF.FP.3 配合ASF.FI.HAVC.B使用可直接控制风机盘管自带温度传感器具备多种颜色可选输入电源：12VDC/24VDC±10%整机无负载功耗：2W工作环境：工作温度-10℃～+55℃工作湿度20%～80%存储温度-40℃～+55℃存储湿度10%～95%大小：90mm(W)*120mm(H)*60mm(D)商品名称：温控面板接口模块ASF.FI.HAVC.AASF.FI.HAVC.B ASF.FI.HAVC.A:每个模块可以enable或者disabled可外接传统2管制或者4管制的温控面板1个数字温控器接口外接温控器和内部自动控制风机盘管切换功能风速自动调节enable和disabled功能风速自动调节阀值设置可以存储100个场景ASF.FI.HAVC.B：每个模块可以enable或者disabled通过485口接爱瑟菲温控器面板可以控制多达20个爱瑟菲温控器面板最大存储100个场景工作环境：-10～55℃，0～95%RH电源: 12～36V总线供电大小：120mm(W)*86mm(H)*50mm(D)商品名称：电话控制模块ASF.TI.5电话控制装置-定时控制，手动控制使用一般电话空通过电话DTMF远程发送场景工作环境：温度:-10℃～55℃湿度：20%~80%电源: 12～30V DC大小：120mm(W)*86mm(H)*50mm(D)商品名称：无线网桥ASF.CP.WL.2最大距离500m（空旷地区）每个模块可以enable或者disabled射频信号功率测量功能频道选择功能可任意选择255个频道可外接多重增益的天线315或者433Mhz工作功率工作环境：温度:-10℃～55℃湿度：20%~80%电源: 12～36V DC大小：120mm(W)*86mm(H)*50mm(D)商品名称：射频遥控器基站模块ASF.RM.BASE 最大距离500m（空旷地区）每个模块可以enable或者disabled射频信号功率测量功能频道选择功能可任意选择255个频道可外接多重增益的天线工作环境：温度:-10℃～55℃湿度：20%~80%电源: 12～36V DC大小：120mm(W)*86mm(H)*50mm(D)商品名称：DMX 输出模块ASF.DMX30512F 512路DMX512(1990版)输出可以存储128个场景每个通道的软启动时间最大为65.35秒需要序列发生器配合实现“节目”功能可以多个DMX512并联连接，实现更多的场景工作环境：温度:-10℃～55℃湿度：20%~80%电源: 12～30V DC大小：120mm(W)*86mm(H)*50mm(D)商品名称：序列发生器ASF.GE.DMX30SEO可存储9个序列，每个序列可存储50个场景可配置中止场景可配置循环或者不循环执行序列扩充EEPROM存储单元后，可以存储更多序列工作环境：温度:-10℃～55℃湿度：20%~80%电源: 12～30V DC大小：120mm(W)*86mm(H)*50mm(D)商品名称：红外自学习模块ASF.IR.1可用波形存储方式存储没有规律的红外码，红外码内容可通过总线上传至主控站可以通过网络启动场景无需断电的远程软件复位功能具有远程编程、检测和管理功能模块可执行总线发来的全局场景命令最大存储30个红外码序列，每个序列存储16个红外码输入电源：12VDC/24VDC±10%整机无负载功耗：4W工作环境：工作温度-10℃～+55℃工作湿度20%～80%存储温度-10℃～+55℃存储湿度10%～95%大小：120mm(W)*86mm(H)*50mm(D)商品名称：232接口模块ASF.IF.232提供快思聪，AMX，VITY等系统的接口接口通讯速率96000bps通讯格式为：8data，1stop，No Parity可将总线场景转发到232接口，也可以将外部232命令转化成场景发送到内部总线可接受外部单回路亮度控制命令工作环境：工作温度-10℃～+55℃工作湿度20%～80%外形尺寸234(W)x88.4(H)x70.3(D)商品名称：ASF.IF.DALL.1 DALI接口模块可以控制64个DALT设备最大存储100个场景每一个场景可以设置为对应的DALT的16个组+亮度值，或者直接对应16个场景中的一个电源：12-36V总线供电工作环境：工作温度-10℃～+55℃工作湿度20%～80%大小：120mm(W)*86mm(H)*50mm(D)照明控制系统的原理及组成部分系统组成图【术语定义】●子网：用于寻址，每个设备都需要定义一个子网号，从属于不同子网的设备间通行必须通过专门网关路由中转，通常一个楼层或一个建筑物内的设备定义为一个子网；●子网网段：物理上用一根485总线连接的设备的总和，一个网段最多接32个设备，一个子网可以由多个子网网段组成；●网桥：由于485总线只能支持1.2公里长度，当子网网段或子网之间距离较长的时候，需要用网桥来延长距离；●网关：网关的作用有两个，其一，可以作为总线耦合器连接多个子网网段，其二，可以作为485总线和以太网之间的接口；●场景控制器：储存场景用，连接功率输出模块，用于功率输出模块和485总线之间的通讯、命令解释和执行，12路、24路大功率输出模块已经内置场景控制器；●中央管理电脑：定时器程序设置处理各种信号和警报图形化监控能源管理记录自动记录所有数据信息和日志●远程控制：PDA控制、电话/手机控制、互联网企业部分业绩（范文素材和资料部分来自网络，供参考。
二 . 数字媒体信息发布系统采购清单：厦门海事局多媒体触摸显示设备清单
说明：
1.本次竞价为整体采购，投标人报价时须写明单价及总价、产品的详细配置参数，投标报价包含货物制造、辅材、运输、安装调试、售后服务及技术培训
等交付采购人使用前所有可能发生的费用，定标后不再增补任何费用。
2. 需在4处位置安装：东渡局（湖里航运中心）、鹭江局（国际邮轮中心）、同安局（翔安区政府旁）、五缘湾.
3.本系统定于5月1日启用，不能在5月1日前完成安装调试的供应商请勿参与竞价,如出现未能到期供货的情况，中标商将承担所有的经济损
失及相应责任。
See Close-Up in 700TVL High Res TVEASILY CONNECT TO TV OR DVROSDCONTROL THE VIDEO IMAGES WITH ON-SCREEN DISPLAYPOWERFUL DAY & NIGHT VISION OF 131FT / 40M IP67 DURABLE WEATHERPROOF METAL CASINGWIDE DYNAMIC RANGE TOSEE CLEAR IMAGES IN ANY LIGHTSUPER CRYSTAL CLEAR COLOR700TVL 1/3" SONY 'EFFIO' CCD VIDEOSEE MORE WITH ADJUSTABLE FOCUS & 4x ZOOMDETER VISIBLE CAMERA & 4 STICKERS DETER CRIME WDR 700TVLPro quality 700 TV lines, day/night protection from above!• See more with high resolution 700 TV lines color 1/3” Sony ‘Effi o’ video, powerful infrared night vision & wide dynamic range for clear images in any light• Use the On-Screen Display (OSD) controller & built-in software to customize the camera settings for professional quality v ideo surveillance• Easily mount to walls or ceiling with heavy duty, vandal-resistant aluminum construction & IP-67 weatherproof rating for all conditions• Fight back against crime by deterring intruders & protecting your property at all hours of the day & night• Plug into a DVR for recording or your TV’s video-in socket for immediate surveillance • Perfect for home, offi ce, retail or commercial surveillance, indoors or outdoors in any weatherUltimate Optical Zoom Dome CameraPRO-781™C A M E R ASWPRO-781CAMFor more information on this product visit es2XU 3URPLVHSwann stands by its Lifetime Support promise to makeadvanced security easy to use, install and maintain.Everything is in the pack but if you need it, Swann’s helpdesk is available with extended hours for the life of the product. Swann products are also backed by a 12 monthmanufacturer’s warranty.promisetomake T HES WA N N P R OMIS ET HES WA N N P R OMI S EInstallation is easyDo-it-YourselfInstalling this Swann product is simple. For instructions, tips and videos see the operating instructions in this pack or visitProfessional InstallationNeed extra help?We have an installer in your region!For more visitWhat’s in the boxAll installation accessories included • PRO-781™ Dome Camera • OSD Controller • BNC Cable 60ft / 18m • • • • Operating Instructions • Speci fi cationsVideoImage Sensor Color 1/3” Sony ‘Effi o’ CCD Video Quality700 TV LinesNumber of Effective Pixels NTSC: 976 x 494 / PAL: 976 x 582Minimum Illumination 0 Lux (IR on)Day/Night Mode Color during day / switches to B&W at night White Balance Automatic / Custom / Manual Electronic Shutter 1/60 - 1/100,000 NTSC1/50 - 1/100,000 PALGain ControlAutomatic / Manual Backlight Compensation Adjustable Wide Dynamic RangeAdjustableLensVari-focal 2.8mm ~ 12mmViewing Angle23 ~ 81 degreesNight VisionNight Vision Distance 98ft / 30mNumber of Infra-Red LEDs 21Infra-Red Wavelength 850nmInfra-Red LED Life10,000 hoursGeneralOperating PowerDC 12VOperating Temperature -4°F ~ 113°F / -20°C ~ 45°C Body Construction AluminumDimensions – Camera 5.9” x 5.9” x 3.9”150mm x 150mm x 100mm Weight – Camera 2.03lbs / 922g Cable Length60ft / 18mCodesSwann Code SWPRO-781CAM UPC 815849013230BNC Cable 60ft / 18m BNC to RCA Adapter Power Adapter & SplitterMounting Screws & PlugsOperating InstructionsTheft Deterrent Stickers x 4Ultimate Optical Zoom Dome CameraPRO-781™Advanced customizable features available through OSD(On-Screen Display) controllerHeavy duty,vandal-resistantaluminium construction Remotely adjust camera settings5.9” / 150mm DiameterEasily mount to walls or ceilingsRemove and re-attach base with Allen key for easy DIY installation Do-it-YourselfInstalling this Swann product is simple. For instructions, tips and videos see the operating instructions in this pack or visit Professional InstallationNeed extra help? We have an installer in your region! For more visit PRO-781Monitor(not included)DVR(sold separately)OSD ControllerInstallation is easy。
三星电子（Samsung摄像机22x光学、一体化摄像机SCC-C4203AP一体化摄像机日夜型、32光学、128宽动态摄像机SCC-C4207P日夜型、32光学、SCC-C4233P高清摄像机1/4 英寸SUPER HAD CC芯片；内置3.6-79.2mm 非球面镜头，22倍光学变焦，10倍数码放大；具有日夜彩色黑白自动转换功能，黑白最低照度可达0.005Lux，提供128个预置点；有强大的画面动态检测功能并提供报警输出；通过电压控制接口或RS-485接口灵活地实现远程控制功能；体积小巧60.5X59.5X109.5 毫米，可放进7寸球罩，性价比高。
1/4英寸宽动态彩色黑白转型Ex-View HAD CCD芯片与数码信号稳定处理技术（DIS）；动态范围是普通摄像机的128倍。
内置3.55-113mm非球面镜头，32倍光学变焦，10倍数码放大；夜视功能，最低照度达0.002LUX;提供128个预置点；独有的8个马赛克隐私遮挡区域，用于需要隐私遮挡的地方；有强大的画面动态检测功能并提供报警输出；通过电压控制接口或RS-485接口灵活地实现远程控制功能；有正/负片，行/场清晰度等视频功能控制；提供最多20个字符的摄像机标训设定功能。
能根据照度实现彩色/黑白的自动转换。
具有优良的图像处理功能可放进7寸球罩1/4英寸Ex-View HAD PS CCD芯片，宽动态范围是普通摄像机的160倍；水平分辨率达到彩色540线，黑白570线；具有DNR数字降噪技术；32倍光学变焦，16倍数字放大；日夜彩色黑白自动转换功能，最低照度彩色达到0.4Lux，黑白0.036LUX ；128个预置点；独有的16个马赛克隐私遮挡区域，用于需要隐私遮挡的地方；有强大的画面动态检测功能并提供报警输出；可以通过电压控制接口或RS-485接口灵活地实现远程控制功能；本机体积小巧60.5X59.5X125.2毫米，性价比高。
380060004600彩色、高清、迷你半球摄像机SCC-B5203P彩色半球摄像机SCC-B5351GP1/3英寸Super-HAO IT CCD与数字信号处理技术（DSP，清晰度高达520线；外型精美小巧，尺寸只有85（?）X54（H） mm有黑色、银色外壳可选，适合各种需要隐蔽安装的场所使用。
奇美37寸液晶屏简介一、概述V370H1-LOA 是 CHI-MEI 公司(奇美)2006 年生产的液晶屏,带有 20 支冷阴极荧光灯作背光源。
两路ＬＶＤＳ接口，支持分辨率为 1920×1080 的 HDTV，能显示 16.7M 色彩（8bit/基色）。
内设有背光源的逆变器。
▪超宽视角–支持广视角技术▪高亮度（500 尼特）▪高对比度> 1000:1▪快速响应时间< 8 ms▪色饱和度高(NTSC 75%)▪高清分辨率(1920 x 1080 像素)▪单一数据使能控制模式▪ LVDS (低压差分信号) 接口注1注 2：表面处理的规格是暂定的，奇美公司有权更改二、极限参数注（1）温度和相对温度范围如图1所示（a）最大相对湿度90%（Ta＜40ºC）（b）湿环温度计最大是39ºC（Ta＞40ºC）（c）无凝露注（2）屏的最大运行温度是基于屏表面温度小于等于60ºC，若超过60ºC应缩小运行温度范围，这一点在产品的设计时应重视。
注（3）11ms，半正弦波±x，±y，±z方向各一次。
注（4）10～200Hz，持续10分钟，X、Y、Z方向各一次。
注（5）在做冲击和震动试验时，夹具应将模块夹紧，模块应有刚性，不应被夹具固定时出现变形。
图1 温度和相对湿度范围图注（1）：如超过最大值，屏可能会产生永久性损坏，正常工作条件下的运行功能将受到限制。
注（1）制。
注（2）：潮气不凝露或冰结。
注（3）：控制信号是指on/off控制和内部PWM控制信号。
三、电气特性注（2）：测试电路如下注（3）：表中所列的电源供电电流测试条件是：VCC=18V/12V，Ta=25±2℃，fV=60Hz，屏的画面图形如图4、5、6所示。
图2 冲击电流测试电路图3 Vcc上升时间是470μs图7逆变器电源和控制信号时序图注（1）：灯电流测量须用高频电流表。
类别名称图片型号7寸数字触摸液晶显示室内机TCL280-KDS2 7寸数字触摸液晶显示室内机TCL280-KDS2L
7寸数字触摸液晶显示室内机TCL300-KDS2M
内
机
7寸数字触摸液晶显示室内机TCL300-KDS2L
室
内
机
内
机
7寸数字触摸液晶显示室内机TCL600-KDS2L
10.2寸数字触摸液晶显示室内机TCL600-KDS1
10.2寸全功能数字触摸液晶显示室内机TCL800-KDS1
二次确认机（数字）TCL-MA1
无屏单元门口机(数码管显示)TCL-KDM5D
无屏围墙机(数码管显示)TCL-WA5D
口
机
/
围
墙
机
7寸数字真彩液晶单元门口机TCL-KDM27寸数字真彩液晶显示围墙机TCL-WA2
门
口
机
/
围
墙
机
10.2寸数字真彩液晶单元门口机TCL-KDM1
10.2寸数字真彩液晶显示围墙机TCL-WA1
无屏室内副机TCL-DSFD 视
7寸彩色室内副机TCL-KDF2管理中心机台式10.2寸彩色触摸液晶显示管理机TCL-GZ1L TCL智能家居管理系统软件V1.0(全功能)TCL-MS-V2.0TCL智能家居管理系统软件V1.0(基本版)TCL-MS-V1.0服务器
管理中心服务器（一套）EVOC-810B 安防模块（16防区）TCL-BG16手机短信收发软件模块
TCL-GSM-V2.0.1手机短信GSM模块
ETPRO-101A1电源电源模块
B50412V10A 无屏门口机/围墙机嵌墙盒扩展模块副机/厨卫电
视
软件部分。
CHI HSIN ELECTRONICS CORP .PreliminaryProduct SpecificationsCustomer Description7” TFT LCD ModuleModel Name LS700AT9001 Date 2009/05/13 Doc. No.Revision 02Customer ApprovalDateThe above signature represents that the product specifications, testing regulation, and warranty in the specifications are acceptedEngineeringCheck Date Prepared DateRyan Chu2009.05.13 William Chang 2009.05.13Head Office & Factory : No. 12, Nanke 8th Rd., Tainan Science-Based Industrial Park, Taiwan,74144 R.O.C.TEL: +886-6-5889980 FAX: +886-6-5051522PreliminaryCONTENTSNo. ITEM PAGE 0RECORD OF REVISION3 1 SUMMARY4 2 FEATURES43 GENERAL SPECIFICATIONS4 4ABSOLUTE MAXIMUM RATINGS4 5 ELECTRICAL CHARACTERISTICS 5 6 DC CHARATERISTICS 6 7 AC CHARACTERISTICS 6-7 8 OPTICAL CHARATERISTIC 7-9 9 INTERFACE10-11 10 BLOCK DIAGRAM 12 11 QUALITY ASSURANCE 12 12 OUTLINE DRAWING 13 13 PACKAGE INFORMATION 15 14 PRECAUTIONS16-17PreliminaryRECORD OF REVISIONSRevision Date PageDescription01 2008/12/10 All New Creation02 2009/05/13 4Add the Front Polarizer Type in the table of general specifications.5Add Max. Current Value into the table ofBacklight Driving for Power Consumption. 5 Fine tune Operating Conditions6 Fine tune AC Timing CharacteristicsPreliminary1. SUMMARYLS700AT9001 is a transmissive type color active matrix liquid crystal display (LCD), which uses amorphous thin film transistor (TFT) as switching devices. This panel has a 7.0 inches diagonally measured active display area with SVGA (800 RGB x 600) resolution. The following describes the features of this product.2. FEATURES● 7” (diagonal) inch configuration ● SVGA (800×600 pixels) resolution3. GENERAL SPECIFICATIONSParameter Specifications Unit LCD size 7(Diagonal) Inch Display mode Normally white, Transmissive type Number of Pixel 800 RGB x 600 Dot Display Color 262k color Active area 141.60(H) x 106.20(V) mm Pixel Pitch 59 (H) x 177 (V) um Pixel Configuration RGB-StripeNTSC 45 % Interface Digital 18bit RGB Polarizer Type(the Front) Anti-Glare Type View Angle L/R/U/D (CR>10) 70,70,50,70 Degree View Angle direction 6 o’clock Outline Dimension 154 (H) x119.2 (V) x 5.1 (D) mm Weight (135) gOperation -10~70℃Temperature RangeStorage -20~80℃4. ABSOLUTE MAXIMUM RATINGSItem Symbol Condition Min. Max. Unit RemarkVcc GND =0 -0.3 6 V -AVDD, GND =0 -0.3 13.5 V - V GH GND =0 -0.3 +42 V -Power Voltage V GL GND=0 VGH-42 +0.3 V - Note ：1. All of the voltages listed above are with respective to GND=VSSA=0V2. Device is subject to be damaged permanently if stresses beyond those absolute maximum ratings listed above.Preliminary 5. ELECTRICAL CHARACTERISTICS5.1. Operating conditions:5.2. Backlight Driving for Power ConsumptionParameter SymbolMin.Typ.Max.UnitRemark LED current I LED -120150mANote1 LED voltage V LED 9.09.9 - VLED Life Time - 10000 - - Hr Note 2Note 1 : There are 6 Groups LED shown as below , VNote 2 : Brightess to be decreased to 50% of the initial value. The Life time base on the operatingof Typical Current 120mA.ValuesItem SymbolMin. Typ.Max.Unit Note Digital Power Supply Voltages VCC 3.0 3.3 3.6 VDigital Supply CurrentConsumptionIVCC - 3040 mABlackPattern Analog Power Supply Voltage AVDD 10.5 1213.5 VAnalog Supply CurrentConsumptionIAVDD - 3646 mA BlackPattern Gate Driver Positive SupplyVoltageVGH 14 1720 V Gate Driver Positive SupplyCurrentIVGH - 1 2 mABlackPattern Gate Driver Negative SupplyVoltageVGL -8 -7 -6 V Gate Driver Negative SupplyCurrentIVGL - 1 2 mABlackPattern Common Electrode DrivingVoltageVCOM - 4.3- V BlackPattern Input Logic Signal HighThresholdVIH 0.8Vcc- Vcc VInput Logic Signal LowThresholdVIL 0 -0.2VccVInput levev V1~V5 Vref1 0.4AVDD- AVDD-0.1V Gamma correctionvoltage inputInput levev V6~V10 Vref2 0.1 - 0.6AVDD V Gamma correctionvoltage inputPreliminary6. DC CHARATERISTICSRatingParameter Symbol Min. Typ. Max.Unit ConditionLow level input voltage V IL 0 - 0.2VCC VHight level input voltage V IH 0.8VCC - VCC V7. AC CHARATERISTICS7.1 AC Timing Characteristics7.2 AC Timing DiagramsSpec.Parameter Symbol Min. Typ. Max.UnitCLK Frequency Fcph - 39.79- MHz CLK Period Tcph - 25.13- ns CLK Pulse Duty Tcwh 40 50 60 % DE Period T DEH +T DEL 1000 1056 - Tcph DE Pulse Width T DH - 800 - Tcph DE Frame Blanking T HS 10 28 110 T DEH +T DEL DE Frame Width T EP - 600 - T DEH +T DEL Data Setup Time Tdsu 6 - - ns Data Hold Time Tdhd 6 - - ns DEN Setup Time Tesu 6 - - nsPreliminary7.3 Data input format7.4 Reset TimingPreliminary8. OPTICAL CHARATERISTICTa=25±2, ILED=℃120mANote 1: Definition of viewing angle rangeFig. 8-1 Definition of viewing angleNote 2: Test equipment setup:After stabilizing and leaving the panel alone at a driven temperature for 10 minutes, themeasurement should be executed. Measurement should be executed in a stable, windless, and dark room. Optical specifications are measured by Topcon BM-7 luminance meter 1.0° field of view at a distance of 50cm and normal direction.Item Symbol Condition Min Typ Max Unit NoteTR - 5 10ms Response time TF Θ=0- 15 20ms (2) Contrast ratio CR At optimizedviewing angle300 400 -- (3) Wx 0.27 0.32 0.37Color Chromaticity White Wy Θ=00.27 0.32 0.37(4) ΘR - 70 -Hor.ΘL - 70 -φH - 50 -Viewing Angle Ver.φL CR 10≧- 70 -Degree (5) Brightness - - (200)250 - cd/m 2Center ofDisplayPreliminaryFig. 8-2 Optical measurement system setupNote 3: Definition of Response time:The response time is defined as the LCD optical switching time interval between “White” state and“Black” state. Rise time, Tr, is the time between photo detector output intensity changedfrom90﹪to 10﹪. And fall time, Tf, is the time between photo detector output intensity changed from10﹪to 90﹪.Note 4: Definition of contrast ratio:The contrast ratio is defined as the following expression.Luminance measured when LCD on the “White” stateContrast ratio (CR)=Luminance measured when LCD on the “Black” stateNote 5: White Vi = V i50 ± 1.5V Black Vi = V i50 ± 2.0V“±” means that the analog input signal swings in phase with VCOM signal.PreliminaryThe 100% transmission is defined as the transmission of LCD panel when all the input terminals of module are electrically opened.Note 6: Definition of color chromaticity (CIE 1931)Color coordinates measured at the center point of LCDNote 7: Measured at the center area of the panel when all the input terminals of LCD panel are electrically opened.Preliminary9. INTERFACE9.1. LCM PIN DefinitionPin Symbol I/O Function Remark1 NC - NC2 NC - NC3 NC - NC4 NC - NC5 NC - NC6 GND I Power Ground7 EDGSL I Define Input Clock Polarity.When EDGSL=L, Latch Data By Rising Edge of CLK. ( Default Pull Low)When EDGSL=H, CLK Polarity is Inverted, Latch Data by Falling Edge of CLK.8 VCC I Digital Power Supply (+3.3V)9 V9 I Gamma voltage level 910 VGL I Gate OFF power supply voltage11 V2 I Gamma voltage level 212 VGH I Gate ON power supply voltage13 V6 I Gamma voltage level 614 RESETB I Hardware Global Reset. Low Active. (Default Pull high)15 VCOM I Common electrode voltage input16 GND I Power Ground17 AVDD I Analog Power Supply18 NC - NC19 NC - NC20 V8 I Gamma voltage level 821 V5 I Gamma voltage level 522 V3 I Gamma voltage level 323 GND I Power ground24 R5 I Red data (MSB)25 R4 I Red data26 R3 I Red data27 R2 I Red data28 R1 I Red data29 R0 I Red data (LSB)Preliminary 30 GND I Powerground31 GND I Powerground32 G5 IGreendata(MSB)33 G4 IGreendata34 G3 IGreendata35 G2 IGreendata36 G1 IGreendata37 G0 IGreendata(LSB)38 DE IInput Data Enable Control.When DE Mode. Active High To Enable Data Input. (Default Pull Low)39 NC -NC40 GND I Powerground41 DCLK IClock Signal Input.When CLK=H, User Can Input Different Polarity CLK By EDGSL Setting.When CLK=L, User Can Select CLK Rising Or Dual Edge To Latch By EDGSLSetting.42 VCC I Digital Power Supply (+3.3V)43 NC -NC44 NC -NC45 B5 IBluedata(MSB)46 B4 IBluedata47 B3 IBluedata48 B2 IBluedata49 B1 IBluedata50 B0 IBluedata(LSB)51 NC INC52 V1 I Gamma voltage level 153 V4 I Gamma voltage level 454 V7 I Gamma voltage level 755 V10 I Gamma voltage level 1056 NC -NC57 NC -NC58 AVDD I Analog Power Supply59 GND I Powerground60 VCOM I Common electrode voltage inputPreliminary10. BLOCK DIAGRAM11. QUALITY ASSURANCE***** T a = Ambient TemperatureNote1: The test samples have recovery time for 2 hours at room temperature before thefunction check. In the standard conditions, there is no display function NG issueoccurred.Note2: All the cosmetic specifications are judged before the reliability stress.No. Test Items Test Condition REMARK1 High Temperature Storage Test Ta=80 Dry 240h ℃2 Low Temperature Storage Test Ta=-20 Dry 240h ℃3 High Temperature Operation Test Ta=70 Dry 240h ℃4 Low Temperature Operation Test Ta=-10 Dry 240h ℃5 High Temperature and High HumidityOperation Test Ta=60 90%RH 240h ℃6 Electro Static Discharge Test 150pF, 330Ω, ±8KV(Contact)/±15KV(Air), 5 points/panel, 5 times/pointNon-operation7 Thermal Shock Test -10(0.5h) ~ ℃70(0.5h) / 100℃cycles(Dry)8 Vibration Test Sine wave, 10 ~ 500 ~ 10Hz,1.5G, 0.37oct/min 3 axis, 1hour/axisNon-operation9 Mechanical Shock Test Half sine wave, 180G, 2msone shock of each six faces(I.e. run 180G 2ms for all six faces)Non-operation1st ~ 60thPreliminary12. OUTLINE DRAWINGPreliminaryPreliminary13. PACKAGE INFORMATIONPreliminary14. PRECAUTIONSPlease pay attention to the following when you use this TFT LCD panel with IC and FPC14.1 MOUNTING PRECAUTIONS(1) You must mount a module using arranged in four corners or four sides.(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is notapplied to the module.And the case on which a module is mounted should have sufficient strength so that externalforce is not transmitted directly to the module.(3) Please attach a transparent protective plate to the surface in order to protect the polarizer.Transparent protective plate should have sufficient strength in order to the resist externalforce.(4) You should adopt radiation structure to satisfy the temperature specification.(5) Acetic acid type and chlorine type materials for the cover case are not describe becausethe former generates corrosive gas of attacking the polarizer at high temperature and thelatter causes circuit break by electro-chemical reaction.(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harderthan HB pencil lead. And please do not rub with dust clothes with chemical treatment.Do not touch the surface of polarizer for bare hand or greasy cloth. (Some cosmetics aredetermined to the polarizer)(7) When the surface becomes dusty, please wipe gently with adsorbent cotton or other softmaterials like chamois soaks with petroleum benzene. Normal-hexane is recommendedfor cleaning the adhesives used to attach front / rear polarizers. Do not use acetone,toluene and alcohol because they cause chemical damage to the polarizer.(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizercauses deformations and color fading.(9) Do not open the case because inside circuits do not have sufficient strength.14.2 OPERATING PRECAUTIONS(1) The spike noise causes the mis-operation of circuits. It should be lower than followingvoltage ：V=±200mV(Over and under shoot voltage)(2) Response time depends on the temperature. (In lower temperature, it becomes longer.)(3) Brightness depends on the temperature. (In lower temperature, it becomes lower)And in lower temperature, response time (required time that brightness is stable afterturned on) becomes longer.(4) Be careful for condensation at sudden temperature change. Condensation makes damageto polarizer or electrical contacted parts. And after fading condensation, smear or spot willoccur.(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.(6) Module has high frequency circuits. Sufficient suppression to the electromagneticinterference shall be done by system manufacturers. Grounding and shielding methodsmay be important to minimize the interference.14.3 ELECTROSTATIC DISCHARGE CONTROLSince a module is composed of electronic circuits, it is not strong to electrostatic discharge.Make certain that treatment persons are connected to ground through wristband etc. Anddon’t touch interface pin directly.14.4 PRECAUTIONS FOR STRONG LIGHT EXPOSUREStrong light exposure causes degradation of polarizer and color filter.14.5 STORAGEWhen storing modules as spares for a long time, the following precautions are necessary.(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. KeepPreliminary the temperature between 5 and 35 at normal humidity.℃℃(2) The polarizer surface should not come in contact with any other object. It is recommendedthat they be stored in the container in which they were shipped.14.6 HANDLING PRECAUTIONS FOR PROTECTION FILM(1) When the protection film is peeled off, static electricity is generated between the film andpolarizer. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc.(2) The protection film is attached to the polarizer with a small amount of glue. Is apt to remainon the polarizer. Please carefully peel off the protection film without rubbing it against the polarizer.(3) When the module with protection film attached is stored for a long time, sometimes thereremains a very small amount of glue still on the polarizer after the protection film is peeled off.(4) You can remove the glue easily. When the glue remains on the polarizer surface or itsvestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane.。
