SPL 690说明书_V1.0

Application Note690+ Regen Unit & Active Front EndAPP-AC-04 For 690+ series drives version 5.3g or laterIntroductionOn occasion, one or more drives in a system may absorb power from the machine and pump it back into the drive. This condition is called regeneration. This occurs when motors are being “overhauled” (mechanically pulled at a speed faster than their setpoint) or when the drive and motor are “holding back” their speed to provide desired tension, as in the case of unwind stands. This regenerative energy can be absorbed by other motoring drives if the drives are connected in a common DC bus configuration. The AFE-xxx may be used as an active front end to power the common bus and to regenerate any energy back into the lines. It can also be used as a line regen unit that only regenerates excess energy back into the lines.Used as an Active Front End, the AFE acts as a 4 quadrant power supply to one or more drives. It draws nearly pure sine wave currents at unity power factor with very low harmonic contentUsing the 690+ as a 4-Quadrant power supply in common Bus schemes provides:•Simplified approach to common bus systems•Allows the AFE panel to act as 4-Quadrant DC bus power supply unit•Near-sinusoidal supply currents (Motoring and Regenerating)•Near-unity power factor operation (0.99 or better)•Low supply harmonics currents•eliminates the need for line reactors and circuit breakers for each sectionin the systemIMPORTANT:If drives connected to the 4-Quadrant Regen common DC Bus are beingcontrolled in Volts/Hz motor control mode, it is essential that theVOLTAGE MODE parameter in the VOLTAGE CONTROL function block isset to FIXED. This will ensure the motor is not over fluxed by the boosted720V DC Bus. Failure to do this may lead to motor overheating andpossible burn out.Note:If the drive is part of a common bus system set the ENABLE parameter inthe SLEW RATE LIMIT function block to FALSE.Single Motor SystemThe simplest configuration for 4-Quadrant Regen control is a single AFE-xxx acting as the unity power factor supply, connected via the DC bus to another 690+ driving the motor.SupplyThe AFE panel and the 690+ drive are matched in power, with the AFE supplying the fullmotoring and regenerating requirement of the load. No extra hardware is required to detect the rotation, frequency and phase of the mains supply. Also, no dynamic braking resistor is required. When mains power is applied to the AFE, the DC bus slowly charges through the pre-chargecircuit. The AFE's internal power supply will start in the normal way. When the AFE is healthy and the run (coast stop) signal is applied, synchronization to the mains supply (phase, rotation and frequency) begins. This process takes approximately 100ms. Once synchronized, the DC bus on the common bus is boosted to 720V (on a 460V product). This high value of DC link volts is required for successful regen operation.Applications of single motor 4-Quadrant Regen systems include :• Hoists and Elevators • Dynamometer test rigs • Unwind Stands• Installations that would otherwise require a Harmonic Power FilterMulti-Motor SystemIn many applications, the total power consumed by the system is less than the installed power of the drives. This is because some drives are motoring (rewinds) and some are regenerating(unwinds). In these situations it is efficient to connect the drives on a common DC bus. The AFE panel simplifies the connection of common bus applications as shown below.The 4-Q Regen drive draws sinusoidal, unity power factor current from the supply and only has tobe rated for the net power consumed by the system or by the system braking requirements.Dynamic Braking (e.g. for Emergency Stopping purposes) can still be used in this control mode if required.Feeding the 690+ drives exclusively from the AFE eliminates the need for line reactors and circuit breakers for each section in the system.SupplyBrake ModeThe AFE can also be used as a Line Regen unit. This is selectable in software by setting theBRAKE MODE parameter in the REGEN CONTROL function block toTRUE. In this mode, the AFE is connected onto a common bus. Thedrives on the common bus are supplied via their own 3-phase supplies.The AFE tracks the mains supply but does not supply motoring power tothe common bus. During regeneration, the DC bus will rise and trigger theAFE to return the excess power to the mains in the form of sinusoidalcurrent at unity power factor. Thus, the AFE acts as a smart, no loss,dynamic brake. Since the AFE is not supplying power to the common bus,this mode allows the use of a much smaller AFE unit, sized only for theamount of regenerative energy expected. In this mode, an isolation transformer is required to supply power to the AFE panel and provide isolation from the line drives.In the Brake Mode, each drive, including the AFE, is responsible for pre-charging its own DC bus. When an individual drive is pre-charged and healthy, it connects itself on to the common bus via a DC contactor. Drives disconnect from the common bus under fault conditions or loss of power.M M I M e n u M a p 1 S E T U P 2 M O T O R C O N T R O L 3 R E G E N C N T R O L B R A K E M O D E3-Phase SupplyOrdering the ProductThe AFE is available as an assembly, rated by HP at 460V. (AFE-xxx-LCL). For 230V ratings, consult the factory. Each panel or enclosure contains a 690+ drive configured for use as an active front end, along with the pre-charge resistor, contactor, and the LCL filter.IMPORTANT: Every 690+ drive used as and with an AFE-xxx needs to be ordered with option007. Please append the catalog number with /007. Example: To use a 460V 20HP drive with a AFE-xxx, order catalog number 690+0020/460/1BN/007Software Function BlockRefer to the 690+ Software Manual, Chapter 1 for details on the function block parameters.The AFE is factory configured to be an active front end and the configuration is stored as Macro 8 inside the drive, in case it needs to be restored to the “as-shipped” values. Refer to the product manual for details on restoring macros.HP Amps Catalog # Dimensions 13 12 AFE-13-LCL 22 x 18 26 25 AFE-26-LCL 28 x 22 45 45 AFE-45-LCL 33 x 27 85 80 AFE-85-LCL 46 x 34125 120 AFE-125-LCL 46 x 34 167 160 AFE-167-LCL 46 x 34 200 194 AFE-200-LCL 79 x 47 x 24 300 284 AFE-300-LCL 79 x 47 x 24 350 325 AFE-350-LCL 79 x 47 x 24 400 378 AFE-400-LCL 79 x 47 x 24 500468AFE-500-LCL79 x 47 x 24Open panelEnclosedControl ConnectionsSetupAlthough most parameters will be preset to the correct values, follow the steps below to set up for your applicationIn the Quick Setup menu:• Control Mode should be set to 4-Q REGEN• Leakage inductance should be set to the value of total line reactor inductance in mH.HP Amps Catalog # Leakage Inductance 13 12 AFE-13-LCL 6 mH 26 25 AFE-26-LCL 2.9 mH 45 45 AFE-45-LCL 1.64 mH 85 80 AFE-85-LCL 0.93 mH 125 120 AFE-125-LCL0.55 mH 167 160 AFE-167-LCL 0.41 mH 200 194 AFE-200-LCL 0.33 mH 300 284 AFE-300-LCL 0.225 mH 350 325 AFE-350-LCL0.205 mH 400 378 AFE-400-LCL 0.17 mH 500468AFE-500-LCL0.14 mH• In the Regen Control menu: (Setup/Motor Control/Regen Control), set Brake Mode = FALSE for active front end, or TRUE for line regen mode.220V AC 3A maximum TB3TB1TB2into a resistive load (default)1234567891011O U T 1_A O U T 1_B O U T 2_A O U T 2_B O U T 3_A O U T 3_B23242526A I N 1A I N 2A I N 3A O U T 3A I N 4A O U T 1A O U T 2+10V R E F 0V -10V R E F+24V C0V D I N 1 (P R E -C H A R G E C L O S E D )D I N 2 (N O T C O A S T S T O P )D I N 3D I N 4D I N 5D I N 6D I N 7 (R E M O T E T R I P R E S E T )I N 8 (E X T T R I P )RUNNINGCLOSE PRE-CHARGEMacro 8 provides the following connections:•Digital Output 3 (terminals 25 & 26) controls the external pre-charge circuit.•Digital input 1 (terminal 12) is used to confirm the status of the pre-charge circuit (open or closed). The AFE will not synchronize with the 3-phase power unless the pre-chargecontactor is closed.•Digital input 2 (terminal 13) is used to run the AFE.•Upon the introduction of the run command, the drive automatically synchronizes to the 3-phase power if the pre-charge contactor has closed.•Digital input 2 (terminal 13) may be connected to 24V, or used to cause a coast stop in caseof emergencies.。

690Power Fishing System52064014 REV 3© 2019 Greenlee Tools, Inc.2/19Register this product at 690 Power Fishing SystemGreenlee Tools, Inc.4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-70702DescriptionThe Greenlee 690 Power Fishing System is intended to “fish,” or route, nylon fishing line through 1/2" to 4" conduit. Optional accessories are also a vailable for fishing through 5" and 6" conduit, and for clean-up vacuuming.This tool is intended for commercial use.SafetySafety is essential in the use and maintenance ofGreenlee tools and equipment. This instruction manual and any markings on the tool provide information for avoiding hazards and unsafe practices related to the use of this tool. Observe all of the safety information provided.Purpose of this ManualThis manual is intended to familiarize personnel with the safe operation and maintenance procedures for theG reenlee 690 Power Fishing System.Keep this manual available to all personnel.Replacement manuals are available upon request at no charge at .Do not discard this product or throw away!For recycling information, go to .All specifications are nominal and may change as designimprovements occur. Greenlee Tools, Inc. shall not be liable for damages resulting from misapplication or misuse of its products.Mighty Mouser is a registered trademark of Greenlee Tools, Inc.KEEP THIS MANUALTable of ContentsDescription ....................................................................2Safety ............................................................................2Purpose of this Manual .................................................2Important Safety Information .....................................3–4Grounding Instructions ..................................................4Identification ..................................................................5Specifications ................................................................5Assembly .......................................................................6Operation ....................................................................6–8Maintenance ...............................................................8–9Troubleshooting .............................................................9Illustration ....................................................................10Parts List .....................................................................11Wiring Diagram (12)690 Power Fishing SystemGreenlee Tools, Inc.4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-70703IMPORTANT SAFETY INFORMATIONSAVE THESE INSTRUCTIONS690 Power Fishing SystemGreenlee Tools, Inc.4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-70704IMPORTANT SAFETY INFORMATIONNote: Keep all decals clean and legible, and replace when necessary.SAVE THESE INSTRUCTIONSGrounding InstructionsThis tool must be grounded. In the event of a malfunc-tion or breakdown, an electrical ground provides a path of least resistance for the electric current. This path of least resistance is intended to reduce the risk of electric shock.This tool’s electric cord has a grounding conductor and a grounding plug as shown. Do not modify the plug. Connect the plug to a corresponding GFCI-protected receptacle that is properly installed and grounded in accordance with all national and local codes and ordinances.Do not use an adapter.NEMA 5-15ReceptaclePlug690 Power Fishing SystemGreenlee Tools, Inc.4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-70705IdentificationIntake Port (for vacuuming)Exhaust Port (for blowing)SpecificationsMotor ....................................................................................12 amps / 12 VAC / 60 Hz PressureBlower ............................................................................................. 4 psi (0.275 bar)VacuumColumn of Water .............................................................................112.8" (2.9 m)Column of Mercury .........................................................................8.3" (211 mm)Air Flow .......................................................................................120 CFM (3.4 m 3/min)Tank Capacity (liquid) ..........................................................................12 U.S. gal (41 l)Mass / Weight .............................................................................................52 lb (24 kg)690 Power Fishing SystemGreenlee Tools, Inc.4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-70706AssemblyRefer to the “Illustration” and “Parts List” sections of this manual.1. Attach the handle to the tank by using four screws(44) and four washers (43). Make sure to leave enough space for the storage box. DO NOT screw the screws tight.43442. Attach the storage box to the tank by position-ing the box over the screws and washers from the handle and sliding the box down firmly until it locks into place. If preferred, tighten the screws to squeeze the storage box. Be careful NOT toovertighten.3. Attach the storage box lid to the handle by usingtwo shoulder screws (47) and two nuts (48).4748OperationUse the 690 alone, or combine it with a 592 Mighty Mouser ® Blow Gun Kit as shown here.OPERATING TIPS• When fishing through IMC or rigid, blowing isg enerally more efficient than vacuuming.• When fishing through EMT, vacuuming is the better method. EMT connections are not airtight, and a piston that is blown through might not reach the exit end of the conduit run.• Two fishing lines can be vacuumed in at the same time, if desired. Leave one line in the conduit to pull additional wire into the conduit after the initial i nstallation.690 Power Fishing SystemGreenlee Tools, Inc.4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-70707Operation (cont’d)VACUUMINGBLOWING WITH OPTIONAL 592 MIGHTY MOUSER ® BLOW GUN KITBLOWING690 Power Fishing SystemGreenlee Tools, Inc.4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-70708Operation (cont’d)CLEAN-UP VACUUMINGWet PickupThis unit is equipped with a shut-off float valve. When the unit is used for wet pickup, the rising fluid lifts the float valve until it seals against the motor intake. When this happens, the sound of the motor changes to a higher pitch. Unplug the unit, empty the tank, and replace the cover.Dry PickupFor optional dry pickup accessories, refer to “Optional Equipment” at the end of the Parts List.MaintenanceNote: Keep filters clean. Efficiency of this vacuum is largely dependent on the cleanliness of the filters. A clogged filter can cause overheating and damage to the motor. Filters should be removed and cleaned periodi-cally to ensure proper operation. After cleaning, allow filters to dry thoroughly to prevent deterioration.FILTERS AND GASKETS 1. Unplug the unit2. Remove the tank cover.3. Unscrew three nuts from filter (located under thefilter).4. Clean the filters by spraying with water. Allow themto dry thoroughly.5. Install the filters. Install the tank cover and securewith the catches.690 Power Fishing SystemGreenlee Tools, Inc.4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-70709TroubleshootingProblemProbable Cause Probable Remedy Unit does not run.Faulty cord.Replace cord.Faulty switch.Replace switch.Faulty motor.Replace motor.Unit does not develop adequate vacuuming or blowing pressure.Filters are dirty.Clean the filters. Refer to the “Maintenance” section of this manual.Gaskets do not seal well.Replace gaskets. Refer to the “Maintenance” section of this manual.Tank is full.Empty the tank.Piston does not travel through the conduit.Wrong piston size.Select the correct piston size.Conduit run is obstructed.Clear the conduit run. Check for fl attened bends.EMT couplings are loose.Tighten the couplings.Maintenance (cont’d)CLEANING AND STORAGEPeriodically wipe the outside of the tank with a damp cloth and mild detergent; do not use abrasives or solvents.When not in use, store the 690 indoors in a cool, dry environment. Wrap the power cord loosely around the motor cover.690 Power Fishing SystemGreenlee Tools, Inc.4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-707010Illustration59585756556053543033323134384742464443484538373639404150–5214127831516561819212091110232221690-RMReplacement Motor Kit(includes 1–23)690-RT Replacement Tank Kit (includes 30–48)1741349690 Power Fishing SystemGreenlee Tools, Inc.4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-707011Parts List690-RM Replacement motor kit— fits previous 690 model (includes 1–23) 1 Cover, motor .........................................1 2 Bolt,1/4-20 x 2.50 .................................3 3 Baffle, air ...............................................1 4 Tie, cable ..............................................1 5 Motor, electric 115 V .............................1 6 Gasket, blower ......................................1 7 Plate, switch .........................................1 8 Screw, slftpg, #8-18 x .375 Phil pan hd ............................................4 9 Screw, machine #8-32 x .500 rd hd ................................1 10 Washer, lock, .172 x .332 x .020 int T .........................2 11 Nut, hex, #8-32 .....................................2 12 Washer, lock, .593 x .472 int .................1 13 Ring, locking .........................................1 14 Switch, toggle .......................................1 15 Cord, electric, 14 ga x 76" SJOW ................................1 16 Connector, strain relief ..........................1 17 Nut, 1/2 conduit lock ............................1 18 Cover, tank ............................................1 19 Gasket, tank cover ................................1 20 Filter ......................................................1 21 Ball, rubber, 2.50 dia. ............................1 22 Washer, flat, .250 x .562 x .048 ZP #10 ..................................................3 23 Nut, hex, 1/4-20 Nylok ..........................3 690-RT Replacement tank kit— fits previous 690 model (includes 30–48) 30 Tank.......................................................1 31 Screw, machine #12-24 x .625 rd hd ..............................6 32 Washer, lock, .225 x .377 x .056 spr zinc .................................................6 33 Catch, toggle, Nielsen #HC801ZE ........3 34 Washer, flat, .656 x 1.312 x .095 bk-ox .....................................................2 35 Caster, swivel, 3.00 x .812 ....................2 36 Bracket, axle .........................................1 37 Screw, 1/4-20 x .62 pan hd ..................4 38 Washer, lock, .259 x .489 x .062 spr ...........................4 39 Axle, vacuum tank .750 x 16.03 (1)40 Wheel, 8 x 2.5 3/4 rlr brg (2)41 Ring, retaining .750 Truarc #5100 ex ...............................................2 42 Handle ...................................................1 43 Washer, flat .32 x .57 x .06 cad pl .......10 44 Screw, 1/4-20 x 1.75 btn hd cap ..........4 45 Box unit, storage...................................1 46 Lid, storage ...........................................1 47 Screw, 5/16 x 1.5 shoulder ...................2 48 Nut, lock-hex, 1/4-20 ............................249 Washer, Flat, .81 x 1.5 x .14 ..................3 50 RH10 Hose, vacuum, 10' w/cuffs ...................1 51 RH15 Hose, vacuum, 15' w/cuffs ...................1 52 RH25 Hose, vacuum, 25' w/cuffs ...................1 53 Cuff .......................................................2 54 595 Nylon line, 85 lb tensile-strength, length of 2150 ft ....................................1 55 50256467 Adapter cone, 1/2" through 1" ..............1 56 50256440 Adapter cone, 1-1/4 through 2-1/2" .....1 57 50256459 Adapter cone, 3" through 4" .................1 58 50233602 Fish line adapter, blowing .....................1 59 608 Piston for 1/2" conduit, foam type ........1 609 Piston for 3/4" conduit, foam type ........1 610 Piston for 1" conduit, foam type ...........1 611 Piston for 1-1/4" conduit, foam type ....1 612 Piston for 1-1/2" conduit, foam type ....1 613 Piston for 2" conduit, foam type ...........1 614 Piston for 2-1/2" conduit, foam type ....1 615 Piston for 3" conduit, foam type ...........1 616 Piston for 3-1/2" conduit, foam type ....1 617 Piston for 4" conduit, foam type ...........1 621 Piston for 2-1/2" EMT ...........................1 646 Piston for 3-1/2" EMT ...........................1 622 Piston for 3" EMT . (1)623Piston for 4" EMT (1)60 50341189 Warning card .........................................1Optional Accessories 70 691 Mighty Mouser ® blow gun ....................1 71 430 Poly line bucket, 6500' .........................1 72 435 Conduit measuring tape, 3/16" x 3000' . (1)K eyPart No.DescriptionQtyK eyPart No.DescriptionQty690 Power Fishing System Wiring Diagram4455 Boeing Drive • Rockford, IL 61109-2988 • USA • 815-397-7070©2019 Greenlee Tools, Inc. • An ISO 9001 Company USA Tel: 800-435-0786Fax: 800-451-2632Canada Tel: 800-435-0786Fax: 800-524-2853International Tel: +1-815-397-7070Fax: +1-815-397-9247。

Dell Precision™ Workstation 690 Quick Reference GuideModel DCD0w w w.d e l l.c o m|s u p p o r t.d e l l.c o mNotes, Notices, and CautionsNOTE: A NOTE indicates important information that helps you make better use of your computer.NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoidthe problem.CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.Abbreviations and AcronymsFor a complete list of abbreviations and acronyms, see Glossary in your User’s Guide.If you purchased a Dell™ n Series computer, any references in this document to Microsoft® Windows®operating systems are not applicable.____________________Information in this document is subject to change without notice.©2006Dell Inc.All rights reserved.Reproduction in any manner whatsoever without the written permission of Dell Inc.is strictly forbidden.Trademarks used in this text: Dell, the DELL logo and Dell Precision are trademarks of Dell Inc.; Intel, Xeon, and Pentium are registered trademarks of Intel Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation.Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.Model DCD0January 2006P/N JD964Rev. A00ContentsFinding Information (5)Setting Up Your Computer (9)About Your Computer (14)Front View (15)Back View (18)Back Panel Connectors (19)Inside View (21)System Board Components (22)Locating Your User’s Guide (24)Removing the Computer Cover (24)Computer Stand (27)Attaching the Computer Stand (27)Removing the Computer Stand (29)Caring for Your Computer (29)Solving Problems (29)Troubleshooting Tips (29)Resolving Software and Hardware Incompatibilities (30)Using Microsoft® Windows® XP System Restore (30)Using the Last Known Good Configuration (31)Dell Diagnostics (32)Before you start testing (33)Beep Codes (33)Error Messages (35)Diagnostic Lights (35)Diagnostic Light Codes Before POST (35)Diagnostic Light Codes During POST (37)Frequently Asked Questions (42)Index (43)Contents34ContentsFinding InformationNOTE: Some features or media may be optional and may not ship with your computer. Some features or media may not be available in certain countries.NOTE: Additional information may ship with your computer.What Are You Looking For?Find It Here•A diagnostic program for my computer •Drivers for my computer•My computer documentation•My device documentation •Desktop System Software (DSS)Drivers and Utilities CD (also known as Resource CD)Documentation anddrivers are alreadyinstalled on yourcomputer. Y ou can usethe CD to reinstall drivers,run the Dell Diagnosticsor access yourdocumentation. Readmefiles may be included onyour CD to provide last-minute updates about technical changes to your computer or advanced technical-reference material for technicians or experienced users. NOTE: Drivers and documentation updates can be foundat .•How to set up my computer •How to care for my computer •Basic troubleshooting information •How to run the Dell™ Diagnostics •Error codes and diagnostic lights •How to remove and install parts •How to open my computer coverQuick Reference GuideNOTE: This document is available as a PDF at .Quick Reference Guide5•Warranty information•Terms and Conditions (U.S. only)•Safety instructions•Regulatory information•Ergonomics information•End User License AgreementDell™ Product Information Guide•How to remove and replace parts •Specifications•How to configure system settings •How to troubleshoot and solve problems User’s GuideMicrosoft®Windows®XP Help and Support Center1Click the Start button and click Help and Support 2Click User’s and system guides and click User’s Guide The User’s Guide is also available on the Drivers and Utilities CD.•Service Tag and Express Service Code •Microsoft Windows License Label Service Tag and Microsoft® Windows® LicenseThese labels are located on your computer.•Use the Service Tag toidentify your computerwhen you use orcontact technicalsupport.•Enter the ExpressService Code to direct your call when contacting technical support.What Are You Looking For?Find It Here6Quick Reference Guide•Solutions — Troubleshooting hints and tips, articles from technicians, and online courses, frequently asked questions•Community — Online discussion with other Dell customers•Upgrades — Upgrade information for components, such as memory, the hard drive, and the operating system•Customer Care — Contact information, service call and order status, warranty, and repair information •Service and support — Service call status and support history, service contract, online discussions with technical support•Reference — Computer documentation, details on my computer configuration, product specifications, and white papers•Downloads — Certified drivers, patches, and software updates•Desktop System Software (DSS)— If you reinstall the operating system for your computer, you should reinstall the DSS utility prior to installing any of the drivers. DSS provides critical updates for your operating system and support for Dell™ 3.5-inch USB floppy drives, optical drives, and USB devices. DSS is necessary for correct operation of your Dell computer. The software automatically detects your computer and operating system and installs the updates appropriate for your configuration.Dell Support Website — NOTE: Select your region or business segment to viewthe appropriate support site.NOTE: Corporate, government, and education customers can also use the customized Dell Premier support website at . The website may not be available in all regions.•How to use Windows XP•How to work with programs and files •Documentation for devices (such as modem)Windows Help and Support Center1Click the Start button and click Help and Support. 2T ype a word or phrase that describes your problem and click the arrow icon.3Click the topic that describes your problem.4Follow the instructions on the screen.What Are You Looking For?Find It HereQuick Reference Guide7•How to reinstall my operating system Operating System CDThe operating system isalready installed on yourcomputer. To reinstall youroperating system, use theOperating System CD. Seeyour User’s Guide forinstructions. After youreinstall your operatingsystem, use the Drivers andUtilities CD (ResourceCD)to reinstall drivers for thedevices that came with your computer. Y our operatingsystem product key label is located on your computer.NOTE: The color of your CD varies based on the operatingsystem you ordered.NOTE: The Operating System CD may be optional and maynot ship with your computer.•How to use Linux•E-mail discussions with users of Dell Precision™ products and the Linux operating system •Additional information regarding Linuxand my Dell Precision computer Dell Supported Linux Sites••/mailman/listinfo/linux-precisionWhat Are You Looking For?Find It Here8Quick Reference GuideQuick Reference Guide 9Setting Up Your ComputerCAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.Y ou must complete all steps to properly set up your computer.1Connect the keyboard and the mouse.2NOTICE: Do not connect a modem cable to the network adapter. Voltage from telephonecommunications can damage the network adapter.NOTE: connect the network cable to the card.Connect the modem or the network cable.10Quick Reference Guide3Depending on your graphics card, you can connect your monitor in various ways.NOTE: You may need to use the provided adapter or cable to connect your monitor to the computer.Connect the monitor.The dual-monitor cable is color-coded; the blue connector is for the primary monitor, and the black connector is for the second monitor. To enable dual-monitor support, both monitors must be attached to the computer when you start the computer.For single- and dual-monitor capable cards with a single connectorOne VGA adapter:Use the VGA adapter when you have a single-monitorgraphics card and you want to connect your computerto a VGA monitor.Dual VGA Y cable adapter:Use the appropriate Y cable when your graphics card has a single connector and you want to connect your computer to one or two VGA monitors.Dual DVI Y cable adapter:Use the appropriate Y cable when your graphics card has a single connector and you want to connect your computerto one or two DVI monitors.For dual-monitor capable cards with one DVI connector and one VGA connectorFor dual-monitor capable cards with two DVI connectorsT wo DVI connectors:Use the DVI connectors to connectyour computer to one or two DVImonitors.T wo DVI connectors with one VGAadapter:Use the VGA adapter to connect a VGA monitor to one of the DVI connectors on your computer T wo DVI connectors with two VGA adapters:Use two VGA adapters to connect two VGA monitors to the DVI connectors on your computer.4 NOTE: If yourcomputer has a soundcard installed, connectthe speakers to thecard.Before you install any devices or software that did not come with your computer, read the documentation that came with the software or device or contact the vendor to verify that the software or device is compatible with your computer and operating system.Y ou have now completed the setup for your computer.About Your Computer CAUTION:Your computer is heavy (it has an approximate minimum weight of 55 lbs) and can be difficult to maneuver. Seek assistance before attempting to lift, move, or tilt it; this computer requires a two-man lift. Always lift correctly to avoid injury; avoid bending over while lifting. See your Product Information Guide for other important safety information.CAUTION: Before setting your computer upright, install the computer stand. Failure to install the stand before setting the computer upright could cause the computer to tip over, potentially resulting in bodily injury or damage to the computer.6Install additional software or devices.Front View1-3 5.25-inch drive bays Can hold a CD/DVD drive, or a Media Card Reader, floppy drive, or SATA harddrive in a 5.25-inch drive bay carrier.NOTE: The drive carriers are only for use in the 5.25-inch drive bays. Thefloppy-drive/ Media Card Reader and hard-drive carriers are not interchangeable.4 5.25-inch drive bay withspecial 3.5-inch drivepanel plate Can hold a CD/DVD drive, or a Media Card Reader, floppy drive, or SATA hard drive in a 5.25-inch drive bay carrier. The drive-panel plate shown here is only for use with a floppy drive or Media Card Reader; it can be installed in front of any of the four 5.25-inch drive bays. For more information, see your User’s Guide. NOTE: The drive carriers are only for use in the 5.25-inch drive bays. The floppy drive/ Media Card Reader and hard drive carriers are not interchangeable.5hard-drive activity light The hard drive light is on when the computer reads data from or writes data to thehard drive. The light might also be on when a device such as your CD player isoperating.6IEEE 1394 connector Use the IEEE 1394 connector for high-speed data devices such as digital videocameras and external storage devices.7USB 2.0 connectors (2)Use the front USB connectors for devices that you connect occasionally, such asflash memory keys, cameras, or bootable USB devices (see your User’s Guide formore information).It is recommended that you use the back USB connectors for devices that typicallyremain connected, such as printers and keyboards.8power button Press to turn on the computer.NOTICE: To avoid losing data, do not use the power button to turn off thecomputer. Instead, perform an operating system shutdown.NOTE: The power button can also be used to wake the system or to place it intoa power-saving state. See your User’s Guide for more information.9power light The power light illuminates and blinks or remains solid to indicate different states:•No light — The computer is turned off or in a hibernation mode.•Steady green — The computer is in a normal operating state.•Blinking green — The computer is in a power-saving state.•Blinking or solid amber — See "Power Problems" in your User’s Guide.To exit from a power-saving state, press the power button or use the keyboard orthe mouse if it is configured as a wake device in the Windows Device Manager.For more information about sleep states and exiting from a power-saving state,see your User’s Guide.See "Diagnostic Lights" on page35 for a description of light codes that can helpyou troubleshoot problems with your computer.10microphone connector Use the microphone connector to attach a personal computer microphonefor voice or musical input into a sound or telephony program.11headphone connector Use the headphone connector to attach headphones.12network link light The network link light is on when a good connection exists between a 10-Mbps,100-Mbps, or 1000-Mbps (or 1-Gbps) network and the computer.13diagnostic lights (4)Use these lights to help you troubleshoot a computer problem based on thediagnostic code. For more information, see "Diagnostic Lights" on page35.Back View1power connector Insert the power cable. The appearance of this connector may differ from what ispictured here.2card slots Access connectors for any installed PCI, PCI-X, or PCI Express cards.NOTE: The center five connector slots support full-length cards: one PCI, one PCIexpress x16, one PCI express x8 (wired as x4), and two PCI-X slots; the connectorslots at the top and at the bottom support half-length cards: two PCI express x8 slots(wired as x4).3back panel connectors Plug serial, USB, and other devices into the appropriate connector(see "Back Panel Connectors" on page19).Back Panel Connectors1parallel connector Connect a parallel device, such as a printer, to the parallel connector. If you havea USB printer, plug it into a USB connector.NOTE: The integrated parallel connector is automatically disabled if the computerdetects an installed card containing a parallel connector configured to the sameaddress. For more information, see your User’s Guide.2line-out/ headphone connector Use the green line-out connector to attach headphones and most speakers with integrated amplifiers.On computers with a sound card, use the connector on the card.3mouse connector Plug a standard mouse into the green mouse connector. T urn off the computerand any attached devices before you connect a mouse to the computer. If you havea USB mouse, plug it into a USB connector.If your computer is running the Microsoft® Windows® XP operating system,the necessary mouse drivers have been installed on your hard drive.4USB 2.0 connectors (3)It is recommended that you use the front USB connectors for devices that youconnect occasionally, such as flash memory keys, cameras, or bootable USBdevices.Use the back USB connectors for devices that typically remain connected,such as printers and keyboards.5link integrity light•Green — A good connection exists between a 10-Mbps network and thecomputer.•Orange — A good connection exists between a 100-Mbps network and thecomputer.•Yellow — A good connection exists between a 1000-Mbps (or 1-Gbps) networkand the computer.•Off — The computer is not detecting a physical connection to the network.6network adapter connector To attach your computer to a network or broadband device, connect one endof a network cable to either a network jack or your network or broadband device. Connect the other end of the network cable to the network adapter connector on your computer. A click indicates that the network cable has been securely attached.NOTE: Do not plug a telephone cable into the network connector.On computers with an additional network connector card, use the connectors on the card and on the back of the computer when setting up multiple network connections (such as a separate intra- and extranet).It is recommended that you use Category 5 wiring and connectors for your network. If you must use Category 3 wiring, force the network speed to 10 Mbps to ensure reliable operation.7network activity light Flashes a yellow light when the computer is transmitting or receiving networkdata. A high volume of network traffic may make this light appear to be in a steady"on" state.8USB 2.0 connectors (2)It is recommended that you use the front USB connectors for devices that youconnect occasionally, such as flash memory keys, cameras, or bootable USBdevices.Use the back USB connectors for devices that typically remain connected,such as printers and keyboards.9IEEE 1394 connector Use the IEEE 1394 connector for high-speed data devices such as digital videocameras and external storage devices.10keyboard connector If you have a standard keyboard, plug it into the purple keyboard connector.If you have a USB keyboard, plug it into a USB connector.11line-in connector Use the blue line-in connector to attach a record/playback device such as a cassetteplayer, CD player, or VCR.On computers with a sound card, use the connector on the card.12serial connector Connect a serial device, such as a handheld device, to the serial port. If necessary,the address for this port can be modified through System Setup (see your User’sGuide for more information).13serial connector Connect a serial device, such as a handheld device, to the serial port. If necessary,the address for this port can be modified through System Setup (see your User’sGuide for more information).Inside View1power supply 2hard drive bay 3memory shroudNOTICE: The memory shroud holds the (optional) memory riser cards in place; itsthumbscrews must be sufficiently tight in order to secure the risers and to avoid damage.4front fan 5card fan6 5.25-inch drive bay with 3.5-inch drive panel plate 75.25-inch drive baySystem Board Components1secondary processor connector (CPU_1)18FlexBay connector (USB)2front fan connector (FAN_FRONT)19floppy drive (DSKT)3card cage fan connector (FAN_CCAG)20front panel connector (FRONTPANEL) 4internal speaker connector (INT_SPKR)21front panel 1394 connector (FP1394)5power connector (POWER2) 22chassis intrusion header (INTRUDER)6IDE drive connector (IDE)23PCI-Express x8 card slot, wired as x4(SLOT7_PCIE)7password jumper (PSWD)24PCI-X card slot (SLOT6_PCIX)8auxiliary hard-drive LED connector(AUX_LED)25PCI-X card slot (SLOT5_PCIX)9battery socket (BATTERY)26PCI card slot (SLOT4_PCI)NOTE: This slot is not available in the dual-graphics configuration10SATA connectors(SATA_0, SATA_1, SATA_2)27PCI-Express x8 card slot, wired as x4(SLOT3_PCIE)NOTE: In the dual-graphics configuration, this slotis replaced by a x16 slot on the graphics riser.It holds a graphic card.11RTC reset jumper (RTCRST)28PCI-Express x16 card slot (SLOT2_PCIE)NOTE: This slot is not available in the dual-graphics configuration12main power connector (POWER1)29PCI-Express x8 card slot, wired as x4(SLOT1_PCIE)NOTE: In the dual-graphics configuration, this slotis replaced by a x16 slot on the graphics riser. Itholds a graphics card.13hard drive connector (HDD_3)30memory fan connector (FAN_MEM)14hard drive connector (HDD_2)31white memory module connectors (DIMM_1-4)support memory modules or memory modulerisers15hard drive connector (HDD_1)32black memory module connectors (DIMM_5-8)support memory modules only when no memoryriser cards are installed; otherwise these must beleft empty16hard drive connector (HDD_0)33primary processor connector (CPU_0)17hard drive fan (FAN_HDD)Cable Colors Locating Your User’s GuideY our User’s Guide contains additional information about your computer such as:•Technical specifications•Front and back views of your computer, including all of the available connectors•Inside views of your computer, including a detailed graphic of the system board and the connectors •Instructions for cleaning your computer•Information on software features, such as Legacy Select Technology control, using a password, and system setup options•Tips and information for using the Microsoft Windows XP operating system•Instructions for removing and installing parts, including memory, cards, drives, the microprocessor, and the battery•Information for troubleshooting various computer problems •Instructions for using the Dell Diagnostics and reinstalling drivers •Information on how to contact DellY ou can access the User’s Guide from your hard drive or the Dell Support website at .Removing the Computer CoverCAUTION:Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.CAUTION:To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover.CAUTION: Your computer is heavy (it has an approximate minimum weight of 55 lbs) and can be difficult tomaneuver. Seek assistance before attempting to lift, move, or tilt it; this computer requires a two-man lift. Always lift correctly to avoid injury; avoid bending over while lifting. See your Product Information Guide for other important safety information.CAUTION: The computer stand should be installed at all times to ensure maximum system stability. Failure to install the stand could result in the computer tipping over, potentially resulting in bodily injury or damage to the computer.DeviceColor Hard drive (with on-board controller)blue cable Floppy drive black pull-tab CD/DVD driveorange pull-tabNOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer’s electronic components. You can do so by touching an unpainted metal surface on the computer.1Follow the procedures in "Before Y ou Begin" in the User’s Guide.NOTICE: Opening the computer cover while the computer is running could result in a shutdown without warning and a loss of data in open programs. The computer cooling system cannot function properly while the cover is removed.2If you have installed a security cable, remove it from the security cable slot.3Carefully, with the help of an assistant, remove the computer stand (see "Removing the Computer Stand").CAUTION: Your computer is heavy (it has an approximate minimum weight of 55 lbs) and can be difficult to maneuver. Seek assistance before attempting to lift, move, or tilt it; this computer requires a two-man lift. Always lift correctly to avoid injury; avoid bending over while lifting. See your Product Information Guide for other important safety information.CAUTION: The computer stand should be installed at all times to ensure maximum system stability. Failure to install the stand could result in the computer tipping over, potentially resulting in bodily injury or damage to the computer.NOTICE: Ensure that you are working on a level, protected surface to avoid scratching either the computer or the surface on which it is resting.4Carefully, with the help of an assistant, lower your computer down to a flat surface with the cover facing up.5Pull back the cover latch release.NOTICE: Ensure that sufficient space exists to support the removed cover—at least 30 cm (1 ft) of desk top space.1cover latch release2computer cover3cover hinges6Locate the three hinge tabs on the edge of the computer.7Grip the sides of the computer cover and pivot the cover up, using the hinges as leverage points. 8Release the cover from the hinge tabs and set it aside in a secure location.NOTICE: The computer cooling system cannot function properly while the computer cover is not installed.Do not attempt to boot the computer before reinstalling the computer cover.Computer StandCAUTION: Your computer is heavy (it has an approximate minimum weight of 55 lbs) and can be difficult to maneuver. Seek assistance before attempting to lift, move, or tilt it; this computer requires a two-man lift. Always lift correctly to avoid injury; avoid bending over while lifting. See your Product Information Guide for otherimportant safety information.CAUTION: The computer stand should be installed at all times to ensure maximum system stability. Failure to install the stand could result in the computer tipping over, potentially resulting in bodily injury or damage to the computer.CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover.NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer’s electronic components. You can do so by touching an unpainted metal surface on the computer.Attaching the Computer StandCAUTION: Your computer is heavy (it has an approximate minimum weight of 55 lbs) and can be difficult to maneuver. Seek assistance before attempting to lift, move, or tilt it; this computer requires a two-man lift. Always lift correctly to avoid injury; avoid bending over while lifting. See your Product Information Guide for otherimportant safety information.CAUTION: The computer stand should be installed at all times to ensure maximum system stability. Failure to install the stand could result in the computer tipping over, potentially resulting in bodily injury or damage to the computer.1Follow the procedures in "Before Y ou Begin" in the User’s Guide.2If you have installed a security cable, remove it from the security cable slot.3Set the stand on the ground in front of the computer, so that the front and the back of the stand touch the ground.If the front and the back of the stand point up toward the ceiling, the stand is upside down.4Ensure that the alignment guide faces the computer.If the alignment guide points away from the computer, the stand is backwards.5Align the center of the stand with the center of the computer.6Carefully, with the help of an assistant, tilt the computer backwards slightly- just high enough to slide the stand beneath it.7Slide the rear of the stand into the rear foot of the computer, and ensure that the alignment guide slides into place.8Center the front bar of the stand in the corresponding notch in the front foot of the computer.9Carefully set the computer back down; the front bar of the stand should snap into place under the weight of the computer.1computer 2computer stand 3alignment guide。

操作手册艾默生管道工具（上海）有限公司目录安全须知 (2)描述、规格及标准配置描述 (3)规格 (3)附件 (3)操作说明 (3)维修说明 (4)终身质保条款........................................................................................................................封底安全须知警告！请仔细阅读所有的安全注意事项和安全指导。

如果不遵从这些安全指导可能会导致电击、火灾或者严重人身伤害。

请妥善保存本安全注意事项和安全指导。

工作场所安全注意事项1. 保持工作场所干净整洁和照明充分。

混乱和昏暗的环境容易引起安全事故的发生。

2. 不要在易燃易爆等的危险环境下操作电动工具，例如易燃易爆的液体、气体或粉尘环境下。

电动工具可能会产生火花，会引燃这些粉尘或气体。

3. 在操作机器时，使无关人员（包括小孩、旁观者、非工作人员等）远离工作现场。

不相关的干扰会影响你对工具的正确使用。

用电安全1. 电动工具插头应该和插座相匹配。

任何时候都不要改变插头。

不要连接插有接地的电动工具的插头的适配器一起使用。

不改变插头和与插座相匹配将会减少电击事故的发生。

2. 避免身体与接地物体的表面接触，如金属管道、散热器、金属柜体和制冷设备。

如果身体和接地物体接触，会增加电击危险的机率。

3. 不要把电动工具防置于雨中或潮湿的环境下。

水进入电动工具将增加电击危险的发生。

4. 不要损坏电源线。

不要把电源线用来拖、拽电动工具。

使电源线远离热、油、尖锐边缘或移动物体。

电源线损坏或卷入其它物体中都会增加电击危险。

5. 当在室外使用电动工具时，请使用适合在室外工作的接线板，例如标记有“W-A”或“W”符号的接线板。

6. 仅限于使用有三股线的三头插头和三孔插座。

如果使用其他类型的，那么有可能没有接地而增加了电击的危险。

7. 请参照下表选择电线，如果尺寸不对，那么会引起较大的压降和电力损失。

恭喜您购买此款功能先进的 LG KF690 手机，它采用了最新的数字移动通信技术，专注于为您提供便利的操作。

LG KF690 | 用户手册4设置开始了解您的手机...............8打开视图.......................9安装 SIM 卡和电池.............10存储卡 .......................12菜单图 .......................13待机屏幕触摸屏提示....................14状态栏 .......................15从状态栏更改状态..............15使用多任务功能................15基本功能拨号 .......................16 拨打电话 ....................16 从电话本拨打电话 ............16 通话选项 ....................16 调节通话音量 ................17 接听和拒绝电话 ..............17 快速拨号 ....................17 查看通话记录 ................17 使用呼叫转接 ................18 使用呼叫限制 . (18)更改常用通话设置 ............19内容文本输入法文本输入法 (20)电话本 (21)搜索联系人 (21)从待机屏幕 (21)从主菜单 (21)添加新联系人 ................21 联系人选项 (22)创建群组 (22)更改联系人设置 (23)查看信息 (23)信息 (24)发送信息 (24)设置电子邮件 (24)使用新账户发送电子邮件 (26)更改电子邮件设置 (26)信息文件夹 (26)管理信息 (27)使用模板 (27)使用图释 (27)更改文本信息设置 (28)更改多媒体信息设置 (28)更改其它设置 (29)高级功能相机相机 (30)快速拍照 (30)查看保存的照片 (30)查看照片详细信息 (30)了解取景器 (31)摄像机 (32)快速摄像 (32)了解取景器 (32)观看保存的视频 (33)照片和视频照片和视频.................... (34)查看照片和视频 (34)观看视频时调节音量 (34)从视频中拍摄图像 (34)从图片库发送照片或视频 (35)以幻灯片显示方式查看照片 (35)将照片设为墙纸 (35)编辑照片 (35)为照片添加文本 ..............36多媒体.. (37)我的图像 (37)“我的图像”选项菜单 (37)发送照片 (37)我的声音 (38)使用声音 (38)我的视频 (38)观看视频 (38)暂停视频时使用选项 (38)发送视频剪辑 (38)将视频剪辑用作铃声 (38)使用视频选项菜单 (39)我的应用程序 (39)下载游戏 (39)玩游戏 (39)手机证券 (39)Flash 内容 (39)查看 SWF 文件 (39)5查看 SWF 文件时使用选项 .....40 文档 .......................40 将文件传输到手机 ............40 查看文件 ....................40 播放歌曲 ....................41 创建播放列表 ................41 删除播放列表 ................41 FM 收音机 ...................41 搜索电台 ....................41 收听收音机 ..................41网络 访问网页 ....................42 添加并访问书签 ..............42 已保存页面 ..................42 访问已保存页面 ..............42 查看浏览器历史记录 ..........42 更改网络浏览器设置 ..........43 将手机用作调制解调器 ........43 Google .....................43内容管理功能管理器 (44)将事件添加到日历中 (44)更改默认日历视图 (44)向任务列表添加项目 (44)发送任务项 (44)使用日期计算器 (45)设置闹钟 (45)添加备忘录 (45)语音备忘录 ..................46 发送录音 .. (46)使用计算器 (46)向世界时钟添加城市 (46)换算单位 (47)使用秒表 (47)电子词典 (47)SIM 卡应用 (47)PC 同步PC 同步 (48)在计算机上安装LG PC 套件 (48)连接手机和 PC (48)备份和恢复手机信息 (48)在 PC 上查看手机文件 (48)同步联系人 ..................48 将手机用作 Mass Storage 设备 496LG KF690 | 用户手册设置更改屏幕设置 (50)个性化情景模式 (50)更改手机设定 (50)更改连接设置 (51)使用内存管理器 (51)使用蓝牙发送和接收文件 (52)与其它蓝牙设备配对 (53)使用蓝牙耳机 (53)快捷键设置 (53)配件 (54)准则关于安全有效使用手机的准则 (56)网络服务 (62)技术参数 (62)7存储卡插槽电池盖电池闪光灯相机镜头SIM 卡插槽2 卸下电池抬起电池底边，小心将电池从电池室取出。

Page 151 Winthrop RoadChester, Connecticut 06412-0684Phone: (860) 526-9504Internet: Sales e-mail: autosale@Customer Service e-mail: custserv@®ENGINEERING COMPANY INC.For warranty information regarding this product, visit /warrantyA u t o m o t i v e : S i r e n s /S w i t c h e s©1998 Whelen Engineering Company Inc.Form No.13280A (061698)Installation Guide:TACTL690 Control Head to Interface with UPS690WARNING: This product can expose you to chemicals including Lead which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.g ov.J1J19POSITION CONNECTORINPUTCONNECTORP29POSITION CONNECTORINPUTCONNECTORINSERT PINS INTO J1CONNECTORPLUG J1CONNECTOR INTO P2CONNECTORFig.1ConnectionSelecting a Mounting Location:Select a location for the TACTL690 that will be convienent for both operation and viewing for the operator.Wiring your TACTL690:1.Locate the 10 position Input Connector included withyour UPS690 and plug it into the port indicated in Fig. 1.Extend the BLACK and RED wires from the Input Connector towards the battery.WARNING: All customer supplied wires, that connect to the positive (+) terminal of the battery, must be sized to supply at least 125% of the maximum operating current, and fused “at the battery” to carry the load!2.Connect the RED wire to a fuse block (customer supplied)and then to the POSITIVE terminal on the battery.NOTE! Although a 15 amp fuse (customer supplied) is required to be used in the fuse block, do not install the fuse until all of the wire connections are completed.3.Connect the BLACK wire to the factory chassis groundadjacent to the battery.4.Find the J1 9 position connector in your parts bag and insertthe pins from the input connector following the wiring diagram on the next page. (Fig. 2)5.Plug the input connector into your UPS690 and plug theother end into the P2 connector coming from the TACTL690. (Fig. 1 Connection)6.Insert the pins coming from the three cables that come outof the light bar into the six, 3 position pin housings. (Fig. 2)7.Plug the pin housings into the UPS690 carefully followingthe wiring diagram and set the dip switches into the default positions as shown.Installation:Install the TACTL690 under the dash in a convenient location that is both visible and easy to reach, using the two mounting screws included.P5P6DIP SWITCH BANK DIAGNOSTICPORT (NOT USED)INPUT CONNECTORPORTF U S EOUTLETSP3P4P1P2TOP VIEW UPS690READ BEFORE INSTALLING!!!Do not install this product or route any wires in the deployment area of your airbag.Equipment mounted or located in the airbag deploy-ment area will damage or reduce the effectiveness of the airbag,or become a projectile that could cause serious personal injury or death.Refer to your vehicle owners manual for the air bag deployment area.The User/Installer assumes full responsibility to determine proper mounting location,based on providing ultimate safety to all passen-gers inside the vehicle.Whelen Engineering Company assumes no liability or responsibility for determining individual applications or exact installation location criteria.Page 2。

690+Q u i c k S t a r tAssociated Literature690+ Installation Manual HA465492Uxxx 690+ Software Manual HA465038UxxxV I E W L E V E L SThere are three View Levels to the menuOperator – A very simple level . No setup allowed Basic – Default mode of the menu. Allows quick setup, save, restore and full diagnosticsAdvanced- Allows full access to the comprehensive set of function blocks in the Setupmenu and more choices in the System menu to choose Language defaults and moreView Levels may be selected from the Quick Setup menu, under View LevelM AC R O SThe 690+ comes packaged with several Macros, which are preconfigured schemes. Current macros includeBasic speed control - Load this to return to factory default parametersRaise/Lower – Pushbutton ramp using increase/decrease inputsPID – Provides closed loop process controlSPW – Speed program winder (closed loop trim) PRESET SPEEDS – Provides 8 preset speeds To load a Macro, go to SYSTEM\RESTORE CONFIG and select the macro you wish to loadf r a m e s C -F 15-150 H P 7.5-90 k W•3-phase supply to L1, L2, L3. •Motor connections to M1, M2, M3 •Brake resistor between DBR+, DBR- •Motor thermistor to MOT TEMP •Common Bus to DC+, DC-Flux Vector Sensorless VectorVolts/HertzT E C H N O LO G Y B OX E SThe 6055 series of Technology boxes is available to communi-cate with protocols such as De-viceNet, PROFIbus, ModBus, RS485 serial comms, CAN bus and LON works. Any of these may be plugged into the right-side techbox port. Securely snap into place, then tighten the ground screwNetworking a standard 690+ toLINK is done with the LINK techbox. This has a built-in processor that can be configured using DSD, the LINK configuration software.I N T E R NA L L I N K SUnder SETUP\LINKS, you may connect and disconnect internal block diagram connections, to use special functions like PID, winder blocks, diameter block, etc., and to tag analog and digital I/O to selected points inside the drive to suit your application needs. Specify sources and destinations to 50 internal links.The power terminals shown are for frame D. Although other frames may vary slightly in appearance, their terminal designations and functionality are identicalVisit us at USA: (704) 588-3246 UK: +44 (0)1903 737000HA470631U200 Issue 6*HA470631U200-06*••Jumper 19 and 20 if no external trip contactAC MOTOR DRIVE7.5KW 400V 1.3OPERATORMenu at Level 1The 690+ can also be calibrated using the programming tool softwareESCAPE ONE LEVELENTER MENUSCROLL SCROLLThe following is a list of the relevant parameters that you may need to check before starting thedrive. Several of these may not need adjustment if you are running a standard 60Hz, 460V 1800RPM induction motor••••123STARTJOGREVDIRHEALTHN.O.CONTACTRUNNINGN.O.CONTACTSPEEDREFERENCE EXT.TRIP+24VDC。