CCNA第二学期期末练习题

1、要求:(1)VTP域名为benet;密码为123;启用修剪;(2)配置2台3层交换机为VTP的server模式;配置2层交换机为VTP的client模式;(3)设置SW-3L-1是VLAN 2－6的生成树根网桥;设置SW-3L-2是VLAN 7－11的生成树根网桥;在2层交换机上配置速端口与上行速链路;(4)配置路由器接口的IP地址;配置路由器启动RIP路由协议;配置路由器上的默认路由，指向10.1.1.1/24;(5)在3层交换机上配置各VLAN的IP地址;配置两台3层交换机之间的EthernetChannel;(6)配置3层交换机的路由接口;在3层交换机上配置RIP路由协议（1）（2）○1SW1-3L 配置vtp域名benetpassword 123 Server模式SW2-3L同样配置○2SW1-3L启用修剪SW2-3L同样配置○3SW3-2L配置vtp的client模式、SW4-2L、SW5-3L、SW6-3L相同配置（3）设置SW-3L-1是VLAN 2－6的生成树根网桥;设置SW-3L-2是VLAN 7－11的生成树根网桥;在2层交换机上配置速端口与上行速链路;○1SW-3L-1是VLAN 2－6的生成树根网桥;;○2设置SW-3L-2是VLAN 7－11的生成树根网桥○3SW3-2L配置速端口与上行链路，SW4-2L、SW5-2L 、SW6-2L上同样配置（4）配置路由器接口的IP地址;配置路由器启动RIP路由协议;配置路由器上的默认路由，指向10.1.1.1/24○1路由器上配置ip地址○2路由器上配置默认路由和RIP○3SW1-3L各vlan的ip地址○4SW2-3L各vlan的ip地址（5）在3层交换机上配置各VLAN的IP地址;配置两台3层交换机之间的EthernetChannel ○1在SW1-3L配置EthernetChannel;○2在SW2-3L配置EthernetChannel;（6）配置3层交换机的路由接口;在3层交换机上配置RIP路由协议○1SW1-3L上配置路由接口○2SW2-3L上配置路由接口○3SW1-3L上的RIP配置○4SW2-3L上的RIP配置○5在SW1-3L验证RIP○6在SW2-3L验证RIP2、要求:如图所示，四台路由器R1，R2，R3以及R4运行OSPF协议（要求发布各路由器的loopback0地址），R1与R2属于Area1，R2与R3属于Area0，R3与R4属于Area2。

CCNA 2 - Chapter 11What is one advantage of using the cut-through switching method instead of the store-and-forward switching method?has a positive impact on bandwidth by dropping most of the invalid framesmakes a fast forwarding decision based on the source MAC address of the framehas a lower latency appropriate for high-performance computing applications*provides the flexibility to support any mix of Ethernet speeds2A network designer must provide a rationale to a customer for a design which will move an enterprise from a flat network topology to a hierarchical network topology. Which two features of the hierarchical design make it the better choice? (Choose two.)reduced cost for equipment and user trainingless required equipment to provide the same performance levelssimpler deployment for additional switch equipment*easier to provide redundant links to ensure higher availability*lower bandwidth requirements3What are two advantages of modular switches over fixed-configuration switches? (Choose two.)availability of multiple ports for bandwidth aggregationlower forwarding ratesneed for fewer power outlets*lower cost per switchincreased scalability*4Refer to the exhibit. Consider that the main power has just been restored. PC1 asks the DHCP server for IPv4 addressing. The DHCP server sends it an IPv4 address. While PC2 is still booting up, PC3 issues a broadcast IPv4 DHCP request. To which port will SW1 forward this request?to Fa0/1, Fa0/2, and Fa0/4 onlyto Fa0/1, Fa0/2, Fa0/3, and Fa0/4to Fa0/1 and Fa0/2 onlyto Fa0/1, Fa0/2, and Fa0/3 only*to Fa0/1 only5What is one function of a Layer 2 switch?forwards data based on logical addressinglearns the port assigned to a host by examining the destination MAC addressduplicates the electrical signal of each frame to every portdetermines which interface is used to forward a frame based on the destination MAC address*6Refer to the exhibit. Fill in the blank.There are ” 12” collision domains in the topology.7What is a collapsed core in a network design?a combination of the functionality of the access, distribution, and core layersa combination of the functionality of the access and core layersa combination of the functionality of the distribution and core layers*a combination of the functionality of the access and distribution layers 8What are two reasons a network administrator would segment a network with a Layer 2 switch? (Choose two.)to enhance user bandwidth*to eliminate virtual circuitsto create more broadcast domainsto isolate traffic between segments*to isolate ARP request messages from the rest of the networkto create fewer collision domains9Refer to the exhibit.How is a frame sent from PCA forwarded to PCC if the MAC address table on switch SW1 is empty?SW1 forwards the frame directly to SW2. SW2 floods the frame to all ports connected to SW2, excluding the port through which the frame entered the switch.SW1 floods the frame on all ports on the switch, excluding the interconnected port to switch SW2 and the port through which the frame entered the switch.SW1 floods the frame on all ports on SW1, excluding the port through which the frame entered the switch.*SW1 drops the frame because it does not know the destination MAC address.10Place the options in the following order:[+] appropriate for high performance computing applications[+] forwarding process can begin after receiving the destination address [+] may forward invalid frames[#] error checking before forwarding[#] forwarding process only begin after receiving the entire frame [#] only forward valid frames[+] Order does not matter within this group.[#] Order does not matter within this group.11What is a basic function of the Cisco Borderless Architecture distribution layer?aggregating Layer 3 routing boundaries*aggregating all the campus blocksacting as a backboneproviding access to the user12ABC, Inc. has about fifty hosts in one LAN. The administrator would like to increase the throughput of that LAN. Which device will increase the number of collision domains and thereby increase the throughput of the LAN?hubhostNICswitch*13What does the term “port density” represent for an Ethernet switch?the numbers of hosts that are connected to each switch portthe speed of each portthe memory space that is allocated to each switch portthe number of available ports*14Which type of transmission does a switch use when the destination MAC address is not contained in the MAC address table?anycastunicastbroadcast*multicast15What is a basic function of the Cisco Borderless Architecture access layer?aggregates Layer 3 routing boundariesprovides high availabilityaggregates Layer 2 broadcast domainsprovides access to the user*16What information is added to the switch table from incoming frames?source MAC address and incoming port number*destination MAC address and incoming port numberdestination IP address and incoming port numbersource IP address and incoming port number17Fill in the blank.A “converged” network is one that uses the same infrastructure to carry voice, data, and video signals.18An administrator purchases new Cisco switches that have a feature called StackPower. What is the purpose of this feature?It enables many switches to be connected with a special fiber-optic power cable to provide higher bandwidth.It enables the sharing of power among multiple stackable switches.*It enables many switches to be connected to increase port density.It enables many switches to be physically stacked in an equipment rack.It enables AC power for a switch to be provided from a powered patch panel.19Which switch form factor should be used when large port density, fault tolerance, and low price are important factors?fixed-configuration switchmodular switchstackable switch*rackable 1U switch20Refer to the exhibit. Fill in the blank.There are ” 5 ”CCNA 2 - Chapter 2Posted by beotron at 8:59 PM1. A static route that points to the next hop IP will have what administrative distance and metric in the routing table?• administrative distance of 0 and metric of 0• administrative distance of 0 and metric of 1• administrative distance of 1 and metric of 0• administrative distance of 1 and metric of 12. What address can be used to summarize networks 172.16.1.0/24, 172.16.2.0/24, 172.16.3.0/24, and 172.16.4.0/24?• 172.16.0.0/21• 172.16.1.0/22• 172.16.0.0 255.255.255.248• 172.16.0.0 255.255.252.03. The routers in the diagram use the subnet assignments shown. What is the most efficient route summary that can be configured on Router3 to advertise the internal networks to the cloud?• 192.1.1.0/26 and 192.1.1.64/27• 192.1.1.128/25• 192.1.1.0/23 and 192.1.1.64/23• 192.1.1.0/24• 192.1.1.0/25• 192.1.1.0/24 and 192.1.1.64/244. Refer to the exhibit. What is the significance of the /8 in the route to the 10.0.0.0 network?• It indicates that there are 8 hops between this router and the 10.0.0.0 network.• It represents the time, in milliseconds, it takes for a ping to reply when sent to the 10.0.0.0 network.• It indicates that there are 8 subnets in the destination network to which the router can forward packets.• It indicates the number of consecutive bits, from the left, in the destination IP address of a packet that must match 10.0.0.0 to use that route.5. Refer to the exhibit. How will packets destined to the 172.16.0.0 network be forwarded?• Router1 will perform recursive lookup and packet will exit S0/0.• Router1 will perform recursive lookup and packet will exit S0/1.• There is no matching interface associated with network 172.16.0.0 so packets will be dropped.• There is no matching interface associated with network 172.16.0.0 so packets will take gateway of last resort and exit out S0/2.6. A network administrator enters the following command into Router1: ip route 192.168.0.0255.255.255.0 S0/1/0. Router1 then receives a packet that is destined for 192.168.0.22/24. After finding the recently configured static route in the routing table, what does Router1 do next to process the packet? • drops the packet because the destination host is not listed in the routing table• looks up the MAC address of the S0/1/0 interface to determine the destination MAC address of the new frame• performs a recursive lookup for the IP address of the S0/1/0 interface before forwarding the packet• encapsulates the packet into a frame for the WAN link and forwards the packet out the S0/1/0 interface7. Refer to the exhibit. Given the output in the exhibit, how would a clock rate be determined for this link? • The rate would be negotiated by both routers.• A rate would not be selected due to the DCE/DTE connection mismatch.• The rate configured on the DTE determines the clock rate.• The rate configured on the DCE determines the clock rate.8. Refer to the exhibit. Which set of commands will configure static routes that will allow the WinterPark and the Altamonte routers to deliver packets from each LAN and direct all other traffic to the Internet? • WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/1• WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2Altamonte(config)# ip route 198.18.222.0 255.255.255.255 s0/1• WinterPark(config)# ip route 172.191.67.0 255.255.255.0 192.168.146.1• WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2• WinterPark(config)# ip route 172.191.67.0 255.255.255.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/09. Hosts on two separate subnets cannot communicate. The network administrator suspects a missing route in one of the routing tables. Which three commands can be used to help troubleshoot Layer 3 connectivity issues? (Choose three.)• ping• show arp• traceroute• show ip route• show interface• show cdp neighbor d etail10. Refer to the exhibit. A company network engineer is assigned to establish connectivity between the two Ethernet networks so that hosts on the 10.1.1.0/24 subnet can contact hosts on the 10.1.2.0/24 subnet. The engineer has been told to use only static routing for these company routers. Which set of commands will establish connectivity between the two Ethernet networks?• R1(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1R2(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2• R1(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.2R2(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.1• R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1• R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.1R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.2• R1(config)# ip route 0.0.0.0 0.0.0.0 10.1.2.1R2(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.111. Which of the following are displayed by the Router# show cdp neighbors command? (Choose three.) • load• platform• reliability• holdtime• local interface12. Refer to the exhibit. What two commands are required to provide connectivity between the192.168.1.0 and 10.0.0.0 networks without requiring recursive lookup? (Choose two.)• A(config)# ip route 10.0.0.0 255.0.0.0 s 0/1/0• A(config)# ip route 10.0.0.0 255.0.0.0 172.16.40.2• A (config)# ip route 10.0.0.0 255.0.0.0 s 0/0/0• B(config)# ip route 192.168.1.0 255.255.255.0 s 0/0/0• B (config)# ip route 192.168.1.0 255.255.255.0 172.16.40.1• B(config)# ip route 192.168.1.0 255.255.255.0 s 0/1/013. Refer to the exhibit. What two commands will change the next-hop address for the 10.0.0.0/8 network from 172.16.40.2 to 192.168.1.2? (Choose two.)• A(config)# no network 10.0.0.0 255.0.0.0 172.16.40.2• A(config)# no ip address 10.0.0.1 255.0.0.0 172.16.40.2• A(config)# no ip route 10.0.0.0 255.0.0.0 172.16.40.2• A(config)# ip route 10.0.0.0 255.0.0.0 s0/0/0• A(config)# ip route 10.0.0.0 255.0.0.0 192.168.1.214. What happens to a static route entry in a routing table when the outgoing interface is not available? • The route is removed from the table.• The router polls neighbors for a replacement route.• The route remains in the table because it was defined as static.• The router redirects the static route to compensate for the loss of the next hop device.15. A router has one static route to each destination network. Which two scenarios would require an administrator to alter the static routes that are configured on that router? (Choose two.)• The destination network no longer exists.• The destination network is moved to a different interface on the same router.• The path between the source and destination is upgraded with a higher bandwidth link.• A topology change occurs where the exi sting next-hop address or exit interface is not accessible.• The remote destination network interface has to be down for 15 minutes of maintenance.16. Why is it advisable to enter a next-hop IP address when creating a static route whose exit interface is an Ethernet network?• Adding the next-hop address eliminates the need for the router to do any lookups in the routing table before forwarding a packet.• In a multi-access network, the router cannot determine the next-hop MAC address for the Ethernet frame without a next-hop address.• Using a next-hop address in a static route provides a route with a lower metric.• In multi-access networks, using a next-hop address in a static route makes that route a candidate default route.17. The output of the Router# show interfaces serial 0/1 command displays the following:• Serial0/1 is up, line protocol is down.• What is the most likely cause for the line protocol being down?• Serial0/1 is shutdown.• There is no cable connecting the routers.• The remote rout er is using serial 0/0.• No clock rate has been set.18. Refer to the exhibit. Which static route should be configured on Router1 so that host A will be able to reach host B on the 172.16.0.0 network?• ip route 192.168.0.0 172.16.0.0 255.255.0.0• ip rou te 172.16.0.0 255.255.0.0 192.168.0.1• ip route 172.16.0.0 255.255.0.0 S0/0/1• ip route 172.16.0.0 255.255.0.0 S0/0/019. What two devices are responsible for converting the data from the WAN service provider into a form acceptable by the router? (Choose two).• the serial port of the router• a modem• a switch• the ethernet port of the router• a CSU/DSU device• a DTE device20. Which of the following is true regarding CDP and the graphic shown?• CDP running on Router D will gather information about routers A, B, C, and E.• By default, Router A will receive CDP advertisements from routers B and C.• If routers D and E are running different routing protocols, they will not exchange CDP information.• Router E can use CDP to identify the IOS running on Router B.21. Which two statements describe functions or characteristics of CDP? (Choose two.)• It starts up automatically and allows the device to detect directly connected neighbor devices that use CDP.• It operates at the network layer and allows two systems to learn about each other.• It creates a topology map of the entire network.• It allows systems to learn about each other even if different network layer protocols are configured.• It forwards advertisements about routes for faster convergence.22. Which piece of information is available from examining the output of the command show ip interface brief?• Interface speed and duplex• Interface MTU• Errors• Interface MAC address• Interface IP addressCCNA 2 - Chapter 31A network administrator is determining the best placement of VLAN trunklinks. Which two types of point-to-point connections utilize VLAN trunking? (Choose two.)between two switches that share a common VLANbetween a switch and a server that has an 802.1Q NIC*between a switch and a client PCbetween a switch and a network printerbetween two switches that utilize multiple VLANs*2What happens to a port that is associated with VLAN 10 when the administrator deletes VLAN 10 from the switch?The port automatically associates itself with the native VLAN. The port creates the VLAN again.The port goes back to the default VLAN.The port becomes inactive.*3Refer to the exhibit. Interface Fa0/1 is connected to a PC. Fa0/2 is a trunk link to another switch. All other ports are unused. Which security best practice did the administrator forget to configure?Configure all unused ports to a ‘black-hole’ VLAN that is not used f or anything on the network.Disable autonegotiation and set ports to either static access or static trunk.Change the native VLAN to a fixed VLAN that is distinct from all user VLANs and to a VLAN number that is not VLAN 1.All user ports are associated with VLANs distinct from VLAN 1 and distinct from the ‘black-hole’ VLAN.*4Which command is used to remove only VLAN 20 from a switch?no switchport access vlan 20delete flash:vlan.datno vlan 20*delete vlan.dat5A Cisco Catalyst switch has been added to support the use of multiple VLANs as part of an enterprise network. The network technician finds it necessary to clear all VLAN information from the switch in order to incorporate a new network design. What should the technician do to accomplish this task?Erase the startup configuration and reboot the switch.Erase the running configuration and reboot the switch.Delete the startup configuration and the vlan.dat file in the flash memory of the switch and reboot the switch.*Delete the IP address that is assigned to the management VLAN and reboot the switch.6What is the effect of issuing a switchport access vlan 20 command on the Fa0/18 port of a switch that does not have this VLAN in the VLAN database?VLAN 20 will be created automatically.*The command will have no effect on the switch.Port Fa0/18 will be shut down.An error stating that VLAN 20 does not exist will be displayed and VLAN 20 is not created.Which command displays the encapsulation type, the voice VLAN ID, and the access mode VLAN for the Fa0/1 interface?show mac address-table interface Fa0/1show interfaces Fa0/1 switchport*show interfaces trunkshow vlan brief8Place the options in the following order:- not scored -dynamic autononegotiatedynamic desirabletrunk9Port Fa0/11 on a switch is assigned to VLAN 30. If the command no switchport access vlan 30 is entered on the Fa0/11 interface, what will happen?Port Fa0/11 will be returned to VLAN 1.*VLAN 30 will be deleted.An error message would be displayed.Port Fa0/11 will be shutdown.What must the network administrator do to remove Fast Ethernet port fa0/1 from VLAN 2 and assign it to VLAN 3?Enter the no vlan 2 and the vlan 3 commands in global configuration mode. Enter the switchport trunk native vlan 3 command in interface configuration mode.Enter the switchport access vlan 3 command in interface configuration mode.*Enter the no shutdown in interface configuration mode to return it to the default configuration and then configure the port for VLAN 3.11Which two Layer 2 security best practices would help prevent VLAN hopping attacks? (Choose two.)Disable DTP autonegotiation on end-user ports.*Change the management VLAN to a distinct VLAN that is not accessible by regular users.Statically configure all ports that connect to end-user host devices to be in trunk mode.Change the native VLAN number to one that is distinct from all user VLANs and is not VLAN 1.*Use SSH for all remote management access.12In a basic VLAN hopping attack, which switch feature do attackers take advantage of?automatic encapsulation negotiationthe default automatic trunking configuration*an open Telnet connectionforwarding of broadcasts13A Cisco switch currently allows traffic tagged with VLANs 10 and 20 across trunk port Fa0/5. What is the effect of issuing a switchport trunk allowed vlan 30 command on Fa0/5?It allows only VLAN 30 on Fa0/5.*It allows a native VLAN of 30 to be implemented on Fa0/5.It allows VLANs 1 to 30 on Fa0/5.It allows VLANs 10, 20, and 30 on Fa0/5.14Refer to the exhibit. A frame is traveling between PC-A and PC-B through the switch. Which statement is true concerning VLAN tagging of the frame?No VLAN tag is added to the frame.*A VLAN tag is added when the frame is accepted by the switch.A VLAN tag is added when the frame is forwarded out the port to PC-B.A VLAN tag is added when the frame leaves PC-A.15Refer to the exhibit. PC-A and PC-B are both in VLAN 60. PC-A is unable to communicate with PC-B. What is the problem?The native VLAN is being pruned from the link.The VLAN that is used by PC-A is not in the list of allowed VLANs on the trunk.*The trunk has been configured with the switchport nonegotiate command. The native VLAN should be VLAN 60.16What VLANs are allowed across a trunk when the range of allowed VLANs is set to the default value?All VLANs will be allowed across the trunk.*Only the native VLAN will be allowed across the trunk.The switches will negotiate via VTP which VLANs to allow across the trunk. Only VLAN 1 will be allowed across the trunk.17Under which two occasions should an administrator disable DTP while managing a local area network? (Choose two.)on links that should not be trunking*when connecting a Cisco switch to a non-Cisco switch*on links that should dynamically attempt trunkingwhen a neighbor switch uses a DTP mode of dynamic autowhen a neighbor switch uses a DTP mode of dynamic desirable18Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.Which PCs will receive the broadcast sent by PC-C?PC-D, PC-E*PC-A, PC-B, PC-D, PC-EPC-A, PC-BPC-A, PC-B, PC-D, PC-E, PC-FPC-A, PC-B, PC-E19Which two statements are true about VLAN implementation? (Choose two.)The network load increases significantly because of added trunking information.Devices in one VLAN do not hear the broadcasts from devices in another VLAN.*The size of the collision domain is reduced.VLANs logically group hosts, regardless of physical location.*The number of required switches in a network decreases.20Refer to the exhibit. DLS1 is connected to another switch, DLS2, via a trunk link. A host that is connected to DLS1 is not able to communicate to a host that is connected to DLS2, even though they are both in VLAN 99. Which command should be added to Fa0/1 on DLS1 to correct the problem?switchport trunk allowed vlan add 99switchport trunk native vlan 66*switchport mode dynamic autoswitchport nonegotiate21Which switch feature ensures that no unicast, multicast, or broadcast traffic is passed between ports that are configured with this feature?switch port securityPVLAN protected port*ACLVLAN22Fill in the blank. Use the full command syntax.The ” show vlan brief” command displays the VLAN assignment for all ports as well as the existing VLANs on the switch.23Which three statements accurately describe VLAN types? (Choose three).An 802.1Q trunk port, with a native VLAN assigned, supports both tagged and untagged traffic.*A management VLAN is any VLAN that is configured to access management features of the switch.*A data VLAN is used to carry VLAN management data and user-generated traffic.Voice VLANs are used to support user phone and e-mail traffic on a network. VLAN 1 is always used as the management VLAN.After the initial boot of an unconfigured switch, all ports are members of the default VLAN.*24Which command should the network administrator implement to prevent the transfer of DTP frames between a Cisco switch and a non-Cisco switch?S1(config-if)# switchport mode trunkS1(config-if)# switchport mode accessS1(config-if)# switchport nonegotiate*S1(config-if)# switchport mode dynamic desirableS1(config-if)# switchport trunk allowed vlan noneCCNA 2 - Chapter 41What type of IPv6 address is required as a minimum on IPv6 enabled interfaces?staticglobal unicastlink-local*loopbackunique local2In order for packets to be sent to a remote destination, what three pieces of information must be configured on a host? (Choose three.)default gateway*hostnameDNS server addressDHCP server addressIP address*subnet mask*3What two pieces of information are displayed in the output of the show ip interface brief command? (Choose two.)MAC addressesLayer 1 statuses*IP addresses*next-hop addressesinterface descriptionsspeed and duplex settings4Place the options in the following order:next hopdestination networkmetric- not scored -administrative distanceroute timestamproute source protocol- not scored -5Which two items are used by a host device when performing an ANDing operation to determine if a destination address is on the same local network? (Choose two.)destination MAC addressnetwork numberdestination IP address*source MAC addresssubnet mask*6Refer to the exhibit. A network administrator issues the show ipv6 route command on R1. What two conclusions can be drawn from the routing table? (Choose two.)Packets that are destined for the network 2001:DB8:ACAD:2::/64 will be forwarded through Fa0/1.R1 does not know a route to any remote networks.*The interface Fa0/1 is configured with IPv6 address2001:DB8:ACAD:A::12.*Packets that are destined for the network 2001:DB8:ACAD:2::54/128 will be forwarded through Fa0/0.The network FF00::/8 is installed through a static route command.7Refer to the exhibit. What is the purpose of the highlighted field in the line that is displayed from the show ip route command?It indicates that this is a directly connected route.It indicates that this route has been deleted from the routing table. It indicates that this route was learned via EIGRP.*It indicates that this is a default route.8Which two statements correctly describe the concepts of administrative distance and metric? (Choose two.)The metric varies depending which Layer 3 protocol is being routed, such as IP.A router first installs routes with higher administrative distances. The value of the administrative distance can not be altered by the network administrator.Routes with the smallest metric to a destination indicate the best path.* Administrative distance refers to the trustworthiness of a particular route.*The metric is always determined based on hop count.9What are two functions of a router? (Choose two.)It manages the VLAN database.It increases the size of the broadcast domain.It controls the flow of data via the use of Layer 2 addresses.It determines the best path to send packets.*It connects multiple IP networks.*10A packet moves from a host on one network to a device on a remote network within the same company. If NAT is not performed on the packet, which two items remain unchanged during the transfer of the packet from source to destination? (Choose two.)destination MAC addresssource ARP tablesource IP address*destination IP address*source MAC addressLayer 2 header11。

1、解决路由环问题的方法有____ABD_____A. 水平分割B. 路由保持法C. 路由器重启D. 定义路由权的最大值2、下面哪一项正确描述了路由协议_______C__A. 允许数据包在主机间传送的一种协议B. 定义数据包中域的格式和用法的一种方式C. 通过执行一个算法来完成路由选择的一种协议D. 指定MAC地址和IP地址捆绑的方式和时间的一种协议3、以下哪些内容是路由信息中所不包含的_____A____A. 源地址B. 下一跳C. 目标网络D. 路由权值4、以下说法那些是正确的_____BD____A. 路由优先级与路由权值的计算是一致的B. 路由权的计算可能基于路径某单一特性计算，也可能基于路径多种属性C. 如果几个动态路由协议都找到了到达同一目标网络的最佳路由，这几条路由都会被加入路由表中D. 动态路由协议是按照路由的路由权值来判断路由的好坏，并且每一种路由协议的判断方法都是不一样的5、IGP的作用范围是________C_A. 区域内B. 局域网内C. 自治系统内D. 自然子网范围内6、距离矢量协议包括____AB___A. RIPB. IGRPC. IS-ISD. OSPF7、关于矢量距离算法以下那些说法是错误的___A____A. 矢量距离算法不会产生路由环路问题B. 矢量距离算法是靠传递路由信息来实现的C. 路由信息的矢量表示法是(目标网络，metric)D. 使用矢量距离算法的协议只从自己的邻居获得信息8、如果一个内部网络对外的出口只有一个，那么最好配置_____A____A. 缺省路由B. 主机路由C. 动态路由10、在路由器中，如果去往同一目的地有多条路由，则决定最佳路由的因素有_____A_C_A. 路由的优先级B. 路由的发布者C. 路由的metirc值D. 路由的生存时间9、在RIP协议中，计算metric值的参数是_D________A. MTUB. 时延C. 带宽D. 路由跳数10、路由协议存在路由自环问题______A___A. RIPB. BGPC. OSPFD. IS-IS11、下列关于链路状态算法的说法正确的是: ___D______A. 链路状态是对路由的描述B. 链路状态是对网络拓扑结构的描述C. 链路状态算法本身不会产生自环路由D. OSPF和RIP都使用链路状态算法12、在OSPF同一区域(区域A)内，下列说法正确的是____D_____A. 每台路由器生成的LSA都是相同的B. 每台路由器根据该最短路径树计算出的路由都是相同的C. 每台路由器根据该LSDB计算出的最短路径树都是相同的D. 每台路由器的区域A的LSDB(链路状态数据库)都是相同的13、在一个运行OSPF的自治系统之内: _AD________A. 骨干区域自身也必须是连通的B. 非骨干区域自身也必须是连通的C. 必须存在一个骨干区域 ( 区域号为0 )D. 非骨干区域与骨干区域必须直接相连或逻辑上相连14、下列静态路由配置正确的是__D_______A. ip route 129.1.0.0 16 serial 0B. ip route 10.0.0.2 16 129.1.0.0C. ip route 129.1.0.0 16 10.0.0.2D. ip route 129.1.0.0 255.255.0.0 10.0.0.215、以下不属于动态路由协议的是______B___A. RIPB. ICMPC. IS-ISD. OSPf16、三种路由协议RIP 、OSPF 、BGP和静态路由各自得到了一条到达目标网络，路由器默认情况下，最终选选定____D____作为最优路由A. RIPB. OSPFC. BGPD.静态路由17、IGP 包括如下哪些协议_ABD________A. RIPB. BGPC. IS-ISD. OSPF18、路由环问题会引起_______A_A. 慢收敛B. 广播风暴C. 路由器重起D. 路由不一致19、以下哪些路由表项要由网络管理员手动配置_A_______A. 静态路由B. 直接路由C. 动态路由D. 以上说法都不正确20、关于RIP协议，下列说法正确的有: ________AC_A. RIP协议是一种IGPB. RIP协议是一种EGPC. RIP协议是一种距离矢量路由协议D. RIP协议是一种链路状态路由协议21、RIP协议是基于_____A____A. UDPB. TCPC. ICMPD. Raw IP22、RIP协议的路由项在多少时间内没有更新会变为不可达? __C_______A. 90sB. 120sC. 180sD. 240s23、解决路由环路的方法有______ABCDA. 水平分割B. 抑制时间C. 毒性逆转D. 触发更新24、RIP协议在收到某一邻居网关发布而来的路由信息后，下述对度量值的正确处理有哪些?_AD________A. 对本路由表中没有的路由项，只在度量值少于不可达时增加该路由项B. 对本路由表中已有的路由项，当发送报文的网关相同时，只在度量值减少时更新该路由项的度量值C. 对本路由表中已有的路由项，当发送报文的网关不同时，只在度量值减少时更新该路由项的度量值D. 对本路由表中已有的路由项，当发送报文的网关相同时，只要度量值有改变，一定会更新该路由项的度量值25、关于RIP V1和RIP V2，下列说法哪些正确? _BC_______A. RIP V1报文支持子网掩码B. RIP V2报文支持子网掩码C. RIP V2缺省使用路由聚合功能D. RIP V1只支持报文的简单口令认证，而RIP V2支持MD5认证26、在rip中metric等于_____D____为不可达A. 8B. 10C. 15D. 1627、RIP协议引入路由保持机制的作用是____B_____A. 节省网络带宽B. 防止网络中形成路由环路C. 将路由不可达信息在全网扩散D. 通知邻居路由器哪些路由是从其处得到28、与动态路由协议相比，静态路由有哪些优点? AB_______A. 带宽占用少B. 简单C. 路由器能自动发现网络拓扑变化D. 路由器能自动计算新的路由29、在RIP路由协议中，以下有关减少路由自环的方法正确的是__ABC__D_____A. 触发更新是从减少路由自环发生的概率方面来考虑问题的B. 水平分割的方法只对消除两台路由器之间的自环有作用C. 设置抑制时间的方法可能导致路由的慢收敛D. 为了减轻路由自环产生的后果，RIP协议规定了最大跳数30、路由协议在收到某一邻居发布而来的路由信息后，下述对度量值的正确处理有哪些? __BD_______A. 对本路由表中已有的路由项，当发送该路由信息的邻居相同时，只在度量值减少时更新该路由项的度量值B. 对本路由表中已有的路由项，当发送该路由信息的邻居相同时，只要度量值有改变，一定会更新该路由项的度量值C. 对本路由表中已有的路由项，当发送该路由信息的邻居不同时，只要度量值有改变，一定会更新该路由项的度量值D. 对本路由表中没有的路由项，只在度量值少于不可达时增加该路由项31、下面哪些协议是可路由协议(routed protocol)? ____AB_____A. IPB. IPXC. RIPD. NETBEUI32、以下协议属于路由协议的是_____ABCG____A. RIPB. IS-ISC. OSPFD. PPPE. IPF. IPXG. BGP33、下列哪些技术有助于避免路由环路? ___BCDEF______A. 直通交换B. 采用链路状态路由协议C. 水平分割D. 路由保持(holddown)E. 定义最大跳计数F. 路由中毒(poison reverse)34、静态路由的优点包括: ___AD______A. 管理简单B. 自动更新路由C. 提高网络安全性D. 节省带宽E. 收敛速度快35、以下对于缺省路由描述正确的是: ___BC______A. 缺省路由是优先被使用的路由B. 缺省路由是最后一条被使用的路由C. 缺省路由是一种特殊的静态路由D. 缺省路由是一种特殊的动态路由36、对路由器A配置RIP协议，并在接口S0(IP地址为10.0.0.1/24)所在网段使能RIP路由协议，在全局配置模式下使用的第一条命令是: ______A___A. Router ripB. rip 10.0.0.0C. network 10.0.0.1D. network 10.0.0.037、支持可变长子网掩码的路由协议有: __BCD_______A. RIP v1B. RIP v2C. OSPFD. IS-IS38、以下对路由优先级的说法，正确的是____BC_____A. 仅用于RIP和OSPF之间B. 用于不同路由协议之间C. 是路由选择的重要依据D. 直接路由的优先级缺省为039、您认为下列说法哪些是不正确的? ____CD__A. 每条静态路由的优先级也可以不相同B. 缺省情况下路由优先级的次序是 OSPF > RIPC. 路由算法产生一种权值来表示路由的好坏。

ERouting Chapter 1 - CCNA Exploration: 路由协议和概念(版本4.0)1口令可用于限制对Cisco IOS 所有或部分内容的访问。

请选择可以用口令保护的模式和接口。

（选择三项）VTY 接口控制台接口以太网接口加密执行模式特权执行模式路由器配置模式2路由器从相连的以太网接口收到消息后，会更改哪项报头地址，再将消息从另一个接口发送出去？仅第 2 层源地址仅第 2 层目的地址仅第 3 层源地址仅第 3 层目的地址第 2 层源地址和目的地址第 3 层源地址和目的地址3请参见图示。

网络管理员已经为路由器连接到直连网络的接口配置了如图所示的IP 地址。

从路由器ping 相连网络上的主机之间相互ping 都会遭到失败。

此问题最可能的原因是什么？目的网络不存在。

路由器接口的IP 地址必须配置为网络地址而非主机地址。

必须使用no shutdown命令启用接口。

每个接口都必须使用clock rate命令配置4请参见图示。

主机 A ping 主机B。

当R4 收到对以太网接口的ping 时，哪两块报头信息包括在内？（选择两项。

）源IP 地址：192.168.10.129源IP 地址：BBBB.3333.5677源MAC 地址：5555.AAAA.6666目的IP 地址：192.168.10.33目的IP 地址：192.168.10.134目的MAC 地址：9999.DADC.12345网络管理员刚把新配置输入Router1。

要将配置更改保存到NVRAM，应该执行哪一条命令？Router1# copy running-config flashRouter1(config)# copy running-config flashRouter1# copy running-config startup-configRouter1(config)# copy running-config startup-configRouter1# copy startup-config running-configRouter1(config)# copy startup-config running-config6您需要配置图中所示的串行连接，必须在Sydney 路由器上发出以下哪条配置命令才能与Melbourne 站点建立连接？（选Sydney(config-if)# ip address 201.100.53.2 255.255.255.0Sydney(config-if)# no shutdownSydney(config-if)# ip address 201.100.53.1 255.255.255.224Sydney(config-if)# clock rate 56000Sydney(config-if)# ip host Melbourne 201.100.53.27请参见图示。

1Which two statements correctly describe the concepts of administrative distanc metric? (Choose two.)Administrative distance refers to the trustworthiness of a particular route.A router first installs routes with higher administrative distances.The value of the administarive distance can not be altered by the networkRoutes with the smallest metric to a destination indicate the best path.The metric is always determined based on hop count.The metric varies depending which Layer 3 protocol is being routed, such as2Refer to the exhibit. Which statement correctly describes how R1 will determinepath to R2?R1 will install a RIP route using network A in its routing table because theadministrative distance of RIP is higher than EIGRP.R1 will install a RIP route using network A in its routing table because the pafrom RIP is lower than EIGRP.R1 will install an EIGRP route using network B in its routing table because th administrative distance of EIGRP is lower than RIP.R1 will install an EIGRP route using network B in its routing table because th cost from EIGRP is lower than RIP.R1 will install an EIGRP route and a RIP route in its routing table and load b between them.3 Which two statements are true regarding classless routing protocols? (Choosesends subnet mask information in routing updatessends complete routing table update to all neighborsis supported by RIP version 1allows for use of both 192.168.1.0/30 and 192.168.1.16/28 subnets in the sareduces the amount of address space available in an organization4 Which command would the network administrator issue to determine if load balin effect on a router?s how ip protocolss how ip routes how ip interface briefs how ip interface5 Which two conditions would create a setting where the use of a distance-vectorprotocol would be efficient? (Choose two.)the network requires a special hierarchical designfast convergence of the network is crucialthe network is using a hub and spoke topologythe network is using a flat designthere are more than 15 hops between the most distant routers6 What is the purpose of a routing protocol?It is used to build and maintain ARP tables.It provides a method for segmenting and reassembling data packets.It allows an administrator to devise an addressing scheme for the network.It allows a router to share information about known networks with other route It provides a procedure for encoding and decoding data into bits for packet forwarding.7 Which of the following best describes the operation of distance vector routing pThey use hop count as their only metric.They only send out updates when a new network is added.They send their routing tables to directly connected neighbors.They flood the entire network with routing updates.8 What attribute is associated with link-state routing protocols?split horizonpoison reverselow processor overheadshortest-path first calculations9 Why is fast convergence desirable in networks that use dynamic routing protocRouters will not allow packets to be forwarded until the network has converg Hosts are unable to access their gateway until the network has converged.Routers may make incorrect forwarding decisions until the network has conv Routers will not allow configuration changes to be made until the network ha converged.10 Which of the following conditions must be met in order for a network to have conThe routers in the network are operating with dynamic routing protocols.The routers in the network are operating with compatible versions of IOS.The routers in the network are operating with the same routing tables.The routers in the network are operating with consistent routing knowledge.11 Which two statements are true regarding metrics? (Choose two.)RIP uses bandwidth as a metric.OSPF uses delay as a metric.EIGRP uses bandwidth as a metric.OSPF uses cost based on bandwidth as a metric.RIP uses delay as a metric.EIGRP uses hop count only as a metric.12 Which two statements are true regarding the advantages of the use of static routes? (Choosincreased securityreduced effort in configuring routesthe administrator maintains control over routingeasier to implement in a growing networkreduces the chance of routing errorsincreased router resource usage13 The following line of code is displayed in a routing table:R 209.165.201.0/24 [120/2] via 192.168.252.2, 00:00:16, S0/0/0What can be concluded from this output?A packet destined for host 192.168.252.2 will be forwarded out the interface connected t209.165.201.0/24.The value, 120, is used to determine the best path when a router has more than one rou protocol configured for the same destination network.This route was manually configured using the ip route command.192.168.252.2 is an interface on the router that produced this output.14 What will be the result of the following commands?ORL(config)# interface fastethernet 0/0ORL(config-if)# ip address 172.16.3.1 255.255.255.0ORL(config-if)# no shutdownThe 172.16.3.0 network will be routed by any dynamic routing protocol automatically.A routing table entry is made to the 172.16.3.0 network with a code of "C".A static route is required to route traffic to the 172.16.3.0 network.The commands will be saved to the startup-configuration automatically.15 An engineer creates a static route by entering the Router(config)# ip route 10.0.0.0 255.255192.168.1.2 command. What can be concluded about this route?The administrative distance of this route is 1.192.168.1.2 is the address of an interface on this router.This route will display as a directly connected network in the routing table.Packets with a destination IP address of 192.168.1.2 will be forwarded to the 10.0.0.0/24 first.16Refer to the exhibit. Router1 and Router2 are running EIGRP. All interfaces are operational a packets can be forwarded between all networks. What information will be found in the routing Router1?Router1 will have 6 directly connected networks.The administrative distance of the route to network 172.16.0.0 will be 90.The metric for routes to 172.16.0.0 will be 1.The interface that is used to forward packets to 172.16.0.0 will always be the S0/1 interfa 17 The following line of code is present in the routing table:O 10.16.1.0/27 [110/129] via 192.168.1.5, 00:00:05, Serial0/0/1What does the number 129 indicate in this output?The cost for this link has a value of 129.The clock rate on this serial interface is set to 129,000.The next-hop router is 129 hops away from this router.This route has been updated 129 times in this routing table.18 A growing medium-sized manufacturing company recently began to have routing instability iscompany uses static routes and has a mixture of over 30 Cisco and non-Cisco routers. The n administrator has decided to convert the network to dynamic routing. What characteristics of should be considered in this selection process?Distance vector routing protocols, such as RIP, converge more quickly than do link-state protocols.EIGRP can be used on all of the routers in the company.OSPF can be used between the routers.An exterior routing protocol, such as BGP, is recommended for growing companies.19Refer to the exhibit. If RIP is the routing protocol, what is the value metric from router A to network 192.168.5.0/24?345662472420 A router learns two paths with equal metrics to a destination network via the RIP routing protwill the router handle packets to the destination network?The router will install the first route it learned into the routing table.The router will install both routes in the routing table and load balance between the two.The router will put the first route in the routing table, and denote the second route as a ba route.The router will pick the path with the higher bandwidth and will place it in the routing tabl。

CCNA2final期末考试答案A1.A technician configures the Fa0/0 interface on a router with ip address 192.168.3.5 255.255.255.252. What additional comma issued by the technician to activate the interface to forward traffic?Router(config-if)# exitRouter(config-if)# no shutdownRouter(config-if)# clock rateRouter# copy running-config startup-config2Refer to the exhibit. A technician has configured the interfaces on the Router, but upon inspection discovers that interface FastEthernet0/1 is not functioning. Which action will most likely correct the problem with FastEthernet0/1?A clock rate should be added to the interface configuration.The subnet mask should be added to the interface configuration.An interface description needs to be added to the interface configuration.The no shutdown command needs to be added to the interface configuration.3Refer to the exhibit. A router interface is configured with the command ip address 172.16.3.31 255.255.192.0. Which set o values would allow a computer that is connected to the router interface to communicate with remote networks?A: 172.16.3.254B: 255.255.192.0C: 172.16.3.31A: 172.16.3.31B: 255.255.192.0C: 172.16.3.255A: 172.16.3.254B: 255.255.255.0C: 172.16.3.31A: 172.16.3.31B: 255.255.255.0C: 172.16.3.14Refer to the exhibit. On the basis of the show running-config output, which option correctly reflects the routes that will be l routing table?ssss5Refer to the exhibit. PC1 is unable to access the Internet. What is the cause of the problem?An incorrect IP address is configured between the two routers.No static route is configured on Router2.A routing loop has occurred.No routing protocol is configured on either of the two routers.Refer to the exhibit. Which three statements are true of the routing table for Router1? (Choose three.)The route to network 172.16.0.0 has an AD of 156160.Network 192.168.0.16 can best be reached using FastEthernet0/0.The AD of EIGRP routes has been manually changed to a value other than the default value.Router1 is running both the EIGRP and OSPF routing process.Network 172.17.0.0 can only be reached using a default route.No default route has been configured.7Refer to the exhibit. The network has three connected routers: R1, R2, and R3. The routes of all three routers are displaye are operational and pings are not blocked on this network.Which ping will fail?from R1 to 172.16.1.1from R1 to 192.168.3.1from R2 to 192.168.1.1from R2 to 192.168.3.18Refer to the exhibit. A network administrator has configured OSPF using the following command:network 192.168.1.32 0.0.0.31 area 0Which router interface will participate in OSPF?FastEthernet0/0FastEthernet0/1Serial0/0/0Serial0/0/19Refer to the exhibit. The hosts on the R1 LAN are unable to access the Internet. What is incorrectly configured?the IP address of the Fa0/0 interface at R1the IP address of the S0/0/1 interface at R2the IP address of the S0/0/0 interface at R1the subnet mask of the S0/0/1 interface at R210Refer to the exhibit. Host A is having problems accessing server A. All routers have the same EIGRP configuration as rou What should be done so that host A can access server A?Add the command no auto-summary on all routers.Change the network statements to include a wildcard mask.Adjust the EIGRP hello timers to account for the network delay.Add the command eigrp log-neighbor-changes on all routers.Which feature of RIPv2 enables it to function as a classless routing protocol?Subnet masks are included in routing updates.Routing updates are triggered by topology changes.Next-hop addresses are included in routing updates.Multicast addresses are used to send routing updates.12A network administrator must use the subnet 172.16.128.0/18 to create 6 additional subnets each containing up to 2000 h LANs. Which subnet mask should the administrator use to create the new subnets?255.255.224.0255.255.240.0255.255.248.0255.255.252.013 A network administrator is in charge of two separate networks that share a single building. What device will be required to two networks and add a common connection to the Internet that can be shared?hubrouteraccess pointEthernet switch14Refer to the exhibit. What needs to be done to allow these two routers to connect successfully?Add a clock rate to S0/0/0 on R1.Add an interface description to S0/0/1 on R2.Change the serial interface on R2 to S0/0/0 so that it matches R1.Change the IP address of S0/0/1 on R2 so that it is in the same subnet as R1.15In which situation would a default static route be recommended?when connecting an edge router to the Internetwhen variable length subnet masking is in effectwhen there is more than one valid route for a destination networkwhen a destination network has a larger mask than any routes in the routing tableRefer to the exhibit. A network engineer has run the show version command on R3. Upon rebooting, R3 does not load th configuration settings.What could be the cause of this problem?There is insufficient NVRAM.There is insufficient flash memory.The configuration register is not configured with the default setting.The system image file is not located in NVRAM.17Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this?The IP address of host A is incorrect.The default gateway of host A is incorrect.The Fa0/1 interfaces of the two routers are configured for different subnets.The subnet mask for the Fa0/0 interface of R1 is incorrect.18Refer to the exhibit. R1 and R2 are adjacent routers both running RIP. All interfaces on both routers are correctly configur operational. Both routers are configured to include all connected interfaces in routing updates. R2 is not showing any rout the routing table. What is the likely cause?The adjacent interfaces are passive.The distance of 120 exceeds 15 hops.19W hich two technologies can be used in distance vector routing protocols to prevent routing loops? (Choose two.)authenticationlink-state advertisementshold-down timersSpanning Tree Protocolsplit horizon20Which prompt is used to allow a user to change the IP address of an interface on a router?Router>Router#Router(config)#Router(config-if)#Refer to the exhibit. A network administrator adds this command to router R1: ip route 192.168.2.0 255.255.255.0 S0/0/0 result of adding this command?This route is automatically propagated throughout the network.The traffic for network 172.16.1.0 is forwarded to network 192.168.2.0.A static route is established.The traffic for all Class C networks is forwarded to 172.16.1.2.22Refer to the exhibit. What information can be determined from the displayed output?EIGRP packets are waiting to be sent to the neighbors.The adjacencies between the routers are yet to be established.The IP address 192.168.10.10 is configured at serial interface S0/0/1 of router R2.Router R2 is receiving hello packets from a neighbor with the IP address 192.168.10.10 via the R2 S0/0/1 interface.23Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this router entering a password?The login command was not entered on the cons ole line.The enable password should be an enable secret password.No username and password combination has been configured.Console connections cannot be configured to require users to provide passwords.24W hich of the following are primary functions of a router? (Choose two.)packet switchingmicrosegmentationdomain name resolutionpath selectionflow control25Because of a topology change, the next hop IP address in the current static route must be reconfigured. How can a static altered to accommodate a topology change?Negate the existing static route and configure a new static route with the correct next hop IP address.Do nothing. The existing static route will automatically update the next hop entry with the new IP address.Keep the existing static route, reload the router, and configure a new static route with the correct next hop IP addresRefer to the exhibit. All routers are configured with no auto-summary. All routers have a default route via their Serial0/1 Router B receives a packet with a destination of 10.16.1.98. What path will the packet take?B-EB-E-D-AB-E-D-A then loop A-D-A until the TTL expiresB will immediately drop the packet.There is insufficient information to answer the question.27Refer to the exhibit. A network administrator is investigating why data packets with destination addresses of 172.16.10.10 192.168.10.100 are being dropped instead of being forwarded via the static route as expected. After confirming that the ip command has been applied on all routers in the network, what other action should the administrator take to ensure that da these addresses are forwarded via the static route?Check that all routers are configured with the same autonomous system number.Issue the no auto-summary command within the EIGRP configuration of all routers.Issue the no passive-interface command within the EIGRP configuration of all routers.Configure the static route to point to the next hop address instead of the outbound interface.28If a router is booting with its default configuration register setting and its NVRAM lacks boot system commands, from whe router try to load the IOS image first?ROMRAMNVRAMflashTFTP server29T wo routers need to be configured within a single OSPF area. Which two components need to be configured on both rout this? (Choose two.)the same process IDthe same area IDnetwork addresses and wildcard masksthe same router IDthe same loop back address30Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choos10.0.0.0/864.100.0.0/16128.107.0.0/16172.16.40.0/24192.168.1.0/24192.168.2.0/24Which candidate route has the longest match for a packet with a destination address of 10.30.16.48?10.30.0.0/1610.30.15.0/2310.30.16.0/2410.30.16.32/2710.30.16.32/3032W hich three statements are true regarding the encapsulation and de-encapsulation of packets when traveling through a r (Choose three.)The router modifies the TTL field, decrementing it by one.The router changes the source IP to the IP of the exit interface.The router maintains the same source and destination IP.T he router changes the source physical address to the physical address of the exit interface.The router changes the destination IP to the IP of the exit interface.The router sends the packet out all other interfaces, besides the one it entered the router on.33Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two routers are establish a neighbor adjacency. What should the network administrator do to troubleshoot this problem?Check if the interfaces of the routers are enabled.Check the hello and dead intervals between the routers.Check the process ID of both routers.Check if CDP is enabled on all the routers.34W hich mechanism helps to avoid routing loops by advertising a metric of infinity?route poisoningsplit horizonhold-down timertriggered updates35Refer to the exhibit. A device is required to complete the connection between router R1 and the WAN. Which tw o devices for this? (Choose two.)a CSU/DSU devicea modeman Ethernet switcha huba bridge36Why is fast convergence desirable in networks that use dynamic routing protocols?Hosts are unable to access their gateway until the network is converged.Routers will not allow packets to be forwarded until the network is converged.Routers may make incorrect forwarding decisions until the network has converged.Routers will not allow configuration changes to be made until the network has converged.37Refer to the exhibit. R1 is configured properly for a single area OSPF, and R2 has been recently installed in the network. commands is required to configure a single area OSPF for the networks that are connected to R2?R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.1.1.0 0.0.0.3 area 0R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config)# router ospf 2R2(config-router)# network 10.1.1.0 0.0.0.3 area 0R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.1.1.0 0.0.0.3 area 1R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.0.0.0 0.0.0.3 area 138。

CCNA期末测试多选题多选题：1、对于这样一个地址,192.168.19.255/20,下列说法正确的是: （）(A) 这是一个广播地址(B) 这是一个网络地址(C) 这是一个私有地址(D) 地址在192.168.19.0网段上(E) 地址在192.168.16.0网段上(F) 这是一个公有地址答案：CE2、下面有关NAT叙述正确的是（）(A) NAT是英文“地址转换”的缩写，又称地址翻译(B) NAT用来实现私有地址与公用网络地址之间的转换(C) 当内部网络的主机访问外部网络的时候，一定不需要NAT(D) 地址转换的提出为解决IP地址紧张的问题提供了一个有效途径答案：ABD3、关于VLAN下面说法正确的是（）(A) 隔离广播域(B) 相互间通信要通过路由器(C) 可以限制网上的计算机互相访问的权限(D) 只能在同一个物理网络上的主机进行逻辑分组答案:ABC4、下面对路由器的描述正确的是（交换机指二层交换机）（）(A) 相对于交换机和网桥来说，路由器具有更加复杂的功能(B) 相对于交换机和网桥来说，路由器具有更低的延迟(C) 相对于交换机和网桥来说，路由器可以提供更大的带宽和数据转发功能(D) 路由器可以实现不同子网之间的通信，交换机和网桥不能(E) 路由器可以实现虚拟局域网之间的通信，交换机和网桥不能答案:ADE5、关于IP报文头的TTL字段，以下说法正确的有（）（多选）(A) TTL的最大可能值是65535(B) 在正常情况下，路由器不应该从接口收到TTL=0的报文(C) TTL主要是为了防止IP报文在网络中的循环转发，浪费网络带宽(D) IP报文每经过一个网络设备，包括Hub、LAN SWITCH和路由器，TTL值都会被减去一定的数值答案:BC6、VLAN的划分方法有（多选）（）(A) 基于设备端口(B) 协议(C) MAC(D) 物理地址答案:ABCD7、路由项10.0.24.0/21由哪几条子网路由聚合而来（）(A) 10.0.0.25/16(B) 10.0.0.23/16(C) 10.0.0.26/16(D) 10.0.0.22/16答案:AC8、在OSPF中，以下（）是两台路由器成为邻居关系的必要条件。

CCNA复习题一、选择题（每题2分，共80分）1、如下图，两个交换机都使用默认的配置，主机4向主机1发送信息时会使用哪两个目的地址。

（选两个）答案：AFA、主机1的IP地址。

F、路由器R1上的F0/1接口的MAC地址。

2、使用NAT的两个好处是什么？（选择两项）答案：ABA、它可节省公有IP地址。

B、它可增强网络的私密性和安全性。

C、它可增强路由性能。

D、它可降低路由问题故障排除的难度。

E、它可降低通过IPSec实现隧道的复杂性。

3、如下图，对于图中拓扑中vlan之间路由，哪两个选项是正确的？（选两项）答案：DF4、请参见图示，流出R1的流量转换失败，最可能出错的是配置哪个部分？答案：BA、ip nat pool语句B、access-list语句。

C、ip nat inside语句。

D、接口S0/0/2应该拥有一个私有IP地址。

5、以下哪三项是私有IP地址？（选择三项）BCDA、172.16.33.1B、10.35.66.70C、192.168.99.5D、172.18.88.90E、192.33.55.89 F、172.35.16.56、请参见图示。

网络管理员已将192.168.10.0的地址范围分配给网际网络LBMISS，并已使用/29掩码将此地址范围划分为子网，为了满足新建筑的需要，技术人员决定使用第五个子网配置新网络（子网零是第一个子网），根据公司规定，必须始终将第一个可用主机地址分配给路由器接口，并将最后一个可用主机地址分配给工作组服务器。

为了连接到网络，应该在工作组服务器的属性中输入下列哪一项的配置。

答案:CA、IP地址：192.168.10.38 子网掩码：255.255.255.240 默认网关：192.168.10.39B、IP地址：192.168.10.38 子网掩码：255.255.255.240 默认网关：192.168.10.33C、IP地址：192.168.10.38 子网掩码：255.255.255.248 默认网关：192.168.10.33D、IP地址：192.168.10.39 子网掩码：255.255.255.248 默认网关：192.168.10.31E、IP地址：192.168.10.254 子网掩码：255.255.255.0 默认网关：192.168.10.17、路由器接口分配的IP地址为172.16.192.166，子网掩码为255.255.255.248，该IP地址属于哪个子网？答案：DA、172.16.0.0B、172.16.192.0C、172.16.192.128D、172.16.192.160E、172.16.192.168F、172.16.192.1768、如果最多可支持254台主机，网络管理员会为网络地址172.30.1.0分配什么子网掩码？答案：BA、255.255.0.0B、255.255.255.0C、255.255.254.0D、255.255.248.09、下面有关VTP的描述，哪些是正确的? 答案：ABDA、VTP客户模式交换机不能更改本地vlan。

ccna考试题及答案1. 以下哪项是网络层的功能？A. 路由选择B. 错误检测C. 流量控制D. 封装数据包答案：A2. 在OSI模型中，哪一层负责在网络中传输数据？A. 应用层B. 传输层C. 会话层D. 网络层答案：D3. 以下哪个协议是用于在IP网络中发现网络设备的？A. ARPB. RARPC. ICMPD. OSPF答案：A4. 在TCP/IP模型中，哪一层与OSI模型的传输层相对应？A. 应用层B. 互联网层C. 网络接口层D. 传输层答案：D5. 以下哪个地址是一个有效的IPv4地址？A. 192.168.1.256B. 192.168.1.1C. 10.0.0.0D. 172.16.300.1答案：B6. 在配置路由器时，以下哪个命令用于进入全局配置模式？A. enableB. configure terminalC. privileged execD. user exec答案：B7. 以下哪个命令用于在Cisco设备上显示当前配置？A. show running-configB. show startup-configC. show configD. show current-config答案：A8. 在Cisco设备上，以下哪个命令用于保存当前的配置到启动配置文件？A. copy running-config startup-configB. copy startup-config running-configC. save running-configD. save startup-config答案：A9. 以下哪个命令用于在Cisco设备上查看所有接口的状态？A. show interfacesB. show ip interface briefC. show interface statusD. show running-config interface答案：B10. 在Cisco设备上，以下哪个命令用于关闭接口？A. shutdownB. no shutdownC. disableD. no enable答案：A11. 以下哪个命令用于在Cisco设备上启用接口？A. shutdownB. no shutdownC. disableD. no enable答案：B12. 在配置静态路由时，以下哪个命令用于指定下一跳地址？B. ip static-routeC. route ipD. static-route ip答案：A13. 以下哪个命令用于在Cisco设备上清除ARP表？A. clear arp-cacheB. clear arpC. clear arp tableD. clear ip arp答案：D14. 在配置动态路由协议时，以下哪个命令用于在接口上启用RIP？A. ip rip enableB. ip rip receiveD. network rip答案：C15. 以下哪个命令用于在Cisco设备上查看RIP路由表？A. show ip ripB. show ip route ripC. show ripD. show ip protocols答案：B16. 在配置EIGRP时，以下哪个命令用于指定自动汇总？A. metric weightsB. auto-summaryC. network auto-summaryD. no auto-summary答案：B17. 以下哪个命令用于在Cisco设备上查看EIGRP邻居？A. show ip eigrp neighborsB. show eigrp neighborsC. show ip eigrpD. show eigrp interfaces答案：A18. 在配置OSPF时，以下哪个命令用于指定路由器ID？A. router-idB. router ospfC. networkD. area答案：A19. 以下哪个命令用于在Cisco设备上查看OSPF路由表？A. show ip ospfB. show ip ospf databaseC. show ospfD. show ip route ospf答案：D20. 在配置VLAN时，以下哪个命令用于创建一个新的VLAN？A. vlan databaseB. configure terminalC. vlan [vlan-id]D. new-vlan答案：C21. 以下哪个命令用于将接口分配给VLAN？A. switchport mode accessB. switchport mode trunkC. switchport access vlan [vlan-id]D. switchport trunk vlan [vlan-id]答案：C22. 在配置交换机时，以下哪个命令用于将接口设置为Trunk 模式？A. switchport mode accessB. switchport mode trunkC. switchport access vlan [vlan-id]D. switchport trunk vlan [vlan-id]答案：B23. 以下哪个命令用于在Cisco设备上查看VLAN配置？A. show vlanB. show vlan briefC. show vlan detailD. show vlan all答案：B24. 在配置VTP时，以下哪个命令用于将交换机设置为VTP服务器模式？A. vtp mode serverB. vtp mode clientC. vtp mode transparentD. vtp mode off答案：A25. 以下哪个命令用于在Cisco设备上查看VTP状态？A. show vtp statusB. show vtp statisticsC. show vtp passwordD. show vtp configuration答案：A26. 在配置STP时，以下哪个命令用于设置根桥？A. spanning-tree root primaryB. spanning-tree root secondaryC. spanning-tree root primary [priority]D. spanning-tree root secondary [priority]答案：C27. 以下哪个命令用于在Cisco设备上查看STP状态？A. show spanning-treeB. show spanning-tree detailC. show spanning-tree summaryD. show spanning-tree interface答案：A28. 在配置VLAN Trunking Protocol (VTP) 时，以下哪个命令用于设置VTP域名？A. vtp domain [domain-name]B. vtp password [password]C. vtp mode [mode]D. vtp version [version]答案：A29. 以下哪个命令用于在Cisco设备上查看当前的VTP版本？A. show vtp statusB. show vtp statisticsC. show vtp passwordD. show vtp configuration答案：A30. 在配置端口安全时，以下哪个命令用于限制接口上可以学习到的最大MAC地址数量？A. switchport port-security maximum [mac-count]B. port-security maximum [mac-count]C. switchport port-security violation restrictD. port-security violation shutdown答案：A这些题目和答案仅供学习和参考之用，实际的CCNA考试内容和形式可能会有所不同。

以下是针对您未获得满分的试题给出的反馈。

某些交互式试题可能不显示您的答案。

分项分数：1与固定配置的交换机相比，模块化交换机具有哪两个优点？（请选择两项。

）正确响应您的响应每台交换机的成本更低可扩展性更高转发率更低需要的电源插座数目更少带宽聚合可以使用多个端口固定配置交换机价格较低，但是它具有指定数量的端口且不能添加端口。

它们提供的高速端口通常比较少。

为了在包含固定配置交换机的网络上扩展交换，需要购买更多的交换机。

这增加了需要使用的电源插座数量。

模块化交换机只需要购买额外的线卡便可以扩展。

带宽聚合也更容易，因为机箱的背板可以为交换机端口线卡提供所需的带宽。

此试题参考以下领域的内容：Routing and Switching Essentials• 1.1.2 交换网络2思科无边界架构接入层的基本功能是什么？正确响应您的响应聚合第 2 层广播域聚合第 3 层路由边界为用户提供访问权提供高可用性思科无边界架构接入层的功能是为用户提供网络访问。

第 2 层广播域聚合、第 3 层路由边界聚合和高可用性是分布层的功能。

也有说答案是聚合第 3 层路由边界此试题参考以下领域的内容：Routing and Switching Essentials• 1.1.1 融合网络3思科无边界架构分布层的基本功能是什么？正确响应您的响应充当主干聚合所有园区块聚合第 3 层路由边界为用户提供访问权思科无边界架构的分布层的一项基本功能是在不同的VLAN 之间路由。

充当主干和聚合园区块是核心层的功能。

为用户提供访问是接入层的功能。

此试题参考以下领域的内容：Routing and Switching Essentials• 1.1.1 融合网络4若将大端口密度、容错和低价作为重要指标，应使用哪个交换机外形因素？正确响应您的响应固定配置交换机模块化交换机可配备机架的1U 交换机可堆叠式交换机堆叠式交换机可以使用特殊电缆实现互联，从而在交换机之间提供高带宽的吞吐量，并像单个大型交换机一样运行。