R＋F TURBO型钢领和优化的钢丝圈

一、非金属平垫片——HG/T20606-2009（欧系）HG/T20627-2009（美系）二、聚四氟乙烯包覆片——HG/T20607-2009（欧系）HG/T20628-2009（美系）三、金属包覆垫片——HG/T20609-2009（欧系）HG/T20630-2009（美系）四、缠绕式垫片——HG/T20610-2009（欧系）HG/T20631-2009（美系）五、齿形组合垫——HG/T20611-2009（欧系）HG/T20632-2009（美系）六、金属环垫——HG/T20612-2009（欧系）HG/T20633-2009（美系）一、非金属平垫片—HG/T20606-2009\HG/T20627-20091、垫片型式：全平面（FF）突面（RF）凹凸面（MFM）榫槽面（TG）突面带内包边（RF-E）。

2、垫片使用的材料3、垫片尺寸极限偏差FF型和RF型MFM型和TG型4、标记示例a、公称尺寸100㎜、公称压力25的突面法兰，用304不锈钢包边的XB450石棉橡胶板垫片：HG/T20606 垫片 RF-E 100-2.5 XB450/304b、公称尺寸500㎜、公称压力0.6MPa的全平面法兰用三元乙丙橡胶垫片：HG/T20606 垫片 FF 500-0.6 EPDMc、公称尺寸DN400，公称压力Class15的凹凸面法兰，选用厚度为3㎜的无机纤维橡胶压制板垫片：HG/T20627 垫片面性MFM 400-150 NAS（AAA/BBB）注：具体厂商（AAA）和牌号（BBB）钢制管法兰用垫片的几种类型二、聚四氟乙烯包覆垫—HG/T20607-2009\HG/T20628-20091、垫片型式：A型（剖切型）B型（机加工型）C型（折包型）2、垫片使用的材料包覆层：聚四氟乙烯——符合QB/T3625中规定的FSB-2和QB/T3626的规定。

嵌入层：石棉橡胶板或非石棉纤维橡胶板.3、垫片尺寸极限偏差垫片内径D1和外径D4尺寸公差及厚度的极限偏差4、垫片嵌入层常使用的材料5、标记示例a、公称尺寸DN200、公称压力PN10的钢制管法兰用剖切型聚四氟乙烯包覆垫片，嵌入层材料为丁氰橡胶板：HG/T20607 四氟包覆垫（NBR） A 200-10b、公称尺寸DN200、公称压力Class150的钢制管法兰用厚度T为2.5mm的剖切型聚四氟乙烯包覆垫片，嵌入层材料为丁氰橡胶板：HG/T20628 四氟包覆垫（NBR） A 200-150三、金属包覆垫片—— HG/T20609-2009\ HG/T20630-20091、垫片型式：Ⅰ型和Ⅱ型金属包覆垫片；2、垫片的包覆金属材料：3、填充材料：4、垫片尺寸的极限偏差5、标记示例：a、公称尺寸DN500、公称压力PN25、金属包覆层材料为0Cr18Ni9，填充材料为XB450石棉橡胶板的金属包覆垫片：HG/T20609 金属包覆垫片 500-25 304/XB450b、公称尺寸DN500、公称压力Class300、金属包覆层材料为0Cr18Ni9，填充材料为柔性石墨板的金属包覆垫片：HG/T20630 金属包覆垫片 500-300 304/FG四、缠绕式垫片——HG/T20610-2009\HG/T20631-20091、垫片型式：2、垫片材料3、垫片型式和材料代号垫片型式和材料代号(续)4垫片尺寸极限偏差表1——HG/T20610表2——HG/T206316、标记示例a、公称尺寸为DN100、公称压力PN40的钢制管法兰用带内环和对中环的缠绕式垫片（D型），对中环材料为碳钢，金属带材料为0Cr18Ni9，填料为柔性石墨带，内环材料为0Cr18Ni9，其标记为：HG/T20610 缠绕垫 D100-40 1222b、公称尺寸为DN1000、公称压力Class300的大直径钢制管法兰（B系列）用带内环和对中环的缠绕式垫片（D型），对中环材料为碳钢，金属带材料为0Cr18Ni9，填料为柔性石墨带，内环材料为0Cr18Ni9，其标记为：HG/T20631 缠绕垫 D1000 B-300 1222※标志：垫片在对中环上应有永久性标志（如打钢印等）。

ASTM钢管标准对照:l.r5?+f4d,n8]1f(Q$QA323-93(2000)硼铁规格A324-73(2000)钛铁合金三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|so lidwor s|caxa)D4u:|-_&m!B7p#?!T/|A325-00经热处理最小抗拉强度为120/105ksi的钢结构螺栓三维网技术论坛5z(F#f9I3F9M&Q9E"tA325M-00结构钢连接件用高强度螺栓(米制)A327-91(1997)铸铁冲击试验方法三维网技术论坛6^0N+Y;f:P+d*I;^5])c!w0L3E+P:dA327M-91(1997)铸铁冲击试验方法(米制)三维网技术论坛9|)e!y9u#?3C2lA328/A328M-00薄钢板桩三维网技术论坛;V(P(~%s8U:J!D:_A331-95(2000)冷加工合金钢棒+n-h+G#Pj-W9r三维网技术论坛8L0p,Z+`;v.z6NA333/A333M-99低温用无缝与焊接钢管规格A334/A334M-99低温设备用无缝与焊接碳素和合金钢管三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江3P4B;l$_'L0J3r6@7z"q8\4H;`+N9\A335/A335M-01高温用无缝铁素体合金钢管A336/A336M-99e1压力与高温部件用合金钢锻件规格A338-84(1998)铁路,船舶和其他重型装备在温度达到650华氏度(345摄氏度)时使用的可锻铸铁法兰,管件和阀门零件三维网技术论坛8j&q7p$[9`*Z+PA34/A34M-96磁性材料的抽样和采购试验的标准惯例3I:c&v,~+hP%]4i0z'S)G*U&i6L8R.S,H)q3u+UA340-99a有关磁性试验用符号和定义的术语2b"@8F7O:vh/n6O9A341/A341M-00用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法三维网技术论坛#]6ZQ"~1w4Z三维网技术论坛*~6Z+~,|5o7K/P,O%BA342/A342M-99磁铁材料导磁率的试验方法&z-Op&g-o7T6c*KA343-97在电力频率下用瓦特计-安培计-伏特计法(100-1000赫兹)和25厘米艾普斯亭(EPSTEIN)机架测定材料的交流电磁性能的试验方法三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江B&B:e&Z;[:k6@A345-98磁设备用平轧电炉钢A348/A348M-00用瓦特计--安培计--伏特计法(100-10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法A350/A350M-00c要求进行缺口韧性试验的管道部件用碳素钢与低合金钢锻件技术规范0c%E+{:G/yA351/A351M-00容压零件用奥氏体及奥氏体铁素体铸铁的技术规范三维网技术论坛7Q;N2^3q+e/{5@/@3VA352/A352M-93(1998)低温受压零件用铁素体和马氏体钢铸件规格三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa2z/Z6C*I/z4X2T!~A353/A353M-93(1999)压力容器用经二次正火及回火处理的含9％镍的合金钢板A354-01淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格三维网技术论坛8A:A4n!A7S6H0HA355-89(2000)渗氮用合金钢棒"J5j_3q1{+x*@+J(Y6U6E4^6`'L;T%gA356/A356M-98e1蒸汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件三维,cad,机械技术汽车,catia,pro/e,u g,inventor,solidedge,solidw or s,caxa,时空镇江;z:E2}5b,vfA358/A358M-01高温用电熔焊奥氏体铬镍合金钢管三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxasm'a8E.E8H6z#[A36/A36M-00a碳素结构钢技术规范三维网技术论坛)^6X:m*j'I)x0f$NA363-98地面架空线用镀锌钢丝绳&T6S:n!@3K5X:_:A}J三维网技术论坛4l2|2K2s9t4R4\$MA367-60(1999)铸铁的激冷试验方法1G/z/e;K9s0g:YA368-95a(2000)不锈钢和耐热钢丝绳的标准-s7R+I2H3N$d2A369/A369M-01高温用锻制和镗孔碳素钢管和铁素体合金钢管三维网技术论坛2O6N4}"{-f!lA370-97a钢制品机械测试的标准试验方法和定义A372/A372M-99薄壁压力容器用碳素钢及合金钢锻件三维,cad,机械技术汽车,catia,pro/e,u g,inventor,solidedge,solidw orks,caxa,时空镇江9{3Y3]0^,c1B)f#@1L'l9It5a&WA376/A376M-01高温中心站用无缝奥氏钢管A377-99球墨铸铁压力管规范索引三维网技术论坛0G6i7,w!dA380-99e1不锈钢零件、设备和系统的清洗和除垢三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa,m4T.`3g$c三维网技术论坛0I(e2x2E+r/y I:`,G+N^/vA381-96高压输送用金属弧焊钢管9P#N*l(w)J*ec5H,p$vRA384-76(1996)防止钢组件热浸镀锌时翘曲和扭曲用安全保护A385-00提供高质量镀锌覆层(热浸)三维网技术论坛"G4,g-^.h(O2EA3-01低、中、高碳素钢鱼尾（连接）板三维,cad,机械技术汽车,catia,pro/e,u g,inventor,solidedge,solidw or s,caxa,时空镇江-t(F0F4W8T1O[:k%d(].{3JA387/A387M-99e1压力容器用铬钼合金钢板6K"s,~%P7b三维网技术论坛#D-n:R7_#L,m#hA388/A388M-95(2000)e1重型钢锻件超声波检测A389/A389M-93(1998)适合高温受压部件用经特殊热处理的合金钢铸件规格三维网技术论坛2s3D/H*~'R6h9n7Z8s4nA390-95(2001)饲养家禽用镀锌钢丝栏栅网(六角形和直线形)A391/A391M-9880号合金钢链条三维,cad,机械技术汽车,catia,pro/e,u g,inventor,solidedge,solidw orks,caxa,时空镇江9V7R.N't#|4t,ax三维网技术论坛F%q0n:A)IA392-96镀锌钢丝链环栏栅网三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa2[K2WZ.G#a9C8d三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|so lidwor s|caxa9Z'A8a7L-i&@#F,h#xA394-00传动塔架用镀锌和裸露钢螺栓A395/A395M-99高温用铁素体球墨铸铁受压铸件三维网技术论坛4Z'~+M#b%U%B:RA400-69(2000)钢棒的成分及机械性能选择指南三维,cad,机械技术汽车,catia,pro/e,u g,inventor,solidedge,solidw or ks,caxa,时空镇江*c4n!z4g$F8|1a)|&t*^三维网技术论坛6p0s3\T-i0u5N0zA401/A401M-98铬硅合金钢丝!t!v(s'{+^*j/YA403/A403M-00b锻制奥氏体不锈钢管配件A407-93(1998)盘簧用冷拉钢丝三维网技术论坛;[9O;^7K8k4GA409/A409M-01腐蚀场所或高温下使用的焊接大口径奥氏体钢管三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|so lidwor s|caxa2G4L/w%o&N1QA411-98镀锌低碳钢铠装线9A4i;n.j/f7A'Q(~A413/A413M-00碳素钢链A414/A414M-00压力容器用碳素薄钢板A416/A416M-99预应力混凝土用无涂层七股钢铰线A417-93(1998)之字型、方型和正弦型装垫弹簧元件用冷拉钢丝A418-99涡轮机及发电机钢转子锻件的超声波检查方法三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江&V6v-MP-[$l'^5v7o1L#y三维网技术论坛%y/Z5[2tm0~.t:XA420/A420M-00b低温下用锻制碳素钢和合金钢管配件三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa"t&Z.k%o,h$P6p$V2K/i*m2v8E)w"S;U/e!P5])kA421/A421M-98a预应力混凝土用无涂层消除应力钢丝的技术规范三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江)J;@.V/f9~2y8vA423/A423M-95(2000)无缝和电焊低合金钢管A424-00搪瓷用钢薄板三维|cad|机械汽车技术|catia|pro/e|ug|inventor|s olidedge|solidwor s|caxa%r(G1R$O6s三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江'~,}{#a(CP3?;~A426-92(1997)高温用离心铸造的铁素体合金钢管8I5M.c:Z;~-k,V2iA427-74(1996)e1冷轧和热轧用锻制合金钢辊三维网技术论坛/B2v)n#C7j1n(I-RA428/A428M-01钢铁制品上铝覆层重量的测试方法三维网技术论坛-Z:m6\2z-G6v$[7\9C:e)v;^3dA434-90a(2000)热轧与冷精轧经回火及淬火的合金钢棒三维,cad,机械技术汽车,catia,pro/e,u g,inventor,solidedge,solidw orks,caxa,时空镇江1N+a#y2\:_三维网技术论坛+J`-`,]!h1W$B5m+c!F*aA435/A435M-90(2001)钢板的直射束纵向超声波检验三维网技术论坛#w1A0w!E5M2_A436-84(1997)e1奥氏体灰口铁铸件A437/A437M-01高温用经特殊处理的涡轮型合金钢螺栓材料A438-80(1997)灰铸铁横向弯曲试验A439-83(1999)奥氏体可锻铸铁铸件A447/A447M-93(1998)高温用镍铬铁合金钢铸件(25-12级)三维网技术论坛/B:r#f1@2M8XLA449-00经淬火和回火的钢螺栓和螺柱三维网技术论坛4r"\/f0U2m;l2c8p三维网技术论坛"s2r2h([,a$e2LA450/A450M-96a碳素钢管、铁素体合金钢管及奥氏体合金钢管三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江(r"Z&c-t-Y:v)H%_0{/R:`A451-93(1997)高温用离心铸造的奥氏体钢管三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江B'd"`/m$B1^7FA453/A453M-00具有同奥氏体钢相类似的膨胀系数、屈服强度为50-120Ksi(345-827MPa)的耐高温螺栓材料三维网技术论坛"W0g&v9~-e!^'R3D;L)G/]A455/A455M-90(2001)压力容器用高强度碳锰钢板A456/A456M-99大型曲轴锻件的磁粉检查,x?+P0].GA459-97镀锌平轧扁钢铠装带A460-94(1999)包铜钢丝绳标准;C&{;a4R4]8p7x.J&M三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江R:Be3\;gA463/A463M-00热浸镀铝薄钢板(R#N:b6f8L3K*?0B#yA466/A466M-98非焊接碳素钢链A467/A467M-98机器链和盘旋链A469-94a(1999)用于发电机转子的真空处理钢锻件A470-01涡轮机转子和轴用经真空处理的碳素钢和合金锻件三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江0y"\4q9[,n#C/y6h;XA471-94(1999)涡轮转子转盘和转轮用真空处理合金钢锻件技术规范三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa$b,X$z8e'H.r6W A472-98蒸汽涡轮机轴及转子锻件的热稳定性的试验方法A473-01不锈和耐热钢锻件三维,cad,机械技术汽车,catia,pro/e,u g,inventor,solidedge,solidw orks,caxa,时空镇江+R1f*N/F7U9t+}:Q1wA474-98包铝钢丝绳标准三维网技术论坛;^8eb0Q/_'y1c/M4\三维网技术论坛0j(y?.p-g"F#H4[A475-98镀锌钢丝绳三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa7H0Q.6d4A476/A476M-00造纸厂干燥辊用球墨可锻铸铁件:|8O7Z6W"z4OA478-97铬镍不锈钢和耐热钢制编织钢丝三维网技术论坛2c1B!{3h'C*@)U,n9nA479/A479M-00锅炉及压力容器用不锈钢和耐热钢棒与型材三维网技术论坛M#t;G6l(h'u三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|so lidwor s|caxa:l)?6b&V'B%wA47/A47M-99铁素体可锻铁铸件三维,cad,机械技术汽车,catia,pro/e,u g,inventor,solidedge,solidw orks,caxa,时空镇江7{+a0U1`"b/J!}$n9f8uz6h.Z,gA480/A480M-01扁平轧制耐热不锈钢厚板材、薄板材和带材通用要求A481-94(2000)金属铬三维,cad,机械技术汽车,catia,pro/e,ug,in ventor,solidedge,solid work s,caxa,时空镇江9U5H!^4gC5w/{,\7P*oA482-93(2000)铬铁硅三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江s+}l8H4z0q)LA483-64(2000)硅锰合金三维|cad|机械汽车技术|catia|pro/e|u g|inventor|solided ge|solidwor s|caxa(H9b6y0n1e4U3q.y:_A484/A484M-00不锈及耐热锻钢棒,钢坯及锻件的规格三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa%R"L5e,[-l%V)K.n9V"Q9@dA485-00高淬透性耐磨轴承钢的技术规范7D-S4El,F)LA487/A487M-93(1998)受压钢铸件三维网技术论坛)d1n9cn&W7R$j"n9x7qA488/A488M-01钢铸件焊接规程和工作人员的合格鉴定A48-94ae1灰铁铸件三维网技术论坛)U+|$@*{(n/j4V/M5J!A3?'FA489-00碳素钢吊耳m/K.}&H6|#W)|%B,D0~"j*|A490-00最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓0?+W$V4t,H3A.W(wA491-96镀铝钢链环栏栅结构三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa"{(`4w']9J3}:R.q8zA492-95(2000)耐热不锈钢丝绳)n'T1m%y+l+z8v1A:p)A493-95(2000)冷镦和冷锻不锈钢和耐热钢丝3Lh6u#_8B0@*VA494/A494M-00镍和镍合金铸件&}8C&g*K)F%f!\2V"f6bA495-94(2000)硅钙合金钢技术规范三维网技术论坛.I2a7N/w&{2T6U9w7e/sA496-97ae1钢筋混凝土用变形钢丝三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江9j0~!K1F2f!s0W/J7`,S/x)VA497-99e1钢筋混凝土用焊接变形钢丝网A498-98无缝与焊接碳素钢,铁素体钢与奥氏体钢制有整体散热片的换热器钢管三维网技术论坛3U3E"L32H#X 三维网技术论坛(f+?x*]:A$J!S5PA49-01经热处理的碳素钢鱼尾（连接）板，微合金鱼尾板及锻制碳素钢异型鱼尾板三维网技术论坛*x*}(_!T/r+{A499-89(1997)e1轧制丁字钢轨用的碳素钢棒材及型材的技术规范三维网技术论坛1A.h6[*E9k7C&e:R,J$q01}!QA500-01圆形与异型焊接与无缝碳素钢结构管三维,cad,机械技术汽车,catia,pro/e,u g,inventor,solidedge,solidw or ks,caxa,时空镇江i6f7v2H4e-[三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江8OY2_!q$B:x%v4A501-01热成型焊接与无缝碳素钢结构管三维网技术论坛&?:D(Y5j5A;P:@/c*[A503/A503M-01锻制大型曲轴的超声波检验三维网技术论坛k8[#w4T0i-h5Y1a,d三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江:?&T54@%p"z8`3_8A504-93(1999)锻制碳素钢轮三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa:g7x-B.o8U3SA505-00热轧和冷轧合金钢薄板和带材三维网技术论坛8q4v:G+`.I7E+}u-x+.X%r*aj;o4q1tA506-00正规质量及优质结构的热轧和冷轧合金钢薄板与带材*C"B$H5Q6vA507-00优质拉拔,热轧和冷轧合金钢薄板与带材A508/A508M-95(1999)压力容器用经回火和淬火真空处理的碳素钢与合金钢锻件3Z9s-IM.r)E.j'c A510-00碳素钢盘条和粗圆钢丝通用要求A510M-00碳素钢盘条和粗圆钢丝(米制)三维,cad,机械技术汽车,catia,pro/e,ug,in ventor,solidedge,solidwor s,caxa,时空镇江3o5C+C%y)@;s-w-tA511-96无缝不锈钢机械管三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江4T8O7@%n-~%w)qA512-96冷拉对缝焊碳素钢机械管三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa)h7t+`/u/e)o"vA513-00电阻焊碳素钢与合金钢机械钢管A514/A514M-00a焊接用经回火与淬火的高屈服强度合金钢板三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江%y$P5I!];g8R!}A515/A515M-92(1997)中温及高温压力容器用碳素钢板三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa3Y%t2?*g;r0Z三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江$c6Y8F#T"\3VA516/A516M-90(2001)中温及低温压力容器用碳素钢板A517/A517M-93(1999)压力容器用经回火与淬火的高强度合金钢板A518/A518M-99耐蚀高硅铁铸件三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa5X/v#]*e/c/w#I2E2W;n0b2p8VA519-96无缝碳素钢与合金钢机械管三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa"Q*G+^%gls7qA521-96一般工业用闭式模钢锻件A522/A522M-95b(2000)低温用锻制或轧制含镍8%和9%的合金钢法兰,配件,阀门和零件规格:K#o;f3?}:f;T#aA523-96高压管型电缆线路用平端无缝与电阻焊钢管A524-96常温和低温用无缝碳素钢管三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa:B.A.h"H7o&J"r1Y4_6j三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江9p X:D(Q&i%z$A529/A529M-00高强度碳锰结构钢质量-I9g;G0G"e.L)r*J;B5C&|.b9VZA530/A530M-99e1特种碳素钢和合金钢管三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa%w1{3_+K+@:]三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江M2p.V2_:b,aA531/A531M-91(1996)涡轮发电机钢定位环的超声波检验A532/A532M-93a(1999)e1耐磨铸铁三维网技术论坛!X9p)U9P/@'Z-a三维网技术论坛3l-J-g#}!'v$f&GA533/A533M-93(1999)压力容器用经回火和淬火的锰钼及锰钼镍合金钢板I%N&U1B1@$v'Z/s三维,cad,机械技术汽车,catia,pro/e,ug,inventor,solidedge,solidwor s,caxa,时空镇江:H,U0_7@-b3`5x$R2NA534-94用于耐摩擦轴承的渗碳钢'D%S'e&D(U.g1`*S#p,B7KA536-84(1999)e1球墨铸铁件A537/A537M-95(2000)压力容器用经热处理的碳锰硅钢板三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|solidwor s|caxa&O8O'e9R(R%J"A#C8X0z9KA53/A53M-01无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范#L(S0t#B%b/@A539-99天然气和燃料油管线用电阻焊钢盘管三维网技术论坛"_F#c-y-t3C"rA540/A540M-00特殊用途的合金钢螺栓材料三维网技术论坛;i%g4t!d8\-A(_&WA541/A541M-95(1999)压力容器部件用经淬火和回火的碳素钢及合金钢锻件.e*\0d-m,a#C'H7k3三维网技术论坛7X&n:X"b3["[A542/A542M-99e1压力容器用经回火和淬火的铬钼、铬钼钒及铬钼钒钛硼合金钢板A543/A543M-93(1999)压力容器用经回火和淬火的镍铬钼合金钢板三维网技术论坛S-e(l3`'R三维网技术论坛8J!E6T;U;X"?,y)e)V8G*QA550-78(2000)铌铁合金三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|so lidwor s|caxa/K+^$n(_4N&xA551-94(1999)钢轮箍。

派克汉尼汾公司版权所有未经许可不能摘录，翻印。

保留修改权利2021年6月警告销售条件本样本中产品和/或系统或相关产品出现故障，选型不当或使用不当，均可能导致人身伤亡和财产损失。

本文档以及由派克·汉尼汾公司及其子公司和授权经销商提供的其他资料，为具有技术知识的用户提供进一步研究所需的产品和/或系统选项。

重要的是，用户必须对您的应用进行全面的分析，并对当前产品样本中与产品或系统相关的资料进行评估。

由于工作条件以及产品或系统的多样性，用户必须自行分析和测试，并独自承担一切后果，包括:产品和系统的最终选型以及确保满足应用的所有性能、安全和警告等方面的要求。

派克·汉尼汾及其子公司可能会随时对本样本中的产品，包括但不限于:产品的特性、产品的规格、产品的结构、产品的有效性以及产品的价格作出变更而不另行通知.本样本中的所有产品均由派克·汉尼汾公司及其子公司和援权经销商销售。

与派克签订的任何销售合同均按照派克标准条件和销售条件中规定的条款执行(提供复印件备索)。

本公司的密封件，只能在本公司的文件资料述及的应用参数范围与接触介质、压力、温度和存放时间相一致的情况下才能使用。

在规定的应用参数范围外使用以及错误选用不同的材料都可能导致密封件寿命的缩短以及设备的损坏，甚至更严重的后果(如生命安全，环境污染等)。

样本中所列出的工作压力、温度范围、运动速度是极限值，它们之间相互关联、相互影响；在极端的工况下，建议不要同时把各个参数都同时用到极限值。

对于特殊的要求（压力、温度、速度、介质等），请联系派克汉尼汾公司以咨询合适的密封结构、材料、配置、安装建议等。

由于诸多工作参数会影响到流体传动系统及密封元件，这些设备的制造商必须在实际工作条件下测试、验证并批准密封系统的功能与可靠性。

此外，对于不断出现的新的介质（液压油、润滑脂、清洗剂等)，用户特别注意它们与目前所用的密封件弹性体材料的兼容性。

我们建议用户在大批量应用之前，在厂内或现场先做密封材料的兼容性能测试，作为密封产品与系统供应商，我们建议用户遵循我们的这些建议。

Dimensions and pressures for reference only, subject to change.Fig. R86 — HyfersetFig. R87 — Electric PumpFig. R88 — Hand PumpHyfersetParker Hydraulic Ferrule Pre-Setting Tool for Ferulok ® Fittings and EO/EO-2 Metric Fittings PORT ABLE...EFFICIENT ...EASY TO USEThe Hyferset is an efficient, dependable device for pre-setting Parker ferrules on tube of steel and stainless steel. This task is made easy through hydraulic power provided by a hand or electric pump. The equipment is portable, and has an optional sturdy wood carrying case.In hydraulic pre-setting, little physical strength is required by the operator to set ferrules properly. Although the amount of force needed increases as the ferrule size increases, the pressure can be easily achieved.This tool accommodates pre-setting dies for tubes ranging in size from 4 through 32 (1/4” through 2” outside diameter) and 6mm to 28mm O.D. metric sizes. The tube, with tube nut and ferrule, is positioned in the die. The hydraulic “push” of the Hyferset pre-sets the ferrule onto the tube — producing a visible ridge of metal, in front of the sleeve bite edge, that can be easily inspected.Positive Stop Body Dies (For Ferulok Fittings Only)The positive stop body die design eliminates the need for predetermined relief valve settings, pressure gauges or chart reading. Positive stop feature allows for uniform assemblies to be made on tube from 1/4” thru 2”. One set of dies can be used on both steel and stainless steel tube. When used in conjunction with the Ferulok visible bite ferrules, the entire system is the most reliable method available for assembling a fitting to a piece of tube.See Appendix for pre-setting pressures for EO and EO-2 steel fittings.Y ou will find instructions for proper use in the 4393-B1 user manual.COMPONENTS REQUIREDPart Name Part No.*Hyferset (basic unit, no accessories)........................................611011A *Hyferset Adapter.......................................................................6 FLO-S Gauge “T” Adapter......................................................................6 R6LO-S *Hose Assembly.........................................................................910004Gauge Swivel Adapter................................................................6 G6L-S Pressure Gauge (0 - 10,000 psi)................................................900044*Hand pump (10,000 psi, 2 speed).............................................900086Electric pump (10,000 psi, 1/2 HP , 40-125 volt).. (900085)Nut die set (1/4” to 2” O.D.).........................................................See page R39Positive Stop body die (1/4” to 2” O.D.).......................................See page R39Nut Die Set (6mm to 28mm).......................................................See page R40Body Die (6mm to 28mm)...........................................................See page R40* Included in Hyferset KitPart Name Part No.Hyferset Kit.................................................................................611049CIncludes basic unit, hand hydraulic pump, hoseassembly, 1 adapter (6 FLO-S), wooden carrying case, operation manual and video.Fig. R89 — Hyferset KitDimensions and pressures for reference only, subject to change.Fig. R90 — Hyferset WoodCarrying CaseOPTIONAL ACCESSORIESPart Name Part No.Wooden carrying case (651085)Hyferset Body Dies for Ferulok FittingsTube O.D.Size (in.)Part No.41/4...........................................................................720105-463/8...........................................................................720105-681/2...........................................................................720105-8105/8...........................................................................720105-10123/4...........................................................................720105-12147/8...........................................................................720105-1416 1.............................................................................720105-1620 1 1/4..........................................................................720105-2024 1 1/2..........................................................................720105-24322.............................................................................720105-32Hyferset Nut Dies for Ferulok FittingsTube O.D.Size (in.)Part No.41/4...........................................................................680370-463/8...........................................................................680370-681/2...........................................................................680370-8105/8...........................................................................680370-10123/4...........................................................................680370-12147/8...........................................................................680370-1416 1.............................................................................680370-1620 1 1/4..........................................................................680370-2024 1 1/2..........................................................................680370-24322.............................................................................680370-32Fig. R91 — Body DieFig. R92 — Nut Die。

国外细纱钢丝圈型号命名规则
国外细纱钢丝圈型号的命名规则通常包括以下几个方面：
1. 材料标识：一般用英文字母表示，如A代表碳钢，S代表不锈钢。

2. 直径标识：表示细纱钢丝圈的直径大小，一般以毫米为单位。

常见的直径标识有"D"、"d"、"OD"、"ID"等。

3. 截面形状标识：表示细纱钢丝圈的截面形状，常见的形状标识有"O"、"C"、"D"、"E"等。

4. 厚度标识：表示细纱钢丝圈的厚度大小，一般以毫米为单位。

常见的厚度标识有"T"、"t"、"H"等。

5. 表面处理标识：表示细纱钢丝圈的表面处理方式，如镀锌、镀镍、镀银等，常见的表面处理标识有"Z"、"N"、"S"等。

综合以上几个方面，国外细纱钢丝圈的型号命名一般是将以上各项标识组合在一起，形成一个完整的型号。

例如，一个型号为ADS-20-TZ的细纱钢丝圈，表示该细纱钢丝圈材料为不锈钢（A）、直径为20毫米（D）、截面形状为圆形（S）、厚度为2毫米（T）、表面处理方式为镀锌（Z）。

Ｇ８０Ｃｒ４Ｍｏ４Ｖ钢角接触球轴承套圈锻件辗扩工艺改进吴玉成，刘明，付中元，王教翔（中国航发哈尔滨轴承有限公司，哈尔滨　１５００２５）摘要：针对目前航空发动机轴承套圈锻造工艺存在锻造次数较多，加热时间长，表面质量较差及金属流线分布不合理等问题，提出了采用棒料车环坯＋直接辗扩成形的新锻造工艺，解决了锻件由于加热火次较多产生的晶粒粗大和脱碳较深问题，以及后续沟道车削产生的金属流线露头等现象。

新锻造工艺提高了生产效率和轴承的使用寿命。

关键词：滚动轴承；角接触球轴承；套圈；高温轴承钢；锻造；辗扩；金属流线中图分类号：ＴＨ１３３．３３＋１；ＴＧ３１６ 文献标志码：Ｂ ＤＯＩ：１０．１９５３３／ｊ．ｉｓｓｎ１０００－３７６２．２０２１．０１．００８ＩｍｐｒｏｖｅｍｅｎｔｏｎＲｏｌｌｉｎｇＰｒｏｃｅｓｓｏｆＡｎｇｕｌａｒＣｏｎｔａｃｔＢａｌｌＢｅａｒｉｎｇＲｉｎｇＦｏｒｇｉｎｇｓＭａｄｅｏｆＧ８０Ｃｒ４Ｍｏ４ＶＳｔｅｅｌＷＵＹｕｃｈｅｎｇ，ＬＩＵＭｉｎｇ，ＦＵＺｈｏｎｇｙｕａｎ，ＷＡＮＧＪｉａｏｘｉａｎｇ（ＡＥＣＣＨａｒｂｉｎＢｅａｒｉｎｇＣｏ．，Ｌｔｄ．，Ｈａｒｂｉｎ１５００２５，Ｃｈｉｎａ）Ａｂｓｔｒａｃｔ：Ａｉｍｅｄａｔｅｘｃｅｓｓｉｖｅｆｏｒｇｉｎｇｔｉｍｅｓ，ｌｏｎｇｈｅａｔｉｎｇｔｉｍｅ，ｐｏｏｒｓｕｒｆａｃｅｑｕａｌｉｔｙａｎｄｕｎｒｅａｓｏｎａｂｌｅｄｉｓｔｒｉｂｕｔｉｏｎｏｆｍｅｔ ａｌｆｌｏｗｌｉｎｅｄｕｒｉｎｇｆｏｒｇｉｎｇｏｆａｅｒｏｅｎｇｉｎｅｂｅａｒｉｎｇｒｉｎｇｓａｔｐｒｅｓｅｎｔ，ｔｈｅｎｅｗｆｏｒｇｉｎｇｔｅｃｈｎｏｌｏｇｙｉｓｐｒｏｐｏｓｅｄｉｎｗｈｉｃｈｒｉｎｇｂｌａｎｋｉｓｔｕｒｎｅｄｆｒｏｍｂａｒａｎｄｒｏｌｌｅｄ，ａｎｄｌａｒｇｅｇｒａｉｎｓｉｚｅａｎｄｄｅｃａｒｂｕｒｉｚａｔｉｏｎｄｅｐｔｈａｎｄｐｏｏｒｍｅｔａｌｆｌｏｗｌｉｎｅａｆｔｅｒｔｕｒｎｉｎｇｏｆｇｒｏｏｖｅｉｓｓｏｌｖｅｄ．Ｔｈｅｎｅｗｆｏｒｇｉｎｇｐｒｏｃｅｓｓｉｍｐｒｏｖｅｓｔｈｅｐｒｏｄｕｃｔｉｏｎｅｆｆｉｃｉｅｎｃｙａｎｄｔｈｅｓｅｒｖｉｃｅｌｉｆｅｏｆｔｈｅｂｅａｒｉｎｇｓ．Ｋｅｙｗｏｒｄｓ：ｒｏｌｌｉｎｇｂｅａｒｉｎｇ；ａｎｇｕｌａｒｃｏｎｔａｃｔｂａｌｌｂｅａｒｉｎｇ；ｒｉｎｇ；ｈｉｇｈｔｅｍｐｅｒａｔｕｒｅｂｅａｒｉｎｇｓｔｅｅｌ；ｆｏｒｇｉｎｇ；ｒｏｌｌｉｎｇ；ｍｅｔａｌｆｌｏｗｌｉｎｅ Ｇ８０Ｃｒ４Ｍｏ４Ｖ钢具有高强度、高硬度和好的高温下尺寸稳定性以及优良的接触疲劳性能，广泛应用于航空发动机主轴轴承。

613004210216130042102161300421021T e m p e r a t u r eT T T 61300421021Cautions and Warnings:The following conditions apply to all goods within the product series of the Connectors of Würth Elektronik eiSos GmbH & Co. KG:General:•This mechanical component is designed and manufactured for use in general electronic equipment.•Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network, etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury.•Mechanical components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer.•The mechanical component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the component may be damaged or dissolved.•Do not drop or impact the components, the component may be damaged.•Prevent any damage or scratches on the component, especially on the actuator.•Direct mechanical impact to the product shall be prevented (e.g overlapping of the PCB´s).•Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time.•The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply to customer specific products.•The mechanical component is designed to be used along with Würth Elektronik counterparts and tools. Würth Elektronik cannot ensure the reliability of these components while being used with other products.Product Specific:Soldering:•The solder profile must comply with the technical product specifications. All other profiles will void the warranty.•All other soldering methods are at the customers’ own risk.Cleaning and Washing:•Washing agents used during the production to clean the customer application might damage or change the characteristics of the component, body, pins and termination. Washing agents may have a negative effect on the long-term functionality of the product.•Using a brush during the cleaning process may deform function relevant areas. Therefore, we do not recommend using a brush during the PCB cleaning process.Potting and Coating:•If the product is potted in the customer application, the potting material might shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the components. Expansion could damage the components. Werecommend a manual inspection after potting or coating to avoid these effects.Storage Conditions:• A storage of Würth Elektronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment.•Do not expose the components to direct sunlight.•The storage conditions in the original packaging are defined according to DIN EN 61760-2.•The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components. Handling:•Do not repeatedly operate the component with excessive force. It may damage or deform the component resulting in malfunction.•In the case a product requires particular handling precautions, in addition to the general recommendations mentioned here before, these will appear on the product datasheet.These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable.However, no responsibility is assumed for inaccuracies or incompleteness.Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODATo001.0012020-06-02DIN ISO 2768-1mDESCRIPTIONWR-PHD Angled Dual Pin HeaderORDER CODE61300421021SIZE/TYPE BUSINESS UNIT STATUS PAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODATo001.0012020-06-02DIN ISO 2768-1mDESCRIPTIONWR-PHD Angled Dual Pin HeaderORDER CODE61300421021SIZE/TYPE BUSINESS UNIT STATUS PAGE。

w w w.p a n d u i t.c omk e y f e a turesa n db e n e f i t sStrength to weight ratio The design of the Wyr-Grid ®Pathway Sections provides a greater strength to weight ratio than competitive wire basket;easier handling translates into faster installationGrid patternThe 4" x 5" wire mesh grid pattern allows greater amounts of cables and QuickNet ®Cassettes to pass through grid openings without additional cutting, reducing installation timeNo integral sidewalls Less cutting on straight sections, no cutting at intersections and waterfalls reduces installation timeSnap-on sidewalls Sidewalls can be attached where needed to retain cables within the Wyr-Grid ®Pathway Sections providing greater configuration versatility Bend radius Protects cables at intersections and can be easily attached without control sidewalls cutting or fabricationBonding splice A thread cutting screw pierces the paint of adjacent cable tray sections providing a completely bonded connection, ensuring electrical continuity between the sectionsSnap-on waterfalls Protects cables when transitioning down to equipment and can be easily attached without cutting or fabricationBlack painted finishProvides corrosion protection;matches equipment racks and cabinets24" and 30" splice:WGSPL2430BL Intersection splice:WGINTSPLBL 2" sidewall:4" sidewall:WGSDWL4BL4" sidewall waterfall:WGSDWWF4BL 18" trapeze bracket:WGTB18BL 24" trapeze bracket:WGTB24BL 30" trapeze bracket:WGTB30BL12" cantilever bracket:WGCB12BL 18" cantilever bracket:WGCB18BL 24" cantilever bracket:WGCB24BL 12" wall bracket:WGWMTB12BL18" – 30" wall bracket:WGWMTB1830BLStrut bracket:WGSTRKTBL4" high sidewall:WGINTBRC4BL 6" high sidewall:WGINTBRC6BLManual cutting tool:WGCT -M Hydraulic cutting tool:WGCT -AHardware kit:WGHRDWKTBL 18"W x 120"L:WG18BL1024"W x 120"L:WG24BL10Wyr-Grid ®Overhead Cable Tray Routing SystemMaterial:Pre-galvanized steel wire and galvanized cold rolled steel prior to paint ABS (Sidewall Waterfall)RoHS CompliantApprovals:UL Classified for their suitability for use as Equipment Grounding Conductor in accordance with Sections 392.3(C) and 392.7(B) of the NECMetal Cable Tray in accordance with CAN/CSA-C22.2 No.126.1-02 NEMA VE 1-2002 and ANSI/NFPA 70, “National Electric Code”(NEC)Corrosion resistant per ASTM A653/A653M-08 and A641/A641M-09EN61537:2007 Cable Tray Systems and Cable Ladder Systems for Cable Management (pending)CSI spec form:LP-CSISPEC-WGWire fill table:a p p l i c a t i o n st e c h n i c a l i nf o r m a t i o ns p e c i f i c a t i o n sThe overhead cable tray routing system shall consist of pathway sections, splice connectors, sidewalls, waterfalls, mounting brackets,and accessories designed to route and manage copper, fiber optic, or power cables.The pathway sections shall be provided in four widths:12" (305 mm), 18" (457 mm), 24" (610 mm) and 30" (762 mm).Optional snap-on sidewalls shall include 2" (50mm), 4" (102 mm), and 6" (152 mm) heights that can be hand installed at any location along pathway sections.Sidewall waterfalls and intersection bend radius parts shall provide 3" (76 mm) bend radius protection.T rapeze, cantilever,and wall mount brackets shall be provided to support the system.All components shall be painted black.The Wyr-Grid ®Overhead Cable Tray System is designed to route and manage copper datacables, fiber optic, or power cables within data cen-ters, connected buildings, and industrial automation applications.Innovative featuresprovide quick, easy assembly for reducedinstallation costs and faster deployment.Can easily accommodate FiberRunner ®Pathways into theapplication to provide a segregated copper and fiber cabling strategy.YP a t h w a y S e c t i o n sM o u n t i n g B r a c k e t s123412" Width:WG12BL1018" Width:WG18BL1024" Width:WG24BL1030" Width:WG30BL1056712" Wide:WGTB12BL(not shown)Trapeze Brackets18" Wide:WGTB18BL 24" Wide:WGTB24BL 30" Wide:WGTB30BLS p l i c e C o n n e c t o r s101112For 12" & 18" Widths:WGSPL1218BL For 24" & 30" Widths:WGSPL2430BL Intersection Splice:WGINTSPLBL812" Wide:WGCB12BL 18" Wide:WGCB18BL(not shown)24" Wide:WGCB24BL(not shown)912" Wide:WGWMTB12BL (not shown)Wall Mount Termination Brackets18 – 30" Wide:WGWMTB1830BL131415S n a p -O n S i d e w a l l sW a t e r f a l l sAc c e s s o r i e s2" Sidewall:WGSDWL2BL 4" Sidewall:WGSDWL4BL 6" Sidewall:WGSDWL6BL181920I n t e r s e c t i o n B e n d R a d i u s C o n t r o l2" High Sidewall:WGINTBRC2BL 4" High Sidewall:WGINTBRC4BL 6" High Sidewall:WGINTBRC6BL21Hardware Kit:WGHRDWKTBL16174" Sidewall Waterfall:WGSDWWF4BL Bottom Waterfall:WGBTMWFBL123567891011121314415161718192120Cantilever BracketsWyr-Grid ®Overhead Cable Tray Routing System©2011 Panduit Corp.ALL RIGHTS RESERVED.WW-FRSP128/2011WORLDWIDE SUBSIDIARIES AND SALES OFFICESFor a copy of Panduit product warranties, log on to /warrantyPANDUIT CANADAMarkham, Ontario ******************Phone: 800.777.3300PANDUIT EUROPE LTD.London, UK*******************Phone: 44.20.8601.7200PANDUIT JAPAN Tokyo, Japan********************Phone: 81.3.6863.6000PANDUIT SINGAPORE PTE. LTD.Republic of Singapore *****************Phone: 65.6305.7575PANDUIT AUSTRALIA PTY. LTD.Victoria, Australia ******************Phone: 61.3.9794.9020PANDUIT LATIN AMERICA Guadalajara, Mexico *****************Phone: 52.33.3777.6000ContactCustomerServicebyemail:**************or by phone: 800.777.3300 and reference FRSP12Visit us at For more information。