霍尼韦尔安全开关(通用版)

微动开关Honeywell目录号说明电气数据和UL代码O.F.Noz最小R.F.Noz最大RT.mmin最小O.T.mminD.T.mmin最大O.P.*mmin 3MN1 用于大多数应用场合15 AV3,34-5,5612.201,6761,52.0602,03.0800,38-0,63.015-.0252,16.085 3MN6 力较小场合 15AV1,95-3,17-111,1141,52.0602,03.0800,38-0,63.015-.0252,16.085Honeywell/Commercial Switch-Sensor 霍尼韦尔开关与传感器1上海: Tel:021-******** 北京: Tel:010-******** 深圳: Tel:0755-******* 广州: Tel:020-******** e-mail:jian.bo.zhou@/ /sensing双断3MN系列特点.080英寸的最小超行程有高达15 A的功率负荷开关容量有240 vac时1马力的电动机处理能力机械寿命长达10,000,000次循环-95%完好率用抗弧塑料端子与端子间间距更大，能有效地降低短路的可能性用8号接线螺钉UL，CSA认证一般信息3MN开关可与限位或控制机构一起用在机床、压力机或其它工业设备上。

这些开关在安装时容易连接。

双断开关端子的接线必须在同一电压源和同一极上。

其负荷应在线路的同侧。

电气额定值电路电气数据和UL标准双电路双断V 电动机控制15A，120，240，480或600 vac;1/2HP，120 vac; 1hp，240 vac;0.8A，115 vdc;0.4A，230 vdc。

特性:O.F.-动作力; R.F.-释放力; P.T.-预行程;订货指南O.T.-超行程; D.T.-差动行程; O.P.-操作位置外形图，图1*±0.38 mm±.015 in安装尺寸(仅供参考)0,0=mm图例:0.00=in直径的安装孔(2)图1。

特点：●3.8-30VDC 供电 ● 数字电流沉输出 ● 3针一列PCB 引脚● 方块霍尔设计消除了机械压力效应 ● 磁特性温度补偿● 可定制特殊的动作/释放点 ● 双极，单极，锁存型●很高的输出电流能力——最大绝对电流50mA ● 动点/释放点对称于零点高斯（双极锁存） ● 工作温度范围-40～150℃ ● 封装材料：Plaskon 3300H● 表面封装型号：SS400-S （切短或整形的引脚）SS400 内含整个温度范围的热平衡集成电路，负的温度补偿特性能与低成本磁钢负温度系数为最佳匹配带宽间隙调整提供了SS400 在3.8～30VDC 电源电压范围内特别稳定的工作特性。

SS400能连续输出20mA 电流，最大绝对电流为50mA.SS411A 双极3.8-3010mA 电流沉.40V 20mA 10µA.05µs 典型值1.5µs 最大值.15µs 典型值1.5µs 最大值G 70-701565-651560-601560-601265-651270-7010mT 7.0-7.01.56.5-6.51.56.0-6.01.56.0-6.01.26.5-6.51.27.0-7.01.0注：当锁存型突然掉电后，其输出在上电后可能改变状态，在足够强的磁场中，传感器的输出由所在磁场决定。

上升(10-90%)下降(90-10%)最大动作点最小释放点最小回差最大动作点最小释放点最小回差最大动作点最小释放点最小回差最大动作点最小释放点最小回差最大动作点最小释放点最小回差最大动作点最小释放点最小回差选型指南型号磁场类型供电电压（VDC ）供电电流（最大值)输出类型输出电压（最大值）输出电流（最大值）*输出漏电流（最大值）输出开关时间Vcc=12V ，RL=1.6K C=20pF 磁特性-40℃0℃25℃85℃125℃150℃SS413A 双极3.8-3010mA 电流沉.40V 20mA 10µA.05µs 典型值1.5µs 最大值.15µs 典型值1.5µs 最大值SS441A 单极3.8-3010mA 电流沉.40V 20mA 10µA.05µs 典型值1.5µs 最大值.15µs 典型值1.5µs 最大值SS443A 单极3.8-3010mA 电流沉.40V 20mA 10µA.05µs 典型值1.5µs 最大值.15µs 典型值1.5µs 最大值SS449A 单极3.8-3010mA 电流沉.40V 20mA 10µA.05µs 典型值1.5µs 最大值.15µs 典型值1.5µs 最大值SS461A 锁存3.8-3010mA 电流沉.40V 20mA 10µA.05µs 典型值1.5µs 最大值.15µs 典型值1.5µs 最大值SS466A 锁存3.8-3010mA 电流沉.40V 20mA 10µA.05µs 典型值1.5µs 最大值.15µs 典型值1.5µs 最大值G 140-14020140-14020140-14020140-14020140-14020140-14020mT 14.0-14.02.014.014.02.014.0-14.02.014.0-14.02.014.0-14.02.014.0-14.02.0G 1352015117201811520201201515123158125105mT 13.52.01.511.72.01.811.52.02.012.01.51.512.31.50.812.51.00.5G 21580251908025180752518070151906010200555mT 21.58.02.519.58.02.518.07.52.5187.01.519.06.01.020.05.50.5G 435210304002303039023530400215304102003042018530mT 43.521.03.040.023.03.039.023.53.040.021.53.041.020.03.042.018.53.0G 110-1105090-905085-855085-8550100-10050110-11050mT 11.0-11.05.09.0-9.05.08.5-8.55.08.5-8.55.010.0-10.05.011.0-11.05.0G 200-200200185-185200180-180200180-180190180-180160185-185140mT 20.0-20.020.018.5-18.520.018.018.020.018.0-18.019.018.0-18.016.018.5-18.514.0注：可订购安装在线带和卷带上的SS400，引脚上间距0.1”, 每个卷带3000个SS400传感器。

电路系统 电气数据和UL 代码除订货 指南中 另有说 明外均 为单刀双掷K 用非极化开关建立的额定值 10A,125 vac 或vdc 1/4马力,125 vac 或vdc UL 代码L 168 非极化:10A 电阻或1/4马力125 vdc 3A 最大电阻250 vdc 极化:10A 电阻或1/2马力125 vdc 3A 最大电阻,250 vdc*为进行极化将线路的负极侧连至共用端子为获得同样的效果用黄铜螺钉安装开关并在开关和安装表面间使用一非磁性塞(至少1/4”厚)特 点• 耐电弧开关壳• 机械寿命:100,000次动作后95%完好• 温度极限为+180°F(82°C) • 与Z 开关可互换安装 • UL 认可可供的端子钎焊(无目录号标志)总体介绍MT(单刀双掷)磁性灭弧开关设计成用于高开断容量(125和250VDC)的系统在触头间隙周围的整体磁铁使电弧偏移从而保护了触头盖和壳体间的通风口能让热气体逃逸这些开关设计成用于控制直流电动机电磁线圈等 A286-32NC ×.218”螺钉 可连接粗达12号线电气额定值特 性:O.F.-动作力; R.F.-释放力; P.T.-预行程 O.T.-超行程; D.T.-差动行程;O.P.-操作位置订货指南目录号建议用于电气数据和UL 代码O.F. N oz R.F .最小N oz R.T.最大 mm in O.T .最小 mm in D.T .最大 mm in O.R. mm in MT-4R-A28销钉式柱塞 单刀双掷10A K3,34-5,0 12-181,39 51,02 .040,13 .0050,1-0,18 .004-.00715,9±0,38 .625±.015外形图图1订货指南名称电气数据和UL代码O.F.最大NozR.F.最小NozR.T.最大mminO.T.最小mminD.T.最大mminO.R*mmin MT-4RV-A28 直杠杆 10AK0,5620,140.512,70.51,19.0472,16.08519,1.750外形图图2MT-4RV2-A28 1,90in(48,3mm)杠杆带有淬火钢滚轮10AK0,762.750,070.258,890.350,79.0311,65.06530,21.188MT-4RV22-A28 1,03in(26,2mm)杠杆带有淬火钢滚轮10AK1,254.50,2815,08.2000,38.0150,89.03531,31.234外形图图3MT-4RL-A28 1,95in(49,5mm)柔性刀形叶片10AK3,34120,281- 1,52.060最大19,1.750外形图图4MT-4RL2-A28 1,82in(46,2mm)柔性刀形叶片带淬火钢滚轮10AK3,34120,281- 1,52.060最大30,21.188外形图图5另有说明除外±0,76mm±.030in安装尺寸(仅供参考)销钉式柱塞直杠杆直径图1图2滚轮杠杆柔性刀形叶片直径宽滚轮图3 图4柔性滚轮刀形叶片直径宽滚轮图5安装孔接受.139”(3,53mm)直径的销钉或螺钉0,0=mm图例:0,00=in。

霍尼韦尔PKS系统操作手册目录第一章.控制系统介绍 (3)1.Honeywell公司PKS系统概述 (3)2.我公司PKS系统配置 (4)第二章.过程操作 (5)1.画面介绍及操作 (5)1.1.标准画面介绍及操作 (5)1.2.状态行介绍（Unde rstanding the Status Line） (6)1.3.工具栏介绍（Using the Toolbar） (8)1.4.点细目画面及操作 (10)1.5.操作组画面及其操作 (20)1.6.报警功能及其画面操作 (22)1.7.信息摘要及其画面操作 (30)1.8.事件摘要及其画面操作 (32)1.9.警报摘要及其画面操作 (33)1.10.总貌画面 (34)1.11.用户流程图介绍 (34)2.历史数据和趋势操作 (37)2.1.历史数据： (37)2.2.趋势： (38)第一章. 控制系统介绍1.Honeywell公司PKS系统概述DCS系统采用霍尼韦尔的Experion PKS过程知识系统。

Experion PKS 系统是当代最先进的控制系统之一，包含了霍尼韦尔三十年来在过程控制、资产管理、行业知识等方面积累的经验，采用最先进的开放平台和网络技术，为工业企业提供一个统一的、全厂的、自动化过程控制、设备和资产管理、直至生产管理、集成制造等一体化的知识系统体系结构和全系列的解决方案。

Experion PKS系统能满足各种自动化应用要求，为过程控制、SCADA应用和批量控制提供一个开放式控制系统，且满足业界要求的高性能、灵活性、易用性、高可靠性等。

典型Experion PKS系统的体系结构如下图1所示。

图12.我公司PKS系统配置霍尼韦尔提供的系统覆盖范围包括中央控制室、6个现场机柜室，由提供的光纤网络以星形连接方式连接中央控制室和与其关联的各个现场机柜室。

网络图如下图2：图2硬件配置方面，霍尼韦尔公司为神达、昊达公司配置的是PKS系统最新版本R410，其配置如下：l控制器：Experion PKS系统的C300控制器作为DCS主控制器，性能强大，可以与多种IO卡件兼容。

■ 技术规格• 工作频率（机械）……………………………120次/分（电气）………………………………………10~30次/分• 接触电阻（初始值）…………………………最大30mΩ • 绝缘电阻（500VDC条件下）……………最小100MΩ• 介电强度……………………AC1,000V RMS (50-60Hz)• 存贮湿度………………………………最高相对湿度85%• 存贮温度…………………-25℃至+85℃，120℃可选• 使用寿命机械…………………………………至少10,000,000次电气………………………………………至少10,000次■ 额定参数100.1A:30VDC-125-250VAC5A:125VAC/250VAC505A:125/250VAC 6A:125/250VAC9010.1A:125/250VAC■ 接触形式电话、空调、计算机、加湿器、报警器、时间记录器、混合器、断路器、钎焊枪、霓虹（neon）电话、传真机、操纵杆、水泵、瓦斯探测器、铅笔刀、纸币分拣机、食品加工机、电动刀、玩具汽车、榨汁机、灯具、牛排电烤盘。

■ 用途• 小型紧凑尺寸• 客户定制• 移动揩拭触点动作• 外部安全操作机构• 长寿命螺旋弹簧机构■ 特性■ 尺寸（除另有声明外，所有尺寸参数的公差均为± 0.4mm）• ZV系列微动开关ZV系列m m [i n]注（1）采用上述命名法是为了达到识别产品的目的，不是所有的组合都有。

未列入变形件的建立要求最低的数量。

（2）额定参数为10.1A 的开关只能用“H ”型动作力度，以符合V D E 生命周期测试。

（3）“99”型端子或“S ”型操作机构用于标识特殊型号，因此在名称的最后需要有一个特殊的标识字母。

（4）如果要建立一个新的命名法可能需要通知U L 和欧洲的审批机构。

（5）杠杆长度按下面的方法测量：直杠杆-从轴枢中心线到按挚的末端；滚轮杠杆或相似滚轮杠杆-从轴枢点中心线到滚轮直径中心线。

霍尼韦尔净化器安全操作及保养规程随着现代生活水平的不断提高，人们对生活环境的要求也越来越高。

在生活中，空气净化器被越来越多的人所使用。

霍尼韦尔净化器是一款高端的净化器，具有较高的净化效果和易于操作的特点。

下面，本文将介绍霍尼韦尔净化器的安全操作及保养规程，以帮助用户正确认识和使用净化器。

一、安全操作规程1.1 电源插头在插拔电源插头时应该始终保持手干燥，确定插头已连接到插座上，并确认插座电压与净化器电压相同。

同时，按下插头或插座上的开/关开关，并确保净化器已打开。

1.2 防火安全使用净化器时，不要在净化器附近放置易燃材料，并确保周围有足够空间进行通风。

除了推荐的滤芯和配件外，不要使用其他零部件。

1.3 禁止拆卸在使用净化器时，不要对净化器进行任何拆卸或维修操作。

不用时，将净化器从插座上拔下，并将其放在干燥，安全的地方。

1.4 离开房间如果需要暂时离开房间，建议将净化器关闭并拔掉电源插头。

如果长时间不使用净化器，建议将其开关置于“关闭”位置。

1.5 儿童和宠物将净化器放置在儿童和宠物无法触及的位置，并确保儿童和宠物无法拆卸净化器装置和零部件。

二、保养规程2.1 滤芯更换滤芯是净化器保持好效果的核心。

在使用中，应定期更换滤芯。

在贴有指示标签的滤芯上，记录滤芯使用时间和更换日期。

更换的周期大约为8-12个月。

在使用过程中，若出现滤芯破损、变形等情况，应及时更换。

2.2 机体清洁净化器外表面有灰尘，应使用干净、软布擦拭清洁，避免使用含清洁剂或酒精的清洁液。

同时，应严禁将薄膜覆盖在机体的表面。

2.3 机体检查不定期检查机体及插头是否有明显的损坏或磨损，确保净化器正常运行。

2.4 运输在搬运净化器时，应注意避免机体受到硬物或重压的冲击。

在安装时，避免在净化器身上施加过多的压力，以免机体和配件受到损坏。

三、总结霍尼韦尔净化器是一种高科技、高性能的净化器，具有卓越的净化效果和易于操作的特点。

然而，如果用户不能正确运用和维护它，则效果和使用寿命将大大降低。

PRODUCT DATA65-0237-1CP-UM-5109E® U.S. Registered TrademarkCopyright © 2000 Honeywell Inc. • All Rights ReservedC6097A,BPressure SwitchesAPPLICATIONThe C6097 Pressure Switches are safety devices used in positive-pressure or differential-pressure systems to sense gas or air pressure changes.FEATURES•For use with natural gas, liquid propane (LP) gas, or air.•Diaphragm-actuated safety-limit switch.•Switch can be wired to turn on alarm.•C6097A models break control circuit at setpoint on pressure fall.•C6097B models break control circuit at setpoint on pressure rise.•Lockout with manual reset and recycle options.•Lockout models have external manual reset button.•Removable transparent cover protects scaleplate and adjusting knob.•Pipe tappings allow selection of positive pressure, differential pressure (air only) or venting connections (NPT mount only).•1/4 in. NPT or flange mount models for direct mounting to Honeywell Integrated Valve Train.•Optional switch position indicator lamp available.•IP54 enclosure standard.•Ranges: 0.4 to 5 in. wc, 3 to 21 in. wc, 12 to 60 in. wc or 1.5 to 7 psi.•Surge orifice.ContentsApplication ........................................................................1Features ...........................................................................1Specifications ...................................................................2Ordering Information ........................................................2Installation ........................................................................4Wiring ...............................................................................5Settings and Adjustments .................................................5Operation and Checkout ..................................................6C6097A,B PRESSURE SWITCHES65-0237—12ORDERING INFORMATIONWhen purchasing replacement and modernization products from your TRADELINE® wholesaler or distributor, refer to theTRADELINE® Catalog or price sheets for complete ordering number.If you have additional questions, need further information, or would like to comment on our products or services, please write or phone:1.Your local Home and Building Control Sales Office (check white pages of your phone directory).2.Home and Building Control Customer Logistics Honeywell Inc., 1885 Douglas Drive NorthMinneapolis, Minnesota 55422-4386 (612) 951-1000In Canada—Honeywell Limited/Honeywell Limitée, 155 Gordon Baker Road, North York, Ontario M2H 3N7.International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France, Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A.SPECIFICATIONSModels:C6097A Pressure Switch: Breaks a circuit when pressure falls to scale setting. See Table 1.C6097B Pressure Switch: Breaks a circuit when pressure rises to scale setting. See Table 1.Table 2 shows switch ratings and Table 3 shows alternate electrical ratings when used with Honeywell Flame Safeguard Programmers.Minimum Ambient Temperature: -40°F (-40°C).Maximum Ambient Temperature: 140°F (60°C).Connections (Depending on Model):1/4-18 NPT tapping for main or high-pressure connection.1/8-27 NPT tapping for vent or low-pressure connection (air only).Flange mount for connection to Honeywell Integrated Valve Train (internal vent only, no external connections).Scale Range:0.4 to 5 in. wc (0.10 kPa to 1.25 kPa).3 to 21 in. wc (0.75 to 5.23 kPa).12 to 60 in. wc (3.0 kPa to 15 kPa).1.5 to 7 psi (10.3 kPa to 48 kPa).Approvals:Underwriters Laboratories Inc. listed.Canadian Standards Association listed.Factory Mutual: Approved.Industrial Risk Insurers: Acceptable.CSD-1 AFB: Acceptable.Accessories:32003041-001 C6097 Cover for manual reset models.32003040-001 C6097 Cover for recycle models.32003039-001 Position Indication Lamp Kit.Dimensions: See Fig. 1 and 2.Fig. 1. C6097 1/4 in. NPT Mount dimensions in in. (mm).C6097A,B PRESSURE SWITCHES365-0237—1a Acceptable media: Natural gas, liquid propane (LP) gas, and air .Table 1. Pressure Switch Model Selection.Model Operating Pressure Range Manual Reset DifferentialNon-Manual ResetDifferentialDifferential Type Maximum Rated Pressure(continuous) (psi)Manual Reset Media a Switch Action at Setpoint Comments Maximumat Minimum Setpoint Maximumat MaximumSetpoint Nominal Maximum C6097A10040.4 to 5 in. wc——0.16 in. wc 0.24 in. wc Additive2.9 No Air/Gas Breaks N.O. to C.connection on pressure fall.1/4 in. NPT Mount C6097A1012 3 to 21 in. wc2.4 in. wc 4.2 in. wc —— 4.3Yes Air/Gas 1/4 in. NPT Mount C6097A1020 3 to 21 in. wc 2.4 in. wc 4.2 in. wc —— 4.3Yes Air/Gas Flange Mount C6097A103812 to 60 in. wc 10 in. wc 12 in. wc —— 4.8Yes Air/Gas 1/4 in. NPT Mount C6097A104612 to 60 in. wc10 in. wc12 in. wc—— 4.8Yes Air/Gas Flange Mount C6097A1053 3 to 21 in. wc—0.24 in. wc0.48 in. wc 4.3No Air/Gas 1/4 in. NPT Mount C6097A1061 3 to 21 in. wc ——0.24 in. wc0.48 in. wc4.3No Air/Gas Flange Mount C6097A107912 to 60 in. wc —— 1.1 in. wc 2.4 in. wc 4.8No Air/Gas 1/4 in. NPT Mount C6097A108712 to 60 in. wc—— 1.1 in. wc 2.4 in. wc 4.8No Air/Gas Flange Mount C6097A10950.4 to 5 in. wc 0.6 in. wc 1.0 in. wc —— 2.9Yes Air/Gas 1/4 in. NPT Mount C6097A1103 1.5 to 7 psi 1.1 psi 1.4 psi ——9.3Yes Air/Gas Flange Mount C6097A1111 1.5 to 7 psi 1.1 psi 1.4 psi ——9.3Yes Air/Gas 14 in. NPT Mount C6097A1129 1.5 to 7 psi ——0.1 psi 0.39.3No Air/Gas Flange Mount C6097A1137 1.5 to 7 psi——0.1 psi 0.39.3No Air/Gas 1/4 in. NPT Mount C6097A12100.4 to 5 in. wc——0.16 in. wc 0.24 in. wc 2.9No Air/Gas Flange Mount C6097A12280.4 to 5 in. wc ———— 2.9Yes Air/Gas Flange MountC6097B100212 to 60 in. wc 10 in. wc 12 in. wc ——Subtractive4.8Yes Air/Gas Breaks N.C. to C. connectionon pressure rise.1/4 in. NPT Mount C6097B101012 to 60 in. wc10 in. wc12 in. wc —— 4.8Yes Air/Gas Flange Mount C6097B1028 3 to 21 in. wc2.4 in. wc 4.2 in. wc —— 4.3Yes Air/Gas 1/4 in. NPT MountC6097B1036 3 to 21 in. wc 2.4 in. wc 4.2 in. wc —— 4.3Yes Air/Gas Flange Mount C6097B1044 1.5 to 7 psi 1.1 psi 1.4 psi ——21.0Yes Air/Gas Flange Mount C6097B1051 1.5 to 7 psi1.1 psi1.4 psi ——21.0Yes Air/Gas 1/4 in. NPT Mount C6097B1069 3 to 21 in. wc ——0.24 in. wc0.48 in. wc4.3No Air/Gas Flange Mount C6097B107712 to 60 in. wc —— 1.1 in. wc 2.4 in. wc 4.8No Air/Gas Flange Mount C6097B108512 to 60 in. wc —— 1.1 in. wc 2.4 in. wc 4.8No Air/Gas 1/4 in. NPT Mount C6097B1093 1.5 to 7 psi ——0.1 psi 0.3 psi 21.0No Air/Gas Flange Mount C6097B1101 1.5 to 7 psi——0.1 psi 0.3 psi 21.0No Air/Gas 1/4 in. NPT Mount C6097B11193 to 21 in. wc——0.24 in. wc0.48 in. wc4.3NoAir/Gas1/4 in. NPT MountC6097A,B PRESSURE SWITCHES65-0237—14Table 2. Switch Ratings (Amperes)Table 3. Alternate Electrical Ratings when used withHoneywell Flame Safeguard Programmers.Fig. 2. C6097 Flange Mount dimensions in in. (mm).INSTALLATIONWARNINGExplosion or Fire Hazard.Can cause severe personal injury, death or property damage.Observe all safety requirements each time a control is installed on a burner.When Installing this Product...1.Read these instructions carefully. Failure to follow them can damage the product or cause a hazardous condition.2.Check the ratings given in the instructions and on the product to make sure that the product is suitable for your application.3.Installer must be a trained, experienced service technician.4.After installation is completed, check out product operation as provided in these instructions.WARNINGElectrical Shock Hazard.Can cause serious personal injury or death.Disconnect power supply before beginning installation. More than one disconnection can be involved.MountingNOTE:On flange models, remove the label holding theO-ring in place and make sure O-ring seal is in place before mounting the pressure switch on the valve.The C6097 models allow NPT or flange (directly to valve) mounting. The NPT models have a hexagonal fitting with a 1/4 in. NPT tapping, which is the high pressure connection, in differential applications. The bleed fitting is 1/8 in. NPTtapped. In differential pressure control applications using air only, connect the lower pressure to the bleed fitting. See Fig. 1 and Table 1. In applications using combustible gases, vent the bleed tapping according to applicable standard code or jurisdictional authority.C6097 models with flange mount can be fitted directly toHoneywell Integrated Valve Train (model specific). See Fig. 2 and Table 1. The flange mount models vent internally, with no external tap.Mount the C6097A,B in any position.Leak CheckAfter installation, perform a leak check on the pressure switch:1.Turn on main gas. Make sure gas has reached thepressure switch (e.g., high gas pressure switch)2.Check installation for gas leaks using a gas leak detector or a soap solution.120/240 Vac, 50/60 HzInductive Full Load 3.0Locked Rotor18.0Resistive5.0DeviceRatingIgnition Transformer 540 VA Pilot Valve 50 VAMain Valve400 VA with 2-1/2 times inrush.C6097A,B PRESSURE SWITCHES565-0237—1WIRINGWARNINGElectrical Shock Hazard.Can cause serious personal injury or death.Disconnect power supply before beginning installation. More than one disconnection can be involved.Make sure that all wiring agrees with all applicable localcodes, ordinances and regulations. An opening is provided to accommodate rigid conduit or armored cable for line voltage operation (see Fig. 3 and 4). Do not overload the switch contacts (see Switch Ratings in the Specifications section). The switching schematic is shown in Fig. 5.Fig. 3. C6097 (manual reset switch model)with cover removed.Fig. 4. C6097 (recycle model) with cover removed.SETTINGS AND ADJUSTMENTSPressure Setpoint Adjustmentdial (Fig. 3, 4 and 5) clockwiseto decrease the pressure setting.Fig. 5. C6097 schematic.C6097A,B PRESSURE SWITCHES65-0237—16OPERATION AND CHECKOUTOperationThe manual reset C6097A diaphragm actuates the snap-acting switch to break a control circuit and lock out when pressure falls to the scale setting. The recycle C6097Amodels recycle automatically when the control circuit returns to scale setting plus differential.The manual reset C6097B diaphragm actuates the snap-acting switch that breaks a control circuit and locks out when the pressure rises to the scale setting. The recycle C6097B models recycle automatically when the control pressure falls to the scale setting minus differential.Manual ResettingThe C6097A manual reset models lock out when pressure falls to the scale setting and require manual resetting after the pressure rises to scale setting plus differential to resume normal operation.The C6097B manual reset models lock out when pressure rises to the scale setting and require manual resetting after the pressure falls to scale setting minus the differential to resume normal operation.To reset, once normal operating pressure is restored, push the reset button in as far as it goes, then release.IMPORTANTLockout models cannot be made to recycleautomatically by permanently holding in the reset lever.CheckoutC6097 Gas Fuel Application1.Set cutoff pressure.2.Open main supply line. Depress reset lever on lockout models until switch makes control circuit.3.Set controller and limit switch to call for heat.4.For C6097A: Close the manual gas shutoff valve. C6097 should open control circuit when pressure reaches cutoff point.For C6097B: Open the manual gas shutoff valve, wait a few minutes for the pressure to rise; then lower the scale setting until the switch breaks control circuit and locks out.5.For C6097A: Open the shutoff valve, return thepressure switch to its original setting and press the reset button (if necessary).For C6097B: raise setting to normal and press reset button (if necessary).6.Allow system to operate through at least one complete cycle to make sure all components are functioning properly.C6097A Air Application1.Set cutoff pressure.2.Turn on fan.3.Block fan inlet or filter area. Switch should break control circuit when pressure drops to cutoff point. Manual reset models lock out.4.Remove obstruction. Press reset lever (manual reset models) and allow system to operate through at least one complete cycle to be sure all components are functioning properly.765-0237—165-0237—1 G.R. Rev. 4-00Home and Building Control Home and Building ControlHoneywell Asia Pacific Inc.Honeywell Inc.Honeywell Limited-Honeywell Limitée Room 3213-3225Honeywell Plaza 155 Gordon Baker Road Sun Hung Kai Centre P.O. Box 524North York, Ontario No. 30 Harbour Road Minneapolis, MN 55408-0524M2H 3N7Wanchai Hong KongHoneywell Latin American Region Honeywell Europe S.A.480 Sawgrass Corporate Parkway 3 Avenue du Bourget Suite 2001140 Brussels Sunrise FL 33325Belgium。