FARREL FTX tm

Important Notes:Prior to beginning this or any installation read these instructions to familiarize yourself with the required steps and evaluate if you are experienced and capa-ble to personally perform these modifications.Refer to the parts list to ensure that all necessary components and hardware has been included. If any parts are missing please contact your local retailer for assistance.TeraFlex, Inc.5241 South Commerce Dr.Murray, Utah 84107Phone/801.288.2585Fax/P R O D U C T I N S T A L L A T I O N G U I D ERev. 27 August 2010 TTJK 1.5” Spring LiftPart # 1351500Required Tools:10, 14, 15, 16, 17, 18, 19, 21mm sockets and wrenches 7/16”, 5/8”, 3/4” sockets and wrenches 3/8” &1/2” drive ratchets 3”, 6”, & 12” extensions Ft-lbs torque wrench Breaker bar Floor jack Jack stands Wheel chocks Hammer Pry bars PliersSafety glassesInstallation:Remove track bar bolts using a 21mm socket, 1.at both the front and rear axle and removetrack bars.Loosen all control arm bolts using a 21mm2.socket, DO NOT REMOVE ARMS OR BOLTS!Lift the vehicle and support under the frame 3.with jack stands. Make sure that the axle willdrop far enough to remove and install the coilsprings.Remove the wheels.4.Rear Installation:Support the rear axle with a jack and slightly lift 5.one or two inches so that it is easy to removethe bolts from the shocks. (If you remove thenut from the bolt prior to jacking up on theaxle you can put slight pressure on the boltwith your hand while jacking the axle and seewhere it is easiest to remove the bolts.)Remove the bottom shock bolts using an6.18mm socket and wrench.Remove the clips that secure the ABS wiring 7.harness to the upper control arm mount.Remove the bracket that holds the park brake 8.cables to the body using a 10mm deep wellsocket.Remove the brake line mount at the frame 9.using a 10mm socket.Carefully lower the rear axle far enough to 10.remove the rear springs. Be careful not to letthe coils fall out as you lower the axle. You will want to lower the axle far enough to install thenew 1.5” springs in place. While lowering theaxle make sure the brake lines, ABS wires and axle vent do not stretch as this could causedamage to these vital parts.11.reuse the factory spring isolator.Jack up the rear axle and replace lower shock 12.bolts. Torque to 56 ft-lbs.Reinstall the brake line mount and torque to 16 13.ft-lbs.Remove jack from under axle.14.Rear installation complete.15.Front installation:Place jack under the axle and slightly lift the 16.front axle so you can easily remove factoryhardware form shocks, sway bar links.Remove the front shocks by using a 18mm 17.wrench and socket at the axle side.Remove sway bar links using 18mm socket 18.and wrench at the axle and 18mm socket and20mm wrench at the sway bar. Lower the jack enough to remove the springs.Remove front coil springs.19.Install new 1.5 inch coil springs. Do the drivers 20.side first.82225Install the new sway bar links on the outside 21.of the sway bar and inside of the axle mount.Torque to 75 ft-lbs.Reinstall the lower shock bolts and torque22.to 56 ft-lbs.Reinstall wheels, torque lug nuts to 95- 115 23.ft-lbs, Remove jack stands, lower the vehicleonto its own weight, and torque all the controlarm bolts. Torque the uppers to 75 ft-lbs andthe lowers to 125 ft-lbs.Install the rear track bar. To align the rear track 24.bar to the axle have someone push on thebody of the jeep until the bolt hole lines up.Torque to 125 ft-lbs.Install the front track bar. To align the front 25.track bar have someone move the steeringwheel until the bolt hole lines up. Torque to 125 ft-lbs.To straighten the steering wheel, loosen the 26.adjuster sleeve on the drag link by using 15mm sockets. Mark the position by making a lineacross the sleeve and the threads this line willindicate the original position. Looking from thedrivers side rotate the adjuster sleeve counterclockwise 3/4 of a turn. This should get yoursteering wheel close to center. Every vehicleis different so test drive yours and determine ifyours needs further adjustment. Once steering wheel is straight torque pinch clamp bolts to 45 ft-lbs.Re-torque all fasteners after 300 miles.27.MAINTENANCE INFORMATION:It is the buyer’s responsibility to have all suspension, drivetrain, steering, and other components checked for proper tightness and torque after the first 100 miles and every 3000 miles after that.NOTICE TO INSTALLER:The enclosed “Warning to Driver” sticker must be installed in the vehicle in driver’s view. This sticker is to act as a constant safety reminder when operating the vehicle. It is your responsibility as the equipment installer to install the provided sticker and to forward the product instructions to the vehicle’s owner for review. If a “Warning to Driver” sticker or product installation guide were not included in the kit, free replacement stickers and instructions are available by request. It is the installer’s duty to ensure a safe and controllable vehicle after the modifications have been performed.WARNING:Neither the seller nor the manufacturer will be liable for any loss, damage, or injury directly or indirectly arising from the use of or inability to determine the use of these products. Before using, the user shall determine the suitability of the products for its intended use, and the user shall assume all responsibility and risk in connection therewith.WARNING TO DRIVER:This vehicle has been modified to enhance off road performance and has unique handling characteristics. Because of the higher center of gravity and larger tires, this vehicle handles and reacts differently than many passenger cars, both on and off road. You must drive it safely! Extreme care should be taken to prevent vehicle rollover or loss of control, which can result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers. Generally, braking performance and capabilities are decreased when significantly larger/heavier tires are used, especially when used in combination with transfer case low-range reduction kits. Take this into consideration while driving. Do not add, alter or fabricate any factory or aftermarket parts to increase vehicle height over the intended height of the TeraFlex Inc. product purchased. Mixing component brand is not recommended. TeraFlex Inc. will not be responsible for any altered product or any improperinstallation or use of our products. We will be happy to answer any questions concerning the design, function, and correct use of our products. It is ultimately the buyer’s responsibility to have all bolts/nuts checked for tightness after the first 100 miles and then every 3000 miles after that. Wheel alignment, steering system, suspension and drive line systems must be inspected by a qualified professional mechanic at least every 3000 miles.TERAFLEX PRODUCT WARRANTY:TeraFlex Inc. warrants TeraFlex Suspension products to the original retail purchaser to be free of defects in material and workmanship for as long as the original purchaser owns the vehicle on which products were originally installed.Failure to complete regular maintenance (grease every 3000 miles) on TeraFlex FlexArms will void this warranty. All other conditions of the standard TeraFlex Inc. product warranty apply.All TeraLow products are covered by the TeraFlex Inc. two-year warranty to be free of defects in material and workmanship for two years from date purchased.TeraFlex axles are covered by the TeraFlex Inc. 12-month warranty to be free of defects in materials and workmanship. This warranty does not cover or include product finish, improperly installed or applied products, improperly maintained products, products or components used for racing or competition or damage due to abuse or neglect, products that fail due to the use of larger tire and wheel combinations.All returns must be accompanied by an original invoice. It is the customer’s responsibility to remove the product from the vehicle. Shipping charges are the responsibility of the customer. TeraFlex Inc. will pay the return freight.This warranty is for the replacement or repair of defective TeraFlex products only and does not include freight charges, labor charges for removal of or installation of TeraFlex or related products or components, costs incurred due to down time of the vehicle, or lost profits due to vehicle down time.A returned goods authorization number (RGA#) must accompany any returned products. For more information please contact a TeraFlex customer service representative.COPYRIGHT©Copyright 2008. All rights reserved, TeraFlex Inc. Reproduction of this catalog and/or any of its contents without writtenpermission is strictly prohibited.TeraFlex® is a registered trademark of TeraFlex Inc. All trade names and logos including but not limited to TeraFlex,FlexArms, RockGuard, Monster, and LCG are protected by law and duplication of trade names and/or logos are strictly prohibited.TeraFlex Inc. reserves the right to update, discontinue, redesign, modify finish, part number or component build parts ifdeemed necessary without written notice. TeraFlex Inc., and any associated dealers are not responsible for misprints or typographical errors that may have inadvertently been made within this instruction sheet.Jeep® and the Jeep® grill are registered trademarks of Chrysler LLC, and have no affiliation with TeraFlex Inc.PRODUCTINFORMA TION & WARRANTYTeraFlex, Inc. 5241 South Commerce Dr. Murray, Utah 84107Phone/801.288.2585 Fax/801.713.2313 。

5X OPERATING MANUALOPERATING MANUALTABLE OF CONTENTSWARNING AND TABLE OF CONTENTS (2)IMPORTANT SAFETY INFORMATION (3)SPECIFICATIONS (4)WHAT’S IN THE BOX (5)ASSEMBL Y (6)OPERATING INSTRUCTIONS (7)MAINTENANCE (10)LIMITED MANUFACTURER’S WARRANTY (11)2IMPORTANT SAFETY INFORMATIONFailure to heed these markings may result in personal injury and/or property damage:1. DO NOT use the 5X on slopes and inclines beyond stated limits.2. DO NOT submerge the 5X in water (salt or fresh) or leave it in water for prolonged periods, since this can damage the gears and erode lubricants.3. DO NOT use your drill on the 5X’s high gear. (Attachment sold separately)4. Carefully read all instructions. The operator of the 5X must exercise common sense, caution, and full judgment when assessing situations not covered or cautioned in this manual.5. The 5X is designed for specific applications only. Trailer Valet will not be responsible for issues arising from modifications made onto the device. Do not modify the device or use the device for any application other than its intended purpose. Do not exceed the designated weight limits.6. Stay alert! Do not operate if you are tired. Do not operate the device while under the influence of drugs or alcohol. Read prescription warning labels to determine if the use of prescription drugs may impair your ability to operate the device.7. As with all devices with moving parts, do not wear excessively loose clothing as it may become caught, resulting in injury. Tie back and secure long hair.8. Have a second person guide your trailer’s movements while using the 5X to avoid property damage when necessary, especially in narrow or poorly visible areas.9. Operator and bystanders should never place any part of the body under or in the path of any portion of this product or the load being supported or moved.10. This product must be installed and used in strict accordance with these instructions.11. Always remember to set the brakes before leaving or if you are having trouble maintaining control of the trailer.12. Always read and understand your drill/driver operator’s manual and instructions.13. Before each use of the 5X, check for damaged parts. Carefully inspect the device for any part that appears to be damaged to determine if the device will operate properly. Check for alignment and secure mounting of all moving parts. If the device is neither aligned, secured, or both: DO NOT use the device.14. When servicing, use only factory replacement parts.15. The 5X is not intended to be used as a transport device for the implement it is attached to.16. Have wheel blocks in place before/after use and ready in case of emergency.17. Never exceed the maximum rated capacity. Refer to the operating manual or decals on the product to obtain rated capacity. If uncertain, contact Customer Support at (844) 846-9344oremail:************************.18. The 5X is designed for vertical loading. Excessive side forces may cause failure and must be avoided.19. The use of gloves is recommended while attaching the device to the trailer.20. The 5X is designed for use on solid surfaces. DO NOT use the product on excessively soft surfaces or muddy terrain as the device will not be able to gain traction. If there is no traction despite being on a solid surface, consider shifting more of the weight of your trailer forward.SAVE THESE INSTRUCTIONS3The Trailer Valet 5X is made of high strength steel and given a powder coat finish made to resist corrosion from the elements and marine use. When cared for properly, it will provide years of service. The 5X mounts to the side of trailer tongue. Once mounted to your trailer, the 5X makes maneuvering your trailer much easier than your old jack. Hitching and unhitching, leveling, and moving is now done with precision. The 5X is designed for trailers up to 5,000 lbs. The 5X is for use only on paved surfaces or compacted gravel and soils that are free of debris.Wheel size: 9.25 inchesJack range: 14 to 22 inches Tongue max weight: 500 lbs.Trailer max weight: 5,000 lbs.Weight: 50 lbs.Maximum dimensions: 29” H x 13” L x 7.5”Patented under US Patent number 6,619,671 and 6,739,601.Phone: (844) 846-9344Email:************************Website: thank you for your purchase!Congratulations on your purchase of the T railer Valet 5X. For your future reference please complete the owner’s record below:Purchase Date: ______________________Order No.:______________________Retailer:_____________________________Be sure to save your receipt and owner’s manual with warranty information in a safe place.4SPECIFICATIONSUpon removing items from packaging, it is very important to thoroughly inspect all parts of the system before using the device. Any part that is missing or damaged must be immediately replaced.****************************************************************************14. Bracket15. Bracket Clamps 16. Bracket Bolts (x4)1. Axle Yoke Compartment2. Jack/Jack Tube3. Jack Crank4. Brake Cap5. Steering/Brake Handle6. Side Plates7. Gear Covers8. Low Gear Driveshaft 9. High Gear Driveshaft 10. Axle/ Screw Assembly 11. Rims 12. Tire13. Brake Handle Clip17. Crank Handle18. Rotation/Security Pin19. Stow/Clevis Pin & Cotter Pin 20. Security Bolt A. The Trailer Valet 5XB. Mount Bracket KitC. Accessory PackD. Cleaning Cloth5WHAT’S IN THE BOX1351748139101819151614111267220STEP 1: SET UPWhen installing the T railer Valet 5X, the unit must be installed while the weight of the trailer is supported by an existing jack.Having wheel chocks in place during connection will insure a safe install.Raise the trailer tongue to where the coupler is about 16 inches off the ground to give adequate space to attach the dolly. During installation, the Steering Handle must be secured to the safety clip to ensure the brake is engaged at all times.STEP 2: POSITIONINGThe mounting bracket has 7 holes to fit a variety of trailer frames. Be sure that you have at least 8 inches of free space for the mounting bracket to be fitted onto your trailer frame.Choose a location on the tongue frame where the 5X can freely rotate from its vertical position to its horizontal stow position.The 5X is only to be installed on trailer tongues that arerectangular in profile. Cylindrical frames are not compatible with the 5X as it will rotate, allowing the trailer to drop.STEP 3: CONNECTIONPlace the Mounting Bracket and clamps ontoIt is now recommended that you ensure that there is adequate height to install the unit. The trailer should be high enough that, when the frame is level, there is enough space for the unit to be at least one inch off the ground once attached to the bracket. If there is not enough space, adjust the placement of the bracket on your trailer frame.NOTE: While it is recommended that thebracket is installed with the attachment point in the low position for stability reasons, the bracket can be flipped prior to install if the space is required.After the bracket is positioned, evenly and firmly tighten the four bolts to secure the Mount Bracket.6ASSEMBLYUsing the Trailer Valet with the jack extended will cause excessive wear on the jack and possible result in injury and/or property damage. Always lower the Trailer tongue to its lowest position on the unit or until your trailer frame is level with the ground.STEP 5: ATTACHING DRIVEROption 1: Manual OperationAttach the Drive Handle to the low or high gear Driveshaft.The low gear drive shaft (located nearer to the top of the unit) allows greater control of the unit and may assist in moving into/through very tight spots.The high gear drive shaft (located lower on the unit) allows for greater movement tocover distance. Choose your gear accordingOption 2: Drill Adapter (sold separately)The Drill Adapter can be used with any standard 18 to 24 volt, 1⁄2 inch chuck, commercial drill. Corded drills and impact drills are not recommended.Step 4: TESTING THE ASSEMBL YRemove the rotation pin from the bottom of the jack and, if the trailer is attached to a towing vehicle, turn the crank to raise the trailer up off the hitch. Move the hitch from under your coupler.NOTE: Always ensure the operator and bystanders are aware of load stability. Remember to also disconnect any towing safety chains, the brake-turn signal wire harness, and any other connections.Raise your pre-existing trailer jack and lower the 5X unit until your trailer frame is preferably level with the ground. Y our pre-existing trailer jack should be raised until it sits at about three inches above the ground and the trailer’s weight is supported entirely by the Trailer Valet. Keep yourtrailer jack close to the ground to buffer any unexpected failures.Videos are available on the T railer Valet website if you need a visual guide to install or use your Trailer Valet.Knowing the proper techniques to operate your 5X can help keep you and others around you safe. In this guide, you are shown the basic fundamentals for effective operations. However, it is up to you to analyze the situation and make the decisions necessary for the proper use of your 5X. Apply your knowledge of your 5X and the basic fundamentals you have practiced to adjust your techniques to each unique situation.7Slot the Drill Adapter in your Drill chuck and secure tightly to avoid the adapter slipping. Align and insert the Drill Adapter to the low gear Driveshaft. Use of an electric drill is not recommended on the high gear.NOTE: If you are using a cordless drill, be sure your battery pack is fully charged before use. Follow your drill/driver manufacturer’s recommendation.NOTE: When attempting to move up any incline, it is recommended that the trailer be moved without the use of the drill adapter. Using the adapter when leading your trailer down an incline may result in damage to your drill.Visit our website to see a video on how to use your drill attachment to move your 5X.STEP 6: OPERATING THE DEVICENOTE: If your trailer has built-in brakes, theymust be disengaged prior to operation of the 5X. Consult your trailer manufacturer’s manual/ instructions on temporary brake release. If this is not available to you, please contact Trailer Valet Customer Support through phone or email for assistance.When ready to operate the device, be sure to have one hand firmly gripped on the brake/steering handle and the other hand firmly holding the drill/driver.Lift the Steering Handle until the brake is disengaged and begin cranking. TheSteering Handle must be held up firmly at all times when moving the trailer.Hold the drill firmly when engaging. Ifusing an electric drill, it will have high initial torque if the drill trigger is pulled rather than squeezed. Begin to move the trailer as slowly as capable and carefully increase the power up to an appropriate speed when using the Drill Attachment.NOTE: It is important that you steer the device only when you are cranking and the trailer is moving. Attempting to turn the Steering/Brake Handle at a dead stop will place excessive stress on a single tire which may result in damage.NOTE: When attempting to make sharp turns (E.G. 90° rotation) from a stationary position, crank the 5X back and forth while turning until the unit is in the desired position. Then, proceed to make the turn.DO NOT use the 5X on slopes and inclines exceeding a strict maximum of 10 degrees on a paved/ concrete surface. This rating is subject to factors including, but not limited to, alternate surfaces, weight distribution, change in weight capacity, and use on multi-axle trailers. If you have any questions concerning the use of your 5X on a slope or incline, please contact us at (844) 846-9344 or email us at: support@NOTE: Use of a power drill is inadvisable for movement upon any incline.When parking your trailer, slow to a gradual stop before engaging the brake. Braking with momentum may result in damage. Be sure to always engage the brake when not operating the 5X. When parked, secure with wheel chocks.8STEP 7: STORING THE DEVICE1. Remove the drill/drive handle.2. Lower your trailer’s existing jack until the T railer Valet is above the ground.3. Insert the rotation pin into the jack assembly.4. Choose between the following two options:Option 1: Remove the 5X Remove the stow pin and detach the unit from the mounting bracket. Restore theOption 2: Keep the 5X Attached to the T railerT ongueCrank the jack handle until the unit jack isfully withdrawn. Then, remove the cotterand clevis/stow pin and rotate the unit 90degrees with the “T railer Valet” logo facing up.Restore the clevis/stow and rotation pinswhile the unit remains attached to themounting bracket. This will allow the 5X toremain attached to the trailer while beingtowed.The T railer Valet 5X comes with a securitybolt (part 21) that is an option to securethe device while trailering. If you travel withthe 5X and choose to use it, the bolt slotsthrough the back of the mounting bracketand threads into the tube of the 5X jack.Failure to lock in the pinsand bolt prior to trailering with the unit inthe stow position may result in the unitbecoming dislodged during movement.9Additional Tips:• The Trailer Valet 5X is made of high strength steel and given a powder coat finish made to resist corrosion. However, if the device is used in a marine environment or where road salt is encountered, rinse off the interior and exterior with fresh water and allow to dry. DO NOT SUBMERGE THE 5X as this can damage the gears and erode lubricants.• After each use, wipe exterior surfaces with a clean cloth.10MAINTENANCELIMITED MANUFACTURER’S WARRANTYSuperT ech S Corp warrants for one year from the purchase date that the product will be in working condition and will be free from manufacturing defects, provided that installation and use of the product is in accordance with product instructions. This warranty is only made to the original consumer purchaser and is non-transferable.ALL OTHER WARRANTIES IMPLIED OR EXPRESSED ARE HEREBY DISCLAIMED.THIS WARRANTY DOES NOT COVER:1. Normal wear and tear or normal aging of the product;2. Consumable parts designed to diminish over time, unless failure occurred due to a manufacturing defect;3. Cosmetic damage, including but not limited to scratches and dents;4. Damage through accident, abuse, neglect, misuse, natural events, or other external causes;5. Damage through misapplication, overloading, or improper installation;6. Damage due to improper maintenance and repair; and/or7. Product alterations.LIMITATION OF LIABILITY:EXCEPT AS PROVIDED IN THIS WARRANTY AND TO THE MAXIMUM EXTENT PERMITTED BY LAW, SUPERTECH IS NOT RESPONSIBLE FOR ANY DIRECT, INCIDENTAL, CONSEQUENTIAL DAMAGES, OR INJURIES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION; INCLUDING, BUT NOT LIMITED TO, LOSS OF USE, LOSS OF REVENUE, LOSS OF ACTUAL OR ANTICIPATED PROFITS, LOSS OF BUSINESS, LOSS OF OPPORTUNITY, LOSS OF GOOD WILL, LOSS OF REPUTATION, OR ANY DIRECT, INDIRECT, OR CONSEQUENTIAL LOSS OR DAMAGE WHATSOEVER CAUSED, INCLUDING THE REPLACEMENT OF EQUIPMENT AND PROPERTY.CUSTOMER RESPONSIBILITIES:Customers may be required to provide proof of purchase date, respond to questions designed to assist with diagnosing potential issues, and follow Trailer Valet’s directions to make a claim on your warranty.TO MAKE A WARRANTY CLAIM:Contact us either through:PHONE: (844) 846-9344EMAIL:************************WEBSITE: TRAILER VALET SHALL HAVE THE EXCLUSIVE RIGHT TO DETERMINE IF A UNIT IS COVERED UNDER ITS LIMITED MANUFACTURER’S WARRANTY.SEVERABILITY:The invalidity, illegality, or unenforceability of any provision of this warranty shall not render the other provisions invalid, illegal, or unenforceable.GOVERNING LAW AND JURISDICTIONThis warranty shall be governed by the laws of the State of California. The courts of California shall have the exclusive right to adjudicate any disputes arising under or in connection to this warranty.11SUPERTECH S. CORP .Customer Service: (844) 846-9344Email:************************ Copyright 2022 by Supertech S. Corporation. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Supertech S. Corporation.For further information or if you have any questions, please contact:。

Fire Emblem™ FatesGetting StartedBasic InformationHow to PlayAbout Your CastleSupport InformationIMPORTANT Language Selectionsame language will be displayed in the software. If your Nintendo 3DS system is set to another language, the in-game default language will be English.For instructions about how to change the system language, please refer to the System Settings electronic manual.Age Rating InformationFor age rating information for this and other software, please consult the relevant website for the age rating system in your region.PEGI (Europe):USK (Germany):k.deClassification Operations Branch (Australia):.auOFLC (New Zealand): Russia:minsvyaz.ru/ru/documents/AdvisoriesThis software (including any digital content or documentation you download or use in connection with this software) is licensed by Nintendo only for personal and non-commercial use on your Nintendo 3DS system. Your use ofsoftware is subject to the Nintendo 3DS Service User Agreement and Privacy Policy, which includes the Nintendo 3DS Code of Conduct.Unauthorised reproduction or use is prohibited.This software contains copy protection technology to prevent reproduction and copying of content.Your Nintendo 3DS system and software are not designed for use with any existing or future unauthorised technical modification of the hardware or software or the use of any unauthorised device in connection with your Nintendo 3DS system.After the Nintendo 3DS system or any software is updated, any existing or future unauthorised technical modification of the hardware or software of your Nintendo 3DS system, or the use of any unauthorised device in connection with your Nintendo 3DS system, may render your Nintendo 3DS system permanently unplayable. Content deriving from the unauthorised technical modification of the hardware or software of your Nintendo 3DS system may be removed.This software, instruction manual and other written materialsprotected by domestic and international intellectual property laws.Trademarks are property of their respective owners. Nintendo 3DS is a trademark of Nintendo.©2015-2016 Nintendo Co., Ltd. /INTELLIGENT SYSTEMSCTR-P-BFXP-00Powered by Live2D. You can use compatible amiibo™this software.♦ If the data on your amiibo becomes corrupted and cannot berestored, go to the HOME Menu ⇒ amiibo Settings and reset the data.IMPORTANTA light touch on the Touch Screen is enough for the system to detect your amiibo. Do not press the amiibo into the screen or forcefully drag itacross the screen..m e t s y s S D 2/L X S D 3/S D 3 o d n e t n i N a h t i w o b i i m a e s u o t d e r i u q e r s i r e t i r W /r e d a e R C F N S D 3 o d n e t n i N e h T ⇒Exchanging UGCsomeone uncomfortable.- Do not infringe on the rights of others. Do not use content owned by a third party or that displays a third party (photos, images, videos) without their permission.- Do not include illegal content or any content which aids illegal activity.- Do not include any content which violates public morality.● If you post, send or otherwise Online Precautions.™k r o w t e N o d n e t n i N s t r o p p u s e r a w t f o s s i h T !e r o m h c u m d n a t n e t n o c n o -d d a w e n d a o l n w o d ,d l r o w e h t r e v o l l a s r e y a l p r e h t o h t i w y a l p o t u o y s w o l l a h c i h w e c i v r e s e n i l n o n a s i k r o w t e N o d n e t n i Nmay be allowed to see suchinformation and content. Inparticular, when choosing a user name or nickname for your Mii™characters, please do not useyour real name as others may be able to view your user name and the nicknames of your Miicharacters when using wirelesscommunication.● Friend codes are a part of asystem that allows you toestablish a friendship with other users, so that you can play,communicate and interact withpeople you know. If you exchange friend codes with strangers, there is a risk that you could receiveinformation or messages withoffensive language orinappropriate content and thatstrangers may see informationabout you that you do not wantstrangers to see. We thereforerecommend that you do not give your friend codes to people you don't know.● Do not engage in harmful, illegal,offensive or otherwiseinappropriate activity that mightcause problems for other users. In particular, do not post, send orotherwise make available anyinformation or content thatthreatens, abuses or harassesother persons, infringes on therights of others (such ascopyrights, portrait rights, privacyrights, rights of publicity ortrademarks) or that may makeother people feel uncomfortable. In particular, when sending,posting or making availablephotos, images or videosdisplaying other people, makesure to obtain their permissionbeforehand. If inappropriateconduct is reported or confirmed, you may be subject to penalties such as being banned from the Nintendo 3DS Services.● Please note that Nintendo serversmay become temporarilyunavailable without prior noticedue to maintenance following any problems, and online services for certain software may bediscontinued.the title screen, press + + simultaneously. You cannot reset your game during sl o r t n o C p a M e l t t a B sl o r t n o C n o t t u B st i n u e v i t c a n e e w t e b r o s r u c h c t i w S)d e t c e l e s t i n u e v i t c a o n (u n e M m e t s y S y a l p s i D g o l n o i t a s r e v n o c y a l p s i D no i t a m i n a r o t n e v e p i k Skc a B + ya l p s i d e u g o l a i d p u d e e p S )e u g o l a i d ( t x e N eu n i t n o C / et a g i v a NTouch the icons displayed on the Touch Screen to navigate and toggle various kinds of information.♦ If combat animations have been disabled in the Options menu,pressing and holding when engaging in combat with an enemy will display the animation.sl o r t n o C n e e r c S h c u o T tu o /n i m o o Z .t a b m o c n i g n i g a g n e n e h w d l o h d n a s s e r P n o i t a m i n a t a b m o c p i k SThe main menu will be displayed when you start the game.Select "New Game" to start the em a G w e N eu n i t n o C se d i u G e d i l S t u o b A .)s e l t t a b g n i r u d u n e M m e t s y S e h t m o rf r o ,n e e r c s s n o i t a r a p e r p e h t n og n i s s e r p y b d e s s e c c a (s n o i t p O n i m eh t g ni t a v i t c a y b y a l p s i d o t t e s e b n a c s e d i u g e h t ,s e i t l u c i f f i d r e h t o n O .y t l u c i f f i d l a m r o N n o e m a g e h t y a l p u o y n e h w t l u a f e d y b y a l p s i d o t t e s e r a s e d i u G e d i l S .s e l t t a b g n i r u d u n e M m e t s y S e h t n i "e d i u G " g n i t c e l e s y b r o ,n e e r c s s n o i t a r a p e r p e h t n o g n i s s e r p y b s e d i u G e d i l S e h t e s w o r b n a c u o Y ♦To continue a previous game, select "Continue" and then a save file to load (p. 8).♦ If you had a bookmark, it will be deleted.s a r t x EIn order to save, pre or talk to your assistant while in your There are three kinds of save file:Select "Save" from the System You can save your progress during a On the main menu, you can copy a kr a m k o o B ev a S e l t t a B ev a S l a m r o N tn e m e g a n a M a t a D at a D g n i v a S s srecovered, so be careful.♦ Save files with on the right side are saved on the SD card.From the main menu, select "Extras"and then select "Wipe Data" todelete all data.at a D l l A g n i t e l e D .l u f e r a c e b o s ,t n e n a m r e p s i n o i t a c i f i d o m y n A .a t a d e v a s f o s s o l r o s s e r g o r p o t y t i l i b a n i n a o t d a e l n a c s i h t s a ,a t a d e v a s r u o y y f i d o m o t e r a w t f o s r o s e i r o s s e c c a l a n r e t x e e s u t o n o D ●.s s o l a t a d t n e n a m r e p n i t l u s e r d l u o c s n o i t c a e s e h T .s l a n i m r e t e h t n i t r i d t e g o t t o n e r u s e k a M .g n i v a s e l i h w m e t s y s e h t o t n i d e t r e s n i d r a c D S /d r a C e m a G y n a e v o m e r t o n o D .s l o r t n o c t c e r r o c n i t u p n i y l l a n o i t n e t n i r o m e t s y s e h t t e s e r y l d e t a e p e r t o n o D ●Your castle i introduced in th game as your hom By pressin or talking to your assistant and selecting Using your Crystal Ball's StreetPass m a e T s s a P t e e r t S r u o Y g n i t i d E e l t s a C r u o Y g n i z i m o t s u C g el t s a C r u o Y d n a s g n i d l i u B g n i z i m o t s u C e e sUsing the Crystal Ball's Visit Castles option, you can connect to the Internet and visit other players'castles. You can also visit other players' castles via StreetPass (p. 11).♦ Once you've visited a castle, it will be 24 hours before you canmake the journey there again.While visiting another castle, you can give that player's avatar an accessory by talking to him or her.♦ Don't worry! You're giving the other player an exact copy ofst n e s e r P )s s a P t e e r t S / n o i t c a r e t n I e n i l n O ( s e l t s a C t i s i V )n o i t c a r e t n I e n i l n O ( a t a D g n i g n a h c x E .k c a b d e e f t n e c e r t s o m e h t e v i e c e r d n a e n i l n o s g n i t t e s e l t s a c r u o y e r a h s n a c u o y ,n o i t p o a t a D e t a d p U s 'l l a B l a t s y r C e h t g n i s U .y r o m e m s 'm e t s y s r u o y t a m r o f u o y f i r o ,m e t s y s r e h t o n a m o r f t i s s e c c a u o y f i a t a d s u o i v e r p r u o y e s u o t e l b a e b t o n l l i w u o Y ♦your accessory. You won't lose your accessories by doing this.You can change your castle's name or by talking to your assistant and selecting "Castle means that something is happening at this location.These are used to place or upgrade There are four distinct times of day: mornin afternoone e r c S e h t g n i w e i Vevening, and night. The time of day will change if you complete battles or after some time has passed.Owned Raw MaterialsThese are used for weapon forging,cooking, and wagering in the arena.You can obtain them by speaking with characters or by checking on your fields, gardens, mines,orchards, or springs.Toggling Between ScreensTouching each icon shown below will switch to the correspondingscreen.StreetPass Team Information Your Calling CardCastle Mapll a B l a t s y r C .e r o m h c u m d n a ,o b i i m a e s u ,s e l t s a c t i s i v ,a t a d r u o y e t a d p u o t n o i t a c i n u m m o c s s e l e r i w e s u n a c u o y ,l l a B l a t s y r C e h t g n i k c e h c y BObtain calling cards by selecting You can battle at your own castle or )s s a P t e e r t S (se l t t a B e l t s a C )s s a P t e e r t S (s d r a C g n i l l a C e g n a h c x E dr a C g n i l l a C r u o Y g n i t i d E ."d r a C t i d E " g n i t c e l e s d n a l l a B l a t s y r C e h t f o u n e m m a e T s s a P t e e r t S e h t o t g n i o g y b d r a c g n i l l a c r u o y f o t n e t n o c e h t e g n a h C ,e r a w t f o s s i h t r o f d e l b a n e s s a P t e e r t S h t i w s m e t s y s S D 3 o d n e t n i N g n i y r r a c e l p o e p r e h t o y b s s a p u o y n e h Wyou may get a special bonus, such as being able to select one of your opponent's characters to add toyour Unit Logbook.♦ You can also deactivate StreetPass for this software by going to the HOME Menu ⇒System Settings ⇒ Data Management and deleting its StreetPass data. If you wish t .l l a B l a t s y r C e h t m o r f t i e t a v i t c a e s a e l p ,n i a g a s s a P t e e r t S e t a v i t c a o ss a P t e e r t S g n i t a v i t c A .d e v a s s i e m a g e h t e m i t h c a e a t a d s s a P t e e r t S e t a d p u l l i w g n i v a s c i t a m o t u a g n i l b a n E .a t a d s s a P t e e r t S f o g n i v a s c i t a m o t u a e l b a s i d /e l b a n e d n a s s a P t e e r t S e t a v i t c a e d /e t a v i t c a o t o f n I /s g n i t t e S r e d n u s s a P t e e r t S o t o g n a c u o y ,s i h t o d u o y r e t f A .e l t s a c r u o y n i l l a B l a t s y r C e h t e s u ,e r a w t f o s s i h t r o f s s a P t e e r t S e t a v i t c a o TCheck the data you receive from While the system is in Sleep Mode,ss a P t o p S g n i t a v i t c A .s s a P t o p S e t a v i t c a e d r o e t a v i t c a o t l l a B l a t s y r C e h t m o r f o f n I /s g n i t t e S n i "s s a P t o p S " t c e l e S ."s s a P t o p S " g n i t c e l e s n e h t d n a ,"s a r t x E " g n i t c e l e s ,u n e m n i a m e h t o t g n i o g y b s s a P t o p S e t a v i t c a o s l a n a c u o Y ♦)™s s a P t o p S (sn o i t a u l a v E d n a s t n e s e r P g n i v i e c e R at a D e l t s a C d e v i e c e R g n i k c e h C- One Nintendo 3DS system per From the Crystal Ball menu, select ● Joining a session.h t i w t c a r e t n i o t r e y a l p e h t t c e l e s o t "n o i s s e S n i o J " t c e l e S pu t e S )y a l P l a c o L ( s r e y a l P r e h t O h t i w g n i t c a r e t n I :d e e N l l i W u o Y- One Nintendo 3DS system per From the main menu, select Connect to the Internet and battle )n o i t c a r e t n I en i l n O ( e l t t a B t e n r e t n I pu t e S )y a l P l a c o L ( e l t t a B l a c o L :d e e N l l i W u o Ymenu and selecting "Extras", then "Wireless Battle", and then "Internet Battle".You can choose to battle a friend or a random opponent. Once an opponent has been found, you must select your units and set some rulesbefore the battle will begin.se l t t a B s s e l e r i W n i d e s U s m a e T :g n i w o l l o f e h t g n i o d y b m a e t a r e t s i g e R .d e r e t s i g e r m a e t e n o t s a e l t a e v a h u o y s s e l n u e l t t a B t e n r e t n I r o e l t t a B l a c o L e s o o h c t o n n a c u o Y ."m a e T e t a e r C " n e h t d n a ,"e l t t a B s s e l e r i W " n e h t ,"s a r t x E " t c e l e s d n a u n e m n i a m e h t o t o G .1.e s u o t e l if e v a s e h t t c e l e s ,m a e t r u o yg n i s o oh c r e t f A .2.m a e t e h t r e t s i g e r o t "K O "t c e l e s ,d e h s i n i f e r 'u o y n e h W .s l l i k s p i u q e n u r o p i u q e d n a ,s m e t i r i e h t e z i n a g r o ,y o l p e d o t s r e t c a r a h c e h t e n i m r e t e D .3This game allows you to purchase New paths can be purchased by 1. To purchase DLC, go to the CL D g n i s a h c r u P es a h c r u P o t w o H )n o i t c a r e t n I en i l n O ( t n e t n o C e l b a d a o l n w o D g n i s a h c r u P s h t a P l a n o i t i d d A g n i s a h c r u PTo purchase DLC, you must have the required funds in your Nintendo eShop account balance. If you do not have the required funds, you will be prompted to add funds. Select "Add Funds" to proceed.You will need a Nintendo eShop Card, Nintendo eShop activationcode or credit card to add funds.4. Select "Purchase", and the download will begin.♦ Credit card details can be saved so that it is not necessary toCL D g n i s a h c r u P t u o b A .e e r f r o f d e d a o l n w o d -e r e b n a c C L D ,d e s a h c r u p e c n O ●.p o h S e o d n e t n i N f o n o i t c e s y t i v i t c A t n u o c c A e h t n i C L D d e s a h c r u p r u o y k c e h c n a c u o Y ●.m e t s y s t a h t n o e l b a l i a v a e b t o n l l i w d e s a h c r u p e v a h u o y s m e t i ,m e t s y s r e h t o n a o t n i d r a c D S e h t t r e s n i u o y f I .t i e s a h c r u p o t d e s u m e t s y s S D 3 o d n e t n i N e h t h t i w e l b i t a p m o c y l n o s i C L D d e s a h c r u P ●.d r a c D S e h t o t d e v a s e b l l i w C L D d e s a h c r u P ●sd n u F g n i d d Aenter them every time funds are added.♦ Saved credit card details can be removed at any time throug .p o h S e o d n e t n i N n i "r e h t O /s g n i t t e S "h。

FLAT-PAK ™ SERIESModel FP-TPX3AFormat-A Twisted Pair Remote Controlled Mixer∙ 3-Channel Remote-Controlled Audio Mixer ∙ VCA Level Control for Each Input Pair ∙ Format-A Twisted Pair Inputs∙ Balanced and Unbalanced Outputs∙ Two Mono Unbalanced Outputs to Feed Stereo Amplifier ∙ Inputs and Outputs on Detachable Connectors ∙ Twisted Pair Interconnection to Remote Control ∙ Directly Controlled by RDL Remote Controls∙ Two and Three Channel Remote Controls Available∙ Local Input Available if Only Two Twisted Pair Inputs Used ∙ Paging Source May Connect to Local Input∙ Front-Panel Gain Trim Matches Active or Passive Format-A Senders ∙ Dual-LED VU Meter Displays Mixer Output Level ∙ Audio Presence Detector Controls Open-Collector Outputs ∙ Detector Outputs Intended to Enable Power Amplifiers or System Power∙ Energy Savings Possible Using Detector Outputs∙Selectable 10 or 20 Minute Detector Release DelayThe FP-TPX3A is a mono audio mixer in the convenient line of FLAT-PAK products, featuring the superior engineering and components common to RDL products. The FP-TPX3A may be rack or surface mounted with optional FLAT-PAK series accessories. The FP-TPX3A gives you the advantages of a quality audio mixer with the added convenience of remote control!The FP-TPX3A is the ideal choice where a user-accessible mixer must control the volume of multiple sources in a zone. RDL Format-A twisted pair audio senders connect directly to the mixer, allowing each user input to be balanced or unbalanced, mic or line level. FP-TPX3A outputs are provided in balanced and unbalanced formats. Two unbalanced outputs are available to feed the mono mixer output to a stereo amplifier input. Remote control of the mixer allows audio signals to be kept at a single equipment location. Audio is mixed by VCA circuits that are adjusted by control signals from the remote control.Two Format-A jacks are provided for signal inputs. If the Format-A senders are daisy-chained, only one of the input jacks is used. The other input jack may be used to receive another Format-A sender, or may be used to loop the received Format-A signals out to additional Format-A mixers or receivers. The FP-TPX3A provides power to all connected active senders. The FP-TPX3A is designed to mix the three Format-A audio signals from pairs A, B and C. A front-panel switch allows the PAIR C mixer input to be fed either from the twisted pair C input signal or from a local input. A detachable terminal block is provided to connect a local paging or music source to the LOCAL INPUT . Note: Pair C signals are passed through both Format-A input jacks even if the mixer is set to use a local source instead of the PAIR C twisted pair source.Format-A senders are available in active and passive models. Passive Format-A models with unbalanced input jacks send a lower signal level to the mixer than is sent by active senders or by passive senders with balanced inputs. Each INPUT GAIN control is calibrated to be adjusted clockwise for an unbalanced passive sender; counter-clockwise for an active sender or passive sender with a balanced input. A standard RDL dual-LED VU meter provides visual indication of the output level from the mixer. Each input channel operates at unity gain when the corresponding remote control is adjusted to maximum. This assures ample headroom at all normal operating levels. The mixer output is mono. The output is available on a single balanced detachable terminal block or on two unbalanced RCA jacks intended to connect directly to the stereo input of a power amplifier.The AUDIO LED illuminates whenever audio is present at the output of the mixer, defined as greater than 35 dB below +4 dBu. This threshold triggers the AUDIO DETECT OUTPUTS . Two open collectors are provided on a detachable terminal block. One of these terminals switches low when audio is present, and may be used to switch amplifiers or other system components on. The other terminal is pulled low when audio is not present. It is intended for muting the digital carrier of power amplifiers equipped for remote muting. Either of these terminals may be used to trigger a variety of other RDL modules or OEM equipment. The use of these terminals to shut down unused equipment can produce effective system energy and cost savings. These control terminals normally remain triggered for 10 minutes after audio is absent. The delay can be increased to 20 minutes using a ground jumper on the terminal block.The mixer levels are set by RDL remote controls that connect directly to the FP-TPX3 through an RJ45 jack using standard twisted pair cable. The control ports on the mixer and remote controls are color-coded light blue to distinguish them from standard Format-A jacks. The mixer provides power to the remote control. Either a two or three channel remote control may be used. If remote mixing of only two channels is needed, a two channel remote may be used. Pair C becomes the input channel that is not remotely controlled. The PAIR C /LOCAL INPUT can be left active at unity gain, typically for a paging source, or may be disabled by a switch set during installation. If the cable connected to the remote control becomes disconnected, the mixer output mutes.RDL ∙ 659 6th St. ∙ Prescott, AZ., USA 86301 ∙ (928) 443-9391 ∙ FAX (928) 443-9392 ∙ TYPICAL APPLICATIONS:► Meeting Rooms ► Boardrooms ► Classrooms► Restaurant or Residential Patios ► Retail Stores ASSOCIATED REMOTE CONTROL EXAMPLES: ► D-RC2 and DS-RC2 Two-channel remote controls ► D-RC2M and DS-RC2M Two-channel remote controls with muting► D-RC3 and DS-RC3 Three-channel remote controls ► D-RC3M and DS-RC3M Three-channel remote controls with mutingFLAT-PAK ™SERIESModel FP-TPX3AFormat-A Twisted Pair Remote Controlled MixerTYPICAL PERFORMANCEInputs (3): RDL FORMAT-A; Balanced line levelInput Connections: RJ45 (FORMAT-A); Detachable Terminal Block (Pair C) Outputs (3): 150 Ω balanced; 1 k Ω unbalanced (2)Output Connections: Detachable Terminal Block (balanced); RCA Phono Jacks (unbalanced) Output Level: +4 dBu balanced, -10 dBV unbalanced Frequency Response: 20 Hz to 20 kHz (+/- 0.25 dB)THD+N: < 0.05% (20 Hz to 20 kHz); <0.02% (1 kHz)Noise below +4 dBu: < -100 dB (all channels off); <-75 dB (any channel on); <-70 dB (all channels on) Headroom above +4 dBu: > 18 dBCMRR: > 80 dB (50 Hz to 150 Hz)VCA attenuation: >90 dB (each input, remote control volume off)Indicators (3): Dual-LED VU meter (2); Audio present (threshold = 35 dB below +4 dBu output) Power Connections (3): Terminal block; dc power jack (2)Power Requirement: 24 Vdc @ 120 mA plus connected FORMAT-A sender currents Overall Dimensions: Height: 1.42 in.3.61 cm Width: 3.25 in. 8.26 cmLength: 8.14 in. 20.68 cmInstallation/OperationDeclaration of Conformity available from . Specifications are subject to change without notice.Radio Design Labs Technical Support CentersU.S.A. (800) 933-1780, (928) 778-3554; Fax: (928) 778-3506Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287891-2145E。

amaran F22x Product ManualEnglishForewordThank you for purchasing "amaran" LED photography lights - amaran F22x.Amaran F22x is amaran newly designed cost performance light fixture. Compact structure design, compact and light, excellent texture.Has a high performance level, such as high brightness, high color render-ing index, can adjust the brightness, etc. It can be used with variety of lighting accessories to achieve lighting effects and enrich product usage patterns. So that the product to meet the needs of different occasions light control, easy to achieve professional level photography. IMPORTANT SAFETY INSTRUCTIONSWhen using this unit, basic safety precautions should always be followed, including the following:1. Read and understand all instructions before using.2. Close supervision is necessary when any fixture is used by or near children. Do not leave the fixture unattended while in use.3. Care must be taken as burns can occur from touching hot surfaces.4. Do not operate the fixture if a cord is damaged, or if the fixture has been dropped or damaged, until it has been examined by qualified service personnel.5. Position any power cables such that they will not be tripped over, pulled, or put into contact with hot surfaces.6. If an extension cord is necessary, a cord with an amperage rating at least equal to that of the fixture should be used. Cords rated for less amperage than the fixture may overheat.7. Always unplug the lighting fixture from the electrical outlet before cleaning and servicing, or when not in use. Never yank the cord to remove the plug from the outlet.8. Let the lighting fixture cool completely before storing. Unplug the power cable from lighting fixture before storing and store the cable at assigned space of thecarrying case.9. To reduce the risk of electric shock, do not immerse this fixture in water or any other liquids.10. To reduce the risk of fire or electric shock, do not disassemble this fi********************************************fixturetoqualified service personnel when service or repair is required. Incorrect reassem-bly may cause electric shock when the lighting fixture is in use.11. The use of any accessory attachment not recommended by the manufacturer may increase the risk of fire, electric shock, or injury to any persons operating the fixture.12. Please power this fixture by connecting it to a grounded outlet.13. Please do not block the ventilation or do not look atPlease do not touch the LED light source in any condition.object.15. Only use a dry microfiber cloth to clean the product.16. Please do not use the light fixture in wet condition on account of electric shock may be caused.17. Please have the product checked by an authorized service person-nel agent if the product has a problem. Any malfunctions caused by unauthorized disassembly are not covered by the warranty. The user may pay for maintenance.18. We recommend only using the original Aputure cable accessories. Please note that any malfunctions caused by using unauthorized accessories are not covered by the warranty. The user may pay for maintenance.19. This product is certified by RoHS, CE, KC, PSE, and FCC. Please operate the product in full compliance with relevant country's standards. Any malfunctions caused by incorrect use are not covered by warranty. The user may pay for maintenance.20. The instructions and information in this manual are based on thorough, controlled company testing procedures. Further notice will not be given if the design or specifications change.SAVE THESE INSTRUCTIONSFCC Compliance StatementThis device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may cause undesired operation.Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferencein a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.Connect the equipment to an outlet on a different circuit than the receiveris connected to. Consult the dealer or an experienced radio/TV technician for help. This device has been evaluated to meet general RF exposure require-Extension Cable(1 pc)Soft Box (1 pc)45°Grid (1 pc)Fabric Diffusion 1 (1 pc)Fabric Diffusion 2 (1 pc)Carry Case (1 pc)AC Cable (1 pc)Bracket A(1 pc)Bracket B(1 pc) Power Adapter (1 pc)Control Box(1 pc)Frame (1 pc)Tie Down (1 pc) Components ListPlease make sure all accessories listed below are completed before using. If not, please contact with your sellers immediately.(*Anton Bauer orV-mount)Tips: The illustrations in the manual are only diagrams for reference. Due to the continuous development of new versions of the product, if there are any differences between the productand the user manual diagrams, please refer to the product itself.Frame Mounting CornerVelcroComponents List1. Lamp HeadDC IN2. Control BoxSetting Up the LightFront of the frameBack of the frame1. Disassembly and assembly of X-type frame. After pulling out the bolts in the direction shown in the picture, unfold the four support rods, and then loosen the fixing bolts to lock the support rods.2.Disassembly and assembly of the lamp body and X-shaped bracket. Insert the four support rods into the blocks at the four corners of the lamp body in turn. When removing, pull out the four support rods in turn in the opposite direction.3.Installation of soft box.Powering up the Light Powered by ACPowered by DCOperationsHow to use the extension cord1.Turning on the Light*The battery is not standard.*When removing the wire, because of self-locking device at the wire connection, please press or rotate the spring lock on the connector before pulling it out. Do not pull it out forcibly.*Extension cable, control box and lamp body need to correspond, and different models cannot be mixed.2.2.2 Press the INT button to select FX mode, then rotate the INT control knob to toggle between Paparazzi , Lightning , TV ,Fire , Strobe ,Explosion ,Fault Bulb , Pulsing ,Fireworks.2.1 Press the Light Mode button to enter the interface2.2.1 Press the INT knob, select CCT mode to adjust color temperature (2500K~7500K)， brightness (0%~100%) .*Under Lightning and Explosion effects, press the TRIGGER knob, will trigger the effects ; under other effects press the INT TRIGGER to circulate or stop the effects.2.2.3 Press the INT knob, after selecting the CFX mode, Rotate the INT knob to select the Picker FX, Music FX, and TouchBar FX.2.3 Press the MENU button to enter MENU, as shown in the figure below.2.3.1 DMX ModePress the INT knob to enter the DMX mode, and rotate the INT knob to adjust the DMX channel (001~512).2.3.2 Frequency SelectionPress the INT knob to enter the Frequency Selection, Rotate the INT knob to select the frequency (+0~2000Hz).2.3.3 Dimming CurvePress the INT knob to enter the dimming curve menu, rotate the INT knob to select “Exp; Log; S-curve; Linear”Dimming curve, then press the INT knob to confirm theselection.2.3.4 BT ResetPress the INT knob to enter the BT Reset, rotate the INT knob to select "Yes", press the INT knob to reset the Bluetooth; select "No" to return to the main menu.2.3.5 BT Serial NO.Rotate the INT knob to select the BT serial NO, press the INT knob to enter the BT serial NO. interface to display the Bluetooth serial number2.3.6 Studio ModeRotate the INT knob to select the studio mode, press the INT knob to enter the studio mode interface, rotate the INT knob to select "Yes" or "No", and then short press the INT knob to confirm.2.3.7 LanguageRotate the INT knob to select the language menu, press the INT knob to enter the language setting interface, rotate the INT knob to select "English" or "Chinese", and then press the INT knob to confirm.2.3.8 Firmware VersionRotate the INT knob to select the Firmware Version, press the INT knob to enter thefirmware version interface, short press the INT knob again to return to the main menu.2.3.9 Update FirmwareRotate the INT knob to select Update Firmware, short press the INT knob to enter thefirmware upgrade interface, rotate the INT knob to select "Yes" or "No", and then press the INT knob to confirm.2.3.10 Factory ResetRotate the INT knob to select Factory Reset, press the INT knob to enter the Factory Reset interface, rotate the INT knob to select "Yes" or "No", and then press the INT knob to confirm.3.DMX Control3.1 Connecting Type-c to DMX adapter to controller3.2 Connect a standard DMX controller4. Using the Sidus Link APPYou can download the Sidus Link app from the iOS App Store or Google Play Store for enhancing the functionality of the light. Please visit sidus.link/app/help for more details regarding how to use the app to control your Aputure lights.3.4 DMX Channel SelectionIn DMX mode, match the channel of your DMX controller with the light, and then control the light via DMX controller.Sidus.link/app/helpGet Sidus Link App5. SpecificationsPhotometrics≥9812～28.8VCRIDistance (m)Illuminance (lux)Bare BulbSoftbox (1/2 stop )Bare BulbSoftbox (1/2 stop )Bare BulbSoftbox (1/2 stop )Bare BulbSoftbox (1/2 stop )0.5m 1m 3m 5m 2500KCCT3200K4300K5600K2500K~7500K Power Output Power Input 48V200W (Max)≥95240W (Max)V-Mount batteryV-mount battery compatibility 16.8V battery half output;26V,28.8V battery full output.Power adapter outputOLED Display Cooling ModeManual, Sidus Link APP, DMX Light fixture Natural heat dissipation ControllerActive coolingControlling method ≤ 80m / 262.5ft ，2.4G Hz Remote control distance(Bluetooth)CCT TLCI Voltage5A (Max)Operating Temperature -10°C ~ 40°C48VPower SupplyOperating Current 194005710689260115403750486190199306050706280124403940512200217106500770294131204210543215232706960824317140404510582232TrademarksBowens is a trademark registered by Bowens in China and other countries.* These are average data measured in the laboratory, there will be slight differences in thebrightness, color temperature and other parameters of different lights.You can find a detailed user guide for this device on our website .Bare BulbSoftbox (1/2 stop )Bare Bulb Softbox (1/2 stop )6500K7500K244707200836331147704690619241250307510886344151204860626251。

Identity Number K1.0024074Model ALEXA Mini LFSensor Type Large Format ARRI ALEV III (A2X) CMOS sensor with Bayer pattern colorfilter arraySensor Maximum Resolution and Size4448 x 309636.70 x 25.54 mm / 1.444 x 1.005"⌀ 44.71 mm / 1.760"Sensor Frame Rates0.75 - 90 fpsWeight∼2.6 kg / ∼5.7 lbs(camera body with LPL lens mount)800 g (MVF-2)Photosite Pitch8.25 μmSensor Active Image Area Photosites LF Open Gate ProRes 4.5K: 4448 x 3096LF Open Gate ARRIRAW 4.5K: 4448 x 3096LF 16:9 ProRes HD: 3840 x 2160LF 16:9 ProRes 2K: 3840 x 2160LF 16:9 ProRes UHD: 3840 x 2160LF 16:9 ARRIRAW UHD: 3840 x 2160LF 2.39:1 ProRes 4.5K: 4448 x 1856LF 2.39:1 ARRIRAW 4.5K: 4448 x 1856Sensor Active Image Area Dimensions LF Open Gate ProRes 4.5K: 36.70 x 25.54 mm / 1.445 x 1.006"LF Open Gate ARRIRAW 4.5K: 36.70 x 25.54 mm / 1.445 x 1.006"LF 16:9 ProRes HD: 31.68 x 17.82 mm / 1.247 x 0.702"LF 16:9 ProRes 2K: 31.68 x 17.82 mm / 1.247 x 0.702"LF 16:9 ProRes UHD: 31.68 x 17.82 mm / 1.247 x 0.702"LF 16:9 ARRIRAW UHD: 31.68 x 17.82 mm / 1.247 x 0.702"LF 2.39:1 ProRes 4.5K: 36.70 x 15.31 mm / 1.445 x 0.603"LF 2.39:1 ARRIRAW 4.5K: 36.70 x 15.31 mm / 1.445 x 0.603" Recording File Container Size LF Open Gate ProRes 4.5K: 4480 x 3096LF Open Gate ARRIRAW 4.5K: 4448 x 3096LF 16:9 ProRes HD: 1920 x 1080LF 16:9 ProRes 2K: 2048 x 1152LF 16:9 ProRes UHD: 3840 x 2160LF 16:9 ARRIRAW UHD: 3840 x 2160LF 2.39:1 ProRes 4.5K: 4480 x 1856LF 2.39:1 ARRIRAW 4.5K: 4448 x 1856Recording File Image Content LF Open Gate ProRes 4.5K: 4448 x 3096LF Open Gate ARRIRAW 4.5K: 4448 x 3096LF 16:9 ProRes HD: 1920 x 1080LF 16:9 ProRes 2K: 2048 x 1152LF 16:9 ProRes UHD: 3840 x 2160LF 16:9 ARRIRAW UHD: 3840 x 2160LF 2.39:1 ProRes 4.5K: 4448 x 1856LF 2.39:1 ARRIRAW 4.5K: 4448 x 1856Exposure Latitude14+ stops over the entire sensitivity range from EI 160 to EI 3200 asmeasured with the ARRI Dynamic Range Test Chart (DRTC-1) Exposure Index Adjustable from EI 160-3200 in 1/3 stopsEI 800 base sensitivityShutter Electronic shutter, 5.0°- 356° or 1s - 1/8000sRecording Formats MXF/ARRIRAWMXF/Apple ProRes 4444 XQMXF/Apple ProRes 4444MXF/Apple ProRes 422 HQRecording Media Codex Compact DrivesRecording Frame Rates LF Open Gate ProRes 4.5K: 0.75 - 40 fpsLF Open Gate ARRIRAW 4.5K: 0.75 - 40 fpsLF 16:9 ProRes HD: 0.75 - 90 fpsLF 16:9 ProRes 2K: 0.75 - 90 fpsLF 16:9 ProRes UHD: 0.75 - 60 fpsLF 16:9 ARRIRAW UHD: 0.75 - 60 fpsLF 2.39:1 ProRes 4.5K: 0.75 - 60 fpsLF 2.39:1 ARRIRAW 4.5K: 0.75 - 60 fpsNote: maximum fps values are preliminary informationRecording Modes Standard real-time recordingNo Pre-recordingNo IntervalometerViewfinder Type Multi Viewfinder MVF-2 with 4" flip-out monitorViewfinder Technology OLED viewfinder displayLCD fold out monitorViewfinder Resolution Pixel1920 x 1080Viewfinder Diopter Adjustable from -5 to +5 dioptersColor Output Rec 709Rec 2020Log CCustom Look (ARRI Look File ALF-2)Look Control Import of custom 3D LUTASC CDL parameters (slope, offset, power, saturation)White Balance Manual and auto white balance, adjustable from 2000K to 11000K in 10KstepsColor correction adjustable range from -16 to +16 CC1 CC corresponds to 035 Kodak CC values or 1/8 Rosco valuesFilters Built-in motorized ND filters 0.6, 1.2, 1.8Fixed optical low pass, UV, IR filterImage Outputs 1x proprietary signal output for MVF-2 viewfinder on VF CoaXPressconnector (video, audio, power, control signals)SDI 1:-HD only, Processed or Clean, with or without a look file applied-1.5G 422 HD (SMPTE ST292-1, up to 30 fps, progessive (p) or progressivesegmented frame (psf))-3G 422 HD (SMPTE ST425-1, up to 60 fps, p)-3G 444 HD (SMPTE ST425-3, up to 30 fps, p)SDI 2:-HD or UHD, Clean only, with or without a look file applied, or SDI 1 clone-1.5G 422 HD (SMPTE ST292-1, up to 30 fps, p or psf)-3G 422 HD (SMPTE ST425-1, up to 60 fps, p)-3G 444 HD (SMPTE ST425-3, up to 30 fps, p)-6G 422 UHD (SMPTE ST2081-10, up to 30 fps, p)“Clean” is an image without surround view or overlays (status, false color,zebra, framelines, etc.)“Processed” is an image with surround view or overlays.Lens Squeeze Factors 1.001.251.301.501.651.802.00Exposure and Focus Tools False ColorZebraZoomAperture and Color PeakingAudio Input1x LEMO 6pin balanced stereo line in with 12V power output(Line input max. level +24dBu correlating to 0dBFS)Audio Output SDI (embedded)3,5mm stereo headphone jack (on MVF-2)Audio Recording 2 channel linear PCM, 24 bit 48 kHzRemote Control Options MVF-2 viewfinder can act as wired remote control with 10m/33ft cableWeb-based remote control from smart phones, tablets and laptops viaWiFi & Ethernet (beta version)Camera Access Protocol (CAP) via Ethernet & WiFiGPIO interface for integration with custom control interfacesWCU-4 hand-unit with control over lens motors and operationalparameters via built-in white radioSXU-1 hand-unit with control over one lens channelOCU-1 and Master Grip control of lens and user buttonsInterfaces1x LEMO 5pin LTC Timecode In/Out1x LEMO 10pin Ethernet for remote control and service1x BNC SYNC IN1x LEMO 7pin EXT multi purpose accessory interface w. RS pin and 24Vpower output1x LEMO 4pin LBUS (on lens mount) for lens motors, daisy chainable1x USB 2.0 in media bay (for user setups, look files etc)Wireless Interfaces Built-in WiFi module (IEEE 802.11b/g)Built-in White Radio for ARRI lens and camera remote controlLens Mounts LPL lens mount with LBUS connectorPL-to-LPL adapterLeitz M mount (available from Leitz)Flange Focal Depth LPL mount: 44 mmwith PL-to-LPL adapter: 52 mmPower Input1x LEMO 8pin (11-34 V DC)Power Consumption Around 65 W when recording ARRIRAW at 24 fps with MVF-2 attached(preliminary information)Power Outputs 1x Fischer 3pin 24V RS1x LEMO 2pin 12V1x LEMO 7pin EXT 24V power outputPower Management-Measurements HxWxL140 x 143 x 188 mm / 5.5 x 5.6 x 7.4"(camera body with LPL lens mount)Operating Temperature-20° C to +45° C / -4° F to +113° F @ 95% relative humidity max, noncondensing, splash and dust proof through sealed electronics Storage Temperature-30° C to +70° C / -22° F to +158° FSound Level< 20 dB(A) at 24fpsSoftware Licenses-。

Register at .Original Instructions(EN)*3441-881*AOrdering Replacement PartsTo order replacement parts,please supply the part number, the quantity,and the description of each part desired. Understanding Reference NumbersEach identified part in an illustration has a reference number.The reference number for a part also appears in the parts list,along with other information about the part. This catalog uses two special reference number formats, one to indicate parts in a service assembly and another to indicate the quantity of a given part in an illustration. Service Assembly Reference NumbersParts in service assemblies have reference numbers in the form a:b.The a represents the reference number of the entire service assembly and the b represents a sequential number unique to each part within the service assembly.For example,a wheel assembly might be identified byreference number6,the tire by6:1,the valve by6:2,and the wheel by6:3.When you order the assembly identified by reference number6,you receive all parts identified by reference numbers6:1,6:2,and6:3.However,you may also order any part individually.Reference numbers of this type appear in illustration and in parts lists.Reference Numbers Indicating QuantityIn an illustration,if a reference number indicates more than one part,the reference number has the form nX y.The n represents the quantity of the part,the X is the multiplication symbol,and the y represents the reference number.For example,in an illustration,the reference number2X37 means that two of the parts identified by reference number 37are indicated.2ContentsFrame Assembly (4)Deck Lift Assembly (6)Caster,Wheel and Tire Assembly (8)Traction Drive Assembly (10)LH Transaxle Assembly No.139-7470 (12)RH Transaxle Assembly No.139-7471 (14)Brake Assembly (16)Rear Tire Assembly (18)Motion Control Assembly (20)Engine and Muffler Assembly (22)Fuel System Assembly (24)Carburetor Assembly (26)Air Intake and Filtration Assembly (28)Ignition and Cooling Fan Assembly (30)Crankcase and Crankshaft Assembly (32)Governor Control Assembly (34)Piston and Cylinder Head Assembly (36)Blower Housing Assembly (38)Gasket and Seal Kit (40)Fuel Pod Assembly (42)Electrical Assembly (44)54in Deck and Decal Assembly (46)Frame Decal Assembly (48)Seat Pan Assembly (50)Seat Assembly No.140-8303 (52)Clutch Assembly (54)Attachments and Accessories (56)©2020—The Toro®Company8111Lyndale Avenue SouthBloomington,MN554203Contact us at .Printed in the USA.All Rights ReservedFrame Assembly3441-881A4A0Frame Assembly(continued)Ref.Part Number Qty.Description1137-9820-011Frame Assembly3138-7520-011Plate-Mount,Hydro4139-2352-011Plate-Mount Hydro,RH 5137-7020-011Mount-Hydro,Front(Right) 6139-3211-011Mount-Hydro,Front(Left) 7138-2527-011Brace-Cross,Lower8139-3260-011Bracket-Mount Damper,Lower9138-0867-031Guard-Muffler12138-9820-031Guard-Engine14138-7596-011Footrest15140-20972Axle Stub ASM15:2109-36782Bearing-Ball17138-72002Cap-GreaseRef.Part Number Qty.Description18117-1232-031Bracket-Hitch19138-75162Guard-Rail20139-58901Decal-Timecutter21139-23871Decal-Timecutter22121-29892Decal-Bypass23137-48032Bumper-Rubber24140-34602Bumper-Rubber26138-975320Screw27139-24294Screw-HHF283234-2914Screw-HHF30139-24284Screw-HWH3146-80914Screw-HWH32139-24304Nut-HF,NI33104-830016Nut-HF,NI53441-881ADeck Lift Assembly3441-881A6B0Deck Lift Assembly(continued)Ref.Part Number Qty.Description1137-7093-031Deck Lift ASM2138-60212Bracket-Pivot,Decklift 3137-98441LH Arm ASM4137-98461RH Arm ASM5139-2350-011Bracket-HOC6138-60062Plate-HOC Adjustment 7137-7087-031Lever-Lift8138-60501Rod-Mount,Deck 9119-88101Pin-Pivot10138-2549-031Pedal-Lift11137-70861Plate-Footlift12140-2746-031Link ASM13140-34612Spacer141-8060057Pin-Cotter15138-97535ScrewRef.Part Number Qty.Description18137-98474Screw-Shoulder2093-88063Washer-Hardened213256-267Washer-Flat2263-22902Washer-Thrust23104-83002Nut-HF,NI24104-83015Nut-HF,NI253296-191Nut-Hex26139-23921Decal-HOC271-6332681Grip-Lever30120-22731Washer-Nylon31139-74521Pedal-Foot Lift32140-20931Spacer33139-25901Screw-CARR343230-32Screw-CARR35139-25971Screw-HHF73441-881ACaster,Wheel and Tire Assembly3441-881A8D0Caster,Wheel and Tire Assembly(continued)Ref.Part Number Qty.Description 1138-9839-012Fork ASM 2139-58432Tire ASM2:1140-03741Tire2:3232-271Stem-Valve2:4114-16402Bushing-Flange 2:5302-51Fitting-GreaseRef.Part Number Qty.Description5138-98032Spacer-Spanner6325-362Screw-HH799-51072Nut-Lock83256-682Washer-Flat93234-472Screw-HHF93441-881ATraction Drive Assembly3441-881A10E0Traction Drive Assembly(continued)Ref.Part Number Qty.Description1139-74701LH Hydro Transaxle ASM 2139-74711RH Hydro Transaxle ASM 3138-2571-031Crossplate-Hydro4139-23991V-Belt5138-98091Spacer6138-72761Arm-Idler7138-72771Spacer-Arm,Idler868-00301Idler9138-75971Pulley-Idler,Flat10137-70401Spring-Return,Pedal 11138-72451Rod-Bypass,RH12138-72431Rod-Bypass,LH133290-3072Pin-CotterRef.Part Number Qty.Description143230-81Screw-CARR15115-17941Screw-HHF16138-75904Screw-HHF17322-114Screw-HH18324-82Screw-HH19324-104Screw-HH215-44601Washer-Pivot22104-830010Nut-HF,NI243296-486Nut-Hex25242-508Nut-Lug323256-256Washer-Flat333256-232Washer-Plain34119-89522Washer113441-881ALH Transaxle Assembly No.139-74703441-881A121LH Transaxle Assembly No.139-7470(continued)Ref.Part Number Qty.Description1106-86951Main Housing ASM 2106-86961Side ASM4110-85611Pump Block ASM6103-26661Cylinder Block Kit7104-21891Plug-Thread,Straight 9117-535916Screw-HHF14106-86772Ring-Retaining,External 15106-86781Rod-Bypass16106-86791Ring-Retaining,Internal 19104-53041Swashplate-Trunnion 21104-21161Stud22112-98531Puck-Friction2794-19361Spring-Block2894-19371Washer-Thrust29104-53061Shaft-Input30104-53111Bearing-Ball31104-53071Ring-Retaining32104-53081Spacer33104-53101Seal-Lip34104-53092Ring-Retaining3594-69222Bearing-Thrust36104-53391Washer-Flat37104-53401Ring-Retaining38132-09121Gear-12T39106-86831Shaft-Motor40104-53601Washer4194-19332Washer42132-09111Gear-49TRef.Part Number Qty.Description43104-53181Gear-Jackshaft,10T44104-53291Pin-Jackshaft45112-98541Ring-Spiral,Retaining46112-98551Gear-52T,Bull47112-98561Washer48112-98571Bearing-Sleeve49120-71041Shaft-Axle50112-98591Bushing-Axle51112-98601Seal-Lip52106-86861Seal Kit53106-86971Expansion Plate Kit54135-73491Fan And Pulley Kit54:1116-97141Nut-HJ54:2116-97081Washer-Slotted54:4135-73641Fan7.0X10Blade55106-86881Brake Arm Kit57112-98611Center Section Filter Kit58104-21471Sealant59120-55491Bypass Kit61114-16341Filter Kit98120-71091Tube-Axle100106-86941Disc-Brake,Cog101115-50571Cover-Nut,Axle124109-59391Hub Kit138112-98661Breather Kit139114-16351Breather ASM200117-53621Control Arm Kit209114-84671Puller-Hub,4Bolt133441-881ARH Transaxle Assembly No.139-74713441-881A142RH Transaxle Assembly No.139-7471(continued)Ref.Part Number Qty.Description1106-86741Main Housing ASM 2106-86751Side ASM4110-85611Pump Block ASM6103-26661Cylinder Block Kit7104-21891Plug-Thread,Straight 9117-535916Screw-HHF14106-86772Ring-Retaining,External 15106-86781Rod-Bypass16106-86791Ring-Retaining,Internal 19104-53041Swashplate-Trunnion 21104-21161Stud22112-98531Puck-Friction2794-19361Spring-Block2894-19371Washer-Thrust29104-53061Shaft-Input30104-53111Bearing-Ball31104-53071Ring-Retaining32104-53081Spacer33104-53101Seal-Lip34104-53092Ring-Retaining3594-69222Bearing-Thrust36104-53391Washer-Flat37104-53401Ring-Retaining38132-09121Gear-12T39106-86831Shaft-Motor40104-53601Washer4194-19332Washer42132-09111Gear-49TRef.Part Number Qty.Description43104-53181Gear-Jackshaft,10T44104-53291Pin-Jackshaft45112-98541Ring-Spiral,Retaining46112-98551Gear-52T,Bull47112-98561Washer48112-98571Bearing-Sleeve49120-71041Shaft-Axle50112-98591Bushing-Axle51112-98601Seal-Lip52106-86861Seal Kit53106-86871Expansion Plate Kit54135-73491Fan And Pulley Kit54:1116-97141Nut-HJ54:2116-97081Washer-Slotted54:4135-73641Fan7.0X10Blade55106-86881Brake Arm Kit57112-98621Center Section Filter Kit58104-21471Sealant59107-24891Bypass Arm Kit61114-16341Filter Kit98120-71091Tube-Axle100106-86941Disc-Brake,Cog101115-50571Cover-Nut,Axle124109-59391Hub Kit138112-98661Breather Kit139114-16351Breather ASM200117-53621Control Arm Kit209114-84671Puller-Hub,4Bolt153441-881ABrake Assembly3441-881A16F0Brake Assembly(continued)Ref.Part Number Qty.Description1138-25141Brake Box ASM 2133-9284-031Bracket-Mount,Brake 3138-25911Rod-Brake,LH4138-25921Rod-Brake,RH5117-11694Spring-CompressionRef.Part Number Qty.Description73290-3072Pin-Cotter832144-364Screw-PPH932144-42Screw-HWH10119-89526Washer113296-422Nut-Lock,NI173441-881ARear Tire Assembly3441-881A18G0Rear Tire Assembly(continued)Ref.Part Number Qty.Description 1139-58492Tire ASM 1:1133-92931Tire Ref.Part Number Qty.Description 1:3232-271Stem-Valve 1:99105-40701Tube-Inner●●Not illustrated193441-881AMotion Control Assembly3441-881A20I0Motion Control Assembly(continued)Ref.Part Number Qty.Description1138-7598-031Plate-Control Box,LH 2138-7599-031Plate-Control Box,RH 4119-34702Actuator Arm ASM4:2256-1562Bushing-Flange5133-9299-052Arm-Control6139-58032Eccentric7138-75392Spring-Torsion8133-70551Handle-Control,LH8:1121-07261Grip9133-70571Handle-Control,RH 9:1121-07261Grip10138-25802Rod-Hydro,Front 11144-18182Rod-Hydro,Rear 12121-17532Pin-Rod,Hydro13138-97501Speed Control ASM 14138-75412Plate-Retainer15132-93681Knob-RH16132-93691Knob-LH17132-68532Damper-Non Cavitating 18138-72152Stud-Damper1993-60792Spacer-NylonRef.Part Number Qty.Description20120-22732Washer-Nylon21119-89252Washer-Belleville22119-89522Washer23139-58112Bolt-Pivot,Eccentric24117-11982Bolt-Pivot25120-79502Screw-Torx26138-72182Mount-Rod,Hydro27115-50992Bolt-Pivot2894-44961Screw-PPH2932144-12Screw-Taptite303229-114Screw-CARR31138-975310Screw323234-424Screw-HHF33104-72014Nut-HF343296-426Nut-Lock,NI35117-12402Washer36119-40414Nut-HF37104-83014Nut-HF,NI39138-72522Spring-Compression40120-96832Washer-Plain213441-881AEngine and Muffler Assembly3441-881A22J0Engine and Muffler Assembly(continued)Ref.Part Number Qty.Description 1139-06031Engine-2P77F 2139-58651Muffler 532144-1094Screw-Thd 63256-243Washer-FlatRef.Part Number Qty.Description9121-01994Nut-HH10127-92794Washer-Lock,Split12120-43172Gasket-Exhaust233441-881AFuel System Assembly3441-881A2402Fuel System Assembly(continued)Ref.Part Number Qty.Description 1139-07171Filter-Fuel2139-07196Clamp-Fuel Hose 3120-43711Line-Fuel4139-06841Pump-Fuel5120-42252Screw-HHF 6127-92051Hose-Fuel7127-92071Hose-Fuel8127-92302Gasket-Intake 9120-42844Screw-HHF 10127-92441Manifold-Intake Ref.Part Number Qty.Description11127-92454Stud12127-92462Gasket-Carburetor13127-92471Insulator-Carburetor14133-99631Linkage-Throttle15133-99641Spring-Return,Throttle 16127-93551Sleeve-Fuel Line Protector 96136-78401Carburetor Replacement Kit 97127-92901Carburetor Repair Kit 98127-92921Solenoid Kit99136-78371High Altitude Kit●●Not illustrated253441-881ACarburetor Assembly3441-881A2602A1Carburetor Assembly(continued)Ref.Part Number Qty.Description1127-92511Gasket-Carburetor 3127-92462Gasket-Carburetor 14127-93191Spring20127-93251Cover-Shaft,Choke 23127-93281Spring25127-93301Spring28127-93331Clamp-Lock29127-93341Screw-PPH30127-93351SpringRef.Part Number Qty.Description90127-92901Carburetor Repair Kit91127-92921Solenoid Kit92127-93401Float Kit93127-93411Bowl Kit94133-98171Throttle Shaft Kit95136-78441Nozzle And Jet Kit96136-78991Idle Jet Kit97127-93451Choke Shaft Kit273441-881AAir Intake and Filtration Assembly3441-881A2803Air Intake and Filtration Assembly(continued)Ref.Part Number Qty.Description 1127-92351Tube-Breather 2127-92342Clamp-Hose 3136-78061Air Filter Kit 3:1136-78041Prefilter4127-92531Hose-FuelRef.Part Number Qty.Description5127-91871Clamp-Hose6120-42364Nut-Flange7127-90471Manifold-Filter,Air8127-92511Gasket-Carburetor293441-881AIgnition and Cooling Fan Assembly3441-881A3004Ignition and Cooling Fan Assembly(continued)Ref.Part Number Qty.Description 1127-91974Screw-HWH 2127-91981Screen-Rotating 3127-91994Screw-HWH 4127-92001Fan-Cooling 5127-92011Screw-HWH 6127-92021Washer-Spring 7127-93061Flywheel8127-92104Screw-HSH 9136-78761Alternator 10136-78801Motor-Starter 11127-92081Bracket-LiftRef.Part Number Qty.Description12120-42312Screw-HHF13121-00074Bolt-Flange14139-07202Ignition Coil ASM16127-92204Tie-Zip17136-78791Regulator-Voltage,W/Harness18120-42161Screw-HHF19120-42322Screw-HHF20133-15621Pinion-Starter98133-15661Starter Repair Kit313441-881ACrankcase and Crankshaft Assembly3441-881A3205Crankcase and Crankshaft Assembly(continued)Ref.Part Number Qty.Description 1120-423214Screw-HHF2127-92121Baffle3127-92131Cover-Breather 4127-92141Gasket-Breather 5127-92151Filter-Breather 6120-42161Screw-HHF7127-92171Valve-Breather 8120-42671Seal-Oil10136-78841Adaptor-Filter,Oil 11136-78481Filter-Oil12127-92181Oil Tube ASM 12:1127-92831Dipstick12:2127-92841O-Ring12:4127-92861O-Ring13127-92551Crankshaft13:1120-43201Key-Woodruff 14127-92611Cover-Screen,Oil 15127-92621Screen-Oil 16127-92631Retainer-Screen 17120-42742Pin-Dowel18127-92641Plate-Retainer 19127-92651SpringRef.Part Number Qty.Description20127-92661Valve-Ball21120-42622O-Ring22127-92671Gasket-Cover,Crankcase23133-98051Plug-Drain24133-98061Cover-Crankcase25127-92931Oil Drain Hose ASM26127-92751Fitting-Hose27127-92761Clamp-Hose28127-92711Seal29121-047310Screw-HHF30127-92741Cover-Oil Pump31127-92731O-Ring32127-92721Oil Pump ASM33120-42751Deflector-Oil,Rubber34133-15681Camshaft35136-78821Governor ASM36127-92381Shaft-Governor37120-42582Washer-Plain38120-42571Seal-Oil39120-42561Pin-Hair40120-42322Screw-HHF333441-881AGovernor Control Assembly3441-881A3406Governor Control Assembly(continued)Ref.Part Number Qty.Description1127-92502Clip-Linkage2127-92421Linkage-Choke 3127-92411Spring-Governor 4120-42381Bolt-Arm,Governor 5120-42361Nut-FlangeRef.Part Number Qty.Description6133-99611Arm-Governor7133-99621Spring-Governor8133-15701Control Plate ASM9120-42322Screw-HHF353441-881APiston and Cylinder Head Assembly3441-881A3607Piston and Cylinder Head Assembly(continued)Ref.Part Number Qty.Description1127-92562Connecting Rod ASM 2127-92584Clip-Pin,Piston3127-92572Pin-Piston4127-92592Piston5127-92602Piston Ring Set6127-92244Lifter-Valve7127-92254Rod-Push8127-92262Gasket-Head,Cylinder 9127-92274Pin-Dowel10127-92282Valve Set11133-98021Head-Cylinder,Right 12133-98041Head-Cylinder,Left 13121-04644Stud-Exhaust14120-43172Gasket-Exhaust 15127-92794Washer-Lock,Split 16121-01994Nut-HHRef.Part Number Qty.Description1781-32502Spark Plug18127-92316Screw-HWH19127-92324Screw-HWH20120-43034Seat-Spring,Valve21120-43044Seal-Stem,Valve22120-43054Spring-Valve23120-43064Retainer-Spring,Valve24120-43078Keeper-Valve25127-92332Plate-Guide,Push Rod26136-78814Rocker Arm ASM27127-92952Gasket-Valve Cover28127-90502Cover-Valve29120-42258Screw-HHF30120-42141Screw-Shoulder,HH31136-78911Complete Right Head ASM32136-78921Complete Left Head ASM 373441-881ABlower Housing Assembly3441-881A3808Blower Housing Assembly(continued)Ref.Part Number Qty.Description1133-15714Screw-PPH,Plastic 2127-90451Cover-Fan3127-91966Screw-Shoulder,HWH 4133-15721Shroud-Engine5127-90461Door-Filter,Air6127-92802Pin-Hair7127-92822PinRef.Part Number Qty.Description8127-92811Plate-Spring9136-78771Baffle-Air,Left10120-42102Screw-Shoulder,HHF11136-78781Baffle-Air,Right12127-92871Cleat-Hose13120-42322Screw-HHF393441-881AGasket and Seal Kit3441-881A4009Gasket and Seal Kit(continued)Ref.Part Number Qty.Description1127-92961Gasket And Seal Kit 1:1127-92141Gasket-Breather1:2120-42671Seal-Oil1:3127-92262Gasket-Head,Cylinder 1:4127-92302Gasket-Intake1:5127-92952Gasket-Valve Cover 1:6120-43172Gasket-Exhaust1:7120-42571Seal-Oil Ref.Part Number Qty.Description1:8127-92462Gasket-Carburetor1:9127-92511Gasket-Carburetor1:10120-42622O-Ring1:11127-92671Gasket-Cover,Crankcase 1:12127-92711Seal1:13127-92731O-Ring1:14127-92841O-Ring1:15127-92861O-RingFuel Pod AssemblyFuel Pod Assembly(continued)Ref.Part Number Qty.Description1138-9810-031Bracket-Pod2138-6071-031Support-Pod,LH3139-3271-031Support-Tank,Fuel4138-60741Pod-LH5139-24041Pod-RH,Myride6138-60721Fuel Tank ASM6:1139-10911Connector-Elbow,90DEG 6:2117-74001Fitting-Plastic6:346-65602Bushing76098302Spring8137-41191Cap-Fuel,Ratcheting 91070691Clip10139-2380-031Panel-Control Ref.Part Number Qty.Description11139-23911Decal-Panel,Control 14139-24031Cable-Throttle 15139-24021Cable-Choke18108-45821Hose-Fuel19109-02941Hose-Fuel23117-53991Adaptor-Orifice 242412-983Clamp-Hose 256142491Tie-Cable263258-1661Screw-PRH27120-79506Screw-Torx28138-97535Screw31120-78931Bumper-GrommetElectrical AssemblyElectrical Assembly(continued)Ref.Part Number Qty.Description1138-25211Harness-Wire1:11093551Fuse-Blade,15Amp 1:21091021Fuse-Blade,25Amp 2105-16921Battery,230CCA W/OElectrolyte3117-11971Solenoid4137-41001Switch-Ignition563-83601Key-Ignition6103-52211Switch-PTO7110-67652Switch8139-23811Strap-Rubber9140-27131Cable-Battery,Pos 10139-24311Cable-Battery,Red(8Gauge)Ref.Part Number Qty.Description11110-67931Cable-Battery,Black 133256-222Washer-Flat 1432144-42Screw-HWH15321-31Screw-HH163234-141Screw-HHF 173229-11Screw-CARR 1832128-331Nut-HF1932103-221Nut-Wing203220-22Nut-Jam2133003-001Nut-HF22140-20801Cover-Solenoid 23140-20811Cap-Solenoid 2432180-4181Clip-Harness54in Deck and Decal Assembly54in Deck and Decal Assembly(continued)Ref.Part Number Qty.Description1138-9766154In Deck And Decal ASM 1:393-70091Decal-Danger1:4132-08722Decal-Danger,Deck1:599-39431Decal-Routing,Belt1:7112-98401Decal-Scalp,Anti6140-21241Decal-Deck7139-2448-031Baffle-Corner8138-97532Screw9139-32143Spindle ASM9:2120-79352Spacer9:3138-97702Bearing-Ball1032144-4112Screw-Taptite11117-72683Shaft-Spindle12138-72613Pulley ASM133219-63Nut-Hex14115-2454-033Blade-Hi Lift153290-4653Washer-Belleville1626-06713Screw-HH17132-94203Pulley-Idler,Flat183256-242Washer-Flat19323-93Screw-HH20110-99811Washer-Plain2163-74002Washer-Rebound22114-04632Washer-Friction,Composite 23115-49861Spacer Ref.Part Number Qty.Description24104-83017Nut-HF,NI25138-72621Arm-Idler26130-08431Belt-V27137-20191Rod-Pivot28138-75021Deflector-Discharge 29138-72681Spring-Torsion 30138-9800-031Baffle-Cutoff 313296-591Nut-Lock,NI321-6032993Roller-Scalp,Anti 33112-39773Bolt-Shoulder 34133-92892Fitting-Washout 34:2133-92901O-Ring3532144-44Screw-HWH36138-72661Spring-Return,Hook 37138-72641Spring-Extension 38139-58712Pin-Deck39144-19062Cover-Belt4095-32701Connector-Hose 41139-3272-032Bracket-Cover,Belt 42138-72071Spacer-Hub,Blower 43138-72701Guide-Belt,Idler 45323-111Screw-HH46144-19442Pin-Hair4794-69612ScrewFrame Decal AssemblyFrame Decal Assembly(continued)Ref.Part Number Qty.Description 3140-51321Decal-Engine 4131-10971Decal-Drain,Oil 5131-41571Decal Ref.Part Number Qty.Description 6127-90761Placard-Intake 7132-09041Decal-Shutdown 10140-20991DecalSeat Pan Assembly。

FOREFLIGHT BUYING GUIDE/buying-guideProducts, Plans, & PricingFOREFLIGHT BUYING GUIDEGETTING STARTED WITH FOREFLIGHTGet up and running with the leading EFB with these simple steps!Enhance your postflight debrief and refine your flying skills with CloudAhoy Debrief, a data-driven flight analysis tool that integrates directly with ForeFlight Mobile. Sign up for a risk-free 35-day free trial, download the CloudAhoy app, and upload your recorded Track Logs from ForeFlight to experience the value of objective postflight analyis.Try CloudAhoy DebriefDownload the Pilot’s Guide to ForeFlight Mobile in the Documents tab for the authoritative resource on all features, visit ForeFlight’s online Video Library to watch tutorials, recorded webinars, and scenario-based presentations, and go to More > Support in the app to access these and other valuable support resources at any time.Still stuck? Our expert Pilot Support Team is ready to answer any question you have at *******************.Training & SupportInstall ForeFlight Mobile EFB from the App Store on your chosen device and create an account to start your 30-day free trial. During the trial you’ll have access to all the features available with our top subscription plan - Performance Plus - so you can see everything the app has to offer before purchasing.Start Your Free TrialForeFlight works with all recent iPad and iPhone models, and you can sign into your subscription on up to 2 iPads and 1 iPhone, or 2 iPhones and 1 iPad at once. If buying a new iPad, we recommend the Wi-Fi + Cellular version of either the 11-inch iPad Pro or the iPad mini to benefit from the built-in GPS chip.Choose a DeviceSIGN UP FOR A FREECLOUDAHOY TRIALVISIT OURSUPPORT CENTERDOWNLOAD FROMTHE APPLE APP STOREFULL DEVICE RECOMMENDATIONBasic PlusFor basic flight planning, flying, and logging.BEST FOR: FLAT, RURAL, & FAIR-WEATHER FLIGHTS • PPL STUDENTS • INFREQUENT FLYERS Basic Flight Planning & FilingPlan a route in seconds with intuitive touch-planning andsmart altitude selection, check your time and fuel burnestimates based on aircraft performance, and file VFR orIFR flight plans with ease. Easily access global airport,FBO, and aeronautical information like frequencies,runways, NOTAMs, and more.Live & Forecast WeatherMap-based weather layers provide animated radarand satellite, METAR-derived current conditions, AIR/SIGMETs, and more, plus decoded TAF, MOS, and windsaloft forecasts for airports. Plan hours or days ahead withstatic weather imagery from NOAA and NWS, as well as a10-day hourly general forecast with an aviation twist.Charts & DocumentsPlan and fly with government-sourced VFR and IFRcharts, procedure plates, and airport diagrams for yourregion, plus an extensive Documents catalog witheverything from regulatory texts and advisory circulars tochart supplements and legends, airport directories, andeducational handbooks.Moving Map & Inflight FeaturesSeamlessly transition from planning to flying with a rangeof map overlays and inflight tools to assist with navigationand awareness. Fly safely with a multitude of visual andaudio alerts and live display of ADS-B traffic and weather*from supported devices.Postflight Logging & DebriefingRecord your flights with Track Logs and debrief themdirectly in ForeFlight or send them to CloudAhoy fordetailed postflight analysis. ForeFlight’s digital logbookmakes it easy to share flights with fellow pilots or yourinstructor for their signature, track hours and currency,record new certificates and ratings, and much more.*In supported regions.Pro PlusAdds safety-enhancing terrain and situational awareness features and helpful tools for IFR flying.BEST FOR: XC, MOUNTAINOUS, URBAN FLIGHTS •HAZARD AWARENESS •IFR STUDENTSIncludes everything in Basic Plus, and...Synthetic Vision (top), Hazard Advisor shading and Glide Advisor with approach plate on map (bottom)Inflight Hazard AwarenessAdvanced Route &Weather VisualizationMust-Haves for IFR FlyingVisualize terrain and fly more confidently witha trio of feaures that highlight hazards from multiple perspectives.Plan more easily around (or above) complex airspace and TFRs with Profile View’s interactive route display and multi-altitude planning. Bolster your weather planning with global forecast layers for Icing, Turbulence, Cloud Coverage, and Surface Analysis.Give yourself a break in the soup with powerful features to enhance your IFR flying workflow. View your position directly on geo-referenced procedure plates and taxi charts and overlay them on the map for a fully integrated view. Easily insert holding patterns anywhere in your route with automatic pattern entry selection.Profile View & CorridorHazard AdvisorSynthetic VisionEasily locate hazards near your route with both an interactive side-on view and its associated corridor on the map revealing the highest peaks and obstacles along each leg.Highlights hazardous terrain and obstacles directly on the overhead map, with an adjustable altitude slider to quickly plot a safe route through heavy terrain.An interactive 3D display of terrain, obstacles, runways, and nearby ADS-B traffic targets. Provides an emergency backup attitude capability when paired with an AHRS device like Sentry.Performance PlusBest-of-the-best in preflight weather, airport familiarization, and optimized performance planning.BEST FOR: EXPLORING NEW SKIES • MAXIMIZING PERFORMANCE •FREQUENT IFR FLYERSAdvanced Weather VisualizationOptimized Flight Planning3D Airport & Route VisualizationTurbine Aircraft EssentialsAugmented IFR ProceduresPlan with Icing, Turbulence, and Cloud Coverage forecasts integrated into Profile and 3D View to easily find the best altitude for a smooth ride. Dynamic Wind Speed and Temperature forecast layers offer weather insights from the global to the local.Speed up and simplify your flight planning with integrated Weight & Balance calculations anddetailed fuel planning. Takeoff & Landing Distances for piston aircraft help you ensure a safe flight no matter the airport, and ForeFlight’s optimized Recommended Route gets you “cleared as filed” nearly every time.Familiarize yourself with new airports and routes to identify landmarks, preview your approach, check the active runway with live traffic, and see where weather may impact your flight. Replay any recorded flight in 3D to debrief maneuvers or relive your favorite moments.The ultimate app for jet and turboprop pilots, with stunningly accurate performance calculations based on OEM data, contract Jet-A fuel cardmanagement, FMS flight plan uplink, pre-departure clearance and digital ATIS, and support forForeFlight’s integrated Runway Analysis product.View critical approach fix information as part of your route to maximize visibility and reduce the risk of errors. ForeFlight helps you find the appropriate minimum for your aircraft and highlights it on the map, as well as displaying speed and altitude restrictions for every fix.Includes everything in Pro Plus, and...3D Route Preview with Augmented Approach Fixes and Minimum AltitudeCANADA & ALASKAEUROPE IFR & VFREURASIALATIN & SOUTH AMERICANORTH AMERICAAFRICAAUSTRALIA & NEW ZEALANDMIDDLE EASTPACIFICUSA+WORLDWIDE JEPPESEN IFR CHARTSEnhance your IFR flying with industry-standard Jeppesen charts, available as optional add-ons to any individual ForeFlight Mobile subscription. Coverages include departure, arrival, terminal procedures, data-driven enroute charts, airport charts, and Jeppesen Airway Manuals.Ways to Add Jeppesen Charts in ForeFlightPurchase Coverages from ForeFlightLink Active Jeppesen AccountDownload & View Jeppesen Charts in ForeFlight MobileNew and existing ForeFlight Business customers can contact ForeFlight’s Sales team at ******************** to purchase chart coverages with their ForeFlight subscription. Individual customers can select and purchase chart coverages directly via /buy .In addition to buying directly through ForeFlight, you can also log into your Jeppesen account in More > Jeppesen using your Jeppesen username and password to activate and download existing chart coverages.Chart coverages are automatically queued for download after purchasing or activating them. Access Jeppesen charts throughout ForeFlight Mobile in the same familiar way you access government charts - Jeppesen charts are always listed first when available.View coverage pricing at /buy.EUROPEAN VFR CHARTSAll European ForeFlight subscriptions include Jeppesen’s VFR navigation data for Europe and global IFR navigation data, as well as Jeppesen's high-quality global terrain, obstacle, and airspace datasets.Enhance your VFR flying in Europe with charts, AIPs, and documents from Jeppesen and other popular chartmakers. Available as add-ons to any ForeFlight subscription that includes the Europe region . Visit /europe-data for coverage maps and pricing.Included Jeppesen DataJeppesen VFR Navigation Data CoverageIntegrated seamlessly into ForeFlight's Aeronautical Map, Jeppesen's digital VFR navigation data dynamicallyappears as you pan and zoom. Includes VFR waypoints, entries and exits, traffic circuits, no-overfly areas, and more.JEPPESEN VFR PROCEDURE CHARTS *Full coverage beside easternmost EuropeROGERS DATA *†VFR 500K Charts for all except easternmost EuropeIGN French VFR ICAO ChartsANS Finnish VFR ICAO ChartsSKYGUIDE VFR GUIDESwiss VFR Flight GuideNATS U.K. VFR ICAO ChartsAVINOR Norwegian VFR ICAO ChartsLFV Swedish VFR ICAO ChartsCARTABOSSY VFR 1:1M Chart for France, Switzerland,& BelgiumDFS *†VFR 500K Charts for Western, Central, & Southern EuropeAIR MILLION VFR 1:1M Charts for Western, Central, & Southeast EuropeAVIOPORTOLANO Italian VFR ICAO Charts & Flight Guide* Available for individual countries / regions or as a bundle†AIPs / flight guides / trip kits and procedure charts available for certain countriesFOREFLIGHT RUNWAY ANALYSISCLOUDAHOY DEBRIEFEssential Safety Made EasyData-Driven Postflight AnalysisSafety meets convenience with a sophisticated runway and obstacle analysis for turbineaircraft that’s fully integrated with ForeFlight’s planning workflow.Enhance your postflight debrief and refine your flying skills with CloudAhoy Debrief, a data-driven flight analysis tool that integrates directly with ForeFlight Mobile.Available for purchase by aircraft type with Performance Plus and Business Performance subscription plans. Visit /runway to learn more and see the full list of supported models.Visit /signup to get started with a 35-day free trial.Automatic calculations with every change Integrated with Weight & BalanceVisualize EOPs in 3D or on the mapTakeoff trim calculations supported for most aircraft Over 10,000 RNAV Engine-Out Procedures globally Automatic flight analyzer identifies legs, maneuvers, and procedures for focused reviewCompare all recorded parameters with flight graphs Share your flights with friends & family directly or via social mediaView flight track in 2D & 3D with charts & map overlays Receive scores on individual segments & procedures to identify opportunities for practiceSENTRY ADS-B RECEIVERSA variety of installed avionics connect with ForeFlight Mobile to deliver capabilities like two-way flight plan transfer, ADS-B weather and traffic, AHRS for backup attitude, GPS position, and more.* Weather and traffic display supported on Experimental systems running software version 15.4.7 and higher. ** For Light Sport and Experimental aircraft. † Portable DeviceInstalled Avionics SystemsADS-B Weather & TrafficGPSBackup Attitude (AHRS)ConnectionPressure AltitudeFlight Plan TransferDYNON Skyview*Wi-FiFREEFLIGHT RANGRWi-FiUAVIONIXAIR AVIONICSL3HARRISLynxWi-FiONBOARD WI-FI SYSTEMS - REQUIRES PERFORMANCE PLANS Stratus 2 / 2S / 3Stratus 1S / 2 /2S / 3APPAREO ESG / ESGiWi-Fi ADL 180† / 190 / 200ADL Connect for IridiumGO!†GOLZE ENGINEERING ADL 140†/ 150BWi-Fi Wi-Fi Wi-FiSatellite Wx Satellite WxTraffic & Sat. Wx HONEYWELLAVIDYNEIFD 440 / 540 / 550Wi-FiIFD 550INSTALLED AVIONICS SYSTEMSForeFlight integrates with Garmin’s Connext ecosystem via the Flight Stream 110, 220, and 510 Bluetooth wireless gateways, as well as several all-in-one panel devices.Garmin Installed AvionicsADS-B Weather & TrafficGPSBackup Attitude (AHRS)ConnectionPressure AltitudeFlight PlanTransferFLIGHT STREAMALL-IN-ONEPlease note this table highlights common avionics configurations and may not be an exhaustive list of every equipment combination.GARMIN INSTALLED AVIONICS/buying-guideSubscriptions include 1 region; additional regions $100 USD each.Select Your Region(s)Select Add-onsUSCanadaFAA VFR & IFR Charts • Procedure Plates •Taxi Charts • DocumentsEuropeJeppesen VFR Navdata • National VFR & IFR Charts, Procedures, & Documents via EUROCONTROLAustraliaAirservices VFR & IFREnroute Charts • Procedure & Aerodrome Charts • DocumentsNAV CANADA VNC & IFR Charts • Procedure Plates Taxi Charts • DocumentsJeppesen ChartsGlobal IFR Enroute Charts • Procedure Plates • Taxi Charts • Airway ManualsRunway AnalysisIntegrated Runway &Obstacle Analysis product for jets and turboprops. Requires Performance subscription.Europe OnlyFLARM LicenseVFR ChartsDisplay FLARM traffic in ForeFlight Mobile from a Sentry Plus or SkyEcho 2 portable receiver.VFR Procedure Charts • VFR ICAO charts • Procedure Charts, AIPs, & Documents0723v6。