地毯使用说明书

Carpet Spotter Revised 8/03OPERATION SERVICE PARTS CARE Model: C46200-00C46200-02C46200-02CEFOR COMMERCIAL USE ONLYIMPORTANT SAFETY INSTRUCTIONSWhen using an electrical appliance, basic precautions should always be followed, including the following:READ ALL INSTRUCTIONS BEFORE USINGWARNING - To reduce the risk of fire, electric shock, or injury:•Do not leave appliance when plugged in. Unplug from outlet when not in use andbefore servicing.WARNINGTo reduce the risk of electrical shock, do not expose to rain. Store indoors.•Use motorized tool on carpet moistened by the cleaning process.•Do not allow to be used as a toy. Close attention is necessary when used by or nearchildren.•Use only as described in this manual. Use only manufacturer’s recommendedattachments.•Do not use with damaged cord or plug. If appliance is not working as it should, hasbeen dropped, damaged, left outdoors, or dropped into water, return it to a servicecenter.•Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cordaround sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.•Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.•Do not handle plug or appliance with wet hands.•Do not put any object into openings. Do not use with any opening blocked; keep freeof dust, lint, hair, and anything that may reduce air flow.•Keep hair, loose clothing, fingers, and all parts of body away from openings andmoving parts.•Do not pick up anything that is burning or smoking, such as cigarettes, matches, orhot ashes.•Do not use without dust-bag and/or filters in place.•Turn off all controls before unplugging.•Use extra care when cleaning on stairs.•Do not use to pick up flammable or combustible liquids such as gasoline or use inareas where they may be present.•Connect to a properly grounded outlet only. See grounding instructions.SAVE THESE INSTRUCTIONSINSPECTIONCarefully unpack and inspect your machine for shipping damage. Each unit is tested and thoroughly inspected before shipment, and any damage is the responsibility of the delivery carrier who should be notified immediately.ELECTRICAL - Model C46200-00 (115V)This machine is designed to operate on a standard 15 amp. 115 volt, 60 hz, AC circuit. Voltages below 105 volts AC or above 125 volts AC could cause serious damage to the motor. ELECTRICAL - Model C46200-02, C46200-02CE (230V)This machine is designed to operate on a standard 16 amp. type L fused 230 volt, 50 hz, AC circuit. Voltages below 200 volts AC or above 250 volts AC could cause serious damage to the motor. I.E.C. Class 1.WARNINGElectric motors can cause explosions when operated near explosive materials or vapors. Do not operate this machine near flammable materials such as solvents, thinners, fuels, grain dust, etc.GROUNDING INSTRUCTIONSThis appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.DANGER - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance -- if it will not fit the outlet, have a proper outlet installed by a qualified electrician.This appliance is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in sketch A below. Make sure that the appliance is connected to an outlet having the same configuration as the plug. No adapter should be used with this appliance.USER MAINTENANCE INSTRUCTIONSAll service and repair should be performed by qualified vacuum service representative or electrician. No user serviceable components are employed in the electrical vacuum lid head assembly. No lubrication of the motor is required.DAILY MAINTENANCE1.Solution tank should be emptied after each use. Flush pumping system with 1 gallon ofclean water after use.2.Check and clean vacuum inlet and solution inlet strainer daily.3.Removable recovery tank, page 7, item 30, should be rinsed clean daily.4.Spray jet should be checked for correct spray pattern and cleaned if plugged. Do not cleanout spray tip with pins or wire, this may cause damage to the jet spray pattern and cause streaking.5.Protect equipment from freezing. Severe pumping system damage can occur if allowed tofreeze.6.Inspect vacuum hoses for tight connections. Check electrical cable for abrasion or cuts injacket. Cord should be replaced if worn or damaged.MONTHLY/BI-MONTHLY MAINTENANCEThe Solution Pump System should be purged monthly to remove alkaline residue build-up. To flush system out, use 1 quart of white vinegar to 1 1/2 gallons of clean hot water, followed by a clear 1 1/2 gallon rinse. Clean spray jets if required.CORD STORAGEWhile not in use storage can be accomplished by winding cord around top of machine. Cord hooks are provided.•Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return to service center.•Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.•Do not unplug by pulling cord. To unplug, grasp the plug, not the cord.•Do not handle plug or appliance with wet hands.This equipment should be stored indoors and not exposed to rain.OPERATING INSTRUCTIONS1.Lift the recovery tank of solution tank by releasing the two latches.2.Add up to 1 1/2 gallons of hot water (maximum 140°F) to the solution tank. If chemicals arerequired, follow dilution ratios as specified on product label. Use only commerciallyavailable cleaning chemicals intended for use on carpet.3.Place recovery tank back on solution tank and fasten the two latches.4.Plug power cord into grounded wall outlet.5.Connect the vac/solution hose assembly to machine.6.This machine is equipped with a 3-position power switch. Ref. to figure below. The singlebar position is for vacuum only - center position is off. Double bar position is for vacuum pump and motorized tool (120V and standard 230V). Turn on machine in the single bar position (CE version 230V only).7.Always test upholstery for color fastness in a hidden area before beginning cleaningprocess.8.Warning: This unit does not contain any automatic liquid shut-off devices in the vacuumrecovery tank. Do not overfill. Always completely empty recovery tank before refillingsolution tank. If foam or liquid comes out of ventilation openings turn off immediately.Remove recovery tank and run for 1 minute to flush all liquid from vacuum fan chamber.BEFORE EACH USE OF THE CARPET SPOTTER:Parts Listing - 120V & 240VITEM PART NO QTY DESCRIPTION14502131Frame Weldment (120V)1A4502351Frame Weldment (230V)24502262Wheel 4"37407261Terminal Block 3-Position3A7421011Terminal Block 4-Position 43800641Foam Ring57403871Cord 18-3, 25 FT, Spade Term5A7422481Cord Asm 230V Crptsptr61500041Heyco Strain Relief77114001Nut-Pipe Lock 1/4 NPT87421021Switch 2-Position97622992Rubber Grommet107111042SCR-ST B 10 x .37117404481Ground Fault Interruptor 115V Only 124502521Bottom Gasket137422441Vac Motor Assy. 115V13A7422471Vac Motor Assy. 230V147125602SCR-MC 1/4-20 x .50 SS Nyloc 157115046WSR-Flat 1/4 SS168297571Pump 50 PSI 115V16A7421501Pump 230V, Bypass174500401Elbow PLT 3/8MPT x 3/8Barb 184502281Hose Output 1/4 ID x 15 CL 194520371Crimp Clamp 170R204502271Hose Input 3/8 ID x 12 CL 217102071SCR-MC 6-32 x .87 ST PL 227126388Nut-Hex 10-24 SS Nyloc 237125371SCR-MC 10-24 x .75 SS 247129081Nut-Flanged Wizz 10-24 257129052Nut-Hex 10-24267150291Decal - Serial Number277151791Decal - Spotter Switch 2845022211/4 90° BARB x 3/8 MPT 297113011Nut-Hex 6-32307150091Decal Warning318284901Crimp Clamp 140R327127702WSR-Int. Tooth 10337422401Wire Assy. Violet 16 AWG 120V Only 33A7422501Wire Assy. Violet 16 AWG 230V Only 347422411Wire Assy. Black 16 AWG 357422421Wire Assy. White 16 AWG 120V Only 367422431Wire Assy. White 16 AWG 377400992Wire Tie Small (not shown) 384502511Vac Motor Shroud394502531Front Gasket404502471Top Gasket417125434SCR-MC 10-24 x 3.50 FH SS 427125324SCR-MC 10-24 x 1.00 SS 437410381Receptacle44410-4419AA2Pop Rivet457153401Decal (120V)45A7153411Decal (240V)ITEMPART NO QTY DESCRIPTION 1450213CE 1Frame Weldment 24502262Wheel 4"37407261Terminal Screw Tab 43800641Foam Ring 57423811Cord Set 25 ft. 1.0 m.m.61500041Heyco Stain Relief 77114001Nut-Pipe Lock 1/4 NPT 87421021Switch 2 Position 97622992Rubber Grommet 107422921Ambassador CE RFI Torrid 117111242SCR-ST B 10 x .37 NI 124502521Bottom Gasket 137422471Vac Motor Assembly 230V 147125602SCR-MC 1/4-20 x .50 SS Nyloc 157115046WSR-Flat 1/4 SS 167421501Pump 230V Bypass 174500401Elbow PLTMPT x 3/8 Barb 184502281Hose Output 1/4 ID x 15 CL 194520371Crimp Clamp 170R 204502271Hose Input 3/8 ID x 12 CL 217102071SCR-MC 6-32 x .87 ST PL 227126388Nut-Hex 10-24 SS Nyloc 450220CE 230V European Parts ListingITEM PART NO QTY DESCRIPTION 237125371SCR-MC 10-24 x .75 SS 247129081Nut-Flanged Wizz 10-24257129052Nut-Hex 10-24267150291Decal - Serial Number 277151792Decal - Spotter Switch 2845022211/4 90° BARB x 3/8 MPT 297113011Nut-Hex 6-32307150091Decal Warning 318284901Crimp Clamp 140R 327127701EMI Filter 337422401EMI Filter Mounting Plate 347422412Terminal Insulated 357422424SCR-MC 10-24 x 1.00 SS 367422434SCR-MC 10-24 x 3.50 FH SS 377400992Wire Tie Small (not shown)384502511Vac Motor Shroud 394502531Front Gasket 404502471Top Gasket 417125434Wire Asy Violet 16G 427125324Wire Asy Black 16G 437410381Wire Asy 16G White 448276662Wire Asy 16G WhiteParts ListingITEM PART NO QTY DESCRIPTION177126212Nut-Keps 8-32 SS1871254014SCR-MC 10-24 x 3/8 SS 197127706WSR-Int Tooth 102071002510SCR-MC 8-32 x 3/8 SS 214502072Latch224301032Spring Hook2345022511/4 BARB x 1/8 FPT Brass 247127673WSR-Flat .406 x .75 x .03SS 254502051Quick Disconnect Plate264502211Quick Connect 2202 Coupler 277115526WSR-Int Tooth 8284502091Gasket 294502141Strap304502011Recovery Tank 317151882Decal, Gotcha!ITEM PART NO QTYDESCRIPTION1450202MCH 1Solution Tank Machined 24502291Filter Assembly 34502151Vac Pre-filter 47151801Decal 58323261O-Ring67115943WSR-Flat .56 x .88 x .0378*******/8 Hose BARB x 1/4 FPT 82602941Gasket 98289741Strainer104502161Solution Hose 117153802Decal, Minuteman1282895213/8 BARB x 1/4 MPT PLS 1383390611/4 Street 45 Brass 14000708.03RTV Sealant154520371Crimp Clamp 170R 168284901Crimp Clamp 140RParts ListingITEM PART NO QTY DESCRIPTION14502381Handle Weldment 24502391Frame Weldment 39000402Wheel41300322Hub Cap57115794WSR .56 x 1.0 x .09 67113751Nut 3/8-16 Nyloc77115081WSR .44 x 1.0 x .09 828001613” Caster97125462SCR-MC 10-32 x 1.0 SS 107113502Nut 10-32 Nyloc 119020001Optional - Carpet Spotting KitParts ListingITEM PART NO QTY DESCRIPTION 13900621O-Ring, Valve Seat 23900541Valve Stem, Brass 33900491Spring47123201WSR-Nylon .22 x .45 x .04 53900611O-Ring, Valve Stem 63900601O-Ring, Seal Valve 73900551Cap, Valve83900632Pin97118031Cotter Pin .06 x .75 103900531Trigger117126361Nut, Hex 10-32 SS 123900521Body133900561Mount147125451SCR-MC 10-32 x .87 SS 153900641Coupling164502481Spray Jet173900591Nozzel183900661Solution Valve Assy Comp 194502491Hose Assy Comp4502101Solution Hose, 9.5 Ft4502111Vacuum Hose Assy45021811/4 FPT x 1/8 Barb Brass4502191Q-Connect Male 22-2 SS45022311/8 Barb x 1/8 FPT Brass8280626Cable Tie Large8300822Hose Clamp 3/8LIMITED WARRANTYMinuteman International, Inc. warrants to the original purchaser/user that this product is free from defects in workmanship and materials under normal use and service for a period of one year from date of purchase. In addition, Minuteman International, Inc. will, at its option, honor labor warranty claims for the first 12 months from date of sale, provided such claims are submitted through and approved by factory authorized repair stations. Minuteman International, Inc. will, at its option, repair or replace without charge, except for transportation costs, parts that fail under normal use and service when operated and maintained in accordance with the applicable operation and instruction manuals.This warranty does not apply to normal wear, or to items whose life is dependent on their use and care, such as belts, cords, switches, hoses, rubber parts, electrical motor components or adjustments. Parts not manufactured by Minuteman International, Inc. such as engines, batteries, battery chargers, hydraulic pumps, and tires are covered by and subject to the warranties and/ or guarantees of their manufacturers. Please contact Minuteman International, Inc. for procedures in warranty claims against these manufacturers.Special warning to purchaser — Use of replacement filters and/or prefilters not manufactured by Minuteman International, Inc. or its designated licensees, will void all warranties expressed or implied.A potential health hazard exists without exact original equipment replacement.All warranteed items become the sole property of Minuteman International, Inc. or its original manufacturer, whichever the case may be.Minuteman International, Inc. disclaims any implied warranty, including the warranty of merchantability and the warranty of fitness for a particular purpose. Minuteman International, Inc. assumes no responsibility for any special, incidental or consequential damages.This limited warranty is applicable only in the U.S.A. and Canada, and is extended only to the original user/purchaser of this product. Customers outside the U.S.A. and Canada should contact their local distributor for export warranty policies. Minuteman International, Inc. is not responsible for costs or repairs performed by persons other than those specifically authorized by Minuteman International, Inc. This warranty does not apply to damage from transportation, alterations by unauthorized persons, misuse or abuse of the equipment, use of non-compatible chemicals, or damage to property, or loss of income due to malfunctions of the product.If a difficulty develops with this machine, you should contact the dealer from whom it was purchased.This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions and limitations may not apply to you.World Headquarters Minuteman Canada, Inc.Minuteman International, Inc.2210 Drew Road111 South Rohlwing Road Mississauga, OntarioAddison, Illinois 60101L5S 1B1(630) 627-6900(905) 673-3222988610。

洗地毯机操作方法
洗地毯机的操作方法如下：
1. 准备工具和材料：洗地毯机、洗地毯剂、清洁剂、清洁刷、吸尘器、洁净水。

2. 扫除地面上的垃圾和灰尘，使用吸尘器彻底清洁地毯表面。

3. 将洗地毯剂与洁净水按照产品说明书中的比例混合。

注：如果地毯受到油污或其他顽固污渍，可以先使用清洁剂处理。

4. 将混合好的洗地毯剂倒入洗地毯机的水箱中。

5. 接通电源，启动洗地毯机。

6. 沿着地毯的一侧，均匀地喷洒洗地毯剂。

然后使用洁净刷或推车附件的刷头，从地毯的一侧开始慢慢刷洗地毯。

注意不要过度浸湿地毯，以免造成损坏或变形。

7. 刷洗地毯时，应保持一定的力度和速度，使洗地毯剂和刷子能够充分清洁和抓住污渍。

8. 完成一侧后，继续沿着地毯的另一侧重复以上步骤。

9. 将剩余的洗地毯剂和污水清空，清洁地毯机的水箱和刷子。

10. 使用清水再次彻底地清洗地毯表面，以去除残留的洗地毯剂和污渍。

11. 使用吸尘器彻底地吸干地毯，并确保完全干燥。

12. 最后，对地毯进行观察和检查，确保表面没有残留的污渍和洗地毯剂。

若有需要，可以重复以上步骤直到地毯完全清洁。

注：在操作过程中应注意安全，避免将电线或其他物品纳入地毯机。

同时，根据洗地毯机的具体型号和品牌，还请参考产品使用说明书。

Maintenance manualRoutine/daily maintenance is a combination of vacuum cleaning and spot removal, carried out as often as needed for Effective vacuum cleaning is an essential part of a proper maintenance program to keep soiling to a minimum. Dirt barrier zones and heavy traffic areas, such as lobbies and hallways, should be intensively vacuumed on a daily basis. Other areas, such as offices and board rooms, can be vacuumed daily based on visual inspection witha thorough overall vacuuming at least once a week. For best results Tarkett recommends heavy duty upright Note : For needle punch fiber products like DESSO Lita, high cut pile and polyester yarn made carpets, aswell as woolen loop pile carpets predominantly vacuuming with a suction only vacuum is recommended. Additional to vacuuming, regular spot removal should take place to maintain a good appearance. Ideallyspills are removed immediately to prevent them from becoming permanent stains. The majority of(water based) stains can be removed with a clean white cloth and lukewarm water, after dryingpossibly treated afterwards with an appropriate carpet cleaning agent. Excessive moisture shouldbe absorbed first (from the outside in) and rubbing and excessive use of water should be avoided.Dried or aged stains can first be treated with a blunt object (e.g. a spoon) to remove dried residueby vacuuming. Other (oil based) stains and chewing gum should be treated with a suitable carpetCOMMON STAINSAs stated above, most common (water-based) stains can be removed by using a clean white (cotton) cloth or absorbent paper (without print) and lukewarm water. Other (oil-based) stains should be treated with an appropriate carpet cleaning agent. It is always recommended to remove stains as quickly as possible by following the instructions on the container and by testing it on a concealed part of the floor. In all cases repeat treatments where required after drying until the stains are removed (always avoidingFirst remove any dry compound remaining with a spoon (orequivalent). Use an appropriate carpet cleaning spot removalproduct on a clean white cloth and treat the remaining stain.Note: Never apply a solvent basedstains removal product directly ontothe carpet surface. This can causedissolution of carpet components.Always apply on a white cloth!Similar as coffee/tea/soda/by intensive vacuum cleaning and possibly also spot removal or pre-spraying to loosen stain residues.Hot water extraction is a wet deep cleaning method using a pre-spray and a special machine. Afteragent must be sprayed at the soiled carpet.After that the machine injects clean warm water deep into the carpet to take up the soil and removesthe resulting dirty mix of water and used cleaning agent with a built-in vacuum system and rinse thecarpet surface. This combination is the most effective method. It allows more time for chemical actionand neutralizing the cleaning chemical in the rinse. It is very important not to use excessive amount ofwater to avoid over-wetting the carpet. It is therefore recommended to get a specialist (carpet) cleaningcompany carry out this type of maintenance. Furthermore it is very important to make sure the floor isThe operation of the maintenance program and the use of cleaning agents is a determining factor for the condition of the carpet after its useful life and thus for the options to recycle or reuse the product as part of Tarkett’s Restartprogram. The amount of soil and residue in the carpet determines the quality of the materials fed intoAs part of the implementation process Tarkett is continuously researching into alternative cleaningstrategy and their performance in cleaning andphiliosophy and/or meet the standards of Sebo (e.g.Dart 2), Lindhaus (e.g. RX eco Force and Windsor (e.g. Sensor S2 Hepa) orDue to the ever-changing offerings in spot removers in the efforts of the manufacturersto make an environmental-friendly product, please contact your Tarkett representative.Important for the Routine/Daily maintenance is the presence of a cleaning agent for water-soluble stains coffee, tea, wine etc.) and a remover for oil based stains (grease, paint. etc.) with the needed white (cotton) However, some detergents and cleaning aids should not be used as they do notstandards or have a detrimental effect on the aesthetics*****************。

地毯机的使用流程简介地毯机是一种用于清洁和翻新地毯的机器。

它采用高效的吸尘和清洁技术，可以快速清理地毯上的污渍和灰尘，使地毯恢复清洁、柔软的状态。

本文将介绍地毯机的使用流程。

准备工作在使用地毯机之前，需要进行一些准备工作来确保操作的顺利进行。

1.清理地面:首先，需要清扫地面上的杂物和灰尘。

可以使用一把扫帚或真空吸尘器来完成这个步骤。

2.移动家具:将地面上的家具移动到其他区域，以便可以清理整个地毯表面。

如果家具无法移动，可以使用塑料薄膜或布料来覆盖保护。

3.准备清洁剂:根据地毯的材质选择合适的清洁剂。

确保清洁剂不含有有害物质，并按照说明书的要求进行稀释。

地毯机的使用步骤接下来，我们将一步步介绍地毯机的使用流程。

Step 1: 填充水箱首先，将地毯机的水箱填满清水。

确保使用干净的水来避免在清洁过程中引入更多的污垢。

Step 2: 加入清洁剂根据使用说明，将适量的清洁剂加入到水箱中。

注意使用正确的比例以避免过度使用或过度稀释清洁剂。

Step 3: 调整地毯机设置根据地毯的类型和状态，调整地毯机上的设置。

通常地毯机会有各种各样的设置选项，如清洁模式、水流量和旋转刷等。

Step 4: 开始清洁将地毯机靠近地毯的一侧放下，然后开始慢慢地推动地毯机。

确保将地毯机移动到地板上的每个区域，从而彻底清洁整个地毯。

Step 5: 处理顽固污渍对于顽固的污渍，可以在清洗过程中使用地毯机上的喷射功能或刷头，集中清洁。

需要根据污渍程度和地毯类型进行适当的处理。

Step 6: 清洁角落和边缘使用合适的附件，清洁地毯机无法到达的角落和边缘区域。

这可以确保整个地毯表面都得到彻底清洁。

Step 7: 吸水在完成清洁后，将地毯机切换到吸水模式，将地毯上的多余水分吸干。

确保吸水完成后，地毯表面不再有湿气。

Step 8: 清洁地毯机清洁完成后，需要彻底清洁地毯机本身。

倒掉脏水，并清洗水箱和刷头等部件。

确保地毯机干燥后，存放在干净的地方。

Troubleshooting (7)Guarantee (8)WARNINGTO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:»This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.»Children should be supervised to ensure that they do not play with the appliance.»Unplug from electrical socket when not in use, before cleaning, maintaining,or servicing the appliance, and if your appliance has an accessory tool witha moving brush, before connecting or disconnecting the tool.»Do not immerse in water or liquid.»Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts of the appliance and its accessories.»Use only on carpet or upholstery moistened by the cleaning process.»Liquid must not be directed towards equipment containing electrical components.»Do not immerse. Use only on surfaces moistened by the cleaning process. Use only BISSELL® cleaning products intended for use with this machine.»Use only the type and amount of liquids specified under the operations section ofthis guide.»Always connect to a properly earthed electrical socket. Do not modify earthed plug.»Always install float before any wet pick-up operation.»Plastic film can be dangerous. To avoid danger of suffocation, keep away from children.»Use only as described in this user guide.»Use only manufacturer’s recommended attachments.»If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water; donot attempt to operate it and have it repaired at an authorised service center.»Do not put any object into openings.»Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.»Use extra care when cleaning on stairs.»Do not use to pick up flammable or combustible liquids, such as petroleum, or use in areas where they may be present.»Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).»Do not use appliance in an enclosed space filled with vapours given off by oil-based paint, paint thinner, some moth-proofing substances, flammable dust, or other explosive or toxic vapours.»Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.»Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.»Do not use without filters in place.»Use indoors only.»If the supply cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.»Do not run appliance over cable.»Do not leave appliance when plugged in.»Do not use with damaged cable or plug.»Do not pull or carry by cable, use cable as a handle, close door on cable, or pull cable around sharp edges or corners.»Keep cable away from heated surfaces.»To unplug, grasp the plug, not the cable.»Do not handle plug or appliance with wet hands.»Turn off all controls before unplugging.SAVE THESE INSTRUCTIONSORIGINAL INSTRUCTIONS. FOR OPERATION ON A 220-240 VOLT A.C. 50-60 HZ POWER SUPPLY ONLY.THIS MODEL IS FOR HOUSEHOLD USE ONLY.IMPORTANT INFORMATION»Keep appliance on a level surface.»To reduce the risk of a leaking condition, do not store machine where freezing may occur. Damage to internal components may result.2 3AssemblyNote: Always use genuine BISSELL® cleaning formulas for portable carpet and upholstery washers inyour machine.Spot & StainQuick andeffective spotcleaning.Pet Stain &OdourRemovestough petstains &odours.Stain PretreatLoosensset-in stains& odoursbefore carpetwashing.Pet StainPretreatLoosens toughpet stains& odoursbefore carpetwashing.Oxy BoostAdd toformula forpermanentstain removal. PretreatPretreat spots and stainsto improve cleaningperformance.FormulaKeep plenty of BISSELL cleaningformulas on hand so you can cleanwhenever it fits your schedule.BoostAdd to any formulato increase itseffectiveness.4 5IMPORTANT: Check the manufacturer’s tag before cleaning upholstery. If manufacturer’s tag is missing or not coded, check with your furniture dealer. Test a small, hidden area for colourfastness and examine when dry. If colour is aff ected do not use. Do not use on silk or velvet.6 7©2020 BISSELL Inc. All rights reserved. Part Number 1623999 07/20But wait, there’s more!Join us online for a complete guide to your new product, includingtroubleshooting, parts and more. Go to .VIDEOS INFO PARTSThis warranty gives you specific legal rights, in addition to rights you may have under the Australian Consumer Law . If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact your local BISSELL Consumer Care on the details set out below.It may be necessary to obtain some of yourpersonal information, such as a mailing address, to fulfill terms of this warranty. Any personal data will be handled pursuant to BISSELL’s Privacy Policy, which can be found at /privacy-policy.BISSELL® One Year WarrantySubject to the *conditions identified below, BISSELL will repair or replace (with new, refurbished, lightly used, or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for one years any defective or malfunctioning part due to manufacturerdefect. This warranty applies to product used for personal purposes, and not commercial or rental service. This warranty does not apply to fans or routine maintenance or consumable components such as filters, belts, brush rolls, etc., damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the user guide. BISSELL recommends that the original packaging be kept for the duration of the warranty period in case such need arises within the warranty period that the item needs re-packing and transportation.*Conditions of WarrantySubject to whether such loss is reasonably foreseeable, BISSELL and its in-country distributors are not liable for incidental orconsequential damages of any nature associated with the use of this product.For Australian Consumers Only: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law . You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.This guarantee is in addition to other rights or remedies under law. Nothing in this guarantee excludes, limits or modifies any liability of BISSELL which is imposed by law, or limits or modifies any remedy available to the consumer which is granted by law. To make a claim under this guarantee contact BISSELL Australia PTY LTD (details below). Contact BISSELL prior to returning any goods. Where agreed, BISSELL will reimburse reasonable postage / handling costs (if any) for returning goods to BISSELL. To claim expenses incurred in making a claim under this guarantee please provide BISSELL with a copy of the receipt of the expenses by email or post.Consumer CareAustraliaTelephone: 1300 247 735Website: .au New ZealandTelephone: 0800 247 735 Website: 。

目录1、设备介绍----------------------------------------------------------------------22、安全使用信息---------------------------------------------------------------43、操作----------------------------------------------------------------------------5 打开设备外包装--------------------------------------------------------------------5安装附件----------------------------------------------------------------------------5在水箱内注入操作用水------------------------------------------------------------7启动设备----------------------------------------------------------------------------7调节蒸汽喷出量--------------------------------------------------------------------7为设备续加操作用水---------------------------------------------------------------8 锁住设备----------------------------------------------------------------------------9关闭设备----------------------------------------------------------------------------9储存设备----------------------------------------------------------------------------94、操作信息---------------------------------------------------------------------9 清洁布制品-------------------------------------------------------------------------9清洁地毯或漆器表面-------------------------------------------- ------------------9清洁玻璃--------------------------------------------------------------------------105、如何使用配件-------------------------------------------------------------106、保养与维护-----------------------------------------------------------------12 清洁水箱---------------------------------------------------------------------------13保护绒布套------------------------------------------------------------------------147、故障排除--------------------------------------------------------------------148、安全部件---------------------------------------------------------------------15 压力控制开关-----------------------------------------------------------------------15低水位保护装置--------------------------------------------------------------------15安全保护装置-----------------------------------------------------------------------15安全锁------------------------------------------------------------------------------159、通用信息----------------------------------------------------------------------15 保修----------------------------------------------------------------------------------15废旧设备处理-----------------------------------------------------------------------1610、附件与零配件----------------------------------------------------------1611、技术参数----------------------------------------------------------------17在没有详细阅读产品使用说明，并了解使用情况之前，请不要使用设备，以免发生意外事故。

地毯说明书1. 产品介绍地毯是一种覆盖地面的装饰材料，具有保暖、减震、降噪等功能。

它可以用于家庭、办公室、酒店等各种场所，并且能够为房间增添美观和舒适感。

2. 材质选择地毯的材质种类繁多，常见的有羊毛、尼龙、聚酯纤维和丙烯纤维等。

不同材质的地毯具有各自的特点和用途，消费者可以根据自己的需求来选择合适的材质。

•羊毛地毯：具有良好的保暖性能和耐久性，但价格相对较高。

•尼龙地毯：耐磨性较强，易于清洁，并且价格适中。

•聚酯纤维地毯：具有良好的柔软度和色彩稳定性，但耐磨性较差。

•丙烯纤维地毯：价格相对较低，但耐久性一般。

3. 安装方法在安装地毯之前，需要确保地面平整、干燥和清洁。

安装地毯的方法有以下几种：•直接粘贴：适用于较小面积的地毯，将地毯背面的粘合剂涂抹在地面上，然后将地毯铺展开并压实。

•铺设垫子：适用于需要增加舒适感和保暖性的场所，先铺设一层垫子，再将地毯铺展在上面。

•固定脚钉：适用于需要固定地毯的场所，通过在地面上钉入脚钉来固定地毯。

4. 使用与保养为了延长地毯的使用寿命和保持其美观，需要进行定期清洁和保养。

•吸尘：每周至少进行一次吸尘，以去除灰尘和杂物。

•清洗：根据地毯材质选择合适的清洗方法，可以是干洗、湿洗或深层清洁。

•避免阳光直射：长时间暴露在阳光下会导致颜色褪色和纤维破坏，因此应避免阳光直射。

•频繁更换位置：如果家具经常放在同一个位置上，地毯可能会出现压痕，因此应定期更换家具的位置。

•避免使用尖锐物品：避免使用尖锐的物品刮擦地毯，以免损坏纤维。

5. 安全注意事项•防滑垫：在铺设地毯时，可以使用防滑垫来增加地毯的稳定性，避免滑倒。

•防火性能：选择具有良好防火性能的地毯，以确保安全。

•儿童和宠物：对于家中有儿童和宠物的消费者，应选择易清洁和耐磨的地毯，并定期清洁。

6. 注意事项•地毯色彩：由于不同材质和制造工艺的限制，地毯在颜色上可能会有些差异，请在购买前仔细查看样品或参考图片。

•尺寸误差：由于生产过程中存在一定的尺寸误差，请在购买前了解相关信息并预留合适的安装空间。

装饰工程使用说明书使用手册项目名称：xxxxxxxxxxxxxxxxxx装修工程建设单位：施工单位：管理单位：工程概况：本装修工程于2012年3月20日竣工交付使用。

为了保持装修材料的特性和特点，以下提出了几点日常维护注意事项和使用说明。

地毯：1.吸尘是地毯保养的基础工作，必须每天进行。

吸尘时，最好每个部位都吸遍，第一遍逆着地毯绒头吸，虽然用力大但可以吸尘彻底，第二遍顺着地毯绒头吸，可以使地毯恢复原来的绒头导向，避免绒头紊乱，造成地毯色差。

需要强调的是，无论吸尘进行几遍，最后一遍必须顺着绒头倒向吸。

公共区域地毯吸尘应使用带有旋转式绒头振动器的吸尘设备，进行日常吸尘清洁。

该振动器通常包括一个或多个毛刷条，更能有效地清除表面或深藏毯内灰尘。

2.定期对不同区域的地毯进行洗涤可以恢复地毯的原貌，延长其使用寿命。

地毯清洗有两种基本方法：干洗和湿洗。

无论选择哪种方法，洗涤地毯都需要受过良好职业培训的专业人员来进行。

1) 干洗干洗地毯有两种方法：泡沫干洗：这是一种最普遍的地毯表面泡沫清洗方法。

泡沫干洗机采用带有旋转毛刷和植入式湿性真空吸头，将大量洗涤剂喷洒在毯面绒头上。

在滚动毛刷的作用下，洗涤剂清洁绒头之后，用吸尘吸水机吸去洗涤泡沫和悬浮尘土。

干性提取清除法：该方法是通过人工或分配将溶剂、乳化剂、水和洗涤剂等混合物喷洒在地毯表面，经洗涤设备刷进地毯绒头中进行旋转洗涤30分钟后吸去洗剂及尘土。

干洗属于表面清洗，可以有效地使地毯表面恢复清洁，但并没有除去深藏在地毯里层污垢，要想彻底清洗，需要进行湿洗。

2) 湿洗当地毯的油污及其它粘性物质明显集结、灰尘污垢聚集已影响地毯色泽和地毯绒头回弹性能，而干洗法又无法根除时，就应进行地毯湿洗，即彻底清洗。

湿洗地毯有两种方法：喷吸清洗法：使用专业清洁设备，将清洁剂均匀喷洒在地毯上，然后用高压吸尘器将污垢和清洁剂一起吸走。

总之，地毯从使用的第一天开始，就需要每天彻底吸尘，不能等到灰尘沉淀堆积后再进行清洁。

使用说明书工程名称：根据本工程具体特点，现说明如下装修工程部分：1、吊顶工程（1）石膏板吊顶：因屋面为钢网架结构，考虑到防火要求，吊筋生根采用钻尾螺丝连接钢结构局部架设L40角钢，强度比膨胀螺栓钢筋砼连接要低，为非承重非上人吊顶，严禁上顶操作施工，吊筋严禁加设设备、电缆等重物，以免发生坠落危险或引起开裂等质量隐患。

（2）扣板吊顶采用企口卡槽连接，拆卸难度大，非专业人士严禁拆装，否则易引起板材变形、卡扣脱落发生坠落伤人危险。

严禁上人。

2、墙面工程（1）部分墙面为新做轻钢龙骨纸面石膏板隔墙，严禁打孔悬挂较重物体，严禁撞击及较大震动，以免对墙体造成破坏。

（2）墙面乳胶漆：严禁对墙面进行刮、碰、磕等破坏性行为，严禁对墙面洒水、浸泡，若墙面有粉尘浮土，请用干毛巾+鸡毛掸子+吸尘器进行处理。

（3）墙面壁纸：注意事项同乳胶漆。

如发现壁纸翘边严禁进行撕揭。

（4）玻璃隔墙：应设置防撞标志以防止因撞击导致玻璃破碎发生伤人，严禁对玻璃进行撞击，卫生清理时请使用专业保洁工具，严禁通过用吸盘、胶粘等方式悬挂重物。

对不锈钢严禁用利器刮擦。

（5）墙面瓷砖：因卫生间工作间隔墙均为后做保温板隔墙，墙面严禁重度震动，防止瓷砖坠落伤人。

（6）地面工程：地毯使用要求同酒店以下楼层。

瓷砖、石材地面严禁重物撞击。

安装工程：（1）电气工程：配电盘的配置及线路敷设等请查看安装工程设计图纸，以便于维修及检修线路。

电气设备接入时严禁过载，如发现异响、线路异常发热请切断电源，检查线路。

插座内严禁溅水发生短路。

（2）给排水工程：因为本工程为顶楼，冬季温度较低，我方为防止管道结冰冻裂管道已经做了保温处理但依旧有冻裂管道的隐患，为此我方建议建设单位冬季此楼层不用时请关闭阀门并将管道内积存水放净。

下水工程为后改造项目，管道弯头较多，请勿将垃圾、便纸及大的污物杂物等放入便池、斗、盆内，大小便及时冲刷。

另外工作间内橱柜下水未安装，请将下水口封好，防止堵塞。

其他工程：（1）橱柜：卫生间橱柜油漆面严禁磕碰，污物及时清理，大理石台面严禁滴沾油污。

吸尘器使用说明书本使用说明书旨在帮助用户正确、安全地使用吸尘器，并有效地清洁居室环境。

请在使用前仔细阅读说明书，并按照操作指南进行操作。

一、产品概述1. 本吸尘器采用先进的吸力技术，适用于各类地板、地毯、家具及其他家庭表面的清洁工作。

2. 产品外形美观大方，携带方便，是您日常清洁的好助手。

二、安全须知1. 使用前请确保电源插座与产品的电源线插头相匹配，注意电压稳定，以免发生电器故障。

2. 操作过程中请勿将吸尘器靠近明火或者高温物体，以免引起火灾或其他意外。

3. 注意保持插头及电源线干燥，避免受潮，以防电气短路。

三、准备工作1. 在开始吸尘前，请将家中的杂物整理干净，尽量清空各个清洁区域，以便提高吸力效果。

2. 检查吸尘器的滤芯是否装好，确保吸尘器吸力有效。

3. 根据需要选择合适的吸头和吸管，以便于清洁不同表面。

四、操作步骤1. 打开电源开关，启动吸尘器。

2. 将吸嘴贴近需要清洁的区域，保持吸嘴与地面平行，缓慢移动吸嘴，让吸尘器充分吸附尘垢。

3. 每次使用无需过度施力，凭借吸力即可轻松吸尘，如遇难清洁的区域，可适量增加吸力以提高效果。

4. 清洁结束后，及时关闭电源开关，停止吸尘器的运行。

五、清洁与维护1. 使用完毕后，请拔掉电源插头。

2. 清理吸尘器的滤芯和垃圾盒，并使用清水彻底清洗干净，但不可浸泡在水中。

3. 吸尘器的外壳可使用湿布擦拭，但请避免使用任何化学清洁剂。

4. 定期更换滤芯和清理吸嘴，以确保吸尘器的正常使用和清洁效果。

5. 请将吸尘器存放在干燥通风的地方，避免受潮或暴露在阳光下。

六、故障排除在使用吸尘器过程中，如果遇到以下故障，请先检查是否按照操作指南进行操作，并根据需要采取以下解决方案：1. 吸力不足：检查滤芯是否清洁，吸嘴是否堵塞，清理或更换相应部件。

2. 电源故障：检查电源线是否连接松动，电源插座是否正常，确保电源供应充足。

3. 异常噪音：检查吸嘴和吸管是否安装牢固，是否有异物卡住。