BJEU双旋流高效燃烧器安装操作说明书.

燃烧机的操作说明燃烧机整个操作过程中控制盒按既定先后次序支配不同的组件工作。

以下介绍c20燃烧机的操作过程和在草种特殊情形下控制盒作出的反应（以控制盒BE0LOA为准）（1）接通电源，燃烧机的马达转动，开始吹风程序。

油泵开始运行，但由于电磁油阀未通电，在吹风程序当中一直没有燃油输送至油嘴。

（2）点火用变压器亦财时通电，在点火电极前端产生电弧。

（3）吹风程序持续约13秒，然后电磁油阀通电打开而油泵输出燃油至油嘴，经雾化后喷出油雾，被点火电极前端的电弧点燃而形成火焰。

（4）在电磁油阀通电约2秒后，点火用变压器停止通电。

（5）如果是配用了恒温器，炉温升至恒温器所调校的温度时，燃烧机停止操作。

稍后当炉温下降而至恒温器上所调校的重开温度时，燃烧机恢复操作。

（注1）如果是采用单油管系统。

燃烧机在安装后第一次使用时，顺行进行排气。

（注2）如果喷出的油雾不能着火，眯炎用变压器是会维持较长的操作时间以帮助点火。

但如果在电磁油阀通电的10秒后仍然不能着火，低燃烧机会停止操作，控制盒亮起故障灯，如果输入至燃烧机的电压过低，这段10秒钟的时间是会变得较长。

（注3）燃烧机具有一项火焰监察功能，由控制盒配合感光电眼操作。

当燃烧机喷出火焰后，感觉电眼感应到火焰里的光，会将一个信号传送到控制盒，控制盒收到这个火焰信号，就会继续维持燃烧机的正常操作。

可是，如果因为某种原因而燃烧机不能喷出油雾，或喷出的油雾不能被燃点，控制盒在电磁油阀能电约10秒仍未收到火焰信号，就会停止燃烧机的操作，亮起故障灯，10秒称为（安全时间）而这项功能是必须要确知喷出的油雾能被燃点，不小不能被燃点的油雾继续在炉膛里积聚。

由于这项火焰监察功能感光电眼的感光部分必须经常保持清洁。

（注4）每次当故障灯亮起，须检查故障原因，整理妥当后，近下故障灯上的按钮，可重新开动燃烧机。

可是，每当故障灯亮起，最少亦需要50秒后才能按下按钮重新开动燃烧机。

（注5）感光电眼只应该在燃烧枫叶喷出火焰后才感应到火焰里的光。

BJEU双旋流高效燃烧器安装操作说明书北京益友科技有限公司目录1．设备编号2．工作原理3．安装4．操作5．维修6．图注附图：布置方式ⅠBJEU燃烧器结构Ⅱ调节装置Ⅲ刻度和长度补偿Ⅳ燃烧管更换Ⅴ示意图Ⅵ一次风比例示意图Ⅶ一次风冲量示意图Ⅷ1．设备编号BJEU-220-***2．工作原理BJEU型双旋流高效燃烧器是烧煤粉或煤粉和燃料油和/或燃气混烧的回转窑用燃烧器。

采用燃料混烧时必须使用燃油喷枪和/或燃气喷枪，以将燃料注入和雾化。

见相应设备说明书。

仅有一部分燃烧工艺所需的气流，即一次风，通过燃烧器。

一般情况下，一次风流量为7~8%Lmin（燃烧所需理论风量）。

一次风的压力为250mbar，出喷口速度200~210m/s。

2.1 燃烧器布置（附图Ⅰ）悬挂在移动小车（07）（见相关的操作说明书）上的燃烧器由一次风机（14）供给一次风。

另有一台专用冷却风机（13）在电源故障时确保燃烧器冷却。

2.2 见附图Ⅱ燃烧器通过支承管（21），与焊接在其上的悬挂梁上（23）相联。

支承管上设有一个进气口以导入外部一次风，或称轴流风。

燃烧器内装有一个中心管（33），根据具体应用，中心管内应有一个保护套管用以保护油/气喷嘴。

在煤粉入口区装有耐磨损衬里Densit。

此外，在进口端还装有一个带球阀（18）和软管（17）的管接头，用于从一次风机（14）的供风管上导入冷却风。

在出口端，带有小孔的喷嘴盘（41）起着提供冷却风的作用。

在中心管（33）向外，依次是煤粉管（34）、径向风管（35）和燃烧器外管。

中心管（33）向内，依次是二次增强旋风管（33a），及油枪护管（33b），点火油枪从油枪护管（33c）中穿过。

粉煤管（34）通过筋板与中心管（33）相触。

燃烧器（30）的出口端是经过机加工过的锥形燃烧器喷嘴（27）。

在进口端，用法兰与煤粉管进口（25）相联。

里面镶有Densit 耐磨衬里。

此外，煤粉管用膨胀节（44）与径向风管（35）相连。

燃烧器操作说明一、 初次使用，检查程序：遵循锅炉制造商的使用说明确认系统有足够多的水，油箱满油确认燃烧系统电控柜接线正确检查燃烧器电机转向检查温度、压力等传感器设定油路排气确保无空气检查油箱、油管、油泵充满油，喷嘴选择正确检查油路是否有泄露燃烧器处于开启位置，风门处于关闭位置程控器闭合，程控器处于启动位置二、 油路系统检查断开油路卸下电磁阀和喷嘴间连接启动燃烧器检查是否安程序控制器既定程序运行1、鼓风机气动2、风门伺服电机运行到最大位置3、风压监测正常4、风门伺服电机返回到点火位置5、点火6、油电磁阀打开7、安全时间后报警重新装好连接件三、 比例调节器回油与空气流量调节卸下风门伺服电机与比例调节器上的连接，启动燃烧器，点火后手动设定燃烧器负荷在最小位置，检查燃油和风量配合效果。

顺时针转动= 增加风量逆时针转动= 降低风量注意：燃烧器启动后调节风压开关，如果设定值过高，风压开关会自动保护，设定风压保护值一定要合理。

测量点火位置油消耗量1、通过流量表2、根据供油压力和喷嘴型号按照曲线图测算调节点火位置油量1、若喷油量过低，将伺服电机逐步增大到规定值2、若喷油量过高，现将最低油量限位开关调低，再逐步降低风门伺服电机，直至达到规定值。

调整过程中注意燃烧器的燃烧情况，如有必要从新调整。

调整满负荷耗油量逐步增大风门伺服电机的位置直至满负荷，调整过程中观察火焰燃烧情况，如有必要从新进行调整。

测量满负荷位置油消耗量1、通过流量表2、根据供油压力和喷嘴型号按照曲线图测算调节满负荷油流量若满负荷油量过多，减小风门伺服电机开度，直至达到规定值注意：不允许通过调节连杆降低油流量，以免影响低负荷燃烧状况。

若满负荷油量过低，首先增大限位开关的位置，然后调节伺服电机的开度，直至达到规定值，调节过程中注意观察火焰燃烧情况，如有必要从新进行调整。

风量调节风门伺服电机出厂设定值为：满负荷时全开，低负荷时全关，未达到最佳的燃烧效果，应从低负荷位置逐步调整燃油与风量的配比。

燃烧器操作说明一、 初次使用，检查程序：遵循锅炉制造商的使用说明确认系统有足够多的水，油箱满油确认燃烧系统电控柜接线正确检查燃烧器电机转向检查温度、压力等传感器设定油路排气确保无空气检查油箱、油管、油泵充满油，喷嘴选择正确检查油路是否有泄露燃烧器处于开启位置，风门处于关闭位置程控器闭合，程控器处于启动位置二、 油路系统检查断开油路卸下电磁阀和喷嘴间连接启动燃烧器检查是否安程序控制器既定程序运行1、鼓风机气动2、风门伺服电机运行到最大位置3、风压监测正常4、风门伺服电机返回到点火位置5、点火6、油电磁阀打开7、安全时间后报警重新装好连接件三、 比例调节器回油与空气流量调节卸下风门伺服电机与比例调节器上的连接，启动燃烧器，点火后手动设定燃烧器负荷在最小位置，检查燃油和风量配合效果。

顺时针转动= 增加风量逆时针转动= 降低风量注意：燃烧器启动后调节风压开关，如果设定值过高，风压开关会自动保护，设定风压保护值一定要合理。

测量点火位置油消耗量1、通过流量表2、根据供油压力和喷嘴型号按照曲线图测算调节点火位置油量1、若喷油量过低，将伺服电机逐步增大到规定值2、若喷油量过高，现将最低油量限位开关调低，再逐步降低风门伺服电机，直至达到规定值。

调整过程中注意燃烧器的燃烧情况，如有必要从新调整。

调整满负荷耗油量逐步增大风门伺服电机的位置直至满负荷，调整过程中观察火焰燃烧情况，如有必要从新进行调整。

测量满负荷位置油消耗量1、通过流量表2、根据供油压力和喷嘴型号按照曲线图测算调节满负荷油流量若满负荷油量过多，减小风门伺服电机开度，直至达到规定值注意：不允许通过调节连杆降低油流量，以免影响低负荷燃烧状况。

若满负荷油量过低，首先增大限位开关的位置，然后调节伺服电机的开度，直至达到规定值，调节过程中注意观察火焰燃烧情况，如有必要从新进行调整。

风量调节风门伺服电机出厂设定值为：满负荷时全开，低负荷时全关，未达到最佳的燃烧效果，应从低负荷位置逐步调整燃油与风量的配比。

说明书摘要本实用新型涉及的是一种工业窑炉使用的燃烧器（如水泥回转窑用煤粉燃烧器）。

它包括中心点火油枪1、内旋流风通道2、煤粉通道4、外旋流风通道5、直流风通道7和耐火浇注料9。

直流风通道7由燃烧器头部若干均匀分布的小孔8组成，外旋流风通道5位于煤粉通道4的外侧，内旋流风通道2位于煤粉通道4的内侧，中心通道为点火油枪1。

内旋流风通道2和外旋流风通道5由同一个风机供风，并在进内、外旋流风通道的连接管上分别装上阀门，用于调节内、外旋流风的比例，从而可以有效地改变燃烧器的旋流强度，达到在较大范围内调节火焰形状，适应各种燃料燃烧的要求。

该燃烧器不仅可以使用优质烟煤、劣质烟煤、无烟煤甚至其它固体可燃物，而且燃尽率高，同时能大幅度地降低有害气体(NOx)的排放量。

摘要附图权利要求书1、一种双旋流多通道燃烧器，它包括有中心点火油枪、旋流风通道、煤粉通道、直流风通道及喷嘴孔、耐火浇注料，其特征在于在煤粉通道4的内侧和外侧分别设有环形内旋流风通道和环形外旋流风通道，在内、外旋流风通道热端各装一旋流器。

2、根据权利要求1所述的双旋流多通道燃烧器，其特征在于内、外旋流器为环形螺旋叶片状，其旋流角度是0至50o。

3、根据权利要求1或2所述的双旋流多通道燃烧器，其特征在于内旋流器的角度与外旋流器的角度相同或不同。

4、根据权利要求3所述的双旋流多通道燃烧器，其特征在于在于内、外旋流风通道上分别设有风量调节阀门。

说明书双旋流多通道燃烧器涉及领域本实用新型涉及的是一种将固体燃料（如烟煤、劣质煤、无烟煤等）喷入工业窑炉（如水泥回转窑）内产生高温火焰的燃烧器，特别为一种双旋流多通道燃烧器。

背景技术目前传统燃烧器经过了单通道、二通道、三通道的发展过程。

二通道燃烧器是在早期单通道燃烧器基础上增加了中心一次风通道区，相对单通道燃烧器而言，二通道燃烧器具有调节灵活、火焰粗短且温度高的特点，但其火焰不很集中、一次风用量大、煤种适应性差。

为此在二通道燃烧器的煤粉通道外侧在增加一环形通道成为三通道燃烧器。

2 Burner Gas GriddleModel# TGG02TSupplier Model# SRGG21706User’s ManualWhen using this appliance, basic safety precautions should always be observed. Read andunderstand the meaning of these symbols before assembling and using this appliance.SAFETY SYMBOLS: DANGERIndicates a hazardous situation, which if not avoided, will result in death or serious injury.WARNINGBe alert to the possibility of serious personal injury if the instructions are not followed.CAUTIONIndicates a potentially hazardous situation, which if not avoided, could result in moderate injury.CAUTION This instruction manual contains important information necessary for the proper assembly and saf using the appliance. Follow all warnings and instructions when using the appliance.e use of the appliance. Read and follow all warnings and instructions before assembling andWarnings...............................................................................................2, 4-8Parts List (11)Assembly Instructions (12)Troubleshooting (15)Care and Maintenance (13)Warranty Information..................................................................................15NOTE: Before beginning assembly of product, make sure all parts are present. Compare parts with package content list and hardware contents.If any part is missing or damaged do not attempt to assemble the unit.Contact customer service for replacement parts.Exploded View (10)Operating Instructions (8)Product Dimension (9)Failure to follow these instructions and warnings could result cause property damage, personal injury or even death. Using an LP appliance has a degree of risk that •DO NOT USE ON SURFACES such as wood, asphalt or plastic. These surfaces are combustible•Hot cooking liquids can remain dangerously hot long after cooking. NEVER handle the cooking •Do not move the appliance when in use.Equipped for use on: Propane. Main Max. Input Rating: 17,000 BTU/HOutdoor Cooking Specialty Gas Appliance WARNING: FOR OUTDOOR USE ONLY . If stored indoors, detach and leave cylinder outdoors. Minimum clearance from sides and back of unit to combustible construction: 24 inches from sides and 36 inches from back. The appliance shall not be located or used under overhead unprotected combustible construction.WARNING: This appliance comes with a supplied CSA approved regulator which mustbe used with this appliance. Replace only with regulator Model No. RY0505D or GR-148.CAUTION: The instruction manual contains important information necessary for the properassembly and safe use of the appliance. Read and follow all warnings and instructions beforeassembling and using the appliance. Follow all warnings and instructions when using the appliance. If instructions or parts are missing contact customer service.This appliance is not designed nor intended for commercial use. If you smell gas: If possible, immediately turn off gas supply to the appliance by turning the LP tankvalve clockwise (right). If this cannot be accomplished safely, immediately get away from the appliance appliance until the cooking liquid has cooled to less than 115˚F (45˚C).•This appliance will be hot during and after e insulated oven mitts or gloves to protect from hot surfaces or splatter from cooking liquids. Closed toed shoes should always be worn during operation of this appliance.•Keep children and pets away from the cooking appliance at all times.•The use of alcohol, prescription drugs or non-prescription drugs may impair the consumer's ability to properly assemble or safely operate the appliance. Do not operate when u•The minimum outside operating temperature of this appliance is 32˚F (0˚C). NEVER use this appliance when temperature is below this minimum.•Take CAUTION when in close proximity to appliance. Falling or tripping near the gas appliance may result in the splashing or igniting of hot cooking liquids and potentially cause personal injury or property damage.•This appliance is NOT intended for commercial use.•The installation must conform with local codes or, in the absence of local codes, with the National FuelGas Code, ANSI Z223.1/NFPA 54, Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58; or Natural Gas and Propane Installation Code, CSA B149.1; Propane Storage and Handling, CSA B149.2.•NEVER operate this appliance indoors or any enclosed area. This appliance should ONLY be used outdoors. The appliance shall not be used in a building, garage or any other enclosed area.•NEVER install or use this appliance on a boat or other recreational vehicles.•This product is NOT designed to be used as a heater. NEVER use this appliance as a source of heat.•Introduction of water or ice from any source into the oil/grease may cause overflow and severe burns from hot oil and water splatter.•When cooking, the appliance must always be on a level, stable, non-combustible surface such as brick, concrete, or dirt. NEVER use this appliance around surfaces such as asphalt, wood, dry grass or leaves, vinyl or plastic.•Keep the fuel supply hose away from any heated surfaces.•NEVER attempt to attach this appliance to the self-contained LP gas system of a camper, trailer or motor home. The pressure regulator and hose assembly supplied with the appliance MUST BE THE ONE USED. Replacement hose assembly must be GA09 or WG01.•Check and clean burner/venturi tubes for insects and insect nesbeneath the appliance.••Maintain proper clearances from combustible construction. Minimum clearance from sides and back of unit to combustible construction: 24 inches from sides and 36 inches from back.•Do not leave the appliance unattended. Keep children and pet •When cooking with oil or grease, have a type BC or ABC fire extinguisher readily available.•In the event of an oil or grease fire do not attempt to extinguish with water. Immediately call the fire department. A Type BC or ABC fire extinguisher may, in some circumstances contain the fire.WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, and carbon monoxide, which is known to the State of California to cause birth defects or other reproductive harm. For more information, go to .s away from the appliance at all times. tilation.!LP TANK REMOVAL, TRANSPORT AND STORAGE:1.Turn control knobs to OFF position.2.20Lb. cylinder: Turn off the cylinder valve. Turn coupling nut counterclockwise by hand only.NEVER use tools to disconnect. When the appliance is not in use, the gas must be turned off at the supply cylinder.3.1Lb. cylinder: Rotate LP gas tank counter-clockwise until it is loose. NEVER use tools to disconnect. The cylinder must be disconnected when the appliance is not in use.1.Do not store a spare LP gas cylinder under or near this appliance.2.NEVER fill the cylinder beyond 80 percent full.3.If the instructions in 1 and 2 are not followed exactly, a fire causing death or serious injury may occur.4.The safety release valve on the LP tank could activate the leaking of gas and cause a severe fire and increase the risk of serious injury or death.5.If you smell, see or hear leaking gas IMMEDIATELY get away from the LP tank and contact your FIRE DEPARTMENT.4.Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane.5.A disconnected LP tank in storage or being transported must have a safety cap installed.NEVER leave an LP tank in a car that can become overheated by the sun.6.The cylinder must be stored outdoors out of the reach of children. NEVER store the cylinder in enclosed spaces such as a garage, carport, covered porch or any other structure.7.Storage of an appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance.LP TANK:The LP tank must meet the following requirements in order to be used with your appliance:••Measurements must be 12” (30.5cm) in diameter by 18” (45.7cm) high with 20lb. (9.1kg)maximum capacity.Measurements must be 3.858" (9.8cm) in diameter by 7.874" (20cm) high with 1lb. (16.4oz) maximum capacity.••The LP gas supply cylinder must be constructed and marked in accordance with theNational Standard of Canada (CAN/CSA-B339), Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods.Only cylinders marked "propane" shall be used.The 20Lb. LP tank must include the following:•QCC Type 1 outlet compatible with regulator or appliance.•Safety relief valve.•hand wheel. Only use tanks equipped with this type of valve. •LP tank must be arranged for vapor withdrawal and include collar that protects LP tank valve.•LP gas is odorless, non-toxic, and colorless when produced. For your safety, LP gas has been given an odor (similar to rotten eggs) so you can smell if there is any leaking.• DANGER Indicates a hazardous situation, which if not avoided, will result in death or serious injury.CONNECTING HOSE ASSEMBLY TO 20LB. CYLINDER:1.Make sure cylinder valve is turned OFF (turning clockwise).2.Check cylinder valve to ensure it has proper externalmale threads as illustration(type 1 ANSI Z21.81).3.Make sure all burner valves are in the OFF positions.4.Inspect valve connections, port and regulatorassembly. Look for any damage or debris. Remove any debris. Inspect hose for damage.Never attempt to use damaged or obstructed equipment. See your local LP gas dealer for repair.5.When connecting hose assembly to the cylinder valve, do so manually, do not use a tool. Tighten6.SLOWLY - Open the cylinder valve fully. Proceedto a leak test (see LEAK TESTING section).1.Make sure all control knobs are in the OFF positions.2.for repair.3.a serious risk of gas leak.4.Proceed to a leak test (see LEAK TESTING section).LEAK TESTING VALVES, HOSE AND REGULATOR • •DO NOT smoke or have anything nearby that can easily ignite, such as lighters or matches.• •Appliance must be leak checked outdoors in a well-ventilated area away from open flames or sparks.STEPS TO LEAK TEST:e a clean paint brush and 50/50 soap and water solution.NOTE: Use a mild soap and water. DO NOT use household cleaning agents. Damage to gas train components could result.2.Brush soapy solution onto all metal seams and entire valve area. Slowly turn the LP tank valveimmediately turn the valve off by turning clockwise. After 10 seconds, turn the LP tank to the off position and continue to watch for any bubbles. UNDER NO CIRCUMSTANCE SHOULD THE VALVE REMAIN IN THE ON POSITION FOR MORE THAN 12 SECONDS.3.If bubbles are observed at the valve attachment, you may attempt to tighten the valve, and repeat 4.Brush soapy solution onto indicated connections as shownthe test from the beginning after waiting 5 minutes.5.If "growing" bubbles appear, there is a leak. Close LP tank valve immediately and retighten connections. If leaks cannot be stopped, do not try to repair. Call for replacement parts.6.For assistance with any malfunction related to the LP tank, regulator or hose, contact yourpropane dealer or customer service.W !ARNING If growing bubbles begin to appear there is a leak. IMMEDIATELY turnoff LP tank valve. If bubbles continue, IMMEDIATELY get away from theLP tank and contact your FIRE DEPARTMENT (e.g. 911)External threadsOPD triangular handleFix hose clockwiseINSTRUCTIONS FOR LIGHTING BURNER:1.Read all instructions before lighting.2.Make sure all control knobs are in the OFF position.3.When use 20lb. cylinder: Turn on the cylinder valve.4.Select the burner to be lit. Push and turn the control knob of that burner counter-clockwise to HIGH. Hold the control knob pushed down for 2-3 seconds. It will light the burner.5.Adjust the flame by turning control knob between HIGH and LOW.6.Repeat step 4 for lighting other burner.7.If ignition does not occur in 5 seconds, turn the burner control(s) OFF, wait 5 minutes, and repeat the lighting procedure.MANUAL LIGHTING 1.Make sure all control knobs are in the OFF position.2.When use 20lb. cylinder: Turn on the cylinder valve.3.Remove the cooking plate. Insert a match into the match lighter.Strike the match and place near the gas outlet openings on the burner. Push and turn the control knob of that burner counter-clockwise to HIGH. Hold the control knob pushed down for 2-3 seconds. It will light the burner.4.Adjust the flame by turning control knob between HIGH and LOW.5.Repeat step 3 for lighting other burner.6.If ignition does not occur in 5 seconds, turn the burner control(s)OFF, wait 5 minutes, and repeat the lighting procedure.7.Place the cooking plate back onto the griddle body.Note: Match lighter is attached to the main valve tube at the bottom of gas griddle.by the manufacturer. Place the match lighter on the platform of the control panel after use.SHUT DOWN INSTRUCTIONS 2.20LB. cylinder: Turn LP cylinder gas valve clockwise to OFF position when griddle is not in use.1LB cylinder: Turn the cylinder counter-clockwise to disconnect cylinder from regulator when griddle is not in use.1.Push and turn control knob clockwise to OFF position.WHEN THE BURNER FLAME IS ACCIDENTALLY EXTINGUISHED 1.Close the LP tank valve.2.Push and turn control knob clockwise to OFF position.3.Inspect if the hose etc. connections are good, wait 5 minutes. After waiting 5 minutes, re-start the appliance following the lighting instructions.REGULATOR HOSE ASSEMBLY CHECK:WARNING Before each use, check to see if there is evidence of abrasion, wear, cuts or leaks on the hose. Ifdamage is evident, the hose must be replaced prior to appliance use.PRODUCT DIMENSION18.3"4.3"9"18 .5"456321Part #DescriptionImageQty1Griddle body 1123Cooking Plate NOTE: Wash all parts that will come in contact with food or water with warm soapy water, rinse and towel dry.4Adjustable Feet 45Regulator Assembly 16Hose Assembly 1Grease Box 1HOW TO CLEAN:Proper care and appliance maintenance will keep your product operating smoothl Keep appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.Keep the ventilation opening(s) of the cylinder enclosure free and clear from debris.NOT obstruct the flow of combustion and ventilation air.Check for proper burner flame characteristics. Each burner is adjusted prior to shipment; however, variations in the local gas supply may take minor adjustments.Burner flames should be blue and stable with no yellow tips, excessive noise, or lifting. Slight yellow tipping is normal for LP gas.If the flame is yellow, itindicates insufficient air. If the flame is noisy and tends to lift away from the burner, it indicates too much air.Visually check the burner flames prior to each use,the flames should look like this picture, if flames do not, send mail to our customer service: *******************BURNER FLAME CHECKy.CLEAN THOROUGHLY AFTER EVERY USE.NOTE: Clean the entire appliance each year and tighten all hardware on a regular basis (1-2 times a year or more depending on amount of use).1.Before cleaning turn off the appliance at the gas cylinder. Check that there is no flame, gas smell and the valves are in off position. Next, make sure unit is properly disconnected from propane tank prior to any cleaning.2.Everything that was in contact with the food must be hand washed with warm soapy water and nylon pad. DO NOT spray oven cleaner on cooking plate to remove grease or soot. It will cause the finish to become dull. If food remains stuck to the cooking plate, add hot water and let it soak,after cooling, scrub with steel wool.3.lacing in storage.4.We recommend that the unit be thoroughly cleaned prior to every use.5.Store all components in a dry location when not in use.Forreplacementparts,************************************************************The regulator should be hung on the gas griddle to prevent it from being damaged.CAUTION!Allow unit to fully cool (115˚F or 45˚C) before performing any cleaning.SUGGESTED CLEANING MATERIALS:•Hot water•Mild dishwashing liquid detergent•Soft, nylon cleaning pad CLEANING BURNERSProblems Possible causes SolutionsBurners can’t be lit by the existing ignition system 1/ LPG gas bottle is empty2/ Faulty regulator3/ Obstructions in the burners4/ Obstructions in gas pipe orhose1/ Replace with full bottle2/ Check or replace theregulator3/ Clean burners4/ Clean gas pipe or hoseBurners can’t be lit by a match 1/ LPG gas bottle is empty2/ Faulty regulator3/ Obstructions in the burners4/ Obstructions in gas pipe orhose 1/ Replace with full bottle 2/ Check or replace the regulator3/ Clean burners4/ Clean gas pipe or hoseWeak flame or backfire (Fire inside the burner - you can hear a whistling or rusting noise) 1/ LPG gas bottle is too small2/ Obstructions in the burners3/ Obstructions in gas pipe orhose4/ Windy weather1/ Use a bigger bottle2/ Clean burners3/ Clean gas pipe or hose4/ Place the griddle in a moreprotected placeControl knob is difficult to turn 1/ Windy weather Replace the gas valveWhat is covered under this warranty?This product is covered under the Manufacturers Limited Warranty. To ensure your complete satisfaction, this warrants to the original purchaser that this griddle is free from defects in material and workmanship as of the date of purchase and that it will, under normal use and proper care, remain so for one year after the date of purchase. Replacement of missing or initially defective parts will be sent at no charge for a period of 10 days from date of purchase. The manufacturer and retailer will not be responsible for missing parts and/or hardware after 10 days from date of purchase.Warranty does not cover:Freight and packaging charges to and from our customer service center remain the customer’s responsibil- ity. Labor or material charges to remove or replace parts are not covered under this warranty. Any floor sample sales or clearance sales from the store are not covered by this warranty. Furniture used for com-mercial purposes; failures caused by improper care; unreasonable or abusive use; damage by modification or alteration; freeze damage; acts of nature; rust; fabric stains; ripping or fading; purchased parts; or return freight and packaging charges are not covered under this warranty. Proof of purchase (dated register receipt) is required for warranty claims.How to obtain service: Ifyouhaveanyquestionsorconcernspleasecontactcustomerservice:*******************SHENZHEN AUKEYHI TECHNOLOGY CO., LTD.ROOM 201, BLOCK A, NO.1, QIANWAN ROAD 1, QIANHAISHENGANG COOPERATIVE DISTRICT, SHENZHEN, CHINAWEB：EMAIL：SUPPORT@FACEBOOK：HTTPS:/// INSTAGRAM： HTTPS:///。

煤粉燃烧器<使用说明书>扬州市银焰机械厂尊敬的用户朋友：您好！感谢您及贵公司（厂）对“银焰”牌产品的信任和支持，选择使用“银焰”牌燃烧器装置，这是“银焰”人的集体荣耀。

“银焰”全体职工向您道声“谢谢”！如果您有什么建议和要求，请及时告诉我们，我们将把您的建议和要求作为下一步努力的目标和方向。

我们永远奉行“质量是生命，用户是上帝”的宗旨，竭诚为您提供周到、满意的服务。

扬州市银焰机械厂厂长：韦维通迅地址：江苏省扬州市产陵产业园银焰路9号电话：0514-*******-8811传真：0514-*******邮编：225006目录1、概述--------------------------------------12、结构简图及主要尺寸--------------------------------------23、结构及特点-------------------------------------------2-54、工作原理-----------------------------------------------65、安装---------------------------------------------------66、操作要求---------------------------------------------7-11 6．1操作------------------------------------------------7-9 6．1．1火焰形状的调整-----------------------------------7-9 6．1．2燃烧器位置的调整-----------------------------------9 6．2点火--------------------------------------------------10 6．3停窑--------------------------------------------------117、检查及保养---------------------------------------------128、常见故障及处理-----------------------------------------139、其它---------------------------------------------------141、概述煤粉燃烧器是水泥企业熟料烧成系统中的关键设备，其性能及操作的好坏关系到熟料产量、质量、能耗和环保，回转窑耐火砖的使用寿命长短等一系列问题，也就是说性能质量优良的煤粉燃烧器，将给企业带来巨大的经济效益，反之，将会带来无法估计的经济损失，因此煤粉燃烧器倍受水泥企业管理者和技术人员的高度重视！我厂在消化吸收国内外多风道煤粉燃烧器特点的基础上，集众家之长，研制的多风道燃烧器性能优越，可适合于各类回转窑，总体性能达到国际同类产品先进水平。