变电站外文翻译外文文献英文文献变电站的综合概述

附录Ⅲ英文翻译A comprehensive overview of substationsAlong with the economic development and the modern industry developments of quick rising, the design of the power supply system become more and more completely and system. Because the quickly increase electricity of factories, it also increases seriously to the dependable index of the economic condition, power supply in quantity. Therefore they need the higher and more perfect request to the power supply. Whether Design reasonable, not only affect directly the base investment and circulate the expenses with have the metal depletion in colour metal, but also will reflect the dependable in power supply and the safe in many facts. In a word, it is close with the economic performance and the safety of the people. The substation is an importance part of the electric power system, it is consisted of the electric appliances equipments and the Transmission and the Distribution. It obtains the electric power from the electric power system, through its function of transformation and assign, transport and safety. Then transport the power to every place with safe, dependable, and economical. As an important part of power’s transport and control, the transformer substation must change the mode of the traditional design and control, then can adapt to the modern electric power system, the development of modern industry and the of trend of the society life.Electric power industry is one of the foundations of national industry and national economic development to industry, it is a coal, oil, natural gas, hydropower, nuclear power, wind power and other energy conversion into electrical energy of the secondary energy industry, it for the other departments of the national economy fast and stable development of the provision of adequate power, and its level of development is a reflection of the country's economic development an important indicator of the level. As the power in the industry and the importance of the national economy, electricity transmission and distribution of electric energy used in these areas is an indispensable component.。

变电站建设外文文献翻译变电站建设外文文献翻译(文档含中英文对照即英文原文和中文翻译)General Requirements to Construction of SubstationSubstations are a vital element in a power supply system of industrial enterprises．They serve to receive ，convert and distribute electric energy .Depending on power and purpose ,the substations are divided into central distribution substations for a voltage of 110-500kV;main step-down substations for110-220/6-10-35kV;deep entrance substations for 110-330/6-10Kv;distribution substations for 6-10Kv;shop transformer substations for 6-10/0.38-0.66kV.At the main step-down substations, the energy received from the power source is transformed from 110-220kV usually to 6-10kV(sometimes 35kV) which is distributed among substations of the enterprise and is fed to high-voltage services.Central distribution substations receive energy from power systems and distribute it (without or with partial transformation) via aerial and cable lines of deep entrances at a voltage of 110-220kV over the enterprise territory .Central distribution substation differs from the main distribution substation in a higher power and in that bulk of its power is at a voltage of 110-220kV;it features simplified switching circuits at primary voltage; it is fed from the power to an individual object or region .Low-and medium-power shop substations transform energy from 6-10kV to a secondary voltage of 380/220 or 660/380.Step-up transformer substations are used at power plants for transformation of energy produced by the generators to a higher voltage which decreases losses at a long-distancetransmission .Converter substations are intended to convert AC to DC (sometimes vice versa) and to convert energy of one frequency to another .Converter substations with semiconductor rectifiers are convert energy of one frequency to another .Converter substations with semiconductor rectifiers are most economic. Distribution substations for 6-10kV are fed primarily from main distribution substations (sometimes from central distribution substations).With a system of dividing substations for 110-220kV, the functions of a switch-gear are accomplished by switch-gears for 6-10kV at deep entrance substations.Depending on location of substations their switch-gear may be outdoor or indoor. The feed and output lines at 6-10kV substations are mainly of the cable type .at 35-220kV substations of the aerial type .When erecting and wiring thesubstations ,major attention is given to reliable and economic power supply of a given production.Substations are erected by industrial methods with the use of large blocks and assemblies prepared at the site shops of electric engineering organizations and factories of electrical engineering industry .Substations are usually designed for operation without continuous attendance of the duty personnel but with the use of elementary automatic and signaling devices.When constructing the structural part of a substation .it is advisable to use light-weight industrial structures and elements (panels ,floors ,etc.) made of bent sections .These elements are pre-made outside the erection zone and are only assembled at site .This considerably cuts the terms and cost of construction.Basic circuitry concepts of substations are chosen when designing a powersupply system of the enterprise .Substationsfeature primary voltage entrances .transformers and output cable lines or current conductors of secondary voltage .Substations are mounted from equipment and elements described below .The number of possible combinations of equipment and elements is very great .Whenelaborating a substation circuitry ,it is necessary to strive for maximum simplification and minimizing the number of switching devices .Such substations are more reliable and economic .Circuitry is simplified by using automatic reclosure or automatic change over to reserve facility which allows rapid and faultless redundancy of individual elements and using equipment.When designing transformer substations of industrial enterprises for all voltages ,the following basic considerations are taken into account:1. Preferable employment of a single-bus system with using two-bus systems only to ensure a reliable and economic power supply;2. Wide use of unitized constructions and busless substations;3.Substantiated employment of automatics and telemetry ;if the substation design does not envisage the use of automatics or telemetry ,the circuitry is so arranged as to allow for adding such equipment in future without excessive investments and re-work./doc/554c0a220622192e453610661ed9ad5 1f01d5431.html e of simple and cheap devices-isolating switches ,short-circuiting switches ,load-breaking isolators ,fuses ,with due regard for their switching capacity may drastically cut the need for expensive and critical oil ,vacuum ,solenoid and air switches .Substation and switch-gear circuitries are so made that using the equipment of eachproduction line is fed from individual transformers ,assemblies ,the lines to allow their disconnection simultaneously with mechanisms without disrupting operation of adjacent production flows.When elaborating circuitry of a substation, the most vital task is to properly choose and arrange switching devices(switches ,isolators ,current limiters ,arresters ,high-voltage fuses).The decision depends on the purpose ,power and significance of the substation.Many years ago, scientists had very vague ideas about electricity. Many of them thought of it as a sort of fluid that flowed through wires as water flows through pipes, but they could not understand what made it flow. Many of them felt that electricity was made up of tiny particles of some kind ,but trying to separate electricity intoindividual particles baffled them.Then, the great American scientist Millikan, in 1909,astounded the scientific world by actually weighing a single particle of electricity and calculating its electric charge. This was probably one of the most delicate weighing jobs ever done by man,for a single electric particle weighs only about half of a millionth of a pound. To make up a pound it would take more of those particles than there are drops of water in the Atlantic Ocean.They are no strangers to us, these electric particles, for we know them as electrons. When large numbers of electrons break away from their atoms and move through a wire,we describe this action by saying that electricity is flowing through the wire.Yes,the electrical fluid that early scientists talked about is nothing more than electrical flowing along a wire.But how can individual electrons be made to break awayfrom atoms? And how can these free electrons be made to along a wire? The answer to the first question lies in the structure of the atoms themselves. Some atoms are so constructed that they lose electrons easily. An atom of copper, for example ,is continually losing an electron, regaining it(or another electron),and losing it again. A copper atom normally has 29 electrons, arranged in four different orbits about its nucleus. The inside orbit has 2 electrons. The next larger orbit has 8.The third orbit is packed with 18 electrons . And the outside orbit has only one electron.It is this outside electron that the copper atom is continually losing, for it is not very closely tied to the atom. It wanders off, is replaced by another free-roving electron, and then this second electron also wandersaway.Consequently,in a copper wire free electrons are floating around in all directions among the copper atoms.Thus, even through the copper wire looks quite motionless to your ordinary eye, there is a great deal of activity going on inside it. If the wire were carrying electricity to an electric light or to some other electrical device, the electrons would not be moving around at random. Instead, many of them would be rushing in the same direction-from one end of the wire to the other.This brings us to the second question .How can free electrons be made to move along a wire? Well ,men have found several ways to do that .One way is chemical. V olta,s voltaic pile,or battery, is a chemical device that makes electricity(or electrons)flow in wires. Another way is magnetic. Faraday and Henry discovered how magnets could be used to make electricity flow in a wire.MagnetsAlmost everyone has seen horseshoe magnets-so called because they are shaped like horseshoes. Probably you have experimented with a magnet, and noticed how it will pick up tacks and nails, or other small iron objects. Men have known about magnets for thousands of years.Several thousand years ago, according to legend, a shepherd named Magnes lived on the island of Crete, in the Mediterranean Sea .He had a shepherds crook tipped with iron. One day he found an oddly shaped black stone that stuck to this iron /doc/554c0a220622192e453610661ed9ad51f0 1d5431.html ter, when many other such stones were found, they were called magnets(after Magnets).These were natural magnets.In recent times men have learned how to make magnets out of iron. More important still, they have discovered how to use magnets to push electrons through wires-that is, how to make electricity flow. Before we discuss this, there arecertain characteristics of magnets that we should know about.If a piece of glass is laid on top of a horse- shoes magnet, and if iron filings are then sprink ledon the glass, the filings will arrange themselves into lines. If this same thing is trid with a bar magnet(a horseshoe magnet straightened out),the lines can be seen more easily. These experiments demonstrate what scientists call magnetic lines of force. Magnets, they explain, work through lines of force that ext- end between the two ends of the magnet. But electrons seem to have magnetic lines of force around them, too.This can be proved by sticking a wire through a piece ofcard board, sprinkling iron filings on the cardboard, and connecting a battery to the wire. The filings will tend to form rings around the wire,as a result of the magnetism of the moving electrons(or electricity).So we can see that there is arelationship betweenmoving electrons and magnetism, Magnetism results from the movement of electrons.Of course, electrons are not really flowing in the bar magnet, but they are in motion, circling the nuclei of the iron atoms. However, in the magnet, circling thelined up in such a way that their electrons are circling in the same direction. Perhaps a good comparison might be a great number of boys whirling balls onstrings in a clockwise direction around their heads.翻译：变电站建设的一般要求变电站(所)在电源系统的工业企业是一个至关重要的因素。

外文文献翻译(含：英文原文及中文译文)文献出处：Power System Protection & Control, 2021, 3(5):63-68.英文原文General Requirements to Construction of SubstationCarpentier JennySubstations are a vital element in a power supply system of industrial enterprises. They serve to receive , convert and distribute electric energy .Depending on power and purpose ,the substations are divided into central distribution substations for a voltage of 110-500kV;main step-down substations for110-220/6-10-35kV;deep entrance substations for 110-330/6-10kV;distribution substations for 6-10kV;shop transformer substations for 6-10/ the main step-down substations, the energy received from the power source is transformed from 110-220kV usually to 6-10kV(sometimes 35kV) which is distributed among substations of the enterprise and is fed to high-voltage services.Central distribution substations receive energy from power systems and distribute it (without or with partial transformation) via aerial and cable lines of deep entrances at a voltage of 110-220kV over the enterprise territory .Central distribution substation differs from the main distribution substation in a higher power and in that bulk of its power is at a voltage of 110-220kV;it features simplified switching circuits at primary voltage; it is fed from the power to an individual object or region .Low-and medium-power shop substations transform energy from 6-10kVto a secondary voltage of 380/220 or 660/380.Step-up transformer substations are used at power plants for transformation of energy produced by the generators to a higher voltage which decreases losses at a long-distance transmission .Converter substations are intended to convert AC to DC (sometimes vice versa) and to convert energy of one frequency to another .Converter substations with semiconductor rectifiers are convert energy of one frequency to another .Converter substations with semiconductor rectifiers are most economic. Distribution substations for 6-10kV are fed primarily from main distribution substations (sometimes from central distribution substations).With a system of dividing substations for 110-220kV , the functions of a switch-gear are accomplished by switch-gears for 6-10kV at deep entrance substations.Depending on location of substations their switch-gear may be outdoor or indoor. The feed and output lines at 6-10kV substations are mainly of the cable type .at 35-220kV substations of the aerial type .When erecting and wiring the substations, major attention is given to reliable and economic power supply of a given production. Substations are erected by industrial methods with the use of large blocks and assemblies prepared at the site shops of electric engineering organizations and factories of electrical engineering industry .Substations are usually designed for operation without continuous attendance of the duty personnel but with the use of elementary automatic and signaling devices.When constructing the structural part of a substation .it is advisableto use light-weight industrial structures and elements (panels ,floors ,etc.) made of bent sections .These elements are pre-made outside the erection zone and are only assembled at site .This considerably cuts the terms and cost of construction.Basic circuitry concepts of substations are chosen when designing a power supply system of the enterprise .Substations feature primary voltage entrances .transformers and output cable lines or current conductors of secondary voltage .Substations are mounted from equipment and elements described below .The number of possible combinations of equipment and elements is very great .When elaborating a substation circuitry ,it is necessary to strive for maximum simplification and minimizing the number of switching devices .Such substations are more reliable and economic .Circuitry is simplified by using automatic enclosure or automatic change over to reserve facility which allows rapid and faultless redundancy of individual elements and using equipment.When designing transformer substations of industrial enterprises for all voltages, the following basic considerations are taken into account:1. Preferable employment of a single-bus system with using two-bus systems only to ensure a reliable and economic power supply;2. Wide use of unitized constructions and bustles substations;employment of automatics and telemetry ;if the substation design does not envisage the use of automatics or telemetry ,the circuitry is so arranged as to allow for adding such equipment in future without excessive investments and re-work. of simple and cheap devices-isolatingswitches ,short-circuiting switches ,load-breaking isolators ,fuses ,with due regard for their switching capacity may drastically cut the need for expensive and critical oil ,vacuum ,solenoid and air switches .Substation and switch-gear circuitries are so made that using the equipment of each production line is fed from individual transformers ,assemblies ,the lines to allow their disconnection simultaneously with mechanisms without disrupting operation of adjacent production flows.When elaborating circuitry of a substation, the most vital task is to properly choose and arrange switching devices (switches, isolators, current limiters, arresters, high-voltage fuses).The decision depends on the purpose, power and significance of the substation.Power System Substation is an important and indispensable component of the power it assumed the task of conversion and distribution of grid security and the economy play a decisive role in running is to contact the user’s power plants and intermediate links. With economic development, expanding grid capacity, reliability of operation of the power grid is getting higher and higher requirements. Development of science and technology, intelligent switches, photoelectric current and voltage transformer, a run-line state detection, training simulation Substation Operation matures, such as high-tech, as well as fiber-optic technology, computer high-speed network system in the development of real-time applications, bound to the existing substation automation technology have a profound impact, all-digital substation automation system development trend.Power system is operated by the production, transmission, distributionand consumption of a variety of power linked to the composition of electrical equipment. As a result of a large number of powers can not be stored, we must ensure that the production of electricity and energy balance. With the scientific and technological advances in the technological development of our country has reached a certain level. Intelligent switches, photoelectric current and voltage transformer, a run-line state detection, training simulation Substation Operation matures, such as high-tech, as well as fiber-optic technology, computer high-speed network system in the development of real-time applications, significantly increase the transformation degree of automation.Design of our substation cable programs tend to be simple, many of the recent domestic new 220 k V substation and 110kV voltage levels of wiring without the use of dual-bus bypass bus. The use of GIS, the priority sub-bus single wire. Terminal Substation, the line as far as possible, such as transformer unit wiring. A large number of the introduction of new technology, transformer substation rising level of electrical equipment, power distribution devices from the traditional form of moving toward oil-free, vacuum switches, SF6 switches and mechanical, electrical equipment combination of the development of small-scale integration. In recent years the world famous high-voltage electrical equipment companies have been developing, the development of the various types of 145-550 kV outdoor high-pressure and ultrahigh-pressure combination of electrical appliances, some high-voltage switchgear plant has also started production of 145 k V compact outdoor portfolio electrical appliances. Smart plug-in type outdoorswitchgear is a more complete high-pressure and ultrahigh-pressure switch system, which includes electrical first and second equipment, as well as the associated fiber optic cable, such as plug-type compound. The entire distributed substation automation system; the introduction of advanced network technology; substation and the construction area covers an area of reduced substation program to simplify wiring, switchgear, bus and steel pipes, such as the use of stents to substation layout is more simple, the abolition of the former station area and optimize the layout to make a substantial decline in an area substation.With technological advances, the traditional relay protection devices are gradually being replaced by microprocessor-based protection. Microprocessor-based protection is referred to as the protection of PC computer, a digital relay protection, is based on the programmable digital circuit technology and real-time digital signal processing technology of the Power System Protection. At present, both at home and abroad have been developed to 32-bit digital signal processor for hardware-based protection, control, measurement, and data communications integration of microprocessor-based protection control devices, and artificial intelligence technology into a number of relay protection, such as artificial neural networks, fuzzy theory to determine the realization of fault type, fault location, the direction of protection, the main equipment and other new methods of protection. By means of wavelet analysis of the theory of digital signal failure of the entire frequency band information and to achieve fault detection. These artificial intelligence technologies to improve theaccuracy of failure to provide a means of identification, but also some single-frequency signal based on the traditional method difficult to identify the problems to be resolved. At present, the microprocessor-based relay protection is along the microprocessor-based protection network, and intelligent, adaptive and protection, control, measurement, signal, data communications integration direction. The most basic request that charged barbed wire net in the city circulates is safe and stable. The core problem of charged barbed wire net safety in the city stability wants to build up to be a with the city mutually accommodative of, reasonable of charged barbed wire net structure. This text passes and programs to the charged barbed wire net with electric power and designs the technique principle of the aspect analysis. Elaborated the standard concerning electric voltage grade, power supply credibility, power supply ability and charged barbed wire net safe power supply requests etc. some problems that should notice in the charged barbed wire net safety; And have already aimed at sex's elaborating request to the concrete design principle opposite charged barbed wire net safe power supply of the 220 kV transformer substation and 110kV transformer substation.How to promise power supply credibility1) Satisfy charged barbed wire net power supply safe standard. The power supply network satisfies the request of power supply credibility. The standard that all satisfies N-l, city area center high burden density important customer in the district satisfies the standard of transformer over carry. Help a southern city net power supply credibility rate index sign programming target is %.2) Press to go together with charged barbed wire net burden to transfer ability in the city satisfies following request:① The transformer substation loses any once enter line or one set lord transformer but lower power supply ability, win press to go together with charged barbed wire net to have to transfer burden to ensure the ability of power supply. ② When a female line of transformer substation stops luck because of putting, winning to press to go together with charged barbed wire net should have the ability that transfer all burden.③ When the 10kV goes together with electric wire road any check to fix or breaks down, going together with the charged barbed wire net should have non- check of transfer to fix, non- breakdown segment ability for carrying. The non- check fixes, The non- breakdown segment carries to the power is off time only for go together with to give or get an electric shock an equipments to pour a Zia operation for time.3) Ask to satisfy a following principle while allowing the capacity of the power outage and the target of the instauration power supply while going together with charged barbed wire net breakdown to make the customer the power is off:① The customer of two back track power supplies, after losing a back track, should be unlimited to give or get an electric shock.② The customer of three back track power supplies , after losing a back track, should be unlimited to give or get an electric shock, again after losing a back track, should satisfy power supply capacity 50-70% is used an electricity.③ When all of a back track or much customer's the power of back track power supplies stopped, resume target time of power supply broke down to handle for a back track restored of ask.④ At wreath net power supply method in for open the customer in the wreath network, the lowest instauration power supply request for breaking down wreath net is to need to pass charged barbed wire net operation instauration Power supply of time, its target time need for operating of asks; it is the power supply that passes to go together with net automation restriction to resume an intact block in the lain to go together with net automation circuit.(3)Power supply ability and safety1)Of each electric voltage layer net capacity in the city net, press definitely change the electric capacity carry to compare an allocation, the all levels electric voltage net changes the electric capacity carry compare satisfy the upper limit request that current ? electric power net in the city programming design lead ? stipulates. According to 2001 national economy trade committee promulgation of electric power profession standard ? electric power system safety stability lead ? middle finger: standard is under the normal movement method of the any component(is like circuit, generator, and transformer...etc.) In the electric power system have no break down or because of break down break to open, electric power system should Can keep stable to circulate with normal power supply, other components however carry, electric voltage and frequency all are allowing inside the scope. This is usually called N. one standard.The charged barbed wire net power supply safe standard has-l standard and quasi- N one 2 standards and Ns is one 2 standards.City's going together with the power supply safety of charged barbed wire net to usually request is to adopt N one standard. It is one 2 standards to have already adopted quasi- N as well at the power supply safety especially important place one 2 standards or Ns.2) Medium press and go together with charged barbed wire net and have certain back up capacity, generally should have 50% Yu degrees, while being any component check and fixing and breaking down and stopping and carrying should pass and pour a Zia operation can keep a segment the customer continue toward the customer or non- trouble power supply, go together with each component of charged barbed wire net while transferring burden however carry, unlimited electricity. When two set lords happen that the power is off at the same time, that is used circuit should adjust above 60% burden.中文译文变电站成立的一样要求Carpentier Jenny变电站是工业企业供电系统的重要组成部份。

山东理工大学毕业设计（外文翻译材料）学院：电气与电子工程学院专业：电气工程及其自动化学生姓名：***指导教师：***State enumeration technique combined with a labeling busset approach for reliability evaluation ofsubstationconfiguration in power systems1. IntroductionSubstation reliability can be assessed using either Monte Carlo simulation or analytical methods [1–7]. There are two popular enumeration techniques for reliability evaluation of substation configuration in power systems: cut set enumeration [6–9] and network state enumeration [1,2]. There exist two essential differences between the two techniques. The first one is that in the cut set method, the minimum cut sets that lead to a network failure have to be identified before all of them are enumerated,whereas in the network state technique, network states are enumerated first and then an appropriate approach is used to identify whether each of the states is a failure one or not. The second one is that a cut set contains only failed components whereas a network state is defined by both failed and non-failed components.The network state technique has following features compared to the minimum cut set method:• Dependent failures between components can be easier to incorporate, such as one component failure causing outages of multiple components, cascading failures, etc. [1,2].• Multiple failure modes of network components can be easier to consider, such as active and passive failures of a component in a substation configuration [1,2].• Operation actions can be taken into consideration. This requires a model for multiple states of components, such as success, repair and switching states for a component in a substation configuration [1,2].• Network states could be mutually exclusive if the enumeration is properly performed. The first three features are due to the fact that the network state technique focuses on a state of whole network that can easily cover any status ofsubstation components including operational switching and cascading failure sequences. The fourth merit can result in significant simplification in calculations compared to the minimum cut set method. The total failure probability is simply a sum of probabilities of mutually exclusive network failure states in the network state technique. Identifying2. ExampleThe example is a simple substation network as shown in Fig. 4. The network includes three breakers and two transformers.Losing load at the bus load is used as the criterion of substation network failure.2.1. Considering only open circuit failuresIn order to compare the network state technique with the minimum cut set method, it has been first assumed that only open circuit failures of transformers and breakers are considered and all short circuit faults are ignored. To obtain a relatively simple analytical expression of the result, it is assumed that the open circuit failure probability of all the breakers and transformers is identical and it is U. In the computer program, different failure probability values for different components can be easily specified in the data file. Using the cut set method, four minimum cut sets are identified.They are: S1 = (T1, T2}; S2 = (B1, B2), S3 = (B1, B3, T2);S4 = {B2, B3, T1). The probability of substation network failure is calculated b y Fig. 4. A simple substation network.P f = P(S1 ∪S2 ∪S3 ∪S4) = 2U2 + 2U3 − 5U4 + 2U5 (4)As usual, the four minimum cut sets are not mutually exclusive. The calculations from the left side of the second equality sign to its right side are associated with intersections among the minimum cut sets. For this simple case, it can be expressed asfollows:P f = P(S1 ∪S2 ∪S3 ∪S4)= P(S1) + P(S2) + P(S3) + P(S4) −P(S1 ∩ S2)−P(S1 ∩ S3) −P(S1 ∩ S4) −P(S2 ∩ S3) −P(S2 ∩ S4)−P(S3 ∩ S4) + P(S1 ∩ S2 ∩ S3) + P(S1 ∩ S2 ∩ S4)+P(S1 ∩ S3 ∩ S4) + P(S2 ∩ S3 ∩ S4)−P(S1 ∩ S2 ∩ S3 ∩ S4) (5)For a relatively large network, identifying all minimum cut sets and performing calculations of the union of non-mutually exclusive cut sets require considerable computational efforts. Using the presented network state enumeration with the labeling bus set approach, 16 network states are identified as failure states that lead to loss of load. Generally, although the number of network failure states is more than the number of minimum cut sets, it is much easier and faster to identify them using the labeling bus set approach in programming. Particularly, once the network failure states are identified, the total network failure probability is just the sum of probabilities of all network failure states without any calculation associated with the union and intersections. In this example, we can have the following analytical expression of substation network failure probability:P f = 2U2(1 −U)3 + 8U3(1 −U)2 + 5U4(1 −U) + U5 (6)It is interesting to note that Eqs. (4) and (6) look so different but they lead to the same result. This can be proven by assign Ua value. For instance, by letting U= 0.015, the substation network failure probability from both the equations is identical, which is0.000456498.2.2. Considering both open circuit failures and shortcircuit faultsIt is relatively difficult for the cut set method to incorporate dependent failure events, multiple failure modes and switching actions, which are associated with short circuit faults and need to be modeled in reliability evaluation of a substation configuration.It has been assumed in this example that the breakers can clear their own short circuit faults and only the short circuit faults on the two transformers are considered. When a short circuit fault happens on either transformer, thebreakers B1 and B2 will be opened by a protection action. This results in a switching state. In this state, B1 and B2 are still healthy components. Their outages are not due to a failure and cannot be treated as components in a cut set. Then, the switches (not shown in the figure) at both sides of the failed transformer are manually opened to isolate it, and B1 and B2 are re-closed so that the load may be supplied through another transformer if the second transformer is not simultaneously down. This second state corresponds to a repairing state of the faulted transformer.3. ConclusionsThe network state enumeration technique combined with the labeling bus set approach proposed in the paper is suitable for reliability evaluation of a substation configuration or a looped distribution network that needs to model dependent failures, multiple failure modes and multiple states of components.Another advantage of the presented network state enumeration technique is that enumerated network states are mutually exclusive resulting in great simplification in calculating the total network failure probability compared to the minimum cut set method. The key in the presented technique is identification of whether a state is a failure one or not. The labeling bus set approach has been proposed for this purpose.A substation configuration is used to explain the procedure including a switching action associated with dependent outages and multiple states of network components. The presented method is easy to program and can be applied to any substation or looped distribution networks.The example of a substation network demonstrates that in the case of considering only open circuit failures, the same result is obtained using the proposed method and the minimum cut set method. The example also shows that the presented technique can handle the case of considering both open failures and short circuit faults which are associated with switching actions and protection logic.结合国家统计技术在电力系统的配置标签母线变电站集方法的可靠性评价1介绍变电站的可靠性可以使用蒙特卡洛仿真法或者分析法进行评估1-7。

变电站英文范文A substation, also known as a switching station, is a crucial component of an electrical system that plays a vital role in the transmission and distribution of electricity. 变电站是电气系统中至关重要的组成部分，起着在电力传输和分配中至关重要的作用。

Substations are responsible for converting high-voltage electricity from power plants into lower-voltage electricity that can be used by homes and businesses. 变电站负责将发电厂产生的高压电力转换为可供家庭和企业使用的低压电力。

These facilities are essential for ensuring a reliable and stable supply of electricity to consumers, as they help regulate the flow of power and protect the grid from disruptions and overloads. 这些设施对确保向用户提供可靠稳定的电力供应至关重要，因为它们有助于调节电力流动并保护电网免受干扰和过载。

In addition to their primary function of voltage transformation, substations also serve as points where power can be switched and distributed to different areas, allowing for greater flexibility inmanaging the electrical grid. 除了主要的电压转换功能外，变电站还可用作电力切换和分配到不同区域的点，从而增加了管理电网的灵活性。

变电站设计英文参考文献以下是关于变电站设计的英文参考文献列表及简介：1. "Modern Power Station Practice Vol 1: Electrical Systems and Equipment" by Central Electricity Generating Board (CEGB) - 这本书是关于电站设计的权威参考书之一，其中包含了变电站设计的细节和要求。

2. "HVDC Transmission: Power Conversion Applications in Power Systems" by K.R. Padiyar - 这本书主要涉及高压直流输电的理论和应用，而变电站通常是将交流电转换成直流电进行输电的一部分，因此这本书可以帮助设计师更好地理解变电站的工作原理。

3. "Electric Power Substations Engineering" by John D. McDonald- 这本书是变电站设计和工程的综合指南，包含了变电站的各个方面，从概述到详细设计，以及施工和运行。

4. "Transformer and Inductor Design Handbook" by Colonel Wm. T. McLyman - 压变和电感器是变电站中常见的元件，因此设计师需要了解它们的设计和制造，这本书提供了详细的指导和案例。

5. "Electric Power Distribution Handbook" by Thomas Allen Short- 这本书提供了关于配电系统的基础知识和设计方法，这对于变电站设计师来说也非常重要，因为变电站通常是配电网络的一个关键组成部分。

6. "Switchgear and Protection" by J.B Gupta - 变电站中使用的开关设备和保护系统非常关键，这本书提供了涵盖相关主题的详细信息，包括故障和过电压保护，以及开关设备的选择和维护。

变电站设计英文参考文献# Design of SubstationSubstations play a vital role in the power system infrastructure, serving as the main junction point for the transmission and distribution of electrical energy. The design of substations requires careful consideration of various factors to ensure safe and efficient power transfer. This article provides an overview of the design considerations involved in the planning and construction of a substation.## Site SelectionThe first step in substation design is to identify an appropriate location. The site must be strategically chosen, considering factors such as proximity to power sources, accessibility, land availability, and environmental impacts. Adequate land area is required to accommodate the equipment, structures, and necessary safety clearances.## Electrical System AnalysisOnce the site is finalized, an electrical system analysis is conducted to determine the voltage level, load capacity, and other electrical parameters. This analysis helps in determining the type and rating of transformers, circuit breakers, and other equipment required for the substation.## Substation LayoutThe layout of the substation depends on several factors, including the configuration of the electrical system and available land area. The layout should be designed to allow for efficient power flow, adequate spacing between equipment, and clear access for maintenance and operation. Different areas for high voltage, medium voltage, and low voltage equipment are designated within the substation.## Equipment SelectionCareful selection of equipment is crucial for a well-functioning substation. Transformers, circuit breakers, switchgear, protection relays, and control systems are some of the essential components. The equipment should be reliable, efficient, and compatible with the electrical system requirements. Factors such as load capacity, fault current ratings, and safety features are considered during equipment selection.## Safety ConsiderationsSafety is of utmost importance in substation design. Adequate safety measures should be implemented to protect personnel and equipment. Safety clearances, grounding systems, fire suppression systems, and protective barriers are some of the key considerations. Compliance with relevant codes, standards, and regulations is essential for ensuring a safe working environment.## Environmental ImpactThe environmental impact of a substation should be minimized. Measures such as proper disposal of waste materials, noise reduction, and landscaping are undertaken to mitigate the impact on the surrounding ecosystem and nearby communities. Environmental regulations and guidelines must be followed throughout the design and construction process.## Construction and CommissioningOnce the design is finalized, the construction phase begins. The construction process involves civil works, installation of equipment, wiring, and testing. The commissioning phase includes the initial energization, functional testing, and synchronization with the power grid. Proper coordination between various stakeholders, including engineers, contractors, and utility companies, is crucial for a successful construction and commissioning process.## Maintenance and UpgradesRegular maintenance and upgrades are essential for the efficient operation of a substation throughout its lifespan. Periodic inspections, equipment testing, and preventivemaintenance help ensure the reliability and safety of the substation. Upgrades may be required to accommodate future growth, technological advancements, or changes in the electrical system.In conclusion, the design of a substation involves several critical considerations, including site selection, electrical system analysis, layout design, equipment selection, safety measures, environmental impact, and construction and commissioning processes.A well-designed and properly maintained substation is vital for the reliable and uninterrupted transmission and distribution of electrical energy.。

Electrical substationA substation is a part of an electrical generation, transmission, and distribution system. Substations transform voltage from high to low, or the reverse, or perform any of several other important functions. Electric power may flow through several substations between generating plant and consumer, and its voltage may change in several steps.Substations may be owned and operated by a transmission or generation electrical utility, or may be owned by a large industrial or commercial customer. Generally substations are un-attended, relying on SCADA for remote supervision and control.A substation may include transformers to change voltage levels between high transmission voltages and lower distribution voltages, or at the interconnection of two different transmission voltages. The word substation comes from the days before the distribution system became a grid. As central generation stations became larger, smaller generating plants were converted to distribution stations, receiving their energy supply from a larger plant instead of using their own generators. The first substations were connected to only one power station, where the generators were housed, and were subsidiaries of that power station.Elements of a substationSubstations generally have switching, protection and control equipment, and transformers. In a large substation, circuit breakers are used to interrupt any short circuits or overload currents that may occur on the network. Smaller distribution stations may use recloser circuit breakers or fuses for protection of distribution circuits. Substations themselves do not usually have generators, although a power plant may have a substation nearby. Other devices such as capacitors and voltage regulators may also be located at a substation.Substations may be on the surface in fenced enclosures, underground, or located in special-purpose buildings. High-rise buildings may have several indoor substations. Indoor substations are usually found in urban areas to reduce the noise from the transformers, for reasons of appearance, or to protect switchgear from extreme climate or pollution conditions. Where a substation has a metallic fence, it must be properly grounded (UK: earthed) to protect people from high voltages that may occur during a fault in the network. Earth faults at a substation can cause a ground potential rise. Currents flowing in the Earth's surface during a fault can cause metal objects to have a significantly different voltage than the ground under a person's feet; this touch potential presents a hazard of electrocution.Transmission substationA transmission substation connects two or more transmission lines. The simplest case is where all transmission lines have the same voltage. In such cases, the substation contains high-voltage switches that allow lines to be connected or isolated for fault clearance or maintenance. A transmission station may have transformers to convert between two transmission voltages, voltage control/power factor correction devices such as capacitors, reactors or static VAr compensators and equipment such as phase shifting transformers to control power flow between two adjacent power systems.Transmission substations can range from simple to complex. A small "switching station" may be little more than a bus plus some circuit breakers. The largest transmission substations can cover a large area (several acres/hectares) with multiple voltage levels, many circuit breakers and a large amount of protection and control equipment (voltage and current transformers, relays and SCADA systems). Modern substations may be implemented using international standards such as IEC Standard 61850.Distribution substationA distribution substation transfers power from the transmission system to the distribution system of an area. It is uneconomical to directly connect electricity consumers to the main transmission network, unless they use large amounts of power, so the distribution station reduces voltage to a value suitable for local distribution.The input for a distribution substation is typically at least two transmission or subtransmission lines. Input voltage may be, for example, 115 kV, or whatever is common in the area. The output is a number of feeders. Distribution voltages are typically medium voltage, between 2.4 kV and 33 kV depending on the size of the area served and the practices of the local utility.The feeders run along streets overhead (or underground, in some cases) and power the distribution transformers at or near the customer premises. In addition to transforming voltage, distribution substations also isolate faults in either the transmission or distribution systems. Distribution substations are typically the points of voltage regulation, although on long distribution circuits (of several miles/kilometers), voltage regulation equipment may also be installed along the line. The downtown areas of large cities feature complicated distribution substations, with high-voltage switching, and switching and backup systems on the low-voltage side. More typical distribution substations have a switch, one transformer, and minimal facilities on the low-voltage side.DesignThe main issues facing a power engineer are reliability and cost. A good design attempts to strike a balance between these two, to achieve sufficient reliability without excessive cost. The design should also allow expansion of the station, when required.Selection of the location of a substation must consider many factors. Sufficient land area is required for installation of equipment with necessary clearances for electrical safety, and for access to maintain large apparatus such as transformers. Where land is costly, such as in urban areas, gas insulated switchgear may save money overall. The site must have room for expansion due to load growth or planned transmission additions. Environmental effects of the substation must be considered, such as drainage, noise and road traffic effects. A grounding (earthing) system must be designed, and ground potential rise must be calculated to protect passers-by during a short-circuit in the transmission system. The substation site must be reasonably central to the distribution area to be served.The first step in planning a substation layout is the preparation of a one-line diagram which shows in simplified form the switching and protection arrangement required, as well as the incoming supply lines and outgoing feeders or transmission lines. It is a usual practice by many electrical utilities to prepare one-line diagrams with principal elements (lines, switches, circuit breakers, transformers) arranged on the page similarly to the way the apparatus would be laid out in the actual station. In a common design, incoming lines have a disconnect switch and a circuit breaker. In some cases, the lines will not have both, with either a switch or a circuit breaker being all that is considered necessary. A disconnect switch is used to provide isolation, since it cannot interrupt load current. A circuit breaker is used as a protection device to interrupt fault currents automatically, and may be used to switch loads on and off, or to cut off a line when power is flowing in the 'wrong' direction. When a large fault current flows through the circuit breaker, this is detected through the use of current transformers. The magnitude of the current transformer outputs may be used to trip the circuit breaker resulting in a disconnection of the load supplied by the circuit break from the feeding point. This seeks to isolate the fault point from the rest of the system, and allow the rest of the system to continue operating with minimal impact. Both switches and circuit breakers may be operated locally (within the substation) or remotely from a supervisory control center.Once past the switching components, the lines of a given voltage connect to one or more buses. These are sets of bus bars, usually in multiples of three, since three-phase electrical power distribution is largely universal around the world.The arrangement of switches, circuit breakers and buses used affects the cost and reliability of the substation. For important substations a ring bus, double bus, or so-called "breaker and a half" setup can be used, so that the failure of any one circuit breaker does not interrupt power to other circuits, and so that parts of the substation may be de-energized for maintenance and repairs. Substations feeding only a single industrial load may have minimal switching provisions, especially for small installations.Once having established buses for the various voltage levels, transformers may be connected between the voltage levels. These will again have a circuit breaker, much like transmission lines, in case a transformer has a fault (commonly called a "short circuit").Along with this, a substation always has control circuitry needed to command the various breakers to open in case of the failure of some component.AutomationEarly electrical substations required manual switching or adjustment of equipment, and manual collection of data for load, energy consumption, and abnormal events. As the complexity of distribution networks grew, it became economically necessary to automate supervision and control of substations from a centrally attended point, to allow overall coordination in case of emergencies and to reduce operating costs. Early efforts to remote control substations used dedicated communication wires, often run along side power circuits. Power-line carrier, microwave radio, fiber optic cables as well as dedicated wired remote control circuits have all been applied to Supervisory Control and Data Acquisition (SCADA) for substations. The development of the microprocessor made for an exponential increase in the number of points that could be economically controlled and monitored. Today, standardized communication protocols such as DNP3, IEC 61850 and Modbus, to list a few, are used to allow multiple intelligent electronic devices to communicate with each other and supervisory control centers. Distributed automatic control at substations is one element of the so-called smart grid.变电站变电站是发电，输电，配电系统的电气部分。

变电站建设外文文献翻译(文档含中英文对照即英文原文和中文翻译)General Requirements to Construction of SubstationSubstations are a vital element in a power supply system of industrial enterprises．They serve to receive ，convert and distribute electric energy .Depending on power and purpose ,the substations are divided into central distribution substations for a voltage of 110-500kV;main step-down substations for110-220/6-10-35kV;deep entrance substations for 110-330/6-10Kv;distribution substations for 6-10Kv;shop transformer substations for 6-10/0.38-0.66kV.At the main step-down substations, the energy received from the power source is transformed from 110-220kV usually to 6-10kV(sometimes 35kV) which is distributed among substations of the enterpriseand is fed to high-voltage services.Central distribution substations receive energy from power systems and distribute it (without or with partial transformation) via aerial and cable lines of deep entrances at a voltage of 110-220kV over the enterprise territory .Central distribution substation differs from the main distribution substation in a higher power and in that bulk of its power is at a voltage of 110-220kV;it features simplified switching circuits at primary voltage; it is fed from the power to an individual object or region .Low-and medium-power shop substations transform energy from 6-10kV to a secondary voltage of 380/220 or 660/380.Step-up transformer substations are used at power plants for transformation of energy produced by the generators to a higher voltage which decreases losses at a long-distance transmission .Converter substations are intended to convert AC to DC (sometimes vice versa) and to convert energy of one frequency to another .Converter substations with semiconductor rectifiers are convert energy of one frequency to another .Converter substations with semiconductor rectifiers are most economic. Distribution substations for 6-10kV are fed primarily from main distribution substations (sometimes from central distribution substations).With a system of dividing substations for 110-220kV, the functions of a switch-gear are accomplished by switch-gears for 6-10kV at deep entrance substations.Depending on location of substations their switch-gear may be outdoor or indoor. The feed and output lines at 6-10kV substations are mainly of the cable type .at 35-220kV substations of the aerial type .When erecting and wiring thesubstations ,major attention is given to reliable and economic power supply of a given production.Substations are erected by industrial methods with the use of large blocks and assemblies prepared at the site shops of electric engineering organizations and factories of electrical engineering industry .Substations are usually designed for operation without continuous attendance of the duty personnel but with the use of elementary automatic and signaling devices.When constructing the structural part of a substation .it is advisable to use light-weight industrial structures and elements (panels ,floors ,etc.) made of bent sections .These elements are pre-made outside the erection zone and are only assembled at site .This considerably cuts the terms and cost of construction.Basic circuitry concepts of substations are chosen when designing a powersupply system of the enterprise .Substations feature primary voltage entrances .transformers and output cable lines or current conductors of secondary voltage .Substations are mounted from equipment and elements described below .The number of possible combinations of equipment and elements is very great .Whenelaborating a substation circuitry ,it is necessary to strive for maximum simplification and minimizing the number of switching devices .Such substations are more reliable and economic .Circuitry is simplified by using automatic reclosure or automatic change over to reserve facility which allows rapid and faultless redundancy of individual elements and using equipment.When designing transformer substations of industrial enterprises for all voltages ,the following basic considerations are taken into account:1. Preferable employment of a single-bus system with using two-bus systems only to ensure a reliable and economic power supply;2. Wide use of unitized constructions and busless substations;3.Substantiated employment of automatics and telemetry ;if the substation design does not envisage the use of automatics or telemetry ,the circuitry is so arranged as to allow for adding such equipment in future without excessive investments and re-work.e of simple and cheap devices-isolating switches ,short-circuiting switches ,load-breaking isolators ,fuses ,with due regard for their switching capacity may drastically cut the need for expensive and critical oil ,vacuum ,solenoid and air switches .Substation and switch-gear circuitries are so made that using the equipment of each production line is fed from individual transformers ,assemblies ,the lines to allow their disconnection simultaneously with mechanisms without disrupting operation of adjacent production flows.When elaborating circuitry of a substation, the most vital task is to properly choose and arrange switching devices(switches ,isolators ,current limiters ,arresters ,high-voltage fuses).The decision depends on the purpose ,power and significance of the substation.Many years ago, scientists had very vague ideas about electricity. Many of them thought of it as a sort of fluid that flowed through wires as water flows through pipes, but they could not understand what made it flow. Many of them felt that electricity was made up of tiny particles of some kind ,but trying to separate electricity intoindividual particles baffled them.Then, the great American scientist Millikan, in 1909,astounded the scientific world by actually weighing a single particle of electricity and calculating its electric charge. This was probably one of the most delicate weighing jobs ever done by man,for a single electric particle weighs only about half of a millionth of a pound. To make up a pound it would take more of those particles than there are drops of water in the Atlantic Ocean.They are no strangers to us, these electric particles, for we know them as electrons. When large numbers of electrons break away from their atoms and move through a wire,we describe this action by saying that electricity is flowing through the wire.Yes,the electrical fluid that early scientists talked about is nothing more than electrical flowing along a wire.But how can individual electrons be made to break away from atoms? And how can these free electrons be made to along a wire? The answer to the first question lies in the structure of the atoms themselves. Some atoms are so constructed that they lose electrons easily. An atom of copper, for example ,is continually losing an electron, regaining it(or another electron),and losing it again. A copper atom normally has 29 electrons, arranged in four different orbits about its nucleus. The inside orbit has 2 electrons. The next larger orbit has 8.The third orbit is packed with 18 electrons . And the outside orbit has only one electron.It is this outside electron that the copper atom is continually losing, for it is not very closely tied to the atom. It wanders off, is replaced by another free-roving electron, and then this second electron also wandersaway.Consequently,in a copper wire free electrons are floating around in all directions among the copper atoms.Thus, even through the copper wire looks quite motionless to your ordinary eye, there is a great deal of activity going on inside it. If the wire were carrying electricity to an electric light or to some other electrical device, the electrons would not be moving around at random. Instead, many of them would be rushing in the same direction-from one end of the wire to the other.This brings us to the second question .How can free electrons be made to move along a wire? Well ,men have found several ways to do that .One way is chemical. V olta,s voltaic pile,or battery, is a chemical device that makes electricity(or electrons)flow in wires. Another way is magnetic. Faraday and Henry discovered how magnets could be used to make electricity flow in a wire.MagnetsAlmost everyone has seen horseshoe magnets-so called because they are shaped like horseshoes. Probably you have experimented with a magnet, and noticed how it will pick up tacks and nails, or other small iron objects. Men have known about magnets for thousands of years.Several thousand years ago, according to legend, a shepherd named Magnes lived on the island of Crete, in the Mediterranean Sea .He had a shepherds crook tipped with iron. One day he found an oddly shaped black stone that stuck to this iron ter, when many other such stones were found, they were called magnets(after Magnets).These were natural magnets.In recent times men have learned how to make magnets out of iron. More important still, they have discovered how to use magnets to push electrons through wires-that is, how to make electricity flow. Before we discuss this, there arecertain characteristics of magnets that we should know about.If a piece of glass is laid on top of a horse- shoes magnet, and if iron filings are then sprink ledon the glass, the filings will arrange themselves into lines. If this same thing is trid with a bar magnet(a horseshoe magnet straightened out),the lines can be seen more easily. These experiments demonstrate what scientists call magnetic lines of force. Magnets, they explain, work through lines of force that ext- end between the two ends of the magnet. But electrons seem to have magnetic lines of force around them, too.This can be proved by sticking a wire through a piece ofcard board, sprinkling iron filings on the cardboard, and connecting a battery to the wire. The filings will tend to form rings around the wire,as a result of the magnetism of the moving electrons(or electricity).So we can see that there is arelationship between moving electrons and magnetism, Magnetism results from the movement of electrons.Of course, electrons are not really flowing in the bar magnet, but they are in motion, circling the nuclei of the iron atoms. However, in the magnet, circling thelined up in such a way that their electrons are circling in the same direction. Perhaps a good comparison might be a great number of boys whirling balls onstrings in a clockwise direction around their heads.翻译：变电站建设的一般要求变电站(所)在电源系统的工业企业是一个至关重要的因素。

英文文献Power System Substation is an important and indispensable component of the power it assumed the task of conversion and distribution of grid security and the economy play a decisive role in running is to contact the user's power plants and intermediate links. With economic development, expanding grid capacity, reliability of operation of the power grid is getting higher and higher requirements. Development of science and technology, intelligent switches, photoelectric current and voltage transformer, a run-line state detection, training simulation Substation Operation matures, such as high-tech, as well as fiber-optic technology, computer high-speed network system in the development of real-time applications, bound to the existing substation automation technology have a profound impact, all-digital substation automation system development trend.Keywords: substation automationPower system is operated by the production, transmission, distribution and consumption of a variety of power linked to the composition of electrical equipment. As a result of a large number of power can not be stored, we must ensure that the production of electricity and energy balance. With the scientific and technological advances in the technological development of our country has reached a certain level. Intelligent switches, photoelectric current and voltage transformer, a run-line state detection, training simulation Substation Operation matures, such as high-tech, as well as fiber-optic technology, computer high-speed network system in the development of real-time applications, significantly increase the transformation degree of automation.Design of our substation substation cable programs tend to be simple, many of the recent domestic new 220 k V substation and 110kV voltage levels of wiring without the use of dual-bus bypass bus. The use of GIS, the priority sub-bus single wire. Terminal Substation, the line as far as possible, such as transformer unit wiring.A large number of the introduction of new technology, transformer substation rising level of electrical equipment, power distribution devices from the traditional form of moving toward oil-free, vacuum switches, SF6 switches and mechanical, electrical equipment combination of the development of small-scale integration. In recent years the world famous high-voltage electrical equipment companies have been developing, the development of the various types of 145-550 kV outdoor high-pressure and ultrahigh-pressure combination of electrical appliances, some high-voltage switchgearplant has also started production of 145 k V compact outdoor portfolio electrical appliances. Smart plug-in type outdoor switchgear is a more complete high-pressure and ultrahigh-pressure switch system, which includes electrical first and second equipment, as well as the associated fiber optic cable, such as plug-type compound. The entire distributed substation automation system; the introduction of advanced network technology; substation and the construction area covers an area of reduced substation program to simplify wiring, switchgear, bus and steel pipes, such as the use of stents to substation layout is more simple, the abolition of the former station area and optimize the layout to make a substantial decline in an area substation.With technological advances, the traditional relay protection devices are gradually being replaced by microprocessor-based protection. Microprocessor-based protection is referred to as the protection of PC computer, a digital relay protection, is based on the programmable digital circuit technology and real-time digital signal processing technology of the Power System Protection. At present, both at home and abroad have been developed to 32-bit digital signal processor for hardware-based protection, control, measurement, and data communications integration of microprocessor-based protection control devices, and artificial intelligence technology into a number of relay protection, such as artificial neural networks, fuzzy theory to determine the realization of fault type, fault location, the direction of protection, the main equipment and other new methods of protection. By means of wavelet analysis of the theory of digital signal failure of the entire frequency band information and to achieve fault detection. These artificial intelligence technology to improve the accuracy of failure to provide a means of identification, but also some single-frequency signal based on the traditional method difficult to identify the problems to be resolved. At present, the microprocessor-based relay protection is along the microprocessor-based protection network, and intelligent, adaptive and protection, control, measurement, signal, data communications integration direction.The most basic request that charged barbed wire net in the city circulates is safe and stable.The core problem of charged barbed wire net safety in the city stability wants to build up to be a with the city mutually accommodative of, reasonable of charged barbed wire net structure.This text passes and programs to the charged barbed wire net with electric power and designs the technique principle of the aspect analysis.Elaborated the standard concerning electric voltage grade, power supply credibility, power supply ability and charged barbed wire net safe power supplyrequests etc. some problems that should notice in the charged barbed wire net safety;And have already aimed at sex's elaborating request to the concrete design principle opposite charged barbed wire net safe power supply of the 220 kV transformer substation and 110kV transformer substation.How to promise power supply credibility1)Satisfy charged barbed wire net power supply safe standard.The power supply network satisfies the request of power supply credibility.The standard that all satisfies N-l, city area center high burden density important customer in the district satisfy the standard of N-2.Disallow transformer over carry.Help a southern city net power supply credibility rate index sign programming target is 99.99%.2)Press to go together with charged barbed wire net burden to transfer ability in the city satisfy following request:①The transformer substation loses any once enter line or one set lord transformer but lower power supply ability, win press to go together with charged barbed wire net to have to transfer burden to ensure the ability of power supply.②When a female line of transformer substation stops a luck because of putting, winning to press to go together with charged barbed wire net should have the ability that transfer all burden.③When the 10 kv goes together with electric wire road any check to fix or breaks down, going together with the charged barbed wire net should have non- check of transfer to fix, non- breakdown segment ability for carrying.The non- check fixs,The non- breakdown segment carries to the power is off time only for go together with to give or get an electric shock an equipments to pour a Zha operation for time.3)Ask to satisfy a following principle while allowing the capacity of the power outage and the target of the instauration power supply while going together with charged barbed wire net breakdown to make the customer the power is off:①The customer of two back track power supplies , after losing a back track, should be unlimited to give or get an electric shock.②The customer of three back track power supplies , after losing a back track, should be unlimited to give or get an electric shock, again after losing a back track, should satisfy power supply capacity 50-70% is used an electricity.③When all of a back track or much customer's the power of back track power supplies stopped, resume target time of power supply broke down to handle for a back track restored of ask.④At wreath net power supply method in for open the customer in the wreath network, the lowest instauration power supply request for breaking down wreath net is to need to pass charged barbed wire net operation instaurationPower supply of time, its target time need for operating of ask;It is the power supply that passes to go together with net automation restriction to resume an intact block in the lmin to go together with net automation circuit.Power supply ability and safety1)Of each electric voltage layer net capacity in the city net, press definitely change the electric capacity carry to compare an allocation, the all levels electric voltage net changes the electric capacity carry compare satisfy the upper limit request that current 《electric power net in the city programming design lead 》stipulates. According to 2001 national economy trade committee promulgation of electric power profession standard 《electric power system safety stability lead 》middle finger:N.a standard is under the normal movement method of the any component(is like circuit, generator, and transformer...etc.) in the electric power system have no break down or because of break down break to open, electric power system shouldCan keep stable to circulate with normal power supply, other components however carry, electric voltage and frequency all are allowing inside the scope.This is usually called N. one standard.The charged barbed wire net power supply safe standard has:N-l standard and quasi- N one 2 standards and Ns is one 2 standards.City's going together with the power supply safety of charged barbed wire net to usually request is to adopt N one one standard.It is one 2 standards to have already adopted quasi- N as well at the power supply safety specially important place one 2 standards or Ns.2)Medium press and go together with charged barbed wire net and have certain back up capacity, generally should have 50% Yu degrees, while being any component check and fixing and breaking down and stopping and carrying should pass and pour a Zha operation can keep a segment the customer continue toward the customer or non- trouble power supply, go together with each component of charged barbed wire net while transfering burden however carry, unlimited electricity.When two set lords hanpen that the power is off at the same time,that is used circuit should adjust above 60% burden.译文：变电站是电力系统中不可缺少的重要组成部分，它担负着电能转换和分配的任务，对电网的安全和经济运行起着举足轻重的作用，是联系发电厂和用户的中间环节。