H3C WA2612无线接入点设备 安装指导-APW101-正文
- 格式：pdf
- 大小：1.69 MB
- 文档页数：26
橡胶锤
十字螺丝刀
梯子
2-3
3 安装AP
本章主要包含以下内容： 3.1 安装流程 3.2 安装前检查 3.3 确定安装位置 3.4 安装AP 3.5 连接AP电源 3.6 将AP连接到网络
由于H3C WA2612 无线接入点的安装位置通常较高，AP安装好后维 护人员无法通过Console口登录设备进行维护和调试，所以建议用户 在把AP设备安装到指定位置之前，根据配置需求，可以先通过 Console口登录设备，进行远程登录（如Telnet或Web登录）的相关 配置，用户也可以直接使用设备默认的登录方式通过Telnet或Web 登录，登录设备的详细介绍请参见 登录Fat AP。
供电）电源，如想获得最大的性能，推荐使用千兆连接方式。 • 请先记录 AP 设备的 MAC 地址和序列号（MAC 地址和序列号标
识在 AP 设备背面），便于后续查找使用。
3.3 确定安装位置
确定安装位置时的原则如下： • 尽量减少 AP 和用户终端间的障碍物（如：墙壁）数量。
3-2
• 使 AP 的安装位置远离可能产生射频噪声的电子设备或装置（如： 微波炉）。
3.4.1 桌面安装
不要将 AP 摆放在任何类型的金属表面上，请选择一个无障碍物并且 能提供良好接收效果的地方放置 AP。
将 AP 设备安装到桌面的步骤如下： (1) 从设备附件中取出脚垫，然后将脚垫粘到 AP 背面的相应位置，
如下图所示：
3-3
图3-2 粘贴脚垫示意图
(2) 将 AP 脚垫朝下，平放在桌面上即可。
2: 壁挂安装架 5: 螺钉
3: 挂钉
(2) 用以太网线将 AP 设备接入到有线局域网中。 (3) 将 AP 背面的壁挂安装孔对准壁挂安装架上的挂钉位置，如下
图所示。
图3-5 AP 背面安装孔示意图
12
4
3
1: 不锈钢弹片 3: 防松脱凸包
2: 挂钉 4: 壁挂安装孔
3-6
(4) 将 AP 挂在壁挂安装架的挂钉上，如下图中①所示。 (5) 用力向下压设备，如下图中②所示，通过挂钉和不锈钢弹片将
ii
1 设备简介
H3C WA2612 无线接入点作为 Fit AP（瘦 AP）与有线无线一体化交 换机/无线控制器配合使用，所有配置任务由有线无线一体化交换机 或无线控制器完成，也可单独工作在 Fat AP 模式（胖 AP）为 WLAN （Wireless Local Area Network）用户提供无线接入服务。 H3C WA2612 无线接入点工作在 Fit AP 模式的热点应用的典型组网 如下图所示。 图1-1 Fit AP 典型组网示意图
目录
1 设备简介 ······························································································ 1-1 2 安装准备 ······························································································ 2-1
2-1
壁挂安装架
六角头螺栓、垫片和螺母
膨胀螺管和螺钉
Console cable（仅Fat AP随机附带）
脚垫
备份MAC标签
天线、电源适配器及电源线不随机发货，请用户自行选购。
2.3 安装工具
在安装设备时，可能需要用到下列的工具（以下工具需要用户自备）。
水平尺
记号笔
小刀
2-2
剥线钳
网线钳
冲击钻（1个）以及 配套钻头若干
3.4.1 桌面安装 ········································································ 3-3 3.4.2 墙面安装 ········································································ 3-4 3.4.3 吸顶安装 ········································································ 3-7 3.5 连接AP电源 ············································································ 3-10 3.5.1 上电前检查··································································· 3-10 3.5.2 本地供电 ······································································ 3-11 3.5.3 PoE供电······································································· 3-12 3.5.4 上电后检查··································································· 3-12 3.6 将AP连接到网络 ····································································· 3-12 3.6.1 查看Fit AP是否连接到网络 ·········································· 3-13 3.6.2 查看Fat AP是否连接到网络 ········································· 3-13 4 登录Fat AP ·························································································· 4-1 4.1 通过Console口登录设备 ··························································· 4-1 4.1.1 搭建配置环境 ································································· 4-2
所钻的孔与壁挂安装架上的孔成对应关系。 • 在墙面上钻好的孔中插入膨胀螺管，用橡胶锤敲打膨胀螺管一端，
直到将膨胀螺管全部敲入墙面。 • 把壁挂安装架的螺钉孔对准膨胀螺管孔，并将螺钉从相应的安装
孔穿过。 • 调整壁挂安装架的位置，并将螺钉拧紧。
3-5
图3-4 安装壁挂安装架到墙面
1 2 34 5
1: 膨胀螺管 4: 不锈钢弹片
H3C WA2612 无线接入点工作在 Fat AP 模式的热点应用的典型组网 如下图所示。
1-1
图1-2 Fat AP 典型组网示意图
设备基本配置如下表所示。 表1-1 产品基本配置列表
外形尺寸 重量
(W × D × H)
160 mm× 160 mm× 50 mm
305g
最大功 率
12.95W
材质 支持协议 塑料 802.11b/g/n
2.1 安全注意事项············································································ 2-1 2.2 设备安装附件············································································ 2-1 2.3 安装工具 ··················································································· 2-2 3 安装AP ································································································ 3-1 3.1 安装流程 ··················································································· 3-1 3.2 安装前检查 ··············································································· 3-2 3.3 确定安装位置············································································ 3-2 3.4 安装AP ····················································································· 3-3
i
4.1.2 建立超级终端连接并设置终端参数································· 4-2 4.1.3 通过Console口登录设备 ················································ 4-5 4.2 通过Telnet或者Web方式登录设备············································ 4-5
• 安装位置尽量隐蔽，不妨碍居民的日常工作和生活。 • 严禁在积水、渗水、滴漏、结露等环境下安装，并需避免线缆凝
水、渗水而造成水滴沿着线缆流入设备。
如果接口线缆有户外走线情况，请检查是否在 AP 侧加装了网口防雷 器，网口防雷器需要用户自备。
3.4 安装AP
