单片机c语言闪烁灯程序

PIC12F508单片机用按键控制LED灯C语言程序#include#include“main.h”__CONFIG(MCLRDIS&WDTDIS&UNPROTECT&INTRC);//设置配置位(MCLR 脚复位禁止,看门狗关,无代码保护，内部RC 振荡)uint count=0;ucharKey_Flag=0;void Delay_US(uchar delay){ while(delay--);}void Delay_Ms(uchar delay){ uchar i; while(delay--) { for(i=0;i<165;i++); }}void Delay_Sec(uchar delay){uchar i;for(i=0;i<delay;i++){ Delay_Ms(251); Delay_Ms(251); Delay_Ms(251); Delay_Ms(252);}}void GPIO_Port_Init(void) /*********继电器/传感器端口初始化函数**********/{TRIS = 0x1c; //继电器和LED_RED 设为输出压力流量设为输入OPTION = 0x00; //OPTION 复位值为：0xFF }void Key_Scan(void) /*********按键扫描函数**********/{Key_Flag=0; //扫描键盘之前先将按键标志清零if(Key==0){ Delay_Ms(10); //延时去抖if(Key==0) { while(!Key); //等待K1 键释放Key_Flag=1; }}}void main(){Delay_Ms(200);GPIO_Port_Init(); Delay_Sec(2);Relay_Out=1;while(1){ Key_Scan(); Red_Led=1; if(Key_Flag==1) { while(1) { Red_Led=0; Delay_Ms(200); Red_Led=1; Delay_Ms(200); } }}}#ifndef __MAIN_H__#define __MAIN_H__#define uchar unsigned char#define uint unsigned int#define Relay_Out GP0#define Red_Led GP1#define Fluid_In GP2#define Press_In GP3#define Key GP4void Delay_US(uchar delay);void Delay_Ms(uchar delay);void Delay_Sec(uint delay);void GPIO_Port_Init(void);void Key_Scan(void);#endiftips:感谢大家的阅读，本文由我司收集整编。

1例子1第二个灯亮include<reg52.h>voidmain{P1=0xfd;}include<reg52.h>SbitD1=P1^0；Voidmain{D1=0}注意：稍微改程序时需重新hex化例子2第一个灯亮include<reg52.h>//52单片机头文件sbitled1=P1^0;//单片机管脚位声明voidmain //主函数{led1=0; //将单片机P1.0口清零while1;//程序停止在这里,在后面会讲到为什么这样写;}例子3第一个灯亮include<reg52.h>//52单片机头文件voidmain //主函数{P1=0xfe;while1;//程序停止在这里,在后面会讲到为什么这样写;}2例子1第三个灯闪烁fir循环include<reg52.h>sbitD2=P1^2;unsignedinta;voidmain{D2=0;fora=0;a<=10000;a++{};D2=1;fora=0;a<=10000;a++{};}例子2第三个闪烁while循环include<reg52.h>sbitD2=P1^2;unsignedinta;voidmain{a=5000;D2=0;whilea--;a=5000;D2=1;whilea--;}2.include<reg52.h>//52单片机头文件sbitled1=P1^0;//单片机管脚位声明voidmain //主函数{unsignedinti;//定义一个int型变量while1{i=50000;//变量赋初值为50000led1=0; //点亮灯whilei--;//延时i=50000;led1=1;//熄灭灯whilei--;}}3例子1357灯同时亮include<reg52.h>//52单片机头文件sbitled1=P1^0;//单片机管脚位声明sbitled3=P1^2;//单片机管脚位声明sbitled5=P1^4;//单片机管脚位声明sbitled7=P1^6;//单片机管脚位声明voidmain //主函数{led1=0; //将单片机P1.0口清零led3=0; //将单片机P1.2口清零led5=0; //将单片机P1.4口清零led7=0; //将单片机P1.6口清零while1;//程序停止在这里,在后面会讲到为什么这样写; }例子21357同时亮include<reg52.h>//52单片机头文件voidmain //主函数{P1=0xaa;while1;//程序停止在这里,在后面会讲到为什么这样写; }例子3流水灯一个一个接着亮不循环include<reg52.h>//52单片机头文件voidmain //主函数{unsignedinti;//定义一个int型变量while1{i=50000; //变量赋初值为50000P1=0xfe; //点亮第一个灯whilei--; //延时i=50000; //变量赋初值为50000P1=0xfd; //点亮第二个灯whilei--; //延时i=50000; //变量赋初值为50000P1=0xfb; //点亮第三个灯whilei--; //延时i=50000; //变量赋初值为50000P1=0xf7; //点亮第四个灯whilei--; //延时i=50000; //变量赋初值为50000P1=0xef; //点亮第五个灯whilei--; //延时i=50000; //变量赋初值为50000P1=0xdf; //点亮第六个灯whilei--; //延时i=50000; //变量赋初值为50000P1=0xbf; //点亮第七个灯whilei--; //延时i=50000; //变量赋初值为50000P1=0x7f; //点亮第八个灯whilei--; //延时}}例子4include<reg52.h>include<intrins.h>defineuintunsignedintdefineucharunsignedcharuchartemp,num,num1;sbitbeep=P2^3;voiddelayuint;voidmaintemp=0xfe;while1{fornum1=0;num1<3;num1++{fornum=0;num<8;num++{P1=temp;beep=0;delay100;temp=_crol_temp,1;P1=0xff;beep=1;delay100;}}fornum1=0;num1<3;num1++{fornum=0;num<8;num++{P1=temp;beep=0;delay100;temp=_cror_temp,1;P1=0xff;beep=1;delay100;}}while1;}}voiddelayuintz{uintx,y;forx=z;x>0;x--fory=110;y>0;y--;}4延时子程序voiddelay{uintx;forx=100;x>0;x--{}；For的嵌套voiddelay{uintx,y; %局部变量forx=100;x>0;x-- %小括号后不加分号fory=600;y>0;y--; %小括号后的分号表示该语句是上一条语句的,分号将该句与下句隔开或者{fory=600;y>0;y--;}include<reg52.h>例子1include<reg52.h>defineuintunsignedintdefineucharunsignedcharsbitD1=P1^0;voiddelay; %注意分号不能少voidmain{while1{D1=0;delay;D1=1;delay;}}voiddelay{uintx,y;forx=100;x>0;x--fory=600;y>0;y--;}带参数的比不带参数的要方便例子2无参和有参的对比include<reg52.h>defineuintunsignedintdefineucharunsignedcharsbitD1=P1^0;//voiddelay;voiddelayuint;%带一个参数的,参数类型必须要写,参数可不写;比如可以写成uintz;也可以带多个参数voidmain{while1{D1=0;delay1200;%亮2秒D1=1;delay1200;}}/voiddelay{uintx,y;forx=100;x>0;x--fory=600;y>0;y--; }/voiddelayuintz{uintx;uchary;forx=z;x>0;x--fory=20;y>0;y--; }例子3include<reg52.h> defineuintunsignedint defineucharunsignedchar sbitD1=P1^0; voiddelayuint;voidmain{while1{D1=0;delay1200;D1=1;delay1200;}}voiddelayuintz{uintx;uchary;forx=z;x>0;x--fory=20;y>0;y--; }。

《单片机C语言程序设计实训100例—基于8051+Proteus仿真》案例第01 篇基础程序设计01 闪烁的LED/* 名称：闪烁的LED说明：LED按设定的时间间隔闪烁*/#include<reg51.h>#define uchar unsigned char#define uint unsigned intsbit LED=P1^0;//延时void DelayMS(uint x){uchar i;while(x--){for(i=0;i<120;i++);}}//主程序void main(){while(1){LED=~LED;DelayMS(150);}}02 从左到右的流水灯/* 名称：从左到右的流水灯说明：接在P0口的8个LED从左到右循环依次点亮，产生走马灯效果*/#include<reg51.h>#include<intrins.h>#define uchar unsigned char#define uint unsigned int//延时void DelayMS(uint x){uchar i;while(x--){for(i=0;i<120;i++);}}//主程序void main(){P0=0xfe;while(1){P0=_crol_(P0,1); //P0的值向左循环移动DelayMS(150);}}03 8只LED左右来回点亮/* 名称：8只LED左右来回点亮说明：程序利用循环移位函数_crol_和_cror_形成来回滚动的效果*/#include<reg51.h>#include<intrins.h>#define uchar unsigned char#define uint unsigned int//延时void DelayMS(uint x){uchar i;while(x--){for(i=0;i<120;i++);}}//主程序void main(){uchar i;P2=0x01;while(1){for(i=0;i<7;i++){P2=_crol_(P2,1); //P2的值向左循环移动DelayMS(150);}for(i=0;i<7;i++){P2=_cror_(P2,1); //P2的值向右循环移动DelayMS(150);}}}04 花样流水灯/* 名称：花样流水灯说明：16只LED分两组按预设的多种花样变换显示*/#include<reg51.h>#define uchar unsigned char#define uint unsigned intuchar code Pattern_P0[]={0xfc,0xf9,0xf3,0xe7,0xcf,0x9f,0x3f,0x7f,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xe7,0xdb,0xbd,0x7e,0xbd,0xdb,0xe7,0xff,0xe7,0xc3,0x81,0x00,0x81,0xc3,0xe7,0xff, 0xaa,0x55,0x18,0xff,0xf0,0x0f,0x00,0xff,0xf8,0xf1,0xe3,0xc7,0x8f,0x1f,0x3f,0x7f,0x7f,0x3f,0x1f,0x8f,0xc7,0xe3,0xf1,0xf8,0xff,0x00,0x00,0xff,0xff,0x0f,0xf0,0xff,0xfe,0xfd,0xfb,0xf7,0xef,0xdf,0xbf,0x7f,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0x7f,0xbf,0xdf,0xef,0xf7,0xfb,0xfd,0xfe,0xfe,0xfc,0xf8,0xf0,0xe0,0xc0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xc0,0xe0,0xf0,0xf8,0xfc,0xfe, 0x00,0xff,0x00,0xff,0x00,0xff,0x00,0xff};uchar code Pattern_P2[]={0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xfe,0xfc,0xf9,0xf3,0xe7,0xcf,0x9f,0x3f,0xff,0xe7,0xdb,0xbd,0x7e,0xbd,0xdb,0xe7,0xff,0xe7,0xc3,0x81,0x00,0x81,0xc3,0xe7,0xff, 0xaa,0x55,0x18,0xff,0xf0,0x0f,0x00,0xff,0xf8,0xf1,0xe3,0xc7,0x8f,0x1f,0x3f,0x7f,0x7f,0x3f,0x1f,0x8f,0xc7,0xe3,0xf1,0xf8,0xff,0x00,0x00,0xff,0xff,0x0f,0xf0,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xfe,0xfd,0xfb,0xf7,0xef,0xdf,0xbf,0x7f,0x7f,0xbf,0xdf,0xef,0xf7,0xfb,0xfd,0xfe,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xfe,0xfc,0xf8,0xf0,0xe0,0xc0,0x80,0x00,0x00,0x80,0xc0,0xe0,0xf0,0xf8,0xfc,0xfe,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0x00,0xff,0x00,0xff,0x00,0xff,0x00,0xff};//延时void DelayMS(uint x){uchar i;while(x--){for(i=0;i<120;i++);}}//主程序void main(){uchar i;while(1){ //从数组中读取数据送至P0和P2口显示for(i=0;i<136;i++){P0=Pattern_P0[i];P2=Pattern_P2[i];DelayMS(100);}}}05 LED模拟交通灯/* 名称：LED模拟交通灯说明：东西向绿灯亮若干秒，黄灯闪烁5次后红灯亮，红灯亮后，南北向由红灯变为绿灯，若干秒后南北向黄灯闪烁5此后变红灯，东西向变绿灯，如此重复。

delay
(500);
led=0x3c;
P1=led;
delay
(500);
led=0x18;
P1=led;
delay
(500);
led=0x00;
P1=led;
delay
(500);}{
led=0xe7;
P1=led;
delay
(500);
led=0xdb;
P1=led;
3 / 5
delay
(500);
初学单片机花样流水灯10种亮法c语言程序花样流水灯c语言程序单片机c语言单片机c语言教程单片机c语言应用100例单片机c语言入门单片机c语言轻松入门单片机c语言视频教程pic单片机c语言教程单片机c语言程序设计
sfr P1=0x90;
void delay(unsigned int);
void main(void){unsigned char led,i;
（3）void main(void){unsigned char led,i
（4）while
(1){led=0xfe
（5）i++){P1=led
（6）delay
(500)
（7）led=led<<1
（8）led=led>>1
（9）led=(led<<2)+1
内容总结
（1）sfr P1=0x90
（2）void delay(unsigned int)
(500);
led=(led>>1)+128;}{
led=0xe7;
P1=led;
delay
(500);
led=0xc3;