Linksys的WRT1200AC无线路由器内置MarVell芯片

Démarrage rapideContenu de la boîteRouteur intelligent AC1200 avec antennes externesModèle R62201. Préparez votre modem.Débranchez le cordon d'alimentation de votre modem. S'il est équipé d'une batterie de secours, retirez-la.2. Branchez votre modem.Branchez votre modem. S'il est équipé d'une batterie de secours, remettez-la en place. Ensuite, branchez le modem au port WAN jaune du routeur. 4. Connectez un appareil.Utilisez un câble Ethernet pour brancher l'ordinateur à un port de réseau local du routeur.Vous pouvez également connecter votre ordinateur ou appareil mobile WiFi au routeur à l'aide d'uneconnexion WiFi. Pour vous connecter par WiFi, utilisez le nom et le mot de passe du réseau WiFi situés sur l'étiquette du routeur.5. Connectez-vous au routeur.Ouvrez un navigateur Web.L'assistant d'installation NETGEAR s'affiche.Si vous ne voyez pas l'assistant d'installation, tapez dans la barre d'adresse du navigateur Web. Lorsque vous y êtes invité, entrez le nom d'utilisateur admin et le mot de passe password .Suivez les instructions pour établir la connexion à I nternet.6. Obtenez l'application genie.Téléchargez l'application gratuite genie à l'adresse /genie .Partager facilement du contenu multimédia, des fichiers et des imprimantes sur votre réseau à partir de votre téléphone intelligent, tablette ou ordinateur portable.3. Allumez le routeur .Le voyant d'alimentation s'allume en vert. Si le voyant d'alimentation ne s'allume pas, appuyez sur le bouton Power On/Off (marche/arrêt).Attendez que le voyant WiFis'allume en vert fixe.7. Procurez-vous le guide de l'utilisateur.Vous pouvez consulter le guide de l'utilisateur en ligne à l'adresse ou en cliquant sur le lien à cet effet dans l'interface utilisateur du produit.NETGEAR, Inc.350 East Plumeria DriveSan Jose, CA 95134, États-Unis © NETGEAR, Inc., NETGEAR et le logo NETGEARsont des marques de commerce de NETGEAR,Inc. Toutes les autres marques de commerce sontutilisées à titre de référence uniquement.Avril 2017Nom et mot de passe du réseau WiFiLe nom prédéfini du réseau (SSID) et le mot de passe (clé réseau) sont propres à votre routeur, comme un numéro de série. Comme le routeur utilise automatiquement la sécurité du WiFi, vous n'avez pas besoin de la configurer. Les paramètres WiFi figurent sur l'étiquette du routeur.Si vous modifiez les paramètres WiFi, notez-les ici pour pouvoir les consulter facilement et conservez-les dans un endroit sûr :Nom du réseau WiFi (SSID)Clé réseau (mot de passe)Connexion au réseau WiFiPour connecter votre ordinateur ou votre appareil mobile WiFi au réseau WiFi du routeur, vous pouvez utiliser la méthode manuelle ou le protocole WPS (Wi-Fi Protected Setup).Méthode manuelle1. Lancez l'utilitaire logiciel qui gère vos connexions WiFi sur l'ordinateur oul'appareil mobile que vous voulez connecter à votre routeur.Cet utilitaire recherche tous les réseaux WiFi de votre secteur.2. Recherchez et sélectionnez le nom de votre réseau WiFi (SSID).Le SSID se trouve sur l'étiquette de votre routeur.3. Entrez le mot de passe du routeur (ou votre mot de passe personnalisé, si vousl'avez changé), puis cliquez sur le bouton Connect (Connexion).Le mot de passe se trouve sur l'étiquette du routeur.4. Répétez les étapes 1 à 3 pour ajouter d'autres ordinateurs ou appareils mobiles.Méthode WPSSi votre ordinateur ou appareil mobile WiFi prend en charge la méthode WPS, vouspouvez l'utiliser pour accéder au réseau WiFi du routeur. Pour obtenir de l'aide àpropos du bouton WPS de votre ordinateur ou de votre appareil mobile, consultezles instructions ou l'aide en ligne de votre ordinateur ou de votre appareil. Il estpossible que le matériel ancien ne puisse pas utiliser la méthode WPS.Remarque : La fonction WPS ne prend pas en charge la sécurité WEP. Si vousutilisez le protocole de sécurité WEP, utilisez la méthode manuelle.1. Appuyez sur le bouton WPS du routeur.2. Dans les deux minutes, appuyez sur le bouton WPS ou cliquez sur le boutonWPS à l'écran de votre ordinateur ou de votre appareil mobile.L'ordinateur ou l'appareil mobile se connecte au réseau WiFi du routeur.3. Répétez ce processus pour ajouter d'autres ordinateurs ou appareils mobiles auréseau.Partager un appareil USB sur le réseau WiFiReadySHARE® vous permet de partager et d'accéder à un périphérique de stockageUSB branché au port USB du routeur à partir d'un ordinateur connecté au réseauWiFi de votre routeur.Accéder à un périphérique USB à partir d'unordinateur Windows1. Insérez votre périphérique USB dans le port USB du routeur.2. Sélectionnez Start > Run (Démarrer > Exécuter).3. Entrez \\readyshare dans la boîte de dialogue.4. Cliquez sur le bouton OK.Le périphérique USB s'affiche.Accéder à un périphérique USB à partir d'un ordinateur Mac1. Insérez votre périphérique USB dans le port USB du routeur.2. Sélectionnez Go > Connect to Server (Aller > Connexion au serveur).3. Entrez smb://readyshare comme adresse du serveur.4. Cliquez sur le bouton Connect (Connecter).Le périphérique USB s'affiche.SoutienNous vous remercions d'avoir acheté ce produit NETGEAR. Vous pouvez visiter le/support pour enregistrer votre produit, obtenir de l'aide, accéderaux plus récents téléchargements et guides d'utilisation, et vous joindre à notrecommunauté. Nous vous recommandons d'utiliser uniquement les ressourcesd'assistance officielles NETGEAR.Pour obtenir la déclaration de conformité actuelle pour l'UE, visitez le site/app/answers/detail/a_id/11621.Pour obtenir des renseignements sur la conformité, visitez la page/about/regulatory/.Consultez le document relatif à la conformité réglementaire avant de brancher l'appareil.。

NBR1200电信级防攻击宽带路由器产品介绍V2.0福建星网锐捷网络有限公司版权所有侵权必究目录1 产品图片 (1)2 产品概述 (2)3 产品特性 (3)4 技术参数 (7)5 典型应用 (9)6 订购信息 (10)1 产品图片图1-1NBR1200电信级防攻击宽带路由器2 产品概述RG-NBR1200是锐捷网络公司推出的电信级防攻击宽带路由器。

它主要定位于以太网/光纤/ADSL接入的普教中小学、政府、企业机构、网吧、酒店等网络环境。

RG-NBR1200采用RISC架构高性能通讯专用网络处理器。

固化带有2个百兆以太网WAN口，1个独立的光模块扩展插槽，插上模块就提供了3个WAN口，4个百兆以太网LAN口，一个Console配置口。

RG-NBR1200拥有先进的硬件架构，出色的小包转发能力。

内置高性能防火墙，具备防病毒、防攻击能力。

丰富的内网安全特性和智能的带宽管理功能。

人性化的WEB管理和监控界面。

NBR1200的最大带机数为250台。

3 产品特性高速稳定的硬件架构●采用PowerPC RISC高性能通讯专用网络处理器，内嵌锐捷网络自主研发的RGNOS网络操作平台，提供电信级产品的高性能和高稳定性。

●支持硬件端口镜像功能，不影响网络性能，兼容常见信息监控过滤系统，并且监控口在提供监控功能的同时，还可以继续使用，不会影响任何功能。

●内置电信级宽频开关电源，具有防雷、防过压、防浪涌设计，适应电压不稳定场合。

灵活的内外网应用●最多3个百兆WAN口，4个百兆LAN口，所有接口可自动识别网线和交叉线。

●支持VRRP热备份协议和基于Ping/DNS的线路检测，实现多台设备、多条宽带线路的负载均衡和线路备份。

●支持基于目的地址或源地址的负载均衡和强大精细化的策略路由。

●支持电信网通自动选路功能，实现“电信数据自动走电信线路，网通数据自动走网通线路”。

支持南方、北方选路策略，实用效果更好。

●支持采用NAT或公网模式（路由模式）上网。

全球WiFi芯片原厂及其模组厂家汇总（含具体芯片模组型号参数，超全，必收藏）主流WiFi芯片原厂1、Broadcom（博通，美国）2、Atheros（创锐讯，美国，被高通(Qualcomm)收购）3、Marvell（美满科技，美国）4、TI（德州仪器，美国）5、Ralink （雷凌，台湾，被联发科(MTK)收购）6、Realtek（瑞昱，台湾）7、上海乐鑫8、北京新岸线9、北京盛德微10、深圳南方硅谷11、上海澜起12、上海庆科（出货WiFi模组）十二大细芯片及其模组介绍如下：一、Broadcom（博通，美国）1、BCM4325标准：802.11a/b/g频段：2.4/5GHz最大传输速率：150Mbps功能：WiFi+BT2.1+FM应用：游戏设备，笔记本电脑，便携式音频/媒体/游戏设备，打印机备注：iPhone4，HTC，LG，SAMSUNG手机上都用过此芯片做的模组如下：(1)村田模组LBEH198UNBC-TEMP2、BCM4329标准：802.802.11a/b/g/n频段：2.4GHz最大传输速率：300Mbps功能：WiFi+BT2.1+FM应用：便携式音频/多媒体/游戏设备此芯片做的模组如下：▼(1)、TDK模组QRF3001应用：手机、平板、OTT盒子等。

▼(2)、海华模组AW-NH6113、BCM4330标准：802.11a/b/g/n频段：2.4/5GHz最大传输速率：150Mbps功能：WiFi+BT4.0+FM应用：智能手机，平板电脑、网络播放器等备注：iphone4S用过此芯片做的模组如下：▼(1)USI环旭模组WM-BN-BM-04(2)USI 环旭模组WM-BAN-BM-04(3)USI 环旭模组WM-BAN-BM-06▼(4)正基模组AP6493▼(5)正基模组AP63304、BCM4390标准：802.11b/g/n此芯片做的模组如下：(1)村田模组LBWB1ZZ1AD(2)村田模组LBWA1CS1AD5、BCM4334标准：802.11b/g/n频段：2.4/5GHz最大传输速率：150Mbps功能：WiFi+BT4.0+FM应用：智能手机，平板电脑备注：iphone5用过，村田331S0171模块的核心芯片此芯片做的模组如下：(1)村田模组331S0171▼(2)USI模组WM-BAN-BM-07_S▼(3)正基模组AP6234▼(4)正基模组AP64746、BCM4335标准：802.11a/b/g/n/ac频段：2.4/5GHz最大传输速率：433.3Mbps功能：WiFi+BT4.0+FM应用：智能手机，平板电脑，网络播放器等备注：三星手机i9500，note3,19508，Galaxy S4，HTC One有使用此芯片做的模组如下：▼(1)村田模组LBEH5DPXJC-589(2)USI模组WM-BAC-BM-15▼(3)正基模组AP63357、BCM4336标准：802.11b/g/n频段：2.4/5GHz功能：单WiFi此芯片做的模组如下：(1)村田模组LBWA17DZX68、BCM4339标准：802.11a/b/g/n/ac频段：2.4/5GHz功能：WiFi＋BT4.0应用：低端智能手机、平板或PC nubia Z5S使用过此芯片做的模组如下：(1)村田模组LBEH5HMZPC9、BCM4343W标准：802.11b/g/n此芯片做的模组如下：(1)村田模组LBEE5KL1DX10、BCM4383频段：2.4GHz此芯片做的模组如下：(1)正基模组AP638311、BCM40181标准：802.11 b/g/n频段：2.4GHz此芯片做的模组如下：▼(1)正基模组AP618112、BCM43340标准：802.11a/b/g/n频段：2.4/5GHz功能：WiFi＋BT4.0此芯片做的模组如下：(1)村田模组LBEH5DU1BW13、BCM43241标准：802.11a/b/g/n频段：2.4/5GHz最大传输速率：300Mbps功能：WiFi+BT4.0+FM此芯片做的模组如下：▼(1)USI模组WM-BAN-BM-1014、BCM43341标准：802.11 g/n频段：2.4/5GHz最大传输速率：150Mbps功能：WiFi+BT4.0+NFC + FM此芯片做的模组如下：(1)正基模组AP644115、BCM43362+MCU标准：802.11b/g/n频段：2.4/5GHz功能：单WiFi此芯片做的模组如下：(1)88-00153-00(2)村田模组88-00153-02(3)村田模组88-0015(4)村田模组LBWA1ZVYDZ(5)村田模组LBWB1ZZYDZ-683(6)村田模组LBWA1ZVZDZ(7)村田模组LBWB1ZZYDZ-740(8)村田模组LBWA1ZV1CD▼(9)USI模组WM-N-BM-02▼(10)USI模组WM-N-BM-09▼(11)USI模组WM-N-BM-14▼(12)正基模组AP6476(BCM43362＋BCM2076)▼(13)正基模组AP6210(WiFi BCM43362+蓝牙BCM20710)(14)正基模组AP6251(BCM 43362＋BCM4751)16、BCM43364标准：802.11b/g/n此芯片做的模组如下：(1)村田模组LBWA1KL1FX17、BCM43438标准：802.11b/g/n此芯片做的模组如下：(1)村田模组LBWA1ZZ1HD18、BCM43907标准：802.11a/b/g/n此芯片做的模组如下：(1)村田模组LBWA1UZ1GC二、Atheros（创锐讯，美国，被高通(Qualcomm)收购）1、AR1021x标准：802.11a/b/g/n频段：2.4/5GHz最大传输速率：300 Mbps此芯片做的WiFi模组如下：▼(1)科中龙WM801应用：MID，网络摄像头,机顶盒GPS,电子书,硬盘播放器,网络收音机,PSP等需要实现无线联网设备的消费类电子产品。

User GuideWRT3200ACM MU-MIMOGigabit Wi-Fi RouterContentsProduct Overview (3)Front view (3)Back view (5)Avoid Overheating (7)Wall-Mounting Placement (7)Setting Up: Basics (10)Where to find more help (10)How to install your router (10)How to Use Linksys Smart Wi-Fi (13)How to connect to Linksys Smart Wi-Fi (13)Network Map (14)Guest Access (14)Parental Controls (15)Media Prioritization (15)Speed Test (16)External Storage (16)Connectivity (17)Troubleshooting (17)Wireless (18)Security (18)Troubleshooting (19)Your router was not successfully set up (19)Your Internet cable is not plugged in message (19)Cannot access your router message (20)After setup (22)Specifications (24)Linksys WRT3200ACM (24)Environmental (24)Product Overview Front viewFront panel(1) Power indicator—(White) The icon LED is solid white while the router is powered on. It will blink when the router goes through its self-diagnostic mode during every boot-up.(2) Internet Indicator—(White/Amber) The Internet LED is solid white when connected to the Internet. It blinks white while the router works to establish a connection. A solid amber LED indicates the connection is down due to configuration issues. Amber blinking indicates that the connection is down due to hardware issues.(3) 2.4 GHz Indicator—(White) The Wireless LED is solid white when one or more clients are connected to the 2.4 GHz network. If the LED is blinking white, the router is sending or receiving data over the 2.4 GHz network.(4) 5 GHz Indicator—(White) The Wireless LED is solid white when one or more clients are connected to the 5GHz network. If the LED is blinking white, the router is sending or receiving data over the 5 GHz network.(5) eSATA Indicator—(White) When off, the USB/eSATA port is off or a USB device is connected. The LED is solid white when an eSATA device is connected. A blinking white LED indicates activity through the eSATA port.(6) USB1 Indicator—(White) When off, the USB /eSATA port is off or an eSATA device is connected. The LED is solid white when a USB device is connected. A blinking white LED indicates activity on the port.(7) USB2 Primary Indicator—(White) When off, the USB 3.0 port is off. The LED is solid white when a USB device is connected. A blinking white indicates activity on the port.(8) USB2 Secondary Indicator—(White) When off, a USB 1.0 or USB 2.0 device is connected. A solid white LED indicates a USB 3.0 device is connected.(9) ETHERNET 1 through 4 (Primary)—(White) These numbered LEDs correspond with the numbered ports on the router’s back panel. If the white LED is solid, the router is connected to a device through that port. A flashing white LED indicates network activity over that port.(10) ETHERNET 1 through 4 (Secondary)—(White) If the white LED is off, the router is successfully connected to a device through that port at 10/100 Mbps. A solid white LED indicates that the router is successfully connected to a device at 1000 Mbps.(11) WPS Indicator—(White/Amber) The LED blinks slowly for up to two minutes during Wi-Fi Protected Setup. It will be solid white for five seconds to indicate a successful connection. The LED blinks amber if the Wi-Fi Protected Setup process fails. Make sure the client device supports Wi-Fi Protected Setup. Wait until the LED is off, and then try again. The router supports one session at a time.Back view(1) Adjustable antennas—This router ships with four adjustable external antennas that should be connected to the router before powering it on. To connect the antennas, twist the antenna connector clockwise onto the antenna port on the router.Note—For best performance, position the side antennas vertically as shown in the picture on the left.(2) Wi-Fi Protected Setup™ button—Press to configure wireless security on Wi-Fi Protected Setup-enabled network devices.(3) Ethernet ports—Connect Ethernet cables to these blue gigabit (10/100/1000) ports, and to wired devices on your network.Note—For best performance, use CAT5e or higher rated cables on the Ethernet ports.(4) Internet port—Connect an Ethernet cable to this yellow gigabit (10/100/1000) port, and to a broadband Internet cable/DSL or fiber modem.Note—For best performance, use CAT5e or higher rated cables on the Internet port.(5) USB 3.0 port—Connect and share a USB drive on your network or on the Internet.(6) USB 2.0/eSATA combo port—Connect and share a USB or eSATA drive on your network or on the Internet. You can also connect a USB printer and share it across your network.(7) Reset button—Press and hold for 10 seconds (until the power LED starts flashing) to reset the router to factory settings. You can also restore the factory settings using Linksys Smart Wi-Fi on the Internet or mobile app.(8) Power port—Connect the included AC power adapter.(9) Power button (EU models only)—Press to turn on the router.Avoid OverheatingWall-Mounting PlacementThe router has wall-mount slots on the bottom of each foot for flexibility in mounting the router on the wall. The distance between the slots on the short side is 104 mm. The distance between the slots on the longer side is 210 mm. Two screws are needed to mount the router.Note—Linksys is not responsible for damages incurred by unsecured wall-mounting hardware. Mounting Instructions1.Determine where you want to mount the router and which side you should use to mount it.Make sure that the wall you use is smooth, flat, dry, and sturdy. Make sure the location is within reach of an electrical outlet.2.Before drilling holes, choose the template (short side or long side) that fits yourinstallation. Drill the holes using the correct template.3.Insert a screw into each hole and leave 4 mm of its head exposed.4.Position the router so the wall-mount slots line up with the two screws.5.Place the wall-mount slots over the screws and slide the router down until the screws fitsnugly into the wall-mount slots.Wall-Mounting TemplatePrint this page at 100% size.Place on the wall with desired router position and mark screw locations.Setting Up: BasicsWhere to find more helpIn addition to this user guide, you can find help at these locations:•/support/WRT3200ACM (documentation, downloads, FAQs, technical support, live chat, forums)•Linksys Smart Wi-Fi help (connect to Linksys Smart Wi-Fi, then click Help at the top of the screen)Note—Licenses and notices for third party software used in this product may be viewed on/en-us/license. Please contact /en-us/gplcodecenter for questions or GPL source code requests.How to install your router1.If replacing an existing router, disconnect that router first.2.Turn the antennas so they are positioned straight up and plug in your router to a powersource. European versions: press the power switch to | (on).3.Connect the Internet cable from your modem to the yellow Internet port on your router.Wait until the indicator light on your router is solid.4.Connect to the secure wireless name shown in the Quick Start Guide that came with yourrouter. (You can change the network name and password later.) If you need helpconnecting to the network refer to your device documentation on the provided CD.Note—You will not have Internet access until router setup is complete.5.Open a web browser to launch the Linksys Smart Wi-Fi Router setup instructions. If youdon’t see the instructions, type in the address bar.At the end of setup, follow the on-screen instructions to set up your Linksys Smart Wi-Fi account. Use Linksys Smart Wi-Fi to configure your router from any computer with an Internet connection. Manage your router’s settings:•Change your router’s name and password•Set up guest access•Configure parental controls•Connect devices to your network•Test your Internet connection speedNote—As part of Linksys Smart Wi-Fi account setup, you will be sent a verification e-mail. From your home network, click the link in the email to associate your router with the Linksys Smart Wi-Fi account.Tip—Print the next page, then record your router and account settings in the table as a reference. Store your notes in a safe place.2.4 GHz Network NameNetwork Password 5 GHz Network NameNetwork Password Router Password Guest Network NameGuest Network Password Linksys Smart Wi-Fi UsernameLinksys Smart Wi-Fi PasswordHow to Use Linksys Smart Wi-FiYou can configure your router from anywhere in the world by using Linksys Smart Wi-Fi, but you can also configure your router directly from your home network. Linksys Smart Wi-Fi may be available for your mobile device, as well. See your device’s app store for information.How to connect to Linksys Smart Wi-FiTo connect to Linksys Smart Wi-Fi:1.Open your computer’s web browser.2.Go to and log in to your account.If you can’t remember your password, click Forgot your password? and follow the on-screen instructions to recover it.Network MapLets you display and manage all network devices connected to your router. You can view devices on your main network and your guest network, or display information about each device.Guest AccessLets you configure and monitor a network that guests can use without accessing all of your network resources.Parental ControlsLets you block web sites and set Internet access times.Media PrioritizationLets you set which devices and applications have top priority for your network traffic.Speed TestLets you test your network’s Internet connection speed.External StorageLets you access an attached USB drive (not included) and set up file sharing, a media server, and FTP access.ConnectivityLets you configure basic and advanced network settings.TroubleshootingLets you diagnose problems with your router and check the status of the network.WirelessLets you configure your router’s wireless network. You can change the security mode, password, MAC filtering, and connect devices using Wi-Fi Protected Setup™.SecurityLets you configure your router’s wireless security. You can set up the firewall, VPN settings, and make custom settings for applications and games.TroubleshootingYou can find more help from our award-winning customer support at/support/WRT3200ACM.Your router was not successfully set upIf Linksys Smart Wi-Fi did not complete the setup, you can try the following:•Press and hold the Reset button on your router with a paperclip or pin until the LED starts blinking (about 10 seconds). Install the router again.•Temporarily disable your computer’s firewall (see the security software’s instructions for help). Install the router again.•If you have another computer, use that computer to install the router again. Your Internet cable is not plugged in messageIf you get a “Your Internet cable is not plugged in” message when trying to set up your router, follow these troubleshooting steps.•Make sure that an Ethernet or Internet cable (or a cable like the one supplied with your router) is securely connected to the yellow Internet port on the back of the router and to the appropriate port on your modem. This port on the modem is usually labeled Ethernet, but may be named Internet or WAN.•Make sure that your modem is connected to power and is turned on. If it has a power switch, make sure that it is set to the ON or l (as opposed to O) position.•If your Internet service is cable, verify that the cable modem’s CABLE port is connected to the coaxial cable provided by your ISP.•If your Internet service is DSL, make sure that the DSL phone line is connected to the modem’s DSL port.•If your computer was previously connected to your modem with a USB cable, disconnect the USB cable.•Install the router again.Cannot access your router messageTo access your router, you must be connected to your own network. If you currently have wireless Internet access, the problem may be that you have accidentally connected to a different wireless network.To fix the problem on Windows computers, do the following*:1.On your Windows desktop, click on the wireless icon in the system tray. A list of availablenetworks will appear.2.Click your own network name. Click Connect. In the example below, the computer wasconnected to another wireless network named wraith_5GHz. The wireless network name of the Linksys WRT3200ACM router, Damaged_Beez2.4 in this example, is shown selected.3.If you are prompted to enter a network key, type your password (Security Key) into theNetwork key and Confirm network key fields. Click Connect.4.Your computer connects to the network, and you should now be able to access the router. *Depending on your version of Windows, there could be some differences in wording or icons in these steps.To fix the problem on Mac computers, do the following:1.In the menu bar across the top of the screen, click the Wi-Fi icon. A list of wireless networkswill appear. Linksys Smart Wi-Fi has automatically assigned your network a name.2.In the example below, the computer was connected to another wireless network namedwraith_5GHz. The wireless network name of the Linksys WRT3200ACM router,Damaged_Beez2.4 in this example, is shown selected.3.Click the wireless network name of your Linksys WRT3200ACM router(Damaged_Beez2.4 in the example).4.Type your wireless network password (Security Key) into the Password field. Click OK. After setupThe Internet appears to be unavailableIf the Internet has difficulty communicating with your router, the problem may appear as a “Cannot find [Internet address]” message in your Web browser. If you know that the Internet address is correct, and if you’ve tried several valid Internet addresses with the same result, the message could mean that there’s a problem with your ISP or modem communicating with your router.Try the following:•Make sure that the network and power cables are securely connected.•Make sure that the power outlet that your router is connected to has power.•Reboot your router.•Contact your ISP and ask about outages in your area.The most common method of troubleshooting your router is to turn it off, then back on again. Your router can then reload its custom settings, and other devices (such as the modem) will be able to rediscover the router and communicate with it. This process is called rebooting.To reboot your router using the power cord, do the following:1.Disconnect the power cord from the router and the modem.2.Wait 10 seconds, and reconnect the power cord to the modem. Make sure it has power.3.Wait until the modem’s online indicator has stopped blinking (about two minutes). Reconnectthe power cord to the router.4.Wait until the power indicator stops blinking. Wait two minutes before trying to connect tothe Internet from a computer.To reboot your router using Linksys Smart Wi-Fi, do the following:1.Log in to Linksys Smart Wi-Fi. (See “How to connect to Linksys Smart Wi-Fi” on page 13.)2.Under Router Settings, click Troubleshooting.3.Click the Diagnostics tab.4.Under Reboot, click Reboot.5.Click Yes. The router will reboot. While the router is rebooting, all connected devices willlose their Internet connection, and will automatically reconnect when the router is ready again.Linksys Smart Wi-Fi does not open in your web browserThe latest versions of Google Chrome TM, Firefox®, Safari® (for Mac® and iPad®), Microsoft Edge, and Internet Explorer® version 8 and newer work with Linksys Smart Wi-Fi.SpecificationsLinksys WRT3200ACMModel Name Linksys MU-MIMO Gigabit Wi-Fi Router Description Dual-Band AC Router with Gigabit and 2×USB Model Number WRT3200ACMSwitch Port Speed 10/100/1000 Mbps (Gigabit Ethernet)Radio Frequency 2.4 GHz and 5 GHz# of Antennas 4 external adjustable antennasPorts Power, USB 3.0, Combo USB 2.0/eSATA,Internet, Ethernet (1-4), RP-SMA (4)Buttons Reset, Wi-Fi Protected Setup, PowerFront Panel Indicators Power, Internet, 2.4 GHz, 5 GHz, eSATA, USB1,USB2, Ethernet (1-4), Wi-Fi Protected Setup, UPnP SupportedSecurity Features WPA2, RADIUSSecurity Key Bits Up to 128-bit encryptionStorage File System Support FAT, NTFS, and HFS+Browser Support Latest versions of Google Chrome TM, Firefox®,Safari® (for Mac® and iPad®), Microsoft Edge,Internet Explorer® version 8 and newer EnvironmentalDimensions 9.68” x 7.64” x 2.05” (without antennas)(246 x 194 x 52 mm)Unit Weight 31 oz. (883 g)Power 12V, 3.0ACertifications FCC, IC, CE, Wi-Fi a/g/n/ac, Windows 7, Windows8, DLNAOperating Temperature 32 to 104°F (0 to 40°C)Storage Temperature -4 to 140°F (-20 to 60°C)Operating Humidity 10% to 80% relative humidity, non-condensing Storage Humidity 5% to 90% non-condensingNotes:For regulatory, warranty, and safety information, see the CD that came with your router or go to /support/WRT3200ACM.Specifications are subject to change without notice.Maximum performance derived from IEEE Standard 802.11 specifications. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions.BELKIN, LINKSYS and many product names and logos are trademarks of the Belkin group of companies. Third-party trademarks mentioned are the property of their respective owners. Licenses and notices for third party software used in this product may be viewed here:/en-us/license. Please contact /en-us/gplcodecenter for questions or GPL source code requests.© 2016 Belkin International, Inc. and/or its affiliates. All rights reserved.LNKPG-00391 Rev. A00。