下载文档原格式
Pamphlet 107March 2004Hose AssemblyInstallation andMaintenance TipsStratoflex Products Divisionrequirementsrequirements, both operating and profile or application rangecompatibilitySize Pressure Temperature Fluid WHEN SELECTING A HOSE ASSEMBL Y ,BE CERTAIN IT MEETS:HOSE FITTINGSHOSEContinued on page 4TYPE APPROVALEach aerospace hose assembly has a specific type of approval that allows it to be installed in an aircraft.Positive verification is required for proper inspection.•T ype Certificate (TC)• Supplemental T ype Certificate (STC)•T echnical Standard Order (TSO)• Part Manufacturing Authority (PMA)• Industry Standard (AN-AS-MS-NAS)• Direct Ship Authority (DSA)• Repaired Assembly (8130-3)INSTALLATION AND CARE OF HOSE AND HOSE ASSEMBLIESGeneral:Proper Storage:Inspection:All hose assemblies whether rubber or PTFE, should always be handled with care to prevent excessive bending, twisting, and kinking.Dragging hose on ground surfaces, using them as climbing handles and severe bending to fit cramped storage areas must be avoided.Kinking of hose occurs more easily in larger sizes and in very short assemblies.Care should be exercised in handling and installing both rubber and PTFE hose assemblies.Prior to installation, hose assemblies should be capped with appropriate dust caps or plugs, properly identified (tagged) by part number, and stored in an area free from dust or other contamination.Do not use cramped or otherwise confined storage areas.If long lengths of PTFE hose are coiled for storage, a liberal coil diameter must be provided to ensure against kinking.Never coil hose so that the minimum bend radius(ii) can be exceeded.See AS1933 for more information.1.Inspect for evidence of tube restriction due to collapse, kinking,or other damage.2.Inspect for wire damage.Assemblies with excessive wire damage should be replaced.3.aerospace hose assemblies to required pressures.See applicable Drawing/Standard and InformationBulletin 1107.NEVER STEP ON, STAND ON, OR PULL HOSE.all internally externally Proof pressure testContinued on page 5Chafe Protection:Tips for Proper Installation:Chafe guards of PTFE, vinyl, polyester, or other suitable material should be used anytime there is a possibility of chafing.Chafing should be avoided by routing of the hose assembly or by clamping.1.Attach the hose to the most inaccessible end of its routing first.Finger tighten only, so the hose is free to turn during initial installation.Hose should not be twisted on final installation.2.Attach the other end of the hose in the same manner.3.Properly orient the hose along its routing and install the required line support clamps.e proper torque and remember to always lubricate! Use established installation torque values or consult ARP908 for limits.Also, the Flats From Finger Tight (F .F .F .T) method is simple to use and moreconsistent than measuring input force.Dissimilar materials or metals require different values (e.g.aluminum to stainless steel).T ypical lay lines are repeated every nine to ten inches along the length of the hose and provides the following information:• Manufacturer's Name and Manufacturer's Code.• MIL-SPEC or Industry Spec Number.• Part Number• Dash Number (or code letter) for Size.• Manufactured/Cure Date (if Rubber).To prevent misapplication,unmarked hose assemblies until positively identified."first-in, first-out"Do not Pressure test Do not Metal identification bands are often used to tag hose assemblies with the part number(s), manufacturer, size, type, date of manufacture and proof pressure tested.A log book entry is an acceptable substitute as identification in lieu of a metal ID band for repaired hose assemblies.T o minimize aging effects of hose in storage, use the principle when selecting hose assemblies and bulk hose.build rubber hose assemblies for prolonged storage.all assemblies before installation.install hose that has exceeded the established age limits (four to eight years for rubber hose) or that show aging signs (separation of plies, cracks, etc.) in aircraft.See Parker Stratoflex Information Bulletins 1050and 1107.do not use Which Hose to Use First:HOW TO MEASURE AND SPECIFY DOUBLE ELBOW FITTINGS ON A HOSE ASSEMBL Y Measuring:When installations require hose assemblies with elbow fittings on both ends, hold the assembly so the nearest fitting is pointed in the 6 o'clock position. Measure the angle between the fittings counter-clockwise.When both fittings point to 6 o'clock, this is specified as zero degrees.Specifying Position:Suffix the hose assembly part number with the number of degrees in the angle. (Example:111511E0185D180;180 degree T wist Angle).See applicable Catalog/Assembly Drawing for specific (hose) example.TROUBLESHOOTING HOSE ASSEMBLIES See ARP1658• Inspect hoses frequently.• Replace worn or damaged hoses.• Proper clamping is critical.• Consult Parker Stratoflex for current approved products.Chafed Hose• Abrasion• Improper clamping Broken Wires • Inspect external wire braid• Any broken wires is cause forremoval/scrapKinked Hose • Smooth-bore PTFE hose is prone to kinking • Restricts fluid flow• Damaged beyond repairRusted Hose • Corroded wire braids• Any corrosion makes hose assemblysuspectLeaking Hose •Wetness around fitting• Aged hose• Improper fitting attachment Heat Damaged (Brittle)Hose • Elastomeric, PTFE and Metalhose have heat limitations• Cracks during flexingTwisted Hose • Hose is not designed to be twisted.• Induces stress.• Promotes premature wear.KINK UNDER FIRESLEEVEBURN MARKAccountability -Aerospace Crimp Data Form (ACDF) "SPECIFIC"Aerospace Fabrication Procedure (AFP) '"GENERAL",Aerospace Field Attachable Data (AFAD) "SPECIFIC"Assembly Date -Audit -Ball Gage -Beam Seal -Bend Radius -Burst Pressure -CAGE Code (Stratoflex is 98441) -Catalog Part Number -Certification -Chafe Guard -Coded Part Number -Configuration -Cuff -Cure Date -Crimp Diameter-All part numbers, processes, procedures and tooling must be verifiable.(hose, fittings, tooling),[124/1124/T08151]Examples:• AFP 501 - Aerospace Fabrication Procedure (Field Attach.Hose ~ Ftgs)• AFP 502 Aerospace Fabrication Procedure (Med/High Press.Smth Bore PTFE Hose)• AFP 504 Aerospace Fabrication Procedure (Convoluted PTFE Hose)(for T ooling),Examples:• AFAD-111-XXX • AFAD-124-XXX • AFAD-193-XXX• AFAD-112-XXX • AFAD-156-XXXHose assembly fabrication date.Periodic review of hose shops and assembly fabrication procedures.Inspection method for the inside diameter of a hose assembly.Fitting connection per MIL-F-85421, a.k.a."Dynamic Beam Seal and Lip Seal".The amount of arc (bending) a hose is capable of meeting.Maximum limit a hose is designed to be mercial and Governmental Entity code.Basic hose assembly numbering nomenclature.Verification of conformity to a stated requirement.Protection applied to the external surface of a hose assembly.Serialized numbering sequence.Physical appearance of a hose assembly.Integral silicone sleeve used to slip over the end fitting sockets.Manufacture date of bulk elastomeric (rubber) hose.Precise outside diameter of a compressed fitting socket.Direct Ship Authority (DSA)Distributor Quality Program Manual -Electro-etch -End-dip -Equipment Manual -Fabrication Date -Ferrule -Field Attachable -Fire Proof –Fire Resistant –Firesleeve -Flange -Flare -Flareless Flats From Finger Tight (FFFT) -Gage Point -High Pressure -Hose Specification -Identification Tag - OEM authorized sale of spares direct to third-party customers.Stratoflex Quality Manual for distributors.Method of marking identification bands using a mild acid.Sealant used to coat/cover the ends of AS1072 (2650X) slip-over firesleeve.Illustrated parts list for equipment used to fabricate hose assemblies.The day the hose assembly was built.Ring of metal (socket) covering the fitting nipple.Screw-together fittings able to install with wrenches and mandrel.2000°F for (15) minutes.2000°F for (5) minutes.Slip-over orange silicone and fiberglassimpregnated sleeve per AS1072 and/or brown/orange integral silicone extruded directly over the wire braid.3-4 bolt-holes, flat face seal with o-ring.Female 37° degree flare end fitting per AS4395, also mates with MS33656.(a.k.a."Globeseal'', obsolete tradename)- Female fitting per AS4375, mates with MS33514, NAS1760.Method of measuring torque by counting wrench flats.Precise measuring location of the end fitting.T ypical pressures of 3,000 psi and above.The standard form used to define key characteristics of bulk hose.-The band (typically metal) nameplate for hose assembly identification.Industry Standard (AN-AS-MS-NAS) -Information Bulletin -Inside Diameter -Internal Support Coil -Jump Factor -Kevlar(Para-Aramid) -Liability -Lip Seal -Lot Code -Low Pressure -Manufacture DateMedium Pressure -MIL-SPEC (MIL-H-25579,Etc.)MIL-STD (MS8005,MIL-STD-130,Etc.)Nipple -Nut -Outside Diameter -Part Manufacturing Authority (PMA) Polytetrafluoroethylene (PTFE) -Pounds Per Square Inch (PSI) -"General" component performancespecifications.Standardized format used to explain additional topic information.Internal cross-section measurement of a hose.Internal reinforcement to enhance the crush resistance of a hose.Amount of movement a fitting travels during the crimp process.Synthetic, nonmetallic reinforcement used in the manufacture of hose.That for which one is liable.Fitting per MIL-F-85421, a.k.a.beam-seal.Serialized number for traceability assigned to each manufacturing "run" of hose.T ypical pressures of up to 500 psi.-The date a product is produced, a k.a.Cure Date.T ypical pressures of between 500-3,000 psi.Government document used to define a product.Government document used to define a product.Section of the end fitting that is inserted inside the hose.Female threaded portion of the end fitting.The outer-most cross-section dimension of a hose.- FAA authorization to mark with OEM number.Generic name of plastic compound used in the manufacture of hose.Pressure measurement used to define hose strength.®Process Specification -Repaired Assembly (8130-3Tag) -Reusable -Society of Automotive Engineers (SAE) -Sealant -Silicone Cover -Skive Socket -Spiral -Standard Drawing -Supplemental Type Certificate (STC) -Technical Standard Order - (TSO)Test/Proof Pressure -Traceability -Twist Angle -Type Certificate (TC)Wall Thickness Working Pressure -Step by Step Instructions, Example:3146X Hose,use P-104-212;3147-X Hose, use P-104-213.Method used to identify, inspect and verify aircraft hoses.T erm to describe field attachable fittings.It implies a fitting may be reused.Engineering pound used to coat/cover ends of AS1072 firesleeve, a.k.a.end-dip.Outer layer of integral firesleeved hose.- Method of removing the hose cover expose the reinforcement for fitting installation.Ring of metal (ferrule) covering the fitting nipple.Method of applying hose reinforcement during the manufacturing process.Drawing that depicts the basic design details of an assembly.FAA production certificate for an A/C modification.FAA performance specification.T ypically twice the rated working pressure of a hose assembly.Ability to account for a complete history of a part.Angular rotation of one elbow end fitting relative to the one on the opposite end.- FAA production certificate for an airframe manufacturer.-The dimension used to define the area compressed between nipple and socket.System pressure the hose assembly will operate within.toREFERENCES:1.SOCIETY OF AUTOMOTIVE ENGINEERS,INC.(SAE)400 Commonwealth Drive Warrendale, P A 15096-0001A.Aerospace Information Reports:AIR797AIR1569AIR4918B.Aerospace Recommended Practice:ARP908ARP1658C.Aerospace Standard:AS1933:A.AC No.207-N 2.SAE DOCUMENTS:3.U.S.DEP ARTMENT OF TRANSPORTATIONFEDERAL AVIATION ADMINISTRATION (FAA) DOCUMENTS Hose Characteristics and Selection ChartHandling and Installation Practice for Aerospace HoseAssemblies Industry Practices and Guidelines for the Selection of CoiledT ubes, Flexible Hoses, Swivels, and Extension Fittings for Aircraft Fluid Systems T orque Requirements, Installation and Qualification T est,Hose and T ube Fitting Visual Inspection Guide for Installed Hose Assemblies Age Controls for Hose Containing Age-SensitiveElastomeric Material General Aviation Inspection Aids Summary, 1976Inside Diameter of HoseInch / Dash Size*D =Q X 0.4081VPOUNDS and OUNCES to KILOGRAMS0 pounds to 40 pounds (by ounces)POUNDSOUNCESBASIS:100 pounds 45.359 kilogramsKILOGRAMS012345678910111213141516171819202122232425262728293031323334353637383940-0.4540.9071.3611.8142.2682.7223.1753.6294.0824.5364.9905.4435.8976.3506.8047.2577.7118.1658.6189.0729.5259.97910.4310.8911.3411.7912.2512.7013.1513.6114.0614.5114.9715.4215.8816.3316.7817.2417.6918.1401234567891011121314150.0280.4820.9361.3891.8432.2962.7503.2033.6574.1114.5645.0185.4715.9256.3796.8327.2867.7398.1938.6479.1009.55410.0110.4610.9111.3711.8212.2812.7313.1813.6414.0914.5415.0015.4515.9016.3616.8117.2617.7218.170.0570.5100.9641.4171.8712.3252.7783.2323.6854.1394.5935.0465.5005.9536.4076.8617.3147.7688.2218.6759.1299.58210.0410.4910.9411.4011.8512.3012.7613.2113.6614.1214.5715.0315.4815.9316.3916.8417.2917.7518.200.0850.5390.9921.4461.8992.3532.8073.2603.7144.1674.6215.0755.5285.9826.4356.8897.3437.7968.2508.7039.1579.61010.0610.5210.9711.4211.8812.3312.7913.2413.6914.1514.6015.0515.5115.9616.4116.8717.3217.7818.230.1130.5671.0211.4741.9282.3812.8353.2893.7424.1964.6495.1035.5576.0106.4646.9177.3717.8248.2788.7329.1859.63910.0910.5511.0011.4511.9112.3612.8113.2713.7214.1714.6315.0815.5415.9916.4416.9017.3517.8018.260.1420.5951.0491.5031.9562.4102.8633.3173.7704.2244.6785.1315.5856.0386.4926.9467.3997.8538.3068.7609.2149.66710.1210.5711.0311.4811.9412.3912.8413.3013.7514.2014.6615.1115.5616.0216.4716.9217.3817.8318.290.1700.6241.0771.5311.9842.4382.8923.3453.7994.2524.7065.1605.6136.0676.5206.9747.4287.8818.3358.7889.2429.69610.1510.6011.0611.5111.9612.4212.8713.3213.7814.2314.6915.1415.5916.0516.5016.9517.4117.8618.310.1980.6521.1061.5592.0132.4662.9203.3743.8274.2814.7345.1885.6426.0956.5497.0027.4567.9108.3638.8179.2709.72410.1810.6311.0811.5411.9912.4512.9013.3513.8114.2614.7115.1715.6216.0716.5316.9817.4317.8918.340.2270.6801.1341.5882.0412.4952.9483.4023.8564.3094.7635.2165.6706.1236.5777.0317.4847.9388.3918.8459.2999.75210.2110.6611.1111.5712.0212.4712.9313.3813.8314.2914.7415.2015.6516.1016.5617.0117.4617.9218.370.2550.7091.1621.6162.0702.5232.9773.4303.8844.3374.7915.2455.6986.1526.6057.0597.5137.9668.4208.8739.3279.78110.2310.6911.1411.5912.0512.5012.9613.4113.8614.3214.7715.2215.6816.1316.5817.0417.4917.9518.400.2830.7371.1911.6442.0982.5513.0053.4593.9124.3664.8195.2735.7276.1806.6347.0877.5417.9958.4488.9029.3559.80910.2610.7211.1711.6212.0812.5312.9813.4413.8914.3414.8015.2515.7116.1616.6117.0717.5217.9718.430.3120.7651.2191.6732.1262.5803.0333.4873.9414.3944.8485.3015.7556.2096.6627.1167.5698.0238.4778.9309.3849.83710.2910.7411.2011.6512.1112.5613.0113.4713.9214.3714.8315.2815.7316.1916.6417.0917.5518.0018.460.3400.7941.2471.7012.1552.6083.0623.5153.9694.4234.8765.3305.7836.2376.6907.1447.5988.0518.5058.9589.4129.86610.3210.7711.2311.6812.1312.5913.0413.4913.9514.4014.8615.3115.7616.2216.6717.1217.5818.0318.480.3690.8221.2761.7292.1832.6373.0903.5443.9974.4514.9045.3585.8126.2656.7197.1727.6268.0808.5338.9879.4409.89410.3510.8011.2511.7112.1612.6213.0713.5213.9814.4314.8815.3415.7916.2416.7017.1517.6118.0618.510.3970.8501.3041.7582.2112.6653.1183.5724.0264.4794.9335.3865.8406.2946.7477.2017.6548.1088.5629.0159.4699.92210.3810.8311.2811.7412.1912.6413.1013.5514.0014.4614.9115.3715.8216.2716.7317.1817.6318.0918.540.4250.8791.3321.7862.2402.6933.1473.6004.0544.5084.9615.4155.8686.3226.7767.2297.6838.1368.5909.0439.4979.95110.4010.8611.3111.7712.2212.6713.1313.5814.0314.4914.9415.3915.8516.3016.7517.2117.6618.1218.57TORQUE CONVERSIONS/METRIC CONVERSIONSTORQUE CONVERSIONSpound foot x 12 = pound inchpound foot x 1.356 = Newton meter Newton meter x 8.850 = pound inch Newton meter x .0.737 = pound foot pound inch x .083 = pound foot pound inch x 0.113 = Newton MeterRecommended torque values for aerospace are best determined by the systemmanufacturer/user.High vibration or side load installations may require "special"torque recommendation.The basic torque range, by size andmaterial combination, can be found in SAE ARP908.METRIC TO ENGLISHinches x 25.4 = millimeters (mm)inches x 2.54 = centimeters (cm)feet x .3048 = meters (m)yard x .9144 = meters (m)psi x .0689 = barpsi x.0069 = Megapascals (MPa)psi x .0703 = Kilogram force per square centimeter (Kgf/cm²)pound force x 4.448 = Newtonspound · inch x .113 = Newton · meters (N · m)pound · foot x 1.356 = Newton · meters (N · m)millimeter x .0394 = inch (in)centimeter x .3937 = inch (in)meters x 3.281 = feet (ft)meters x 1.0936 = yards (yd)bar x 14.5 = psiMegapascals x 145.0 = psiKilogram force per square centimeter x 14.22 = psi Newtons x .2248 = pounds force (lb · f)Newton · meter x 8.850 = pound · inches (lb · in)Newton · meter x .737 = pound feet (lb · ft)MILLIMETERS to FRACTIONS to DECIMALSMMFRACTIONAL DECIMALINCHES0.39690.79381.19061.58751.98442.38122.77813.17503.57193.96884.36564.76255.15945.55625.95316.3500MMFRACTIONAL DECIMALINCHES1/641/323/641/165/643/327/641/89/645/3211/643/1613/647/3215/64¼0.01560.03120.04680.06250.07810.09370.10930.12500.14060.15620.17180.18750.20310.21870.23430.2500MMFRACTIONAL DECIMALINCHESMMFRACTIONAL DECIMALINCHES6.74697.14387.54067.93758.33448.73129.12819.52509.921910.318810.715611.112511.509411.906212.303112.700017/649/3219/645/1621/6411/3223/643/825/6413/3227/647/1629/6415/3231/64½0.26560.28120.29680.31250.32810.34370.35930.37500.39060.40620.42180.43750.45310.46870.48430.500033/6417/3235/649/1637/6419/3239/645/841/6421/3243/6411/1645/6423/3247/64¾0.51560.53120.54680.56250.57810.59370.60930.62500.64060.65620.67180.68750.70310.71870.73430.750013.096913.493813.890614.287514.684415.081215.478115.875016.271916.668817.065617.462517.859418.256218.653119.050019.446919.843820.240620.237521.034421.431221.828122.225022.621923.018823.415623.812524.209424.606225.003125.400049/6425/3251/6413/1653/6427/3255/647/857/6429/3259/6415/1661/6431/3263/6410.76560.78120.79680.81250.82810.84370 .85930.87500.89060.90620.92180.93750.95310.96870.98431.0000PRESSURE CONVERSIONS1002003004005006007008009001,0002,0003,0004,0005,0006,0007,0008,0009,00010,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000100,000 200,000 300,0000.10.20.30.40.50.60.70.80.91.02.03.04.05.06.07.08.09.01020304050607080901002003000.71.42.12.83.44.14.85.56.26.913.820.727.634.541.448.355.262.168.9137.9206.8275.8344.7413.7482.6551.6620.56891,3792,0682,7580.701.412.112.813.524.224.925.636.337.0014.1021.1028.1035.2042.2049.2056.3063.3070.30140.70211.00281.30351.60421.90492.30562.60632.90703.001406.002110.002813.000.070.140.210.280.340.410.480.550.620.71.42.12.83.44.14.85.56.26.913.820.727.634.541.448.355.262.168.9137.9206.8275.868.9137.9206.8275.8344.7413.7482.6551.6620.56891,3792,0682,7583,4474,1374,8265,5166,2056,89513,79020,68427,57934,47441,36948,26355,15862,05368,948137,895206,843275,7901020304050607080901002003004005006007008009001,0002,0003,0004,0005,0006,0007,0008,0009,00010,00020,00030,00040,00014.529.043.558.072.587.0101.5116.0130.5145.0290.1435.1580.2725.2870.21,015.31,160.31,305.31,4502,9014,3515,8027,2528,70210,15311,60313,05314,50429,00843,5111234567891020304050607080901002003004005006007008009001000200030001.02.03.14.15.16.17.18.29.210.220.430.640.851.061.271.481.691.8102.0204.0306.0408.0510.0612.0714.0816.0918.01020.02040.03060.0KILO-P ASCALS (KPa)KILO-P ASCALS(KPa)MEGA-P ASCALS(MPa)MEGA-P ASCALS(MPa)KILOGRAMSPER SQ.CENTIMETERKILOGRAMSPER SQ.CENTIMETERPOUNDS PERSQUARE INCH(psi)POUNDS PERSQUARE INCH(psi)BAR(bar)BAR(bar)TO USE:Find the temperature to be converted (either Celsius or Fahrenheit) in the center column. If known temperature is Celsius, read the Fahrenheit conversion in the left column.If known temperature is Fahrenheit, read the Celsius conversion in the right column.EXAMPLE:50.0 10 -12.2 10°C = 50°F 10°F = -12.2°C °C = 5/9 (°F-32)9 x °C5°F =+ 32°F°C°F°C°F°C°F°C°F°C °F°C-94.0 -89.0 -85.0 -76.0 -67.0 -58.0 -56.2 -54.4 -52.6 -50.8 -49.0 -47.2 -45.4 -43.6 -41.8 -40.0 -38.2 -36.4 -34.6 -32.8 -31.0 -29.2 -27.4 -25.6 -23.8 -22.0 -20.2 -18.4 -16.6 -14.8 -13.0 -11.2 - 9.4 - 7.6 - 5.8 - 4.0 - 2.2 - 0.4 1.4 3.25.06.8 8.6 10.4 12.214.015.8 17.6 19.4 21.223.024.8 26.6 28.4-70-67-65-60-55-50-49-48-47-46-45-44-43-42-41-40-39-38-37-36-35-34-33-32-31-30-29-28-27-26-25-24-23-22-21-20-19-18-17-16-15-14-13-12-11-10-9-8-7-6-5-4-3-2-57-55-54-51-48-45.6-45.0-44.4-43.9-43.3-42.8-42.2-41.7-41.1-40.6-40.0-39.4-38.9-38.3-37.8-37.2-36.7-36.1-35.6-35.0-34.4-33.9-33.3-32.8-32.2-31.7-31.1-30.6-30.0-29.4-28.9-28.3-27.8-27.2-26.7-26.1-25.6-25.0-24.4-23.9-23.3-22.8-22.2-21.7-21.1-20.6-20.0-19.4-18.930.232.033.835.637.439.241.042.844.646.448.250.051.853.655.457.259.060.862.664.466.268.069.871.673.475.277.078.880.682.484.286.087.889.691.493.295.096.898.6100.4102.2104.0105.8107.6109.4111.2113.0114.8116.6118.4120.2122.0123.8125.6-112345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152-18.3-17.8-17.2-16.7-16.1-15.6-15.0-14.4-13.9-13.3-12.8-12.2-11.7-11.1-10.6-10.0-9.4-8.9-8.3-7.8-7.2-6.7-6.1-5.6-5.0-4.4-3.9-3.3-2.8-2.2-1.7-1.1-0.60.00.61.11.72.22.83.33.94.45.05.66.16.77.27.88.38.99.410.010.611.1127.4129.2131.0132.8134.6136.4138.2140.0141.8143.6145.4147.2149.0150.8152.6154.4156.2158.0159.8161.6163.4165.2167.0168.8170.6172.4174.2176.0177.8179.6181.4183.2185.0186.8188.6190.4192.2194.0195.8197.6199.4201.2203.0204.8206.6208.4210.2212.0213.8215.6217.4219.2221.0222.8535455565758596061626364656667686970717273747576777879808182838485868788899091929394959697989910010110210310410510611.712.212.813.313.914.415.015.616.116.717.217.818.318.919.420.020.621.121.722.222.823.323.924.425.025.626.126.727.227.828.328.929.430.030.631.131.732.232.833.333.934.435.035.636.136.737.237.838.338.939.440.040.641.1224.6226.4228.2230.0231.8233.6235.4237.2239.0240.8242.6244.4246.2248.0249.3251.6253.4255.2257.0258.8260.6262.4264.2266.0267.8269.6271.4273.2275.0276.8278.6280.4282.2284.0285.8287.6289.4291.2293.0294.8296.6298.4300.2302.0303.8305.6307.4309.2311.0312.8314.6316.4318.2320.010710810911011111211311411511611711811912012112212312412512612712812913013113213313413513613713813914014114214314414514614714814915015115215315415515615715815916041.742.242.843.343.944.445.045.646.146.747.247.848.348.949.450.050.651.151.752.252.853.353.954.455.055.656.156.757.257.858.358.959.460.060.661.161.762.262.863.363.964.465.065.666.166.767.267.868.368.969.470.070.671.1321.8323.6325.4327.2329.0330.8332.6334.4336.2338.0339.8341.6343.4345.2347.0348.8350.6352.4354.2356.0357.8359.6361.4363.2365.0366.8368.6370.4372.2374.0375.8377.6379.4381.2383.0384.8386.6388.4390.2392.0393.8395.6397.4399.2401.0402.8404.6406.4408.2410.0411.8413.6415.4417.216116216316416516616716816917017117217317417517617717817918018118218318418518618718818919019119219319419519619719819920020120220320420520620720820921021121221321471.772.272.873.373.974.475.075.676.176.777.277.878.378.979.480.080.681.181.782.282.883.383.984.485.085.686.186.787.287.888.388.989.490.090.691.191.792.292.893.393.994.495.095.696.196.797.297.898.398.999.4100.0100.6101.1419.0420.8422.6424.4426.2428.0429.8431.6433.4435.2437.0438.8440.6442.4444.2446.0447.8449.6451.4453.2455.0456.8458.6460.4462.2464.0465.8467.6469.4471.2473.0474.8476.6478.4480.24825005185365545725906086266446626806987167347528429321472215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250260270280290300310320330340350360370380390400450500800101.7102.2102.8103.3103.9104.4105.0105.6106.1106.7107.2107.8108.3108.9109.4110.0110.6111.1111.7112.2112.8113.3113.9114.4115.0115.6116.1116.7117.2117.8118.3118.9119.4120.0120.6121127132138143149154160166171177182188193199204232260427 TEMPERATURE CONVERSIONS。
QC/T 639-2004 汽车用橡胶密封条(1)2007-08-21 17:20:55 作者：来源：互联网文字大小：大中小简介：QC/T 639-2004（2004-10-20发布，2005-04-01实施）前言本标准代替QC/T 639-2000《客车门窗用橡胶密封条》和QC/T 640-2000《客车门窗用植绒密封条》。
本标准与QC/T 639—2000和QC/T 640-2000的 ...QC/T 639-2004（2004-10-20发布，2005-04-01实施）前言本标准代替QC/T 639-2000《客车门窗用橡胶密封条》和QC/T 640-2000《客车门窗用植绒密封条》。
本标准与QC/T 639—2000和QC/T 640-2000的主要差异如下:——将两个标准合并为一个标准，并将标准名称改为《汽车用橡胶密封条》；——增加附录A、附录B、附录C、附录D和附录E；——增加产品长度尺寸未注公差表；——胶料性能中增加“腐蚀性”、“耐水性”项目；——胶料性能中删除“撕裂性能”项目；——胶料性能中增加胶料的三个硬度范围:50±5、80±5、90±5，并相应提高了原指标；——臭氧浓度的表示方法用10-6代替ppm；——增加成品性能11个项目以及相应的试验方法标准。
本标准附录A、附录B、附录C和附录D均为规范性附录，附录正为资料性附录。
本标准山全国汽车标准化技术委员会提出。
本标准由全国汽车标准化技术委员会归口。
本标准起草单位:上海申雅密封件有限公司、北京万源金德汽车密封制品有限公司、贵州贵航股份红阳密封件公司、天津星光橡塑有限公司、重庆益丰汽车密封条有限公司、厦门百吉工业有限公司、湖北诺克汽车密封条有限公司。
本标准主要起草人:陈海燕、马俊礼、胡主庚、郝杰、邓明香、贺文兵、俞刚莉。
QC/T 639-2004汽车用橡胶密封条1 范围本标准规定了汽车用橡胶密封条的技术要求、试验方法、检验规则及标志、包装、运输和贮存。
零件手册Parts Manual542F3系列 F3 Seriers14.4. 压料分组件/Presser Bar Components序号NO.公司件号 Part NO.名称 PartName零件描述 Description数量 Number5.5. 送料分组件/Feed Mechanism Components1101S11010压脚扳手螺钉SM9/64"x40 L=11Screw SM9/64"x40 L=1112.2. 上轴挑线分组件/Main Shaft & Thread Take-up Components210128002压脚扳手螺钉垫圈Washer 1序号NO.公司件号 Part NO.名称 PartName零件描述 Description数量 Number313811029压脚扳手Hand lifter 1序号NO.公司件号 Part NO.名称 PartName零件描述 Description数量 Number4O01004O型圈Rubber ring 1110105007倒送料连杆Reverse feed connecting rod 151011000200压脚扳手凸轮分部件Hand lifter cam asm.1211426021倒送料连杆销Connecting rod pin 1110126001挑线连杆销 (厚料）Thread take-up connecting rod pin(H)16101S20001前杠杆螺纹销Screw 211326011倒送料连杆销（-7）Connecting rod pin 11. 机壳、外装分组件/Machine Frame & Miscellaneous Cover Components11326013挑线连杆销 Thread take-up connecting rod pin 1710128015螺纹销橡胶垫圈(厚) Washer(H)23101S11005螺钉 SM9/64"x40 L=6Screw SM9/64"x40 L=6611326010挑线连杆销（-7)Thread take-up connecting rod pin 181011200100抬压脚前杠杆分部件Lift front lever component 1411401015送料调节器Feed regulator 1序号NO.公司件号 Part NO.名称 PartName零件描述 Description数量 Number2101S15001上轮螺钉 SM15/64"x28 L=15Screw SM15/64"x28 L=151910112013抬压脚拉杆Knee lifter pull rod 1510403017送料调节器轴套Feed regulator bushing 1310105001挑线连杆（厚料）Thread take-up connecting rod(H)110H05003 GB/T896-1986挡圈 5Snap ring 26101S11023送料调节器轴端螺钉SM3/16"x28 L=6.5Screw SM3/16"x28 L=6.511101S11001后窗板螺钉SM3/16"×28 L=9Screw SM3/16"×28 L=9311305010挑线连杆Thread take-up connecting rod 11110112010压脚升降板Lifting plate1710126045标盘螺柱Feed regulator stud 1210122003面板调节孔螺塞Rubber plug 24H05013GB/T896-1986挡圈Snap ring 113101S20004抬压脚拉杆螺钉SM3/16"x32Hinge Screw SM3/16"x321810122016送料调节螺钉O形圈Rubber ring 1313837005商标牌Head card 1511328010垫片washer114101S20003后杠杆轴位螺钉SM15/64"x28Hinge screw SM15/64"x28191011107200标盘旋钮组件Knob component 14302893面板（喷漆）Face plate asm 1610112003针杆曲柄护板Needle bar crank protecting plate 11510112014抬压脚后杠杆Knee lifter back lever 11011107300标盘旋钮组件（-7）Knob component 1513813005左线钩Thread guide left 171013800100挑线杆分组件Thread take-up lever asm.11610112015抬压脚顶杆Knee lifter connecting rod 110101S11022送料距旋钮螺钉SM3/16"x28 L=18Screw SM3/16"x28 L=1816101S11007右线钩螺钉SM11/64"×40 L=6Screw SM11/64"×40 L=611133800200挑线杆组件（厚料、-7）Thread take-up lever asm.(H)1171011200100抬压脚前杠杆组件Knee lifter lever asm 11110126011送料曲柄销Feed rocker crank pin1710122114面板垫Face plate gasket 1810124001挑线杆滚针轴承Needle bearing 11813811027调压螺钉Press regulating screw112101S20005抬牙连杆轴位螺钉 SM9/32"x28 L=13.5hinge Screw SM9/32"x28 L=13.51810123002针杆上毡塞Rubber plug 1911310012挑线曲柄分部件Thread take-up crank 1191381102700调压螺钉组件Presser regulating screw nut asm.11310104002送料曲柄Feed rocker shaft crank 1910122013针杆上衬套孔塞Rubber plug 11011000400挑线曲柄分部件（厚料）Thread take-up crank(H)12013811028调压螺母Press regulating nut 111304010送料曲柄（-7）Feed rocker shaft crank 11010122005挑线连杆销螺孔塞Rubber plug 111310010挑线曲柄分部件（-7）Thread take-up crank 12110102003调压导杆Press regulating guide bar 114101S11016送料曲柄螺钉SM3/16"x28 L=14Screw SM3/16"x28 L=1411110122004针杆曲柄螺孔塞Rubber plug11010105002针杆连杆Needle bar connecting rod 12211427033调压簧Press regulating spring 115400093抬牙连杆Connecting rod 112101S11004挑线杆护罩螺钉SM3/16"×28 L=7Screw SM3/16"×28 L=7111101S17001挑线曲柄螺钉（左旋）Screw12313809030压杆导架Presser bar guide bracket 116101S11016送料曲柄螺钉 SM3/16"x28 L=14Screw SM3/16"x28 L=14113303923挑线杆防护罩Thread take-up lever cover 112101S15004针杆曲柄紧固螺钉 SM9/32"x28 L=16Screw SM9/32"x28 L=16124101S15007压杆导架螺钉 SM1/4"x40 L=8Screw SM1/4"x40 L=811710104004抬牙后曲柄Feed driving shaft crank 114101S11004挑线杆护罩螺钉SM3/16"×28 L=7Screw SM3/16"×28 L=7113101S11003针杆曲柄定位螺钉SM9/32"x28 L=16Screw SM9/32"x28 L=1612510122112压杆防油套Pressure bar oil cover 118400091送料连杆Rocker shaft connecting rod 11513512004三孔线勾3-hole thread guide 11410404001针杆曲柄Needle bar crank 12610103012压杆衬套Presser bar bushing,lower 1400083送料连杆（-7）Rocker shaft connecting rod 11610122005挑线连杆销螺孔塞Rubber plug111404035针杆曲柄（厚料、-7）Needle bar crank(H)12710102042压杆Presser bar11910126006送料连杆销Connecting rod pin 117114S11015割线刀螺钉SM9/64"×40 L=6Screw SM9/64"×40 L=6215101S15002送料轴挡圈螺钉SM1/4"x40 L=6Screw SM1/4"x40 L=6228101S11009活压脚螺钉 SM9/64"x40 L=10.5 Screw SM9/64"x40 L=10.5120101S16003抬牙连杆轴位螺母 SM9/32"x28 L=4Hinge Screw SM9/32"x2811811419001割线刀Knife 1161010300400上轴前轴套组件Main shaft bushing front 1291131600600压脚组件Presser foot asm 12110102037送料轴Feed rocker shaft 11920722002油塞Rubber plug 117101S15006夹线器螺钉SM15/64"x28 L=7Screw SM15/64"x28 L=711131600100压脚组件（厚）Presser foot asm(H)2211202001抬牙轴Feed driving shaft 12010122113后窗板垫Side plate gasket 11812203002主轴中轴套Main shaft bushing mid 130********挡圈 5Snap ring523101S15006夹线器螺钉Screw121303617后窗板（喷漆）Side plate119101S14001上轴中套螺钉SM1/4"x40 L=6Screw SM1/4"x40 L=6231101S20002松线顶板螺纹销Wire release plate pin 124101S15013螺钉SM15/64"x28 L=10 ScrewSM15/64"x28 L=10122101S11001后窗板螺钉SM3/16"×28 L=9Screw SM3/16"×28 L=9112010108001上轴挡圈Main shaft thrust collar 132********螺纹销橡胶垫圈(厚)Washer(H)125302933倒缝扳手（喷漆）Reverse feed lever asm123114S30001螺栓(内六角)Screw M5×25321H03002挡圈20Snap ring 2013310112012松线顶板Wire release plate asm 12610103024倒送料轴轴套Reverse feed shaft bushing back 124114S13001直驱电机螺钉M5×20Screw M5×2032211310014送料偏心轮 Feed eccentric cam 134********松线辅钉Thread release supporting pin 12710102023倒缝送料轴Reverse feed shaft 12510133203EF3-25A平缝一体机控制器(T15)Electronic control box 1400006送料偏心轮(厚料)Feed eccentric cam (H)135H05012 松线辅钉挡圈Snap ring 12810122017倒送料轴O形圈Rubber ring12610122006送料调节器孔塞Rubber plug 12310112017送料偏心轮盖板Cover plate136********松线辅钉垫片Washer plate 12910108003送料轴挡圈Feed rocker shaft snap ring 42710122007下轴工艺孔塞Rubber plug124101S11013送料偏心轮螺钉 SM1/4"x40 L=13Screw SM1/4"x40 L=1323710127003松线辅钉弹簧Spring 130101S15002送料轴挡圈螺钉SM1/4"x40 L=6Screw SM1/4"x40 L=6228101S12001底板支柱Machine head stud Electronic 425101S11005护针片螺钉 SM9/64"x40 L=5Screw SM9/64"x40 L=5238H05003挡圈 5Snap ring 23110403015轴套Bushing 129W06001双面齿垫圈Washer12610103026上轴后轴套Main shaft bushing rear 139********松线顶板复位簧Spring 132H03001 GB/T894.1-1986挡圈 15 Snap ring 1523010113041二眼线勾2-hole thread guide 12710122105上轴后套挡油油封Oil seal 1401011900100割线刀组件Knife13310108003送料轴挡圈Feed rocker shaft snap ring 131206S11002螺钉Screw128H03001GB/T894.1-1986挡圈15Snap ring 15134101S15002送料轴挡圈螺钉SM1/4"x40 L=6Screw SM1/4"x40 L=623210113004右线钩Thread guide right 12910102035上轴Main shaft 1 3.3. 针杆、竖轴、下轴部件/Needle bar,Upright Shaft & Hook Driving Shaft Components3510403015轴套Bushing 133101S11007右线钩螺钉SM11/64"×40 L=6Screw SM11/64"x40 L=613013811040手轮贴条Handwheel lable 136H03001 GB/T894.1-1986挡圈 15 Snap ring 15134101S15006螺钉SM15/64"x28 L=7Screw SM15/64"×28 L=713110133050BRC-MF4-25A平缝一体机电机Motor1序号NO.公司件号 Part NO.名称 PartName零件描述 Description数量 Number3710104007抬牙叉形曲柄Driving shaft crank 135********松线钉Tension release pin 132GB/T93-1987弹垫5Spring washer 5310804003抬牙叉形曲柄（-7）Driving shaft crank 136********挑线簧调节座O型圈Rubber ring133 114S13001直驱电机螺钉M5×20 Screw M5×203110122013针杆上衬套孔塞Rubber plug138116S11005抬牙叉形曲柄螺钉SM11/64"x40 L=13Screw SM11/64"x40 L=13137101S15005夹线紧固螺钉SM9/64"x40 L=5.5Screw SM9/64"x40 L=5.5134S05218内六角螺钉M5×22（镀镍）Screw M5×221210103009针杆上衬套 Needle bar bushing upper 139********送料牙Feed dog 138********挑线簧Thread take-up spring 135GB/T93-1987弹垫5Spring washer 51310102041针杆Needle bar 111314001送料牙（厚料）Feed dog(H)10127031挑线簧（厚料）Thread take-up spring(H)13610122012上轴孔塞Rubber plug110102021针杆（厚料）Needle bar (H)111814001送料牙（-7）Feed dog 139********挑线簧调节座Thread tension base 1410138002针杆连接柱Needle bar connecting rod 14010107001牙架Feed bar asm.14010112005夹线板Thread tension disk 25101S11005螺钉 SM9/64"x40 L=6Screw SM9/64"x40 L=6141101S11016送料曲柄螺钉SM3/16"x28 L=14Screw SM3/16"x28 L=1414110112006松线板Disk stopper 1610103010针杆下衬套Needle bar bushing lower 14210128003牙架座螺钉垫圈Washer142101s30002夹线螺钉Thread tension post 111303023针杆下衬套(厚料、-7）Needle bar bushing lower(H)143101S11025复位板螺钉SM11/64"x40 L=7Screw SM11/64"x40 L=724310127002夹线弹簧Thread tension spring A 1710113002针杆线勾Needle bar thread guide 14410126013牙架销Feed bar pin 111427050夹线弹簧（厚料）Thread tension spring A (H)111412063针杆线勾（厚料）Needle bar thread guide(H)14510101003牙架座Feed bar bed.14410112007夹线制动板Thread disk rotating stopper 1810117001机针DBx1#14（薄料）Needle 146400689牙架组件(成品)Feed bar asm.145138S16013夹线螺母Thread tension nut 110117002机针DP×5#21（厚料）Needle(H)147101S11018送料牙螺钉 SM1/8"x44 L=6Screw SM1/8"x44 L=62461381300500夹线器组件Thread tension asm.1910413001针杆下衬套线勾Lower bushing thread guide 148101S15010左销螺钉 SM15/64"x28 L=10.5Screw SM15/64"x28 L=10.511381300700夹线器组件（厚）Thread tension asm.(H)110113009针杆下轴套线钩（厚料、-7）Lower bushing thread guide(H)14910126009送料摆动板座左销Left pin 14711413011固定式缓线钩Thread guide 110101S11006支针螺钉(进口) SM1/8"x44 L=4.5Screw SM1/8"x44 L=4.515010126007短摆动板连杆销Connecting pin148401S16001螺母SM9/64"x40Nut SM9/64"x4011110109001针杆连接柱滑块Slide block151********送料短摆动板Feed short shaking plate 149104S17002针板螺钉(进口) SM11/64"x40Screw SM11/64"x40212101S11008滑块导轨螺钉SM11/64"x40 L=8 Screw SM11/64"x40 L=8 25210109004送料长摆动板Feed long shaking plate 150********定做专用针板(扩大缝纫范围)Needle plate 11310109002针杆接头滑块导轨Needle bar guide 153********短摆动板连杆销Connecting pin111315001针板（厚料）Needle plate(H)131410425004上轴伞齿轮Upper shaft bevel gear 1541010105800送料摆动板座分部件Feed shaking plate bed components 111414006针板（-7）Needle plate 11510425003竖轴上伞齿轮Upper small bevel gear asm 155********送料摆动板座右销Right pin151********推板Slide plate 11610425002竖轴下伞齿轮lower large bevel gear asm 156101S15010左销螺钉SM15/64"x28 L=10.5Screw SM15/64"x28 L=10.515210127009推板簧Slide plate spring 117101S15007齿轮螺钉SM1/4"x40 L=7 Screw SM1/4"x40 L=7 25711427011送料调节弹簧Spring 153101S11019推板簧螺钉SM3/32"x56 L=2Screw SM3/32"x56 L=221810425001下轴伞齿轮Hook drive shaft bevel gear 158H05003挡圈5Snap ring 5154W01009GB/T97.1-1985垫圈 5Washer5419101S15007齿轮螺钉SM1/4"x40 L=7 Screw SM1/4"x40 L=7 25911412081拉簧固定板Pull spring fixing plate 120101S15007齿轮螺钉SM1/4"x40 L=7 Screw SM1/4"x40 L=7 26010127011倒送料拉簧Reverse feed pull spring 121101S15007齿轮螺钉SM1/4"x40 L=7Screw SM1/4"x40 L=7 2611140402700倒送料曲柄组件Feed reverse crank asm.122101S15006一字开槽紧定螺钉SM15/64"x28 L=4.7 Screw SM15/64"x28 L=4.7 11130402800倒送料曲柄组件（-7）Feed reverse crank asm.12310403014竖轴上轴套Upright shaft bushing upper 16211321005油管Tube 12410102040竖轴Upright shaft163114S30007弹簧悬置螺钉Screw12510403013竖轴下轴套Upright shaft bushing lower 164W02015 GB/T93-1987 弹簧垫圈M4Spring washer M412610403012下轴后轴套Hook driving shaft bushing back 165114S16004螺母SM11/64"x40Nut SM11/64"x4012710108002下轴挡圈Hook driving shaft snap ring 166S01102螺钉Screw 12810122015下轴油封Thtust collar 16711329020挡圈5Snap ring 51 2910102039下轴Hook driving shaft16810126015送料距锁合销Pin 1301010301300下轴前轴套Hook driving shaft bushing front 16910127010送料距锁合簧Spring13110123009下轴限油芯Oil wick 132101S30005下轴限油螺钉set screw133********普通车国产中厚料旋梭(扩大缝纫范围)Hook asm （Hirose）110118007厚料旋梭(扩大缝纫范围)Hook asm （H ）3410118003梭心Bobbin135********梭壳Bobbin case asm.136********旋梭定位钩Finger postioner 110112032旋梭定位勾（厚料）Finger postioner(H)37101S11011牙架曲柄螺钉 SM11/64"×40 L=13Screw SM11/64"×40 L=13138101S11012下轴挡圈螺钉 SM11/64"×40 L=4.8Screw SM11/64"×40 L=4.8239101S15006下轴后套螺钉SM11/64"×40 L=7Screw SM11/64"×40 L=717. 绕线器组件/ Bobbin Bobbin Components9. 机头附件（1）/Machine Head Accessories`6. 润滑、油量检测组件/Oil Lublication 、Oil Measuring Components公司件号 Part NO.名称 PartName 零件描述 Description 数量 11211004油窗Oil sight window 10122019油窗O形圈Rubber ring 11421008上轴供油管Main shaft oil tube 101S30008油泵连接螺柱Oil pump connecting stud 11329010开口挡圈10Snap ring 1010121001下轴供油管Hook driving shaft oil tube 10112020油泵安装板Oil pump installing base W03002弹垫Spring washer101S11011压脚螺钉SM11/64＂×40 L=9.5Screw SM11/64＂×40 L=9.510103022油泵体衬套Oil pump bushing 101S30007柱塞螺钉Plunger Screw 10127013柱塞簧Plunger spring 10122018回油柱塞Plunger 10120001油泵体Oil pump 9. 机头附件(2)/Machine Head Accessories(2)序号NO.公司件号 Part NO.名称 PartName 零件描述 Description 数量 Number11011203100机头连接钩部件 Hinge component2210122060机头连接钩座Head connecting rubber cushion 2310117012机针DBx1#14（薄料）Needle 410117022机针DP×5#21（厚料）Needle 44101S30010 机头连接钩座钉 Nail 4510118003梭心 Bobbin1610111011机头支柱 Machine head rest pin 1720731047螺丝刀（大）Screw driver,large 1810131004螺丝刀（小）Screw driver,small 191011101200油箱部件 Oiler component 18.8. 油盘、膝抬压脚分组件/Oil Ceservoir ，Knee Lifter Components1040131017防尘罩Dust cover1公司件号 Part NO.名称 PartName 零件描述 Description 数量 10122022油盘座垫Oil reservoir rubber cushion 10101006油盘Oil reservoir 10111005抬压脚顶杆Knee lifter push rod 10122020油盘垫Oil Reservoir gasket 10122021O形圈Rubber ring101S11028排油孔螺钉SM5/16"×24 L=7Screw SM5/16"×24 L=710131001油盘磁铁Oil reservoir magnet 10122023油盘支架Oil reservoir rubber cushion 10112027抬压脚双向曲柄Knee lifter crank 10127016双向曲柄扭簧Knee lifter spring H05010GB/T896-1986挡圈10Snap ring 1010102011抬压脚轴Knee lifter shaft 101S15012双向曲柄限位调节螺钉M6 L=30Screw M6 L=20101S16004双向曲柄限位调节螺母 M6 L=4Nut M6 L=4101S12002双向曲柄螺钉 M6 L=26Screw M6 L=2610101008抬牙脚操纵杆节头Bearing bracket 杰克缝纫机股份有限公司杰克缝纫机全球销量遥遥领先公司地址(Address of Company）：台州市椒江区机场南路15号No.15 Rd Airport South，Jiaojiang District Taizhou City，Zhejiang，P.R.C 邮编( Zip Code )：318000国内销售部(Domestic Trade Department)：电话(TEL)：0086-0576-******** 88177789传真(FAX)：0086-0576-********国贸部(International Trade Department)：电话(TEL)：0086-0576-******** 88177774传真(FAX)：0086-0576-********服务热线：400-88768582018.12资料如有更改，恕不另行通知，以实物为准。
世界密封品牌 (1)一、德国油控集团 (1)二、奥地利优泰科（UTEC） (2)三、美国奥赛罗（OTHELLO） (2)四、美国派克汉尼汾（Parker Hannifin） (2)五、瑞典SKF (3)六、德国DTH (3)七、日本阪上sakagami（NOK） (3)八、德国HUNGER (4)九、德国Busak+Shamban宝色霞板 (5)十、瑞典特瑞堡Trelleborg (5)十一、意大利TEADIT (5)国内密封品牌 (6)一、车氏密封 (6)二、萧星密封 (7)三、复液密封 (7)世界密封品牌一、德国油控集团德国油控集团成立于1974年，主要从事液压元件的设计开发及生产制造。
油控集团凭借其先进的技术，精湛的工艺和严格的产品质量，使其产品在欧洲大陆处于领先地位。
德国密封概览公司是油控集团下属的一个独立的子公司，该公司位于德国奥格斯堡，占地1万平米是集科研、生产、仓储为一体的现代化密封件生产企业，其产品在国际处于领先地位。
二、奥地利优泰科（UTEC）优泰科(utec)是密封科技的领先者，可以提供高品质液压、气动密封产品，工程塑料元件，优质密封材料以及全套无模具密封生产技术。
最具实力的技术力量保证了优泰科在密封领域可以提供任意尺寸、任意形式、任意数量以及任意材料（聚氨酯、橡胶类、尼龙、聚甲醛、四氟乙烯等等）的优质产品。
提供高品质液压、气动密封产品，工程塑料元件，优质密封材料以及全套无模具密封生产技术。
三、美国奥赛罗（OTHELLO）美国奥赛罗（OTHELLO）集团位于美国内华达州(NEV ADA)，亚太地区总部设在香港湾仔庄土敦道。
是专业从事密封材料行业以研发、生产和销售为一体的跨国公司。
集团拥有一流的研发团队和配套的机械系统，专门自主研发生产密封行业相关产品并不断改进和完善密封材料的性能和密封技术。
主要产品有机械密封件、盘根、软填料、垫片、密封带、密封胶、碟簧、液压密封。
四、美国派克汉尼汾（Parker Hannifin）派克汉尼汾（Parker Hannifin）简称为派克或者帕克，是一家全球性的流体控制产品供应商，由六大全球性集团组成.他们是运动与控制集团、过滤集团、环境与工业控制、航天集团、流体连接件集团与密封集团,其中CIC（Climate & Industrial Controls）部门共有四家生产电磁阀等产品的工厂：Honeywell Lucifer(瑞士), Skinner, GoldRing, SCEM(意大利), 另有一家生产高品质气动膜片阀的工厂―Sinclair Collins。
© 2012 Parker Hanni n Corporation. All rights reserved.Catalog EPS 5298/USAParker Hannifin Corporation EPS DivisionCatalog EPS 5298 Replacement Parts for PackersiParker Hannifin CorporationEPS DivisionCatalog EPS 5298Replacement Parts for PackersAVAILABLE COMPOUNDSThe above chart represents the typical physical properties of thematerials used to manufacture packer rubbers, cups and seals. Parker has a complete Research and Development lab available to develop custom compounds and test packer elements out of these compounds using state of the art packer rubber test equipment. Ask your Parker Territory Sales Manager, or Parker Customer Service Representative for assistance with your special application needs. Other materials available through R&D:• HNBR • EPDM • AFLAS ®*• VITON ®***Registered trademark of Asahi Glass Company, Limited** Registered trademark of E. I. du Pont de Nemours and CompanyParker Hannifin Corporation EPS DivisionCatalog EPS 5298Replacement Parts for Packers iiiCatalog EPS 5298Replacement Parts for PackersParker Hannifin CorporationEPS DivisionParker Hannifin Corporation EPS DivisionCatalog EPS 5298Replacement Parts for Packers 1SECTION INDEXCatalog EPS 5298Replacement Parts for PackersParker Hannifin CorporationEPS DivisionParker Hannifin Corporation EPS DivisionCatalog EPS 5298 Replacement Parts for Packers3Catalog EPS 5298Replacement Parts for PackersParker Hannifin CorporationEPS DivisionParker Hannifin Corporation EPS Division 21Parker Hannifin Corporation EPS DivisionParker Hannifin Corporation EPS DivisionParker Hannifin Corporation EPS Division 39Parker Hannifin Corporation EPS Division。
