触摸开关使用说明书(图片编辑版)

1、四路火线输出2、二路干接点输出2、联网控制二、产品参数1、工作电压：AC220V±10% 50Hz2、自耗功率：约0.3W3、单路最大负载：阻性500W 感性负载100W4、工作温度：-10℃～50℃三、安装说明及注意事项1、安装前请仔细阅读产品说明，根据实际标贴对应正确接线。

2、安装前先确认电源断开，勿带电操作。

3、取下面板重新合上时，务必先断开电源。

四、操作说明1、触控方式：自锁式（触摸按键一次，维持有效输出，再次触摸按键时断开输出）；点动式（触摸按键时，输出有效，松手即断开）。

2、背光显示：上电待机状态背光微亮，触控按键有效输出时背光高亮。

联网控制开关面板指示灯说明：左上角为配对指示灯，配对操作时点亮。

右上角为信号指示灯，触摸按键操作时亮。

如下图：3、联网控制开关接线：各输出线接主控开关位，副控及总关位不用接输出。

用双绞线将主控开关A、B口与各副控开关A、B口以A→A，B→B对应相联。

如下图：4、联网开关配对操作：a.双控（二个按键控制一路灯）如网络中有二个廊灯控制一路灯。

先长按M1上廊灯按键5秒左右，当配对指示灯亮时松手，启动配对请求。

如下图：M2收到配对请求，自动点亮配对灯进入配对状态，如下图：在配对灯灭之前，触摸M2廊灯键，M2信号灯闪亮一下，表示操作有效。

等配对灯灭后自动退出程序或重启电源强制退出程序。

配对成功便能进行双控操作。

b. 多控（多个开关控制一路灯）须两两配对，比如同网络内有几个面板要控制廊灯，先在M1面板上，长按廊灯按键5秒左右，当配对指示灯亮时松开手，启动配对请求。

M2、M3面板接到配对信号后，自动点亮配对灯进入配对应答状态，如下图在配对灯灭之前触摸各接受配对面板的廊灯按键，触摸时右上角信号指示灯闪亮一次，表示操作有效。

配对灯灭后自动退出程序或重启一次电源强制退出程序，此时M1对M2和M3的配对完成。

接下来配M2对M3。

长按M2上廊灯键约5秒，配对灯亮时松手，M2向网络发出配对请求。

联动触摸开关FASK01A-A-SMT
一、按键操作说明：
1、开关键：通电后按“开关”图标时，图标全显点亮，处于待机状态，等待其他按键操作。

当再次触摸开关键时，电源关闭。

2、照明键：控制照明灯电源，触摸“照明”键时，右边LED照明图标点亮，照明灯开启，再次触摸此键，LED照明图标熄灭，照明灯关闭。

（注:照明灯独立控制）。

3、快速键：在待机状态下，触摸“快速”键，烟机转入快速运行。

再触摸此键时，回到待机状态。

电机停止运行。

4、慢速键：在待机状态下，触摸“慢速”键，烟机转入快速运行。

再触摸此键时，回到待机状态。

电机停止运行。

5、延时键:在电机运作下，触摸“延时”键时，进入延时3分钟后关机。

在延时状态下，照明灯启动时，此时照明、延时、电源同时关闭。

6、加速键:在待机状态下，触摸“加力”键，图标点亮，烟机瞬间超速运行1分种后,默认快速运行。

再触摸此键时，回到待机状态。

电机停止运行。

用了此键后需过10分钟后才能重新开机。

7、设置/校码键：在任何状态下，长按＂校码＂键3秒进入学习状态，１５秒内：
①校码：打开装有蓝牙功能的灶具，3秒后自动退出，表示校码学习成功。

②擦除：长按“校码”键2秒，按“开关”键退出，擦除完成。

8、联动键：当校码成功后，长按“联动”键3秒钟，联动生效。

若取消联动功能，再长按“联动”键２秒钟即可，灯杯指示灯熄灭，表示联动取消。

（联动时起动默认为快速工作，可以快/慢速切换）。

B3FSTactile Switch (SMT)Surface-mounting Switches Ideal for High-density Mounting•Tape packing style also available •Allows reflow soldering• 3 actuator heights for design flexibility; Projected plunger versions allow installation of B32-series keytops ■List of ModelsNote:Order in multiples of the minimum order unit. Switches are not sold individually.RoHS CompliantTypePlunger typeHeightOperating force (OF)Plunger colorBagEmbossed taping ModelQuantity per package ModelQuantity per package6 × 6 mm B3FS-1000 models3.1 mm 0.98 N {100 gf}Black B3FS-1000100B3FS-1000P 3,0001.47 N {150 gf}IvoryB3FS-1002B3FS-1002P 2.55 N {260 gf}BlueB3FS-1005B3FS-1005P 4.3 mm0.98 N {100 gf}Black B3FS-1010B3FS-1010P 1,0001.47 N {150 gf}IvoryB3FS-1012B3FS-1012P 2.55 N {260 gf}BlueB3FS-1015B3FS-1015P 7.3 mm0.98 N {100 gf}Black B3FS-1050B3FS-1050P 1.47 N {150 gf}YellowB3FS-1052B3FS-1052P(Flat type)(Flat type)(Projected type)■Ratings/Characteristics■Operating CharacteristicsRatings1 to 50 mA, 5 to 24 VDC (resistive load)Ambient operating temperature -25°C to +70°C at 60%RH max. (with no icing or condensation)Ambient operating humidity 35% to 85% (at +5 to +35°C)Contact form SPST-NOContact resistance 100 m Ω max. (initial value) (rated: 1 mA, 5 VDC)Insulation resistance 100 M Ω min. (at 100 VDC)Dielectric strength 250 VAC, 50/60 Hz for 1 min Bounce time 5 ms max.Vibration resistance Malfunction: 10 to 55 Hz, 1.5-mm double amplitude Shock resistance Destruction: 1,000 m/s 2 {approx. 100G} max. Malfunction: 100 m/s 2 {approx. 10G} max.DurabilityStandard models (0.98 N {100 gf}): 1,000,000 operations min. High-force models (1.47 N {150 gf}): 300,000 operations min. High-force models (2.55 N {260 gf}): 100,000 operations min.Weight B3FS-1000: Approx. 0.2 gB3FS-1000Item0.98 N 1.47 N 2.55 N Operating force (OF)0.98±0.29 N {100±30 gf} 1.47±0.49 N {150±50 gf}2.55±0.69 N {260±70 gf}Releasing force (RF)0.2 N {20 gf} min.0.49 N {50 gf} min.0.49 N {50 gf} min.Pretravel (PT)0.25 +0.2/−0.1 mm■Dimensions (Unit: mm)Note:The numbers used for terminals in the following graphics are indicated in the “Bottom View” diagram below. In this diagram, the Switch is rotated so that the terminals are on the right and left-hand sides, and the OMRON logo appears the right way up.Note:Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. No terminal numbers are indicated on the Switches.■Key Tops B32-series Special Key Tops are available for projected plunger models. Refer to the Datasheet of B32 for details.■PrecautionsBe sure to read the safety precautions common to all Tactile Switches for correct use.。

Pointek CLS300 Capacitance Switch (Standard Version)Application examples Introduction1 Overview2 Planning/configuring3Siemens AG Digital Industries Document order number: AG080910_CLS300Ⓟ 10/2020 Subject to changeCopyright © Siemens AG 2020.All rights reservedLegal informationWarning notice systemThis manual contains notices you have to observe in order to ensure your personal safety, as well as to preventdamage to property. The notices referring to your personal safety are highlighted in the manual by a safety alertsymbol, notices referring only to property damage have no safety alert symbol. These notices shown below aregraded according to the degree of danger.DANGERindicates that death or severe personal injury will result if proper precautions are not taken.WARNINGindicates that death or severe personal injury may result if proper precautions are not taken.CAUTIONindicates that minor personal injury can result if proper precautions are not taken.NOTICEindicates that property damage can result if proper precautions are not taken.If more than one degree of danger is present, the warning notice representing the highest degree of danger willbe used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating toproperty damage.Qualified PersonnelThe product/system described in this documentation may be operated only by personnel qualified for the specifictask in accordance with the relevant documentation, in particular its warning notices and safety instructions.Qualified personnel are those who, based on their training and experience, are capable of identifying risks andavoiding potential hazards when working with these products/systems.Proper use of Siemens productsNote the following:WARNINGSiemens products may only be used for the applications described in the catalog and in the relevant technicaldocumentation. If products and components from other manufacturers are used, these must be recommendedor approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation andmaintenance are required to ensure that the products operate safely and without any problems. The permissibleambient conditions must be complied with. The information in the relevant documentation must be observed. TrademarksAll names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publicationmay be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of LiabilityWe have reviewed the contents of this publication to ensure consistency with the hardware and softwaredescribed. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, theinformation in this publication is reviewed regularly and any necessary corrections are included in subsequenteditions.Table of contents1 Introduction (4)1.1 Objective (4)1.2 Equipment (4)1.3 Disclaimer (4)2 Overview (5)3 Planning/configuring (6)3.1 Adjusting the Setpoint (6)3.2 Pointek CLS300 Applications (6)3.3 Calibration for general applications (Failsafe low, no delay) (7)3.4 Calibration for demanding applications (Failsafe low, no delay) (7)3.5 Calibration for interface detection (Failsafe low, no delay) (7)3.6 Alarm Delay Function (8)3.7 Testing the Alarm Delay (8)3.8 Operation (8)1.1ObjectiveThe objective of this application guide is to help the user become familiar with the stepsrequired to set up and calibrate the Pointek CLS300 (Standard Version). This application guideapplies to any models manufactured after January 26, 2011.1.2Equipment1.3DisclaimerNoteWhile every effort is made to verify the following information, no warranty of accuracy orusability is expressed or implied.This application guide is an addition to the operating instructions. Please review CLS300 (Standard Version) operating instructions to ensure that the device is properly mounted. This application guide provides a basic procedure for setting the switch point for correct operation of the CLS300 (Standard Version) in either covered or uncovered states. Please note that the guide applies only to hardware manufactured after January 26, 2011 as indicated by a serial number of PBD/B127xxxx or higher. (For example, PBD/C9xxxxxx or PBD/B128xxxx.)Included in the guide are the appropriate start up procedures to quickly and effectively set up the Pointek CLS300 (Standard Version) capacitance switch for general applications, demanding applications and interface detection. It also contains instructions for adjusting the setpoint and alarm delay.For more detailed information, please consult the operating manual (A5E47827796).3.1Adjusting the SetpointBefore adjusting the setpoint or alarm delay the cover must be removed.Prior to removing the cover, please ensure that power is removed, and that the applicationand installation allow for removal of the cover. (This may not be permitted in someHazardous Areas.)Once the cover has been removed, apply power to the unit. The green power LED (L3) willglow indicating that the unit is powered and operational. If L3 is not on, please consult theSpecifications and Troubleshooting sections of the operating instructions.3.2Pointek CLS300 ApplicationsPointek CLS300 can be set up for three different applications which are described in the tablebelow. Use the calibration procedure for the application that most closely describes youroperation.Application Material Setup ConditionsGeneral •dry solids•low viscosity liquids sensor uncovered;min. 100 mm (4") free space all aroundDemanding •hygroscopic / wet solids•high viscosity and high conductivityliquids sensor immersed then uncovered; but retaining max. possible material buildupInterface detection •liquid A / liquid B•foam / liquid immerse sensor in whichever material has lowest dielectric constant3.3 Calibration for general applications (Failsafe low, no delay)3.3Calibration for general applications (Failsafe low, no delay)1.Ensure that the green power LED (L3) is on.2.Set DIP switches S1 to S5 to OFF (rocker down as shown in the diagram above).3.Turn the delay potentiometer (P1) fully counter-clockwise.4.Adjust the material level of the process so that the probe is uncovered with a minimum of100 mm (4”) free space all around.5.If the yellow sensor status LED (L1) is on, proceed to step6. If L1 is off, turn the trip pointpotentiometer (P2) counter-clockwise until it just turns on. If the yellow LED does not turnon set DIP switch S5 to ON and repeat step 5.6.Slowly turn the trip point potentiometer (P2) clockwise until the yellow sensor status LED(L1) just turns off.3.4Calibration for demanding applications (Failsafe low, no delay)1.Ensure that the green power LED (L3) is on.2.Set DIP switches S1 to S5 to OFF (rocker down as shown in the diagram above).3.Turn the delay potentiometer (P1) fully counter-clockwise.4.Adjust the material level of the process so that the sensor is immersed.5.Adjust the material level of the process so that the sensor is uncovered, but retains as muchbuildup of material as possible.6.If the yellow sensor status LED (L1) is on, proceed to step7. If L1 is off, turn the trip pointpotentiometer (P2) counter-clockwise until it just turns on. If the yellow LED does not turnon set DIP switch S5 to ON and repeat step 6.7.Slowly turn the trip point potentiometer (P2) clockwise until the yellow sensor status LED(L1) just turns off.3.5Calibration for interface detection (Failsafe low, no delay)1.Ensure that the green power LED (L3) is on.2.Set DIP switches S1 to S5 to OFF (rocker down as shown in the diagram above).3.Turn the delay potentiometer (P1) fully counter-clockwise.4.Adjust the material level of the process so that the sensor is covered by the material with thelowest relative dielectric constant.5.If the yellow sensor status LED (L1) is on, proceed to step6. If L1 is off, turn the trip pointpotentiometer (P2) counter-clockwise until it just turns on. If the yellow LED does not turnon set DIP switch S5 to ON and repeat step 5.6.Slowly turn the trip point potentiometer (P2) clockwise until the yellow sensor status LED(L1) just turns off.3.6 Alarm Delay Function3.6Alarm Delay FunctionIf you want to slow the Pointek CLS300 response, to compensate for turbulence or falsereadings, set a delay interval using the delay potentiometer (P1) and set DIP switches S1and/or S2 to the OFF position to enable the delay for either alarm activation (S1 OFF), alarmde-activation (S2 OFF), or both (S1 and S2 OFF). (Note: This information can usually be foundinside the device cover.)If an immediate alarm output is critical, disable the delay by setting the appropriate switch(either S1 or S2) to ON. The functioning of switches S1 and S2 depends on the alarm setting:3.7Testing the Alarm DelayThis test procedure assumes that you have completed one of the calibration processesdescribed previously.1.Grasp the probe with your hand. The yellow sensor status LED (L1) should turn onimmediately. The red output status LED (L2) should turn on after a delay.2.Turn the delay potentiometer (P1) clockwise about 1/8 of a turn.3.Turn DIP switch S4 to the ON position; this will simulate a change in state of the probe(covered/uncovered).4.L1 (the yellow LED) should turn on immediately, and L2 (the red LED) should turn on after alonger delay than in Step 1.5.Turn DIP switch S4 to the OFF position.6.Continue to adjust the delay potentiometer (P1) until you have the desired delay.3.8OperationAfter completing the setup, replace the lid and secure the lid clip. Pointek CLS300 Standardmodel is now ready to operate.。

Specifications and dimensions subject to change Tactile SwitchesSpecifications and dimensions subject to changeHow To OrderPlease see chart below for full part numbers.SpecificationFUNCTION: Momentary actionCONTACT ARRANGEMENT: 1 make contact = SPST, N.O.ElectricalMAXIMUM VOLTAGE: 15 VDCMAXIMUM CURRENT DC: 20 mA DIELECTRIC STRENGTH: 250 VA C (1mn)CONTACT RESISTANCE: ≤ 100 mΩINSULATION RESISTANCE: ≥ 100 MΩ BOUNCE TIME:≤ 10 msEnvironmentalOPERATING TEMPERATURE:-20˚C to 70˚CProcessSOLDERING: This component is suited to the following methods: Infrared Reflow Soldering in accordance with IEC61760-1PackagingSwitches in reels of:5,000 pieces in 0.8 mm height 4,000 pieces in 1.5 mm heightDimensions of reels according to EIA 481B External diameter 330 mmNOTE : • Specifications listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center.•The PTS series is not certified for using in Automotive application and no PPAP. However, in the case of some automotive accessories and specific applications for 2 and 3 wheeled vehicles the PTS is widely used and very suitable. Please contact your local C&K representative to discuss your application and the bestswitch solution.Dimensions are shown: mmSpecifications and dimensions subject to changeRECOMMENDED PCB LAYOUT4,62,84,885,64,71,41,65,835,15,16,42,60,53,7`0,12,6(5,4)0,80,81,21,5Ø24,90,10,055,813421234SCHEMATIC1234656565Prohibited area for runSEE DETAILBDETAIL B SCALE 20PTS525 SMG15 SMTR2 LFS PTS525 SKG15 SMTR2 LFSDimensions are shown: mm Specifications and dimensions subject to change Tactile SwitchesDimensions are shown: mmSpecifications and dimensions subject to change3,434,45,44,65,60,75,25,24,94,90,53,7Ø 21,5`0,21,10,81342RECOMMENDED PCB LAYOUTSCHEMATIC12341234656565PTS525 SMG15J SMTR2 LFS PTS525 SKG15J SMTR2 LFSREEL0,5TAPE & REELT a c t i l e S w i t c h esSpecifications and dimensions subject to changeREELSCALE 0,5。

1Long-stroke Tactile Switches with High Operating Forces and Long Life.•High operating force also providing long life. (Reference values: OF = 5 N {510 gf}, Durability = 500,000 operations)•Long stroke achieved by using a rubber plunger. Model Number Legend1.Operating Force (OF)2.Packaging3.Special SpecificationList of Models / Operating CharacteristicsRoHS CompliantB3AL-100@ @ - @123SymbolMeaning 0 1.96 N {200 gf}1 2.45 N {250 gf}2 3.00 N {306 gf}3 3.50 N {357 gf}4 5.00 N {510 gf}5 4.50 N {459 gf}64.00 N {408 gf}Symbol Meaning PEmbossed tapeSymbol MeaningMSSwitch with middle strokeColor of pushbutton Red Green Black White (Milky-white)Brown Operating force (OF) 1.96±0.59 N {200±60 gf} 2.45±0.69 N {250±70 gf} 3.00±0.90 N {306±92 gf} 3.50±1.05 N {357±107 gf} 4.00±1.20 N {408±122 gf}Releasing force (RF) 0.24 N {24 gf} min. 0.49 N {50 gf} min.0.60 N {61 gf} min.0.70 N {71 gf} min.0.70 N {71 gf} min.Pretravel (PT) 1.3mmPackagingEmbossed tapeModelB3AL-1000P B3AL-1001PB3AL-1002PB3AL-1003PB3AL-1006PMinimum packing unit1,400 pcsColor of pushbutton Pink Blue Gray Yellow Operating force (OF) 4.50±1.35 N {459±138 gf} 5.00±1.50 N {510±153 gf}3.00±0.90 N {306±92 gf} 3.50±1.05 N {357±107 gf}Releasing force (RF) 0.70 N {71 gf} min. 1.00 N {102 gf} min. 0.60 N {61 gf} min.0.70 N {71 gf} min. Pretravel (PT) 1.3mm1.0±0.25mmPackagingEmbossed tapeModelB3AL-1005P B3AL-1004PB3AL-1002P-MSB3AL-1003P-MSMinimum packing unit1,400 pcs+0.2−0.3+0.2−0.32B3ALLong-stroke Tactile Switch (SMT)Ratings / CharacteristicsModel StructureDimensions(Unit: mm)Note:Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. No terminal numbers are indicated on the Switches.Rating (resistive load)1 to 50 mA at 5 to 16 VDCAmbient operating temperature -40°C to +90°C at 60%RH max. (with no icing or condensation)Ambient operating humidity 35% to 85% (at +5 to +35 °C)Contact configuration SPST-NO Contact resistance 100 m Ω max.Insulation resistance 100 M Ω min. (at 500 VDC with insulation tester)Dielectric strength 250 VAC, 50/60 Hz for 1 minBounce time 5 ms max. (The center of the plunger is pressed at a speed of 3 or 4 times per second.)Vibration resistance Malfunction: 10 to 55 Hz, 1.5-mm double amplitude Shock resistanceDestruction: 1,000 m/s 2 max.Malfunction: 100 m/s 2 max.DurabilityB3AL-1000P : 1,000,000 operations min.B3AL-1001P : 1,000,000 operations min.B3AL-1002P : 1,000,000 operations min.B3AL-1003P : 1,000,000 operations min.B3AL-1004P : 500,000 operations min.B3AL-1005P : 1,000,000 operations min.B3AL-1006P : 1,000,000 operations min.B3AL-1002P-MS : 1,000,000 operations min.B3AL-1003P-MS : 1,000,000 operations min.WeightApprox. 0.18 gPushbutton Plunger Moving contact Terminal (contact)BasePCB Pad (Top View)Terminal Arrangement/Internal Connections(Top View)3particles on the PCB, to enter the Switch, resulting in malfunc-tion.Packaging SpecificationsThe packaging specifications for B3AL Switches in embossed taping are given below.Dust CountermeasuresDo not mount or use the Switch in areas that are subject to dust. If dust is unavoidable, protect the Switch with a sheet or other countermeasure.Water and Drip ResistanceThe switch is not water or drip resistant. Do not use it in locations subject to water.(22)Reel13 d i a.380±2 d ia .Tape drawing directionTape drawing directionCross sectionC-C• Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product.• Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious influence on lives and property if used improperly. Make sure that the rating s and performance characteristics of the product provide a marg in of safety for the system or equipment, and be sure to provide the system or equipment with double safety mechanisms.Cat. No. A196-E1-060817(0207)(O)Note: Do not use this document to operate the Unit.OMRON CorporationElectronic and Mechanical Components CompanyContact: /ecb。

触摸屏中⽂说明书（只供参考-可编辑）前⾔为了您能尽快轻松⾃如地操作本机，在您开始使⽤本机之前，请仔细阅读我们随机提供的说明书，以便您能正确使⽤本机。

本⼿册中的信息资料如有变更，恕不另⾏通知，且不承担此⼿册产⽣的错误或者疏漏引起的任何事件。

⼀、主要功能·2.8⼨全触摸屏，320X240点阵全彩⾼速TFT显⽰屏全屏触摸·⽀持MP3、WMA、WA V⾳乐格式·⽀持MPEG-4(AVI)视频格式·⽀持JPEG格式图⽚浏览·内置麦克风，超长时间录⾳·节能设置，亮度可⾃由调节，⾃动关机·多种⾳效、循环可供选择·⽀持多国⽂字·USB2.0⾼速传输·⽀持电⼦书阅读·⽀持游戏功能，·移动硬盘功能·⽀持固件升级⽀持SD扩展，可⽀持到2GB SD卡⼆、外型及按键说明：1、本说明书中要求短按的时候您要在播放器上停留1S-2S，2、长按锁键可锁定机器的触摸屏，以防⽌误动作。

如需要解锁，请再长按锁键。

3、本机触摸屏可⽤⼿触摸，也可以⽤本机后壳上触摸笔孔中所带触摸笔进⾏操作。

三、主界⾯在主界⾯中，短按⼀下该菜单确认该功能，长按进⼊四、⾳乐播放在主菜单选择“⾳乐播放”选项，再长按进⼊⾳乐播放模式，进⼊以下界⾯：键选择上下曲，按调节⾳量。

2.按进⼊放⾳设置菜单。

其中设置⽅法和系统设置菜单中的⼀样，后来详述。

其中⾳效设置可设置成以下⼏种设置：，可选择正常（NOR）/3D/摇滚（ROCK）/流⾏（POP）/古典（CLASS）/重低⾳（BASS）/爵⼠（JAZZ）/⽤户⾃定（USER）8种⾳效模式。

3.按进⾏A-B复读短按⼀下，在播放状态下设置复读起始点，显⽰状态“A-”；再次短按，设置复读结束点，显⽰状态“A-B”，开始循环复读；短按“，，退出复读模式；在暂停状态下“A-B复读”功能⽆效。

当在“A-”、或“A-B”状态下，长按“”键进⾏快进或快退将取消“A-B复读”功能。

福建宏宇电子科技有限公司单火线单控开关接线示意图：智能触摸开关使用说明书安装前请仔细阅读说明书，任何不依照说明书的违规操作而出现产品损坏，厂家概不负责。

特别注意事项：1.避免带电安装，安装五分钟后可正常使用;2.必须严格按照接线示意图接线;3.每路所接灯具负载不得大于单路350W;4.接线盒为“86”标准型，尺寸大小至少为单火线双控开关使用配对说明：（HY-**1S/2S/3S ）75mm*75mm*32mm;1、对码 ：在电灯熄灭的状态下，长按开关某一个按键直至该 产品规格：路指示灯闪烁（灯同时也亮），再快速按下对应的另一个开关 1. 尺寸：86mm*86mm*36mm；上某一个按键（指示灯同时也闪），该路指示灯亮，对码成功。

2. 电压：交流110-260V/50Hz-60Hz；2、删除对码：长按本开关上要删除对码的按键。

指示灯3. 负载：单路350W；节能灯建议使用15W以上，效果更佳。

闪烁后停止，第二次闪烁时手离开，删码成功。

4. 待机功耗：<0.02mA（触摸开关）；（双控开关每个都要进行删码）5. 使用环境温度：-30~70℃；少于98%相对湿度；单火线双控开关接线示意图：6. 使用寿命：1000，000次操作。

安装示意图：注：1.灯具可接任意一个 开关上的L1/L2/L3;2.双控开关只有在配 对后，才能正常使用.售后服务：1.二年质保。

（非人为损坏情况下）2.十年维护。

单火线单控开关使用说明：（HY-**1/2/3）3.如有问题，请咨询当地经销商或直接拨打 售后中心电话：0591-********-813安装完本产品五分钟后通电，用手触摸按键，灯具开启备注：如开关出现常规无法正常操作现象，请关闭电闸， （指示灯为红色）， 关闭（指示灯熄灭背光灯长亮）。

断电五分钟后开启。

1火线输入23。