模具英语专业术语
模具述语
一、入水：gate
进入位： gate location
水口形式：gate type
大水口：edge gate
细水口： pin-point gate
水口大小：gate size
转水口： switching runner/gate
唧嘴口径： sprue diameter
二、流道: runner
热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate
圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance
热嘴： hot sprue
热流道板：hot manifold
发热管：cartridge heater
探针: thermocouples
插头： connector plug
插座： connector socket
密封/封料： seal
三、运水：water line
喉塞：line lpug
喉管：tube
塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker
四、模具零件： mold components 三板模：3-plate mold
二板模：2-plate mold
边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin
顶针板：ejector retainner plate
托板： support plate
螺丝： screw
管钉：dowel pin 开模槽：ply bar scot
内模管位：core/cavity inter-lock
顶针： ejector pin
司筒：ejector sleeve
司筒针：ejector pin
推板：stripper plate
缩呵：movable core,return core core puller
扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter
模胚（架）： mold base
上内模：cavity insert
下内模：core insert
行位（滑块）： slide
镶件：insert
压座/斜鸡：wedge
耐磨板/油板：wedge wear plate
压条：plate
撑头: support pillar
唧嘴： sprue bushing
挡板：stop plate
定位圈：locating ring
锁扣：latch
扣鸡：parting lock set
推杆：push bar
栓打螺丝：S.H.S.B
顶板：eracuretun
活动臂：lever arm
分流锥：spure sperader
水口司:bush
垃圾钉：stop pin
隔片：buffle
弹弓柱：spring rod
弹弓:die spring
中托司：ejector guide bush
中托边：ejector guide pin
镶针：pin
销子：dowel pin
波子弹弓：ball catch
喉塞: pipe plug
锁模块：lock plate
斜顶：angle from pin
斜顶杆：angle ejector rod
尼龙拉勾：parting locks
活动臂：lever arm
复位键、提前回杆：early return bar
气阀：valves
斜导边：angle pin
术语：terms
承压平面平衡：parting surface support balance
模排气：parting line venting
回针碰料位：return pin and cavity interference
模总高超出啤机规格：mold base shut hight
顶针碰运水：water line interferes withejector pin
料位出上/下模：part from cavith (core) side
模胚原身出料位：cavity direct cut on A-plate,core direct cut
on B-plate.
不准用镶件： Do not use (core/cavity) insert
用铍铜做镶件： use beryllium copper insert
初步（正式）模图设计：preliinary (final) mold design
反呵：reverse core
弹弓压缩量：spring compressed length 稳定性好：good stability,stable
强度不够：insufficient rigidity
均匀冷却：even cooling
扣模：sticking
热膨胀：thero expansion
公差：tolorance
铜公(电极）：copper electrode
Mold & die components 模具单元
Mold changing systems 换模系统
Mold core 模芯
Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修
Molds 模具
Pressing dies 压模
Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具
塑料模具 mould of plastics
注塑模具injection mould
冲压模具die
模架mould base
定模座板Top clamping plate
Top plate
Fixed clamp plate
水口推板stripper plate
A 板A plate
B 板B plate
支承板 support plate
方铁 spacer plate
底针板 ejector plate
面针板 ejector retainer plate
回针 Return pin
导柱 Guide pin
有托导套 Shoulder Guide bush
直导套 Straight Guide bush
动模座板Bottom clamp plate
Moving clamp plate
基准线datum line
基准面datum plan
型芯固定板core-retainer plate
凸模固定板punch-retainer plate
顶针ejector pin
单腔模具single cavity mould
多腔模具multi-cavity mould
多浇口multi-gating
浇口gate
缺料starving
排气breathing
光泽gloss
合模力mould clamping force
锁模力mould locking force
挤出extrusion
开裂crack
循环时间cycle time
老化aging
螺杆screw
麻点pit
嵌件insert
活动镶件movable insert
起垩chalking
浇注系统feed system
主流道 sprue
分流道runner
浇口gate
直浇口direct gate , sprue gate
轮辐浇口spoke gate , spider gate
点浇口pin-point gate
测浇口edge gate
潜伏浇口submarine gate , tunnel gate 料穴cold-slug well
浇口套sprue bush
流道板runner plate
排飞槽vent
分型线（面）parting line
定模stationary mould，Fixed mould 动模movable mould, movable half
上模upper mould， upper half
下模lower mould， lower half
型腔cavity
凹模cavity plate，cavity block
拼块split
定位销dowel
定位销孔dowel hole
型芯core
斜销angle pin, finger cam
滑块slide
滑块导板slide guide strip
楔紧块heel block, wedge lock
拉料杆sprue puller
定位环locating ring
冷却通cooling channel
脱模斜度draft 滑动型芯slide core
螺纹型芯threaded core
热流道模具hot-runner mould
绝热流道模insulated runner mould
熔合纹weld line （flow line）
三板式模具 three plate mould
脱模ejection
换模腔模具 interchangeable cavity mould 脱模剂release agent
注射能力shot capacity
注射速率injection rate
注射压力injection pressure
差色剂colorant
保压时间holdup time
闭模时间closing time
定型装置sizing system
阴模female mould，cavity block
阳模male mould
电加工设备Electron Discharge Machining 数控加工中心CNC machine center
万能铁床Universal milling machine
卧式刨床Horizontal planer
车床Engine lathe
平面磨床Surface grinding machine
去磁机Demagnetization machine
万能摇臂钻床Universal radial movable driller
立式钻床Vertical driller
超声波清洗机Ultrasonic clearing machine compre sion molding 压缩成型
flash mold 溢流式模具
plsitive mold 挤压式模具
split mold 分割式模具
cavity 型控母模
core 模心公模
taper 锥拔
leather cloak 仿皮革
shiver 饰纹
flow mark 流痕
welding mark 溶合痕
post screw insert 螺纹套筒埋值
self tapping screw 自攻螺丝
striper plate 脱料板
piston 活塞
cylinder 汽缸套
chip 细碎物
handle mold 手持式模具
（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）
two plate 两极式（模具）
well type 蓄料井
insulated runner 绝缘浇道方式
hot runner 热浇道
runner plat 浇道模块
valve gate 阀门浇口
band heater 环带状的电热器spindle 阀针
spear head 刨尖头
slag well 冷料井
cold slag 冷料渣
air vent 排气道
welding line 熔合痕
eject pin 顶出针
knock pin 顶出销
return pin 回位销反顶针
sleave 套筒
stripper plate 脱料板
insert core 放置入子
runner stripper plate 浇道脱料板guide pin 导销
eject rod (bar)（成型机）顶业捧subzero 深冷处理
three plate 三极式模具
runner system 浇道系统
stress crack 应力电裂
orientation 定向
sprue gate 射料浇口，直浇口nozzle 射嘴
sprue lock pin 料头钩销(拉料杆) slag well 冷料井
side gate 侧浇口
edge gate 侧缘浇口
tab gate 搭接浇口
film gate 薄膜浇口
flash gate 闸门浇口
slit gate 缝隙浇口
fan gate 扇形浇口
dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口
subarine gate 潜入式浇口tunnel gate 隧道式浇口
pin gate 针点浇口
Runner less 无浇道
(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣
emboss 凸点
dome 凸圆
semi-shearing 半剪
stamp mark 冲记号
deburr or coin 压毛边
punch riveting 冲压铆合
side stretch 侧冲压平
reel stretch 卷圆压平groove 压线
blanking 下料
stamp letter 冲字(料号) shearing 剪断
tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类
extension dwg 展开图procedure dwg 工程图
die structure dwg 模具结构图material 材质
material thickness 料片厚度factor 系数
upward 向上
downward 向下
press specification 冲床规格
die height range 适用模高
die height 闭模高度
burr 毛边
gap 间隙
weight 重量
total wt.总重量
punch wt.上模重量
五金零件类
inner guiding post 内导柱
inner hexagon screw 内六角螺钉dowel pin 固定销
coil spring 弹簧
lifter pin 顶料销
eq-height sleeves=spool 等高套筒pin 销
lifter guide pin 浮升导料销
guide pin 导正销
wire spring 圆线弹簧
outer guiding post 外导柱
stop screw 止付螺丝
located pin 定位销
outer bush 外导套
模板类
top plate 上托板（顶板）
top block 上垫脚
punch set 上模座
punch pad 上垫板
punch holder 上夹板
stripper pad 脱料背板
up stripper 上脱料板
male die 公模(凸模)
feature die 公母模
female die 母模(凹模)
upper plate 上模板
lower plate 下模板
die pad 下垫板
die holder 下夹板
die set 下模座
bottom block 下垫脚
bottom plate 下托板(底板)
stripping plate 内外打(脱料板)
outer stripper 外脱料板
inner stripper 内脱料板
lower stripper 下脱料板
零件类
punch 冲头
insert 入块(嵌入件)
deburring punch 压毛边冲子
groove punch 压线冲子
stamped punch 字模冲子
round punch 圆冲子
special shape punch 异形冲子
bending block 折刀
roller 滚轴
baffle plate 挡块
located block 定位块
supporting block for location
定位支承块
air cushion plate 气垫板
air-cushion eject-rod 气垫顶杆
trimming punch 切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch 压筋冲子
reel-stretch punch 卷圆压平冲子
guide plate 定位板
sliding block 滑块
塑料模具专业术语
动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate 动模座板 moving clamp plate. bottom clamping plate. bottom plate
上模座板 upper clamping plate
下模座板 lower clamping plate
凹模固定板 cavity-retainer plate
型芯固定板 core-retainer plate
凸模固定板 punch-retainer plate
模套 chase. bolster. frame
支承板 backing plate. supprr plate 垫块 spacer parallel
支架 ejector housing. mould base leg 压力铸造模具 die-casting die
压铸模零部件
定模 fixed die, cover die
定模座板 fixed clamping plate
定模套板 bolstor, fixed die
动模 moving die,ejector die
动模座板 moving clamping plate
直流道 sprue
横流道 runner
内浇口 gate
landed plunger mold||有肩柱塞式模具burnishing die||挤光模
landed positive mold||有肩全压式模具button die||镶入式圆形凹模
loading shoe mold||料套式模具
center-gated mold||中心浇口式模具loose detail mold||活零件模具
chill mold||冷硬用铸模
loose mold||活动式模具
clod hobbing||冷挤压制模
louvering die||百叶窗冲切模
composite dies||复合模具
manifold die||分歧管模具
counter punch||反凸模
modular mold||组合式模具
double stack mold||双层模具
multi-cavity mold||多模穴模具electroformed mold||电铸成形模
multi-gate mold||复式浇口模具expander die||扩径模
offswt bending die||双折冷弯模具extrusion die||挤出模
palletizing die||叠层模
family mold||反套制品模具
plaster mold||石膏模
blank through dies||漏件式落料模porous mold||通气性模具
duplicated cavity plate||复板模positive mold||全压式模具
fantail die||扇尾形模具
pressure die||压紧模
fishtail die||鱼尾形模具
profile die||轮廓模
flash mold||溢料式模具
progressive die||顺序模
gypsum mold||石膏铸模
protable mold||手提式模具
hot-runner mold||热流道模具prototype mold||雏形试验模具
ingot mold||钢锭模
punching die||落料模
lancing die||切口模
raising(embossing)||压花起伏成形
re-entrant mold||倒角式模具
sectional die||拼合模
runless injection mold||无流道冷料模具sectional die||对合模具
segment mold||组合模
semi-positive mold||半全压式模具shaper||定型模套
single cavity mold||单腔模具
solid forging die||整体锻模
split forging die||拼合锻模
split mold||双并式模具
sprueless mold||无注道残料模具squeezing die||挤压模
stretch form die||拉伸成形模sweeping mold||平刮铸模
swing die||振动模具
three plates mold||三片式模具trimming die||切边模
unit mold||单元式模具
universal mold||通用模具
unscrewing mold||退扣式模具
yoke type die||轭型模
模具钢材 khu?n thép
alloy tool steel 合金工具钢
aluminium alloy 铝合金钢
bearing alloy 轴承合金
blister steel 浸碳钢
bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢
clad sheet 被覆板
clod work die steel 冷锻模用钢
emery 金钢砂
ferrostatic pressure 钢铁水静压力
forging die steel 锻造模用钢
galvanized steel sheet 镀锌铁板
hard alloy steel 超硬合金钢
high speed tool steel 高速度工具钢
hot work die steel 热锻模用钢
low alloy tool steel 特殊工具钢
low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金
meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁
merchant iron 市售钢材
molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢
nickel chromium steel 镍铬钢prehardened steel 顶硬钢
silicon steel sheet 矽钢板
stainless steel 不锈钢
tin plated steel sheet 镀锡铁板
tough pitch copper 韧铜
troostite 吐粒散铁
tungsten steel 钨钢
vinyl tapped steel sheet 塑胶覆面钢板
塑件与模具compre sion molding压缩成型
flash mold溢流式模具
plsitive mold挤压式模具
split mold分割式模具
cavity型控母模
core模心公模
taper锥拔
leather cloak仿皮革
shiver饰纹
flow mark流痕
welding mark溶合痕
post screw insert螺纹套筒埋值
self tapping screw自攻螺丝
striper plate脱料板
piston活塞
cylinder汽缸套
chip细碎物
handle mold手持式模具
（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）
two plate两极式（模具）
well type蓄料井
insulated runner绝缘浇道方式
hot runner热浇道
runner plat浇道模块
valve gate阀门浇口
band heater环带状的电热器spindle阀针
spear head刨尖头
slag well冷料井
cold slag冷料渣
air vent排气道
welding line熔合痕
eject pin顶出针
knock pin顶出销
return pin回位销反顶针
sleave套筒
stripper plate脱料板
insert core放置入子
runner stripper plate浇道脱料板guide pin导销
eject rod (bar)（成型机）顶业捧subzero深冷处理
three plate三极式模具
runner system浇道系统
stress crack应力电裂orientation定向
sprue gate射料浇口，直浇口nozzle射嘴
sprue lock pin料头钩销(拉料杆) slag well冷料井
side gate侧浇口
edge gate侧缘浇口
tab gate搭接浇口
film gate薄膜浇口
flash gate闸门浇口
slit gate缝隙浇口
fan gate扇形浇口
dish gate因盘形浇口diaphragm gate隔膜浇口
ring gate环形浇口
subarine gate潜入式浇口
tunnel gate隧道式浇口
pin gate针点浇口
Runner less无浇道
(sprue less)无射料管方式
long nozzle延长喷嘴方式
sprue浇口;溶渣
零件类
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子bending block折刀
roller滚轴baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板bushing bolck衬套
cover plate盖板
guide pad导料块
模板类
top plate上托板（顶板）
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板
plain die简易模
pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔
forming成型(抽凸,冲凸) draw hole抽孔bending折弯
trim切边
emboss凸点
dome凸圆
semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线
blanking下料stamp letter冲字(料号) shearing剪断
tick-mark nearside正面压印tick-mark farside反面压印冲压名称类
extension dwg展开图procedure dwg工程图
die structure dwg模具结构图material材质
material thickness料片厚度factor系数
upward向上
downward向下
press specification冲床规格die height range适用模高die height闭模高度
burr毛边
gap间隙
weight重量
total wt.总重量
punch wt.上模重量
连接器connector
端子terminal
条型连接器bar connector
阴连接器Housing
阳连接器wafer
线束wire harness
间距space
额定电压 rated voltage
额定电流 rated current
接触电阻contact resistance 绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage
针pin 物料编号part number
导线wire
基体金属Base metal
电缆夹cable clamp
倒角chamfer
接触面积contact area
接触件安装孔contact cavity 接触长度contact length
接触件电镀层contact plating 接触压力contact pressure 接触件中心距contact space 接触簧片contact spring
插孔socket contact
法兰、凸缘Flange
界面间隙interfacial gap
键Key
键槽keyway
过渡段ramp
屏蔽套shielding
定位基准Datum reference
扁平电缆flat cable ，Ribbon cable
柔性印刷电线Flexible printed wiring
多层印制电路Multilayer printed circuit
焊盘pad
图形pattern
间距pitch
负极Negative pole
正极positive pole
回流Reflow
原理图Schematic diagram
单面板single sided board
双面板Two-sided board，Double-sided board
表面安装surface Mounting
翘曲warp， bow
波峰焊wave soldering
编织层braid
同轴电缆coaxial cable
电介质dielectric
电缆中导线的头数ends
外部干扰external interference
填充物filler
护套jacket
比重specific gravity
电阻的温度系数Temperature coefficient of resistance
模具
塑料模具mould of plastics
注塑模具injection mould
冲压模具die
模架mould base
定模座板Top clamping plate
Top plate
Fixed clamp plate
水口推板stripper plate A板A plate
B板B plate
支承板 support plate
方铁 spacer plate
底针板 ejector plate
面针板 ejector retainer plate
回针 Return pin
导柱 Guide pin
有托导套 Shoulder Guide bush 直导套 Straight Guide bush
动模座板Bottom clamp plate Moving clamp plate
基准线datum line
基准面datum plan
型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin
单腔模具single cavity mould 多腔模具multi-cavity mould
多浇口multi-gating
浇口gate
缺料starving
排气breathing
光泽gloss
合模力mould clamping force 锁模力mould locking force
挤出extrusion
开裂crack
循环时间cycle time
老化aging
螺杆screw
麻点pit
嵌件insert
活动镶件movable insert
起垩chalking
浇注系统feed system
主流道 sprue
分流道runner
浇口gate
直浇口direct gate , sprue gate
轮辐浇口spoke gate , spider gate
点浇口pin-point gate
测浇口edge gate
潜伏浇口submarine gate , tunnel gate 料穴cold-slug well
浇口套sprue bush
流道板runner plate
排飞槽vent
分型线（面）parting line
定模stationary mould，Fixed mould 动模movable mould, movable half
上模upper mould， upper half
下模lower mould， lower half
型腔cavity
凹模cavity plate，cavity block
拼块split
定位销dowel
定位销孔dowel hole
型芯core
斜销angle pin, finger cam
滑块slide
滑块导板slide guide strip
楔紧块heel block, wedge lock
拉料杆sprue puller
定位环locating ring
冷却通cooling channel
脱模斜度draft
滑动型芯slide core 螺纹型芯threaded core
热流道模具hot-runner mould
绝热流道模insulated runner mould
熔合纹weld line （flow line）
三板式模具three plate mould
脱模ejection
换模腔模具 interchangeable cavity mould 脱模剂release agent
注射能力shot capacity
注射速率injection rate
注射压力injection pressure
差色剂colorant
保压时间holdup time
闭模时间closing time
定型装置sizing system
阴模female mould，cavity block
阳模male mould
电加工设备Electron Discharge Machining 数控加工中心CNC machine center
万能铁床Universal milling machine
卧式刨床Horizontal planer
车床Engine lathe
平面磨床Surface grinding machine
去磁机Demagnetization machine
万能摇臂钻床Universal radial movable driller
立式钻床Vertical driller
超声波清洗机Ultrasonic clearing machine
模具零件
Top Plate 上托板（顶板）Top Block 上垫脚
Punch Set 上模座
Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板
Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板
Lower Mold Plate 下模板
Die Pad 下垫板
Die Holder 下夹板
Die Set 下模座
Bottom Block 下垫脚
Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板
Inner Stripper 内脱料板
Lower Stripper 下脱料板
Inner Guiding Post 内导柱
Inner Hexagon Screw 内六角螺钉
Dowel Pin 固定销
Mould Coil Spring 模具弹簧
Lifter Pin 顶料销
Isoheight Sleeve 等高套筒
Pin 销
Lifter Guide Pin 浮升导料销
Guide Pin 导正销
Wire Spring 圆线弹簧
Outer Guiding Post 外导柱
Stop Screw 止付螺丝
Located Pin 定位销
Outer Bush 外导套
Punch 冲头
Insert 入块（嵌入件）
Deburring Punch 压毛边冲子
Groove Punch 压线冲子
Stamped Punch 字模冲子
Round Punch 圆冲子
Special Shape Punch 异形冲子
Bending Block 折刀
Roller 滚轴
Baffle Plate 挡块
Located Block 定位块
Supporting Block for Location 定位支承块Air Cushion Plate 气垫板
Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子
Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子
Reel-stretch Punch 卷圆压平冲子
Guide Plate 定位板
Sliding Block 滑块
Sliding Dowel Block 滑块固定块
Active Plate 活动板
Lower Sliding Plate 下滑块板
Upper Holder Block 上压块
Upper Mid Plate 上中间板
Spring Box 弹簧箱
Spring-Box Eject-rod 弹簧箱顶杆
Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套
Cover Plate 盖板Guide Pad 导料块
模具技术用语
各种常用模具成形方式
Accurate Die Casting 精密压铸
Powder Forming 粉末成形
Calendaring Molding 压延成形
Powder Metal Forging 粉末锻造
Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造
Cold Forging 冷锻
Press Forging 冲锻
Compacting Molding 粉末压出成形
Rocking Die Forging 摇动锻造
Compound Molding 复合成形
Rotary Forging 回转锻造
Compression Molding 压缩成形
Rotational Molding 离心成形
Dip Mold 浸渍成形
Rubber Molding 橡胶成形
Encapsulation Molding 注入成形
Sand Mold Casting 砂模铸造
Extrusion Molding 挤出成形
Shell Casting 壳模铸造
Foam Forming 发泡成形
Sinter Forging 烧结锻造
Forging Roll 轧锻
Six Sides Forging 六面锻造
Gravity Casting 重力铸造
Slush Molding 凝塑成形
Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造
Hot Chamber Die Casting 热室压铸
Swaging 挤锻
Hot Forging 热锻
Transfer Molding 转送成形
Injection Molding 射出成形
Warm Forging 温锻
Investment Casting 精密铸造
Matched Die Method 对模成形法
Laminating Method 被覆淋膜成形
Low Pressure Casting 低压铸造
Lost Wax Casting 脱蜡铸造
Matched Mould Thermal Forming 对模热成形模
Close Mold 合模
Demould 脱模脱模剂
Mould Unloading 开模
Eject 顶出
Tool Change Retooling Die Changing 换模Mould Clamping 锁模
各式模具分类用语
Bismuth Mold 铋铸模
Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模
Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模
Loading Shoe Mold 料套式模具
Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具
Chill Mold 冷硬用铸模
Loose Mold 活动式模具
Cold Hobbing 冷挤压制模法
Louvering Die 百叶窗冲切模
Composite Dies 复合模具
Manifold Die 分歧管模具
Counter Punch 反凸模
Modular Mold 组合模具
Double Stack Mold 双层模具
Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模
Multi-Gate Mold 复式浇口模具
Expander Die 扩径模
Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模
Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具
Plaster Mold 石膏模
Blank Through Dies 漏件式落料模Porous Mold 通气性模具
Duplicated Cavity Plate 复板模
Positive Mold 全压式模具
Fantail Die 扇尾形模具
Pressure Die 压紧模
Fishtail Die 鱼尾形模具
Profile Die 轮廓模
Flash Mold 溢料式模具
Progressive Die 顺序模Gypsum Mold 石膏铸模
Portable Mold 手提式模具
Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模
Punching Die 落料模
Lancing Die 切口模切缝模
Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模
Runless Injection Mold 无流道冷料模具Sectional Die 对合模具
Segment Mold 组合模
Semi-Positive Mold 半全压式模具Shaper 定型模套
Single Cavity Mold 单腔模具
Solid Forging Die 整体锻模
Split Forging Die 拼合锻模
Split Mold 双并式模具
Sprueless Mold 无注道残料模具Squeezing Die 挤压模
Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模
Swing Die 振动模具
Three Plates Mold 三片式模具Trimming Die 切边模
Unit Mold 单元式模具
Universal Mold 通用模具
Unscrewing Mold 退扣式模具
Yoke Type Die 轭型模
模具厂常用之标准零配件
Air Vent Valve 通气阀
Anchor Pin 锚梢
Angular Pin 角梢
Baffle 调节阻板
Angular Pin 倾斜梢
Baffle Plate 折流档板
Ball Button 球塞套
Ball Plunger 定位球塞
Ball Slider 球塞滑块
Binder Plate 压板
Blank Holder 防皱压板
Blanking Die 落料冲头
Bolster 上下模板
Bottom board 浇注底板Bolster 垫板
Bottom Plate 下固定板Bracket 托架
Bumper Block 缓冲块
Buster 堵口
Casting Ladle 浇注包
Casting lug 铸耳
Cavity 模穴（模仁）
Cavity Retainer Plate 模穴托板Center Pin 中心梢
Clamping Block 锁定块
Coil Spring 螺旋弹簧
Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型
Core Pin 心型梢
Cotter 开口梢
Cross 十字接头
Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口
Die Approach 模头料道
Die Bed 型底
Die Block 块形模体
Die Body 铸模座
Die Bush 合模衬套
Die Button 冲模母模
Die Clamper 夹模器
Die Fastener 模具固定用零件Die Holder 母模固定板
Die Lip 模唇
Die Plate 冲模板
Die Set 冲压模座
Direct Gate 直接浇口
Dog Chuck 爪牙夹头
Dowel 定位梢
Dowel Hole 导套孔
Dowel Pin 合模梢
Dozzle 辅助浇口
Dowel Pin 定位梢
Draft 拔模锥度
Draw Bead 张力调整杆
Drive Bearing 传动轴承Ejection Pad 顶出衬垫
Ejector 脱模器
Ejector Guide Pin 顶出导梢
Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫
Ejector Pin 顶出梢
Ejector Plate 顶出板
Ejector Rod 顶出杆
Ejector Sleeve 顶出衬套
Ejector Valve 顶出阀
Eye Bolt 环首螺栓
Filling Core 填充型芯椿入蕊
Film Gate 薄膜形浇口
Finger Pin 指形梢
Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针
Flash Gate 毛边形浇口
Flask 上箱
Floating Punch 浮动冲头
Gate 浇口
Gate Land 浇口面
Gib 凹形拉紧楔
Goose Neck 鹅颈管
Guide Bushing 引导衬套
Guide Pin 导梢
Guide Post 引导柱
Guide Plate 导板
Guide Rail 导轨
Head Punch 顶头冲孔
Headless Punch 直柄冲头
Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头
Impact Damper 缓冲器
Injection Ram 压射柱塞
Inlay Bush 嵌入衬套
Inner Plunger 内柱塞
Inner Punch 内冲头
Insert 嵌件
Insert Pin 嵌件梢
King Pin 转向梢
King Pin Bush 主梢衬套
Knockout Bar 脱模杵
Land 合模平坦面
Land Area 合模面
Leader Bush 导梢衬套
Lifting Pin 起模顶针起模杆
Lining 内衬
Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢
Locating Ring 定位环
Lock Block 压块
Locking Block 定位块
Locking Plate 定位板
Loose Bush 活动衬套
Making Die 打印冲子
Manifold Block 歧管档块
Master Plate 靠模样板
Match Plate 分型板
Mold Base 塑胶模座
Mold Clamp 铸模紧固夹
Mold Platen 模用板
Moving Bolster 换模保持装置
Moving Bolster Plate 可动侧模板
One Piece Casting 整体铸件
Parallel Block 平行垫块
Parting Line 分模线
Parting Lock Set 合模定位器
Pass Guide 穴型导板
Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模
Pilot Pin 定位销导向销子
Pin Gate 针尖浇口
Plate 衬板
Pre Extrusion Punch 顶挤冲头
Punch 冲头
Puncher 推杆
Pusher Pin 衬套梢
Rack 机架
Rapping Rod 起模杆
Re-entrant Mold 凹入模
Retainer Pin 嵌件梢
Retainer Plate 托料板
Return Pin 回位梢
Riding Stripper 浮动脱模器
Ring Gate 环型浇口
Roller 滚筒Runner 流道
Runner Ejector Set 流道顶出器
Runner Lock Pin 流道拉梢
Screw Plug 头塞
Set Screw 固定螺丝
Shedder 脱模装置
Shim 分隔片
Shoe 模座之上下模板
Shoot 流道
Shoulder Bolt 肩部螺丝
Skeleton 骨架
Slag Riser 冒渣口
Slide（Slide Core）滑块
Slip Joint 滑配接头
Spacer Block 间隔块
Spacer Ring 间隔环
Spider 模蕊支架
Spindle 主轴
Sprue 注道
Sprue Bushing 注道衬套
Sprue Bushing Guide 注道导套
Sprue Lock Bushing 注道定位衬套
Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线
Square Key 方键
Square Nut 方螺帽
Square Thread 方螺纹
Limit Stop Collar 限位套
Stop Pin 止动梢
Stop Ring 止动环
Stopper 定位停止梢
Straight Pin 圆柱销
Stripper Bolt 脱料螺栓
Stripper Bushing 脱模衬套
Stripper Plate 剥料板
Stroke End Block 行程止梢
Submarine Gate 潜入式浇口
Support Pillar 支撑支柱顶出支柱
Support Pin 支撑梢
Supporting Plate 托板
Sweep Template 造模刮板
Tab Gate 辅助浇口
Taper Key 推拔键
Taper Pin 拔锥梢锥形梢
Teeming Pouring 浇注
Three Start Screw 三条螺纹
Thrust Pin 推力销
Tie Bar 拉杵
Tunnel Gate 隧道形浇口
Vent 通气孔
Wortle Plate 拉丝模板
模具术语翻译
动模 Movable Mould Moving Half
定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate
动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate
上模座板 Upper Clamping Plate
下模座板 Lower Clamping Plate
凹模固定板 Cavity-retainer Plate
型芯固定板 Mould Core-retainer Plate
凸模固定板 Punch-retainer Plate
模套 Die Body Die Sleeve Die Blank
支承板 Backing Plate Support Plate
垫块 Spacer Parallel
支架 Ejector Housing Mould Base Leg
模头 Die Head
根据国家标准，以下为部分压铸模具标准翻译。压力铸造模具 Die-Casting Die
定模 Fixed Die Cover Die
定模座板 Fixed Clamping Plate
定模套板 Bolster Fixed Die
动模 Moving Die Ejector Die
动模座板 Moving Clamping Plate
直流道 Sprue
横流道 Runner
内浇口 Gate
模具分类
Injection Mold 注塑模
Plastic Rubber Mould 塑胶模
Rubber Molding 橡胶成形
Hot Chamber Die Casting 热室压铸
Sand Mold Casting 砂模铸造
Extrusion Mold 挤出模
Multi-Cavity Mold 多模穴模具Plaster Mold 石膏模
Three Plates Mold 三板模
Plain Die 简易模
Pierce Die 冲孔模
Forming Die 成型模
Progressive Die 连续模
Gang Dies 复合模
Shearing Die 剪边模
Cavity Die 型腔模
Riveting Die 铆合模
Compression Molding 压缩成型
Flash Mold 溢流式模具
Extrusion Mold 挤压式模具
Split Mold 分割式模具
Mould Cavity 型腔母模
Mold Core 模芯公模
Large Die Mold 大型模具
Precise Die Mold 精密模具
Complex Die Mold 复杂模具
Foaming Mould 发泡模具
Metal Die 金属模具
Plastic Mold 塑料模具
Press Tool Stamping Die Punch Die 冲压模具Extrusion Die 挤压模具
Graphite Die 石墨模具
流道浇口部分
Runner System 浇道系统
Sprue Cold Material Trap 浇道冷料井
Sprue Puller 拉杆
Runner Design 流道设计
Main Runner 主流道
Secondary Runner 次流道
Mould Gate Design 浇口设计
Submarine Gate 潜伏浇口
Tunnel Gate 隧道式浇口
Pinpoint Gate 点浇口
Fan Gate 扇形浇口
Side Gate 侧浇口
Edge Gate 侧缘浇口
Tab Gate 搭接浇口
Film Gate 薄膜浇口
Dish Gate 盘形浇口
Diaphragm Gate 隔膜浇口
Ring Gate 环形浇口
Runnerless 无浇道
Sprueless 无射料管方式
Long Nozzle 延长喷嘴方式
Sprue 浇口，溶渣
Insulated Runner Hot Runner 热浇道Runner Plat 浇道模块
Valve Gate阀门浇口
Slag Well 冷料井
Cold Slag 冷料渣
Sprue Gate 射料浇口，直浇口Nozzle 射嘴
Sprue Lock Pin 料头钩销（拉料杆）
注塑缺陷
Flash 飞边
Warpage 翘曲
Air Trap 积风
Blush 发赤
Flow Line 流痕
Splay 银纹
Short Shot 短射
Sink Mark 缩痕
Streak 条纹
Void 缩孔
Weld Line 熔接线
Gas Mark 烧焦
Cold Slug 冷斑
Delamination 起皮
Burr 毛刺
Flaw Scratch 刮伤
Gloss 光泽
Glazing 光滑
Surface Check 表面裂痕
Hesitation 迟滞
注塑工艺
Molding Conditions 成型条件Drying 烘干
Barrel Temperature 料筒温度Melt Temperature 熔化温度
Mold Temperature 模具温度
Injection Pressure 注塑压力
Back Pressure 背压
Injection Speed 注塑速度
Screw Speed 螺杆转速
Tensile Strength 抗拉强度
Tensile Elongation 延伸率
Flexural Modulus 弯曲模数
Flexural Strength 抗弯强度
Shrinkage 收缩率
Regrind Usage 次料使用
Moulding 模塑
机械设备
Lathe 车床
Planer 刨床
Miller Milling Machine 铣床
Grinder 磨床
Driller 钻床
Linear Cutting 线切割
Electrical Sparkle 电火花
Welder 电焊机
Punching Machine 冲床
Robot 机械手
Common Equipment 常用设备
EDM Electron Discharge Machining 放电加工3D Coordinate Measurement 三次元量床Boring Machine 搪孔机
Contouring Machine 轮廓锯床
Copy Grinding Machine 仿形磨床Cylindrical Grinding Machine 外圆磨床
Die Spotting Machine 合模机
Engraving Machine 雕刻机
Engraving E.D.M 雕模放置加工机
Form Grinding Machine 成形磨床
Graphite Machine 石墨加工机
Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床
模具英语专业术语 模具述语 一、入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug
Counter bored hole 沉孔 Chamfer 倒斜角 Fillet 倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count 复盘点数量 Quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号
塑胶模具类中英文对照专业术语工程部/ Design department: 1) Designer - 设计师。 2) Assembly drawing - 模具组装图。 3) Mold layout - 模具结构图。 4) 2D product drawing - 2D产品图。 5) 3D product data - 3D产品数据。 6) Part drawing - 散件图。 7) Insert molding - 镶件模。 8) 2 color mold / Double injection tool - 双色模。 9) Hydraulic system - 油/水压系统。 10) Parting line - 分模线。 11) Air venting - 排气槽。 12) Cooling system - 冷却系统。 13) Screw - 镙丝。 14) Hot runner system - 热流道。 15) Valve gate - 伐针入水口。 16) Fan gate - 扇型入水口。 17) Pin point gate - 针点进胶。 18) Moon gate / Banana gate - 香蕉，象牙入水口。 19) Submarine gate - 潜水口。 20) Injection machine tonnage - 注塑机吨数。 21) Number of cavity - 穴数。 22) Steel - 钢材。 23) Copper - 铜。 24) Tungsten copper - 钨铜。 25) Beryllium copper - 铍铜。 26) Hardening - 加硬/淬火。 27) Tempering - 回火。
陶瓷 ceramics 合成纤维 synthetic fibre 电化学腐蚀 electrochemical corrosion 车架 automotive chassis 悬架 suspension 转向器 redirector 变速器 speed changer 板料冲压 sheet metal parts 孔加工 spot facing machining 车间 workshop 工程技术人员 engineer 气动夹紧 pneuma lock 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking
技术要求 technical requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear 直齿锥齿轮 straight bevel gear 运动简图 kinematic sketch 齿轮齿条 pinion and rack 蜗杆蜗轮 worm and worm gear 虚约束 passive constraint 曲柄 crank 摇杆 racker 凸轮 cams
实用文案 模具英语专业术语 模具述语开模槽：ply bar scot 内模管位：一、入水：gate core/cavity inter-lock 顶针：ejector pin 进入位：gate location 司筒：ejector sleeve 水口形式：gate type 司筒针：edge gate ejector pin 大水口：推板：细水口：stripper plate pin-point gate 缩呵：gate size movable core,return core core 水口大小：puller switching runner/gate 转水口：扣机（尼龙拉勾）：nylon latch lock sprue diameter 唧嘴口径：斜顶：lifter : runner 二、流道模胚（架）：mold base hot runner,hot manifold 热流道：上内模：cavity insert : hot sprue/cold runner 热嘴冷流道下内模：core insert : direct sprue gate 唧嘴直流行位（滑块）：slide round(full/half runner 圆形流道：镶件：insert mold flow analysis 流道电脑分析：压座/斜鸡：wedge :runner balance 流道平衡耐磨板/油板：wedge wear plate hot sprue 热嘴：压条：plate hot manifold 热流道板：撑头: support pillar cartridge heater 发热管：唧嘴：sprue bushing : thermocouples 探针挡板：stop plate connector plug 插头：定位圈：locating ring connector socket 插座：锁扣：latch seal 封料：/密封扣鸡：parting lock set water line 三、运水：推杆：push bar line lpug 喉塞：栓打螺丝：S.H.S.B tube 喉管：顶板：eracuretun plastic tube 塑胶管：活动臂：lever arm jiffy quick connector 快速接头：分流锥：spure sperader plug/socker 水口司mold components 四、模具零件：:bush 垃圾钉：三板模：3-plate mold stop pin 隔片：buffle 二板模：2-plate mold 弹弓柱：导边：/leader pin/guide pin spring rod 边钉弹弓:die spring 导套：边司/bushing/guide bushing 中托司：ejector guide bush 中托司：shoulder guide bushing 中托边：ejector guide pin guide pin ：L中托边镶针：ejector retainner plate 顶针板：pin 销子：托板：support plate dowel pin 波子弹弓：ball catch screw 螺丝：: pipe plug dowel pin 管钉：喉塞文案大全． 实用文案 锁模块：lock plate Mold repair 模具维修 angle from pin 斜顶：Molds 模具
模具术语英文翻译
模具术语英文翻译 根据国家标准，以下为部分塑料模具成形术语的标准翻译。 动模 Movable Mould Moving Half 定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate 动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate 下模座板 Lower Clamping Plate 凹模固定板 Cavity-retainer Plate 型芯固定板 Mould Core-retainer Plate 凸模固定板 Punch-retainer Plate 模套 Die Body Die Sleeve Die Blank 支承板 Backing Plate Support Plate 垫块 Spacer Parallel 支架 Ejector Housing Mould Base Leg 模头 Die Head 根据国家标准，以下为部分压铸模具术语的标准翻译。 压力铸造模具 Die-Casting Die 压铸模零部件 定模 Fixed Die Cover Die 定模座板 Fixed Clamping Plate 定模套板 Bolster Fixed Die 动模 Moving Die Ejector Die 动模座板 Moving Clamping Plate 直流道 Sprue 横流道 Runner 内浇口 Gate 模具分类 Injection Mold 注塑模 Plastic Rubber Mould 塑胶模 Rubber Molding 橡胶成形 Hot Chamber Die Casting 热室压铸 Sand Mold Casting 砂模铸造 Extrusion Mold 挤出模 Multi-Cavity Mold 多模穴模具 Stack Mold, Stack Injection Mould 叠层模
外文翻译 英文原文 Belt Conveying Systems Development of driving system Among the methods of material conveying employed，belt conveyors play a very important part in the reliable carrying of material over long distances at competitive cost．Conveyor systems have become larger and more complex and drive systems have also been going through a process of evolution and will continue to do so．Nowadays，bigger belts require more power and have brought the need for larger individual drives as well as multiple drives such as 3 drives of 750 kW for one belt(this is the case for the conveyor drives in Chengzhuang Mine)．The ability to control drive acceleration torque is critical to belt conveyors’ performance．An efficient drive system should be able to provide smooth，soft starts while maintaining belt tensions within the specified safe limits．For load sharing on multiple drives．torque and speed control are also important consideratio ns in the drive system’s design. Due to the advances in conveyor drive control technology，at present many more reliable．Cost-effective and performance-driven conveyor drive systems cov ering a wide range of power are available for customers’ choices[1]. 1 Analysis on conveyor drive technologies 1．1 Direct drives Full-voltage starters．With a full-voltage starter design，the conveyor head shaft is direct-coupled to the motor through the gear drive．Direct full-voltage starters are adequate for relatively low-power, simple-profile conveyors．With direct fu11-voltage starters．no control is provided for various conveyor loads and．depending on the ratio between fu11- and no-1oad power requirements，empty starting times can be three or four times faster than full load．The maintenance-free starting system is simple，low-cost and very reliable．However, they cannot control starting torque and maximum stall torque；therefore．they are
常用模具零件中英文对照表 2005-12-19 14:51:17???中国注塑网 入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis :?[??n?l?s?s] 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边：guide pin 顶针板：ejector retainer plate 托板：support plate
机械术语英文翻译 阿基米德蜗杆Archimedes worm 安全系数safety factor; factor of safety安全载荷safe load 凹面、凹度concavity扳手wrench 板簧flat leaf spring 半圆键woodruff key 变形deformation摆杆oscillating bar 摆动从动件oscillating follower 摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile 摆线运动规律cycloidal motion 摆线针轮cycloidal-pin wheel包角angle of contact 保持架cage背对背安装丨back-to-back arrangement 背锥back cone ；normal cone 背锥角back angle背锥距back cone distance比例尺scale 热容specific heat capacity 闭式链closed kinematic chain闭链机构closed chain mechanism 臂部arm 变频器frequency converters变频调速frequency control of motor speed 变速speed change 变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient 标准齿轮standard gear标准直齿轮standard spur gear 表面质量系数superficial mass factor 表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness 并联式组合combination in parallel并联机构parallel mechanism 并联组合机构parallel combined mechanism并行工程concurrent engineering 并行设计concurred design, CD不平衡相位phase angle of unbalance 不平衡imbalance (or unbalance)不平衡量amount of unbalance 不完全齿轮机构intermittent gearing波发生器wave generator 波数number of waves补偿compensation 参数化设计parameterization design, PD残余应力residual stress 操纵及控制装置operation control device槽轮Geneva wheel 槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate 槽凸轮groove cam侧隙backlash 差动轮系differential gear train差动螺旋机构differential screw mechanism 差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor 承载能力bearing capacity成对安装paired mounting 尺寸系列dimension series齿槽tooth space 齿槽宽spacewidth齿侧间隙backlash 齿顶高addendum齿顶圆addendum circle 齿根高dedendum齿根圆dedendum circle 齿厚tooth thickness齿距circular pitch 齿宽face width齿廓tooth profile 齿廓曲线tooth curve齿轮gear 齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack 齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter 齿轮机构gear齿轮轮坯blank 齿轮传动系pinion unit齿轮联轴器gear coupling 齿条传动rack gear齿数tooth number 齿数比gear ratio齿条rack 齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain 齿形系数form factor齿式棘轮机构tooth ratchet mechanism 插齿机gear shaper重合点coincident points 重合度contact ratio冲床punch
机械专业相关词汇中英文翻译大全 单价unit price 工日合计Man-day total/work-day total 人工费cost of labor 材料费materials expenses 机械的mechanical 检查接线connection test 发电机generator 调相机phase regulator 周波cycle 减负荷装置 load-shedding equipment 断路器柜circuit breaker cabinet 单母线single busbar 互感器transformer 每相电流Current by Phase 封闭式插接close type socket joint 发电机控制面板generator control panel 分级卸载sorted unloading 同步控制synchronization control 调速器 speed governor 信号屏signal screen 继电器relay 高压柜high pressure cabinet 油浸电力变压器oil-immersed power transformer 空气断路器air circuit breaker 控制屏control panel 直流馈电屏direct current feed control panel 电容器electric condenser 计量盘metering panel 成套配电箱whole set of distribution box 落地式floor model 控制开关Control switches 铜芯电力电缆Copper core power cable 控制电缆actuating cable 热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing 万用槽钢versatile U-steel 电缆托架 cable bracket 钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座 防爆插座Explosion-proof socket 接地绞线earthing twisted pair 接地母线 earthing bus
"R，L Co.,Ltd" 模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner Vents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing
三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug 撬模脚 Ppy Slot 重新加工Reworked 配件Components 补偿Compensation 平面度 Parallel 倒角Chamfer 模胚Mold Base 热嘴Hotnozzle 火花机 Edm 熔接线 Weildline 压机Press 晒纹Texturing 梯形Trapezoid 凸缘、法兰Flange 方铁Spacer Block 顶针板Ejector Plate 顶针底板Ejector Retainer Plate 垫板Retainer Plate
机械专业英语词汇 陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank
模具英语专业术语模具的分类: 冲压模(五金模): stamping die 分离模: cutting die 成形模: forming die 塑胶模: plastics mold 注射模: injection mold 压缩模: compression mold 铸塑模: transfer mold 吹塑模: blow mold 吸塑模: suck mold 铸造模: casting die 砂型铸造: sand casting 压铸模: die casting 锻造模: forging die 塑胶模具术语 一、入水：gate 进入位(入水点)：gate location 水口形式：gate type 大水口(侧浇口): edge gate 潜水口: sub-gate 薄膜式水口: film gate 牛角式潜水口: banana gate 扇形水口: fan gate 环形水口: ring gate 二次水口: 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 直接水口: direct gate 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形(整圆/半圆)流道：round(full/half) runner 矩形流道: rectangle runner 梯形流道: trapezoid runner U形流道: U shape runner 流道电脑分析(模流分析)：mold flow analysis 流道平衡: runner balance
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座：connector socket 密封/封料：seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝：screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）：mold base 上内模：cavity insert 下内模：core insert 行位（滑块）：slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴：sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin
模具名词中英文对照表序号中文名英文名 1一、水口gate 2进水位gate location 3水口形式gate type 4大水口edge gate 5细水口pin-point gate 6水口大小gate size 7转水口switching gate 8唧嘴口径sprue diameter 9二、流道runner 10热流道hot runner 11冷流道cold runner 12唧嘴直流direct sprue gate 13圆形流道round runner 14模流分析mold flow analysis 15流道平衡runner balance 16热嘴hot sprue 17热流道板hot manifold 18发热管cartridge heater 19探针thermocouples 20插头connector plug 21插座connector socket 22密封/封料seal 23三、运水water line 24喉塞line pug 25喉管tube 26塑胶管plastic tube 27快速接头jiffy quick connector plug 28四、模具零件mold components 29三板模three-plate mold 模具名词中英文对照表 序号中文名英文名 30二板模two-plate mold 31边钉/ 导边leader pin /guide pin
32边司/ 导套bush in g/guide bush ing 33顶针板ejector retainer plate 34托板support plate 35螺丝screw 36管钉dowel pin 37开模槽ply bar score 38内模管位core/cavity inter-lock 39顶针ejector pin 40司筒ejector sleeve 41司筒针ejector pin 42推板stripper plate 43缩呵movable core 44扣机（尼龙拉勾）n yl on latch lock 45斜顶lifter 46模胚（架）mold base 47母模cavity in sert 48公模core insert 49行位（滑块）slide 50 镶件in sert 51压座/斜鸡wedge 52耐磨板/ 油板wedge wear plate 53压条plate 54撑头support pillar 55唧嘴sprue bushing 56挡板stop plate 57定位圈locating ring 58锁扣latch 模具名词中英文对照表 序号中文名英文名 59扣鸡parti ng lock set 60推杆push bar 61栓打螺丝S.H.S.B 62顶板ejector plate 63活动臂lever arm
机械用语的英语翻译 恒温·干燥器/恒温恒湿器 Drying Ovens/Humidity Chambers 送风定温恒温器 Forced Convection Constant Temperature Ovens 惰性气体恒温器 Inert Gas Ovens 精密恒温器 Precision Constant Temperature Ovens 洁净恒温器 Clean Ovens 送风定温干燥器 Forced Convection Constant Temperature Drying Ovens 空气幕送风定温恒温器 Forced Convection Ovens With Air Curtain 定温干燥箱 Constant Temperature Drying Ovens 角形真空定温干燥器 Vacuum Drying Ovens 恒温恒湿器 Constant Temperature and Humidity Chambers 流水线设备 In-Line System for Underfill Adhesive and Encapsulation 恒温培养器 Constant Temperature Incubators--- 可程式低温培养器 Low Temperature Program Type Incubators 低温培养器 Low Temperature Incubators 低温稳定性培养器 Low Temperature Stability Incubators 培养器 Incubators CO2培养器 CO2 Incubators
振荡培养器 Shaking Incubators 冻结干燥器 Freeze Dryers--- 冻结干燥器 Freeze Dryers 离心形冻结干燥器 Centrifugal Freeze Dryers 灭菌器 Sterilizers--- 干热灭菌器 Drying Sterilizers 高压灭菌器 Autoclaves Sterilizers 低温等离子灭菌器 Low Temperature Plasma Sterilizers 环形燃烧管灭菌器 Loop Cinerator 纯水制造装置 Water Purifiers--- 纯水制造装置 Water Stills 超纯水制造装置 Ultra-pure Water Purifiers 简易纯水制造装置 Water Purifiers 超纯水制造装置系统 Ultra-pure Water Purifier System 大容量纯水制造装置 Water Purifiers System 洗净器 Washers--- 实验室玻璃器皿清洗机 Laboratory Glassware Washers 超声波清洗机 Ultrasonic Cleaners 大型超声波清洗机 Aqueous Ultrasonic Cleaning Systems 超声波试管清洗机 Ultrasonic Pipet Washers 超声波清洗机 Ultrasonic Cleaners