模具术语英文翻译 (2)

模具专业术语英语
模具专业涉及许多专业术语，在英语中对应的词汇如下：
1. Mold/Mould: 模具
2. Die: 模具，尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴，注塑道
6. Gate: 浇口，进料口
7. Ejector Pin: 顶针，用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽，模具凹槽
这些词汇在模具制造和加工过程中经常使用，涵盖了模具设计、制造和加工等方面的专业术语。

模具术语中英文对照模具(Mold) - A shaped cavity or matrix into which molten or uncured material is poured so thatupon solidification it will take on the shape of the cavity.注射模(Injection mold) - A molding cavity created by injecting material into a mold via a runner system.常用于塑料件注塑。

压铸模(Die casting mold) - A metal mold created for die casting processes, usually zinc, copper or aluminum based alloys.充型范(Pattern) - A full sized model of the desired casting, used to create the mold cavity in processes like sand casting.冒口(Sprue) - The primary vertical channel through which liquid material is poured into mold cavities.冒口通过主要供料道向模板腔内引入熔融金属。

气孔(Vent) - A small channel allowing the gases formed (by vaporization,chemical reaction etc.) to escape from mold cavity.用来排出模具腔内气体的小通道。

流道(Gate) - The channel that conveys molten metal from the sprue into the mold cavity.将熔融金属从主流道(冒口)引入模腔的小槽道。

模具常用专业术语中英文对照塑料模具常用专业术语中英文对照模胚（架）：mold base 三板模（细水口）：3-plate mold二板模（大水口）：2-plate 定位圈（法栏）locating ring 浇口套（唧嘴）sprue bushing热流道：hot runner,hot manifold面板:cavity adaptor plate 水口板：runner stripper plate上模板（A板）:cavity plate 下模板（B板）:core plate 上内模（型腔＼母模＼凹模）：cavity insert下内模（型芯＼公模＼凸模）：core insert推板：stripper plate模脚（方铁）spacer plate 顶针板：ejector retainner plate托板(顶针底板)：support plat垃圾钉：stop pin撑头: support pillar底板：core adaptor plate 推杆：push bar顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin回针：push bake pin导柱：leader pin/guide pin 导套：bushing/guide bushing中托司（顶针板导套）：shoulder guide bushing中托边(顶针板导柱)：guide pin滑块（行位）：slide波子弹弓（定位珠）：ballcatch耐磨板/油板：wedge wear压条：plate斜导边（斜导柱）：angle压座/铲鸡：wedge斜顶：angle from pin斜顶杆：angle ejector rod 缩呵：movable core,return core core puller尼龙拉勾（扣机）：nylon latch lock栓打螺丝：S.H.S.B镶针：pin喉塞: pipe plug锁模块：lock plate挡板：stop plate螺丝：screw推板：stripper plate斜顶：lifterplate塑胶管：plastic tube快速接头：jiffy quick connector plug/socker mold内模管位：core/cavity inter-lockflash(塑件)毛边电极(铜公)：copper electrode五金模具常用专业术语中英文对照cutting die, blanking die冲progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling 线拉伸engraving, to engrave刻印top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate 底板（下托板）stripping plate 脱料板（表里打）outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板上模座upper die set成型公form punch脱料板stripper垫板subplate/backupplate下模座die plate垫脚parallel托板mounting plate顶料销kick off初始管位first start pin带肩螺丝shoulder screw两用销lifter pin弹簧护套spring cage拔牙螺丝jack screw侧冲组件cam section导正装置guide equipment 漏废料孔slug hole 刀口trim line 入子insert护套bushing 整形公restrike forming punch止挡板stop plate 挂台head扣位pocket of head 导柱guide post导套guide bushing 油嘴oil nipple接刀口mismatch/cookie bites限位块stop block挡块stopper浮块lifter压块keeper靠块heel对正块alignment block闭合高度shut hight上夹板/固定座holder/retainer下模座lower die set 成刑母公forming die 码模槽mounting slot 球锁紧固定座ball-lock 导尺rail送料板rail plate倒角chamfer销钉dowel尖角sharp --angle普通弹簧coil spring 镶件insert插针pilot pin顶杆lifter bolt起吊孔handing hole 垫片shim/wear-plate 键槽key slot沉孔counter hole导正块thrust block。

模具工业中英文翻译模具常用术语中英文对照局部视图 Partial View冷料# Cold Slag线切割 Wire E.D.M轮廊 Contour螺纹孔 Tapping Hole连接件 Fittings斜针 Angle Pin接合 Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机 Specific Press水嘴接头 Water Fittings螺纹 Eyebolt Thread回针 Stop Pin二级顶出针Sub-Leaderd Pin镶件 Mold Insert 加硬 Harden唧嘴 Sprue设计筒图 Design Preliminary名称块表 Title Block版本标识 Revision Level材料清单 Stock List制模 Build Mold手动滑块 Hand Slide漏水测试 Leak Test流道排气 Runner Vents抛光 Draw Polish侧抽芯 Side Action加强筋 Reinforcing三角撑 Gusset柱子 Bossed出模斜度 Draft外廊 Contour落单会议 Kick-Off Meeting装卸孔 Handling Hole运输安全带 Moldstrap码模槽 Clamp Slot撑头 Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location耐落胶 Teflon Paste偏移量 Offset水塞 Water Line Plug撬模脚 Ppy Slot重新加工 Reworked配件 Components补偿 Compensation平面度 Parallel倒角 Chamfer模胚 Mold Base热嘴 Hotnozzle火花机 Edm熔接线 Weildline压机 Press晒纹 Texturing梯形 Trapezoid凸缘、法兰 Flange方铁 Spacer Block顶针板 Ejector Plate顶针底板 Ejector Retainer Plate垫板 Retainer Plate后模镶针 Core Pin拉圾钉 Stop Pin有托顶针 Shoulder Ejector Pin顶针板导套 Guided Ejection Bushing针板导柱 Guided Ejection Leader Pin唧嘴 Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing定位圈（法兰） Locating Ring管钉（定位销） Dowel Pin管状管钉 Tubular Dowel吊环 Safety Hoist Ring日期印 Dating Insert环保印 Recycling Insert气顶 Air Poppet Valve截水口镶件 Runner Shut-Off Insert早回 Early Ejector Return加速项 Accelerated Ejector客户 Client 产品名 Part Name产品编号 Part No 缩水 Shrinkage版本 Rev 模胚 Mold Base下模镶件 Core Block上模镶件 Cavity Block小镶件 Sub-Insert下模小镶件 Core Sub-Insert上模小镶件 Cavity Sub-Insert行位 Slide行位镶件 Slide Insert压条 Gib压紧块（铲机） Jaw硬片（摩擦片） Wear Plate水口铁 Runner Bar上模水口铁 Upper Runner Bar下模水口铁 Lower Runner Bar弹簧 Spring水口勾针 Sprue Puller Pin顶针 Ejector Pin撑头 Support Pillar直身锁 Side Lock斜度锁 Interlock锁模板 Safety Bar‘O’令（密封圈） O'Ring喉塞 Plug隔水片 Baffle波子螺丝（行位定位螺丝） Ball-Catch 斜顶 Lifter控制开关 Switch回针 Return Pin斜导柱 Angle Pin推板 Stripper PlateA’板 A'PlateB’板 B'Plate方铁（垫铁）Spacer Block顶针板 Ejector Plate顶针底板 Ejector Retainer Plate垫板 Retainer Plate垃圾钉 Stop Pin有托顶针 Shoulder Ejector Pin顶针板导套 Guided Ejection Bushing针板导柱 Guided Ejection Leader Pin唧嘴 Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing定位圈（法兰） Locating Ring管钉（定位销） Dowel Pin管状管钉 Tubular Dowel吊环 Safety Hoist Ring日期印 Dating Insert环保印 Recycling Insert气顶 Air Poppet Valve截水口镶件 Runner Shut-Off Insert早回 Early Ejector Return加速顶 Accelerated Ejector扁顶 Blade 出模斜波 Draft手动滑块模具 Hand Slide-In Type Mold回针板 Backup合模 Shutoff空隙槽 Clearance Slot导柱及导套 Leader Pin Bushing水口拉钩 Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold 三板模 3-Plat Mold分型面 Parting Line司筒 Ejector Sleeve垫圈 Washer熔接线（夹水纹） Weldline吸针 Sucker Pin回针板 Retainer Plate顶出板 Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开 Cut Of Position预先决定 Preload缓冲器 Bumper衬垫 Cushion公差 Tolerance突然性动作 Slam销针 Dowel钩槽 Gib精磨 Finished通框 Through Window粘后模 Sticking Core粘水口 Sticking Sprue夹水纹 Weld Line变形 Warpage走水不平均 Filling Uneven走不齐 Short Shot挂成品 Part Hanging漏水 Water Leakage刮花（擦伤） Galling漏电 Ele Leakage困气 Air Trapping温度 Temperature注塑模 Injection Mold入水 Gate试板 Sampling压力 Pressure倒圆 Fillet顶棍 Ejector顶白 Stress Mark粘前模 Sticking Cav名称块表 Title Block版本标识 Revision Level材料清单 Stock List斜导柱（斜边） Angle PinA板 A'plateB板 B'plate倒扣 Under-Cut披峰 Flash缩水 Sink Mark氮化 Nitride不规则四边形Trapezoid缩水 Shrinkage连续的 Consecutive雕刻 Engrave出模角 Draft分模面 Parting Surface擦位 Shut-Off(S/0)导套 Bushing回针 Return Pin加硬 Harden唧嘴 Sprue设计筒图 Design Preliminary 丝印 Silkprint不干胶 Adhesive Sticker导向针 Guide Din公差 Tolerance线切割 Wire-Cut电火花 Edm抛光 Polishing蚀纹 Texture探热针 Thermocouple三打螺丝毫（限螺丝） Stripper Bolt 盖板 Cover Plate齿轮 Gear油唧 Hydraulic Cylinder司筒 Ejector Sleeve导柱 Leader Pin冷料# Cold Slag线切割 Wire E.D.M.轮廓 Contour螺纹孔 Tapping Hole连接件 Fittings斜针 Angle Pin接合 Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头 Water Fittings螺纹 Eyebolt Thread回针 Stop Pin二级顶出针 Sub-Leader Pin镶件 Mold Insert锁定位 Lock楔子(铲鸡) Wedge高产量模量 High V olume Running Mold 剖面图 Cross Section 模具结构 Mold Construction模芯 Parting Core局部视图 Partial View热流道 Manifold热嘴 Hot Nozzle型腔数 Cav No模号 Mold No胶料 Material尺寸 Dimension重要尺寸 Critical Dimension雕刻 EngraveAssembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试V oltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor 副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzer蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/ 承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明yearend physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/ good parts 良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack 上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机。

模具专业英语一：入水：gate进入位：gate location 水口形式：gate type 大水口：edge gate细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道：runner热流道：hot runner,hot manifold 唧嘴直流：direct sprue gate流道电脑分析：mold flow analysis 热嘴：hot sprue发热管:cartridge heater插头： connector plug密封/封料：seal—、运水：water line塑胶管:plastic tube四、模具零件：mold components热嘴)令流道:hot sprue/cold runner圆形流道:round(full∕half runner流道平衡:runner balance热流道板：hot manifold探针:thermocouples插座：connector socket快速接头：jiffy quick connector plug/socker二板模:2-plate mold边司/导套:bushing/guide bushing 中托边L ： guide pin托板: support plate管钉：dowel pin内模管位:core/cavity inter-lock司筒：ejector sleeve推板：stripper plate缩呵：movable core, return core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）：mold base 上内模：cavity insert下内模：core insert 行位（滑块）：slide镶件：insert耐磨板/油板：wedge wear plate撑头：support pillar挡板：stop plate锁扣：latch推杆:push bar顶板：eracuretun分流锥：spure sperader垃圾钉：Stop pin弹弓柱:spring rod中托司：ejector guide bush 镶针：pin 波子弹弓:ball catch压座/斜鸡：wedge压条：plate唧嘴:sprue bushing定位圈:locating ring扣鸡:parting lock set栓打螺丝：S.H.S.B活动臂:lever arm水口司:bush隔片:buffle弹弓:die spring中托边:ejector guide pin销子：dowel pin喉塞:line lpug 喉管：tube三板模:3-plate mold边钉/导边:leader pin/guide pin 中托司：shoulder guide bushing 顶针板：ejector retainer plate 螺丝：screw开模槽:P∣y bar scot顶针：ejector pin司筒针∙ejector pin模具成形不良用语英汉对比aberration 色差atomization 彳匕blacking hole涂料孔（铸疵）blister 起泡blooming 起霜body wrinkle侧壁皱纹bubble 膜泡burn mark 糊斑cell气泡center buckle表面中部波皱chipping修整表面缺陷collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation变形edge切边碎片edge crack 裂边fading 退色filler speak填充料斑fissure裂纹flange wrinkle凸缘起皱flaw刮伤flow mark 流痕galling 毛边glazing光滑gloss光泽grease pits ）亏斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick割痕orange peel橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀bank mark 料纹bite咬入blacking scab 涂料疤low hole 破孔blushing 泛白breaking-in 冒口带肉burr毛边camber翘曲check细裂痕checking龟裂clamp-off铸件凹痕plate mark模板印痕pock麻点pock mark 痘斑resin streak 树脂流纹resin wear树脂脱落riding凹陷sagging 松垂saponification 皂化scar疤痕scrap废料scrap jam废料堵塞scratch刮伤/划痕scuffing深冲表面划伤seam裂痕shock line模口挤痕short shot充填不足shrinkage pool 凹孑I sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak条状痕surface check表面裂痕surface roughening橘皮状表皮皱折surging波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹各式模具分类用语英汉对比landed plunger mold有肩柱塞式模具burnishing die 挤光模landed positive mold有肩全压式模具button die镶人式圆形凹模loading shoe mold料套式模具center-gated mold中心浇口式模具loose detail mold活零件模具chill mold冷硬用铸模loose mold活动式模具clod hobbing冷挤压制模lowering die百叶窗冲切模composite dies复合模具manifold die分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold复式浇口模具expander die扩径模offswt bending die双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold反套制品模具plaster mold 石膏模blank through dies漏件式落料模porous mold通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die扇尾形模具pressure die压紧模fishtail die鱼尾形模具profile die轮廓模flash mold溢料式模具progressive die挨次模gypsum mold 石膏铸模protable mold 手提式模具 hot-runner mold 热流道模具 prototype mold 雏形试验模具 ingot mold 钢锭模 punching die 落料模lancing die 切口模 raising(embossing)压花起伏成形 re-entrant mold 倒角式模具 sectional die 拼合模 runless injection mold 无流道冷料模具 sectional die 对合模具 segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具 solid forging die 整体锻模 split forging die 拼合锻模 split mold 双并式模具sprueless mold 无注道残料模具 squeezing die 挤压模 stretch form die 拉伸成形模 sweeping mold 平刮铸模swing die 振动模具 three plates mold 三片式模具 trimming die 切边模 unit mold 单元式模具universal mold 通用模具 unscrewing mold 退扣式模具 yoke type die 规型模各种模具常用成形方式英汉对比accurate die casting 精密压铸 powder forming 粉末成形 calendaring molding 压延成形 powder metal forging 粉末锻造 cold chamber die casting 冷式压铸 precision forging 精密锻造 cold forging 冷锻 press forging 冲锻 compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 复合成形 rotary forging 回转锻造 compression molding 压缩成形 rotational molding 离心成形dip mold 浸'溃成形rubber molding 橡胶成形 encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming 泡成形 sinter forging 烧结锻造 forging roll 轧锻 six sides forging 六面锻造gravity casting 重力铸造 slush molding 凝塑成形 hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻 hot forging 热锻transfer molding 转送成形injection molding 射出成形 warm forging 温锻 investment casting 精密铸造 matched die method 对模成形法 laminating method 被覆淋膜成形 low pressure casting 彳氐压铸造 lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形机械类常用英语：冲压模具•零件类special shape punch 异形冲子 bending block 折刀 roller 滚轴 baffle plate 挡块 located block 定位块supporting block for location 定位支承块机械类常用英语：冲压模具•模板类trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子punch 冲头insert 入块（嵌入件） deburring punch 压毛边冲子 groove punch 压线冲子 stamped punch 字模冲子 round punch 圆冲子air cushion plate 气垫板 air-cushion eject-rod 气垫顶杆ribbon punch 压筋冲子reel-stretch punch卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder 上夹板stripper pad脱料背板up stripper上脱料板male die公模（凸模）feature die 公母模female die母模（凹模）upper plate 上模板upper mid plate 上中间板spring box弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad导料块lower plate 下模板die pad下垫板die holder下夹板die set下模座bottom block 下垫脚bottom plate下托板（底板）stripping plate内外打（脱料板）outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板冲压模具.冲压名称类英汉对比reel stretch卷圆压平groove压线blanking 下料stamp letter 冲字（料号）shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印extension dwg 绽开图procedure dwg 工程图die structure dwg模具结构图material 材质material thickness 料片厚度factor系数upward向上downward 向下press specification 冲床规格die height range 适用模高die height闭模高度plain die简易模pierce die冲孔模forming die 成型模progressive die 连续模gang dies复合模shearing die 剪边模riveting die 钏合模pierce冲孔forming成型（抽凸，冲凸）draw hole 抽孔bending 折弯trim切边emboss凸点dome凸圆semi-shearing 半剪stamp mark冲记号deburr or coin 压毛边punch riveting 冲压枷合burr毛边total wt.总重量 punch wt.上模重量模具工程常用词汇英汉对比high-speed transmission 高速传递 heat dissipation 热传 rack 上料 degrease 脱脂 rinse 水洗 alkaline etch 龄咬 desmut 剥黑膜 D.l. rinse 纯水次 Chromate 铭酸处理 Anodize 阳性处理 seal 封孔 revision 版次 part number/P/N 料号 good products 良品 scraped products 报放心品 defective products 不良品 finished products 成品 disposed products 处壬里品 barcode 条码 flow chart 流程表单 assembly 组装 stamping 冲压 molding 成型spare parts=buffer 备品 coordinate 座标 dismantle the die 折模 auxiliary faction 帮助功能 poly-line 多义线 heater band 加热片 thermocouple 热电偶 sand blasting 喷沙 grit 砂砾derusting machine 除锈机 degate 打浇口 dryer 烘干机 induction 感应 induction light 感应光gap 间隙 weight 重量ram 连杆 edge finder 巡边器 concave 凸 convex Γtj l short 射料不足 nick 缺口 speck 瑕 shine 亮班 splay 银纹 gas mark 焦痕 delamination 起鳞 cold slug 冷块 blush 导色 gouge 沟槽;凿槽 satin texture 段面咬花 witness line 证示线 patent 专利 grit 沙砾granule=peuet=grain 细粒 grit maker 抽粒机 cushion 缓冲 magnalium 镁铝合金 magnesium 镁金 metal plate 板金 lathe 车 mill 铿 plane 包∣J grind 磨 drill 铝 boring 锋 blinster 气泡 fillet 镶;嵌边through-hole form 通孔形式 voller pin formality 滚针形式 cam driver 锄楔 shank 摸柄response=reaction=interaction 感应velocity 速度production tempo生产进度现状torque扭矩spline=the multiple keys 花键quenching 淬火tempering 回火annealing 退火carbonization 碳化alloy合金tungsten high speed steel 鸨高速的moly high speed steel 铝高速的模具工程常用词汇英汉对比stock age analysis sheet库存货龄分析表on-hand inventory 现有库存available material 良品可使用obsolete material 良品已呆滞to be inspected or reworked 待验或重工total合计part number/ P/N 料号type形态item/group/class 类另，quality 品质prepared by 制表notes 说明cause description 缘由说明终盘点差异分析表physical inventory 盘点数量physical count quantity 帐面数量difference quantity 差异量cause analysis 缘由分析raw materials 原料materials 物料finished product 成品semi-finished product 半成品packing materials 包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts 不良品disposed goods 处理品warehouse/hub 仓库on way location 在途仓oversea location 海外仓spare parts physical inventory list 备品盘点清单spare molds location 模具备品仓organic solvent 有机溶剂bracket小磁导liaison联络单volatile挥发性resistance 电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破裂机skid/pallet 栈板to× machine 自旬∣1 机wire EDM 线割EDM放电机coil stock 卷料sheet stock 片料tolerance 工差score=groove 压线cam block 滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head 挂钩槽slug hole废料孔feature die 公母模expansion dwg 绽开图radius半径shim(wedge)楔子torch-flame cut 火焰切割set screw止付螺丝form block 折刀Stop pin定位销round pierce punch=die button 圆冲子shape punch=dιe insert 异形子stock locater block 定位块under cut=scrap chopper 清角active plate 活动板baffle plate 挡块cover plate 盖板male die 公模female die 母模groove punch压线冲子air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板bushing block 衬套insert入块club car高尔夫球车capability 力量parameter 参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping 脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization 去磁;消磁模具工程常用词汇英汉对比padding block 垫块stepping bar 垫条upper die base 上模座lower die base 卜模座upper supporting blank 上承板upper padding plate blank 上垫板spare dies模具备品spring弹簧bolt螺栓document folder 文件夹file folder 资料夹to put file in order 整理资料spare tools location 手工备品仓first count 初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment 设施waste materials 废料work in progress product 在制品casing = containerazation 装箱quantity of physical invetory second count 复盘点数量quantity of customs countdie模具figure file, chart file 图档cutting die, blanking die 冲裁模progressive die, follow (-on)die连续模compound die 复合模punched hole 冲孔panel board 镶块to cutedges=side cut=side scrap 切边to bending 折弯to pull z to stretch 拉伸Line streching, line pulling 线拉伸engraving, to engrave 亥(JEfl upsiding down edges 翻边to stake 钏合designing, to design 设计design modification 设计变化die block 模块folded block 折弯块sliding block 滑块location pin 定位销lifting pin 顶料销die plate, front board 模板会计师盘,点数量the first page 第一联filed by accounting department for reference 会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will besent to financial department) physical inventory card年终盘点卡与清册使用一状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing 工程试模材米斗not included in physical inventory 不歹∣j入盘点sample样品incoming material to be inspected 进货待验description 品名steel/rolled steel 钢材物料统计明细表approved by / checked by / prepared by 核准/审核/办PCE assembly production schedule sheetPCE组装厂生产排配表model机铺work order 工令revision 版次remark 备注production control confirmation 生产确认checked by 初审approved by 核准department 部门模具钢材alloy tool steel合金工具钢aluminium alloy 铝合金钢bearing alloy轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel碳素工具钢clad sheet被覆板clod work die steel 冷锻模用钢emery金钢砂ferrostatic pressure 钢铁水静压力forging die steel锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel超硬合金钢high speed tool steel高速度工具钢hot work die steel热锻模用钢low alloy tool steel 特别工具钢low manganese casting steel 彳氐镒铸钢marging steel马式体高强度热处理钢martri× alloy马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron市售钢材molybdenum high speed steel 铝系高速钢molybdenum steel 铝钢nickel chromium steel 银铭钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈与冈tin plated steel sheet 镀锡铁板meeting minutes 会议纪l录meeting type 会另!jdistribution department 分发单位location 地点chairman 主席present members 出席人员subject 主题conclusion 结论decision items 决议事项responsible department 负责单位pre-fixed finishing date 预定完成日模具钢材及零件英语tough pitch copper 韧铜vinyl tapped steel sheet 塑料覆面钢板零件英语一塑件&模具相关英文leather cloak 仿皮革 shiver 饰纹 flow mark 流痕 welding mark 溶合痕post screw insert 螺纹套筒埋值 self tapping screw 自攻螺丝 striper plate 脱料板 piston 活塞 cylinder 汽缸套 chip 细碎物handle mold 手持式模具移转成型用模具encapsulation molding 低压封装成型 射出成型用模具two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式 hot runner 热浇道 runner plat 浇道模块 valve gate 阀门浇口 band heater 环带状的电热器 spindle 阀针 spear head 刨尖头 slag well 冷料井 cold slag 冷料渣 airvent 排气道 h=0.02~0.05mm w=3.2mm L=3~5mm welding line 熔合痕 eject pin 顶出针 knock pin 顶出销 return pin 回位销反顶针 sleave 套筒stripper plate 脱料板 insert core 放置人子runner stripper plate 浇道脱料板 guide pin 导销eject rod （bar ）（成型机）顶业捧troostite 吐粒散铁 tungsten steel 鸨钢punch 冲头insert 入块（嵌入件） deburring punch 压毛边冲子 groove punch 压线冲子 stamped punch 字模冲子 round punch 圆冲子special shape punch 异形冲子 bending block 折刀 roller 滚轴 baffle plate 挡块 located block 定位块supporting block for location 定位支承块 air cushion plate 气垫板 air-cushion eject-rod 气垫顶杆 trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子 ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子 guide plate 定位板 sliding block 滑块sliding dowel block 滑块固定块 active plate 活动板 lower sliding plate 卜滑块板 upper holder block 上压块 upper mid plate 上中间板 spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆 spring-box eject-plate 弹簧箱顶板 bushing bolck 衬套 cover plate 盖板 guide pad 导料块compre sion molding 压缩成型 flash mold 溢流式模具 P ∣sitive mold 挤压式模具 split mold 分割式模具 cavity 型控母模 core 模心公模 taper 锥拔subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation 定向sprue gate射料浇口，直浇口nozzle射嘴slag well冷料•井side gate 侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate 闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=l∕2rl∕5tT=2.5~3.5mmdiaphragm gate 隔膜浇口ring gate环形浇口subarine gate 潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less 无浇道（sprue less）无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣sprue lock pin料头钩销（拉料杆）压铸die-cast注塑injection铸件casting/cast/founding起泡/气泡bubble/blister/airbubble缺料short-shots/undershot浇不足/*铸under-founding多料superfluities/superfluous material （alloy）顶针痕ejector（pins） mark彳白纹flow mark/flow line冷纹cold mark/cold streak油纹oil streak走水纹splash mark银纹silver streaks霜纹splay mark夹水纹silver streaks/flow line/weld line扣模/粘模spruesticking砂眼/气眼air hole（塑胶件）弯曲/变形warping/warpage变形deformation扭曲twist翅曲warp/warped材料错误usingwrong plastic material凸痕convex mark凹位/凹陷sink mark/dent mark 模具徐§披锋flashingftt损pare-mark/cutmark批凹pare off柱纹trim-mark/file-mark铿损excessivetrim mark黑点/黑纹black spots/black streak发白white mark烧焦burnmarks刮花/刮痕scratch mark擦痕/擦伤rub-mark/brush-burn裂缝cracking裂纹crakingline51tS stress mark起皮chip错位（合模线）Parting line misalignment孔位尺寸转变dimensionvarious哑色dull color表面变光滑（喷油面）glossy finishing表面sruface/outside镶件insert/insert word缩水/收缩sinkmark/shrinkage/shrink mark偏差colordeviation色粉colourment 颜色colour/color斜针 Angle Pin 接合 Engage替换镶件 Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头 Water Fittings 螺纹 Eyebolt Thread 回针 Stop Pin二级顶出针 Sub-Leaderd Pin 镶件 Mold Insert 加硬 Harden 唧嘴 Sprue设计筒图 Design Preliminary 名称块表 Title Block 版本标识 Revision Level 材料清单 Stock List 制模 Build Mold 手动滑块 Hand Slide 漏水测试Leak Test 流道排气 Runner Vents 抛光 Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing 三角撑Gusset 柱子 Bossed 出模斜度Draft 外廊 Contour落单会议 Kick-Off Meeting 装卸孔 Handling Hole 运输平安带Moldstrap 码模槽Clamp Slot 撑头 Support Pillar螺牙 1/2-13 Eye Bolt l∕2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量Offset 水塞 Water Line Plug 撬模脚Ppy Slot 重新加工 Reworked 配件 Components 补偿 Compensation 平面度Parallel 倒角 Chamfer 模胚 Mold Base零件污糟 dirty mark on part I 页白 stressmark/ejector mark 屈曲bent夹模线移位 part line misalignment 胶件料厚不均 uneven wall thickness 水口料 degradedmaterial 凹印 sink mark 擦花 abrasionmark ，昆色 contamination mark 热点不良 poor heat sticking 模具方面： 定位圈 locating ring 唧嘴spruebush （浇口套） A 板Aplate （定模板） B 板Bplate （动模板） 方铁 spacer block （垫铁）底板bottom clamp p ∣ate （动模底板） 面板top clamp p ∣ate （定模底板） 顶针ejector pin （顶杆） 直边钉guide pin （导柱） 托司 shoulder guide bush （^⅛） 直司 straight guide bush （导柱） 回针returnpin （回程杆） 细水口边钉support pin （副导柱） 蓝弹簧blue spring （回程弹簧） 水口推板 runner stripper plate （卸流道板）中边钉ejector guide pin （顶板导柱） 顶针板ejector retainer p ∣ate （顶杆固定板）顶针底板ejectorplate （顶杆垫板） 撑头support pollar （支撑柱） 垃圾钉stop pin （限位钉） 呵core （后模肉内镶件）后模肉back mold body （后模镶件） 前模肉cavity （前模镶件） 扣鸡P-lock 模芯 Parting Core 局部视图 Partial View 冷料# Cold Slag 线切割 轮廊 Contour热嘴Hotnozzle火花机Edm熔接线Weildline压机Press哂纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延长式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw 硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar下模水□铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar'0'令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch斜顶Lifter掌握开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA'板A'PlateB'板B,Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延长式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold 三板模3-Plat Mold分型面Parting Une司筒Ejector Sleeve垫圈Washer熔接线（夹水纹）Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动平安开关Electrical-Safety Switch 脱开Cut Of Position预先打算Preload缓冲器Bumper衬■垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping 温度Temperature注塑模Injection Mold入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA 板A'plateB 板B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规章四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off（S∕0）导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子（铲鸡）Wedge高产量模量High Volume Running Mold 剖面图Cross Section模具结构Mold Construction模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension雕刻Engrave托司EJ.GUIDE PIN。

模具专业英文术语大全1. Die - 模具2. Mold - 模具3. Cavity - 型腔4. Core - 芯子5. Ejector pin - 顶杆6. Land - 分型面7. Gate - 浇口8. Filleting - 去毛刺9. Trim - 修整10. Draft - 拔模斜度11. Undercut - 底切12. Flash - 飞边13. Warpage - 翘曲14. Shrinkage - 收缩15. Melt flow rate - 熔融指数16. Injection molding - 注塑成型17. Blow molding - 吹塑成型18. Compression molding - 压缩成型19. Vacuum molding - 真空成型20. Overmolding - 包覆成型21. Co-injection molding - 双色注塑成型22. Gas assist injection molding - 气体辅助注塑成型23. Rotational molding - 旋转成型24. Injection compression molding - 注射压缩成型25. Injection blow molding - 注射吹塑成型26. Injection stretch blow molding - 注射拉伸吹塑成型27. Injection transfer molding - 注射传递成型28. Injection foam molding - 注射发泡成型29. Injection gas assisted rotational molding - 注射气体辅助旋转成型30. Injection compression blow molding - 注射压缩吹塑成型31. Injection stretch blow molding - 注射拉伸吹塑成型32. Injection transfer blow molding - 注射传递吹塑成型33. Injection foam blow molding - 注射发泡吹塑成型34. Injection gas assisted transfer molding - 注射气体辅助传递成型35. Injection compression foam molding - 注射压缩发泡成型36. Injection stretch foam molding - 注射拉伸发泡成型37. Injection transfer foam molding - 注射传递发泡成型38. Injection gas assisted foam blow molding - 注射气体辅助发泡吹塑成型39. Injection compression foam blow molding - 注射压缩发泡吹塑成型40. Injection stretch foam blow molding - 注射拉伸发泡吹塑成型41. Injection transfer foam blow molding - 注射传递发泡吹塑成型42. Injection gas assisted compression molding - 注射气体辅助压缩成型43. Injection gas assisted stretch blow molding - 注射气体辅助拉伸吹塑成型44. Injection gas assisted transfer blow molding - 注射气体辅助传递吹塑成型45. Injection gas assisted foam compression molding - 注射气体辅助发泡压缩成型46. Injection gas assisted foam stretch blow molding - 注射气体辅助发泡拉伸吹塑成型47. Injection gas assisted foam transfer blow molding - 注射气体辅助发泡传递吹塑成型48. Injection gas assisted compression foam molding - 注射气体辅助压缩发泡成型49. Injection gas assisted stretch foam blow molding - 注射气体辅助拉伸发泡吹塑成型50. Injection gas assisted transfer foam blow molding - 注射气体辅助传递发泡吹塑成型51. Mold temperature control system - 模具温度控制系统52. Coolant system - 冷却系统53. Ejector system - 顶出系统54. Feed system - 喂料系统55. Packaging machine - 包装机56. Automated guided vehicle (AGV) - 自动导引车（AGV）57. Robotic arm - 机械臂58. Computer numerical control (CNC) machine - 计算机数控（CNC）机床59. Plastics injection machine - 塑料注塑机60. Plastics extruder - 塑料挤出机61. Plastics blow molding machine - 塑料吹塑机62. Plastics injection compression molding machine -塑料注塑压缩成型机63. Plastics injection stretch blow molding machine - 塑料注塑拉伸吹塑成型机64. Plastics injection transfer molding machine - 塑料注塑传递成型机65. Plastics injection foam molding machine - 塑料注塑发泡成型机66. Plastics injection gas assisted rotational molding machine - 塑料注塑气体辅助旋转成型机67. Plastics injection compression foam molding machine - 塑料注塑压缩发泡成型机68. Plastics injection stretch foam molding machine - 塑料注塑拉伸发泡成型机69. Plastics injection transfer foam molding machine - 塑料注塑传递发泡成型机70. Plastics injection gas assisted foam blow molding machine - 塑料注塑气体辅助发泡吹塑成型机71. Plastics injection compression foam blow molding machine - 塑料注塑压缩发泡吹塑成型机72. Plastics injection stretch foam blow molding machine - 塑料注塑拉伸发泡吹塑成型机73. Plastics injection transfer foam blow moldingmachine - 塑料注塑传递发泡吹塑成型机74. Plastics injection molding machine with movable platen - 带活动模板的塑料注塑机75. Plastics injection molding machine with fixed platen - 带固定模板的塑料注塑机76. Plastics injection molding machine with hot runner system - 带热流道系统的塑料注塑机77. Plastics injection molding machine with cold runner system - 带冷流道系统的塑料注塑机78. Plastics injection molding machine with multi-cavity design - 带多腔设计的塑料注塑机79. Plastics injection molding machine with clamping force control - 带夹紧力控制的塑料注塑机80. Plastics injection molding machine with cycle time reduction - 带循环时间缩短的塑料注塑机81. Plastics injection molding machine with energy saving features - 带节能功能的塑料注塑机82. Plastics injection molding machine with high precision control - 带高精度控制的塑料注塑机83. Plastics injection molding machine with automatic tool changing system - 带自动换模系统的塑料注塑机84. Plastics injection molding machine with roboticautomation - 带机器人自动化的塑料注塑机85. Plastics injection molding machine with quality control system - 带质量管理系统的塑料注塑机86. Plastics injection molding machine with process monitoring system - 带工艺监控系统的塑料注塑机87. Plastics injection molding machine with maintenance reminder system - 带维护提醒系统的塑料注塑机88. Plastics injection molding machine with data logging and analysis - 带数据记录和分析的塑料注塑机89. Plastics injection molding machine with remote control and monitoring - 带远程控制和监控的塑料注塑机90. Plastics injection molding machine with safety features - 带安全功能的塑料注塑机91. Plastics injection molding machine with operator interface - 带操作员界面的塑料注塑机92. Plastics injection molding machine with easy cleaning system - 带易清洁系统的塑料注塑机93. Plastics injection molding machine with quick change tooling - 带快速换模装置的塑料注塑机94. Plastics injection molding machine with low noiseoperation - 带低噪音运行的塑料注塑机95. Plastics injection molding machine with high throughput capacity - 带高产量能力的塑料注塑机96. Plastics injection molding machine with energy recovery system - 带能量回收系统的塑料注塑机97. Plastics injection molding machine with environmental protection features - 带环保功能的塑料注塑机98. Plastics injection molding machine with advanced materials compatibility - 带先进材料兼容性的塑料注塑机99. Plastics injection molding machine with customizable options - 可定制选项的塑料注塑机100. Plastics injection molding machine with reliable performance and durability - 具有可靠性能和耐用性的塑料注塑机。

模具英语专业术语如下：1. 模具：Mold，Die2. 模具设计：Mold Design3. 模具制造：Mold Manufacturing4. 模具工程师：Mold Engineer5. 模具材料：Mold Material6. 耐磨材料：wear-resistant material7. 热处理：Heat Treatment8. 水路设计：Water Path Design9. 浇注系统：Injection Sleeve10. 冷却系统：Cooling System11. 顶出系统：Pop-out System12. 复位系统：Reset System13. 导向机构：Guide Device14. 模板：Base Plate15. 顶杆：Pushrod16. 复位杆：Reset Rod17. 斜导柱：Oblique Guide Column18. 导套：Guide Bushing19. 滑块：Slider20. 镶针：Pillow Block21. 弹簧：Spring22. 皮囊弹簧：Kelvin Spring23. 油压缓冲器：Hydraulic Buffer24. 压力表：Pressure Gauge25. 安全阀：Safety Valve26. 水路板：Waterway Plate27. 分流器：Flow Divider28. 水口：Filler Port29. 冷料穴：Cold Molding Chamber30. 模具钢：Mold Steel31. SKH-55、SKH-55M、高速工具钢、HSS等。

32. SKD、SKH-S、SKD61、SKH-9等。

模具钢硬度（Hardness of die steel）：布氏硬度（HB）、洛氏硬度（HRC）、维氏硬度（HV）等。

33. SKD61(级硬SKD61) ，Cr12MoV，A3，A2，SKH-9，718，738，P20等。

塑料模具钢有PXZ、SACD、S136、S718、SS446、3Cr2Mo等。

模具专业英语词汇摘要：模具是一种用于生产特定形状的产品的工具，它在制造业中有着广泛的应用。

模具专业英语词汇是指与模具相关的专业术语，它涉及到模具的设计、制造、检验、使用等方面。

本文根据不同的主题，整理了一些常用的模具专业英语词汇，并用表格的形式进行了展示，以便于读者学习和参考。

1. 模具类型模具是一种用于生产特定形状的产品的工具，它可以分为不同的类型，根据加工方法和材料的不同，可以分为以下几类：中文英文注塑模injection mold压铸模die-casting mold冲压模stamping mold挤出模extrusion mold吹塑模blow mold硅胶模silicone mold砂型模sand mold石膏模plaster mold三板模three-plate mold双色模two-color mold2. 模具结构模具结构是指模具的组成部分和连接方式，它决定了模具的功能和性能。

一般来说，一个完整的模具由以下几个部分组成：中文英文模架mold base模芯core模腔cavity浇口系统gate system导向系统guiding system顶出系统ejection system冷却系统cooling system3. 模架模架是指支撑和固定模芯、模腔等部件的基础结构，它通常由标准件或定制件组成。

常见的模架部件有：中文英文定模座板fixed clamping plate动模座板moving clamping plate定模套板fixed bolster plate动模套板moving bolster plate支承板backing plate垫块spacer block4. 模芯和模腔模芯和模腔是指与被加工材料直接接触并形成产品形状的部件，它们通常由钢材或其他硬质材料制成。

常见的与模芯和模腔相关的术语有：中文英文凹面（内型面）concave surface (inner surface)凸面（外型面）convex surface (outer surface)分型面（合型面）parting surface (matching surface)型芯固定板（凸模固定板）core-retainer plate (punch-retainer plate)凹模固定板（凸模固定板）cavity-retainer plate (die-retainer plate)5. 浇口系统浇口系统是指将熔融或液态材料从注塑机或压铸机输送到型腔中的通道，它包括浇口、流道、冷料井等部件。

模具术语英文翻译模具技术是一门中高级技能，常用于制造各种零部件、产品的模具。

在与国际市场接轨的过程中，模具术语的英文翻译变得越来越重要。

以下是一些常用模具术语英文翻译：1. 模具（Mold）模具是指用于制造特定形状物品的工具，通常由钢或其他金属制成。

它们用于制造例如塑料零件、金属零件和玻璃等商品。

2. 模架（Mold Base）模架是模具的基础部分，也被称为模板。

它通常由大块钢制成，并用于支持模具的其余部分。

3. 插件（Insert）插件是用于增斜、瘦请求和其他加工部分的附件。

插件通常由钢等材料制成。

4. 加工孔（Cavity）加工孔是在模具内部用于形成零件结构的空心。

加工孔的大小和形状根据需要的零件而异。

5. 顶出杆（Ejector Pin）顶出杆是必要的部分，用于把再生塑料零件从模具中弹出。

它们使用弹性杆或气缸控制。

6. 轴套（Bush）轴套是另一种常见的模具部件，用于滑动组件之间的空间，以减少摩擦和磨损。

7. 冷却热器（Coolingheater）冷却热器是一种制冷装置，用于控制模具内的温度和湿度。

冷却热器可以提高零件的产量和质量。

8. 硬化切割（Hard mill）硬化切割是指用于在硬材料上切割零件形状的切割装置。

硬化切割工具通常使用钨钢。

9. 发涂（Run-out）发涂是指铸造过程中塑料流动输出的最终部分。

发涂通常用于旁边的零件切割、顶出杆操作和其他细节。

10. 设计文件（Design file）设计文件是囊括设计所需所有信息的文件。

设计文件通常包括设计图纸、CAD模型等。

总结这些术语虽然只是模具技术中的一部分，但对于模具制造和使用至关重要。

正确理解这些术语的英文翻译有助于与国际市场接轨，并且可以提高制造效率和精度，从而减少了生产成本和减少浪费。

无论领域还是地理位置，它们都是通用的，这也证明了模具技术的重要性和普及性。