推拉门五金解决方案新成员 — Slido Design 80-M

推拉门的设计原理
推拉门的设计原理基于滑动机构，通过将门扇与门框之间的狭缝进行连接并利用滑动装置，使门扇能够在水平方向上移动从而打开和关闭。

具体设计原理如下：
1. 门框设计：提供门扇移动所需的轨道和滑动空间。

门框通常由两块竖直立柱和一个顶横梁组成，门扇可在门框上滑动。

2. 滑动装置：门扇上安装有滑动装置，包括滚轮、导轨等。

滑动装置使门扇能够平稳地在门框上滑动，保持门扇的稳定性。

3. 导向系统：门扇的顶部和底部安装有导向系统，以确保门扇在滑动过程中保持与门框的对齐。

这些导向系统可包括轨道、导轨、滑槽等。

4. 手柄和拉手：门扇上设有手柄和拉手，便于用户推拉门。

手柄和拉手可以通过向上或向下拉动门扇来打开或关闭门。

5. 缓冲系统：为了防止门扇关闭时发生冲击或损坏，可以安装缓冲系统。

缓冲系统可以通过减缓门扇的速度来达到缓冲效果，保护门扇和滑动装置。

综上所述，推拉门的设计原理主要是依靠滑动装置和导向系统，通过门扇的推拉
和滑动来实现打开和关闭。

这种设计原理使得推拉门具有灵活、方便、节省空间的特点，广泛应用于建筑物、商店、公共场所等地方。

80系列推拉塑窗说明一、本图集窗框厚度构造尺寸为80，称为80系列推拉塑窗，（以下简称塑窗）二、本图集绘制了组合窗拼接节点图，根据工程需要，利用拼樘料能满足900-1800之间的各种形式的转角，组合成其它形式的悬窗、门连窗及特殊塑钢窗。

三、推拉窗可带外纱窗，纱窗可以推拉、拆装方便。

四、为确保80系列推拉窗能承受最大风荷要求，其窗框、窗扇的构造应具有可靠的刚度。

80系列塑料构件按下述规定长度，其内腔必须衬“加强筋”型钢。

窗框长度≥1450mm窗扇宽度≥700mm窗扇高度≥1100mm注：a、“加强筋”厚度不小于1.2mmb、“加强筋”型钢表面应经防锈处理c、“加强筋”型钢装配时，每根构件中装配螺钉数量应不少于3个，其间距最大不超过300mm。

五、窗框和窗扇的焊接角强度均应≥4000N。

六、推拉窗可根据不同地区、不同建筑物构造选择不同结构形式。

所列窗型抗风压性能见基本窗立面承受最大风荷值计算表。

标准窗（1500*1500）空气渗透性能实测值可达到1.0m3/h.m,雨水渗漏性能实测值可达到150Pa，保温性能实测值可达2W/m2K;隔声性能实测值可达30dB。

上述性能与产品规格，附件质量、生产厂家的生产技术质量、管理水平有密切的关系，用户宜根据生产厂家实测情况选用。

七、在推拉窗框（扇）的下部开设排水孔，排水孔一般为φ5mm长15～25mm的孔缝，室外要加排水孔封盖。

八、塑钢门窗的特性：1、保温、隔热、隔声、耐潮湿、耐腐蚀等性能，均优于其它金属门窗。

2、防火性能：不自然、不助燃、能自燃、氧指数不小于35%。

3、外观质量：表面光洁美观，不用油漆保养，能在—40℃～70℃的环境温度下正常使用三十年上。

4、塑钢门窗除不能与下列化学物质：发烟硫酸、硝酸、醋酸、氯气（干、湿性）、丙酮、四氯化炭、甲苯接触外，任何腐蚀性气体和粉尘作用的条件下均适用。

FURNITURE SLIDING DOOR HARDWARECOPLANAR SLIDING DOOR HARDWARE 4 EKU-FRONTINO 20 H OS UPPER 5 EKU-FRONTINO 20 H LOWER 6 A-FIL NANO 8 A-FIL MEDIUM 10 A-FIL 2 12 A-FIL 3 14 SLIDER S20 - FOR UPPER CABINET 16 SLIDER S20 - FOR LOWER CABINET 17 EKU-FRONTINO 40 H FS 18 ON LINE - 2 19 ON LINE LARGE 20 ON LINE - 3 21 SLIDER L70 - LARGE 22 SLIDER L70 - 3 DOORS 23 CINETTO PS40.1 - 2 DOORS 24 CINETTO PS40.1 - 3 DOORS 25STANDARD SLIDING DOOR HARDWARE 26 RICHELIEU SLIDE 27 DUCASSE AL 1535 WD 28 EKU-CLIPO 15 H IS 29 EKU-CLIPO 15 H MS 30 EKU-CLIPO 16 H IS 31 EKU-CLIPO 16 HM IS 32 EKU-CLIPO 16 H FS 33 EKU-CLIPO 26 H IS 34 EKU-CLIPO 26 H MS 35 EKU-CLIPO 36 H IS 36 EKU-CLIPO 36 HM IS 37 EKU-REGAL A 25 H FS 38 CINETTO PS10 39 CINETTO PS48 40 HAWA-ANTEA 50 & 80 FS 42 DUCASSE AL 1535 GL 45 EKU-CLIPO 16 GPK/GPPK IS 46 EKU-CLIPO 36 GPK/GPPK IS 47 EKU-CLIPO 36 G IS 48BI-FOLDING/BYPASSING SLIDING CLOSET DOOR HARDWARE 49 DUCASSE PL 2550 50 KLEIN PANELPAR 12/22E 51 CINETTO PS11 52 DUCASSE CD 40 CX 53 DUCASSE DUCLOSET SIMPLE 54 DUCASSE DUCLOSET DOUBLE 55 DUCASSE CA 4585 56 DUCASSE DN 50 CLIP 57KN CROWDER C-2025 KIT 58KN CROWDER C-600 59KN CROWDER C-400 60 HAWA-DORADO 40/IS 61 HAWA-209 70/MF 62SPECIALTY/INNOVATIVE SLIDING DOOR HARDWARE 63 HAWA-CONCEPTA 25 64 HAWA-CONCEPTA 30 65 HAWA-CONCEPTA 40 66 HAWA-CONCEPTA 50 67 HAWA-FOLDING CONCEPTA 25 SHORT 68 HAWA-FOLDING CONCEPTA 25 TALL 69 HAWA-APERTO 40F 70 HAWA-220 PLANFRONT 71 BORTOLUZZI MOVER 72 EKU LIBRA 20 SYNCHRO 73 EKU LIBRA 20 H IS/FS 74 SUGATSUNE MONOFLAT FAD-20 75 SUGATSUNE MONOFLAT LIN-X600 76 SUGATSUNE MONOFLAT FAD-44/44L 77 SUGATSUNE MONOFLAT UNISON 78 DOOR STRAIGHTENER 79TABLE OF CONTENTS3COPLANAR SLIDING DOOR HARDWAREEKU-FRONTINO 20 H OS UPPEREKU-FRONTINO 20 H LOWERFEATURESThe EKU-FRONTINO 20 H LOWER is a bottom running sliding system for twocoplanar doors weighing up to 44 lb (20 kg) each. The system makes itergonomically easy to open two flush mounted cabinet doors, providing full clear-ance into the cabinet. The hardware set is pre-assembled on to a track systemthat can be cut to fit for quick assembly and installation.- Door widths vary from 23 5/8” to 47 1/4” (600 to 1200 mm).For further technical details, please visit PRE-ASSEMBLED HARDWARE SETS INCLUDING TRACK FOR 2 DOORS CABINET WIDTHEKU-FRONTINO 20 H base system type S147 1/4” to 55 1/16” (1200 to 1399 mm)EKU-FRONTINO 20 H base system type S255 1/8” to 62 15/16” (1400 to 1599 mm)EKU-FRONTINO 20 H base system type S363” to 70 13/16” (1600 to 1799 mm)EKU-FRONTINO 20 H base system type S470 7/8” to 78 11/16” (1800 to 1999 mm)EKU-FRONTINO 20 H base system type S578 3/4” to 86 9/16” (2000 to 2199 mm)A-FIL NANOTOP MOUNT BOTTOM MOUNTA-FIL MEDIUMTOP MOUNT BOTTOM MOUNTA-FIL 2TOP MOUNT BOTTOM MOUNTA-FIL 3TOP MOUNT BOTTOM MOUNTHARDWARE SET FOR 2 DOORSSLIDER S20 system hardware set including trackHARDWARE SET FOR 2 DOORSSLIDER S20 system hardware set including trackEKU-FRONTINO 40 H FSHARDWARE SET FOR 2 DOORS DOOR WIDTHCABINET WIDTH 47 1/4” to 70 3/4”(1200 to 1799 mm)EKU-FRONTINO 40 H FS system hardware set type S23 5/8” to 35 3/8”(600 to 899 mm) REQUIRES THE FOLLOWING PRODUCTTrack set for two doorsHARDWARE SET FOR 2 DOORS DOOR WIDTHEKU-FRONTINO 40 H FS system hardware set type MSLIDER L70 - LARGESLIDER L70 - 3 DOORSCINETTO PS40.1 - 2 DOORSCINETTO PS40.1 - 3 DOORSHARDWARE SETS FOR 3 DOORSCCINETTO PS40.1 - 3 DOORS system hardware set for right-hand door (left-hand opening) CINETTO PS40.1 - 3 DOORS system hardware set for middle door (left-hand opening) CINETTO PS40.1 - 3 DOORS system hardware set for middle door (right-hand opening) CINETTO PS40.1 - 3 DOORS system hardware set for left-hand door (right-hand opening)STANDARD SLIDING DOOR HARDWAREDUCASSE AL 1535 WDHARDWARE SET FOR 1 DOORDUCASSE AL 1535 WD system hardware setREQUIRES THE FOLLOWING PRODUCTS RAIL LENGTHPHOTO MANQUANTE EKU-CLIPO 15 H ISEKU-CLIPO 15 H MSEKU-CLIPO 16 H ISHARDWARE SET FOR 2 DOORSEKU-CLIPO 16 H IS system hardware setEKU-CLIPO 16 HM ISHARDWARE SET FOR 2 DOORSEKU-CLIPO 16 HM IS system hardware setTRACKS AND ACCESSORIES RAIL LENGTHEKU-CLIPO 16 H FS HARDWARE SET FOR 1 DOOREKU-CLIPO 26 H ISHARDWARE SET FOR 2 DOORSEKU-CLIPO 26 H IS system hardware setREQUIRES THE FOLLOWING PRODUCTS RAIL LENGTHHARDWARE SET FOR 2 DOORSEKU-CLIPO 26 H MS system hardware setREQUIRES THE FOLLOWING PRODUCTS RAIL LENGTHEKU-CLIPO 36 H ISHARDWARE SET FOR 2 DOORSEKU-CLIPO 36 H IS system hardware setREQUIRES THE FOLLOWING PRODUCTS RAIL LENGTH Guide rail insert for the bottom of the door98” (2.5 m)EKU-CLIPO 36 HM ISHARDWARE SET FOR 2 DOORSEKU-CLIPO 36 HM IS system hardware setREQUIRES THE FOLLOWING PRODUCTS RAIL LENGTH Guide rail insert for the bottom of the door98” (2.5 m)EKU-REGAL A 25 H FSCINETTO PS10HARDWARE SETS FOR 1 DOORCINETTO PS10 system hardware set internalCINETTO PS10 system hardware set externalREQUIRES THE FOLLOWING PRODUCTS RAIL LENGTH Double Lower Guide Track10’ (3.05 m)CINETTO PS48HARDWARE SETS FOR 1 DOOR PRODUCT CINETTO PS48 hardware set internal door18948AP2E01 CINETTO PS48 hardware set external door for a thickness up to 3/4” (18 mm) 18948AP2E1801 CINETTO PS48 hardware set external door for a thickness up to 7/8” (23 mm) 18948AP2E230118948AP2E3301Glass WoodTRACK MOUNTING Surface - Outside the cabinetROLLER TYPEAxel(110 lb - 50 kg) ROLLER TYPEPremium ball bearing(176 lb - 80 kg)DOOR INSTALLATION Full overlayROLLER POSITIONUpperSOFT-CLOSEMECHANISMOne-way operation DOOR THICKNESS5/16’’(8 mm)DOOR THICKNESS11/16’’ to 1 1/16’’(19 to 28 mm)Reference: Options 1, 2, 3 Reference: Options 4, 5, 6DUCASSE AL 1535 GLEKU-CLIPO 16 GPK/GPPK ISH A R D W A R EEKU-CLIPO 36 GPK/GPPK ISGPKEKU-CLIPO 36 G ISHARDWARE SETS FOR 2 DOORSEKU-CLIPO 36 G IS system hardware setSoft-close mechanismREQUIRES THE FOLLOWING PRODUCTS RAIL LENGTHBI-FOLDING/BYP ASSING SLIDING CLOSET DOOR HARDWAREDUCASSE PL 2550HARDWARE SET 1 SINGLE BI-FOLDING DOORDUCASSE PL 2550 system hardware setREQUIRES ONE OF THE FOLLOWING PRODUCTS RAIL LENGTH Single upper running track78 3/4” (2 m) Single upper running track118” (3 m)。

120重型推拉门吊趟门、平开门 120红酸枝重型推拉门吊趟门 120金橡木推拉吊趟门平开门83料欧弧推拉门吊趟门 88钻石料推拉门、吊趟门、平开门 86料晶泳红酸枝平开门推拉门红酸枝推拉吊趟门平开门 80料拉丝金推拉吊趟门、平开门 86料晶泳红梨木平开门推拉门120铝合金重型推拉吊趟门 120镁铝合金重型推拉吊趟门十大品牌铝合金门窗铝合金门窗|断桥铝门窗|铝木复合门窗|隔音门窗|节能门窗|推拉门窗|平开门窗|折叠门|地弹簧门|悬窗|天窗|弧形窗|百叶门窗|纱门断桥铝门窗|高端别墅门窗|中空推拉门|移动铝合金门|阳台铝合金门|厨房铝合金门|室内落地门|双轨推拉门|落地铝合金门|防盗隔音门|断桥推拉门窗|卫生间门|铝型材双开门钛镁合金平开门|铝合金艺术门|铝合金豪华门|铝合金折叠门|铝合金对开门|铝合金重型推拉门|吊趟门|平开门|广东铝合金门|佛山铝门|名牌吊趟门|品牌折叠门|室内推拉门|推拉门哪家好|铝合金推拉门|玻璃隔断推拉门|断桥铝推拉门|推拉门最新报价|客厅隔断门十大品牌推拉门|浴室推拉门|卫生间推拉门|单扇推拉门|推拉门生产厂家|玻璃推拉门|推拉门尺寸|大型推拉门|室内推拉门|移动隔断墙|铝合金代理|重型推拉门品牌厂家铝合金2.0重型推拉门厂家|广东折叠门吊趟门厂家|佛山推拉门最新图片高端门窗品牌铝合金门批发商|重型推拉门供应商|折叠门供货商|推拉门品牌商| 开平门品牌厂家|十大名牌厂家铝合金门窗厂家行情|推拉门价格|折叠门窗效果图片|铝合金门窗价格走势铝合金门窗厂家|铝合金门窗最新报价广东铝合金门窗供应信息广东铝合金门窗批发代理推拉门品牌排名|推拉门设计与制造|高级推拉门|推拉门企业|带电动推拉门防盗推拉门|推拉门型号|新型推拉门|推拉门公司|银行推拉门推拉门装修|推拉门装饰|高端推拉门|隔断推拉门|浴室推拉门|百叶推拉门|书房推拉门|餐厅推拉门|三轨推拉门|拼格推拉门|铝合金钢化玻璃推拉门|十大品牌推拉门|水晶格条推拉门请致电:一八玖二七二七零零伍零佛山欧驰门窗系统有限公司新推33*80推拉窗,产品几个鲜明特色:1、产品采用壁厚1.4厚国标A棒铝材,铝型材强度、硬度均有保证;2、颜色可以选择电泳香槟、澳洲红木、黄花梨、白色,也可以根据客户需要自行定制双色,即室内采用原木木纹色,室外采用氟碳喷涂砂灰色、砂金色、砂银色等颜色,即可以满足住户室外小区统一要求,又可以满足住户室内个性化需求;3、五金配件采用全德国进口五金——-好博一字锁、执手、扣锁、地轮,使用轻盈;推拉时分贝时空之在18-20左右,静音门窗品质;4、结构合理,80推拉窗采用双高轨做法,高轨底部开启渗水漏水装置,排水性能优异;再配以金刚网,防蚊、防虫、放盗性能好;5、价格实惠,比起高端窗,80推拉窗价格更加实惠,市场接受程度高,便于经销商开启豪华别墅家装市场。

美式提拉窗滑轮式提拉器原理(一)美式提拉窗滑轮式提拉器1. 简介•什么是美式提拉窗滑轮式提拉器？•常见使用场景和功能介绍2. 滑轮原理•提拉器的滑轮构造和作用•滑轮的材质和结构设计3. 提拉器工作原理•滑轮与提拉绳的配合作用•通过提拉绳实现窗户开闭的机制4. 特点与优势•操纵简便，力度均匀•耐用性和稳定性较强•美式提拉窗滑轮式提拉器的独特优势5. 安装与维护•安装步骤和注意事项•维护保养和故障排除6. 适应范围与市场应用•美式提拉窗滑轮式提拉器的适用窗户类型•市场上常见的品牌和产品推荐7. 总结•美式提拉窗滑轮式提拉器的广泛应用前景•结束语美式提拉窗滑轮式提拉器1. 简介美式提拉窗滑轮式提拉器，是一种常见于美式窗户的开闭装置。

它采用了滑轮原理，通过提拉绳来实现窗户的开合。

这种提拉器广泛应用于住宅、办公室和商业场所等各种建筑中。

2. 滑轮原理滑轮是提拉器的核心部件，它通常由金属（如铝合金）或塑料制成。

滑轮上有槽和凹槽，可以将绳子固定在上面。

当绳子在滑轮上滚动时，滑轮会产生力的放大作用，使得更小的力能够控制窗户的开合。

3. 提拉器工作原理美式提拉窗滑轮式提拉器的工作原理很简单。

当我们拉动提拉器上的绳子，绳子会围绕滑轮转动，由于滑轮的放大作用，我们的拉力会传递给窗户上的开闭装置，从而实现窗户的开合。

4. 特点与优势美式提拉窗滑轮式提拉器有以下特点和优势：•操纵简便，只需要轻轻拉动绳子即可完成开窗或关窗的操作。

•力度均匀，滑轮的设计使得窗户开闭过程更加平稳，避免了窗户出现卡顿或猛烈震动的情况。

•耐用性和稳定性较强，滑轮和提拉绳采用耐用的材质制作，能够长时间使用而不易损坏或松动。

5. 安装与维护安装美式提拉窗滑轮式提拉器的步骤如下：1.确定安装位置，根据窗户的设计和尺寸选择合适的位置。

2.固定安装座，使用螺丝将座固定在窗户框上。

3.安装滑轮，将滑轮固定在安装座上。

4.调整提拉绳的长度，确保绳子能够顺利穿过滑轮并拉动窗户。

Product DescriptionThe CS Cavity Slider Pocket Door Systems are for sliding wood doors weighing up to 500 lb (227 kg) each and optional SofStop soft-close mechanisms for up to 264 lb (120 kg) per door. Made for standard 2 x 4 wood and metal wall stud construction.Choose from a selection of pocket frames for door widths from 24 in (610 mm) to 48 in (1219 mm) and door heights of up to 80 in (2030 mm) and 96 in (2438 mm)Ideal for residential, commercial, and institutional projects for a wide variety of applications. WEBKIT no.SofStop Yes/No Door Width Door Height WEBKIT1240082 200 lb (90 kg)No24 to 30 in (610 to 762 mm)80 in (2032 mm)WEBKIT1240138 500 lb (227 kg)No 37 to 42 in (914 to 1066 mm)96 in (2438 mm)WEBKIT1240081 176 lb (80 kg)Yes Twin 36 to 42 in (914 to 1066 mm)96 in (2438 mm)WEBKIT1240133 264 lb (120 kg)Yes Single34 to 48 in (864 to 1219 mm)96 in (2438 mm)-CarriSnap mounting suspension plate simple mounting and releasing the upper trolley without tools-Sturdy double wall aluminum pocket frame structure can be cut to size to accommodate different door widths and heights-Low profile upper track is part of the structure of the pocket frame-Trim clips for easy press-on mounting for door jamb trim-Pivoting bottom guide to ease loading the door into the pocket frame during installationPart no. DescriptionDKM0611M6 hardware set with 1 stop,200 lb(90 kg)DKM0811M8 hardware set with 1 stop,500 lb(227 kg)DKS0311Hardware set with single actionsoft close 176 lb(80 kg)DKS0411Hardware set with single actionsoft close 264 lb(120 kg)Part no. (frame only)。

Loading Weight(Per two 4-wheel hangings)*1100kg N10200kg N20400kgN40Meter ScrewmPowder Coating MunsellN7(Gray)Spot WeldingHow to install Sliding Door Track SystemEx. N20 Parts CombinationSide CoverWall BracketTrack fixing bracketDoor Catch Stopper (Bottom Set)Guide RollerGuide Roller(Bottom Set)Plate(For iron door)*For Wooden door is Apron4-WheelTop TrackDoor Catch Stopper Edge P art of Top Trrack *2T o p T r ac kSide CoverDoor Catch Stopper (Upper Set)Track Fixing BracketDoor Bottom Part (Example of installation)Bottom Guide Track with AnchorDoor Catch Stopper (Bottom Set)DoorDoorNewton 20 (Load Weight: 2000N(About 200kg ))●Increased Quietness and Easy open & close●Free of Hexavalent chromium processing (Friendly to environment)・Commercialize middle load capacity 200kg type between popular Steel Sliding Door Track #3 & #4・Realize High-durability and light weight by adopting a Hi-strength welded galvanized steel(Powder coating) on the Track.・Adopt a resin material on the outer circumference of wheel.New shape of track to prevent contact between wheel inside and track realizes quietness and smooth runnability.・Wheel gets load equally even if the door or hanging tools incline due to the wheel design that moves flexibly in all directions.Curve track(R600) is also available.(Applied to 4-wheel and 2-wheel)・Brackets are proceeded to avoid any scratch during installation work .・Two variations of 4-wheel and 2-wheel to hang door or tools.Loading capacity: 2000N(about 200kg) at two of 4-wheels per one door. Loading capacity: 1000N(about 100kg) at two of 4-wheels per one door.500N(about 50kg) at one trolley 2-wheel.Comparison date(House Test date)Door weight 1470N(150kg)Newton FeaturesOpening force 80% down *House test date on inside trackN20 ModelN20 4-WheelN20-4WSN 202-Wheel hanging ToolsN20-2TRN10 2-WheelN 20-2WS2•Materials: SPHC(Trivalent Chrome), Resin, etc.•Load capacity: up to 200N(about 200kg) by hanging 2 pcs per one door.•Adapt a ball bearing on the axle bearing.•Available for Curve Track(R600).*Don't use for other than N20 Track(N20 Curve Track).•Materials: SPHC(Trivalent Chrome), Resin, etc.•Load capacity: up to 1000N (about 100kg) by hanging 2 pcs per one door.•Adapt a ball bearing on the axle bearing.•Hanging bolt is replaceable.•Available for Curve Track(R600).*Don't use for other than N20 Track(N20 Curve Track).•Materials: SPHC(Trivalent Chrome), Resin, etc.•Load capacity: up to 500N (about 50kg) per one wheel.•Adapt a ball bearing on the axle bearing.•Available for Curve Track(R600).*Don't use for other than N20 Track(N20 Curve Track). *Not available for direct track mounting.*Not applied to N40 for Heavy doorCheck MovieIndustrial Sliding Door System Newton 20(N 20)N20Top TrackN20-HR N20 PlateN20-PLN20Bottom Guide Track with AnchorN20-NGRN20ApronN20-APN20Curve Top TrackN20-HR600RN20Guide RollerN20-GRON20Curve Guide Track with AnchorN20-HR600RN20Guide Roller with FrameN20-GRAP•Materials: SPHC(Trivalent Chrome, Musell N7)•Track Length: 2000, 3000mm•Materials: SS400(Trivalent Chrome)•Parts for connecting 4-wheel bolt and iron door.•Recommendable screw: M10•Materials: SGCC•Track Length: 2000, 3000mm •With Anchor on both sides•Materials: SPHC(Power coating, Munsell M7), etc•Parts for connecting 2 or 4-wheel bolt and wooden door.•Materials: SGH(Power coating, Munsell M7)•Standard R: R600(1/4 circle)•Cross-sectional shape is same with N20 Top Track •Available for made to order more than R600*Can't mount directly•Recommendable screw: M5•Materials: SPHC(Lacquer-finished, Munsell M7)•Standard R: R600(1/4 circle)•Cross-sectional shape is different from N20 Bottom Guide Track with Anchor.•Available for made to order more than R600.Materials: SPHC(Power coating, Munsell M7), Resin, etcN20Stopper with RubberN20-CSQN20Top Track Fix BracketN20-CSN20Door Stopper with DamperN20-DCSN20Track mounting Door StopperN20-RCSN20Door Stopper with CatchN20-KCSN20 Side CoverN20-SKN20Rubber Door Stopper N20-CSGIndustrial Sliding Door System Newton20(N20)•Materials: SPHC(Trivalent Chrome), Black rubber, etc •Use for stopping wheel drop out and door positioning.•In case of big impact to be expected, please hit the door on the vertical frame.•Use with Bottom Door Stopper (Separately).*Not available for Curve Top Track.•Materials: FCD450(Trivalent Chrome), SUS304 Rubber(Black), etc•1 set by Upper and bottom door stoppers•Please use this door stopper in case of bi-parting fitting.•Recommendable screw: M6*Not available for Curve Track.•Materials: SPCC(Power coating, Munsell M7)•Cover for blindfolding the edge of track.In case of stopping wheels, please use door stopper.*Can't use as Ceiling bracket.*Not available for Track direct mounting.•Material: Rubber(Black)•Door Stopper attached to vertical frame.•Recommendable screw: M5•Fix Top Track and Bracket(Ceiling and Wall) and prevent the gap.•In case of sopping door, please use door stopper.•Materials: FCD450(Trivalent Chrome), SUS304 Rubber(Black), etc•Used only the case of being able to use the upper stopper. •Damper gets the impact.•Push back about 30mm by repulsion.*Not available for Curve Track.Industrial Sliding Door System Newton20(N20)N20Ceiling Bracket (Single Channel)N20-OBN20Ceiling Bracket (Double Channel)N20-OB2N20Wall Bracket (Single Channel)N20-SB N20Wall Bracket(Double Channel)N20-SB2N20Ceiling BracketN20-BOXN20Joint Bracket for Ceiling (Single Channel)N20-OBTN20Joint Bracket for Ceiling (Double Channel)N20-OBTN20Joint Bracket for Wall (Single Channel)N20-SBTN20Joint Bracket for Wall (Double Channel)N20-SBT2N20Joint Ceiling BracketN20-TBOX•Materials: S S400(Power coating, Munsell M7), etc •Assembly bolts: M8•Recommendable screw: M8•Materials: S S400(Power coating, Munsell M7), etc •Use in Joint point between tracks.•With Track connection plate•Assembly bolts: M8•Recommendable screw: M8•Materials: S S400(Power coating, Munsell M7), etc •Assembly bolts: M8•Recommendable screw: M 10•Materials: S S400(Power coating, Munsell M7), etc •Use in Joint point between tracks.•With Track connection plate•Assembly bolts: M8•Recommendable screw: M 10•Materials: S S400(Power coating, Munsell M7), etc•The position of the mounting holes differs from Joint Bracket.•Recommendable screw: M8•Materials: S S400(Power coating, Munsell M7), etc •Use in Joint point between tracks.•With Track connection plate•The position of the mounting holes differs from Bracket.•Recommendable screw: M8•Materials: S S400(Power coating, Munsell M7), etc •Assembly bolts: M8•Recommendable screw: M8•Materials: S S400(Power coating, Munsell M7), etc •Use in Joint point between tracks.•With Track connection plate •Assembly bolts: M8•Recommendable screw: M 10•Materials: S S400(Power coating, Munsell M7), etc •Recommendable screw: M8*In case of using Side Cover, please use flat head of bolt less than 5.5mm•Materials: S S400(Power coating, Munsell M7), etc •Use in Joint point between tracks.•Recommendable screw: M8。

全新推拉门装置施工方案英文版New Sliding Door Installation PlanIntroductionThis document outlines the construction plan for a new sliding door system. The goal is to provide a straightforward guide for the installation process.Materials Needed- Sliding door kit- Tools (screwdriver, drill, level)- Screws and bolts- Measuring tapeStep-by-Step Installation Process1. Measure the door frame to ensure the sliding door fits properly.2. Install the track on the top of the door frame using the provided screws and bolts.3. Attach the rollers to the door panel, ensuring they are securely in place.4. Slide the door panel into the track and test its movement.5. Install the door handle according to the kit instructions.6. Adjust the door alignment if necessary by adjusting the rollers.7. Test the door multiple times to ensure smooth operation.Safety Considerations- Always wear protective gear when using power tools.- Use caution when handling heavy door panels.- Ensure the track is securely attached to the door frame to prevent accidents.ConclusionBy following this simple installation plan, you can successfully set up a new sliding door system in your space. Remember to take your time and follow each step carefully for the best results.。

推拉门原理与制作方法
推拉门是一种常见的开关门方式，它通过推拉方式来打开和关闭门体。

推拉门的制作方法主要包括选择门体材料、设计门体结构、制作门体和安装门轨等步骤。

1. 选择门体材料：推拉门的门体可以选择木材、铝合金、钢材等材料。

根据需要选择合适的材料，并保证门体的稳固性和安全性。

2. 设计门体结构：根据需要，确定推拉门的尺寸、形状和结构。

设计门体结构时要考虑到门的平稳推拉，避免卡阻和摩擦。

3. 制作门体：根据设计的门体结构制作门体。

如果选择木材为材料，可以使用锯木加工门板和门框。

如果选择铝合金或钢材，可以使用剪切、折弯等方法来制作门板和门框。

4. 安装门轨：安装门轨是推拉门制作的关键步骤。

根据门体结构的设计确定门轨的形状和尺寸，安装门轨需要保证其牢固性和平稳性。

5. 安装门体：将制作好的门体安装在门轨上。

确保门体与门轨的衔接紧密，能够顺利推拉。

6. 测试运行：安装完成后，进行推拉门的测试运行。

检查门体的推拉顺畅度、稳定性和安全性。

总结：推拉门的制作方法包括选择门体材料、设计门体结构、制作门体和安装门轨等步骤。

制作推拉门需要考虑材料的选择、门体结构的设计和制作，以及门轨的安装和门体的测试运行等环节。

滑动门技术滑动门技术是一种广泛应用于现代建筑的门窗技术，它以其出色的设计和便利的使用方式受到人们的喜爱。

滑动门技术的应用领域非常广泛，无论是家庭住宅、商业建筑还是公共场所，都可以看到它的身影。

下面我将从滑动门的定义、优点和应用等方面介绍这项技术。

滑动门是一种能够在轨道上滑动开启和关闭的门。

它由门框、玻璃和滑轨等组件构成。

滑动门的门框通常由铝合金、不锈钢等材料制成，具有轻量化、耐腐蚀等特点。

玻璃作为滑动门的主要材料，可以透明或半透明，让室内与室外的光线得以流通。

滑轨是滑动门的核心零件，通过其设计合理的滑动系统，门可以轻松地在轨道上滑动。

滑动门技术有着众多的优点。

首先，它节省空间。

相比传统的开启方式，滑动门不需要门的摆动空间，因此可以节省大量空间。

对于空间有限的场所，如小型房屋或商铺，使用滑动门能够更好地利用空间。

其次，滑动门具有方便实用的特点。

滑动门的开启和关闭非常轻松便捷，只需要轻推门体即可完成。

这也使得滑动门非常适合老年人、儿童和行动不便的人群使用。

此外，滑动门还具有良好的密封性能和隔音效果，可以有效隔离外界噪音和气温，提高室内的舒适度。

最后，滑动门的外观美观大方，可以增加建筑的整体美感。

滑动门技术在各个领域得到了广泛的应用。

在住宅建筑中，滑动门常被用作阳台门或者花园门，使得室内与室外的交流更加便利。

商业建筑中，滑动门被广泛运用于商场、酒店和办公楼等场所的大门和入口处。

滑动门的大面积玻璃设计不仅可以提供良好的采光效果，还可以吸引顾客的目光，增加商店的吸引力。

在公共场所，如机场、医院和学校等，滑动门也常见于大厅和走廊的出入口处，方便人流的进出，并提供良好的通风效果。

除了上述应用领域，滑动门技术还有一些创新的应用。

例如，一些高档住宅区或者办公楼在设计中采用了自动感应的滑动门。

利用红外线、声波或者光电设备等技术，滑动门可以自动感知到人员的来往，从而自动开启或关闭，提供更加便捷、高效的通行方式。

这种创新的应用进一步提升了滑动门技术的实用性和先进性。

十大高端移门品牌排行榜移门什么牌子好推拉门,也叫移门,除了能为衣柜、衣帽间提供密封防尘功能外,还可以用在厨房、阳台、卫生间等地,起到了很好的空间分隔以及增加私密性的作用。

但是不同品牌的智能锁在功能设计以及品质上有所不同，哪些移门是真正的群众使用后的口碑产品，高端营销推广平台鹿豹座为大家来盘点一下。

1、顶固Topstrong广东顶固集创家居股份(原中山市顶固金属制品)，五金配件十大品牌，移门十大品牌，时尚门-生态门十大品牌，国家保护商标，广东省著名商标，广东省名牌，广东省高新技术企业，广东省民营科技企业，专业与时尚并重的装饰建材家居领导品牌2、索菲亚SOGAL索菲亚家居股份(原广州市宁基装饰实业股份)，整体衣柜十大品牌，十大书柜/移门品牌，衣柜顶级专家，消费者最喜爱品牌，全国工商联家具装饰业商会衣柜专业委员会会长单位，华南地区最具影响力建材品牌，定制衣柜行业内首家上市公司。

3、科嘉豪门江苏省南京圣沁源贸易，中国十大滑动门-推拉门-移门品牌，源自美国的高端品牌，推拉门-移门产业璀璨明星，中国绿色建材产品，其产品业界具有较高信誉度和知名度，以领先技术水平、独特的设计风格和品位在享誉于业界，集专业策划、研发、生产、销售为一体的多功能大型门业厂商4、拉迷Lami加拿大拉迷国际集团，上海拉迷家具，滑动门-推拉门-移门十大品牌，整体衣柜十大品牌，上海知名品牌，源自加拿大著名品牌，采用行业最高装配工艺标准制造，中国绿色认证产品，以其卓越的品质/精湛的工艺而闻名的门业企业5、普吉尼杭州普吉尼家居用品，推拉门-移门十大品牌，时尚门十大品牌，中国知名橱柜品牌，产品设计秉承意大利简约时尚的设计风格，致力打造全球家居市场知名品牌，国内知名橱柜-滑动门-整体衣柜生产商。

6、好莱客Holike广州好莱客创意家居股份，整体衣柜十大品牌，移门十大品牌，行业领军品牌之一，华南杰出家居建材品牌，广东省著名商标，广州市著名商标，消费者最喜爱品牌，华南最具影响力家居品牌，高新技术企业，致力于整体衣柜领域发展的行业著名企业7、史丹利STANLEY品谱五金家居(深圳)，史丹利，滑动门-推拉门-移门十大品牌，知名(著名)衣柜-整体衣柜品牌，1843年创立于美国，百年经典旗舰工具、安防系统和家居品牌，中国整体家居联盟主席单位8、蓝凯Lanka蓝凯门窗科技(香港)，移门十大品牌，源自香港的高端移门品牌，中空门、移门行业内的新星，行业著名品牌，安徽省极具规模的专业门窗生产企业，中国绿色建材产品，以领先的产品品质、生产技术、设计灵感享誉业内门窗专家，专做门窗!9、班尔奇Pauchie班尔奇家具(上海)，移门十大品牌，中国知名(著名)衣柜-整体衣柜品牌，上海装饰材料市场畅销品牌，上海装饰材料市场竞争力品牌，行业中公认的旗舰企业之一，由香港科曼多国际投资的外商独资企业10、瑞丽宜家瑞丽宜家家居，整体衣柜十大品牌，移门十大品牌，行业著名品牌，中国衣柜委员会常务理事，安徽省家居行业领航企业，大型定制类家居产品制造服务商，消费者最信赖家居品牌，全屋定制家居领导品牌。

专利名称：一种具有自动清洁功能的门窗推拉装置专利类型：实用新型专利
发明人：倪华
申请号：CN202121844892.5
申请日：20210809
公开号：CN215804251U
公开日：
20220211
专利内容由知识产权出版社提供
摘要：本实用新型公开了一种具有自动清洁功能的门窗推拉装置，包括外框，其特征在于：所述外框的中心处轴承连接有内框，所述内框的中心固定安装有玻璃，所述外框的内部顶端固定安装有固定柱，所述固定柱的下端焊接有第一锥齿轮，所述固定柱贯穿外框底部，所述固定柱贯穿内框的顶部，所述内框的内部右侧轴承连接有第二锥齿轮，所述第一锥齿轮与第二锥齿轮为啮合连接，所述第二锥齿轮的左侧焊接有丝杆，所述丝杆与内框为轴承连接，所述丝杆的右侧螺纹啮合有底座，所述底座的下方焊接有清洁杆，所述清洁杆的下端固定安装有清洁刷，所述清洁刷与玻璃表面相接触，本实用新型，具有实用性强和自动清洁的特点。

申请人：沭阳劲豪门窗有限公司
地址：223600 江苏省宿迁市沭阳县百盟建材城D区6#D6-112号房
国籍：CN
代理机构：北京广溢知识产权代理有限公司
代理人：张启炎
更多信息请下载全文后查看。

适合DIY的精确靠山靠山基本完成，稍加改进也可以用于雕刻机（方案不全是原创，原理借鉴了一点国外的东西）。

这几天使用起来很爽。

优点是方便准确，只要滑杆足够长可调距离很大，结构简单重量轻、便于拆卸，整个台锯可以用普通轿车运走。

还有很多地方需要完善，怕ipolo等不及要看，现在就上传了说是“精确”，也许专业技术人员认为我达不到，受我个人条件所限，但误差小于是没问题的：M10螺杆螺距，微调做成6角形，每调1面即，当然还可以更精细地调节，用眼睛看有困难了。

至少在原理上是精确的，只是个概念型。

真的希望有专业工厂采纳这个方案，用全金属当然比我的要好得多。

Diy这个最关键的就是——处处准确、准确、再准确。

需要一点点技术与技巧，各位DX一定不必我差，多提意见啊。

不管哪位愿意采用这个方案，只要在这里顶一下，谢谢fence全景.滑块定位卡324.定位卡325定位卡326微调01微调02微调03任意位置调零-01任意位置调零-02做的太牛了. 请教一些细节问题.1.图中 1 处的靠山用的是一个推拉门吊门导轨, 这个靠山跟后面的调节移动的那个螺纹是如何连接的2. 锁紧靠山如何实现是否就是后面的一个夹具的头压紧螺纹两边的导轨处有无锁紧机构.另外下图 2处的导轨的滑块怎么加工或者哪里买到的另外导轨是钢管还是实心的.3. 图中3处的细节解释. 看一个大概意思. 就是调节图3机构, 可以移动靠山. 调好后, 用那个红把的夹子夹紧. 除此外, 还需要其他夹紧措施吗4. 图中4处,两个支架之间的水平如何实现安装两个导轨的时候, 如果找平多谢wenti今天拆了照了几张，便于大家看记得滑块和杆是河南产，都在潮龙买的一共2百多。

杆是16mm实心不到60元/米，滑块20/个，固定夹头10/个。

这家的东西还比较精密（店家介绍400/米的轨道可以精确到零点零零……几mm，我说：我买，买，买不起），我做成以后可以纹丝不动，滑块后面的夹头是为了保护，用大力量时靠紧滑块固定以免把那个推拉门轨道弄弯，只是担心而已，一般没用。

Floor-Concealed Door Closers BTS80• yes- noMaximum door widths and recommended sizes shown are for average conditions. If there are unusual site conditions, e.g.high or exceptionally heavy doors or wind pressure, the next stronger spring size should be selected.The BTS80 Series of floor-concealed door closers offer adaptability to almost any installation.The closer’s compact body permits its use where a larger closer would be prohibitive. Versatility allows installation in thin slab concrete subfloor construction. A wide selection ofinterchangeable spindles makes the BTS80 suitable for virtually any floor covering or threshold application. Because the BTS80can control exceptionally heavy single- and double-acting doors,you can incorporate the floor closer into almost any design to meet most materials, size, and weight requirements.Trouble-free performance under adverse climatic and traffic conditions makes the BTS80 floor-concealed closerdependable and a perfect choice for even the most rigorous applications. For total control and uncompromising creativity for any door opening, specify a BTS80 floor-concealed closer.Dependable and Versatile Floor-Concealed CloserCertification:The DORMA BTS80 F Series is listed by U.L. and C.U.L. under their continuing reinspection programs. The DORMA BTS80 Series is certified to the requirements of ANSI/BHMA A156.4 for grade 1 closers.Specifications:All floor-concealed door closers shall be DORMA BTS80 Series employing a cam and roller mechanism. The closers shall be capable of controlling interior or exterior doors weighing up to 660 pounds and measuring up to 4'-0" wide exterior and 4'-6" interior. The closers will have selectable multipoint hold open between approximately 75º and 175º. The closers will have selectable delayed action to allow delayed closing from 175º to 75º. The closers will have mechanical backcheck at approximately 70º. Dual valve adjustment will provide controlled closing speed from approximately 175º opening range, even in cold temperature conditions. The closer will provide adjustment within the cement case to allow lateral and longitudinal adjustment of 1/4" and vertical height adjustment of 5/32". Field interchangeable spindles will be available to provide bottom door clearances ranging from 5/16" to 2-5/16".Optional Specifications:The closers should be used with sealing compound SC-1 to prevent water or cleaning solvent from entering the cement case.Floor-concealed door closers for all fire doors shall be DORMA BTS80 F. The closers shall be single-acting and have controlled closing from a full 180º. A sweep range of 180º–0º and latch range of 7º–0º will help insure positive latching of the door.Finishes:Optional Plated Finishes:Brass: 605 (Bright)or 606 (Satin).Bronze: 611 (Bright), 612 (Satin), or613 (Oxidized Satin Oil Rubbed).Nickel: 618 (Bright)or 619 (Satin).Chrome: 625 (Bright)or 626 (Satin).Standard Sprayed Finishes:Aluminum: 689.Bronze: 691 (Dull), 690 (Statuary), or 695 (Dark Duranodic). Gold: 696.Black: 693.Optional DORMA Custom Color or Designer Color Finishes: Contact Customer Service.Warranty: 25 years for projects within the United States. For full details, refer to the Limited Warranty Policy in the current DORMA price list.BTS80 Series Technical Details:•Compact closer body and cement case 2-3/8" deep suited for thin slab concrete construction.•Accommodates doors weighing up to 660 pounds and 4'-6"wide interior and 4'-0" exterior.•Closer adjustment in cement case provides lateral andlongitudinal adjustment of 1/4" and height adjustment of 5/32".• A pressure relief valve protects closer from damage caused by forced closing.•Optional sealing compound SC-1 prevents water or cleaning solvent from entering the cement case.•If door hardware or adjacent structures interfere with maximum opening, an auxiliary stop should be installed.BTS80Technical Details:•Closer body is non-handed.•Mechanical backcheck at approximately 70º (excluding size 3, where backcheck is removed to meet barrier-free through 90° of opening for easier passage).•Selectable delayed action between 175º and 75º. Extends the closing cycle to allow unobstructed passage.•Delayed action is functional when hold open is not engaged. •Dual thermostatic control valves combined with special hydraulic fluid provide controlled closing from 175º.•Selectable multipoint hold open between approximately 75ºand 175º.•Adjustment for start of hold open range or when delayed action releases. Adjustable between 75º and 105º.BTS80 FTechnical Details:••Closer body is handed.•Non-hold open only.•Mechanical backcheck at approximately 70º.•Dual thermostatic control valves combined with special hydraulic fluid provide controlled closing from 180º.•Recommended for applications using a wall magnet to holda door open at 180º.Accessory packages for the following applications are designated with an alpha suffix, i.e. “A,” “B.” For application details and accessory illustrations, see BTS Applications and Accessories brochure.ApplicationsDORMA Americas DORMA Architectural Hardware DORMA Drive, Drawer AC Reamstown, PA 17567-0411Telephone: (800) 523-8483Facsimile: (800) 274-9724E-mail:********************DORMA Glas1520 Jabez Run, Suite 303Millersville, MD 21108Telephone: (800) 451-0649Facsimile: (410) 923-3060E-mail:******************DORMA Canada1680Courtney Park Drive,Unit 13Mississauga, Ontario L5T 1R4Telephone: (800) 387-4938Facsimile: (905) 670-5850E-mail:*********************G H I J Inches 4-1/814-3/322-9/323/32Millimeters105358582Extended Spindle Insert NOTE: Closer and arm must be installed per template for door clearances shown to be valid.Closers with extended spindle inserts are used with thresh-olds, carpeted floors, or orterrazzo pans or in cases where more clearance between door and floor is required. All spindles are zinc plated.Pre-load SpindlesSpindles are available with a 3º pre-load for additional pressure to hold door in the closed position. Normally,this is only necessary for center-pivoted single acting applications. How-ever, they can also be used with other applications to compensate for templating errors. Specify hand of pre-load spindle when ordering.Universal cover plate 7410, suitable for left hand/right hand, 3/4"offset, 1-1/2" offset, and center pivoted doors. Material is stainless steel or brass depending on the plated finish specified.Cover PlateDORMA Mexico, S. de R.L. de C.V.Astrónomos 28, Col. Escandón México, D.F . 11800Del. Miguel HidalgoTelephone: (52+55) 5272-6937Facsimile: (52+55) 5272-6948E-mail:*******************.mx。

钛镁合金推拉门一、定义：钛镁合金推拉门具有强度高而密度又小,机械性能好,韧性和抗蚀性能很好.另外:钛合金推拉门的工艺性能差,切削加工困难. 在热加工中,非常容易吸收氢氧氮碳等杂质.还有抗磨性差,生产工艺复杂. 其主要成份是钛,但镁的含量也很多。

二、品牌：钛镁合金推拉门企业主要集中于广东、安徽、北京、上海、四大区域，这几大区域在设计、生产、服务、管理等方面引领着国内整体衣柜行业前进。

随着钛镁合金推拉门行业的发展，近年市场上出现了钛镁合金推拉门品牌：瑞丽宜家、欧派、顶固、索菲亚、好莱客、百特斯、西雅、利马衣柜、合生雅居、德尔曼、维尔斯、豪世家、美世、伊百丽、伊莎贝拉、科莱诺、玖拾度90°、红人衣柜、风鸟、多尔贝、德夫曼、名贵、富禄、百琪、新标、威斯蒂尼、博克曼衣柜、月兔、扬子等知名的专业整体衣柜企业。

三、钛镁合金推拉门十大品牌：1、钛镁合金推拉门之瑞丽宜家RILAJOY瑞丽宜家家居有限公司，中国钛镁合金推拉门品牌最丰富企业之一，移门衣柜行业著名品牌，知名钛镁合金推拉门品牌，中国著名商标，中国绿色环保产品，质量、服务、信誉AAA企业，专业从事定制类家居产品研发和生产的知名企业。

瑞丽宜家被广大的消费者们授予爱称“大众情人”，以其时尚健康产品形象和出色的营销方案荣获2012年移门品牌最具影响力奖、最佳终端服务品牌、2013年钛镁合金推拉门十大品牌称号。

2、钛镁合金推拉门之索菲亚SOGAL索菲亚家居股份有限公司（原广州市宁基装饰实业有限公司），整体衣柜十大品牌，十大书柜/钛镁合金推拉门品牌，衣柜顶级专家，消费者最喜爱品牌，全国工商联家具装饰业商会衣柜专业委员会会长单位，华南地区最具影响力建材品牌，定制衣柜行业内首家上市公司。

3、钛镁合金推拉门之好莱客Holike广州好莱客创意家居股份有限公司，整体衣柜十大品牌，钛镁合金推拉门十大品牌，行业领军品牌之一，华南杰出家居品牌，广东省著名商标，广州市著名商标，消费者最喜爱品牌，华南最具影响力家居品牌，高新技术企业，致力于整体衣柜领域发展的行业著名企业。