MS3-C板使用说明
- 格式：pdf
- 大小：281.39 KB
- 文档页数：9
MS3- C 电路板使用说明概述：MS3-C 电路板是通用标准型层站控制板，体积小巧，集成了点阵式显示器和具有自动寻址功能的CAN 总线。
具有低功耗、结构紧凑、抗干扰能力强等特点。
以下为MS3-C 的外观图及接口说明：（顶层）(底层)CANFIRE SFOUT UP ↑DOWN ↓ZSE INBOLTPWRARROW JCANPWR接口（3.96mm间距）:这是电路板DC24V工作电源接口:1 -- 0V2 -- +24VCAN接口（2.54mm 间距）:这是CAN-BUS总线接口:1 -- 自学习输入（低电平有效）2 -- 自学习输出（低电平有效）3 -- 串行数据CAN-L4 -- 串行数据CAN-HARROW接口（2.54mm 间距）:这是到站钟输出接口:1 -- 上行箭头/上行到站信号2 -- +24V3 -- +24V4 -- 下行箭头/下行到站信号SFOUT接口（2.54mm 间距）:这是“特殊运行”或“编程输出”接口：1 -- 特殊运行输出信号2 -- +24V3 -- +24V4 -- 编程输出信号UP接口（2.54mm 间距）:这是上行召唤按钮接口:1 -- +24V2 --上行召唤按钮LED3 -- 上行召唤开关信号4 -- GNDDOWN接口（2.54mm 间距）:这是下行召唤按钮接口:1 -- +24V2 --下行召唤按钮LED3 --下行召唤开关信号4 -- GNDFIRE接口（2.54mm 间距）:这是消防开关输入接口:1 -- GND2 -- 消防开关信号ZSE接口（2.54mm 间距）:这是ZSE开关输入接口:1 -- GND2 -- ZSE开关信号IN 接口（2.54mm 间距）:这是空置输入接口:1 -- GND2 -- 输入信号（低电平有效）BOLT 接口（2.54mm 间距）:这是厅门门锁检测输入接口*:1 -- GND2 -- 门锁信号（低电平有效）*检测220VAC 安全回路需要增加另一块叫EFCBolt 的电路板，它安装在每层的层门接线盒内。
EFCBolt 电路板(尺寸 90mm x 30mm):JCAN 跳线:如果插入短接桥，则有120Ω的电阻跨接在CAN-L 和CAN-H 上作为CAN-BUS 总线的终端电阻（通常在CAN-BUS 总线的最后一块MS3-C 板需要插入短接桥）。
JIN 跳线:这是用作选择“IN ”的输入信号（如VIP 服务）。
如果短接1-2脚：IN 接口用作空置输入信号。
如果跳线接在这个位置上并且“IN ”输入信号有效时，则编程输出信号（SFOUT 接口的第4脚）有效。
如果短接2-3脚： IN 接口用作VIP 输入信号（特殊运行）。
如果跳线接在这个位置上并且“IN ”输入信号有效时，则特殊运行输出信号（SFOUT 接口的第1脚）有效。
DIP 开关: DIP 开关1:此DIP 开关仅用作MS3-C 电路板的测试。
DIP 开关2和3:此两位DIP 开关用作选择箭头显示模式。
2--OFF, 3--OFF 静态箭头 2--ON, 3--OFF 滚动箭头 2--OFF, 3--ON 移动箭头 2--ON, 3--ON 闪烁箭头滚动和移动箭头：按电梯的运行方向移动。
MS3-C BOLTAC 220VDIP开关4和5:此两位DIP开关用作选择层位显示模式。
4--OFF, 5--OFF 静态层位4--ON, 5--OFF 滚动层位4--OFF, 5--ON 移动层位4--ON, 5--ON MS3-C自检滚动和移动层位：按电梯的运行方向移动。
MS3-C SpecificationGeneral ：The MS3-C was developed to be a widely useable standard floor control board with small size, an integrated indicator and CAN bus link with automatic addressing capability. It has lower power consumption, compact structure, high anti-jamming ability.The following shows the MS3-C operational elements ：（Top Layer ）(Bottom Layer)CANFIRE SFOUT UP ↑DOWN ↓ZSE INBOLTPWRARROW JCANPWR Connector（3.96mm pitch）:This is the 24V DC power supply terminal for the MS3-C:1 -- 0V2 -- +24VCAN Connector（2.54mm pitch）:This is the CAN bus terminal:1 -- TEACH IN input (low active)2 -- TEACH IN output (low active)3 -- CAN-L serial data4 -- CAN-H serial dataARROW Connector（2.54mm pitch）:This is the arrival gong output terminal:1 -- UP arrow/UP gong output GND signal2 -- +24V3 -- +24V4 -- DOWN arrow/DOWN gong output GND signalSFOUT Connector（2.54mm pitch）:This is the “Special Run” and “Free Output” terminal：1 -- Special Run output signal2 -- +24V3 -- +24V4 -- Free Output signalUP Connector（2.54mm pitch）:This is the UP call pushbutton terminal:1 -- +24V2 -- Call Acceptance UP LED (low active)3 -- Call signal UP (low active)4 -- GNDDOWN Connector（2.54mm pitch）:This is the DOWN call pushbutton terminal: 1 -- +24V2 -- Call Acceptance DOWN LED (low active)3 -- Call signal UP (low active)4 -- GNDFIRE Connector （2.54mm pitch ）: This is the fire service input terminal: 1 -- GND2 -- FIRE signal(low active)ZSE Connector （2.54mm pitch ）: This is the ZSE input terminal: 1 -- GND2 -- ZSE signal (low active)IN Connector （2.54mm pitch ）: This is a free useable input terminal: 1 -- GND2 -- Input signal (low active)BOLT Connector （2.54mm pitch ）:This is the BOLT input terminal used to monitor the landing door lock*: 1 -- GND2 -- Input signal (low active)*To monitor the 220VAC safety circuit, the additional safety PCB names EFCBolt must be installed in the wire distribution box of each landing.EFCBolt (dimension: 90mm x 30mm):MS3-C BOLTAC 220VJCAN Jumper:If this jumper is plugged in, 120Ω are connected serial to CAN-L and CAN-H to terminate the CAN bus line. (Normally this shall be done at the last MS3-C board in the CAN bus line)JIN Jumper:With this jumper, the function of the “IN” signal can be selected.Pos. 1-2: if the jumper is in this position and the connector “IN” is active, then the Free output signal of connector SFOUT (pin 4) is also active.Pos. 2-3: if the jumper is in this position and the connector “IN” is active, then the “Special RUN“ output signal of the connector SFOUT (pin 1) is also active.DIP Switches:DIP switch 1:This DIP switch only used for MS3-C testing.DIP switches 2 and 3:With these 2 DIP switches, the “ARROW mode” can be selected.2--OFF, 3--OFF static arrow2--ON, 3--OFF rolling arrow2--OFF, 3--ON moving arrow2--ON, 3--ON flashing arrowRolling and moving ARROW: the ARROW is moving in the elevator running direction.DIP switches 4 and 5:With these 2 DIP switches, the “Symbol mode” can be selected.4--OFF, 5--OFF static symbol4--ON, 5--OFF rolling symbol4--OFF, 5--ON moving symbol4--ON, 5--ON MS3-Cself-testRolling and moving symbol: the symbol is moving in the elevator running direction.。
