2017款东风本田思域维修手册-半轴

思域维修手册01一般性介绍一、引言欢迎使用思域维修手册！本手册旨在为维修人员提供关于思域汽车维护和修复的详尽信息。

本手册将介绍思域汽车的一般性介绍，包括车型概述、技术参数和重要组成部分。

二、车型概述2.1 车辆型号- 2.1.1 思域车型A- 2.1.2 思域车型B- 2.1.3 思域车型C2.2 车辆用途思域汽车适用于各种道路条件和不同环境的使用，包括城市道路、高速公路和乡村道路等。

2.3 适用地区思域汽车销售和使用范围涵盖了全球多个地区，本手册主要侧重于适用于该地区的版本。

2.4 技术特点思域汽车具有先进的技术特点，如燃油效率、安全性能和智能化驾驶辅助系统。

三、技术参数3.1 发动机参数- 3.1.1 排量- 3.1.2 最大功率- 3.1.3 最大扭矩3.2 车身参数- 3.2.1 车身尺寸- 3.2.2 座位容量- 3.2.3 行李厢容量3.3 燃油参数- 3.3.1 燃油类型- 3.3.2 平均油耗- 3.3.3 燃油箱容量四、重要组成部分4.1 发动机系统- 4.1.1 点火系统- 4.1.2 燃油系统- 4.1.3 冷却系统4.2 传动系统- 4.2.1 变速器- 4.2.2 离合器4.3 刹车系统- 4.3.1 刹车盘- 4.3.2 刹车片- 4.3.3 刹车液5：电气系统- 4.4.1 电池- 4.4.2 灯光系统- 4.4.3 指示器和仪表板六、附件本文档附带以下附件：1：思域汽车技术图纸2：思域汽车零部件清单3：思域汽车维修工具目录七、法律名词及注释---- 名词 ---- 注释 -------- ---- ---- ---- -------- 汽车厂商责任 ---- 汽车制造商对产品质量和安全的法律责任 -------- 保修期 ---- 汽车制造商承诺对车辆提供免费维修的期限-------- 保修范围 ---- 在保修期内，制造商承诺对特定故障提供免费维修 -------- 消费者权益 ---- 消费者在购买和使用汽车时的合法权益----。

进气系统节气门体的拆解/重新组装О形密封圈更换EVAP活性炭罐净化阀11-312催化转换器系统；11-313DTC 故障处理DTC P0420：催化系统效率低于门限值说明：• 进行故障处理之前，先记录冻结故障数据以及所有仪表快摄数据，再查阅一般故障处理说明(见11-3页)。

• 如果下列DTC 与DTC P0420同时存储，则应首先排除下列DTC 故障，然后再次检查DTCP0420。

P0137，P0138：副HO 2S(传感器2)P0141：副HO 2S(传感器2)加热器• 使用劣质燃油可使故障诊断代码DTC 的出现。

1. 打开点火开关至ON(II)。

2. 使用HDS 清除DTC 。

3. 起动发动机，在无负荷的情况下(位于驻车位置或空档)使发动机转速保持在3,000rpm(min -1)，直至散热器风扇运行，然后使其怠速运转。

4. 在下列条件下试驾：• 发动机冷却液温度高于70o C(158o F)• A/T 位于D 档位置(M/T 位于第5档)• 使用巡航控制时，保持车速为72-120km/h(45-75mph)约5分钟或更久。

• 不使用巡航控制时，保持车速为88km/h(55mph) 5分钟或更久。

5. 使用HDS 在DTC 菜单中监测DTC P0420的OBD 状态(OBD STATUS)屏幕是否显示执行(EXECUTING)？是－进行第6步。

否－进行第4步并重新检查。

6. 保持驾驶状态直至出现结果。

7. 使用HDS 在DTC 菜单中监测DTC P0420的OBD 状态(OBD STATUS) 屏幕是否显示未通过(FAILED)？ 是－进行第8步。

否－如果屏幕显示通过(PASSED)，间歇性故障，此时系统正常。

如果屏幕显示执行(EXECUTING)，保持驾驶状态直至出现结果。

如果屏幕显示不符合条件(OUT OF CONDITION)，进行第4步，然后重新检查。

8. 关闭点火开关。

9. 更换TWC(见11-315页)。

All service items not detailed in this section should be performed by a Honda technician or other qualified mechanic.To eliminate potential hazards,read the instructions before you begin,and make sure you have the tools and skills required.Make sure your vehicle is parked on level ground,the parking brake is set,and the engine is off.To clean parts,use a commercially available degreaser or parts cleaner,not gasoline.To reduce the possibility of fire or explosion,keep cigarettes,sparks,and flames away from the battery and all fuel-related parts.Let the engine and exhaust system cool before touching any parts.Do not run the engine unless instructed to do so.Be sure there is adequate ventilation whenever you operate the engine.Maintenance SafetyImportant Safety Precautions Potential Vehicle HazardsBurns from hot parts.Injury from moving parts.Carbon Monoxide poison from engine exhaust.164Some of the most important safety precautions are given here.However,we cannot warn you of everyconceivable hazard that can arise in performing maintenance.Only you can decide whether or not you should perform a given task.Service your vehicle according to the time and mileage periods on one of the Maintenance Schedules on the following pages.Follow theMaintenance Schedule for Severe Conditions if you drive your vehicle MAINLY under one or more of the following conditions.Driving less than 5miles (8km)per trip or,in freezingtemperatures,driving less than 10miles (16km)per trip.Driving in extremely hot [over 90°F (32°C)]ed primarily as a delivery vehicle or taxi that is drivenmostly in stop-and-go traffic and/or parked with the engine idling.Maintenance Safety,Maintenance ScheduleU.S.Owners Which Schedule to Follow:165Trailer towing,driving with a roof top carrier,or driving in mountainous conditions.Driving on muddy,dusty,or de-iced roads.Follow the Maintenance Schedule for Severe Conditions.Your authorized Honda dealer knows your vehicle best and can provide competent,efficient service.However,service at a dealer is not mandatory to keep your warranties in effect.Maintenance may be done by any qualified service facility or skilled person to keep all the receipts as proof of completion,and have the person who does the work fill out the Maintenance Record.Check your warranty booklet for more information.We recommend the use of Honda parts and fluids whenever you have maintenance done.If you only OCCASIONALLY drive under ‘‘severe’’conditions,you should follow the Maintenance Schedule for Normal Conditions.According to state and federal regulations,failure to perform maintenance on the items marked with will not void your emissions warranties.However,Hondarecommends that all maintenance services be performed at the recommended time or mileageperiod to ensure long-term reliability.U.S.Vehicles:Maintenance ScheduleCanadian Owners Servicing Your VehicleMaintenance,replacement,or repair of emissions controldevices and systems may be done by any automotive repairestablishment or individual using parts that are ‘‘certified’’to EPA standards.166NOTE:You should check the following items at the specified intervals.If you are unsure of how to perform any check,turn to the appropriate page listed.Tires Check the tire pressure monthly.Examine the tread for wear and foreign objects.See page .Lights Check the operation of the headlights,parking lights,taillights,high-mount brake light,turn signals,brake lights,and license plate light monthly.See page .183190Maintenance ScheduleOwner’s Maintenance Checks167Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule on the next page do not apply.NOTE:If you only OCCASIONALLY drive under ‘‘severe’’conditions,you should follow the Normal Conditions Maintenance Schedule.168See information on maintenance and emission warranty on page .:166Schedule if you drive your vehicle MAINLY under one or more of the following conditions:Extensive idling or long periods of stop and go driving,such as a taxi or a delivery vehicle.Driving less than 5miles (8km)per trip or,in freezing temperatures,driving less than 10miles (16km)per trip.Driving in extremely hot [over 90°F (32°C)]conditions.Follow the Maintenance Schedule for Severe Conditions.Driving on muddy,dusty,or de-iced roads.Trailer towing,driving with a roof rack,or driving in mountainous conditions.commercial Canadian Owners 169Replace at 60,000miles (96,000km)or 3years,then every 30,000miles (48,000km)or 2years.See dust and pollen filter on page for replacement information under special driving conditions.Use normal schedule except in dusty condition.See information on maintenance and emission warranty on page .1:2::1883:166Maintenance Schedule for Severe Conditions(for Normal and Severe Schedules)Maintenance Record 1705,000mi 10,000mi 15,000mi 20,000mi 25,000mi 30,000mi 35,000mi 40,000mi 45,000mi 50,000mi 55,000mi 60,000mi 65,000mi 70,000mi 75,000mi 80,000mi Signature or dealer stampmi/km Date mi/km Date mi/km Date mi/km Date mi/km Date mi/km Date mi/km Date mi/km DateSignature or dealer stampmi/km Date mi/km Date mi/km Date mi/km Date mi/km Date mi/km Date mi/km Date mi/km DateYou or the servicing dealer can record all completed maintenance here,whether you follow the schedule for normal conditions (page )or severe conditions (page ).Keep the receipts for all work done on your vehicle.8,000km 16,000km 24,000km 32,000km (or 1year)40,000km 48,000km 56,000km 64,000km (or 2years)72,000km 80,000km 88,000km 96,000km (or 3years)104,000km 112,000km 120,000km 128,000km (or 4years)168169(for Normal and Severe Schedules)Maintenance Record 17185,000mi 90,000mi 95,000mi 100,000mi 105,000mi 110,000mi 115,000mi 120,000mi 125,000mi 130,000mi 135,000mi 140,000mi 145,000mi 150,000mi 155,000mi 160,000mi Signature or dealer stampmi/km Date mi/km Date mi/km Date mi/km Date mi/km Date mi/km Date mi/km Date mi/km DateSignature or dealer stampmi/km Date mi/km Date mi/km Date mi/km Date mi/km Date mi/km Date mi/km Date mi/km Date136,000km 144,000km 152,000km 160,000km (or 5years)168,000km 176,000km 184,000km 192,000km (or 6years)200,000km 208,000km 216,000km 224,000km (or 7years)232,000km 240,000km 248,000km 256,000km (or 8years)Fluid Locations172Unscrew and remove the engine oil fill cap on top of the valve cover.Pour in the oil slowly and carefully so you do not spill.Clean up any spills immediately.Spilled oil coulddamage components in the engine compartment.Install the engine oil fill cap and tighten it securely.Wait a few minutes and recheck the oil level.Do not fill above the upper mark;you could damage the engine.Honda Motor Oil is the preferred 5W-20lubricant for your vehicle.It is highly recommended that you use Honda Motor Oil in your vehicle for optimum engine protection.Make sure the API Certification Seal says ‘‘For Gasoline Engines’’.The oil viscosity or weight is provided on the container’s label.5W-20oil is formulated for year-round protection of your Honda to improve cold weather starting and fuel economy.Adding Engine OilAdding Engine Oil173You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil:it displays the API Certification Seal and it is the proper weight.You must follow the oil and filter change intervals given on the maintenance schedule.Your Honda does not require any oil additives.Additives may adversely affect your engine’s or transmission’s performance and durability.Always change the oil and filter according to the recommendations in the maintenance schedule.The oil and filter collect contaminants that can damage your engine if they are not removed regularly.Changing the oil and filter requires special tools and access from underneath the vehicle.The vehicle should be raised on a service station-type hydraulic lift for this service.Unless you have the knowledge and proper equipment,you should have this maintenance done by a skilled mechanic.Open the hood and remove the engine oil fill cap.Remove the oil drain bolt and washer from the bottom of the engine.Drain the oil into an appropriate container.Run the engine until it reaches normal operating temperature,then shut it off.1.2.Adding Engine Oil,Changing the Oil and Filter Synthetic Oil Engine Oil Additives Changing the Oil and Filter 174Remove the oil filter and let the remaining oil drain.A special wrench (available from your Honda dealer)is required.Install a new oil filter according to the instructions that come with it.4.3.Changing the Oil and Filter175NOTICE:Improper disposal of engine oil can be harmf ul to the environment.If you change your own oil,please dispose of the used oil properly.Put it in a sealed container and take it to a recycling center.Do not discard it in a trash bin or dump it on the ground.。

自动变速箱档位指示灯组件位置索引自动变速箱档位指示灯F-CAN通讯电路故障处理，见22-222页仪表控制模块自诊断功能指示灯驱动电路检查，见22-208页通讯线路检查，见22-209页自动变速箱档位指示器灯光线束更换，见14-258页说明：图中所示左侧驾驶型；右侧驾驶型与此相对称。

变速箱档位开关测试，见14-254页更换，见14-256页说明：图中所示左侧驾驶型；右侧驾驶型与此相对称。

14-252.；14-253电路图CANH仪表控制模块白粉红 棕 黑 白/红 黑/蓝红/黑 蓝黄/红 蓝/白 红红/黑黑黑 棕/黄 棕/黄黑黑 F-CAN 收发器仪表板灯 亮度控制 电路自动变 速箱档 位指示 灯驱动 器电路自动变速 箱档位指 示灯盘灯棕灰黑/黄蓝/黄 黄 棕 红 黄/绿 红/黑 PCM 线束插头端子位置凹头插头端子侧C(44芯)B(44芯) A(44芯)黑蓝/白橙蓝/黑白/绿 白 白 红CANL动力系统控制模块(PCM)发动机盖下保险/继电器盒 点火开关仪表板下保险/继电器盒红 红灰 多路控制器(MICU)多路控制器(MICU)BAT蓄电池CAN 控制器变速箱档位开关起动机切 断继电器自动变速箱档位指示灯14-254变速箱档位开关的测试1. 拆下空气滤清器壳和进气导管(见11-308页)。

2. 断开变速箱档位开关线束插头(A)。

3. 检查线束插头处端子之间的导通性。

对于每个开关位置来说，下表中的各端子之间应导通。

变速箱档位开关线束插头4. 如果测试结果正常，则表示完成变速箱档位开关的测试。

如果任何端子之间不导通，则进行第5步。

5. 施加驻车制动，并阻止两后轮。

抬起车辆前部，并确保将其牢固支撑。

或举升车辆。

6. 拆下变速箱档位开关罩。

凸头插头端子侧插头端子/信号位 置.；14-2557. 断开变速箱档位开关插头。

8. 检查开关插头处端子之间的导通性。

对于每个开关位置来说，下表中的各端子之间应导通。

变速箱档位开关线束插头9. 如果变速箱档位开关导通性检查正常，则更换出现故障的变速箱档位开关线束。

燃油管路检查(续)检查所有夹具，如必要，重新拧紧。

基座垫片 更换锁紧螺母板 更换燃油箱装置锁紧螺母 更换安装燃油加注颈管时，将导管标记与燃油加注颈接头凸舌对齐。

此处应无间隙。

顶面确认夹钳处于如图所示杆端量程以内位置。

确认夹钳处于如图所示杆端量程以内位置。

此处应无间隙。

确认夹钳处于如图所 示杆端量程以内位置。

确认夹钳处于如图所 示杆端量程以内位置。

至分油器至燃油蒸发排放(EVAP)活性炭罐净化阀确认夹钳处于如图所示位置。

燃油管路/快速接头操作前注意事项燃油管路/快速接头(A)与(B)用于将分油器(C)连接至燃油供给软管(D)、将燃油供给软管连接至燃油管路(E)以及将燃油管路(F)连接至燃油箱装置(G)。

拆卸或安装燃油供给软管、燃油箱装置或燃油泵时，必须断开或连接快速接头。

注意以下事项：• 燃油供给软管、燃油管路与快速接头不耐热，因此在进行焊接或其他热生产操作时要小心，不要损坏这些组件。

• 燃油供给软管、燃油管路与快速接头不耐酸，当用维修用布擦干蓄电池电解溶液后，不得再接触这些组件。

一旦与电解液或类似物质接触，则予以更换。

•连接或断开燃油供给软管、燃油管路与快速接头时，小心不得将其过度弯曲或扭曲。

如果损坏，则予以更换。

已拆下的快速接头可以重新连接，但是配合管路的固定座一旦从管路上拆下后，就不得再次使用。

在下列情况下，应更换固定座。

•更换分油器。

•更换燃油管路。

• 更换燃油泵。

•更换燃油滤清器。

•更换燃油量信号发送装置。

•固定座已从管路上拆下。

• 固定座损坏。

位置制造商固定座管路直径A Tokai 绿 6.3 mm (0.3 in.)B Sanoh 白9.5 mm (0.4 in.)燃油管路/快速接头的拆卸说明：在燃油管路与接头上进行操作时，请阅读“燃油管路/快速接头操作前注意事项”(见11-285页)。

1. 释放燃油压力(见11-279页)。

2. 检查燃油快速接头(A)是否脏污，如有必要，进行清理。

传动系/轴专用工具 ......................................... 16-2组件位置索引 ..................................... 16-3驱动轴的检查 ..................................... 16-4驱动轴的拆卸 ..................................... 16-4驱动轴的拆解 ..................................... 16-6缓冲块的更换 ..................................... 16-10驱动轴的重新组装 ................................. 16-11驱动轴的安装 ..................................... 16-19中间轴的拆卸 ..................................... 16-21中间轴的拆解 ..................................... 16-22中间轴的重新组装 ................................. 16-23中间轴的安装 ..................................... 16-25专用工具序号工具编号工具名称数量07GAD-PH70201油封拆装器107NAF-SR30101半轴支座107XAC-0010100螺纹适配器，22×1.5 mm107746-0010400附件，52×55 mm107746-0030400附件，35 mm，内径107749-0010000拆装导柱107947-SB00100油封拆装器1组件位置索引中间轴拆卸，见16-21页拆解，见16-22页重新组装，见16-23页安装，见16-25页驱动轴检查，见16-4页拆卸，见16-4页拆解，见16-6页重新组装，见16-11页安装，见16-19页缓冲块更换，见16-10页驱动轴的检查驱动轴的拆卸1. 检查驱动轴(C)上的内侧防护套(A)和外侧防护套(B)是否有裂缝、损坏、渗漏润滑脂等现象，并松开防护套卡环(D)。

东风本田思域维修电路图（本田思域电路图册199）电路图索引空调 (22)SRS 指示灯................................ 3 防抱死系统(A BC).. (21)转向指示灯................................. 3 音响 (13)行李箱/背舱门指示灯.................... 2 电瓶 (1)钥匙插入提示灯.............................. 15 充电系统 (1)遥控开启车门系统........................... 16,17 点烟器 (12)照明系统....................................... 5,6,7 温湿控制 (22)外部照明....................................... 定速巡航控制 (21)倒车灯....................................... 8 仪表板灯亮度控制 (2)制动灯....................................... 8 白昼行车灯 (7)前驻车灯.................................... 6 电子动力转向(EPS) . (20)前示宽灯……………………………… 5,6,7 发动机控制模块(ECM) ………………… 24,27前大灯....................................... 5,6,7 风扇控制.. (22)高位制动灯................................. 8 仪表.. (2)牌照灯...................................... 5,6,7 加热器控制 (22)尾灯......................................... 5,6,7 前大灯调整 (9)转向灯...................................... 8 前大灯清洗器 (14)内部照明....................................... 喇叭 (9)车顶灯....................................... 9 点火开关 (1)杂物箱灯................................... 15 点火系统 (1)点火钥匙灯................................ 5 联锁系统 (15)聚光灯………………………………... 9 防起动系统……………………………… 24,27行李箱/背舱门灯……………………. 9 指示灯多路控制....................................... 15 ABS 指示灯 (3)动力系统控制模块(PCM) .................. 24,27 A/T 档位指示灯 (4)电动车门锁.................................... 16,17 定速巡航指示灯 (3)电动后视镜.................................... 10 车门指示灯 (2)电动车窗....................................... 11 EPS 指示灯.. (3)后窗除雾器.................................... 22,23 前雾灯指示灯 (3)座椅加热器.................................... 13 远光指示灯 (3)防盗安全控制................................. 18,19 燃油量少指示灯 (2)换档锁定系统................................. 15 低机油压力指示灯 (2)高级锁定系统................................. 16 异常、需修理指示灯 (2)起动系统....................................... 1 故障指示灯 (3)辅助保护系统(SRS) ........................ 20 后雾灯指示灯 (3)转向信号/危险报警灯....................... 8 座椅安全带提示灯 (2)车速传感器(VSS) ........................... 2 侧安全气囊指示灯 (3)刮水器/清洗器 (14)汽车技师帮技术资料东风本田思域维修电路图(本田思域电路图册199)。

中间轴拆卸和安装注意：如何读取规定扭矩。

除非特别说明，步骤中使用的图示为 1.5 L 发动机。

1. 车辆 - 举升2. 变速器油 -排空M/TCVT3. 右前轮 - 拆卸4. 右驱动轴 - 拆卸5. 中间轴 - 拆卸注意：水平夹持中间轴，直至与差速器有一定间隙，以防止损坏油封 (A)。

6. 所有拆下的零件 - 安装1.用溶剂彻底清洁中间轴和差速器的接触部位，并用压缩空气吹干。

注意：不要用溶剂清洗橡胶零件。

2.按照与拆卸相反的顺序安装零件。

7. 车轮定位 - 检查8. 行驶测试 - 检查中间轴拆解和重新组装所需专用工具图像说明/工具号码轴承拆装器附件，37 x 40 mm 07746-0010200轴承拆装器附件，52 x 55 mm 07746-0010400拆装器手柄，15 x 135L 07749-0010000图像说明/工具号码拆装器，32.5 mm 070AD-SAA0100油封拆装器，65 mm 07JAD-PL90100半轴底座 07NAF-SR30101显示了图标时，点击获取更多信息。

用溶剂清洗拆下的零件，并用压缩空气吹干。

切勿用溶剂清洗橡胶零件。

11.0 L 发动机详细信息、注意和注意事项更换21.5 L 发动机详细信息、注意和注意事项更换1.0 L 发动机1. 外密封件 - 拆卸2. 外卡环 - 拆卸1.拆下外部卡环 (A)。

3. 中间轴 - 拆卸1.用半轴底座和压力机将中间轴 (A) 压出中间轴轴承 (B)。

注意：拆解时，小心不要损坏中间轴上的轴承支撑环 (C)。

4. 内卡环 - 拆卸5. 中间轴轴承 - 拆卸1.5 L 发动机1.用 15 x 135L 拆装器手柄、半轴底座、37 x 40 mm 轴承拆装器附件和压力机将中间轴轴承 (A) 压出轴承支架 (B)。

1. 外密封件 - 拆卸2. 外卡环 - 拆卸1.拆下外部卡环 (A)。

3. 中间轴 - 拆卸1.用半轴底座和压力机将中间轴 (A) 压出中间轴轴承 (B)。

Avoid exceeding your vehicle’s load limit.This puts excess stress on the engine,brakes,and many other parts of your vehicle.The load limit is shown on the label on the driver’s doorjamb.Your vehicle displays engine oil life and maintenance service items on the information display to show you when you should have your dealer do engine oil replacement and indicated maintenance service.The fuel system is under highpressure (maximum 3,600psi/24,800kPa).It has no user-serviceable parts,and its components must not be modified.Whenever fuel system maintenance is required,take your vehicle to an authorized Honda Civic GX dealer,or a qualified NGV technician.Refer to the important safetyprecautions and instructions in the Civic Sedan owner’s manual.Operate your vehicle onreasonable roads within the legal speed limit.Drive your vehicle regularly over a distance of several miles (kilometers).Maintenance MinderTo see the current engine oil life, turn the ignition switch to the ON (II)position,and press the SEL/ RESET button repeatedly until the engine oil life display appears.The maintenance item code or codes indicate the main and sub items required at the time of the oil change.CONTINUEDEngine Oil Life Display Maintenance MinderIf you have the required service done but do not reset the display, or reset the display without doing the service, the system will not show the proper maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed.We recommend using Honda parts and fluids whenever you have maintenance done. These are manufactured to the same high quality standards as the original components, so you can be confident of their performance and durability.However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Make sure to have the service facility or person reset the display as previously described. Keep all receipts as proof of completion, and have the person who does the work fill out the maintenance record or the Honda service history booklet. Check your warranty booklet for more information.When the remaining engine oil life is5 to 1 percent, you will see a ‘‘SERVICE OIL LIFE’’ message along with the same maintenance item code(s),every time you turn the ignition switch to the ON (II)position.For information on maintenance codes,see page ,or refer to the Civic Sedan owner’s manual.Your authorized Honda dealer knows your vehicle best and can provide competent,efficient service.For information on resetting the maintenance minder,refer to the Civic Sedan owner’s manual.19Important Maintenance Precautions Maintenance MinderMaintenance Minder:Independent of the maintenance messages in the information display,replace the brake fluid every 3 years.Inspect idle speed every 160,000 miles (256,000 km).If sub-item 2 does not appear more than 36 months after the display is reset,inspect the fuel tank every 3 years.See Fuel Tank on page 23 for inspection and replacement information.The fuel tank should be replaced 15 years after it was manufactured.Adjust the valves during services A, B, 1, 2, or 3 only if they are noisy.Seeinformation on maintenance and emissions warranty in the second column on page of the Civic Sedan owner’s manual.NOTE:2:218MaintenanceMinderMaintenance Recordmi mi mi mi mi mi mi mi mi mi mi mi mi miYou or the servicing dealer can record all completed maintenance here.When maintenance is performed,record the mileage,circle the coded item(s) completed,and write in any other non-coded items(such as brake fluid replacement)below the codes.Keep the receipts for all work done on your vehicle.Maintenance can also be recorded in your Honda service history booklet.MileagekmkmkmkmkmkmkmSignatureDateMileagekmkmkmkmkmkmkmSignatureDate MaintenancePerformedA B12345A B12345A B12345A B12345A B12345A B12345A B12345MaintenancePerformedA B12345A B12345A B12345A B12345A B12345A B12345A B12345Maintenance Recordmi mi mi mi mi mi mi mi mi mi mi mi mi miMileagekmkmkmkmkmkmkmSignatureDateMileagekmkmkmkmkmkmkmSignatureDate MaintenancePerformedA B12345A B12345A B12345A B12345A B12345A B12345A B12345MaintenancePerformedA B12345A B12345A B12345A B12345A B12345A B12345A B12345Engine coolant change capacity:The SAE number tells you the oil’sviscosity or weight.Select theoil for your vehicle accordingto this chart.Refer to the Civic Sedan owner’s manual for engine coolant checking and adding procedures.Engine OilEngine CoolantEngine Oil,Engine Coolant1.37US gal (5.2)。