BC6900A绝缘油介电强度测试仪

Z I J J-Ⅱ绝缘油介电强度全自动测试仪一、简介ZIJJ-Ⅱ型绝缘油介电强度自动测试仪是依据国际IEC－156和国标GB507-86《绝缘油介电强度测定法》的要求，同广大使用者的反馈意见，在HCJ－9101的基础上，开发的全自动化仪器。

本仪器选用单片机为主导，先设定后开机测试的方法，全部过程由微机自动运行控制，操作简单，方便适用。

二、用途与特点本仪器适合测试各种绝缘油介电强度。

其主要性能特点：1.本仪器设有自动检测功能，如开机自动进入复位状态执行调压器回零。

２.采用了微型TPU－A面板式打印机，自动打印输出。

３.根据用户需求可改变测试次数、搅拌静置时间、声控光控提醒连续打印与非打印。

４.本仪器采用全自动磁振子搅拌，消除油样的不均匀和气泡。

三、技术规格１.工作电源：AC220V ±10%、50HZ ±5%２.测量范围：AC 0－80KV３.限定电流：5mA４.测量精度：1%５.调压速度：2KV/S±10%６.预定设置：次数1－9搅拌时间 0－1分39秒静置时间 0－10分39秒７.使用条件：环境温度0℃－35℃相对湿度≤75%８. 油杯间隙：2.5mm(油杯塞尺直径)９. 体积: 415×315×315mm3１０. 重量：28kg四、面板说明图一面板示意图（１）电源开关（２）电源插座（３）高压舱（４）安全开关（５）安全接地（６）Ａ保险（７）显示屏（８）设置盘（９）指示灯（１０）键盘（１１）打印机五、操作步骤1. 输入电源连接安全接地，插入220V交流电源，检测电源正确无误。

2. 取油样2.１将油杯两电极间距调整在 2.5mm ；逆时针旋下油杯轴杆一端的塞尺棒，将另一端电极调整在偏中位置，将锁住此轴杆的螺钉旋紧，取塞尺棒于两电极间靠紧两电极，锁住螺钉取出塞尺，顺时针旋于原轴杆内，如图二。

图二高压舱内布置图（１）高压舱（２）高压柱（３）轴杆（４）电极（５）塞尺（６）油杯（７）轴杆固定螺丝（８）磁振子2.２将油杯处理干净，置干净的磁振子于油杯内，注满准备好的油样，取下高压罩置油杯于高压舱两高压柱间，平稳放置盖上高压罩压好安全开关。

中华人民共和国国家标准UDC665.546∶543.25绝缘油介电强度测定方法GB507—86代替GB507—77Insulating oils-Determinationof the dielectric strength国家标准局1986-06-25发布1987-06-01实施本方法适用于验收20℃时粘度不大于50mm2/s的各种绝缘油。

例如：变压器油、电容器油、电缆油等新油或使用过的油，但主要是用于新油。

介电强度并不是用来评定绝缘油质量的一个标准，而是一项常规试验。

它是用来阐明绝缘油被水和其他悬浮物质物理污染的程度以及打算注入设备前进行干燥和过滤是否适宜。

本标准是参照采用国际电工委员会标准IEC156《绝缘油介电强度测定法》制订的。

1 方法概要测定方法是将放在专门设备里的被测试样经受一个按一定速率连续升压的交变电场的作用直至油击穿。

测量值与所用的测量设备和采用的方法有很大关系。

2 仪器2.1 变压器2.1.1 试验电压是从交流(50Hz)的低压电源供电的一个升压变压器得到的。

通过手调或自动控制装置逐渐增加初级线圈电压，经升压后的次级线圈电压施加于试验油杯的电极上。

该电压应是一近似正弦的波形，其峰值因数应在2±5% 范围。

2.1.2 变压器和相配的装置应能在电压大于15kV时产生一个20mA的最小短路电流。

2.2 保护装置2.2.1 装置应良好接地。

2.2.2 进行试验时尽可能防止产生高频振荡。

2.2.3 为了保护设备和避免试油在击穿瞬间的分解，可与试验油杯串联一个电阻，以限制击穿电流。

2.2.4 高压变压器的初级电路上接一个断路器，这个断路器能在试样击穿后不超过0.02s的时间内因试样的击穿电流作用而动作。

断路器接一个无电压释放线圈以保护设备。

2.3 电压调节2.3.1 电压调节可用下列设备之一来实现：2.3.1.1 变比自耦变压器。

2.3.1.2 电阻分压器。

2.3.1.3 发电机磁场调节。

绝缘油介电强度测试仪操作步骤
绝缘油介电强度测试仪操作步骤
绝缘油介电强度测试仪是电力部修订的《电力系数油质试验方法》中的规定和IEC－156和国标GB507-86《绝缘油介电强度测定法》，全自动型绝缘油介电强度测试仪以先进的微型计算机为控制及运算核心，采用的数字模型，特制了微弱信号传感器，避免了仪器自身的干扰，软件测量准确可靠。

全自动绝缘油介电强度测试仪采用中央处理器、大规模集成电路等先进技术组成自动化测试设备，操作过程全自动化，并能通过面板配置的微型打印机打印试油试验数据，该设备与普通仪表及同类型仪器相比具有试验稳定性好，精度高，操作性良好，该设备在试油操作中有多种试验运行方
全自动绝缘油介电强度测试仪操作步骤：
1、把油杯的电极调好，将油杯放在有机玻璃内两边的高压端上。

2、将搅拌电机的有机玻璃盖盖上油杯上，并将电机的插件插到搅拌插孔内。

3、将接地线接好，再插上电源线，打开电源开关，零位指示灯应亮，如果不亮，仪器将自动返回到零位。

4、当显示屏显示按“确认键，进入测试"时，应先设定“搅拌时间"、“测试次数"“静置时间"设定后按“复位键"完成设定。

5、按下“确认键"仪器开始自动按照设定好的指令开始测试当绝缘油击穿后，仪器自动搅拌，显示屏显示每次的试验电压，静置时间指令结束后，仪器自动计算出耐压强度的综合平均值并显示在液晶屏上。

6、如需打印，按下“打印键"即可打印出绝缘油介电强度的综合平均值。

绝缘油介电强度测试仪保养办法绝缘油介电强度测试仪通常用于检测电力设备中的绝缘油的介电强度，以评价绝缘油的质量以及判断电力设备的绝缘状态。

为了保证测试仪的精度和可靠性，需要对其进行定期保养。

本文将介绍绝缘油介电强度测试仪的保养办法。

保养前准备在进行保养前，需要检查绝缘油介电强度测试仪是否正常使用。

首先需要检查测试仪的外观是否完好无损，尤其是测试夹具的表面是否平整，测试电极是否清洁。

其次，需要检查测试仪的电源是否正常。

如果电源出现问题，应该先进行维修或更换。

日常保养在使用过程中，每天上岗前应该对测试仪进行简单的检查和清洁。

检查的具体内容如下：1.检查仪器的机箱、面板、连接器和线缆是否干净。

如不干净，应用软布擦拭干净。

2.检查测试仪的外观是否有损伤、老化、腐蚀等现象，如有应及时更换。

3.需要定期对测试夹具进行清洗，以确保测试电极表面光洁无污渍，避免测试误差。

4.检查仪器各项数据是否正常，保证测试准确无误。

定期保养在长时间使用后，绝缘油介电强度测试仪需要进行定期保养和维护，以确保测试仪的可靠性和准确度。

1.保养仪器内部。

每年至少需要将仪器拆开清洗，掌握好清洗时连接线的位置和数量，保证拆卸后不会出现连接线错误的情况。

2.更换测试仪内部的灯泡和其他易损件，以确保测试仪的运行质量。

3.按照说明书进行液晶显示屏的清洗和维护，避免其老化或坏点的出现。

保养后注意事项在完成保养后，需要重新进行检查以确保设备正常运行。

以下是一些需要注意的事项：1.重新连接测试夹具和电源，检查夹具是否正常，是否存在锈蚀或损伤。

2.清理测试仪放置的区域，确保周围的工具和仪器没有对测试仪造成伤害。

3.关注测试仪的所有操作，保护好测试仪。

总结绝缘油介电强度测试仪是一种非常重要的绝缘测试仪器，为保证其测量的准确性和可靠性，需要进行定期的保养和维护。

在日常工作中，需要认真检查测试仪器的各项部件是否正常，保持设备的干净卫生。

同时，还要定期进行更换易损件，确保测试仪的性能始终处于最佳状态。

1BC BC--7000CAPACITY TESTEROPERATIONS MANUALCOFKO LLC.COPYRIGHT © 2013To buy, sell, rent or trade-in this product please click on the link below:https:///Power-Products-BC-7000-Battery-Charger.aspxUNPACKINGAs you unpack your new BC-7000 battery capacity tester, inspect the tester for signs of shipping damage. If shipping damage is present, stop and contact the shipping company for damage claims information. The box should contain the BC-7000 tester, operators instruction manual, AC power cord, USB cable, battery disconnect (7017-2), 2 battery adapter cables, and BC Report software.IMPORTANT: Save the shipping box and packaging material. They should be used to repack the tester if it needs to be shipped back for warranty or service.2INTRODUCTIONCongratulations on acquiring your new BC-7000 battery capacity tester. The BC-7000 battery capacity tester has been designed to provide the operator with accurate battery capacity testing and ease of operation.The features of the BC-7000 are:- Adjustable constant current load in 0.1 Ampere increments from 0.5 Ampere to 15 Ampere.- Adjustable constant current load in 1.0 Ampere increments from 15 Ampere to 55 Ampere.- Universal AC power input 85~264Vac 1 PH (47 to 63Hz)- LCD display.- 10mv voltage resolution.- Over temperature protection.- Audio warning when capacity test is complete or malfunction of the unit.- USB 2.0 port for PC connection.- Windows TM XP or Higher compatible BC Report Utility software for test data hardcopy print out.- Real time internal clock with battery backup.- 1 year warranty.Before operating your new BC-7000 battery capacity tester, familiarize yourself with this operators manual and the unit.Questions?Call: (909) 705-6267 Mon.-Fri.8:00 A.M. to 5:00 P.M. PST or *****************Thank you,COFKOManual: BC-7000Revision: C Date: 04/05/133CONTENTS PAGEBC-8000 History of Revisions (5)BC-7000 SAFETY NOTES ………………………………………………………………….…….................................................… 6,7BC REPORT UTILITY AND REAL TIME CLOCK SETUP (8)BC-7000 OPERATION …………………………………………......................................................................…....……. 9,10,11BC-7000 REPORT PRINTING (11)BC-7000 CARE (12)BC-7000 TECHNICAL DATA ……………………………………………………………………………......................…..................….. 13,14BC-7000 LIMITED WARRANTY (15)BC-7000 NOTES (16)BC-7000 CERTIFCATION OF FACTORY CALIBRATION (17)4History of RevisionsRevision #Effective Date Description of Change Approval ByA11/11/2010Initial issue M.C.B10/23/2012Increase Maximum Operation Altitude from 6000’ to 6500’ M.CB10/23/2012Change Description of Box Contents M.C.C04/05/2013Minimum and Maximum Operation Temperature M.C.56SAFETY NOTESYour new BC-7000 battery capacity tester has been designed with operator safety as a function of its design,construction, and operation. Understanding how to safely operate the BC-7000 battery capacity tester is important. Failure to follow the operation and safety guidelines when using the BC-7000 can result in personal injury to the operator and damage to the BC-7000. Always review the battery manufacturer’s battery capacity testing guidelinesbefore testing batteries.Look for this symbol to identify Safety and Danger precautions. Be Alert- Your safety isinvolved! Personal injury or equipment damage can occur if guidelines are not followed. PRECAUTIONS:Precautions:1 CAUTION: Aircraft batteries are certified to have a certain minimum capacity for emergency operations inthe event of an electrical generator system failure. Never “jump start” an aircraft that has a discharged or“dead” battery.2 WARNING: ELECTRIC SHOCK HAZARD. Do not touch un-insulated portions of the connector or the batteryterminals. A possibility of serious electrical shock exists. Do not lay tools or other metal objects on thebattery as arcing or explosion could occur. Remove conductive jewelry before working around battery,charger, or test equipment.3 CAUTION: ELECTRIC BURN HAZARD. Do not wear conductive rings, belt buckles, or other jewelry whenworking with batteries, chargers, or test equipment. Do not lay tools or other metal objects on the batteryas arcing and severe burns could occur.4 WARNING: Batteries on charge or discharge produce hydrogen gas, which can explode if ignited. Do notsmoke, use an open flame, or cause sparking near a battery. Charge, service or test a battery only in a wellventilated area. The use of exhaust fans may reduce the risk of explosion.5 WARNING: Batteries contain sulfuric acid which will cause burns . DO NOT TOUCH EYES AFTER TOUCHINGBATTERY . Do not get acid in your eyes, or on your skin, or clothing. In the event of acid in the eyes, flushthoroughly with clean cool water for several minutes. Get professional medical attention. Refer to batteryMSDS for additional information.6 WARNING: Wear proper eye, face and hand protection at all times when working with batteries. Know thelocation and use of emergency eyewash and shower nearest the battery charging area.7 CAUTION: To prevent damage to the connector, arc burns, or explosion, batteries should never beconnected or disconnected while being charged or discharged. Batteries must be connected or disconnected only when the circuit is open. Ensure the aircraft battery switch, external power source, or thecharger/analyzer is in the “OFF” position before connecting or disconnecting the battery. Battery terminal protectors should be installed whenever the battery is not connected in the aircraft or to the testequipment.8 CAUTION: Batteries contain hazardous materials. Know the location and proper use of emergency responsematerials. Refer to battery Material Safety Data Sheet (MSDS) for additional information.9 Caution / Warning: Only constant potential charging may be done on the aircraft. DO NOT constant currentcharge a battery on the aircraft. There could be a serious risk of injury to personnel and / or damage to the aircraft or aircraft systems due to high voltage and generation of explosive gases when charging constant current.10 DANGER: Never connect or disconnect BC-7000 tester main power connector with the switch on. Connectingor disconnecting the BC-7000 tester with discharge current applied can cause a spark and possible battery explosion.11 DANGER: Never capacity test batteries without first inspecting all battery wires and connection for conditionand tightness. Replace all defective wires and bad connections before capacity testing batteries. Defective wiring and bad connections can cause overheating during a capacity test.12 DANGER: never connect the BC-7000 capacity tester to batteries with voltage or capacity currents outsidethe ratings of the tester. The BC-7000 tester is designed for 12 and 24 volt batteries. Connecting the tester to batteries with different voltages can permanently damage the tester and endanger the operator. Anyquestionsthatariseaboutthebatteryortesterratings,**********************13 DANGER: never obstruct the BC-7000 tester air intake or hot air exhaust openings. Obstructing eitheropening can cause the tester to overheat.7BC Report Utility and Real Time Clock SetupNOTE: The BC Report Utility software MUST be installed on the computer used to connect to the BC-7000 tester first. Do not connect the USB communication cable to the BC-7000 until this is done.1 Remove the BC Report Utility CD from the protective sleeve and place disk into the PC CD drive. The BC Report Utility will automatically start installing. (Manual installation can be done with commands: Start\Run\ d:\setup.exe2 Windows Application Security Warning dialog box may prompt you about installing the BC Report Utility. To continue installing the BC Report Utility, click on the INSTALL button. The installation may take some time as Windows TM installs all the necessary software.3 When prompted to install the Silicon Labs CP210x USB to UART bridge driver, click the INSTALL button to install all needed drivers. (C:\Program Files\Silabs\MCU\CP210x\) Note: The CP210x drivers are on the BC Report Utility CD disk.4 After the BC Report Utility software installation is completed, remove the BC Report Utility CD disk from the drive and return to the protective sleeve. Now restart the PC .5 The Windows TM desktop should now contain the BC Report Utility program icon. Plug the USB cable supplied with the BC-7000 into a working USB port on the PC with the BC Report Utility installed. Connect the AC power cord to the BC-7000 and set the power switch to the ON position. Now plug the remaining USB cable end into the USB port located on the right side rear of the BC-7000. If the connection is made between the PC and the BC-7000 the PC may respond with an audio sound confirming a device has been found.6 To run the BC Report Utility, place the mouse pointer on the icon and press the left mouse button. This action will start the BC Report Utility program and display the program window.7 Before updating the BC-7000 internal date and clock, check the computer date and time for proper setting and adjust if needed. This is the date and time the BC-7000 will use. Located in the lower middle of the BC-7000 Report window is the SET Date & Time button. To set the BC-7000 Date & Time place the mouse pointer on the Set Date & Time button and click the left mouse button. The status bar located in the lower left corner will display a series of messages showing the communications activity between the BC-7000 and the PC. The first message displayed is Searching for BC-7000. Second message is Setting Date and Time. And the final message will be Done. With the date and time set, the BC-7000 is now ready to test batteries and print test result reports.8 If any difficulties are experienced with communications between the BC-7000 and the PC, check cable connections first and review BC Report Utility installation second. Lastly make sure the PC USB port drivers are installed and working. Review your Windows TM software help menu for guidelines in checking USB ports.89BC-7000 OPERATIONNOTE: Before capacity testing a battery, review all testing procedures as required by the batterymanufacturer. Failure to do so can result in inaccurate test date.NOTE: Before capacity testing a battery, RECHARGE THE BATTERY FOLLOWING THE MANUFACTURERS RECHARGING GUIDELINES.NOTE: Before putting the BC-7000 into service the REAL TIME clock must be set. See instruction in the BC Report Utility section. Failure to do so will result in incorrect printed time on test reports.1. Make sure the power switch is in the OFF position. Connect the AC power cord female end into the powerreceptacle located in the left rear side of the BC-7000. Connect the male end of the power cord into the AC power outlet. Now connect the gray BC-7000 battery connector to the battery to be tested.DANGER: Never attempt to connect the BC-7000 capacity tester to a battery using anything but the proper connector. Doing so can damage the tester, battery, or cause injury to the operator . Capacity testing data will be invalid if incorrect connections are made.2. Place the OFF/ON power switch to the ON position. The BC-7000 LCD display will flash tester model andsoftware version.NOTE: If Replace Clock Coin Battery is displayed on screen, remove case top and install new coin battery. Replacement battery number is 3V #CR2032. Use BC Report Utility software to update date and time after battery10replacement. See BC Report Utility Software section for instructions.3. First select which Mode? CAPACITY or DISCHARGE to 1 Volt. Use the UP or DOWN button to change youselection. DISCHARGE mode is used to discharge Nickel Cadmium batteries.4. Push the NEXT button. Now select the battery voltage to be tested. Pressing the DOWN button will changebattery testing voltage to 12 volts.NOTE: If incorrect battery voltage is selected the BC-7000 display will inform the operator.5. Push the NEXT button . Select the End Point Voltage (EPV) cutoff. The default EPV is 20 volts for 24 volt battery and 10 volts for a 12 volt battery. The BC-7000 allows for EPV adjustment from the default values. For a 24 volt battery the EPV can be lowered to 18 volts. For 12 volt batteries the EPV can be lowered to 9 volts. Check with your battery manufacturer for specified EPV points.6. Push the NEXT button. Select the battery manufacturer C1 (one hour) battery discharge amperage rate. Press the UP or DOWN buttons. Pressing the UP button will increase the discharge amperage rate.7. Press the NEXT button to display the start test menu.8. To start the test, press the NEXT button again. If you wish to stop the test before the End Point Voltage (EPV) is reached, press the NEXT button and the BC-7000 will stop testing. If testing is stopped before EPV is reached the battery must be recharged following the battery manufacturer’s recharge procedures before retesting.9. After pressing the NEXT button to start the test, the BC-7000 cooling fan motor will start and the LCD display will show the C1% reading, battery voltage, flash TESTING , and test amperage. Note: While the BC-7000 is testing or at the conclusion of the test, pressing the UP button will display the test run time in minutes. The LCD will display TM: 60.2’ (The symbol ‘ indicates minutes)10. Upon reaching the EPV the BC-7000 test will stop. The cooling fan motor will stop and the audio warning beeperwill beep. The display will show C1% battery capacity. Test amperage and Pass or Failed is displayed.If the BC-7000 COOLING FAN MOTOR FAILS TO START press the NEXT button stopping the test. Place the OFF/ON switch to the OFF position and return the BC-7000 for service.“Passing” is based upon a battery capacity of 85% or greater of its C1 rating.“Failing” is a battery with less than 85% of its C1 rating.Before returning the battery to service follow the battery manufacturer’s recharging procedure.REMEMBER SAFETY FIRST!BC-7000 Report Printing1. Disconnect the BC-7000 from the test battery. Place the OFF/On power switch to the OFF position. Connect the USB cable from the PC to the BC-7000 USB port located in the rear of the tester. Start the PC and run the BC Report Utility software located on the Windows TM desktop.2. With the BC Report Utility window active on the desktop, type the battery serial number into the Battery Serial Number: box. Make sure the data source is From BC-7000 by highlighting the indicator circle.3. Place the mouse cursor on the Load Data button and press the left mouse button. The status bar in the lower left corner of the BC Report Utility window will display program activity and status messages as data is transferred.4. To print the report, place the mouse cursor on the Print Report button and press the left mouse button. The Windows TM print preview window will appear showing the report available to print. Place the mouse cursor on the printer icon and press the left mouse button.TIP: A paperless report copy can be obtained by using a print driver that will create a PDF file. These drivers are available for sale or freeware and install in the Windows TM printer devices. This report format allows BC-7000 test reports to be sent electronically by means of e-mail attachments .5. To print a BC-7000 battery test report that has been already down loaded, use the From Disc function to print the report. Change the file source From BC-7000 to From Disc. The data file uses the file extension .tdf. The file name is a combination of battery serial number, date, and time and can be found in the Concord file located at C:\Concord\BC-7000. Place the mouse cursor on the Load Data button and press the left mouse button. The Open test data file window will open on the desktop. Choose the data file that is to be printed by selecting the file with the left mouse button. Click Open at the bottom of the window. Place the mouse cursor on the Print Report button and press the left mouse button. The Print Preview window will become active on the disk top. To print report, left mouse click the printer icon.11BC-7000 CAREYour BC-7000 battery capacity tester should be treated as precision test equipment, misuse will shorten its ability to perform accurate battery testing. Some simple guidelines of care will insure years of trouble free operation.1. Do not drop the BC-7000 or expose it to rough handling.2. Do not expose the BC-7000 to water or fluids of any kind.3. Do not operate the BC-7000 in a closed up area.4. Do not connect the BC-7000 to batteries of improper voltage ratings.5. Do not operate the BC-7000 with the air intake or exhaust outlet blocked or restricted.6. Do not carry the BC-7000 by the main power cable.7. Do not operate the BC-7000 near flammable materials.8. Do not expose the BC-7000 to direct sunlight during operation.9. Do not expose the BC- 7000 to any other heat sources.10. Always call the technical support line for questions on BC-7000 safety and operation.PH:(909)705-6267,***********************REMEMBER SAFETY FIRST!12TECHNICAL DATABC-7000 SPECIFICATION:AC Input Voltage ………………………………......................................................... 90~264VAC 1 Phase (47 to 63Hz)AC Input Current ………………………………......................................................... 0.75A @115VAC ; 0.50A @ 230VACMaximum Battery Input Voltage ……………………………………………………………………………......... 28.0VDCMinimum Battery Input Voltage ………………………………………………………………….....…............. 9.0VDCMaximum Operating Altitude1………………………………....……………………………….................... 6500ft(1828.8m)End Point Voltage (EPV)212V Battery EPV …………………………………………………………………………........….. 10VDC IEC24V Battery EPV ………………………………………………………………………….........…. 20VDC IECConstant Current Load ………………………….…………………......................................….. 0.5Adc to 15Adc 0.1A steps (+ - 1.5%) ……………………………….......................................................... 15Adc to 55Adc 1A steps (+ - 1%)13Testing Operational Temperature3…………………………………………………………….............………….....… 59°F or higherOperation Temperature Range ………………………………............................................................... -20 to 50 Deg. CCase Length ……………………………………………….………………...............…....……. 12 in(304.8mm)Case Width …………..………………………………………………………..............……...… 9 in(228.6mm)Case Height ……………..……………………………………………............……......…..…… 7.5 in(190.5mm)Weight ……….………………………………………………………………..............….... 10 lbs(4.5kg)PC Communication Port ……….………………………………………………………………...............…... USB 2.0BC REPORT Utility Software ……….…………………………………………………..……............................ Windows TM XP or Higher1. Consult factory for testing above maximum altitude rating.2. Consult battery manufacturer for End Point Voltage (EPV).3. Based upon 24 hour battery temperature stabilization in a 59°F or higher environment before testing battery. Consultbattery manufacturer for capacity testing at higher or lower temperatures.14BC-7000 LIMITED WARRANTYSTATEMENT OF WARRANTYCOFKO LLC warrants to the original purchaser (end user) of the BC-7000 battery capacity tester that it will be free of defects in workmanship and materials. This warranty is void if COFKO LLC finds that the BC-7000 battery capacity tester has been subjected to improper care, abnormal operation, or modification.WARRANTY PERIOD:The warranty period covers the original purchaser (end user) from the date of shipping.1 Year: Covers each BC-7000 battery capacity tester for workmanship, material, and labor.TO OBTAIN WARRANTY COVERAGE:You are required to notify COFKO LLC, of any defects within the warranty period. Written notification is recommended.WARRANTY REPAIRS:If upon inspection COFKO LLC confirms the existence of a defect covered by this warranty, the defect will be corrected by repair or replacement at COFKO LLC option.WARRANTY COST:The purchaser must bear the cost of shipping the BC-7000 to COFKO LLC as well as the return shipping cost.IMPORTANT WARRANTY LIMITATIONS:1. COFKO LLC will not accept responsibility for repairs made without authorization.2. COFKO LLC shall not be liable for consequential damages (such as lost business, etc.) caused by a defect orreasonable delay in correcting a defect to the BC-7000 battery capacity tester.3. COFKO LLC liability under this warranty shall not exceed the cost of correcting the defective BC-7000 batterycapacity tester.4. This written warranty is the only expressed warranty covering the BC-7000 battery capacity tester. Allwarranties implied by law such as Warranty of Merchantability are limited to the duration of this limitedwarranty of the BC-7000 battery capacity tester. Check your local legal rights for further rights you may have.15BC-7000 NOTES1. ___________________________________________________________________________2. ___________________________________________________________________________3. ___________________________________________________________________________4. ___________________________________________________________________________5. ___________________________________________________________________________6. ___________________________________________________________________________7. ___________________________________________________________________________8. ___________________________________________________________________________9. ___________________________________________________________________________10. ___________________________________________________________________________16COFKO LLC.5517 RIVERVIEW DR.RIVERSIDE, CA. 92509(909) 705-6267support@CERTIFICATION OF FACTORY CALIBRATIONEQUIPMENT: BATTERY CAPACITY TESTERMODEL#: BC-7000Application : Automatic battery capacity tester for 12/24volt Lead-Acid aircraft batteries with C1 testratings between 0.5 to 50 ampere-hourSpecification:Universal AC Powered: 85~264vac (47 to 63Hz)Operation Voltage Range : 28VDC to 9VDCOperator Selected Battery Voltage: 24-12VdcOperator Selected C1 amperage level: 0.5 - 50AdcOperator Selected Test Amperage Steps: 0.1Adc steps 0.5A to 15Adc;1Adc steps 15A to 50Adc.(16X2) LCD Information Display.Displayed Voltage Resolution 10mvCutoff Voltage 12V Battery 10.00Vdc (IEC 60952-1) +/-100mvCutoff Voltage 24V Battery 20.00Vdc (IEC 60952-1) +/-100mvDisplayed Battery Capacity (C1) Percent %Displayed Pass or Fail Battery ConditionWindows TM Compatible Test Data Print Utility (BC Report Utility)Notes: Calibrated with NIST traceable equipment.Test Equipment Manufacturer: Model: Serial# Control#Volt Meter #1 HP 3456A 2015A01818 12617Volt Meter #2 HP 3455A 1622A11888 12618Frequency Counter HP 5316A 2632A10545 12693Shunt Deltec WB 100 100 NA. 137317MLQA5Product: Automatic Battery Capacity TesterModel: BC-7000Calibration Due: Once A YearShipped Condition: Calibrated within Specified Tolerance _____- PassedProcedure: CF1_FINALCALCOFKO LLC. CERTIFIES THAT THE ABOVE LISTED TEST EQUIPMENT MEETS OR EXCEEDS ALL SPECIFIED TOLERANCES. THE TESTER STATED ABOVE HAS BEEN CALIBRATED WITH NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY(NIST) TRACEABLE EQUIPMENT LISTED ABOVE.DATE MANUFACTURED:____/____/_______ S/N: ________________________1SIGNATURE:__________________________-----------------------------------------------------------------------------------------------------------------------------------------------------------------------Date of First Use: ____/____/______ Signature:________________________1. BC-7000 serial number location- bottom of case.17。

JJG(冀)112—2012绝缘油介电强度测试仪检定规程1范围本规程适用于绝缘油介电强度测试仪（以下简称测试仪）的首次检定、后续检定和使用中检验。

本规程不涉及测试仪试验油杯和电极的检定。

2引用文件JJF 1001-2011 通用计量术语及定义 JJF 1002-2010 国家计量检定规程编写规则 JJG 795-2004 耐电压测试仪GB/T 507-2002 绝缘油 击穿电压测定法使用本规程时，应注意使用上述引用文献的现行有效版本。

3 概述测试仪是对绝缘油的抗电性能进行试验的仪器，按显示方式可分为数字式和模拟指示式两种，主要有高压发生、定时、报警、指示、输出电压调节装置等部分组成。

测试仪能手动或自动调整输出的交流试验电压。

在试验中，当油样被击穿时，测试仪能自动切断输出电压并同时报警，以确定被试油样能否承受规定的介电强度试验电压。

4 计量性能要求 4.1 交流输出电压4.1.1 测试仪交流输出电压基值误差用下式表示：nnx U U U U -=δ×100% (1) 式中： U δ——输出电压相对误差,%；x U ——输出电压示值，kV ； n U ——输出电压实际值，kV 。

4.1.2 数字式测试仪的基值误差用以下方式表达。

4.1.2.1. 绝对误差表示式)%%(m x U b U a +±=∆ (2) 式中：U x ——输出电压的读数值（显示值）；U m ——所检量程的满度值；JJG(冀)112—2012a ——与读数有关的误差系数；b ——与满度值有关的误差系数。

取b =0.1a 4.1.2.2 相对误差表示式x m x n m x U U b U a U U b U a /)%%(/)%%(+±≈+±=δ=)/%%(x m U U b a +± (3) 式中：U n ——输出电压实际值。

绝缘油介电强度测试仪交流输出电压准确度等级与最大允许误差见表1。

绝缘油介电强度测试仪基本原理绝缘油介电强度测试仪是依照国际电工委员会标准国际IECT56和国标GB507-86《绝缘油介电强度测定法》的要求，充分考虑国内外使用者的需求而研发的新一代全自动试油器，以单片机为主导，采用先设定后开机测试的方法，全部过程由微机自动运行控制，操作简单。

操作分为全自动六次和全自动单次操作，具有自动升压测试、自动搅拌、自动处理、自动打印及数字显示和锁定技术等功能，读数直观，测量准确，测试过程安全可靠。

全自动绝缘油介电强度测试仪增加了万年历和实验数据可长期保存的功能,将数码显示改为液晶显示。

控制器采用单片微型计算机测试全过程,抗干扰性能特强,完全克服了现行液晶自动测试仪易受高压击穿干扰的弊病。

不仅具有提高工作效率，使单调，重复，枯燥的工作变得颇有意味，而且安全，可靠，测量准确。

本仪器操作简单：除首次需将预置按到您所需要的数据外（若按国标测量此步可省，因出厂时已按国标预置了数据。

次数为6次，搅拌时间为1分钟，静置时间为5分钟）以后只按测值键便可。

运行方式的多样性是为用户不同的需要而设计的。

绝缘油介电强度测试仪主要特点：绝缘油介电强度测试仪设有自动检测功能，开机自动进入复位状态执行调压器回零；根据用户需求可改变测试次数、搅拌静置时间、声控光控提醒连续打印与非打印；本仪器采用全自动磁振子搅拌，消除油样的不均匀和气泡；采用了微型TPU-A面板式打印机，自动打印输出。

绝缘油介电强度测试仪基本原理：采用中央处理器、大规模集成电路等先进技术组成自动化测试设备，操作过程全自动化，并能通过面板配置的微型打印机打印试油试验数据，该设备与普通仪表及同类型仪器相比具有试验稳定性好，精度高，并具有良好的操作性，该设备在试油操作中有多种试验运行方式,主要特点：1全自动试验方式：连续6次试验，自动求平均值，通过面板打印机来打印出6次试验数据及平均数。

2.单次自动试验方式：自动完成1次试验，并打印出单次试验数据。

B C6900A绝缘油介电强度测试仪使用说明书宝应中测电气设备厂一、简介BC6900A型绝缘油介电强度测试仪是依据国际IEC－156和国标GB507-86《绝缘油介电强度测定法》的要求，同广大使用者的反馈意见，在HCJ－9101的基础上，开发的全自动化仪器。

本仪器选用单片机为主导，先设定后开机测试的方法，全部过程由微机自动运行控制，操作简单，方便适用。

二、用途与特点本仪器适合测试各种绝缘油介电强度。

其主要性能特点：1.本仪器设有自动检测功能，如开机自动进入复位状态执行调压器回零。

２.采用了微型TPU－A面板式打印机，自动打印输出。

３.根据用户需求可改变测试次数、搅拌静置时间、声控光控提醒连续打印与非打印。

４.本仪器采用全自动磁振子搅拌，消除油样的不均匀和气泡。

三、技术规格１.工作电源：AC220V ±10%、50HZ ±5%２.测量范围：AC 0－80KV３.限定电流：5mA４.测量精度：3%５.调压速度：2KV/S±10%６.预定设置：次数1－9搅拌时间 0－1分39秒静置时间 0－10分39秒７.使用条件：环境温度0℃－35℃相对湿度≤75%８. 油杯间隙：2.5mm(油杯塞尺直径)９. 体积: 415×315×315mm3１０. 重量：28kg1四、面板说明图一面板示意图（１）电源开关（２）电源插座（３）高压舱（４）安全开关（５）安全接地（６）Ａ保险（７）显示屏（８）设置盘（９）指示灯（１０）键盘（１１）打印机五、操作步骤1. 输入电源连接安全接地，插入220V交流电源，检测电源正确无误。

2. 取油样2.１将油杯两电极间距调整在2.5mm ；逆时针旋下油杯轴杆一端的塞尺棒，将另一端电极调整在偏中位置，将锁住此轴杆的螺钉旋紧，取塞尺棒于两电极间靠紧两电极，锁住螺钉取出塞尺，顺时针旋于原轴杆内，如图二。

2图二高压舱内布置图（１）高压舱（２）高压柱（３）轴杆（４）电极（５）塞尺（６）油杯（７）轴杆固定螺丝（８）磁振子2.将油杯处理干净，置干净的磁振子于油杯内，注满准备好的油样，取下高压罩置油杯于高压舱两高压柱间，平稳放置盖上高压罩压好安全开关。

【强度测试仪】绝缘油介电强度测试仪保养方法强度测试仪维护和修理保养绝缘油介电强度测试仪的油杯和电极必需保持清洁，在连续使用一个月后，需进行一次检查。

电极距离、电极表面是否发暗等，都需要检查，以适时进行调整，并用绸布擦拭电极表面。

假如仪器停用，则需要用盛新绝缘油的方法进行保护，确保油杯不受潮。

仪器长时间不使用时，则需要至少一个月通一次电。

仪器应避开雨水、腐蚀气体,尘埃过浓,高温或阳光直射等，由专门的人员进行管理和维护。

绝缘油介电强度测试仪保养方法:1.测试完后用油清洗油杯，用柔嫩的麂皮或绸布擦净电极表面保持干净，注满清洁干燥的油保护油杯。

2.使用或存放本仪器应在干燥、通风安全的地方。

3.绝缘油介电强度测试仪实行三包，在正常使用和保管情况下，本仪器保修一年。

4.在保修期内凡属质量导致故障而不能正常运转，本厂负责免费修理。

5.保修期内由于操作或保养不当，导致绝缘油介电强度测试仪损坏，本厂可优惠供应零部件与维护和修理。

6.用户在使用中如有绝缘油介电强度测试仪工作异常或需要技术咨询等方面的问题，请适时与厂家进行联系。

保鲜膜拉伸强度测试仪的功能用途与特点有哪些？保鲜膜拉伸强度测试仪是用来对材料进行静载、拉伸、压缩、弯曲、剪切、剥离等力学性能试验用的机械加力的试验机，适用于塑料板材、管材、异型材，塑料薄膜及橡胶、电线电缆、防水卷材、金属丝、金属绳等材料的各种物理机械性能测试。

其使用行业范围遍布：科研院所、商检仲裁机构、大专院校以及橡胶、轮胎、塑料、电线电缆、制鞋、皮革、纺织、包装、建材、石化、等行业，为材料开发、物性试验、教学讨论、质量掌控、进料检验、生产线的随机检验等不可缺少的检测设备，拉力机夹具作为仪器的紧要构成部分，不同的材料需要不同的夹具，也是试验能否顺当进行及试验结果精准度高处与低处的一个紧要因素。

功能：本试验机接受直流伺服电机及调速系统一体化结构驱动同步带减速机构，经减速后带动丝杠副进行加载。

电气部分包括负荷测量系统和变形测量系统构成。

JLSYQ-6全自动绝缘油介电强度测试仪使用说明书扬州金力电气有限公司尊敬的用户：感谢您选用JLSYQ-6全自动绝缘油介电强度测试仪。

我们希望本仪器能使您的工作更加轻松愉快，使您在试验分析工作中得到办公自动化的感觉。

在使用仪器之前，请阅读本说明书，并按说明书对仪器进行操作和维护，以延长其使用寿命。

“只需轻轻一按，试验会自动完成”是本仪器的操作特点。

如您对本仪器感到满意，请告诉您的同行；如您对本仪器有不满意的地方，请拨打（0514）88773006告诉时刻为您服务的—扬州金力电气有限公司，本公司一定会使您满意！一、概述在电力系统、铁路系统及大型石油化工厂矿，企业都有大量的电气设备，其内部绝缘大都是充油绝缘型的，绝缘油的介电强度是必测的常规试验。

为适应市场需要，我公司依据国家标准GB/T507-2002、行标DL429.9-91以及最新的电力行业标准DL/T846.7-2004自行研发、生产了系列绝缘油介电强度测定仪。

本仪器以单片微计算机为核心，实现了测试全部自动化，测量精度高，极大的提高了工作效率，同时也大大减轻了工作人员的劳动强度。

二、主要功能及特点1、本仪器采用微处理器，六杯一体，自动完成升压、保持、搅拌、静放、计算、打印等操作，可在0～80KV范围内进行油循环耐压试验。

2、大屏幕液晶显示，汉字菜单提示。

3、本仪器操作简单，操作人员只需进行简单的设置，仪器将会按照设定自动完成1-6个油样的耐压试验。

每个油样，每次击穿电压值和轮回次数会自动存储，试验完成后，热敏打印机可打印出各油样各次击穿电压值和平均值。

4、掉电保持，可存储100个实验结果，并可显示当前环境温度和湿度。

5、采用单片机控制进行匀速升压，电压频率准确到50HZ，使得整个过程便于控制。

6、具有过压、过流、限位等保护，以保障操作人员的安全。

7、具有温度测量显示功能以及系统时钟显示。

8、标准RS232接口，可与计算机通信。

三、主要技术指标1、输出电压：0～80KV（可选）2、电压畸变率：＜3%3、升压速度：2.0～3.5KV/S（可调）4、静放时间：15分（可调）5、 升压间隔：5分（可调）6、 升压次数：1～6次7、 升压器容量：1．5KVA8、 测量精度：±3%9、 电源电压：AC220V ±10% 50Hz ±1 Hz 10、 功率：200W11、 适用温度：0℃～45℃ 12、 适用湿度：＜75%RH 13、 外形尺寸：585×390×410 四、面板说明① 热敏打印机--打印测试结果② 液晶显示器--显示菜单和各种提示及测试结果 ③ 操作按键--在按下“选择”键后，按此键可递增设置数值 --在按下“选择”键后，按此键可递减设置数值 选择--用此键可选择各项功能，反白光标所在项为被选中项 确认--功能执行键 返回--退出操作界面④ 杯位指示灯—灯亮表示该号杯为当前测试杯位 ⑤ 电源开关与指示五、操作方法1、测试前准备①本仪器在使用前应首先将接地端子（设备的右侧面）与地线联接牢固，要特别注意不能虚接。

DCJY-80SI绝缘油介电强度测试仪信息来源：http://kv-kva/328/index.html操作说明1、准备开机将仪器的电源开关置于“关”的位置，可靠接好地线。

用专用的电源线将交流220V接至仪器，合上电源开关，仪器的显示屏（LCD）显示仪器型号、名称、编号、软件版本、系统时间等基本信息。

2. 数据设置2.1设置系统时间2.1.1开机LOGO，按【菜单】键进入主菜单。

主菜单有三个选项：“设置系统时间”“设置测试参数”和“数据管理”。

2.1.2按【↑】键和【↓】键移动阴影光标到“设置系统时间”，再按【确认】键进入时间设置界面。

2.1.3按【←】键和【→】键移动阴影光标到需要更改的数据，按【↑】键和【↓】更改数据。

例：按【→】键移动阴影光标到月份的位置。

2.1.4按一下【↑】键可将月份更改为03。

2.1.5更改完毕按【确认】键保存数据并返回上一级菜单。

2.2设置测试模式2.2.1开机LOGO，按【菜单】键进入主菜单。

主菜单有三个选项：“设置系统时间”“设置测试参数”和“数据管理”。

2.2.2按【↑】键和【↓】键移动阴影光标到“设置测试参数”，再按【确认】键进入设置测试参数界面。

按【确定】键显示2.2.3按【←】键和【→】键移动阴影光标到需要更改的数据，按【↑】键和【↓】更改数据。

1）如要选择“国标模式”，可按【←】键和【→】键移动阴影光标到“测试模式”行，按【↑】键和【↓】选择“国标”。

2）如要选择“自定义模式”，可用【↑】键和【↓】键移动阴影光标到“自定义”，再按【确认】键进入“自定义模式”的修改状态。

3）按【←】键和【→】键移动阴影光标到需要更改的数据，按【↑】键和【↓】更改数据。

注：可更改的数据有：最高电压（一般不需更改）、静置时间、等待时间、搅拌时间、试验次数等。

其中最高电压的设置范围为5kV到额定最高压，且最小调节幅度为1kV。

如80kV的试油机的最高电压只能设置为5kV到80kV；100kV试油机则最高电压只能设置为5kV到100kV；静置时间设置范围0~ 999秒；等待时间设置范围0~ 999秒；搅拌时间设置范围0~ 999秒；试验次数设置范围1 ~ 6次。

绝缘油介电强度检测仪的使用方法绝缘油介电强度检测仪是一种测试绝缘油介电强度的专用仪器设备。

通过测量绝缘油中的介电常数和介电损耗因数，对绝缘油中的杂质、水分、气体等指标进行评价和测试，以确保设备的安全运行，保护电力设备的绝缘性能，维护电网的稳定运行。

一、使用前准备绝缘油介电强度检测仪的使用需要充分以下条件：1.已经备好绝缘油介电强度检测仪的设备，同时设备需要进行维护保养，确保仪器处于正常使用状态；2.准备要测试的绝缘油，确保绝缘油中没有杂质、水分、气体等污染物；3.确保测试环境干燥、干净，并可供应电源和接地条件；4.使用前应认真阅读使用说明书，了解使用方法和安全注意事项。

二、操作步骤1.连接电源和接地。

将绝缘油介电强度检测仪的电源接入220V电源插座，同时将接地端与接地线连接，确保仪器与测试环境的接地电势相同。

2.启动仪器，进行预热。

按下仪器面板的“开机”按钮，待仪器准备就绪后进行预热。

预热时间一般需要30分钟左右，依据不同型号的绝缘油介电强度检测仪，时间可能会有所不同。

3.准备样品并设置测试参数。

将准备好的绝缘油样品加注到仪器中，并依据测试要求设置好测试参数，包括介电强度标准、测量频率、测量电压等参数。

参数设置应依据实在测试要求进行调整。

4.开始测试。

按下仪器面板上对应的测试按钮开始测试。

测试过程中，应依据仪器提示渐渐进行下一步操作，确保测试结果精准且牢靠。

5.测试结束及数据处理。

测试完成后，依据测试结果进行数据处理，并依据实际需要取得测试结果报告。

同时，对仪器进行清洁和维护保养，以确保设备的正常使用寿命和性能。

三、使用注意事项1.使用前需要进行充分的保养和维护，确保仪器处于正常工作状态；2.进行测试时需要注意安全，避开触电和其他不安全事故的发生；3.在使用过程中，应保证测试环境的干燥、干净，避开外部电磁干扰和污染物对测试结果的影响；4.对测试结果进行分析和处理时应依据实际情况进行调整和修正，以确保结果的精准性和牢靠性；5.使用过程中，应注意仪器的维护保养和日常清洁，适时更换损坏的部件和配件，以保证仪器的长期稳定运行。

专利名称：绝缘油介电强度测试仪专利类型：发明专利
发明人：毕青春,殷桂宏
申请号：CN201010215346.5申请日：20100630
公开号：CN102313845A
公开日：
20120111
专利内容由知识产权出版社提供
摘要：本发明涉及一种绝缘油介电强度测试仪。

包括有微机控制装置、打印装置、显示装置、自动搅拌装置、调压装置，所述的自动搅拌装置、打印装置、显示装置、调压装置共同受微机控制装置控制。

本仪器测试全过程由单片微机控制，抗干扰性能提高，完全克服了现有测定器易受高压击穿干扰的弊病，本发明大大提高了工作效率，测试安全、可靠、准确、稳定，降低了击穿油液所需的能量，从而降低了整机的能耗、体积和重量；同时测试过程中不需要清理电极，微机自动控制搅拌，测试读数稳定准确。

申请人：扬州华电电气有限公司
地址：225828 江苏省扬州市宝应县柳堡镇人民东路102号
国籍：CN
代理机构：北京连和连知识产权代理有限公司
代理人：李海燕
更多信息请下载全文后查看。