HTN501 NC010 is a 30% glass reinforced, flame retardant, lubricated high performance polyamide HTN501 NC010DuPont ™ Zytel ®HTNhigh performance polyamide resinZytel ®ValueDAM50%RHIdentification Part Marking Code ISO 11469>PA6T/XT-GF35FR< Part Marking Code SAE J1344>PPA-GF35FR<Mechanical Stress at Break ISO 527MPa (kpsi)165 (24) Strain at Break ISO 527% 1.6 Tensile Modulus ISO 527MPa (kpsi)13000 (1885) Shear Strength ASTM D 732MPa (kpsi)64 (9.3)70 (10) Flexural Modulus ISO 178MPa (kpsi)12000 (1740)12000 (1740) Flexural Strength ISO 178MPa (kpsi)250 (36)235 (34)Compressive Strength ASTM D 695MPa (kpsi)293 (42.6) Compressive ModulusASTM D 695MPa (kpsi)3580 (520)Notched Charpy Impact Strength ISO 179/1eAkJ/m2-30°C (-22°F)13 23°C (73°F)11 Unnotched Charpy Impact Strength ISO 179/1eUkJ/m2-30°C (-22°F)30 23°C (73°F)40Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3Zytel ®resin. It is also a PPA resin.PropertyTest Method UnitsDuring molding, use proper protective equipment and adequate ventilation. Avoid exposure to fumes and limit the hold up time and temperature of the resin in the machine. Purge degraded resin carefully with HDPE.Zytel®ValueDAM50%RHThermalDeflection Temperature ISO 75-1/-2 °C (°F)0.45MPa 270 (518) 1.80MPa260 (500)Melting Temperature ISO 11357-1/-3 °C (°F)10°C/min, First Heat 300 (574)CLTE, Parallel ISO 11359-1/-2E-4/C (E-4/F)-40 - 23°C (-40 - 73°F)0.20 (0.11) 23 - 55°C (73 - 130°F)0.18 (0.10) 55 - 125°C (131 - 257°F)0.18 (0.10)CLTE, Normal ISO 11359-1/-2E-4/C (E-4/F)-40 - 23°C (-40 - 73°F)0.46 (0.26) 23 - 55°C (73 - 130°F)0.50 (0.28) 55 - 125°C (131 - 257°F)0.60 (0.33)Glass Transition Temperature DMA °C (°F)140 (284)90 (194)Electrical Surface Resistivity IEC 60093ohm 1E13 Volume Resistivity IEC 60093ohm m >1E131E13 Electric Strength IEC 60243-1kV/mm (V/mil)1.0mm34 (863)34 (863)Relative Permittivity IEC 602501E2 Hz 3.9 1E3 Hz 3.8 1E6 Hz 3.6Dissipation Factor IEC 60250E-41E2 Hz 80 1E3 Hz 130 1E6 Hz 150Arc Resistance ASTM D 495s 80 CTIIEC 60112V 525Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3PropertyTest Method UnitsHTN501 NC010Zytel®ValueDAM50%RHFlammabilityFlammability Classification UL940.81mm V-0Oxygen Index ISO 4589-1/-2%37Hot Wire Ignition UL 746As0.81mm >150 1.5mm >150 3.0mm>150Temperature Index RTI, Electrical UL 746B°C0.81mm 150 1.5mm 150 3.0mm 150RTI, Impact UL 746B°C0.81mm 120 1.5mm 125 3.0mm 130RTI, Strength UL 746B°C0.81mm 130 1.5mm 130 3.0mm150Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3PropertyTest Method UnitsHTN501 NC010Zytel®ValueDAM 50%RHOther DensityISO 1183kg/m 3 (g/cm 3)1680 (1.68)Hardness, Rockwell ASTM D 785Scale M 108 Scale R 124Taber AbrasionASTM D 1044mgCS-17 Wheel, 1kg, 1000 cycles 57Water Absorption ASTM D 570%Immersion 24h 0.25Molding Shrinkage ISO 294-4%Normal, 2.0mm 0.5 Parallel, 2.0mm 0.2ProcessingMelt Temperature Range °C (°F)320-330 (610-625) Mold Temperature Range °C (°F)140-160 (280-320)Drying Time, Dehumidified Dryer h 6-8 Drying Temperature°C (°F)100 (210) Processing Moisture Content%<0.10Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3PropertyTest Method Units HTN501 NC010。
Technical Data SheetLOCTITE®6205月2004产品说明®LOCTITE®620主要适用于圆柱型装配件的粘接.该产品在隔绝氧气的金属密封面间固化，可以防止由于震动或冲击而引起的松动或泄漏.典型用途包括填充紧密配合的压配合件，键沟和花键之间的空隙；装配轴承和衬套，并使压配合键固持强度更高.特别适合用于耐温条件必须达到200°C的情况.固化前的材料特性比重@ 25°C1,16闪点 -见MSDS粘度， Brookfield -RVT, 25°C,mPa·s(cP):转子 5, 转速20rpm5000-12000LMS粘度，EN12092 -MV,25°C,后180s,mPa·s(cP):剪切速度129s-11200-2400典型固化特性固化速度与基材的关系固化速度取决于所用的基材.以下图表显示的是按照ISO10123方法测试，钢制轴和套剪切强度与固化时间的关系以及与其它不同材料之间的比较测试.钢材上的强度固化时间1007550251min5min10min30min1h3h6h24h72h钢铝材重铬酸锌固化速度与间隙的关系固化速度取决于间隙的大小.下图显示在钢制轴和套上，在不同的间隙，剪切强度和时间的关系。
测试标准为ISO10123方法测试.钢材上的强度固化时间1007550251min5min10min30min1h3h6h24h72h.15mm.2mm.5mm固化速度与温度的关系固化速度取决于温度.以下图表显示的是按照ISO10123方法测试，钢制轴和套剪切强度与固化时间及不同温度条件下的测试.钢材上的强度固化时间1007550251min5min10min30min1h3h6h24h72h4°C22°C5°C固化速度与促进剂的关系当固化速度很慢或者间隙较大时，应用促进剂可以加快固化速度.以下图表显示的是按照ISO10123方法测试，620在使用活化剂7471或7649的重铬酸锌钢销和钢套上，在不同固化时间下的破坏强度.钢材上的强度固化时间1007550251min5min10min30min1h3h6h24h72h促进剂7471™促进剂 7649™无促进剂固化后材料典型性能物理性能:热膨胀系数,ISO 11359-2,K -180×10-6 导热系数, ISO 8302, W/(m·K)0,1比热,kJ/(kg·K)0,3模量,断裂时,ISO 37,%<1固化后材料特性胶粘剂性能后24小时 @22°C压剪切强度， ISO 10123:钢制轴和套N/mm² ≥17,2LMS (psi) (2495)固化24小时 @22°C之后进行固化24小时@ 177°C,测试温度@22°C压剪切强度， ISO 10123:钢制轴和套 N/mm² ≥24,1LMS(psi) (3495)典型环境抵抗性能固化1周 @22°C压剪切强度， ISO 10123:钢制轴和套热强度在测试温度下进行强度测试% 强度温度（°C ）1251007550250050100150200250老化强度在测试温度下进行老化,在22°C 进行测试% 初始强度时间2001501005000100500100030005000120 °C150 °C180 °C热老化在特定温度下老化，在22°C下测试% 初始强度时间20015010050100500100030005000120 °C150 °C180 °C耐化学品/溶剂测试在下列条件下进行老化，在22°C 进行测试.初始粘结强度的剩有率%环境°C 100h 500h 1000h 机油(MIL-L-46152)125100100100无铅汽油22959595制动液2210010010050/50乙二醇/水87958080乙醇2210010075丙酮22959595注意事项本产品不宜在纯氧与（或富）富氧氧环境中使用，不能作为氯气或其它强氧化性物质的密封材料使用。
杜邦PBT HR5330HF本色NC010黑色BK503物性表：产品提供久隆塑胶原料tEL134********CRASTIN®HR5330HF是30％的玻璃纤维增强，高流量（HF)，抗水解（HR）树脂。
耐冲击性及强度出色的平衡性能。
添加剂：润滑剂,、脱模助剂。
特征：可焊、耐化学试剂、水解稳定。
应用：汽车,电子电气。
熔体体积流动速度(MVR)8cm³/10min ISO1133温度250℃ISO1133载荷2.16kg ISO1133模塑收缩率(平行)0.3%ISO294-4,2577模塑收缩率(垂直) 1.0%ISO294-4,2577拉伸模量8500MPa ISO527-1/-2断裂应力110MPa ISO527-1/-2断裂伸长率 2.9%ISO527-1/-2无缺口简支梁冲击强度(+23°C)75kJ/m²ISO179/1eU简支梁缺口冲击强度(+23°C)15kJ/m²ISO179/1eA简支梁缺口冲击强度(-30°C)12kJ/m²ISO179/1eA熔融温度(10°C/min)225°C ISO11357-1/-3热变形温度(1.80MPa)205°C ISO75-1/-2热变形温度(0.45MPa)220°C ISO75-1/-2维卡软化温度(50°C/h50N)215°C ISO306线性热膨胀系数(平行)21E-6/K ISO11359-1/-2线性热膨胀系数(垂直)85E-6/K ISO11359-1/-21.5mm名义厚度时的燃烧性HB class IEC60695-11-10测试用试样的厚度 1.5mm IEC60695-11-10吸水性0.35%类似ISO62吸湿性0.15%类似ISO62密度1500kg/m³ISO1183。
