下载文档原格式
Maximum choice of features in a high performance packageFlame Detector Series40/40 UV/IR Spectrex offers two versions of the new 40/40 Series UV/IR Flame Detectors:Model 40/40L (& LB) provides a combination of UV and IR sensors, where the IR sensor operates at a wavelength of 2.5-3.0 µm, and can detect hydrocarbon-based fuel and gas fires, hydroxyl and hydrogen fires, as well as metal and inorganic fires.Model 40/40L4 (& L4B) is identical to the 40/40L except that the IR sensor works at a wavelength of 4.5 µm and is only suitable for hydrocarbon-based fires.The UV/IR flame detector senses radiant energy in the short wave section of both the ultraviolet and infrared portions of the electromagnetic spectrum. The signals from both sensors are analyzed for frequency, intensity and duration.Simultaneous detection of radiant energy in both the UV and IR sensors triggers an alarm signal.The UV sensor incorporates a special logic circuit that helps prevent false alarms caused by solar radiation.•UV/IR Dual-Sensor•High-Speed Response - 150 msec Response to Saturated Signal•Solar blind•Automatic Built-In-Test (BIT)* and Manual - to assure continued reliable operation•Heated window - for operation in harsh weather conditions (snow, ice, condensation)•Multiple output options for maximum flexibility and compatibility - Relays (3) for Alarm, Fault and Auxiliary - 0-20mA (stepped)- HART Protocol for maintenance and asset management - RS-485, Modbus Compatible•High Reliability - MTBF - minimum 150,000 hours•Approved to Safety Integrity Level 2 (SIL2 – TUV)•5-Year Warranty•User Programmable via HART or RS-485•Ex approved for Zone 1 hazardous area location - ATEX - IECEx - FM - CSA•3rd party Performance Tested - EN54-10 (LPCB)- FM3260 (FM)*option 40/40M 40/40I 40/40R40/40L-LB 40/40L4-L4B 40/40U-UB Offshore Oil & Gas installations Onshore Oil & Gas installations and pipelines Chemical plants Petrochemicals plants Storage Tank farms Aircraft hangars Power Generation facilities Pharmaceutical IndustryPrinting Industry Warehouses Automotive Industry Explosives & Munitions Waste Disposal facilities Aerospace Industry Paint, Polymer and Glue processes Tel 1800 999 902 Fax 1800 999 903GasTech Australia Pty LtdWangara Western Australia 606524 Baretta RdRelays Alarm, Fault and Auxiliary SPST volt-free contacts rated 5A at 30 VDC or 250 VAC.0-20mA (stepped)Sink (source option) configuration Fault: 0 +1mA IR:8mA ± 5%Alarm: 20mA ± 5%BIT Fault: 2mA ± 10%UV:12mA ± 5%Resistance Loop:100-600 ΩNormal:4mA ± 10%Warning:16mA ± 5%HART Protocol HART communication on the 0-20mA analog current (FSK) - used for maintenance, configuration changes and asset managementRS-485 RS-485 Modbus compatible communication link that can be used in computer controlled installationsDS-F-40/40 UV/IR, November 2008Fire Simulator 20/20-311Weather Protector 777163Laser Pointer 777166Tilt Mount 40/40-003Air Shield 777161(Detector area coverage)Materials - Stainless Steel 316L with electro polish finish Enclosure options - Heavy duty copper free aluminum (less than 1%), red epoxy enamel finishMounting Stainless Steel 316L with electro polish finishDimensionsDetector 3.5" x 4.5" x 6.1" (90 x 114 x 156 mm)Weight Detector (St.St.) 5.5 lb (2.5 kg) Detector, aluminum 2.5 lb (1.2 kg) Tilt mount 2.2 lb (1.0 kg)Environmental Standards Meets MIL-STD-810C for Humidity, Salt & Fog, Vibration, Mechanical Shock, High Temp, Low TempWater and Dust IP66 and IP67 per EN60529, NEMA 250 6PHazardous Area ATEX and IECExEx II 2 GD,Ex de IIB+H2 T5 (-55ºC to + 75ºC)Ex de IIB+H2 T4 (-55ºC to + 85ºC)Ex tD A21 IP66/X7 T 95ºC Ex tD A21 IP66/X7 T 105ºCFM / CSA Class I Div. 1, Groups B, C & D Class II/III Div. 1, Groups E, F & G Performance EN54-10 (LPCB)FM-3260 (FM)Reliability IEC61508 - SIL2 (TUV)Operating Voltage 24 VDC nominal (18-32 VDC)Power Consumption Standby:Max. 100mA (150mA with heated window)Alarm:Max. 150mA (200mA with heated window)Cable Entries 2 x 3/4" - 14NPT conduits or 2 x M25 x 1.5 mm ISOWiring 12 - 22AWG (2.5mm 2 - 0.3mm 2)Electrical Input Protection According to MIL-STD-1275BElectromagnetic Compatibility EMI/RFI protected to EN50130-4Electrical Interface The detector includes twelve (12) terminals with five (5) wiring options (factory set)Spectral Response40/40L–LB:UV: 0.185 - 0.260 µm; IR: 2.5-3.0 µm 40/40L4–L4B:UV: 0.185 - 0.260 µm; IR: 4.4-4.6 µm Detection Range Fuel ft / m Fuel ft / m Fuel ft / m (at highest Sensitivity Setting n-Heptane 50 / 15Ethanol 95%25 / 7.5LPG *16/ 5for 1ft 2 (0.1m 2) pan fire)Gasoline 50 / 15Methanol 25 /7.5Polypropylene Pellets 13/ 4Diesel Fuel 37 / 11IPA (Isopropyl Alcohol)25 / 7.5Office Paper 16/ 5JP537 / 11Hydrogen**16 / 5* 20" (0.5m) high, 8" (0.2m) width Kerosene 37 / 11Methane*16 / 5plume fire ** 40/40L/LB onlyResponse Time Typically 5 seconds. High speed 150 msec response to saturated signalAdjustable Time Delay Up to 30 secondsSensitivity Ranges 1 ft 2 (0.1m 2) n-heptane pan fire from 50 ft (15m)Field of View Horizontal 100º; Vertical 95ºBuilt-in-Test (BIT)Automatic (and Manual)Temperature Range Operating:-67°F to +167ºF (-55ºC to +75ºC)Option:-67ºF to +185ºF (-55ºC to +85ºC)Storage:-67ºF to +185ºF (-55ºC to +85ºC)Humidity Up to 95% non-condensing (withstands up to 100% RH for short periods)Heated Optics To eliminate condensation and icing on the windowTel 1800 999 902 Fax 1800 999 903GasTech Australia Pty Ltd Wangara Western Australia 606524 Baretta Rd。
Mobile USBSpinpoint M8U250GB 320GB 500GB 640GB 750GB 1TBModel HN-M250ABB HN-M320ABB HN-M500ABB HN-M640ABBHN-M750ABBHN-M101ABB Samsung Models FEATURES• Max. 500GB formatted capacity per disk • SilentSeek™ • TuMR/PMR head with FOD technology • NoiseGuard™• USB 3.0 Interface Support• Load/Unload Head Technology Capacity 1 250 ~ 750GB, 1TBTemperature InterfaceUSB 3.0 Operating 5 ~ 55 °C Buffer DRAM Size 28 MBNon-operating -40 ~ 70°C Rotational Speed5,400 RPM ClassHumidity (non-condensing) Operating 5-90 % Non-operating 5-95 %Average Seek time (typical)12 ms Linear Shock (1/2 sine pulse)Average Latency 5.6 ms Operating, 2ms 325 G Data Transfer RateNon-operating, 2ms 750 G Media to/from Bu er (Max.)145 MB/s Vibration (swept sine, 1/4 octave per minute) Bu er to/from Host (Max.)400 MB/sOperating 0.9 Grms Drive Ready Time (typical)34 secAltitude (relative to sea level) Operating -300 to 3000 m Non-operating -400 to 15000 mNon-recoverable Read Error 1 sector in 1014bitsControlled Ramp Load/Unload 600,000Height 9.5 mm Idle2.4 Bel Width 69.85 mm Performance Seek 2.6 BelLength104 mm Weight (max.)107 gVoltage+5V±5%* Note : Design and speci cations are subject to change without prior notice.Spin-up Current (Max.) 750 mA 1 1MB = 1,000,000 Bytes, 1GB = 1,000,000,000 BytesSeek (AVG)43.0 W Accessible capacity may vary as some OS uses binary numbering system Read/Write (AVG)3.2 W for reported capacityLow Power Idle (AVG) 1.8 W 2 A small portion of the 8MB bu er memory is reserved for rmware use Standby (AVG) 1.4 W 3 Power-On to Drive Ready Sleep (AVG)1.4 W4 30% duty cycle, random seek2.5" HDD product speci cation Rev2.1Match with product manual Rev2POWER REQUIREMENTS ACOUSTICS Capacity DRIVE CONFIGURATION ENVIRONMENTAL SPECIFICATIONS PERFORMANCE SPECIFICATIONS RELIABILITY SPECIFICATIONS PHYSICAL DIMENSIONModel8 MB8 MB ST 250LM003ST320LM005ST500LM014ST640LM019 ST750LM023ST1000LM025 Seagate Models。
输出手册版本历史版本号说明日期1.0 初版2019-6-171.1 1. LRC频率：min（30->27），max（50->62）2. ADC特性更新： fADC-40℃≤ Trange ≤ 85℃，fADC≤14MHz，支持电压范围2.65≤ VDDA ≤5.5V；-40℃≤ Trange ≤ 105℃，fADC≤14MHz，支持电压范围2.7≤ VDDA ≤5.5V；-40℃≤ Trange ≤ 105℃，fADC≤12MHz，支持电压范围2.4≤ VDDA ≤5.5V；进入校准模式，fADC≤12MHz。
进入正常转换模式，fADC≤14MHz。
支持：-40℃≤ Trange ≤ 105℃和电压范围2.4≤ VDDA ≤5.5V；3. ADC特性更新：VDDA=2.4V时，Offset和ERR Gain更新2020-6-31.2 1.增加G6U6版本相关信息2020-6-191.3 1.更新温度传感器线性度参数，区分不同温度范围2020-8-262/56文件编号：CS-QR-YF-054A02目录输出手册版本历史 (2)目录 (3)1介绍 (5)2功能 (6)3器件一览 (8)4引脚描述 (10)4.1LQFP48 (10)4.2LQFP32 (10)4.3QFN28L (11)4.4TSSOP20 (11)4.5引脚描述 (12)5I/O 复用 (15)5.1PA口复用功能 (15)5.2PB口复用功能 (16)6存储器 (17)7功能描述 (21)7.1ARM®C ORTEX®-M0内核 (21)7.2存储器 (21)7.3时钟 (21)7.4工作环境 (23)7.4.1工作电压 (23)7.5启动模式 (23)7.6电源管理 (23)7.6.1低功耗模式 (23)7.6.2RTC和备用寄存器的电源电压VBAT (23)7.6.3上电复位/掉电复位(POR/PDR) (23)7.6.4低电压复位模块(LVD) (24)7.7通用输入输出端口(I/O) (24)7.8模数转换器(ADC) (24)7.8.1温度传感器(TS) (24)7.8.2内部参考电压 (24)7.8.3VBAT监测 (25)7.9定时器 (25)7.9.1高级定时器 (TIM1) (25)7.9.2通用定时器 (TIM3, 14, 15,16, 17) (25)7.9.3基本定时器(TIM6) (26)7.9.4独立看门狗定时器(FWDT) (26)7.9.5窗看门狗定时器(WWDT) (26)7.9.6滴答定时器(SysTick) (26)7.10直接内存存取(DMA) (26)3/56文件编号：CS-QR-YF-054A027.11中断和事件 (26)7.12实时时钟(RTC)和备用寄存器 (26)7.13串行外设总线（SPI）/集成电路内置音频总线（I2S） (27)7.14通用同步异步收发器（USART） (27)7.15内置集成电路接口（I2C） (29)7.16循环冗余校验 (29)7.17串行调试端口(SWD-DP) (29)8电气特性 (30)8.1说明 (30)8.2绝对最大额定值 (31)8.3工作条件 (31)8.4I/O端口特性 (32)8.5低功耗模式唤醒时间 (33)8.6RC振荡特性 (33)8.7晶振特性 (34)8.8外部时钟特性 (36)8.9PLL特性 (36)8.10功耗 (37)8.11内部参考电压特性 (38)8.12ADC特性 (38)8.13温度传感器特性 (39)8.14VBAT监测器特性 (39)8.15F LASH 特性 (39)8.16定时器特性 (40)8.17SPI/I2S特性 (40)8.18I2C特性 (44)8.19ESD特性 (44)9封装信息 (46)9.1LQFP48 (46)9.2LQFP32 (48)9.3QFN28L (49)9.4TSSOP20 (51)10订货信息 (52)11勘误表 (53)12缩略语 (54)13销售和服务 (56)4/56文件编号：CS-QR-YF-054A021介绍CS32F030系列微控制器采用高性能的32位ARM® Cortex®-M0 内核，嵌入高达64Kbytes flash和8Kbytes SRAM，最高工作频率48MHz。
BIS-1280A40 整机说明书声明除列明随产品配置的配件外，本手册包含的内容并不代表本公司的承诺，本公司保留对此手册更改的权利，且不另行通知。
对于任何因安装、使用不当而导致的直接、间接、有意或无意的损坏及隐患概不负责。
订购产品前，请向经销商详细了解产品性能是否符合您的需求。
NORCO 是深圳华北工控股份有限公司的注册商标。
本手册所涉及到的其他商标，其所有权为相应的产品厂家所拥有。
本手册内容受版权保护，版权所有。
未经许可，不得以机械的、电子的或其它任何方式进行复制。
温馨提示1．产品使用前，务必仔细阅读产品说明书。
2．对未准备安装的板卡，应将其保存在防静电保护袋中。
3．在从包装袋中拿板卡前，应将手先置于接地金属物体上一会儿，以释放身体及手中的静电。
4．在拿板卡时，需佩戴静电保护手套，并且应该养成只触及其边缘部分的习惯。
5．主板与电源连接时，请确认电源电压。
6．为避免人体被电击或产品被损坏，在每次对主板、板卡进行拔插或重新配置时，须先关闭交流电源或将交流电源线从电源插座中拔掉。
7．在对板卡进行搬动前，先将交流电源线从电源插座中拔掉。
8．当您需连接或拔除任何设备前，须确定所有的电源线事先已被拔掉。
9．为避免频繁开关机对产品造成不必要的损伤，关机后，应至少等待30秒后再开机。
10．设备在使用过程中出现异常情况，请找专业人员处理。
11．此为A级产品，在生活环境中，该产品可能会造成无线电干扰。
在这种情况下，可能需要用户对其干扰采取切实可行的措施。
目录第一章产品介绍 (1)1.1 硬件规格 (1)第二章安装说明 (2)2.1 右侧图 (4)2.2 前视图 (4)2.3 后视图 (4)第三章硬件功能 (3)3.1 外部接口指示图 (3)3.2 SOMB-7007 V1.0 (3)3.3 安装步骤 (4)3.4 跳线功能设置 (5)3.4.1 跳线功能设置（J1，J2，J3，J4，J5，J6，J7，J8，J9，J10，J11，J12） (5)3.5 接口说明 (6)3.5.1 串口（J17） (6)3.5.2 SATA接口（SATA，J27） (9)3.5.3USB接口（USB12_DEBUG，OTG） (10)3.5.4 以太网接口（LAN1_2） (10)3.5.5 显示接口（HDMI） (10)3.5.6 接口（J13，J26） (11)3.5.7 电源接口（PWRIN1，PWRIN2，PWROUT） (13)3.5.8 DI和DO接口（J14，J16，J18，J9） (13)3.5.9 扩展接口 (17)4.1 linux 系统.............................................................................................................. - 0 -4.1.1HDMI部分 .................................................................................................... - 0 -4.1.2 USB部分..................................................................................................... - 0 -4.1.3 COM部分.................................................................................................... - 0 -4.1.4 TF卡部分 .................................................................................................... - 0 -4.1.7 3G/4G部分.................................................................................................. - 0 -4.1.8 以太网部分.................................................................................................. - 1 -4.1.9 DI部分......................................................................................................... - 1 -4.1.11 DO部分 ..................................................................................................... - 1 -4.1.12 12v电源控制部分.................................................................................... - 1 -5.1 ASL-572A V1.0 ...................................................................................................... - 1 -5.2 安装步骤 ............................................................................................................... - 2 -5.3 接口说明 ............................................................................................................... - 2 -5.3.1 接口（J1，J2） .......................................................................................... - 3 -5.3.2 SIM插槽...................................................................................................... - 4 -5.3.3 SD插槽 ....................................................................................................... - 4 -5.3.4 复位按键（RSTSW）.................................................................................. - 4 -5.3.5 电源按键（PWRSW） ................................................................................ - 5 -5.3.6 MINIPCIE接口............................................................................................. - 5 -附录22附一：术语表 (22)装箱清单非常感谢您购买华北工控产品，在打开包装箱后请首先依据装箱清单检查配件，若发现物件有所损坏、或是有任何配件短缺的情况，请尽快与您的经销商联络。
PALM产品库SPTVisor Prism ROMRAM中文输入法显示规格显示屏分辨率电池类型附件与选件规格的连接座及连接线、Clié处理器类型处理器主频显示屏内存通讯端口Modem电源Clié 插槽通讯接口显示屏类型色彩及分辨率多媒体配置电源类型小时体积与重量附件清单触控笔。
随机软件其他处理器型号WorkpadWorkpad输入方式显示屏背光内存通讯端口程序互传；传输电源外形尺寸产品重量随机附件图片相关参数处理器型号处理器主频操作系统ROMRAMClié(1. Memory: 8 MB RAMProcessor: 33 MHz Motorola Dragonball VZ FlashROM: Yes (4 MB)Expansion slot: SD/MMC (2x)Interfaces/Wireless: USB, Infrared Power supply: 3 batteries (AA/Mignon) Synchronisation: Docking cable (USB) Weight: 910 gSize: 31,4 x 23,5 x 4,8 cmSpecials: Keyboard, notebook-design处理器内存操作系统扩展插槽Clié Clié Clié扩展插槽电池可更换标配电池容量外接电源网络类型和弦铃声天线位置免提通话震动功能Clié CliéClié ROM触摸显示屏显示屏类型显示屏尺寸光扩展插槽电池可更换标配电池容量Clié图片CliéCliéCliéClié Palm Zire 71Clié Clié(2. iQue Xplore TreoCliéHunetec H500 Palm Zire 21Clié CliéClié CliéCliéXplore Palm Zire 31 Palm Zire 72iQue Clié XploreTungsten T5 处理器类型处理器主频操作系统RAM扩展槽PDA数据传输接口显示屏颜色Treo 处理器：通话时间：待机时间：WAP标准配置：内存容量：多媒体卡扩展：扩充卡插槽Fossil Wrist PDA Garmin iQue 3600aPalm Tungsten E2 处理器主频显示屏ram电池外形尺寸rom通讯端口各类接口产品重量Garmin iQue 3000。
Congratulations on your newrechargeable hearing aidThis booklet will guide you through the usage of Oticon Opn™ miniRITE rechargeable solution and ensure that you get off to a good start with your new product.It is highly recommended that you read the instructions booklet provided with the Oticon Opn™ miniRITE hearing aid, as well as the instructions booklet provided with the rechargeable box.For easy access to instructional videos, scan the QR codes on each page with your smartphone, or visit the support page onwww.oticon.global/rechargeableWe wish you all the best with your new rechargeable solution. We hope you will enjoy the convenience of charging, and rest assured that you will never be out of power since you can always use normal batteries as a back-up solution.Your Oticon Opn miniRITE rechargeable hearing aid 6How to insert the rechargeable batteries 8Expected battery performance 10How to use the rechargeable batteries 12Care and maintenance13How to charge your hearing aids 14LED indications 15Troubleshooting guide165 tips to get the best from your rechargeable Oticon Opn hearing aids 18Table of contents67Your Oticon Opn miniRITE rechargeable hearing aidbattery draweron/off switch(60 shown)WHAT IT ISNOTEOpen the battery drawer if you want to turn off your hearing aid.89 How to insert the rechargeable batteriesNOTEOticon Opn miniRITE. Do not place hearings aids with disposablebatteries in the charger.1. O pen the batterydrawer2. P lace the ZPowerrechargeablebattery inside thebattery drawer (goldside facing upwards)3. C lose the batterydrawer1011Daily hours of usage depend on level of hearing loss and lifestyle.Based on a minimum uninterrupted charge of 7 hoursNo streaming90 minutes of iPhone® streaming4 hours of TV and 1 hour of iPhone streaming18-19.516-1715-16hours hours hours Apple, the Apple logo, iPhone, iPad, iPod touch, and Apple Watch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.Battery life examples given a fully charged batteryExpected battery performanceIf the battery is fully charged for 7 uninterrupted hours, the ZPower solution is expected to provide a full day of operating time. The expected day-to-day battery life will vary depending on the degree of use.• A full 19-hour day of battery use without streaming.• 16-17 hours of use based on 90 minutes of iPhone streaming activity in addition to traditional use. • 15-16 hours of use for traditional hearing aid usage in addition to 4 hours of television and one hour of streaming from iPhone.If used daily, the rechargeable ZPower silver-zinc batteries will last for roughly a year before they will need to be replaced.How to use the rechargeable batteriesProper use will help to extend the life of your batteries.• C harge the hearing aids before wearing them. The recommended charge time is 7 uninterrupted hours.• C harge the hearing aids at temperatures between 50°F (10°C)and 104°F (40°C).• D on’t place the hearing aids in the charger if the charger is unplugged; this will drain the batteries.• I f you don’t intend to use your hearing aids for several days, remove the batteries.• D on’t force the battery to operate after the HA is turned off, by opening and closing the battery drawer.• Y our batteries should last for approximately one year.Contact your hearing care professional if you need new batteries.Care and maintenance• Clean as needed.• R emove debris or build-up from hearing aids and the charger dock inlays with soft tissue or Oticon brush.• Do not apply rubbing alcohol or other chemical substances.• Testing confirmed moisture and swelling should not be an issue.• D on’t store the rechargeable silver zinc batteries together with coins and metal pieces, when removed from the hearing aids.• W ipe off any moisture on the hearing aids or charging dock before charging using a soft tissue or Oticon brush.121315 How to charge your hearing aidsLED indications• Blinking green light when charging• S olid green light when completelycharged• I f red light is displayed, see the troubleshooting guide on next page.NOTEOnce you take the hearing aids out of thecharger dock, they will automatically turn on.Plug the USB into the charger,then plug the adapter into thewall. Once powered, the chargerLED will shortly blink green.Place your hearing aids into thecharger dock. You will see a greenlight blinking when the hearingaids start charging.141617Troubleshooting guideNOTEIf none of the above solutions work visit our support site www.oticon.global/rechargeable or consult your hearing care professional for assistance.18182931U K / 2017.12.215 tips to get the best from your rechargeable Oticon Opn hearing aids1. C harging: Always fully charge the batteries, until the light in the charging dock is solid green – it takes approximately 7 hours.2. O ut of power: If the batteries are drained and the hearing aids have switched off, never try to get more use by opening and closing the drawer. Either:a. Place the hearing aids in the charging dock and ensure it is powered on.b. I nsert disposable batteries and keep the rechargeable batteries safe for charging later. 3. N ot in use: If you are not using your hearing aids for an extended period of time, take the batteries out.Note: Avoid leaving the rechargeable batteries in the hearing aids with the battery drawers open. This will compromise battery life.4. H andling: Don’t keep the rechargeable batteries together with metal objects such as keys and coins.5. M aintenance: Wipe off any moisture on the hearing aids or charging dock before charging using a soft tissue. Do not use rubbing alcohol or other chemical substances.。
天电光电EMC 2016产品A40球泡灯参考设计Lightning EMC 2016LED A40 Bulb Reference Design目录Table of contents简介Introduction (1)灯具规格需求Define lighting requirements (2)设计目标Define design goals (2)整灯方案规划Estimate system efficiency (2)确定LED型号及数量Calculate the number of LED needed (3)散热方案设计Thermal requirements (4)驱动电源Driver (5)二次光学配件Secondary optics (6)样灯完成及测试结果Prototyping and test results (7)BOM表估算Bill of materials (8)结论Conclusion (9)简介本参考设计手册系统描述了如何应用天电光电EMC系列2016LED产品来制作A40球泡灯，可以替代40W传统白炽灯炮。
2016LED产品可以提供卓越的光电性能并大幅降低灯具系统成本。
所制作的球泡灯可广泛应用于各种室内应用，涵盖家居及商用照明应用等。
天电光电2016LED产品提供超高光通量及能量效率，是制作球泡灯的最佳LED光源之一。
同时，在T5或T8应用里也有非常大的优势。
IntroductionThis application note details the design of a 40-wattequivalent bulb replacement lamp using TDEMC 2016 LED. The 2016 LED offers industry-leading performance and reduces system cost sharply. LED bulb lamps are widely used in various indoor and outdoor applications, residential and commercial lighting applications. The high flux and efficacy offered by the TD EMC 2016 LED make it a particularly best candidate for use in a bulb lamp. Meanwhile, there is a great advantages in T5 or T8 tube applications.设计目标本次设计需要达到以下参数目标：整灯方案规划本次参考设计主要通过较低的温度、较高的光学效率、较高的电源效率来达到设计目标。
2”W x 4”L x 1.2”H 40W to 60W Output PowerUniversal 90-264VAC InputSingle, Dual & Triple Outputs from 3.3 to 48VDC High Efficiency to 88%3000V Isolation1U Compatible HeightModel Number Output Voltage Output Amps Efficiency %40W SINGLE OUTPUTOFM40-033 3.3VDC 6 74OFM40-050 5VDC 6 78OFM40-090 9VDC 4.45 82OFM40-120 12VDC 3.34 84OFM40-150 15VDC 2.67 85OFM40-240 24VDC 1.67 86OFM40-300 30VDC 1.33 86OFM40-360 36VDC 1.11 87OFM40-480 48VDC 0.83 8840W DUAL OUTPUT V1/V2 I1/I2 (Min.-Max.)OFM40D-01 5 / 12VDC 0.4 - 3.2 / 0.2 - 2A 77OFM40D-02 5 / 24VDC 0.4 - 3.2 / 0.2 - 1.2A 7840W TRIPLE OUTPUT V1/V2/V3 I1/I2/I3 (Min.-Max.)OFM40T-01 5/12/-5VDC 0.4 - 3/0.2 - 2/0 - 0.3A 75OFM40T-02 5/12/-12VDC 0.4 - 3/0.2 - 2/0 - 0.3A 75OFM40T-03 5/15/-15VDC 0.4 - 3/0.2 - 1.6/0 - 0.3A 75OFM40T-04 5/24/-12VDC 0.4 - 3/0.2 - 1/0 - 0.3A 75OFM40T-05 5/25/-5VDC 0.4 - 3/0.2 - 1/0 - 0.3A 75OFM40T-06 5/24/12VDC 0.4 - 3/0.2 - 1/0 - 0.3A 75OFM40T-07 3.3/5/-12VDC 0.4 - 5/0.2 - 2/0 - 0.3A682”W x 4”L x 1.2”H 40W to 60W Output Power Universal 90-264VAC Input Single Outputs from 3.3 to 48VDC High Efficiency to 88%3000V Isolation1U Compatible HeightModel Number Output Voltage Output Amps Efficiency %60 WATTOFM60-033 3.3VDC 8 74OFM60-050 5VDC 8 78OFM60-090 9VDC 6.67 82OFM60-120 12VDC 5 84OFM60-150 15VDC 4 85OFM60-240 24VDC 2.5 86OFM60-300 30VDC 2 86OFM60-360 36VDC 1.67 87OFM60-480 48VDC 1.2588INPUT SPECIFICATIONSInput Voltage Range 90-264 VACFrequency Range 47-63 HzInrush Current, typ: 30A @ 100VAC Input *50A @ 200VAC Input *OUTPUT SPECIFICATIONSVoltage and Current See Selection Chart Load Regulation (10-100% FL) Single Outputs +/-1%Dual/Triple Output +/-3%Line Regulation Singles +/- 0.5 max Preset Accuracy1%DC Voltage Adjust (typ) +/- 6% of FS (Primary) Temperature Coefficient +/-0.05%/°C Ripple/Noise, 20Mhz BW 50mV Pk-Pk, typ Over Voltage Protection Clamp, 130-150% *Short Circuit Protection Continuous, self-recovering Hold Up Time8 mS, typGENERAL SPECIFICATIONSInput-Out Isolation I/P-O/P:3000VAC Efficiency74%~88%, typSwitching Frequency 100Khz, (fixed, typical) SafetyUL, TUVPHYSICAL SPECIFICATIONSSize 2” x 4” x 1.2”50.8 x 101.6 x 30.48mm C onstructionOpen Frame Weight7oz (198g)ENVIRONMENTAL SPECIFICATIONSOper. Temperature 0 to +50°C(FL)Storage Temperature -40 to +85°C *Relative Humidity 0 to + 95%, non-cond * EMC CISPR/FCC Class B MTBF 300,000 HrsMil Std 217, 25C* These are stress ratings. Exposure of the devices to any of these conditionsmay adversely affect long term reliability. Proper operation under conditions other than the standard operating conditions is neither warranteed nor implied.All specifications are typical at nominal input, full load, and 25°C unless other-wise notedAstrodyne products are not authorized or warranteed for use as critical components in life support systems, equipment used in hazardous environments, nuclear controls systems, or other mission-critical applications.1009080706050403020100 10 20 30 40 50 60 70Ambient Temperature DegCLoad(%)OUTPUT DERATING CURVEMECHANICAL DIMENSIONSSingle Output Dual/Triple Output+v+v-V-VV2V1V1ComComV3Connector Mate TypeSingle Output Versions:Input: Molex 09-50-3031Output: Molex 09-50-3041Dual/Triple Output Versions:Input: Molex 09-50-3031Output: Molex 09-50-3061Note: Single/Dual Dimensional DifferencesDimensions Singles Dual/TriplesA 3.70 (94.00) 3.75 (95.3)B 1.70 (43.2) 1.75 (44.5)C 0.125 (3.17) 0.12 (3.0)。
Size Frequencyteristicdescription1Component loading上料Comp. location元件位置Component loaded onto correct slot元件上料到正确料位Component loading record上料记录100%ContinuesPD / IPQC check生产/IPQC对料Reload重新上料2Program selection程序选择Use corresponding program使用与该机种对应的程序BOM, DrawingBOM, 图纸100%Before produce开线前IE checkIE检查Change prog.更换程序3Orientation /Polarity / Location方向/极性/位置*Compliance with sample / drawing符合样板及实装图Compare with sample and drawing与样板及实装图比对1 pcs1 块Before produce开线前IPQC First articlerecord IPQC首件记录QM-0070-19Rebuild/recheck重打重检Multimeter 万用表4Componentcharacter元件特征*Resistance Refer to marking on part body.Capacitor value: Test电阻值参考本体标示读取。
对电容的容值进行量测。
Measure量测3pcsBefore produce开线前IPQC First articlerecord IPQC首件记录QM-0070-19Changematerial换料8Pre-oven insp.炉前检查-1Orientation /Polarity / Location方向/极性/位置Check if there are non-alignment, standing part,lacking part,short, excessive solder and so on检查料件是否有偏移，立碑，缺件，连锡，少锡，多锡等Visual check目检100%ContinuesIPQC patrolIPQC 巡检Repair andfeedback修理并反馈9Reflow回流焊FOLUNGWINreflow machine回流炉1Temperature profile炉温曲线Reflow parameter回流炉参数*Rising rate<3°C/sSoaking zone temperature: 150°C-180°CSoaking time:60s-120sReflow zone temperature>220°CReflow time: 30s-60sPeak temperature:236°C-250°CTemperature profile measurement炉温曲线测试1 time1次Change modelor per 24 hours换线或每24小时Daily reflow parameterrecord每日炉温参数记录Re-test重测曲线10Ceramicfunction Testing陶瓷板功能测试DC power supply直流电源1Lighting点亮*All LED can light, and no flash, no smell.Make sure LEDadhere C-PCB pad.陶瓷板上的LED正常发光，无闪灯，异味。
注意LED需紧贴陶瓷板焊盘。
Visual check目检100%Continuesdaily defect recordafter reflowing炉后检不良日报表SW-PD-FM-00021-01Repair修理11Side ceramicPCB loading侧面陶瓷板上料Loading machine上板机1Loading direction'上板方向Loading direction accord with printing machine setting. Andwearing glove during operation上板方向与印刷机设置的方向一致Visual check目视100%ContinuesIPQC patrolIPQC 巡检Adjust调整1Solder pastestorage锡膏存储Refrigeratortemperature电冰箱储存温度Storage temperature (0-10 ℃).存储温度：0-10 o CVisual check thereometer目检温度计显示100%ContinuesSolder paste storagetemperature record 锡膏储存温度记录表SW-PD-FM-00025-00Highlight tosuperior报告上司处理2Stirring solder paste锡膏搅拌Time of stirring锡膏搅拌时间Lay at room temperature for 4 hours.Stirring time: 5 minutes常温下放置4小时进行回温。
搅拌时间：5分钟Record process time记录过程时间100%ContinuesSolder paste usagecontrol record锡膏使用管制表Re-milling andconfirming重新搅拌并确认3Solder pastekeeping term锡膏保管期限Solder paste shelf life is six months.锡膏储存寿命为6个月Visual check目视100%ContinuesIPQC patrol recordIPQC巡检记录QM0070-20 -00Scrap过期作废4Solder pasteprinting锡膏印刷Solder pastethickness锡膏厚度Visual check if solder paste exceed printing area, if there issolder past sinking or solder needle目视检查锡膏是否超出印刷区域，是否有塌陷，拉尖Visual check目视1·~4 panelBefore produce开线前IPQC First articlerecord IPQC首件记录QM-0070-19Clean stencil oradjust pressure清洁钢网，调整压力等。
1Component loading上料Comp. location元件位置Component loaded onto correct slot, and make sure all LED（including top and side LED) has same CT range元件上料到正确料位,并且确保所有的LED（包括侧面和顶部）使用相同的色温范围。
Component loading record上料记录100%ContinuesPD / IPQC check生产/IPQC对料Reload重新上料NPM Mounting Machine贴片机FAI首件检查7Component placement 贴片12Solder Pasteprinting onceramic PCB陶瓷板锡膏印刷DEKSemi-auto printingMachine半自动锡膏印刷机placementNPM Mounting Machine贴片机No lighting灯不亮Gap between LED and PCBpad . LED 与焊盘有间隙Size Frequency teristicdescription 2Program selection 程序选择Use corresponding program 使用与该机种对应的程序BOM, Drawing BOM, 图纸100%Before produce开线前IE checkIE 检查Change prog.更换程序3Orientation /Polarity / Location 方向/极性/位置*Compliance with sample / drawing 符合样板及实装图Compare with sample and drawing 与样板及实装图比对 1 pcs 1 块Before produce 开线前IPQC First article record IPQC 首件记录QM-0070-19Rebuild/rechec k重打重检Multimeter 万用表4Component character 元件特征*Resistance Refer to marking on part body.Capacitor value: Test电阻值参考本体标示读取。
对电容的容值进行量测。
Measure 量测3pcsBefore produce 开线前IPQC First article record IPQC 首件记录QM-0070-19Change material 换料14Pre-oven insp.炉前检查-1Orientation /Polarity / Location 方向/极性/位置Check if there are non-alignment, standing part,lacking part,short, excessive solder and so on检查料件是否有偏移，立碑，缺件，连锡，少锡，多锡等Visual check 目检100%ContinuesIPQC patrol IPQC 巡检Repair and feedback 修理并反馈15Reflow 回流焊FOLUNGWIN reflow machine 回流炉1Temperature profile 炉温曲线Reflow parameter 回流炉参数*Rising rate<3°C/sSoaking zone temperature: 150°C-180°C Soaking time:60s-120sReflow zone temperature>220°C Reflow time: 30s-60s Peak temperature:236°C-250°CTemperature profile measurement炉温曲线测试 1 time 1次Change modelor per 24 hours换线或每24小时Daily reflow parameterrecord 每日炉温参数记录Re-test重测曲线16Ceramicfunction Testing陶瓷板功能测试DC power supply直流电源1Lighting 点亮*All LED can light, and no flash, no smell.Make sure LED adhere C-PCB pad.陶瓷板上的LED 正常发光，无闪灯，异味。
