FRF501G中文资料
- 格式：pdf
- 大小：125.47 KB
- 文档页数：2
Features
Low forward voltage drop High current capability High reliability High surge current capability
ITO-220AB
.1 34 (3 .4) D IA .11 3 ( 3 .0 )D I A
.112 (2 .85 ) .10 0 ( 2 .5 5)
1.0 Tj=25 0C
8.3ms Single Half Sine Wave JEDEC Method
0.1
0
20
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
FIG.6- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG
FRF 503G 200 140 200
FRF 504G 400 280 400 5.0 30 1.5 5.0 100
FRF 505G 600 420 600
FRF 506G 800 560 800
FRF Units 507G 1000 V 700 V 1000 V A A V uA uA nS ℃/W ℃
AVERAGE FORWARD CURRENT. (A)
5.0 4.0 3.0 2.0 1.0 0
FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG
1000
INSTANTANEOUS REVERSE CURRENT. ( A)
100
Tj=125 0C 10
0
8.0 4.0 2.0 1.0
FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG
300 250
INSTANTANEOUS FORWARD CURRENT. (A)
0.4 0.2 0.1
CAPACITANCE.(pF)
200 150 100 50 0 0.1 0.5 1.0 5 10 50 100 500 1000 REVERSE VOLTAGE. (V) Tj=25 0C f=1.0MHz Vsig=50mVp-p
50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr
NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms
-1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm
FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE
. 5 83 (1 4. 8)
. 11 0 (2 .8 ) .09 8 ( 2 . 5 )
. 5 43 (1 3. 8) . 5 12 (1 3. 2)
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
I(AV) IFSM VF IR Trr RθJA TJ, TSTG 150
250 4.0 -65 to +150
500
Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink.
Maximum Average Forward Rectified Current See Fig. 1 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @2.5A Maximum DC Reverse Current @ TC=25℃ at Rated DC Blocking Voltage @ TC=125℃ Maximum Reverse Recovery Time ( Note 1) Typical Thermal Resistance (Note 2) Operating and Storage Temperature Range
50 LEAD TEMPERATURE. ( C)
o
100
150
PEAK FORWARD SURGE CURRENT. (A)
FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG
30 25 20 15 10 5 0 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz
. 2 72 ( 6 .9 ) . 2 48 ( 6 .3 )
. 6 06 (1 5. 5)
Mechanical Data
Cases: ITO-220AB molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: Leads solderable per MIL-STD-202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260℃/10 seconds 0.25”,(6.35mion: Any Weight: 2.24 grams Mounting torque: 5 in – 1bs. max.
Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol FRF FRF Type Number 501G 502G Maximum Recurrent Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100
元器件交易网
FRF501G THRU FRF507G
Isolation 5.0 AMPS. Glass Passivated Fast Recovery Rectifiers
Voltage Range 50 to 1000 Volts Current 5.0 Amperes
- 448 -
元器件交易网
RATINGS AND CHARACTERISTIC CURVES (FRF501G THRU FRF507G)
FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
0.04 0.02 0.01 0.8 Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.9 1.0 1.1 1.2 1.3 1.4 1.5
INSTANTANEOUS FORWARD VOLTAGE. (V)
- 449 -
