锂离子电池用户手册 Lithium-ion Battery User's Guide

This Sheet is provided as technical information only. The information and recommendations set forth are made in good faith and believed to be accurate as of the date of preparation. SAMSUNG SDI Corp. makes no warranty, expressed or implied, with respect to this information and disclaims allMATERIAL SAFETY DATA SHEET3. H A Z A R D S I D E N T I F I C A T I O NPRIMARY ROUTES OF ENTRYSkin contact, Skin absorption, Eye contact, Inhalation, and Ingestion : NOSYMPTOMS OF EXPOSURESkin contact, Skin absorption, Eye contact, Inhalation→ No effect under routine handling and use.REPORTED AS CARCINOGENNOT APPLICABLE4.F I R S T A I D M E A S U R E SINHALATION, EYE CONTACT, and SKIN CONTACT: Not a health hazard.INGESTIONIf swallowed, obtain medical attention immediately.If exposure to internal materials within cell due to damaged outer casing, the following actions are recommended.INHALATIONLeave area immediately and seek medical attention.EYE CONTACTRinse eyes with water for 15 minutes and seek medical attention.SKIN CONTACTWash area thoroughly with soap and water and seek medical attention.INGESTIONDrink milk/water and induce vomiting; seek medical attention.5.F I R E F I G H T I N G M E A S U R E SGENERAL HAZARDCell is not flammable but internal organic material will burn if the cell is incinerated.Combustion products include, but are not limited to hydrogen fluoride, carbon monoxide and carbon dioxide.EXTINGUSHING MEDIAUse extinguishing media suitable for the materials that are burning.SPECIAL FIREFIGHTING INSTRUCTIONSIf possible, remove cell(s) from fire fighting area. If heated above 125°C, cell(s) can explode/vent.FIREFIGHTING EQUIPMENTUse NIOSH/MSHA approved full-face self-contained breathing apparatus (SCBA) with full protective gear.6.A C C I D E N T A L R E L E A S E M E A S U R E SON LANDThis Sheet is provided as technical information only. The information and recommendations set forthare made in good faith and believed to be accurate as of the date of preparation. SAMSUNG SDICorp. makes no warranty, expressed or implied, with respect to this information and disclaims allPlace material into suitable containers and call local fire/police department.IN WATERIf possible, remove from water and call local fire/police department.7.H A N D L I N G A N D S T O R A G EHANDLINGNo special protective clothing required for handling individual cells.STORAGEStore in a cool, dry place.8.E X P O S U R E C O N T R O L S/P E R S O N A L P R O T E C T I O N ENGINEERING CONTROLSKeep away from heat and open flame. Store in a cool dry place.PERSONAL PROTECTIONRespirator: Not required during normal operations. SCBA required in theevent of a fire.Eye/face protection: Not required beyond safety practices of employer.Gloves: Not required for handling of cells.Foot protection: Steel toed shoes recommended for large container handling. 9.P H Y S I C A L A N D C H E M I C A L P R O P E R T I E SState Solid Odor N/A PH N/A Vapor pressure N/AVapor density N/A Boiling point N/ASolubility in water Insoluble Specific gravity N/ADensity N/A10.S T A B I L I T Y A N D R E A C T I V I T YREACTIVITYNoneINCOMPATIBILITIESNone (during normal operation). Avoid exposure to heat, open flame, and corrosives.This Sheet is provided as technical information only. The information and recommendations set forth are made in good faith and believed to be accurate as of the date of preparation. SAMSUNG SDI Corp. makes no warranty, expressed or implied, with respect to this information and disclaims allThis Sheet is provided as technical information only. The information and recommendations set forth are made in good faith and believed to be accurate as of the date of preparation. SAMSUNG SDI Corp. makes no warranty, expressed or implied, with respect to this information and disclaims allHAZARDOUS DECOMPOSITION PRODUCTSNone (during normal operating conditions). If cells are opened, hydrogen fluoride and carbon monoxide may be released.CONDITIONS TO AVOIDAvoid exposure to heat and open flame . Do not puncture, crush or incinerate.11. T O X I C O L O G I C A L I N F O R M A T I O NThis product does not elicit toxicological properties during routine handling and use.Sensitization: NO Teratogenicity: NO Reproductive toxicity: NO Acute toxicity: NOThis product does not contain any kinds of the following substances and halogen-type flame retardants including Chlorine and Bromide type harmful flame retardants which are listed in Appendix of TCO documents and relevant international ECO requirements: Polybromated Biphenyls (PBB) Polybromated Biphenyl Ethers (PBBE) Polybromated Biphenyl Oxides (PBBO) Polybromated Diphenylethers (PBDE) Polychlorinated Biphenyl (PCB) Polychloronated Diphenylethers (PCDE) T etrabromphisphenol A (TBBPA) Asbestos, Antimonytrioxide, DioxineNone of the following substances will be exposed, leaked, or emitted during transportation, storage or any operation and any temperature condition:Chlorinated Fluorohydrocarbon (FCKW) Acrylonitride StyrolPhenol Benzol Mercury of greater than 0.0001 wt% for alkaline battery Mercury of greater than 0.0005 wt% for other battery Lithium content of greater than 0.5g/cell, 1.5g/battery Cadmium, lead, and other harmful heavy metalThis product does not contain mercury, cadmium and lithium-metal.Mercury content: N/A Lithium-metal: N/A Cadmium content: N/AIf the cells are opened through misuse or damage, discard immediately. Internal components of cell are irritants and sensitizers.15.T R A N S P O R T I N F O R M A T I O NThe rechargeable Lithium-Ion battery pack as stated in Appendix are made in compliance to the requirements stated in the latest edition of the IATA Dangerous Goods Regulations Packing Instruction 965 sectionⅡsuch that they can be transported as a NOT RESTRICTED (non-hazardous/non-dangerous) goods. However, if those lithium-ion battery packs are pack with or contained in an equipment, then it is the responsibility of the shipper to ensure that the consignment are packed in compliance to the latest edition of the IATA Dangerous Goods Regulations section Ⅱ of either Packing Instruction 966 or 967 in order for that consignment to be declared as NOT RESTRICTED (non-hazardous/non-Dangerous).With regard to transport, the following regulations are cited and considered:-The International Civil Aviation Organization (ICAO) Technical Instructions (2009-2010 Edition),-The International Air Transport Association (IATA) Dangerous Goods Regulations (51st Edition, 2010)-The International Maritime Dangerous Goods (IMDG) Code (2008 Edition),-US Harzardous Materials Regulations 49 CFR(Code of Federal Regulations) Sections 173-185 Lithium batterie and cells,-The UN Recommendations on the Transport of Dangerous Goods, Manual of Tests and Criteria 38.3 Lithium batteries, 4th revised edition(UN3480)Our products are properly classified, described, packaged, marked, and labeled, and are in proper condition for transportation according to all the applicable international and national governmental regulations, not limited to the above mentioned. We further certify that the This Sheet is provided as technical information only. The information and recommendations set forthare made in good faith and believed to be accurate as of the date of preparation. SAMSUNG SDICorp. makes no warranty, expressed or implied, with respect to this information and disclaims allThis Sheet is provided as technical information only. The information and recommendations set forth are made in good faith and believed to be accurate as of the date of preparation. SAMSUNG SDI Corp. makes no warranty, expressed or implied, with respect to this information and disclaims allenclosed products have been tested and fulfilled the requirements and conditions in accordance with UN Recommendations (T1 – T8) on the Transport of Dangerous Goods Model Regulations and the Manual of Testes and Criteria that can be treated as “Non-Dangerous Goods”.Test results of the UN Recommendation on the Transport of Dangerous GoodsManual of Test and Criteria (38.3 Lithium battery) Test Results RemarkNo Test item T1 Altitude Simulation Pass T2 Thermal Test Pass T3 Vibration Pass T4 Shock Pass T5 External Short Circuit Pass T6 Impact PassT7 Overcharge Pass For pack only T8 Forced Discharge Pass For cell only16. O T H E R I N F O R M A T I O NFor further information, please contact SAMSUNG SDI sales representative.。

User manual8.2KWH Lithium-ion batterySAFETY GUIDELINESWork or maintenance on the BSL battery should be carried out byqualified personnel only.Do not attempt to open or dismantle battery and/or cells.The electrolyte contained in the battery cells is highly corrosive.In the event of any damage to or leakage from the cells,treat contents with care, do not allow contact with exposed skin or eyes.DO NOT INGEST.The terminals of the BSL battery should always be considered live, therefore do not place tools or any other items across the terminals.Do not pierce,short or damage the terminals in any way.Do not touch theterminals of the battery.Fire Hazard:Do not discharge battery below specified minimum level as this poses an increased fire risk.Do not attempt to charge a swollen or damaged battery.In the event of fire,a CO2or Dry Powder extinguisher should be used.Class D extinguishers are not suitable.Dispose of batteries through the proper local regulations.Not suitable forregular refuse/recycling.Contents1Pin out diagram1 2Battery set-up22.1General (2)2.1.1Turning battery on and off (2)2.1.2CAN communication (2)2.1.3Smart shunt (2)2.1.4Dry contacts (2)2.1.5Other ports (2)2.2Multiple batteries (3)2.2.1Max number of parallel batteries (3)2.2.2Installing multiple batteries (3)2.2.3Cable sizing with multiple batteries (3)2.2.4Dip switch settings for multiple batteries (3)3Inverter set-up43.1Batteries per inverter size (4)3.2Battery set-up on Victron GX device (4)4Inverter settings(Victron)54.1General Tab (5)4.2Grid Tab (5)4.3Inverter Tab (6)4.4Charger Tab (6)4.5Assistant tab(a) (7)4.6Assistant tab(b) (7)4.7Assistant tab(c) (8)4.8Assistant tab(d) (8)4.9Assistant tab(e) (9)4.10Assistant tab(f) (9)4.11Assistant tab(g) (10)4.12Assistant tab(h) (10)5Other specifications11 List of Figures1Pin-out diagram for8.2kWh BSL battery (1)1Pin out diagramFigure1:Pin-out diagram for8.2kWh BSL battery.A-Power indicator lightB-Run light(battery activity)C-Alarm indicator lightD-State of charge indicator lightsE-Reset switch(BMS Power button)F-Dip switches for parallel connectionG-Dry Contacts(mostly unused)H-RS485Left port(Port1)I-CAN Port(Port2)J-RS232Port(Unused)K-RS485Right Ports(Ports4&5)L-Circuit breaker(terminal power)M-Positive terminalN-Negative terminalO-Carry handlesP-Mounting holes2Battery set-up2.1General2.1.1Turning battery on and offThe battery can be switched on or off by holding down the small recessed button marked “RESET”.2.1.2CAN communicationA VE.Can to CAN-bus BMS“Type B”cable is required for CAN-Bus communication between the BSL battery and the Victron GX device.Some inverters will use differ-ent cable configuration,please check this with inverter suppliers.(Black to inverter/GX device,red to battery).2.1.3Smart shuntA Battery Monitoring Device(Victron BMV/Smartshunt)is not required as State of Charge(SOC)is sent to the GX device via the CAN-Bus cable.2.1.4Dry contactsDry Contacts are mostly unused,but for communication with some non-smart systems please see the table below.Working current should be less than2A,mainly to connect with an external indicator light or buzzer.2.1.5Other portsPort1(RS485)and port3(RS232)are used for programming and retrieving information only and must be left open.2.2Multiple batteries2.2.1Max number of parallel batteriesA maximum of20batteries can be connected in parallel.Each battery will require a unique binary address which can be setup via the dip-switches located on the front of the battery.2.2.2Installing multiple batteriesWhen installing more than one battery in parallel,a standard RJ45patch network cable will be required for inter-battery communication.These cables will need to be connected to port4or5between all the connected batteries.The ports are paralleled therefore any port can be used for in or out connection.2.2.3Cable sizing with multiple batteriesIt is recommended to make use of a common rail bus-bar when more than4batteries are to be installed.All positive cables running between the battery and bus-bar must be the same length and all negative cables must be the same length.The batteries should be evenly grouped where possible.The recommended battery cable sizes from the batteries(going to the inverter)in par-allel are as follows:1battery-50mm2,2batteries-70mm2,3batteries-95mm2or 2×50mm2,4batteries-120mm2or2×70mm22.2.4Dip switch settings for multiple batteries3Inverter set-up3.1Batteries per inverter sizeInverter size Recommended N.O.batteries Minimum N.O.of batteries 15kVA3210kVA228kVA215kVA113kVA113.2Battery set-up on Victron GX device1.The VE.Can to CAN-bus BMS Type B cable needs to be connected to the VE-Canport on the GX device and the second unused VE.Can port needs to be terminated with the Victron blue terminator.Ensure that the cable is marked CCGX at the end.2.Press the enter button on the GX device.This should take you to the device listpage.Scroll down to settings,press enter,and scroll to services and press enter again.Navigate to the CAN settings and change the CAN speed from250KB to 500KB.3.Scroll to DVCC and select Switch DVCC on.Flag SHARED VOLTAGE SENSEand CHARGE LIMIT.Set CCL(charge current limit)to80amps/battery.4.Navigate back to the device list and the BSL battery should appear on the devicelist.5.Select the BSL battery set the parameters as follows:•Charge Voltage54.5V.•Charge Current Limit:90A per battery(recommended80A).•Discharge Current Limit:180A per battery(constant150A).4Inverter settings(Victron) 4.1General Tab4.2Grid Tab4.3Inverter Tab4.4Charger Tab4.5Assistant tab(a)4.6Assistant tab(b)4.8Assistant tab(d)4.10Assistant tab(f)4.12Assistant tab(h)5Other specifications。

锂电池使用说明书一、引言锂电池是一种常见的电池类型，广泛用于移动设备、电动车辆和储能系统等领域。

本使用说明书将详细介绍锂电池的正确使用方法、注意事项和安全操作规范，以确保用户正常、安全地使用锂电池，并最大程度地延长其使用寿命。

二、锂电池概述1. 类型：锂电池主要分为锂离子电池（Li-ion）和聚合物锂离子电池（Li-polymer）两种常见类型。

前者具有高能量密度和较长的使用寿命，后者则具有更小的尺寸和更高的安全性能。

2. 电压：锂电池的标准电压一般为3.7伏（V），但实际使用中，电压可能会在充放电过程中有所波动。

3. 容量：锂电池的容量一般以毫安时（mAh）为单位。

容量越大，电池存储的电能越多，使用时间也相应延长。

三、使用方法1. 充电：使用专用的锂电池充电器进行充电，确保使用正确的充电电压和电流。

避免使用不兼容、低质量的充电器，以免引发充电事故。

2. 放电：在使用锂电池时，请避免将电池放空至完全放电状态，以免损害电池性能。

适当提前进行充电，避免电池电量过低而无法正常工作。

3. 储存：长时间不使用锂电池时，请将电池储存在干燥、阴凉的环境中，并保持电池电量处于50%左右的状态。

避免高温环境和过度放电，以防止锂电池损坏。

四、注意事项1. 温度：锂电池对温度非常敏感。

请避免将锂电池暴露在极端的高温或低温环境中，以免影响电池性能和安全性能。

2. 碰撞：请避免对锂电池进行剧烈碰撞或挤压，以免导致电池损坏、电池液泄漏或短路，并可能引发火灾或爆炸等危险。

3. 液体接触：请避免将锂电池浸入液体中，如水或其他溶液，以防止电池短路、电池液泄漏或发生火灾等意外情况。

Congratulations on your purchase of this product. Please read this user manual carefully.This charger is designed for Li-ion packs solely.When charging two packs, the charger will simultaneously at 1.5A per hour charge rate. 98Wh packs will charge in approximately 4 hours.Rugged, sleekly styled, compact charger chassis.Automatic Universal AC input for world-wide use.Automatic detection of damaged or misued batteries for added safety.Insert the AC power cord into the AC receptacle in the back of the charger.Connect all batteries needing charge into the charger.Turn the rear panel power switch to the ON position. At this time the switch will light and the LED lights on the front panel of the charger will blink green when charging.If the battery does not meet quick charging conditions (i.e.temperature or deeply discharged) the charger ill precharge the battery and go into a trickle charge mode until it is safe to enter quick charge mode.The LED corresponding with the charging bay will turn solid green when the battery is fully charged.Warranty:This product is warranted to the Original Purchaser against all defects in material and or workmanship for the period herein.The warranty period shall be 3 years for parts and labor, unless otherwise noted.Input 100~240VA, 50/60Hz Charging Output 3A (Max) x 1, 1.5A x 2Adapting Output DC 15V, 6A (max)Working T emperature 0°C~+45°CDimension 4.5” x 5.5” x 3”Weight Approx. 1.0 lbs FeaturesChargingSpecifications。

User Manual Rechargeable Lithium Ion Battery SystemLynx Home U SeriesV 1.3-2022-08-30User Manual V1.3-2022-08-30DisclaimerDisclaimer• All the information in this document is the property of the manufacturer. No part of this document could be reproduced in any way for business use. Internal use is allowed.• The manufacturer makes no representations or warranties express or implied, with respect to this document or any of the equipment and/or software it may describe, including(with no limitation) any implied warranties of utility, merchantability, or fitness for any particular purpose.All such representations or warranties are expressly disclaimed. Neither the manufacturer nor its distributors or dealers shall be liable for any indirect, incidental, or consequential damages under any circumstances.• The exclusion of implied warranties may not apply in all cases under some statutes, and thus the above exclusion may not apply.• Specifications are subject to change without notice. Every effort has been made to make this document complete, accurate, and up-to-date. However, the manufacturer may need to make some improvements under certain circumstances without advance notice. The manufacturer shall not be responsible for any loss caused by this document including, but not limited to omission errors, typographical errors, arithmetical errors, or listing errors in this documents.Limitation of LiabilityThe manufacturer shall not be liable for any consequences like battery damage or property loss under the following circumstances:• Modify, alter, or replace parts of the battery system without official authorization from the manufacturer.• Anyone except technicians from the manufacturer changes or erases the serial number.• Establish a battery system that does not meet the criteria, safety regulations, and otherrelated requirements.• Non-observance to the User Manual.• Improper use or misuse of the battery.• Inadequate ventilation.• The maintenance routine does not follow accepted standards.• Force majeure like earthquakes, storms, thunders, over voltage, or fire hazards, etc.• Any external factors.UpdatesThe latest document contains all the updates made in earlier issues.V1.0 2021-03-30• First release.V1.1 2021-07-19• Updated 5.3System Installation.V1.2 2022-03-15• Updated 2.2 Symbol Description.V1.3 2022-08-30• Updated 5.3.3 Cable Connection.• Updated 6.2 Power On.• Updated 6.5 Power Off.• Updated 07 Technical Parameters.User Manual V1.3-2022-08-30Content TABLE OF CONTENTS 01 Safety Precaution .......................................................................0102 Product Introduction .. (03)2.1 Product Description (03)2.2 Symbol Description (03)03 Battery Introduction (04)3.1 Appearance (04)3.2 Dimensions (04)04 Storage and Package (05)4.1 Storage Environment (05)4.2 Packing List (05)05 System Installation (06)5.1 Installation Environment (06)5.2 Space Requirements (06)5.3 System Installation (08)5.3.1 Floor Mounting (08)5.3.2 Wall Mounting (09)5.3.3 Cable Connection (10)5.3.4 Install the Wire Harness Fix Bar (13)06 System Operation (14)6.1 Check Before Power On (14)6.2 Power On (14)6.3 Battery Parameter Settings (16)6.4 Indicator Status(LX U5.4-L) (16)6.4.1 Normal State (17)6.4.2 Alerting (17)6.4.3 Faulty (18)6.5 Indicator Status(LX U5.4-20) (19)6.5.1 Normal State (19)6.5.2 Alerting (19)6.5.3 Faulty (20)6.6 Power Off (21)6.7 Install the Plastic Cover (21)07 Technical Parameters (22)08 Maintenance (24)Remove the Plastic Cover (24)User Manual V1.3-2022-08-3001 Safety Precaution 01 Safety Precaution01 Safety Precaution User Manual V1.3-2022-08-30The Battery sold in the European market meets the following directives and requirements:• Electromagnetic compatibility Directive 2014/30/EU (EMC)• Electrical Apparatus Low Voltage Directive 2014/35/EU (LVD)• Restrictions of Hazardous Substances Directive 2011/65/EU and (EU) 2015/863 (RoHS)• Waste Electrical and Electronic Equipment 2012/19/EU• Registration, Evaluation, Authorization and Restriction of Chemicals (EC) No 1907/2006 (REACH)You can download the EU Declaration of Conformity on https://.02 Product Introduction User Manual V1.3-2022-08-302.1 Product Description2.2 Symbol Description02 Product Introduction Goodwe Inverter• This manual introduces Lynx Home U Series(LV) Battery System (hereinafter referred to as the Battery System), including the product introduction, application, installation, commission, and technical parameters, etc.• At most 6 batteries can be connected in this Battery System.• The battery system can be compatible with the following inverter series:03 Battery Introduction User Manual V1.3-2022-08-30 03 Battery Introduction3.1 Appearance3.2 Dimensions04 Storage and PackageUser Manual V1.3-2022-08-304.2 Packing List• Check outer packing for damage and model before unpacking it. If you find any damage or the model is not what you requested, do not unpack the product and contact the after-sales service as soon as possible. • Check whether the deliverables are intact and complete first after unpacking the battery.If anything wrong, contact the after-sales service as soon as possible.4.1 Storage Environment04 Storage and PackageIf the equipment is not to be installed or used immediately, please ensure that the storage environment meets the following requirements:• Pack the equipment using a packing box and put some desiccant in the box before sealing.• Put the equipment back to the packing box if it is not to be installed in 3 days after unpacking.• Storage SOC: 25%~50%SOC. Charge and discharge the battery every 3 months.• Recommended storage temperature: -20℃~40℃(less than one month) or 0℃~35℃(less than one year). • Recommended storage humidity: 0%~95%RH(no condensation). Do not install the battery if any moist or condensation is found.• Place the quipment in a cool place where away from direct sunlight.• Keep the equipment away from inflammable, explosive, and corrosive matters.•Keep the equipment away from the rain.05 System Installation User Manual V1.3-2022-08-305.1 Installation Environment5.2 Space Requirements05 System Installation• Install the Battery System on the ground with sufficient bearing capacity and flatness. Increase the bearing capacity and flatness of the ground by laying the foundation, adding bearing plates and so on. • The optimal temperature for the battery is 20~40℃.• Avoid exposing the equipment to direct sunlight or rain.• Install the equipment away from heat/cold source.• Do not install the equipment in the place where the temperature changes extremely.• Install the equipment away from strong interferences to ensure its regular work.• Keep children away from the equipment.• Do not install the equipment in places prone to accumulate water.•Do not put inflammable or explosive matters near the equipment.Keep the equipment away from children.05 System InstallationUser Manual V1.3-2022-08-30Installation Angle Requirements• Install the equipment vertically, no tilt or upside down.Mounting Support Requirements• The mounting support shall be nonflammable and fireproof.• Install the equipment on a surface that is solid enough to bear the product weight.• Put the battery system near the wall and install the locking brackets to prevent the battery from falling down5.3.1 Floor MountingStep1 Screw the anti-dumping bracke on the battery.Step2 Align the battery and the wall, then put the anti-dumping bracket close to the wall. Mark the drilling position and remove the battery.Step3 Drill a hole on the wall using the driller. Hole diameter 10mm and depth 80mm.Step4 Fix the expansion bolts, tightening torque: 10N·m.5.3.2 Wall MountingStep1 Place the wall mounting plate close to the wall firmly, mark the drilling position and remove the wall mounting plate.Step2 Drill a hole on the wall using the driller. Hole diameter 13mm and depth 65mm.Step3 Fix the M10 expansion bolts, tightening torque: 10N·m.Step4Install the battery on the mounting plate.5.3.3 Cable ConnectionOverview of the cable connectionStep1 Prepare PE cable.Step2 Crimp the PE cable.Step3 Install the Heat shrink tube.Step1 Prepare Power cable.Step2 Disassemble the Power connector.Step3 Insert the Power Cable into the Power connector.Step4 Plug the Power connector into the Power Cable Port.RJ45 Registered JackCAN COM Port Step1 Remove the waterproof module.06 System Operation6.1 Check Before Power OnStep1 (Optional) Turn on the breaker between the inverter and the battery system.Step2 (Optional) Turn on the breaker between the batteries (For parallized batteries).Step3 Turn on the inverter in the system following the instructions in the user manual of the inverter.Step4 Turn on the Circuit-Breaker.Step5 Press the switch button of all batteries in 30s, otherwise the equipment will start alarming.Step1 (Optional) Turn on the breaker between the inverter and the battery system.Step2 (Optional) Turn on the breaker between the batteries (For parallized batteries).Step3 Turn on the Circuit-Breaker.Step4 Press the battery buttons. (Only press one battery's button when batteries are in parallized connection.)Step5 Turn on the inverter in the system following the instructions in the user manual of the inverter.LX U5.4-LLX U5.4-20Select the right options on PV Master after connecting the battery and the inverter.Select “LX U5.4-L or LX U5.4-20” on PV Master.Select the battery model on PV Master:6.3 Battery Parameter Settings"Battery Selection Abnormal" will be displayed if you select 6.4 Indicator Status(LX U5.4-L)SOC IndicatorButton Indicator06 System Operation User Manual V1.3-2022-08-3006 System OperationUser Manual V1.3-2022-08-30SOC IndicatorButton Indicator6.5 Indicator Status(LX U5.4-20)06 System Operation User Manual V1.3-2022-08-30 6.5.3 Faulty06 System OperationUser Manual V1.3-2022-08-30Please follow the steps to power off the Battery System, otherwise, the System may be damaged.6.6 Power OffStep1 Disconnect the circuit breakers of all batteries.Step2 Make sure that the SOC indicator of the battery is off.Step1 Press the switch button for at least 5s until the indicator lights off. Press the button of any one battey if multi batteries are connected.Step2 Turn off the Circuit-Breaker.Step3Make sure that the SOC indicator of the battery is off.LX U5.4-LLX U5.4-2007 Technical Parameters User Manual V1.3-2022-08-30 07 Technical Parameters07 Technical ParametersUser Manual V1.3-2022-08-3008 MaintenanceUser Manual V1.3-2022-08-30GoodWe Technologies Co., Ltd.No. 90 Zijin Rd., New District, Suzhou, 215011, China******************Local Contacts。

USER GUIDE4The Anton/Bauer Titon Series Lithium-ion batteryis specifically designed and optimized to becharged with current Anton/Bauer chargers. TheTiton battery Series are compatible with Anton/Bauer chargers and have been tested on industryrecognized competitive chargers as well. Foroptimal performance and enhanced batterylongevity, we recommend using Anton/Bauerchargers.5Weekly, or as needed - Clean the device, associated components, and accessories as needed with a damp, non-saturated cloth or paper towel. Do not wet the exposed metal part of the battery charge terminals. Do not use solvents or scouring agents. Examples of approved solvents are Cidex® and Windex®. Consult Anton/Bauer Customer Support Group for approved list of cleaning agents.Periodic cleaning of both the charger terminals and battery terminals will ensure continued reliable operation. Clean the terminals occasionally with a pencil eraser or lightly scrape the surface with a blunt instrument to help reduce the likely hood of build up causing poor communication or charging.Contact Anton/Bauer Customer Support Group with additional inquires as to maintenance.CAUTION! Keep batteries cool or at room temperatures whenever possible. Sustained elevated temperatures are the primary reason for premature failure of Lithium-Ion batteries.CAUTION! Charge batteries at room temperature. In warm climates keep chargers in air conditioned rooms for best performance.CAUTION! Although Lithium-ion has good selfdischarge characteristics, batteries should be stored for long term storage in a fully charged condition.CAUTION! Batteries should always be stored in a fully charged state and kept cool. If batteries must be stored for a long period (over 30 days), the battery electronics will enter a “deep sleep” mode. The battery will “wake up” when placed on a charger. It is always a good idea to submit the battery to a discharge/charge cycle from time to timeduring storage.Air Transportation Regulation1. US Code of Federal Regulations Title 49 Subtitle B.2. International Air Transport Associations (IATA) Dangerous Goods Regulation (DGR).3. International Civil Aviation Organization (ICAO) regulations apply to all Lithium-Ion battery transport.Since the interpretation and application ofregulations may vary with the aviation company, the transport of the Anton/Bauer Titon Seriesbattery may be disallowed even when the conditions described above are satisfied. Anton/Bauer therefore strongly recommends that you consult with your transportation company prior to transporting the battery pack.678 Every Titon Series battery has an easy to read LCD which conveniently reports battery information in one of two ways.Titon Series LCD2. When the battery is sitting idle (no load is applied) the LCD willshow remaining capacity as percentage of full.When the battery is powering an item (a load is applied), the LCD will display remaining run-time in Hours/Minutes.1.9The Titon Series features an Integrated PowerTap® and USB ports on the side of the battery to power camera accessories.The PowerTap® allows for convenient deployment of up to 10 Amps of DC current for various parallel devices. The USB port supplies a regulated 5 volts and maximum 2 Amps current and may be used for charging mobile devices.10Will deliver a high rate charge matched to thecapabilities of the battery (typically a one or twohour rate, depending on battery type). Duringthis stage, six separate cutoff methods are inoperation, simultaneously, ensuring the fastest,safest charge for that battery.Charging is a BALANCING or “stabilizing” modewhich calculates each battery pack type to offsetany imbalance of the battery’s cells, created byunequal self-discharge or any capacity mismatchof the individual cells in the pack. This stage canvary in duration from zero to as much as 16 hours,depending on the condition of the battery. TheStage Two charge reduces current automaticallyas the battery charges maintaining the cells at asafe voltage level. A battery will typically leaveStage Two in 2-4 hours under average operatingconditions.Charging is the Anton/Bauer exclusive Lifesaver®maintenance mode. This patented pulse routinekeeps batteries fully charged, free from self-discharge - indefinitely - without damaging heatassociated with a so-called “trickle charge”. TheStage Three programming monitors the self-discharge of the battery, providing charge onlywhen the battery self-discharges to about 95% ofits capacity.Mount any Titon Series battery to any open position on an Anton/Bauer charger andthe charger will automatically determine the appropriate charge routine and execute it.In some cases a battery may be discharged to a very low voltage levelcausing the battery to be unrecognizable to the charger when first attached.T i to n 150 Wh: Max. Discharge Rate 168W or 10AOutput Voltage Nominal 14.4V Operating 10.0~16.8VThis equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense. This equipment has been approved by one or more agencies. All changes and/or modifications not expressly approved by Anton/Bauer could void the users’ warranty and authority to operate this equipment. There are no serviceable parts in this equipment.14This warranty for the product specified in this document (“Product”)is given by Vitec Production Solutions (“Anton/Bauer”), 14 Progress Drive, Shelton, Connecticut 06484. If you (the purchaser of the Product from Anton/Bauer, or the person for whom the Product was purchased, if it was a gift) have any questions regarding Product applications, Product specification, or to obtain warranty service on this or any Anton/Bauer product, contact the company at the address above.THIS PRODUCT MUST BE REGISTERED WITH ANTON/BAUER WITHIN 30 DAYS OF PURCHASE TO ASSURE WARRANTY COVERAGE. REGISTER ONLINE AT:Warranty registration, including the serial numbers of Anton/Bauer chargers used with this battery, must be supplied to Anton/Bauer. Anton/Bauer will warranty the Product only against defects in material and workmanship for the period as follows from the date of purchase, in accordance with the terms set forth below, and then, only if the Product is used exclusively in conjunction with compatible Anton/Bauer chargers. If this battery or product is returned to Anton/Bauer for warranty service it will be required that you provide model names and serial numbers of compatible Anton/Bauer chargers with which this product was used.MAXX II Warranty 24 months: Anton/Bauer will repair or replace the Product at Anton/Bauer’s option and cost.This warranty shall be effective only if Anton/Bauer receives notice of such defects in materials or workmanship during the period of the warranty. The liability of Anton/Bauer hereunder is expressly limited to a claim for repair or replacement of the Product or as otherwise stated herein at Anton/Bauer’s sole discretion. Notice of any claim under this warranty shall be delivered to Anton/Bauer during the period of the warranty and the Product shall be returned with its packaging promptly, at your expense, to an Anton/Bauer Customer Support Center or to the address above. Upon receipt of the Product and a record of your compliance with the conditions of this warranty, Anton/Bauer will repair or replace the Product and return it to you, or issue a credit, as applicable. You are responsible for all shipping and handling charges to and from authorized facility.THIS WARRANTY DOES NOT APPLY TO AND IS VOID IN THE CASE OF DEFECTS OR DAMAGE RESULTING FROM ACCIDENTS, DISASTER, NEGLECT, MISUSE, IMPROPER INSTALLATION, IMPROPER OR UNAUTHORIZED SERVICE OR MAINTENANCE, UNAUTHORIZED REPLACEMENT PARTS OR ATTACHMENTS; OR DYSFUNCTION OR MALFUNCTION OF, OR CAUSED BY, ANY OTHER PRODUCT OR DEVICE.Misuse includes any use of the Product in other than its intended application, including the use of this Product with any charging device or accessory not manufactured by and/or specified by Anton/ Bauer. This warranty does not cover, and Anton/Bauer assumes no responsibility for, any equipment or devices used in conjunction with the Product.ANTON/BAUER DISCLAIMS ANY LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY OF THE PRODUCT. UNDER NO CIRCUMSTANCES WILL ANTON/BAUER BE RESPONSIBLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIALDAMAGES.This Warranty is to be construed and enforced in accordance with the law of the State of Connecticut, including the provisions of the Uniform Commercial Code as adopted and from time to time amended in the State of Connecticut, and not the Convention for the International Sale of Goods. This choice of Connecticut law is exclusive of any Connecticut law that would require reliance on any law foreign to Connecticut.15Part No. 7595-0465。

January 2020 Printed or other static representations of this document are considered uncontrolled and Page 1 of 5for reference-only.FedEx Express does not provide these DG Labels. Customers may order these labels from vendors, such as those at /labels.Figure 1Figure 2Figure 3***Lithium Battery Class 9 Hazard Label Lithium Battery MarkCargo Aircraft Only Labe lNOTE : No text other than the Class “9” must be included in the bottom part of the Lithium Battery Class 9 label. IATA 7.2.2.4***Shipper must add UN number(s). It should be 12 mm high AND Shipper must complete phone number portion of label.AGGREGATE LITHIUM CONTENT - The sum of the grams of lithium content contained by the cells comprising a battery. [IATA Appendix A]In addition, check: /us/services/pdf/LithiumBatteries_Limitations.pdf2 1January 2020 Printed or other static representations of this document are considered uncontrolled and Page 2 of 5for reference-only.LITHIUM METAL BATTERIESLithium Metal Batteries packed with equipmentUN3091, P.I. 969Lithium Metal Batteries contained in equipmentUN3091, P.I. 970AGGREGATE LITHIUM CONTENT - The sum of the grams of lithium content contained by the cells comprising a battery. [IATA Appendix A]2LITHIUM ION BATTERIESJanuary 2020 Printed or other static representations of this document are considered uncontrolled and Page 3 of 5for reference-only.In addition, check: /us/services/pdf/LithiumBatteries_Limitations.pdf1LITHIUM ION BATTERIESJanuary 2020 Printed or other static representations of this document are considered uncontrolled and Page 4 of 5for reference-only.January 2020Printed or other static representations of this document are considered uncontrolled andPage 5 of 5for reference-only.Note:•FedEx Express will not accept any item with an A183 Special Provision, even with a Competent Authority approval. Any battery powered device subject to a recall will only be accepted if the recall is not safety related and the battery does not have the potential to cause a fire or dangerous evolution of heat. [FX-04E]•Lithium Batteries (Section I/IA/IB and Section II) must not be shipped in the same package with the following Hazard Classes/Divisions:1.4,2.1, 3, 4.1, 4.2, 4.3, 5.1, 5.2, 8, or 2.2 with a Cargo Aircraft Only label. This includes All Packed in One and Overpacks.Exception: If the only lithium batteries are those contained in temperature control devices and the lithium batteries are Section II. The package must also not require the Lithium Battery Mark and ELB (FedEx Express DG handling code for Section II batteries) must not be selected in the automation device. [FX-05C]•Shippers sending any data loggers which remain active in flight (other than FedEx SenseAware) must be pre-approved. Contact theFedExDangerousGoods/HazardousMaterialshotlineat(901)375-6806oremail:*************************************process. [FX-05D]•Hoverboards or similar self-balancing vehicles will only be accepted from companies if new, in unopened original packaging. Used,refurbished balancing vehicles shipments form individuals, resellers or third party shipments will not be accepted. [FX-04F]•Call FedEx customer service and ask for the International Hotline/ Specialist to check on commodity acceptability for international shipments1In addition, check: /us/services/pdf/LithiumBatteries_Limitations.pdf•Select ELB in your FedEx automation device, if selection is available for any Section II UN3091 or UN3481 required to be labeledwith the Lithium Battery Mark.Class 9 Miscellaneous DangerousGoods Hazard Label Lithium Battery LabelObsolete effective 01/01/19The Class 9 label cannot be used as the hazard label for Section I/IA/IB shipments effective 01/01/19.The Lithium Battery Class 9 hazard label must be used instead.If you have questions please contact the Dangerous Goods/Hazardous Materials Hotline at (800) GOFEDEX and press “81” or say dangerous goods. Press “4” to reach next available agent.DISCLAIMER:This guide is based upon the 2020 IATA Dangerous Goods Regulations and provides a general overview of lithium battery shipping requirements. It does not provide complete shipping information. Consult the packing instruction and all applicable Special Provisions for the product being shipped.These materials are provided as a courtesy, to be used as guidelines to assist properly trained shippers. These materials do not alter, satisfy, or influence anygovernmental requirements. The contents of these materials are subject to change due to constant changes in government regulations. FedEx Express accepts noliability for loss or damage resulting from changes, errors, omissions, or misinterpretations of these materials.。

Contents 目录1Preface 前言2Definition 定义Nominal capacity 标称容量Standard charge method 标准充电方式Standard discharge method 标准放电方式3Cell type and dimension电芯型号及尺寸Description and model 电芯说明及型号Cell dimension 电芯尺寸4Cell characteristics电芯特性5Technical requirements技术要求Cell usage conditions 电芯使用环境Cell testing conditions 电芯实验环境Requirement of the testing equipment 测量仪表要求Electrochemical characteristics 电化学特性Environmental characteristics and safety characteristics 环境适应性能与安全性能6Package picture 包装图片7Shipment 出货8Warranty 质量保证9Storage and Shipment Requirement 存储及运输要求10Warning and cautions in handling the lithium-ion cell 电芯使用时警告事项及注意事项11The restriction of the use of hazardous substances 有害物质控制要求12Contact information 联系方式13Version history 修订履历1preface 前言2This specification describes the type and dimension, performance, technical characteristics, warning and caution of the lithium ion rechargeable cell. The specification only applies to N18650CL-29 cell supplied by Zhengzhou BAK Battery Co., Ltd.本标准描述了圆柱型锂离子电芯的外型尺寸、特性、技术要求及注意事项。

History of specification规格书修订记录Date Contents Remarks 2018-05-12First issue A0Content/目录1.Scope/适用范围Page42.Cell Specification/电芯规格说明Page4/53.Battery/Cell performance test Criteria/电池性能标准Page6 3.1Appearance inspection by visual/外观目测Page6 3.2Environmental test condition/外界环境条件Page6 3.3Electrical characteristics/电气特性Page6 3.4Mechanical characteristics/机械特性Page73.5Safety performance/安全性能Page7/84.Cell initial Dimensions/电芯初始尺寸Page84.2Picture of assembled battery组合电池图5.Protection Circuit保护电路5.1PCM parameter PCM参数6.Circuit topology Drawing and PIN Explanation电路布线图和焊盘说明6.1PCM BOM保护板物料清单6.2Assembled cell parameters包装后电芯组参数附录Page9 Page9 Page9 Page10 Page10 Page101.Scope/适用范围2.Cell Specification/电芯产品规格No.Item项目Specification性能1Rated Capacity额定容量3000mAh,0.2C discharging2Minimum Capacity最小容量3000mAh,0.2C discharging3Normal Voltage标称电压3.70V4O.C.V出厂电压 3.80-4.2V5Charge Ending Voltage充电截止电压4.20±0.03V6Discharge Ending Voltage放电截止电压3.0V7Standard charging method标准充电方式0.5C constant current charge to 4.2V,then constantvoltage4.2V charge till charged current declines to≤0.01C,0℃～45℃8Charge current充电电流Standard charge:0.5CRapid charge:1.0C9charging Time充电时间Standard charge:5.5～6.5hRapid charge:1.5～2.5h10Max.Charging Current最大充电电流1.0C(5℃～+45℃)11Standard dischargingCurrent标准放电电流0.5C constant current discharge to3.0V.10℃～+60℃12Max.Discharging Current最大放电电流1.0C(10℃～+60℃)13Operating environment工作环境Charging:0℃-45℃,65%±25%RHDischarging:10℃-60℃,65%±25%RH14Cell Impedance单电芯内阻＜45mohm，(4.2V AC1KHz measured)15Dimension of Single Cell单电芯尺寸Thickness Max8.0mmWidth Max56.5mmHeight Max60.5mm3.Picture of single cell单体电芯图Items Description Dimension and SpecT电芯厚度Max:8.0mmW电芯宽度Max:56.5mmH电芯长度Max:60.5mmC Tab间距18±2.0mmB Tab宽度 4.0±0.1mmD顶封宽度 4.0±0.5mmA极耳胶外露Max:2.0mmE极耳长度8.0±1.5mmFig.(1)The Dimension of Single Cell图(1)单体电池尺寸图4.Picture of assembled battery组合电池图Fig.(2)The Dimension of Assembled Battery图(2)组合电池外形尺寸图厚度T 宽度W 长度L 线径Ø线型插头型号Max:8.1Max:57.0Max:63.00.9UL1007/24#XH2.54-2P备注：UNIT 单位：MM5.产品规格及电气参数Product Specification and Electrical Parameters序号Item项目Specification性能1Assembled Mode组合方式1P2Normal Capacity标称容量≥3000mAh,0.2C discharging3Normal Voltage标称电压3.7V4Impedance成品内阻＜103mohm，(100%charge AC1KHz measured)5Assembly Dimension装配尺寸Thickness Max8.1mmWidth Max57.0mmHeight Max63.0mm4.Battery/Cell performance test Criteria/电池性能标准4.1Appearance inspection by visual/外观目测There shall be no such defect as rust,leakage,which may adversely affect commercial value of battery.电池外观应没有锈渍、污渍、漏液等影响商业价值的缺陷存在。

V200 rechargeable li-ion BatteryUSER MANUALWE STRONGLY RECOMMEND THAT YOUREAD THIS INSTRUCTION BEFORE USINGYOUR BEBOB V200 BATTERY! PLEASEKEEP THIS MANUAL FOR FUTUREREFERENCEFeatures• A high capacity battery which is compact and lightweight. Direct fitting to a camera via V-Mount.•Five-step LED power indicator (100% - 80% - 60% - 40% - 20%).•From SN V20000810, full Capacity Status LED (green over 70%; yellow between 50% and 70%; red under 50%)Safety instructions•Only for professional use! Keep batteries out of reach of children and personnel that has not been instructed in the use of high capacity Lithium-ion batteries!•Use only with recommended charger.•Keep the battery dry and do not immerse in water.•Never open the case of the battery.•Do not expose to temperature over 60°C.•Do not expose the battery to fire! May explode if thrown into fire!•Maximum Load 16.0A.•Do not put the battery on a device when the red charging LED flashes.•Handle with care! Do not throw! Do not drop!Charging•Never leave batteries unattended while charging•Wait 30 Minutes after discharge before you put the battery on a charger.•The bebob V200 battery can be charged with an external bebob charger (or equivalent) with Lithium-ion (Li-ion) charging ability.•Approximate charge time may vary depending on charger and temperature.•bebob V200 can be charged in ambient temperature for optimum performance at 10°C - 30°C.•bebob V200 batteries can be recharged in any charge condition.Discharging•Maximum load is 16.0A. When using the battery with video or lighting equipment, power consumption of the equipment must be 16.0A or below. For the protection of the battery, aload of 16.0A or over may activate the internal protection circuit and stop supply of power.In this case the Fuse will self-rest after a couple of minutes•The battery can be used in ambient temperature of - 20°C - + 55°C.Storage•Storage temperature range is - 20°C ~ + 35°C (<85% humidity).•To store the battery for a long period (longer than 4 Weeks), the battery should be charged between 50% and 75%. The battery should be recharged every 4 Weeks.•After storage some self-discharge will occur. Before re-use it is advisable to recharge the battery fully.Warranty•The V200 is covered by a 2 years unconditional warranty on all parts, except the cells.•The cells are covered by a 1 year warranty, 70% of the original capacity.•For warranty issues or if you have any additional questions, please contact the appropriate bebob distributor listed at www.bebob.de.Disposal•The V200 battery has to be disposed within a dedicated collection container for used device batteries. Please be aware that only empty batteries are allowed for disposal incollection containers. In case the battery is not completely discharged, precautions againsta potential short-circuit have to be taken.SpecificationsModel V200Mount V-MountCapacity 6,0Ah; 296WhVoltage 14,4V DCMaximum Output Voltage 16.8 V DCEnd Voltage 12.0 VCells Lithium-Ion Trimix made in JapanMax. Discharge Current 16.0ATwist D-Tap 14.4V unreg. Max. 35WUSB Port 5V, 1.0AFuel Gauge 5-Step LEDWeight 1.0 KgDimensions (WXHXD) 94x144x58mmChargers bebob, idx, sonyCharging time (bebob VS2/VS4) 4 HoursOperating Temp. Range Charge: + 10°C ~ + 30°C recommendedDischarge:- 20°C ~ + 55°CStorage:- 20°C ~ + 35°C (<85% RH )Transport as of April 1st 2016•This Summary reflects our current Knowledge.1. Transport by Commercial Airline / Carry-on Luggage•V200 are forbidden in your carry-on luggage2. Transport by Commercial Airline / Checked-in Luggage•V200 are forbidden in your Checked-in luggage3. Transport as air-, road- and sea-freight•Li-Ion batteries, and so bebob V200, when shipped by air, road or sea are classified as dangerous goods class 9 and subject to special UN certified packaging.•Air transport authority training and authorisation (PK 1/ PK 2) are required for packing V200, for an air cargo shipment.•Li-Ion batteries for air cargo must have a state-of-charge of no more than 30% for shipping, means only one out of the five fuel gauge led lights up.•We recommend that you confirm with your carrier of choice, to determine any further restriction or local policies, before travelling. You will find the actual regulation ofyour carrier of choice in the bebob transport information system www.fly-,。