质量管理相关英语大全

（质量管理知识）质量英语词汇大全(完整版)品质名词（中英对照）AABC analysis ABC 分析Abnormality 不正常性Abscissa 横坐标Absolute deviation 绝对离差Absolute dispersion 绝对离势Absolute error 绝对误差Absolute frequency 绝对次数Absolute number 绝对数Absolute reliability 绝对可靠度Absolute term 绝对项Absolute value 绝对值Absolute variation 绝对变异Abstract number 抽象数Abstract unit 抽象单位Accelerated factor 加速系数，加速因子Accelerated life test 加速寿命试验Accelerated test 加速试验Acceleration 加速度Acceptable limit 允收界限Acceptable process 允收制程水平Acceptable quality 允收品质Acceptable quality level (AQL) 允收质量水平Acceptable reliability level (ARL) 允收可靠度水平Acceptability 允收性Acceptability criterion 允收标准Acceptance 允收，验收Acceptance, probability of 允收机率Acceptance, region of 允收区域Acceptance and rejection criteria 允收与拒收准则Acceptance boundary 允收界限Acceptance coefficient 允收系数Acceptance control chart 验收管制图Acceptance cost 验收费用Acceptance criteria 允收准则Acceptance error 允收误差Acceptance inspection 验收检验Acceptance limit 允收界限Acceptance line 允收线Acceptance number 允收（不良品）数Acceptance plan 验收计划Acceptance procedure 验收程序Acceptance/rectification scheme 允收/精选方案Acceptance sampling, attribute 计数值验收抽样Acceptance sampling, variable 计量值验收抽样Acceptance sampling plan 验收抽样计划Acceptance sampling scheme 验收抽样方案Acceptance test 验收试验Acceptance value 允收值Acceptance zone 允收区域Acceptance product 允收品Accepting lot 允收批Access time 接近时间，故障诊断时间Accessibility 可接近性Accident rate 意外率Accidental error 偶误，偶然误差Accidental fluctuation 偶然波动Accidental movement 意外移动Accounting test 验算（决算）试验Accumulated operating time 累积操作时间Accuracy 准确度Accuracy of data 数据准确度Accuracy of estimation 估计准确度Accuracy of the mean 平均数准确度Achieved availability 实际可用度Action 行动，措施Action, corrective 矫正行动（措施）Action control chart 行动管制图Action limit 行动界限Active line 行动线Active maintenance time 实际维护时间Active parallel redundancy 主动并复联（置）Active preventive maintenance 现行预防维护时间Active redundancy 主动复联（置）Active repair time 实际修复时间Active standby 主动备用Active time 运用时间Actual frequency 实际次数Actual limit 实际界限Actual range 实际全距Actual value 实际值Adaptability 可适应性Adaptive control 修改管制Addition theorem 加法定理Additivity 加法性，可加性Adjusted average 修正平均数Adjusted value 修正值Adjustment factor 调整系数Administration time for a repair 修复之管理时间Administrative time 管理时间Adopted value 采用值Advisory Group on Reliability of Electronic Equipment (AGREE)电子装备可靠度顾问团Aeronautical Radio, Incorporated (ARINC) 航空无线电公司After-sales service 售后服务Age 年限Age at death 死亡年限Age at failure 失效年限Age-based maintenance 年限基准维护Aggregative method 综合法Aging 老化Agreement of quality assurance 质量保证之协议Agreement on verification method 验（查）证方法之协议Alarm signals 警告（报）讯号Alert time 待命时间Algebraic sum 代数和Algorism (Algorithm) 阿拉伯数字计数法Alias 假名Alienation 余相关Alignment chart 列线图Allocation 配当Allocation of reliability 可靠度配当Allowable percent defective (Acceptable quality level, AQL) 允收不良率（允收质量水平）Allowance 允差，裕度Alternative hypothesis 对立假设American Management Association (AMA) 美国管理协会American National Standards Institute (ANSI) 美国标准协会American Society for Quality Control (ASQC) 美国质量管理学会American Society for Mechanical Engineers (ASME) 美国机械工程师学会American Society for Testing and Materials (ASTM) 美国材料试验学会American Standard Association (ASA) 美国标准协会American Statistical Association (ASA) 美国统计协会American War Standards (AWS) 美国战时标准Ambient condition 周遭条件Analysis, sequential 逐次分析Analysis by accumulated frequency 累积法，累积次数分析Analysis by non-accumulated frequency 次数法，非累积次数分析Analysis of correlation 相关分析Analysis of covariance 共变异数分析Analysis of means (AVON) 平均数分析Analysis of problem 问题之分析Analysis of variance (ANOVA) 变异数分析Analysis sample 分析样本Analytical error 分析误差Angular transformation 角度转（变）换Anti-logarithm 逆对数Anti-mode 逆众数AOQL Sampling Table 平均出厂质量界限抽样数Applicability 应用性Applied statistics 应用统计学Apportionment of reliability 可靠度配当Apportionment techniques 配当技术Appraisal cost 鉴定成本，评估成本Appraisal system 评估制度Appraisal of quality 质量评估Approach to sequential testing 逐次试验法Approval of processes and equipment 核准制程与设备Approximate mode 近似众数Approximate number 近似数值Approximation 近似法，概算AQL (Acceptable quality level) 允收（质量）水平Arbitrary average (Assumed average，Arbitrary mean) 假定平均数Arbitrary origin 假定原点Arbitrary scale 假定标度Area bar chart 面积条图Area chart (diagram, graph) 面积图Area sampling 地区抽样Arithmetic average 算术平均数Arithmetic cross 算术交叉Arithmetic graph 算术图Arithmetic line chart 算术线图Arithmetic mean 算术平均数Arithmetic paper 算术纸Arithmetic probability paper 算术机率纸Arithmetic progression (Arithmetic series) 算术级数，等差级数Arithmetic scale 算术标度，等差标度Arithmetic series 算术级数，等差级数Army Ordnance Table 陆军兵工署（抽样）表Army Service Forces Table 陆军（抽样）表序列Array 序列Array distribution 序列分配（布）Array of data 数据序列Assemble 装配（组立）Assembled product 装配品Assembly 装配件Assembly inspection 装配检验Assembly quality analysis report 装配质量分析报告Assessed failure rate 评估失效率Assessed mean active -maintenance time 评估时间现行维护时间Assessed mean life 评估平均寿命Assessed mean time between failures 评估平均失效间格时间Assessed mean time to failure 评估平均失效前时间Assessed reliability 评估可靠度Assessed value 评估值Assessment of subcontractor 分包商之评鉴Assignable cause (Special cause) 非机遇原因（特殊原因）Assignable variation 非机遇变异Associated dependent variable 相联因变数Associated variate 相联变量Association coefficient 相联系数Association of attribute 品性相联Association table 相联表，联合表Assumed mean (Assumed average，Arbitrary average) 假定平均数Assumed median 假定中位数Assumed origin 假定原点Assurance quality 保证质量Assurance function 保证功能Asymmetrical distribution 不对称分配（布）Asymmetry 不对称Asymptotic distribution 趋近分配（布)At random 随机Attribute 计数值，属性Attribute classification 品性分类Attribute data 计数数据Attribute inspection 计数值检验Attribute sampling 计数值抽样Attribute sampling plan 计数值抽样计划Attribute testing (Go no-go testing) 计数值试验（通过与不通过试验）Attribute value 计数值Audit 稽核Audit for reliability 可靠度稽核Audit of decision 稽核决策Audit plan 稽核计划Audit report 稽核报告Auditing report 稽核报告Auto-correlation 自动相关Automatic switch-over redundancy 自动切换复联（置）Automatic test equipment (Am) 自动试验装备Auto-regression 自动回归Availability 可用性，可用度Average (Mean) 平均数，平均值Average, grand 总平均Average, moving 移动平均数Average, sample 样本平均数Average, standard error of 标准误平均数Average, universe 群体平均数Average, weighted 加权平均数Average amount of inspection 平均检验数Average and range chart 平均数及全距（管制）图Average availability 平均可用度Average deviation (A.D.) (Mean deviation) 平均差Average error (Mean error) 平均误差Average number of defects 平均缺点数Average of ratios 比例平均数Average outgoing quality (AOQ) 平均出厂质量Average outgoing quality curve 平均出厂质量曲线Average outgoing quality level 平均出厂质量水平Average outgoing quality limit (AOQL) 平均出厂水平Average quality level 平均出厂质量界限Average quality level line 质量平均线Average quality protection 平均质量保护Average range 平均全距Average run length (ARL) 平均连串长度Average sample number (ASN)平均样品数Average range 平均全距Average run length (ARL) 平均连串长度Average sample number(ASN) 平均样本数Average sample number curve 平均样本曲线Average sample size (ASS) 平均样本大小Average sample size curve 平均样本大小曲线Average sample 平均抽样Average total inspection (ATI) 平均总检验（件）数Average total inspection curve 平均总检验数曲线Average value 平均值Avoidable cause 可避免之原因Avoidable quality cost 可避免之质量成本Axiom 公理Axis 轴Axis of abscissa 横轴Axis of ordinate 纵轴BBad lot 坏批Balance frequency 平衡次数Balanced complete type 平衡完备型Balanced design 平衡设计Balanced experiment 平衡实验Balanced incomplete type 平衡不完备型Balanced sample 平衡样本Band chart 带形图Band curve chart 带形曲线图Bank of reliability data 可靠度数据库Bar chart (diagram) 条（形）图Bartlett's test 巴特莱特试验Base line 基线Base number 基数Base period 基期Base point 基点Basic reliability 基本可靠度Batch (Lot) 批Batch of material 材料批Batch process 分批制造方法Batch size 批量Batch testing 批试验Bathtub curve 浴缸曲线Bathtub failure curve 浴缸失效曲线Bayes' estimator 贝式估计式Bayes' theorem 贝式定理Bayesian approach 贝式法Bayesian approcah to design 贝式设计法Bayesian estimation 贝式估计Bead map 标珠图Bell-shaped curve 钟形曲线Bell-shaped distribution 钟形分配（布）Bell-shaped failure pattern 钟形失效型态Bell System 贝尔系统Bell Telephone Laboratories 贝尔电话实验室Bell Telephone Laboratories Sampling Table 贝尔（电话实验室）抽样表Benign failure 无危险的失效Bernoulli distribution 白努利分配（布）Best fit 最适配合Best fitting line 最适线Best fitting curve 最适曲线Best linear invariant estimator 最佳线型不变估计式Best linear unbiased estimator 最佳线型不偏估计式Beta coefficient β系数Beta distribution β分配（布）Beta function β函数Between-class variance 组间变异数Between-column variance 组间变异Between-column variation 行间变异Between-row variation 列间变异Between sample variation 样本间变异Bias 偏差Bias, downward 向下偏差Bias, downward type 向下型偏差Bias, upward 向上偏差Bias, upward type 向上型偏差Biased error 偏误Biased estimate 偏差估计Biased sample 偏差样本Biased test 偏差试验Bilateral 双边Bill of material (BOM) 物料清单Bimodal 双峰Bimodal curve 双峰曲线Bimodal distribution 双峰分配（布）Bimodal redundancy 双峰型复联（置）Bimodality 双峰性Binary system 二元制Binomial, skewed 偏态二项Binomial coefficient 二项系数Binomial curve 二项曲线Binomial distribution 二项分配（布）Binomial equation 二项方程式Binomial expansion 二项展开式Binomial population 二项群体Binomial probability distribution 二项机率分配（布）Binomial probability paper(BIPP) 二项机率纸Binomial series 二项级数Binomial theorem 二项定理Bi-serial 双数列Biserial correlation 双数列相关Biserial coefficient of correlation 双数列相关系数Biserial ratio of correlation 双数列相关比Bivariate 双变量Bivariate distribution 双变量分配（布）Bivariate frequency distribution 双变量次数分配（布）Bivariate normal distribution 双变量常态分配（布）Blend 混，混合Block 量块，（实验）区，方块Block design 实验区设计Block diagram 方块图Block factor 地区因素Block in series 串联方块Boundary 界Boundary, cell 组界Bowker-Goode variables plan Bowker-Goode 记量值（抽样）计划Bowl drawing 碗珠抽样Bowl experiment 碗珠实验Bowl test 碗珠试验Bowley's coefficient of skewness Bowley偏态系数Bowley's formula Bowley公式Bureau of Ordnance, U.S. Navy 美国海军兵工署Break-even chart 损益平衡图Break-even point (BEP) 损益平衡点Breakthrough 突破British Standards Institution 英国标准协会Broken curve 中断曲线Broken series 中断数列Broken trend 中断趋势Built-in test (BIT) 内含测试，自测Bureau of Commodity Inspection and Quarantine (BCIQ) 商品检验局Bulk sampling Burn-in 大宗抽样Business Process Management (BPM) 业务流程管理Buyer 买方，客户CC chart C（管制）图Calculated value (Computed value) 计算值Calculation chart 计算图Calendar time 日历时间Calibration 校正Calibration record 校正记录Camp-Meidell inequality Camp-Meidell不等式Capability 能力Capability, machine 机器能力Capability, process 制程能力Capability ratio 能力比Capacity 能量，容量Caption 纵标目Carrying out the audit 实施稽核Cartogram 统计图Case method 个案法Catastrophic failure 突然故障，崩坏失效，致命失效Category 类别Cauchy distribution Cauchy 分配（布）Causality 因果律Cause 原因Cause, assignable 非机遇原因Cause, avoidable 可避免原因Cause, chance 机遇原因Cause, common 共同原因Cause, findable 可寻找原因Cause, random 随机原因Cause, special 特殊原因Cause, substantial 本质原因Cause, unavoidable 不可避免原因Cause and effect 因果Cause and effect diagram 特性要因图Cell 组Cell boundary 组界Cell deviation (d) 组离差Cell frequency (f) 组次数Cell interval (i,h) 组距Cell limit 组限Cell method 分组法Cell mid-point (Xm) 组中点Cell value 组值Censored sample 检剔样本Censored test 检剔试验Censorship 检剔Census 普查Center line 中线Central inspection station 中央检验站Central limit theory 趋中理论，中央极限理论Central limit theorem 趋中理论，中央极限理论Central line (CL.) 中心线Central moment 中心动差Central ordinate 中纵坐标Central tendency 集中趋势Central value 中值，中心值Certainty 确定性Certified chart 验证图Certified equipment 合格设备Certified quality engineer (CQE) 合格质量工程师Certified quality technician (CQT) 合格质量技术师Certified reliability engineer (CRE) 合格可靠度工程师Certification 验证Chain model 炼结模型Chain reliability 炼结可靠度Chain sampling plan (CHSP) 炼结抽样计划Chance 机遇Chance cause 机遇原因Chance error (Probable error) 机遇误差，机误Chance factor 机遇因素Chance failure 机遇故障，机遇失效Chance failure period 机遇失效期Chance fluctuation 机遇波动Chance variable 机遇变数Chance variation 机遇变异Change control 改变（变更）管理Chaotic variation 混乱变异Characteristic （质量）特性Characteristic, qualitative 质的特性Characteristic, quantitative 量的特性Characteristic curve, operating (OC curve) 操作特性曲线，OC曲线Characteristic diagram 特性要因图Characteristic function 特性函数Characteristic life 特性寿命Characteristic operating curve (OC curve) 特性操作曲线（OC曲线）Characteristic value 特性值Chargeable failure 可计列失效，故障Charlier check Charlier 覆检法Chart 图，（管制）图Chart, acceptance control 验收管制图Chart, average and range 平均数及全距（管制）图Chart, average number of defects 平均缺点数（管制）图Chart, control 管制图Chart, cumulative sum 累积和（管制）图Chart, defects per unit 每单位内缺点数（管制）图Chart, fraction defective 不良率（管制）图Chart, group 多项（管制)图Chart, individual 个别值（管制）图Chart, median 中位数（管制）图Chart, moving and range 移动平均数及全距（管制）图Chart, moving range 移动全距（管制）图Chart, modified control limits 修正管制界限（管制）图Chart, multi-variation 变异值（管制）图Chart, multiple 复式（管制）图Chart, number defectives 不良（品）数（管制）图Chart, number of defects 缺点数（管制）图Chart, percent defective 不良率管制图Chart, range 全距（管制）图Chart, run 操作（记录）图Chart, shop 工厂（管制）图Chart, Shewhart control Shewhart 管制图Chart, two-way control 双向管制图Chebyshev's inequality Chebyshev 不等式Check inspection 复核检验Check sampling 复核检验员Check inspector 复核抽样Chi-square ，卡方Chi-square distribution 分配（布），卡方分配（布）Chi-square test 检定，卡方检定Chi-squared distribution 分配（布），卡方分配(布）Chip 小圆片Chronic defect 慢性缺点Chronological chart 时序图Chronological series 时序数列Class 组Class boundaries (True class limits)组界（真实组限）Class form 组形Class frequency (f) 组次数Class interval (i,h) 组距Class limit 组限Class mark 组标，中值Class mean 组平均数Class mid-point(Xm) 组中点Class mid-value 组中值Class of median 组中位数Class value 组值Classes, number of 组数Classification chart 分组，分类Classification frequency 分组次数Classification frequency series 分组次数数列Classification of defectives 不良品分类Classification of defects 缺点分类Classfication of failure 失效分类，故障分类Classification process 分组（方）法Clearance 间隙，余隙Cluster 集团Cluster sampling 集团抽样Cochran's test Cochran 检定Code 简化，代号Code letter 代字Coded unit 简化单位Coded value 简化值Coding 简化Coding rule 简化规则Coefficient 系数Coefficient, correlation 相关系数Coefficient of alienation 余相关系数Coefficient of association 相关系数Coefficient of binomial distribution 二项分配（布）系数Coefficient of colligation 束联系数Coefficient of contingency 列联系数Coefficient of correlation 相关系数Coefficient of determination (r2) 定限系数Coefficient of dispersion 离势系数Coefficient of kurtosis 峰度系数Coefficient of multiple correlation 复相关系数Coefficient of net correlation 净相关系数Coefficient of net regression 净回归系数Coefficient of non-determination 不定限系数Coefficient of part correlation 部份相关系数Coefficient of partial correlation 部份相关系数Coefficient of rank correlation 等级相关系数Coefficient of reliability 可靠度系数Coefficient of regression 回归系数Coefficient of skewness 偏态系数，偏斜系数Coefficient of variation (CV) 变异系数Cold standby 冷置系数Collective quality 集体品质Columbia sampling table Columbia 抽样计划Column (Column/Row) 行，纵行（行/列）Column head 标目Column diagram 直行图Combination 组合Combinational model 复合模型Combined environmental reliability test (CERT) 复合环境可靠度试验Combined failure 复合失效，复合故障Combined stress life test 复合应力寿命试验Commissioning 委制Commodity 商品Common cause (Chance cause) 共同原因（机遇原因）Company standard 公司标准Companys need 公司需要Company-wide quality control (CWQC) 全公司质量管理Comparability 可比性Comparable measure 可比量数Compensating error 补偿误差Compensating fluctuation 补偿波动Competing product 竞争产品Complete association 全相联Complete block design 完全区集法Complete confounding 完全交络Complete dissociation 全不相联Complete failure 完全故障，完全失效Completely randomized design 完全随机法Complaint 抱怨Complaint index 抱怨指标Completed product verification 成品验证Component 组件，组件Component bar chart 成份条图Component distiibution 组成份分配（布）Component part diagram 成份图Component ratio 成份比Component reliability 组件可靠度Component variance 成份变异数Components of variance 变异数成份Composite curve 复合曲线Composite design 复合法Composite hypothesis 复合假设，组合假设Composite unit 复合单位Compound distribution 复合分配（布）Compound event 复合事件Compound probability 复合机率Compounding technique 复合法Compressed limit 压缩界限Compressed limit gauging 压缩界限规则Computed value 计算值Concentric circle diagram 同心圆图Conception of limit 极限概念Conceptual design 概念设计Conceptual design review 概念设计审查Concession 特采，特认Concomitant factor 共变因素Concomitant variable 共变数Concomitant variation 共变异Concurrency 并行Condition maintenance 状态维护Condition monitoring 状态监督Condition-based maintenance 状态基准维护Conditional probability 条件机率Conditions of use 使用条件Confidence 信任，信赖Confidence coefficient 信任系数，信赖系数Confidence interval 信任区间，信赖区间Confidence in test results 试验结果的信赖度Confidence level 信任水平，信赖水平Confidence limit 信任界限，信赖界限Confidence range 信任全距，信赖全距Configuration control 型态管制Configuration items 型态件Configuration management 型态管理Confirmation 确认Conformance to the requirement 符合要求Conformation 一致Conforming article 合格品Conformity 符合Confounding 交络Confounding, complete 完全交络Confounding, partial 部份交络Connector 连接器Consignment 委托，寄售Consistency 一致性Constancy 恒久性Constancy of great numbers 大数恒久性Constant 常数Constant cause system 恒常原因系统Constant error 恒常误差Constant failure period 恒常失效期Constant failure rate dustribution 恒常失效率分配（布）Constant weight (Fixed weight) 固定权数Constraint 束缚Consultant 管理顾问师Consumer 消费者Consumer acceptance specification 消费者允收规格Consumerism 消费者主义Consumer's risk (CR) 消费者冒险率Consumer test panel 消费者试验小组Consumer preference 消费者偏好Consumer sensitivity test 消费者感官试验Contingency 列联Contingency coefficient 列联系数Contingency table 列联表Contingency theorem 列联理论Continuity correction 连续校正Continuous change 连续变更Continuous data 连续数据Continuous distribution 连续分配（布）Continuous production 连续生产Continuous sampling 连续抽样Continuous sampling plan (CSP) 连续抽样计划Continuous series 连续数列Continuous variable 连续变量Contract 合约Contract preparation 拟定合约Contract review 合约检讨Contract requirements 合约需求Contract requirements analysis 合约需求分析Contractors 合约商Contrast analysis 对照分析Control, in 在管制（状态）下Control, lack of 缺乏管制Control, out of 超出管制Control, state of 管制状态Control, under 在管制（状态）下Control chart 管制图Control chart, cumulative sum 累积和管制图Control chart, defects per unit 每单位内缺点数管制图Control chart, two-way 双向管制图Control chart factor 管制图系数Control chart for attribute 计数值管制图Control chart for variable (measurement) 计量值管制图Control chart method 管制图法Control chart pattern 管制图类型Control gaging (gauging) 管制规测Control level 管制水平Control limit 管制界限Control limit, lower 管制下限Control limit, modified 修正管制界限Control limit, upper 管制上限Control limit factor 管制界限因子Control line 管制线Control of measuring and test equipment 量测与试验设备之管制Control of nonconforming material 不合格物料之管制Control of nonconforming product 不合格产品之管制Control of production 生产管制Control of reliability 可靠度管制Control of verification status 验证状况之管制Control plan 管制计划Control point 管制点Control station 管制站Control system 管制系统Controlled process 管制制程Controlled state 管制状态Controlled variability 管制变异性Controlled variable 管制变数Controlling item 管制项目Convenience lot 合宜的批Convergence 收敛Cooked distribution 中断分配（布）Coordinate 坐标Coordinate axis 坐标轴Coordinate line 坐标线Coordination 协调Coordination for reliability 可靠度协调Correction 校正，修正Correction, Sheppard Sheppard 校正数Correction factor 修正因子Correction for continuity 连续校正Correction for mean 平均数校正Correction term 校正项Corrective action 矫正行动，改正措施Corrective maintenance 矫正维护，改正维护Corrective maintenance time 矫正维护时间，改正维护时间Corrective sorting 修正选别Correlated measure 相关量数Correlated samples 相关样本Correlation 相关Correlation, coefficient of 相关系数Correlation, direct 直接相关Correlation, index of 相关指数Correlation, inverse 反相关Correlation, multiple 复相关Correlation, negative 负相关Correlation, net 净相关Correlation, nonlinear 非线性相关Correlation, nonsense 无意义相关Correlation, part 部份相关，偏相关Correlation, partial 部份相关，偏相关Correlation, perfect 完全相关Correlation, rank 等级相关Correlation, serial 数序相关Correlation, simple 简相关Correlation, zero 零相关Correlation analysis 相关分析Correlation chart 相关图Correlation, coefficient 相关系数Correlation coefficient, rank 等级相关系数Correlation matrix 相关矩阵Correlation of attributes 品性相关Correlation ratio 相关比Correlation of x on y x与y的相关比Correlation ratio of y on x y与x的相关比Correlation scatter chart 相关散布图Correlation surface 相关面Correlation table 相关表Correlation theory 相关理论Correlogram 相关图Corrosive atmosphere 腐蚀性空气Cost 成本，费用Cost, acquisition 取得成本Cost, appraisal 评估（鉴定）成本Cost, external failure 外部失败成本Cost, internal failure 内部失败成本Cost, life cycle 寿命周期成本Cost, logistic 后续成本Cost, prevention 预防成本Cost, quality 质量成本Cost, quality control 质量管理成本Cost, rework 重加工成本Cost effectiveness 成本效益Cost function 成本机能Cost model for reliability optimization 可靠度最佳化成本模式Cost reduction 成本减低Count (Countable) data 点计数据Counter variation 反行变异Co-variation 共变异Covariance 共变异数，共变数Covariance analysis 共变异数分析Covariance matrix 共变异矩阵Craps, game of 掷骰游戏Credibility 信用Creep failure 潜变失效，潜变故障Crest 峰Criteria for workmanship 工作技艺准则Criterion 准则，规范Criterion, acceptance 验收准则（规范）Critical component control 重要组件管制Critical defect 严重缺点Critical defective 严重不良品Critical design review 关键设计审查Critical failure 关键故障，严重失效Critical items 关键品目，重要件Critical path 要径Critical path analysis 要径分析法Critical region 临界区域，弃却区域，判定区Critical value 临界值，判定值Criticality 严重性，关键性Cross 交叉Cross check 互校Cross classification 交叉分类Cross correlation 交叉相关Cross formula 交互公式Cross-hatch 交叉线Cross-hatched map 交叉图Cross-over design 交叉计划Crossed design 交叉法Crude mode 概括众数Crude moment 概括动差Cubic chart (diagram) 立方图Culled 检选Cumulant 累积数Cumulation, downward 向下累积Cumulation, total 全部累积Cumulation, upward 向上累积Cumulation average chart 累积平均数（管制）图Cumulative curve 累积曲线Cumulative curve chart 累积曲线图Cumulative damage 累积损坏Cumulative distribution (Ogive) 累积分配（布）Cumulative distribution function 累积分配（布）函数Cumulative error 累积误差Cumulative failure frequency 累积故障次数，累积失效次数Cumulative frequency 累积次数Cumulative frequency arrangement 累积次数排列Cumulative frequency curve 累积次数曲线Cumulative frequency 累积次数曲线图Cumulative frequency distribution 累积次数分配（布）Cumulative frequency polygon 累积（次数）多边形Cumulative frequency (probability) function 累积次数（机率）函数Cumulative frequency table 累积次数表Cumulative function 累积函数Cumulative graph 累积图Cumulative hazard function 累积冒险函数Cumulative mean 累积平均数Cumulative normal distribution 累积常态分配Cumulative number of failures 累积失效数，累积故障数Cumulative percentage of failures 累积失效百分率，累积故障百分率Cumulative probability distribution 累积机率分配（布）Cumulative sum 累积和Cumulative sum chart 累积和（管制）图Cumulative sum control chart 累积和管制图Cumulative terms 累积项Curtailed (Truncated) inspection 截略检验Curtailed (Truncated) sample inspection截略样品检验Curtailed sampling 截略抽样Curtailed sampling inspection 截略抽样检验Curtaijed sampling plan 截略抽样计划Curtailment of sampling plan 抽样计划之截略Curve 曲线Curve, frequency 次数曲线Curve, normal 常态曲线Curve chart (diagram) 曲线图Curve fitting 曲线配合Curve of error 误差曲线Curve of means 平均数曲线Curve of probability 机率曲线Curve type criterion 曲线型准则Curve shape 曲线形状Curvilinear correlation 曲线相关Curvilinear regression 曲线回归Curvilinear trend 曲线趋势Curvilinearity 曲线性Customer 客户，顾客Customer complaint 顾客抱怨Customer feedback information 顾客回馈信息Customer incurred cost 顾客引发成本Customer operation cost 顾客作业成本Customer repair cost 顾客修理成本Customer requirement 顾客要求Customer satisfaction 顾客满意度Customer's need 顾客需要Cusum chart 累积和（管制）图Cycles 周期Cycles between failures 失效间隔周期，故障间隔周期Cycle of operation 操作周期Cyclic curve 周期（循环）曲线Cyclic damage 周期性损坏Cyclic load 周期性负荷Cyclical deviation 周期（循环）离差Cyclical fluctuation 周期波动Cyclical trend 周期趋势Cyclical movement 周期移动Cyclical variation 周期变异Cycling failure rate 周期性失效率，周期性故障率DD chart d管制图Data 数据Data analysis 数据分析Data bank 资料室（库）Data exchange program 数据交换计划Data, inspection 检验数据Data item 数据项，文件项目Data processing 数据处理Death rate 死亡率Debug (debugging) 除错Decile 十分位数Decimal fraction 小数Decision function 决策函数Decision line 决定线Decision making 决策Decision variable 决策变数Decreasing failure rate distribution 递减失效率分配(布）Decrement 减量Decrement rate 减率Defect 疵病，缺点Defect, chronic 慢性缺点。

【常见质量管理术语英文缩写】1、PDCA：Plan、Do、Check、Action；策划、实施、检查、处置2、PPAP：Production Part Approval Process；生产件批准程序3、APQP：Advanced Product Quality Planning；产品质量先期策划4、FMEA：Potential Failure Mode and Effects Analysis 潜在失效模式及后果分析5、SPC：Statistical Process Control 统计过程控制6、MSA：Measurement System Analysis 测量系统控制7、CP：Control Plan 控制计划8、QSA：Quality System Assessment 质量体系评定9、PPM：Parts Per Million 每百万零件不合格数10、QM：Quality Manua 质量手册11、QP：Quality Procedure 质量程序文件Quality Planning 质量策划Quality Plan 质量计划12、CMK：机器能力指数13、CPK：过程能力指数14、CAD：Computer-Aided Design 计算机辅助能力设计15、OEE：Overall Equipment Effectiveness 设备总效率16、QFD：Quality Function Deployment 质量功能展开17、FIFO：First in, First out 先进先出18、COPS：Customer Oriented Processes 顾客导向过程19、TCQ： Time、Cost、Quality 时间、成本、质量20、MPS：Management Processes 管理性过程21、SPS：Support Processes 支持性过程22、TQM：Total Quality Management 全面质量管理23、PQA：Product Quality Assurance 产品质量保证（免检）24、QP-QC-QI：质量三步曲质量计划－质量控制－质量改进25、QAF：Quality Assurance File 质量保证文件26、QAP：Quality Assurance Plan 质量保证计划27、PFC：Process Flow Chart 过程流程图28、QMS：Quality Management Systems 质量管理体系29、JIT：Just In Time 准时（交货）30、ERP：Enterprise Requirement Planning 企业需求计划31、QC：Quality Control 质量控制32、QA：Quality Audit 质量审核Quality Assurance 质量保证33、IQC:In come Quality Control 进货质量控制34、IPQC:In Process Quality Control 过程质量控制35、FQC:Final Quality Control 成品质量控制36、OQC:Out Quality Control 出货质量控制37、4M1E:Man、Machine、Material、Method、Environment 人、机、料、法、环38、5W1H：Why、What、Who、When、Where、How 为何/做什么/谁做/时间/地点/如何做39、6S：Seiri、Seiton、Seiso、Seiketsu、Shitsuke、Safety 整理、整顿、清扫、清洁、素养、安全40、TRI值：Total Record Injury （三种）可记录工伤值41、SMART精明原则：Specific Measurable Achievable Result Oriented Timed 具体的描述、可以测量的、可以通过努力实现的、有结果导向性的、有时间性的【企业常用英文缩写】42、5S : 5S管理43、ABC : 作业制成本制度 (Activity-Based Costing)44、ABB : 实施作业制预算制度 (Activity-Based Budgeting)45、ABM : 作业制成本管理 (Activity-Base Management)46、APS : 先进规画与排程系统 (Advanced Planning and Scheduling)47、ASP : 应用程序服务供货商（Application Service Provider）48、ATP : 可承诺量 (Available To Promise)49、AVL : 认可的供货商清单(Approved Vendor List)49、BOM : 物料清单 (Bill Of Material)50、BPR : 企业流程再造 (Business Process Reengineering)51、BSC : 平衡记分卡 (Balanced ScoreCard)52、BTF : 计划生产 (Build To Forecast)53、BTO : 订单生产 (Build To Order)54、CPM : 要径法 (Critical Path Method)55、CPM : 每一百万个使用者会有几次抱怨(Complaint per Million)56、CRM : 客户关系管理 (Customer Relationship Management)57、CRP : 产能需求规划 (Capacity Requirements Planning)58、CTO : 客制化生产 (Configuration To Order)59、DBR : 限制驱导式排程法 (Drum-Buffer-Rope)60、DMT : 成熟度验证(Design Maturing Testing)61、DVT : 设计验证(Design Verification Testing)62、DRP : 运销资源计划 (Distribution Resource Planning)63、DSS : 决策支持系统 (Decision Support System)64、EC : 设计变更／工程变更 (Engineer Change)65、EC : 电子商务 (Electronic Commerce)66、ECRN : 原件规格更改通知(Engineer Change Request Notice)67、EDI : 电子数据交换 (Electronic Data Interchange)68、EIS : 主管决策系统 (Executive Information System)69、EMC : 电磁相容(Electric Magnetic Capability)70、EOQ : 基本经济订购量 (Economic Order Quantity)71、ERP : 企业资源规划 (Enterprise Resource Planning)72、FAE : 应用工程师(Field Application Engineer)73、FCST : 预估(Forecast)74、FMS : 弹性制造系统 (Flexible Manufacture System)75、FQC : 成品质量管理 (Finish or Final Quality Control)76、IPQC: 制程质量管理 (In-Process Quality Control)77、IQC : 进料质量管理 (Incoming Quality Control)78、ISO : 国际标准组织 (International Organization for Standardization)79、ISAR: 首批样品认可(Initial Sample Approval Request)80、JIT : 实时管理 (Just In Time)81、KM：知识管理 (Knowledge Management)82、 L4L : 逐批订购法 (Lot-for-Lot)83、LTC : 最小总成本法 (Least Total Cost)84、LUC : 最小单位成本 (Least Unit Cost)85、MES : 制造执行系统 (Manufacturing Execution System)86、MO : 制令(Manufacture Order)87、MPS : 主生产排程 (Master Production Schedule)88、MRO : 请修(购)单(Maintenance Repair Operation)89、MRP : 物料需求规划 (Material Requirement Planning)90、MRPII : 制造资源计划 (Manufacturing Resource Planning)91、NFCF : 更改预估量的通知Notice for Changing Forecast92、OEM : 委托代工 (Original Equipment Manufacture)93、ODM : 委托设计与制造 (Original Design & Manufacture)94、OLAP : 在线分析处理 (On-Line Analytical Processing)95、OLTP : 在线交易处理 (On-Line Transaction Processing)96、OPT : 最佳生产技术 (Optimized Production Technology)97、OQC : 出货质量管理 (Out-going Quality Control)98、PDCA : PDCA管理循环 (Plan-Do-Check-Action)99、PDM : 产品数据管理系统 (Product Data Management)100、PERT : 计划评核术 (Program Evaluation and Review Technique)91、PO : 订单(Purchase Order)92、POH : 预估在手量 (Product on Hand)93、PR : 采购申请Purchase Request94、QA : 品质保证(Quality Assurance)95、QC : 质量管理(Quality Control)96、QCC : 品管圈 (Quality Control Circle)97、QE : 品质工程(Quality Engineering)98、RCCP : 粗略产能规划 (Rough Cut Capacity Planning)99、RMA : 退货验收Returned Material Approval100、ROP : 再订购点 (Re-Order Point)101、SCM : 供应链管理 (Supply Chain Management)102、SFC : 现场控制 (Shop Floor Control)103、SIS : 策略信息系统 (Strategic Information System)104、SO : 订单(Sales Order)105、SOR : 特殊订单需求(Special Order Request)106、SPC : 统计制程管制 (Statistic Process Control)107、TOC : 限制理论 (Theory of Constraints)108、TPM : 全面生产管理Total Production Management109、TQC : 全面质量管理 (Total Quality Control)110、TQM : 全面品质管理 (Total Quality Management)111、WIP : 在制品 (Work In Process)。

500个质量管理专用中英文术语集锦质量必背——职业篇1.PDCA：Plan、Do、Check、Action 策划、实施、检查、处置2.PPAP：Production Part Approval Process生产件批准程序3.APQP：Advanced Product Quality Planning产品质量先期策划4.FMEA：Potential Failure Mode and Effects Analysis 潜在失效模式及后果分析5.SPC：Statistical Process Control统计过程控制6.MSA：Measurement System Analysis 测量系统控制7.CP：Control Plan 控制计划8.QSA：Quality System Assessment 质量体系评定9.PPM：Parts Per Million 每百万零件不合格数10.QM：Quality Mauna质量手册11.QP：Quality Procedure质量程序文件/Quality Planning质量策划/Quality Plan 质量计划12.CMK：机器能力指数13.CPK：过程能力指数14.CAD：Computer-Aided Design 计算机辅助能力设计15.OEE：Overall Equipment Effectiveness 设备总效率16.QFD：Quality Function Deployment质量功能展开17.FIFO：First in, First out先进先出18.COPS：Customer Oriented Processes顾客导向过程19.TCQ：Time、Cost、Quality时间、成本、质量20.MPS：Management Processes管理性过程21.SPS：Support Processes支持性过程22.TQM：Total Quality Management全面质量管理23.PQA：Product Quality Assurance产品质量保证（免检）24.QP-QC-QI：质量三步曲，质量计划－质量控制－质量改进25.QAF：Quality Assurance File质量保证文件26.QAP：Quality Assurance Plan质量保证计划27.PFC：Process Flow Chart过程流程图28.QMS：Quality Management Systems质量管理体系29.JIT：Just In Time准时（交货）30.ERP：Enterprise Requirement Planning企业需求计划31.QC：Quality Control 质量控制32.QA：Quality Audit 质量审核/Qality Assurance 质量保证33.IQC：In Come Quality Control 进货质量控制34.IPQC：In Process Quality Control 过程质量控制35.FQC：Final Quality Control 成品质量控制36.OQC：Out Quality Control 出货质量控制37.4M1E：Man、Machine、Material、Method、Environment人、机、料、法、环38.5W1H：Why、What、Who、When、Where、How 为何/做什么/谁做/时间/地点/如何做39.6S：Seiri、Seiton、Seiso、Seiketsu、Shitsuke、Safety 整理、整顿、清扫、清洁、素养、安全40.TRI值：Total Record Injury（三种）可记录工伤值41.SMART：精明原则，Specific Measurable Achievable Result Oriented Timed（具体的描述、可以测量的、可以通过努力实现的、有结果导向性的、有时间性的）质量必背——企业篇1.5S：5S管理2.ABC：作业制成本制度（Activity-Based Costing）3.ABB：实施作业制预算制度（Activity-Based Budgeting）4.ABM：作业制成本管理（Activity-Base Management）5.APS：先进规划与排程系统（Advanced Planning and Scheduling）6.ASP：应用程序服务供货商（Application Service Provider）7.ATP：可承诺量（Available To Promise）8.AVL：认可的供货商清单（Approved Vendor List）9.BOM：物料清单（Bill Of Material）10.BPR：企业流程再造（Business Process Reengineering）11.BSC：平衡记分卡（Balanced ScoreCard）12.BTF：计划生产（Build To Forecast）13.BTO：订单生产（Build To Order）14.CPM：要径法（Critical Path Method）15.CPM：每一百万个使用者会有几次抱怨（Complaint per Million）16.CRM：客户关系管理（Customer Relationship Management）17.CRP：产能需求规划（Capacity Requirements Planning）18.CTO：客制化生产（Configuration To Order）19.DBR：限制驱导式排程法（Drum-Buffer-Rope）20.DMT：成熟度验证（Design Maturing Testing）21.DVT：设计验证（Design Verification Testing）22.DRP：运销资源计划（Distribution Resource Planning）23.DSS：决策支持系统（Decision Support System）24.EC：设计变更/工程变更（Engineer Change）25.EC：电子商务（Electronic Commerce）26.ECRN：原件规格更改通知（Engineer Change Request Notice）27.EDI：电子数据交换（Electronic Data Interchange）28.EIS：主管决策系统（Executive Information System）29.EMC：电磁相容（Electric Magnetic Capability）30.EOQ：基本经济订购量（Economic Order Quantity）31.ERP：企业资源规划（Enterprise Resource Planning）32.FAE：应用工程师（Field Application Engineer）33.FCST：预估（Forecast）34.FMS：弹性制造系统（Flexible Manufacture System）35.FQC：成品质量管理（Finish or Final Quality Control）36.IPQC: 制程质量管理（In-Process Quality Control）37.IQC：进料质量管理（Incoming Quality Control）38.ISO：国际标准组织（International Organization for Standardization）39.ISAR：首批样品认可（Initial Sample Approval Request）40.JIT：实时管理（Just In Time）41.KM：知识管理（Knowledge Management）42.L4L：逐批订购法（Lot-for-Lot）43.LTC：最小总成本法（Least Total Cost）44.LUC：最小单位成本（Least Unit Cost）45.MES：制造执行系统（Manufacturing Execution System）46.MO：制令（Manufacture Order）47.MPS：主生产排程（Master Production Schedule）48.MRO：请修（购）单（Maintenance Repair Operation）49.MRP：物料需求规划（Material Requirement Planning）50.MRPII：制造资源计划（Manufacturing Resource Planning）51.NFCF：更改预估量的通知Notice for Changing Forecast52.OEM：委托代工（Original Equipment Manufacture）53.ODM：委托设计与制造（Original Design & Manufacture）54.OLAP：在线分析处理（On-Line Analytical Processing）55.OLTP：在线交易处理（On-Line Transaction Processing）56.OPT：最佳生产技术（Optimized Production Technology）57.OQC：出货质量管理（Out-going Quality Control）58.PDCA：PDCA管理循环（Plan-Do-Check-Action）59.PDM：产品数据管理系统（Product Data Management）60.PERT：计划评核术（Program Evaluation and Review Technique）61.PO：订单（Purchase Order）62.POH：预估在手量（Product on Hand）63.PR：采购申请（Purchase Request）64.QA：品质保证（Quality Assurance）65.QC：质量管理（Quality Control）66.QCC：品管圈（Quality Control Circle）67.QE：品质工程（Quality Engineering）68.RCCP：粗略产能规划（Rough Cut Capacity Planning）69.RMA：退货验收（Returned Material Approval）70.ROP：再订购点（Re-Order Point）71.SCM：供应链管理（Supply Chain Management）72.SFC：现场控制（Shop Floor Control）73.SIS：策略信息系统（Strategic Information System）74.SO：订单（Sales Order）75.SOR：特殊订单需求（Special Order Request）76.SPC：统计制程管制（Statistic Process Control）77.TOC：限制理论（Theory of Constraints）78.TPM：全面生产管理（Total Production Management）79.TQC：全面质量管理（Total Quality Control）80.TQM：全面品质管理（Total Quality Management）81.WIP：在制品（Work In Process）质量必背——部门篇QS: Quality system品质系统CS: Customer Service 客户服务QC: Quality control品质管理IQC: Incoming quality control 进料检验LQC: Line Quality Control 生产线品质控制IPQC: In process quality control 制程检验FQC: Final quality control 最终检验OQC: Outgoing quality control 出货检验QA: Quality assurance 品质保证SQA: Source(supplier) Quality Assurance 供应商品质保证(VQA) CQA：Customer Quality Assurance客户质量保证PQA rocess Quality Assurance 制程品质保证QE: Quality engineer 品质工程CE: component engineering零件工程EE: equipment engineering设备工程ME: manufacturing engineering制造工程TE: testing engineering测试工程PPE product Engineer 产品工程IE: Industrial engineer 工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC: producing control生管MC: mater control物管GAD: General Affairs Dept.总务部A/D: Accountant /Finance Dept.会计LAB: Laboratory实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department生产部PA:采购(PUR: Purchasing Dept.)SMT: Surface mount technology 表面粘着技术MFG: Manufacturing 制造MIS: Management information system 资迅管理系统DCC: document control center 文件管制中心质量必背——场内作业QT: Quality target品质目标QP: Quality policy目标方针QI: Quality improvement品质改善CRITICAL DEFECT:严重缺点（CR）MAJOR DEFECT:主要缺点（MA）MINOR DEFECT:次要缺点（MI）MAX: Maximum最大值MIN: Minimum最小值DIA diameter直径DIM dimension尺寸LCL: Lower control limit管制下限UCL: Upper control limit管制上限EMI:电磁干扰ESD:静电防护EPA:静电保护区域ECN:工程变更ECO: Engineering change order工程改动要求（客户）ECR:工程变更需求单CPI: Continuous Process Improvement 连续工序改善Compatibility：兼容性Marking：标记DWG drawing图面Standardization：标准化Consensus：一致Code：代码ZD: Zero defect零缺点Tolerance：公差Subject matter：主要事项Auditor：审核员BOM: Bill of material物料清单Rework：重工ID：identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR：First Piece Inspection Report首件检查报告FAA:首件确认SPC：统计制程管制CP: capability index（准确度）CPK: capability index of process(制程能力)PMP:制程管理计划（生产管制计划）MPI:制程分析DAS effects Analysis System 缺陷分析系统PPB：十亿分之一Flux：助焊剂P/N:料号L/N：Lot Number批号Version：版本Quantity：数量Valid date：有效日期MIL-STD：Military-Standard军用标准ICT: In Circuit Test (线路测试)ATE：Automatic Test Equipment自动测试设备MO: Manufacture Order生产单T/U: Touch Up (锡面修补)I/N:手插件P/T:初测F/T: Function Test (功能测试-终测)AS 组立P/K:包装TQM: Total quality control全面品质管理MDA: Manufacturing defect analysis制程不良分析(ICT) RUN-IN:老化实验HI-pot：高压测试FMI：Frequency Modulation Inspect高频测试DPPM: Defect Part Per Million(不良率的一种表达方式：百万分之一) 1000PPM即为0.1% Corrective Action: (CAR改善对策)ACC：允收REJ:拒收S/S：Sample size抽样检验样本大小SI-SIV：Special I-Special IV特殊抽样水平等级CON：Concession / Waive特采ISO:国际标准化组织ISA：Industry Standard Architecture工业标准体制结构OBA:开箱稽核FIFO:先进先出PDCA:管理循环Plan do check action计划，执行，检查，总结WIP:在制品（半成品）S/O: Sales Order (业务订单)P/O: Purchase Order (采购订单)P/R: Purchase Request (请购单)AQL: acceptable quality level允收品质水准LQL; Limiting quality level最低品质水准QVL: qualified vendor list合格供应商名册AVL ：认可的供货商清单(Approved Vendor List)QCD: Quality cost delivery（品质，交期，成本）MPM: Manufacturing project management制造专案管理KPI: Key performance indicate重要绩效指标MVT: Manufacturing Verification Test制造验证试产Q/R/S：Quality/Reliability/Service质量/可靠度/服务STL: ship to line（料到上线）NTF: No trouble found误判CIP: capacity improvement plan（产能改善计划）MRB: material review board（物料审核小组）MRB: Material reject bill退货单JIT: just in time（即时管理）5S:seiri seiton seiso seiketsu shitsuke（整理，整顿，清扫，清洁，修养）SOP: standard operation process（标准作业程序）SIP: Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction（作业指导书）SMD: surface mounting device（表面粘着原件）FAR: failure analysis report故障分析报告CAR: Corrective action report改善报告BPR：企业流程再造(Business Process Reengineering)ISAR ：首批样品认可(Initial Sample Approval Request)-JIT：实时管理(Just In Time)QCC ：品管圈(Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面品质环境管理)PD: Production Department (制造)LOG: Logistics (后勤支持)Shipping: (进出口)AOQ：Average Output Quality平均出货质量AOQL：Average Output Quality Level平均出货质量水平FMEA：failure model effectiveness analysis失效模式分析CRB: Change Review Board (工程变更会议)CSA：Customer Simulate Analysis客户模拟分析SQMS：Supplier Quality Management System供应商品质管理系统QIT: Quality Improvement Team 品质改善小组QIP：Quality Improvement Plan品质改善计划CIP：Continual Improvement Plan持续改善计划M.Q.F.S: Material Quality Feedback Sheet (来料品质回馈单) SCAR: Supplier Corrective Action Report (供货商改善对策报告)8D Sheet: 8 Disciplines sheet ( 8D单)PDCA：PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知)QAPS: Quality Assurance Process Sheet (品质工程表)DRP ：运销资源计划(Distribution Resource Planning)DSS：决策支持系统(Decision Support System)EC ：电子商务(Electronic Commerce)EDI ：电子资料交换(Electronic Data Interchange)EIS ：主管决策系统(Executive Information System)ＥＲＰ：企业资源规划(Enterprise Resource Planning)FMS ：弹性制造系统(Flexible Manufacture System)KM ：知识管理(Knowledge Management)4L ：逐批订购法(Lot-for-Lot)LTC ：最小总成本法(Least Total Cost)LUC ：最小单位成本(Least Unit Cost)MES ：制造执行系统(Manufacturing Execution System)MPS ：主生产排程(Master Production Schedule)MRP ：物料需求规划(Material Requirement Planning)MRPⅡ：制造资源计划(Manufacturing Resource Planning)OEM ：委托代工(Original Equipment Manufacture)ODM ：委托设计与制造(Original Design & Manufacture)OLAP：线上分析处理(On-Line Analytical Processing)OLTP：线上交易处理(On-Line Transaction Processing)OPT ：最佳生产技术(Optimized Production Technology)PDCA：PDCA管理循环(Plan-Do-Check-Action)PDM：产品数据管理系统(Product Data Management))RCCP：粗略产能规划(Rough Cut Capacity Planning)SCM ：供应链管理(Supply Chain Management)SFC ：现场控制(Shop Floor Control)TOC：限制理论(Theory of Constraints)TQC ：全面品质管制(Total Quality Control)FYI/R: For your information/reference仅供参考ASAP:尽快S/T: Standard time标准时间TPM: total production maintenance：全面生产保养ESD Wrist strap：静电环IT: information technology信息技术，资讯科学CEO：Chief Executive Officer执行总裁COO：Chief Operating Officer首席业务总裁SWOT：Strength, Weakness, Opportunity, Threat优势﹐弱点﹐机会﹐威胁Competence：专业能力Communication：有效沟通Cooperation：统御融合Vibration Testing：振动测试IDP：Individual Development Plan个人发展计划MRP：Material Requirement Planning物料需求计划MAT'S：Material材料LRR：Lot Reject Rate批退率ATIN：Attention知会3C：Computer ,Communication , Consumer electronic消费性电子5W1H：When , Where , Who , What , Why , Ho5M: Man , Machine , Material , Method , Measurement人,机器,材料,方法,测量4MIE: Man, Material, Machine, Method, Environment人力,物力,财务,技术,时间(资源) 7M1I: Manpower , Machine , Material , Method, Market , Management , Money , Information人力，机器，材料，方法, 市场，管理，资金，资讯Accuracy 准确度Action 行动Activity 活动Analysis Covariance 协方差分析Analysis of Variance 方差分析Approved 承认Attribute 计数值Average 平均数Balance sheet 资产负债对照表Binomial 二项分配Brainstorming Techniques 脑力风暴法Cause and Effect Matrix 因果图(鱼骨图)CL: Center Line 中心线Check Sheets 检查表Complaint 投诉Conformity 合格（符合）Control 控制Control chart 控制(管制)图Correction 纠正Correlation Methods 相关分析法CPI: continuous Process Improvement 连续工序改善Cross Tabulation Tables 交叉表CS: Customer Service 客（户）服（务）中心DSA: Defects Analysis System 缺陷分析系统Data 数据Deion:品名DCC: Document Control Center 文控中心Decision 决策、判定Defects per unit 单位缺点数Deion 描述Device 装置Do 执行DOE: Design of Experiments 实验设计Element 元素Engineering technology 工程技Environmental 环境Equipment 设备Estimated accumulative frequency 计算估计累计数E Equipment Variation 设备变异External Failure 外部失效,外部缺陷FA: Failure Analysis 失效分析Fact control 事实管理Fatigue 疲劳FMEA: Failure Mode and Effect Analysis失效模式与效果分析FP First-Pass Yield （第一次通过）合格率FQA: Final Quality Assurance 最终品质保证FQC: Final Quality control 最终品质控制Gauge system 测量系统Grade 等级Histogram 直方图Improvement 改善Initial review 先期审查Inspection 检验Internal Failure 内部失效、内部缺陷IPQC: In Process Quality Control 制程品质控制IQC: Incoming Quality Control 来料品质控制IS International Organization for Standardization 国际标准化组织LCL: Lower Control limit 管制下限LQC: Line Quality Control 生产线品质控制LSL: Lower Size Limit 规格下限Machine 机械Manage 管理Materials 物料Measurement 测量Median 中位数MSA: Measurement System Analysis 测量系统分析Occurrence 发生率Operation Instruction 作业指导书Organization 组织Plato 柏拉图PPM arts per Million （百万分之）不良率Plan 计划Policy 方针Population 群体PQA: Process Quality Assurance 制程品质保证Practice 实务(践)Prevention 预防Probability 机率Probability density function 机率密度函数Procedure 流程Process 过程Process capability analysis 制程能力分析（图）Process control and Process capability制程管制与制程能力Product 产品Production 生产Projects 项目QA: Quality Assurance 品质保证QC: Quality Control 品质控制QE: Quality Engineering 品质工程QFD: Quality Function Design 品质机能展开(法)Quality 质量Quality manual 品质手册Quality policy 品质政策(质量方针)Random experiment 随机试验Random numbers 随机数R:Range 全距（极差）Reject 拒收Repair 返修Repeatusility 再现性Reproducibility 再生性Requirement 要求Responsibilities 职责Review 评审Reword 返工Rolled yield 直通率RPN: Risk Priority Number 风险系数Sample 抽样,样本Sample space 样本空间Sampling with replacement 放回抽样Sampling without replacement 不放回抽样Scatter diagram 散布图分析Scrap 报废Simple random sampling 简单随机取样Size 规格SL: Size Line 规格中心线Stratified random sampling 分层随机抽样SOP: Standard Operation Procedure 标准作业书SPC: Statistical Process Control 统计制程管制Specification 规范SQA: Source(Supplier) Quality Assurance 供货商品质保证Stage sampling 分段随机抽样Standard Deviation 标准差Sum of squares 平方和Taguchi-method 田口(试验)方法Theory 原理TQC: Total Quality Control 全面品质控制TQM: Total Quality Management 全面品质管理Traceability 追溯UCL: Upper Control Limit 管制（控制）上限USL: Upper Size Limit 规格上限Validation 确认Variable 计量值Verification 验证Version 版本VOC: Voice of Customer 客户需求VOE: Voice of Engineer 工程需求Inventory stock report:庫存清单报告Sales order report:出货报告（来源：SQE供应商质量）。

QM-—quality management--质量管理qualitymanager 质量经理QE-—quality engineer—-质量工程师QA—-quality assurance-—质量保证QC-—quality control——质量控制IQC—-incoming quality control-—进料检验PQC--process quality control ——制程检验FQC—-finished quality control —-成品检验OQC--outgoing q uality control--出货检验SQE—-supplier quality en g SPC,six g i m a n TS16949,e MSA,FMEA e r--供应商质量工程师QSE——quality system engineer-—质量体系工程师六A西格玛品质论Q坛QD9b-E--assistant quality engineer--质量助理工程师PQE--process quality engineer ——过程质量工程师CS--client server ——客户服务PQC-—pro c{#`8C3e ss quality control-—制程检验,，,，，,，，,improcessFQC——finished quality control ——成品检验，，,,,，,，，final加之VQA--Vendorquality assurance--供应商质量保证parts pe bbs.6sq n r et'n#m i l i o n,简称PPM}就是每百万坏品率少于3 。

全面质量管理(TQM)质量一致性检验inspecton of quality conformity 仲裁性质质量监督quality supervision for arbitration产品保护product protection 产品定型product approval产品分等product classificatin 产品规范product specification产品设计product design 产品质量product quality 产品合格率product percent of pass产品系列化product seriation 产品管理标准product management standard产品计量单位unit of measurement of product 产品售后服务after service产品质量标志product quality mark 产品质量标准product quality standard产品质量管理product quality management 产品质量检验product quality inspection产品质量监督检验product quality supervision and inspection产品质量认证标志certification marking of product quality产品质量认证程序certification procedure of product quality产品质量认证制度certification system of product quality认证certification 立法legislation 自行认证self-certification 认可accreditation 安全认证safety certification安全认证标志mark of safety certification 强制性认证compulsory certificate实验室鉴定laboratory qualification 实验室认证laboratory certification自愿认证制voluntary system of certification 法规机构regulatory authorities认证活动certification activity 认证体系certification system认证计划certification scheme 认证机构certification body检验机构inspecton body许可证licence 申请人applicant 许可证持有者licensee 合格证书certificate of conformity合格标记mark of conformity 认证体系的利用access to certification system认证体系的参预者participant in certification system 认证体系的成员member of certification system批准approval 型式批准type approval测试实验室的认可accreditation of testing laboratory认可accreditation 认可体系accreditation system认可机构accreditation body认可的实验室accredited laboratory认可准则acreditatin criteria 实验室评定laboratory assessment实验室评定者laboratory assessor 认可的实验室的试验报告accredited laboratory test report批准签署人approved signatory 承认和批准协议recognition and approval arrangement承认协议recognition arrangement 单边协议unilateral arrangement双边协议bilateral arrangement 多边协议multilateral arrangemetn互利reciprocity 平等待遇equal treatmetn 国家待遇national treatment国家和平等待遇national and equal treatment 合格及有关的通用概念conformity and related general concept合格conformity 合格测试conformity testing合格acceptable 合格品acceptable part 合格标志mark of conformity合格认证conformity certification 合格认证标志mark of conformity certification合格品标志mark of acceptable product 合格证书certificate of conformity合格证检查inspection by certificate 合格质量检查acceptable quality level评定合格assessment of conformity 合格评定conformity assessment型式评价type evaluation 合格监督conformity surveillance合格证明verification of conformity 合格保证assurance of conformity供货商声明supplier’s declaration 生产许可证production licence一致consensus 检验inspection 不定期检验nonperiodic inspection抽样检验sampling inspection 出厂检验exfactory inspection第一方检验first party inspection 第二方检验second party inspection第三方检验third party inspection 第三方认证制度third pary certification定期检验periodic inspection 交收检验acceptance inspeciton例行检验routine inspeciton 生产检验produciton inspeciton生产定型检验production approval inspeciton 验收检验acceptance inspeciton验证检验compliance test 仲裁检验arbitration inspection创造商担保guarantee by manufacturer 百分比抽样检查percent sampling inspection不合格判定数rejection number 不合格质量水平rejecton quality level抽查型质量监督sampling quality supervision 环境监测environmental monitoring抽样sampling 多次抽样multiple sampling 分层抽样stratified sampling分层随机抽样stratified random smapling 多级抽样multistage sampling二次抽样double sampling 试件test piece 试验报告test report试样test sample 测试设备testing equipment 测试试验室testing laboratority商标trademark 商品名称trade-name 测试testing 试验test 实验室间的试验比较interlaboratorytest comparisons熟练水平试验proficiency testing 次品defective product代用产品substitute product 定量试验quantitative test 出口管理export control出口许可证制度export control 进口许可证制度import licence system定额管理quota management 非关税壁垒non-tarrif barrier 关税壁垒tariff barrier关税普遍优惠制general preferential dutiesCore value (核心价值) Love 愛心Confidence 信心Decision 決心Corporate culture (公司文化)Integration 融合Responsibility 責任Progress 進步3T STRATEGYTime to market 及時切入生產Time to volume 及時大量生產Time to money 及時大量交貨FOUR CONTROL SYSTEM 四大管制系統Engineering control system 工程管制系統Quality control system 品質管制系統Manufacturing control system 生產管制系統Management control system 經營管制系統7SClassification 整理(sorting, organization) -seiriRegulation 整頓(arrangement, tidiness)-seitonCleanliness 清掃(sweeping, purity)—seisoConservation 清洁(cleaning, cleanliness)—seiktsuCulture 教養(discipline)-shitsukeSave 節約Safety 安全二：英文縮寫品質人員名稱類QC quality control 品質管理人員FQC final quality control 終點品質管制人員IPQC in process quality control 制程中的品質管制人員OQC output quality control 最終出貨品質管制人員IQC incoming quality control 進料品質管制人員TQC total quality control 全面質量管理POC passage quality control 段檢人員QA quality assurance 質量保證人員OQA output quality assurance 出貨質量保證人員QE quality engineering 品質工程人員品質保證類FAI first article inspection 新品首件檢查FAA first article assurance 首件確認CP capability index 能力指數CPK capability process index 模具製程能力參數SSQA standardized supplier quality audit 合格供應商品質評估FMEA failure model effectiveness analysis 失效模式分析FQC 運作類AQL Acceptable Quality Level 運作類允收品質水準S/S Sample size 抽樣檢驗樣本大小ACC Accept 允收REE Reject 拒收CR Critical 極嚴重的MAJ Major 主要的MIN Minor 輕微的Q/R/S Quality/Reliability/Service 品質/可靠度/服務P/N Part Number 料號L/N Lot Number 批號AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件檢查報告PPM Percent Per Million 百萬分之一制程統計品管專類SPC Statistical Process Control 統計製程管制SQC Statistical Quality Control 統計品質管制GRR Gauge Reproductiveness ＆Repeatability 量具之再制性及重測性判斷量可靠與否DIM Dimension 尺寸DIA Diameter 直徑N Number 樣品數其它品質術語類QIT Quality Improvement Team 品質改善小組ZD Zero Defect 零缺點QI Quality Improvement 品質改善QP Quality Policy 目標方針TQM Total Quality Management 全面品質管理RMA Return Material Audit 退料認可7QCTools 7 Quality Control Tools ECN Engineering Change Notice ECO Engineering Change Order 序改動通知PMP Product Management Plan品管七大手法通用之件類工程變更通知(供應商)工程改動要求(客戶) PCN生產管制計劃Process Change Notice 工SIP SOP 驗規範BOM SPEC Standard Inspection ProcedureStandard Operation ProcedureBill Of Material 物料清單PS Package Specification 包裝規範Specification 規格DWG Drawing 圖面系統文件類製程檢驗標準程序製造作業規範IS Inspection Specification 成品檢ES Engineering Standard 工程標準CGOO China General PCE 龍華廠文件IWS International Workman Standard 工藝標準ISO International Standard Organization 國際標準化組織GS General Specification 普通規格部類PMC Production & Material Control 生產和物料控制PCC Product control center 生產管制中心PPC Production Plan Control 生產計劃控制MC Material Control 物料控制DC Document Center 資料中心QE Quality Engineering 品質工程(部)QA Quality Assurance 品質保證(處)QC Quality Control 品質管制(課)PD Product Department 生產部LAB Laboratory 實驗室IE Industrial Engineering 工業工程R&D Research ＆Design 設計開發部生產類PCs Pieces 個(根，塊等)PRS Pairs 雙(對等)CTN Carton 卡通箱PAL Pallet/skid 棧板PO Purchasing Order 采購訂單MO Manufacture Order 生產單D/C Date Code 生產日期碼ID/C Identification Code (供應商)識別碼SWR Special Work Request 特殊工作需求L/N Lot Number 批號P/N Part Number 料號OEM Original Equipment Manufacture 原設備製造PC Personal Computer 個人電腦CPU Central Processing Unit 中央處理器A 。

序号英文缩写中文名称英文全称1 SPC 统计制程管制 Statistical Process Control2 USL 规格上限 Upper Specification Limit3 LSL 规格下限 Lower Specification Limit4 UCL 管制上限 Upper control limit5 LCL 管制下限 Lower control limit6 PCL 前置管制中心限 Per-control Central Limit7 UPCL 前置管制上限 Upper Per-control Limit8 LPCL 前置管制下限 Lower Per-control Limit9 Ca10 Cp 潜在过程能力指数 Capability11 Pp12 Ppk13 CIP 持续改进过程模式 Continuous Improvement Process Model14 ANOVA 变异数分析 Analysis of Variance15 BSC 平衡计分卡 Balanced Scoredoard16 信赖区间 Confidence interval17 管制图 Control chart18 CTQ 品质关键 Critical to quality19 DPMO 每百万个机会的缺点数 Defects per million opportunities20 DPM 每百万单位的缺点数 Defects per million21 DPU 单位缺点数 Defects per unit22 DFSS 六个希格玛设计 Design for six sigma23 DOE 实验设计 Design of experiment24 制造设计 Design of manufactring25 FMEA 故障型态与效应分析 Failure mode and effect analysis26 故障率 Failure rate27 Gage R&R 量规重复能力与重制能力 Gage repeatability & reproducibility28 直方图 Histogram29 假设检定 Hypothesis testing30 KM 知识管理 Knowledge Management31 MRP 物料需求规划 Material require planning32 常态分配 Normal distribution33 QFD 品质机能展开 Quality function deployment34 6σ六个希格玛 Six Sigma35 σ, s 标准差 Standard deviation36 σ2, S2 变异数 Variance37 ABC 作业制成本制度 Activity-Based Costing38 BTF 计划生产 Build To Forecast39 BTO 订单生产 Build To Order40 CPM 要径法 Critical Path Method41 CPM 每一百万个使用者会有几次抱怨 Complaint per Million42 CRM 客户关系管理 Customer Relationship Management43 CRP 产能需求规划 Capacity Requirements Planning44 CS 顾客满意度 Customer Satisfaction45 CTO 客制化生产 Configuration To Order46 DVT 设计验证 Design Verification Testing47 DSS 决策支持系统 Decision Support System48 EC 设计变更／工程变更 Engineer Change49 EC 电子商务 Electronic Commerce50 EMC 电磁相容 Electric Magnetic Capability51 EOQ 基本经济订购量 Economic Order Quantity52 ERP 企业资源规划 Enterprise Resource Planning53 FMS 弹性制造系统 Flexible Manufacture System54 FQC 成品质量管理 Finish or Final Quality Control55 IPQC 制程质量管理 In-Process Quality Control56 IQC 进料质量管理 Incoming Quality Control57 ISO 国际标准组织 International Organization for Standardization58 ISAR 首批样品认可 Initial Sample Approval Request59 JIT 实时管理 Just In Time60 MES 制造执行系统 Manufacturing Execution System61 MO 制令 Manufacture Order62 MPS 主生产排程 Master Production Schedule63 MRO 请修(购)单 Maintenance Repair Operation64 MRP 物料需求规划 Material Requirement Planning65 MRPII 制造资源计划 Manufacturing Resource Planning66 NFCF 更改预估量的通知 Notice for Changing Forecast67 OEM 委托代工 Original Equipment Manufacture68 ODM 委托设计与制造 Original Design & Manufacture69 OPT 最佳生产技术 Optimized Production Technology70 OQC 出货质量管理 Out-going Quality Control71 PDCA PDCA管理循环 Plan-Do-Check-Action72 PO 订单 Purchase Order73 QA 品质保证 Quality Assurance74 QC 质量管理 Quality Control75 QCC 品管圈 Quality Control Circle76 QE 品质工程 Quality Engineering77 RMA 退货验收 Returned Material Approval78 ROP 再订购点 Re-Order Point79 SCM 供应链管理 Supply Chain Management80 SFC 现场控制 Shop Floor Control81 SO 订单 Sales Order82 SOR 特殊订单需求 Special Order Request83 TOC 限制理论 Theory of Constraints84 TPM 全面生产管理 Total Production Management85 TQC 全面质量管理 Total Quality Control86 TQM 全面品质管理 Total Quality Management87 WIP 在制品 Work In Process。

一.常用英文缩写QC: Quality Control 品质管控QA: Quality Assurance 质量保证IQC: Incoming Quality Control 进料质量管理IPQC: In-Process Quality Control 制程质量管理FQC: Final Quality Control 最终质量管理OQC: Outgoing Quality Control 出货质量管理QCC: Quality Control Circle 品管圈QE: Quality Engineering 质量工程PDCA管理循环(Plan-Do-Check-Action)SPC : Statistic Process Control 统计制程管制TQM: Total Quality management 全面质量管理WIP: Work In Process 在制品MO: Manufacture Order 制令JIT: Just In Time 实时管理ISO: International Organization For Standardization 国际标准化组织BOM: Bill Of Material 物料清单5S : 整理,整顿,清扫,清洁,素养FIFO: FIRST IN FIRST OUT 先进先出管理CLCA: Closed Loop Corrective Action5C: Characterize the problemContain the problemCausal analysisCorrective actionsClosure checklistORT: Out-going Reliability Test,出货可靠度测试.TR(Test Run)试产: 与其对应ASUS 端会进行DVT (Design Validation TestFTR(Final Test Run)最终试产: 与其对应ASUS 端会进行PVT(Product Validation Test) MP(Mass Production)量产: 与其对应ASUS 端会进行PVT (Mass Validation T est Ramp Up:产能提升.F.A.I(First Article Inspection): 首件检查.Cpk: 制程能力指标,Cpk不小于1.33表示制程质量稳定良好,否则需进行改善.OBA(Out Box Audit): 出货开箱检查.SIP SOPNPRR: New Product Readiness Review (新产品导入准备)5M：人(Man)、机(Machine)、料(Material)、法(Method)、基准(Measurement) QSA: Quality System Assess 质量系统评鉴规范QPA: Quality Process Assess 制程能力评鉴规范评鉴前会议(Open Meeting)评鉴小组内部讨论会议(Inner meeting)评鉴总结会议(Close meeting)合格(Approved) 有条件合格(Conditionally Approved) 不合格(Rejected)生产良率(Yield Rate)件内变异(within-piece variation)件间变异(piece-to-piece variation)时间与时间的变异(time-to-time variation)管制(Control) 制程(Process)5W1H(Why,Who,When,What,Where,How)Quality Management Plan – QMPFunctional Process Manual (FPM)Program Product Features Guide (PFG)PPAP (Piece Part Approval Process)AQP-(Advanced Quality Planning)Total Process Defects (TPD)PMT (Process Management Tool)PCR：Process Change Request 制程变更需求。

英语日常用语——质量管理QUALITY CONTROL1 Total Quality Control(TQC)is a better quality control system.全面质量管理(简称TQC)是一种较好的质量管理体系。

2 TQC over the project will be strengthened.对于这个工程的全面质量管理将要加强。

3 To maintain the best quality of the construction work is the important responsibility of the field controllers.保持施工工作的优良质量是现场管理人员的重要职责。

4 We possess skilled technician and complete measuring and test instruments used to ensure the quality of engineering .我们拥有熟练的技术力量和齐全的检测手段,可以确保工程质量。

5 Field inspection work is handled (executed, directed )by our Inspection Section.现场检查工作由我们的检查科管理(实施、指导)。

6 Our site quality inspector will report to the Project Manager everyday. 我们的现场质量检查员将每天向工程项目经理汇报。

7 I want to see the certificate of quality (certificate of manufacturer, certificate of inspection, certificate of shipment, material certificate, certificate of proof).我要看看质量证书(制造厂证书、检查证明书、出口许可证书、材料合格证、检验证书)。

质量管理相关的词汇一、质量（quality）1. 发音：英[ˈkwɒləti]；美[ˈkwɑːləti]2. 词性：名词。

3. 释义：产品或服务的优劣程度。

例如：The quality of this product is very high.（这个产品的质量非常高。

）二、管理（management）1. 发音：英[ˈmænɪdʒmənt]；美[ˈmænɪdʒmənt]2. 词性：名词。

3. 释义：组织、协调、控制等一系列活动的过程。

例如：Good management can improve the efficiency of the company.（良好的管理能提高公司的效率。

）三、标准（standard）1. 发音：英[ˈstændəd]；美[ˈstændərd]2. 词性：名词。

3. 释义：衡量事物的准则。

例如：We should follow the international standards in quality management.（在质量管理中我们应该遵循国际标准。

）四、检验（inspection）1. 发音：英[ɪnˈspekʃn]；美[ɪnˈspekʃn]2. 词性：名词。

3. 释义：检查、查看是否符合要求。

例如：The inspection of products is a very important part of quality management.（产品检验是质量管理非常重要的一部分。

）五、控制（control）1. 发音：英[kənˈtrəʊl]；美[kənˈtroʊl]2. 词性：名词或动词。

3. 释义：作为名词时，指控制的手段或能力；作为动词时，指掌握住不使任意活动或越出范围。

例如：Quality control is essential for a successful business.（质量控制对一个成功的企业来说是必不可少的。

500个质量管理专用中英文术语集锦-标准化文件发布号：（9556-EUATWK-MWUB-WUNN-INNUL-DDQTY-KII500个质量管理专用中英文术语集锦质量必背——职业篇1.PDCA：Plan、Do、Check、Action 策划、实施、检查、处置2.PPAP：Production Part Approval Process生产件批准程序3.APQP：Advanced Product Quality Planning产品质量先期策划4.FMEA：Potential Failure Mode and Effects Analysis 潜在失效模式及后果分析5.SPC：Statistical Process Control统计过程控制6.MSA：Measurement System Analysis 测量系统控制7.CP：Control Plan 控制计划8.QSA：Quality System Assessment 质量体系评定9.PPM：Parts Per Million 每百万零件不合格数10.QM：Quality Mauna质量手册11.QP：Quality Procedure质量程序文件/Quality Planning质量策划/QualityPlan 质量计划12.CMK：机器能力指数13.CPK：过程能力指数14.CAD：Computer-Aided Design 计算机辅助能力设计15.OEE：Overall Equipment Effectiveness 设备总效率16.QFD：Quality Function Deployment质量功能展开17.FIFO：First in, First out先进先出18.COPS：Customer Oriented Processes顾客导向过程19.TCQ：Time、Cost、Quality时间、成本、质量20.MPS：Management Processes管理性过程21.SPS：Support Processes支持性过程22.TQM：Total Quality Management全面质量管理23.PQA：Product Quality Assurance产品质量保证（免检）24.QP-QC-QI：质量三步曲，质量计划－质量控制－质量改进25.QAF：Quality Assurance File质量保证文件26.QAP：Quality Assurance Plan质量保证计划27.PFC：Process Flow Chart过程流程图28.QMS：Quality Management Systems质量管理体系29.JIT：Just In Time准时（交货）30.ERP：Enterprise Requirement Planning企业需求计划31.QC：Quality Control 质量控制32.QA：Quality Audit 质量审核/Qality Assurance 质量保证33.IQC：In Come Quality Control 进货质量控制34.IPQC：In Process Quality Control 过程质量控制35.FQC：Final Quality Control 成品质量控制36.OQC：Out Quality Control 出货质量控制37.4M1E：Man、Machine、Material、Method、Environment人、机、料、法、环38.5W1H：Why、What、Who、When、Where、How 为何/做什么/谁做/时间/地点/如何做39.6S：Seiri、Seiton、Seiso、Seiketsu、Shitsuke、Safety 整理、整顿、清扫、清洁、素养、安全40.TRI值：Total Record Injury（三种）可记录工伤值41.SMART：精明原则，Specific Measurable Achievable Result OrientedTimed（具体的描述、可以测量的、可以通过努力实现的、有结果导向性的、有时间性的）质量必背——企业篇1.5S：5S管理2.ABC：作业制成本制度（Activity-Based Costing）3.ABB：实施作业制预算制度（Activity-Based Budgeting）4.ABM：作业制成本管理（Activity-Base Management）5.APS：先进规划与排程系统（Advanced Planning and Scheduling）6.ASP：应用程序服务供货商（Application Service Provider）7.ATP：可承诺量（Available To Promise）8.AVL：认可的供货商清单（Approved Vendor List）9.BOM：物料清单（Bill Of Material）10.BPR：企业流程再造（Business Process Reengineering）11.BSC：平衡记分卡（Balanced ScoreCard）12.BTF：计划生产（Build To Forecast）13.BTO：订单生产（Build To Order）14.CPM：要径法（Critical Path Method）15.CPM：每一百万个使用者会有几次抱怨（Complaint per Million）16.CRM：客户关系管理（Customer Relationship Management）17.CRP：产能需求规划（Capacity Requirements Planning）18.CTO：客制化生产（Configuration To Order）19.DBR：限制驱导式排程法（Drum-Buffer-Rope）20.DMT：成熟度验证（Design Maturing Testing）21.DVT：设计验证（Design Verification Testing）22.DRP：运销资源计划（Distribution Resource Planning）23.DSS：决策支持系统（Decision Support System）24.EC：设计变更/工程变更（Engineer Change）25.EC：电子商务（Electronic Commerce）26.ECRN：原件规格更改通知（Engineer Change Request Notice）27.EDI：电子数据交换（Electronic Data Interchange）28.EIS：主管决策系统（Executive Information System）29.EMC：电磁相容（Electric Magnetic Capability）30.EOQ：基本经济订购量（Economic Order Quantity）31.ERP：企业资源规划（Enterprise Resource Planning）32.FAE：应用工程师（Field Application Engineer）33.FCST：预估（Forecast）34.FMS：弹性制造系统（Flexible Manufacture System）35.FQC：成品质量管理（Finish or Final Quality Control）36.IPQC: 制程质量管理（In-Process Quality Control）37.IQC：进料质量管理（Incoming Quality Control）38.ISO：国际标准组织（International Organization for Standardization）39.ISAR：首批样品认可（Initial Sample Approval Request）40.JIT：实时管理（Just In Time）41.KM：知识管理（Knowledge Management）42.L4L：逐批订购法（Lot-for-Lot）43.LTC：最小总成本法（Least Total Cost）44.LUC：最小单位成本（Least Unit Cost）45.MES：制造执行系统（Manufacturing Execution System）46.MO：制令（Manufacture Order）47.MPS：主生产排程（Master Production Schedule）48.MRO：请修（购）单（Maintenance Repair Operation）49.MRP：物料需求规划（Material Requirement Planning）50.MRPII：制造资源计划（Manufacturing Resource Planning）51.NFCF：更改预估量的通知Notice for Changing Forecast52.OEM：委托代工（Original Equipment Manufacture）53.ODM：委托设计与制造（Original Design & Manufacture）54.OLAP：在线分析处理（On-Line Analytical Processing）55.OLTP：在线交易处理（On-Line Transaction Processing）56.OPT：最佳生产技术（Optimized Production Technology）57.OQC：出货质量管理（Out-going Quality Control）58.PDCA：PDCA管理循环（Plan-Do-Check-Action）59.PDM：产品数据管理系统（Product Data Management）60.PERT：计划评核术（Program Evaluation and Review Technique）61.PO：订单（Purchase Order）62.POH：预估在手量（Product on Hand）63.PR：采购申请（Purchase Request）64.QA：品质保证（Quality Assurance）65.QC：质量管理（Quality Control）66.QCC：品管圈（Quality Control Circle）67.QE：品质工程（Quality Engineering）68.RCCP：粗略产能规划（Rough Cut Capacity Planning）69.RMA：退货验收（Returned Material Approval）70.ROP：再订购点（Re-Order Point）71.SCM：供应链管理（Supply Chain Management）72.SFC：现场控制（Shop Floor Control）73.SIS：策略信息系统（Strategic Information System）74.SO：订单（Sales Order）75.SOR：特殊订单需求（Special Order Request）76.SPC：统计制程管制（Statistic Process Control）77.TOC：限制理论（Theory of Constraints）78.TPM：全面生产管理（Total Production Management）79.TQC：全面质量管理（Total Quality Control）80.TQM：全面品质管理（Total Quality Management）81.WIP：在制品（Work In Process）质量必背——部门篇QS: Quality system品质系统CS: Customer Service 客户服务QC: Quality control品质管理IQC: Incoming quality control 进料检验LQC: Line Quality Control 生产线品质控制IPQC: In process quality control 制程检验FQC: Final quality control 最终检验OQC: Outgoing quality control 出货检验QA: Quality assurance 品质保证SQA: Source(supplier) Quality Assurance 供应商品质保证(VQA) CQA：Customer Quality Assurance客户质量保证PQA rocess Quality Assurance 制程品质保证QE: Quality engineer 品质工程CE: component engineering零件工程EE: equipment engineering设备工程ME: manufacturing engineering制造工程TE: testing engineering测试工程PPE product Engineer 产品工程IE: Industrial engineer 工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC: producing control生管MC: mater control物管GAD: General Affairs Dept.总务部A/D: Accountant /Finance Dept.会计LAB: Laboratory实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department生产部PA:采购(PUR: Purchasing Dept.)SMT: Surface mount technology 表面粘着技术MFG: Manufacturing 制造MIS: Management information system 资迅管理系统DCC: document control center 文件管制中心质量必背——场内作业QT: Quality target品质目标QP: Quality policy目标方针QI: Quality improvement品质改善CRITICAL DEFECT:严重缺点（CR）MAJOR DEFECT:主要缺点（MA）MINOR DEFECT:次要缺点（MI）MAX: Maximum最大值MIN: Minimum最小值DIA diameter直径DIM dimension尺寸LCL: Lower control limit管制下限UCL: Upper control limit管制上限EMI:电磁干扰ESD:静电防护EPA:静电保护区域ECN:工程变更ECO: Engineering change order工程改动要求（客户）ECR:工程变更需求单CPI: Continuous Process Improvement 连续工序改善Compatibility：兼容性Marking：标记DWG drawing图面Standardization：标准化Consensus：一致Code：代码ZD: Zero defect零缺点Tolerance：公差Subject matter：主要事项Auditor：审核员BOM: Bill of material物料清单Rework：重工ID：identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR：First Piece Inspection Report首件检查报告FAA:首件确认SPC：统计制程管制CP: capability index（准确度）CPK: capability index of process(制程能力) PMP:制程管理计划（生产管制计划）MPI:制程分析DAS effects Analysis System 缺陷分析系统PPB：十亿分之一Flux：助焊剂P/N:料号L/N：Lot Number批号Version：版本Quantity：数量Valid date：有效日期MIL-STD：Military-Standard军用标准ICT: In Circuit Test (线路测试)ATE：Automatic Test Equipment自动测试设备MO: Manufacture Order生产单T/U: Touch Up (锡面修补)I/N:手插件P/T:初测F/T: Function Test (功能测试-终测)AS 组立P/K:包装TQM: Total quality control全面品质管理MDA: Manufacturing defect analysis制程不良分析(ICT) RUN-IN:老化实验HI-pot：高压测试FMI：Frequency Modulation Inspect高频测试DPPM: Defect Part Per Million(不良率的一种表达方式：百万分之一) 1000PPM即为0.1% Corrective Action: (CAR改善对策)ACC：允收REJ:拒收S/S：Sample size抽样检验样本大小SI-SIV：Special I-Special IV特殊抽样水平等级CON：Concession / Waive特采ISO:国际标准化组织ISA：Industry Standard Architecture工业标准体制结构OBA:开箱稽核FIFO:先进先出PDCA:管理循环Plan do check action计划，执行，检查，总结WIP:在制品（半成品）S/O: Sales Order (业务订单)P/O: Purchase Order (采购订单)P/R: Purchase Request (请购单)AQL: acceptable quality level允收品质水准LQL; Limiting quality level最低品质水准QVL: qualified vendor list合格供应商名册AVL ：认可的供货商清单(Approved Vendor List) QCD: Quality cost delivery（品质，交期，成本）MPM: Manufacturing project management制造专案管理KPI: Key performance indicate重要绩效指标MVT: Manufacturing Verification Test制造验证试产Q/R/S：Quality/Reliability/Service质量/可靠度/服务STL: ship to line（料到上线）NTF: No trouble found误判CIP: capacity improvement plan（产能改善计划）MRB: material review board（物料审核小组）MRB: Material reject bill退货单JIT: just in time（即时管理）5S:seiri seiton seiso seiketsu shitsuke（整理，整顿，清扫，清洁，修养）SOP: standard operation process（标准作业程序）SIP: Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction（作业指导书）SMD: surface mounting device（表面粘着原件）FAR: failure analysis report故障分析报告CAR: Corrective action report改善报告BPR：企业流程再造 (Business Process Reengineering)ISAR ：首批样品认可(Initial Sample Approval Request)-JIT：实时管理 (Just In Time)QCC ：品管圈 (Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面品质环境管理) PD: Production Department (制造)LOG: Logistics (后勤支持)Shipping: (进出口)AOQ：Average Output Quality平均出货质量AOQL：Average Output Quality Level平均出货质量水平FMEA：failure model effectiveness analysis失效模式分析CRB: Change Review Board (工程变更会议)CSA：Customer Simulate Analysis客户模拟分析SQMS：Supplier Quality Management System供应商品质管理系统QIT: Quality Improvement Team 品质改善小组QIP：Quality Improvement Plan品质改善计划CIP：Continual Improvement Plan持续改善计划M.Q.F.S: Material Quality Feedback Sheet (来料品质回馈单) SCAR: Supplier Corrective Action Report (供货商改善对策报告)8D Sheet: 8 Disciplines sheet ( 8D单)PDCA：PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知)QAPS: Quality Assurance Process Sheet (品质工程表)DRP ：运销资源计划 (Distribution Resource Planning)DSS：决策支持系统 (Decision Support System)EC ：电子商务 (Electronic Commerce)EDI ：电子资料交换 (Electronic Data Interchange)EIS ：主管决策系统 (Executive Information System)ＥＲＰ：企业资源规划 (Enterprise Resource Planning)FMS ：弹性制造系统 (Flexible Manufacture System)KM ：知识管理 (Knowledge Management)4L ：逐批订购法 (Lot-for-Lot)LTC ：最小总成本法 (Least Total Cost)LUC ：最小单位成本 (Least Unit Cost)MES ：制造执行系统 (Manufacturing Execution System) MPS ：主生产排程 (Master Production Schedule)MRP ：物料需求规划 (Material Requirement Planning) MRPⅡ：制造资源计划 (Manufacturing Resource Planning) OEM ：委托代工 (Original Equipment Manufacture)ODM ：委托设计与制造 (Original Design & Manufacture) OLAP：线上分析处理 (On-Line Analytical Processing) OLTP：线上交易处理 (On-Line Transaction Processing) OPT ：最佳生产技术 (Optimized Production Technology) PDCA：PDCA管理循环 (Plan-Do-Check-Action)PDM：产品数据管理系统 (Product Data Management)) RCCP：粗略产能规划 (Rough Cut Capacity Planning) SCM ：供应链管理 (Supply Chain Management)SFC ：现场控制 (Shop Floor Control)TOC：限制理论 (Theory of Constraints)TQC ：全面品质管制 (Total Quality Control)FYI/R: For your information/reference仅供参考ASAP:尽快S/T: Standard time标准时间TPM: total production maintenance：全面生产保养ESD Wrist strap：静电环IT: information technology信息技术，资讯科学CEO：Chief Executive Officer执行总裁COO：Chief Operating Officer首席业务总裁SWOT：Strength, Weakness, Opportunity, Threat优势﹐弱点﹐机会﹐威胁Competence：专业能力Communication：有效沟通Cooperation：统御融合Vibration Testing：振动测试IDP：Individual Development Plan个人发展计划MRP：Material Requirement Planning物料需求计划MAT'S：Material材料LRR：Lot Reject Rate批退率ATIN：Attention知会3C：Computer ,Communication , Consumer electronic消费性电子5W1H：When , Where , Who , What , Why , Ho5M: Man , Machine , Material , Method , Measurement人,机器,材料,方法,测量4MIE: Man, Material, Machine, Method, Environment人力,物力,财务,技术,时间(资源)7M1I: Manpower , Machine , Material , Method, Market , Management , Money , Information人力，机器，材料，方法, 市场，管理，资金，资讯Accuracy 准确度Action 行动Activity 活动Analysis Covariance 协方差分析Analysis of Variance 方差分析Approved 承认Attribute 计数值Average 平均数Balance sheet 资产负债对照表Binomial 二项分配Brainstorming Techniques 脑力风暴法Cause and Effect Matrix 因果图(鱼骨图)CL: Center Line 中心线Check Sheets 检查表Complaint 投诉Conformity 合格（符合）Control 控制Control chart 控制(管制)图Correction 纠正Correlation Methods 相关分析法CPI: continuous Process Improvement 连续工序改善Cross Tabulation Tables 交叉表CS: Customer Service 客（户）服（务）中心DSA: Defects Analysis System 缺陷分析系统Data 数据 Deion:品名DCC: Document Control Center 文控中心Decision 决策、判定Defects per unit 单位缺点数Deion 描述Device 装置Do 执行DOE: Design of Experiments 实验设计Element 元素Engineering technology 工程技Environmental 环境Equipment 设备Estimated accumulative frequency 计算估计累计数E Equipment Variation 设备变异External Failure 外部失效,外部缺陷FA: Failure Analysis 失效分析Fact control 事实管理Fatigue 疲劳FMEA: Failure Mode and Effect Analysis失效模式与效果分析FP First-Pass Yield （第一次通过）合格率FQA: Final Quality Assurance 最终品质保证FQC: Final Quality control 最终品质控制Gauge system 测量系统Grade 等级Histogram 直方图Improvement 改善Initial review 先期审查Inspection 检验Internal Failure 内部失效、内部缺陷IPQC: In Process Quality Control 制程品质控制IQC: Incoming Quality Control 来料品质控制IS International Organization for Standardization 国际标准化组织LCL: Lower Control limit 管制下限LQC: Line Quality Control 生产线品质控制LSL: Lower Size Limit 规格下限Machine 机械Manage 管理Materials 物料Measurement 测量Median 中位数MSA: Measurement System Analysis 测量系统分析Occurrence 发生率Operation Instruction 作业指导书Organization 组织Plato 柏拉图PPM arts per Million （百万分之）不良率Plan 计划Policy 方针Population 群体PQA: Process Quality Assurance 制程品质保证Practice 实务(践)Prevention 预防Probability 机率Probability density function 机率密度函数Procedure 流程Process 过程Process capability analysis 制程能力分析（图）Process control and Process capability制程管制与制程能力Product 产品Production 生产Projects 项目QA: Quality Assurance 品质保证QC: Quality Control 品质控制QE: Quality Engineering 品质工程QFD: Quality Function Design 品质机能展开(法) Quality 质量Quality manual 品质手册Quality policy 品质政策(质量方针)Random experiment 随机试验Random numbers 随机数R:Range 全距（极差）Reject 拒收Repair 返修Repeatusility 再现性Reproducibility 再生性Requirement 要求Responsibilities 职责Review 评审Reword 返工Rolled yield 直通率RPN: Risk Priority Number 风险系数Sample 抽样,样本Sample space 样本空间Sampling with replacement 放回抽样Sampling without replacement 不放回抽样Scatter diagram 散布图分析Scrap 报废Simple random sampling 简单随机取样Size 规格SL: Size Line 规格中心线Stratified random sampling 分层随机抽样SOP: Standard Operation Procedure 标准作业书SPC: Statistical Process Control 统计制程管制Specification 规范SQA: Source(Supplier) Quality Assurance 供货商品质保证Stage sampling 分段随机抽样Standard Deviation 标准差Sum of squares 平方和Taguchi-method 田口(试验)方法Theory 原理TQC: Total Quality Control 全面品质控制TQM: Total Quality Management 全面品质管理Traceability 追溯UCL: Upper Control Limit 管制（控制）上限USL: Upper Size Limit 规格上限Validation 确认Variable 计量值Verification 验证Version 版本VOC: Voice of Customer 客户需求VOE: Voice of Engineer 工程需求Inventory stock report:庫存清单报告Sales order report:出货报告（来源：SQE供应商质量）。