HT185WX1-100 (2-CCFL)

  • 格式:pdf
  • 大小:1.40 MB
  • 文档页数:28

PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF BOE OT AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE OT AND MUST BE RETURNED TO BOE OT UPON ITS REQUESTTITLE : HT185WX1-100 Product Specification Rev.0BEIJING BOE OPTOELECTRONICS TECHNOLOGYSPEC. NUMBER S864-5040PRODUCT GROUP TFT-LCDRev.0ISSUE DATE 2008.12. 24.PAGE 1 OF 28 A4(210 X 297)B2006-5006-O (1/3)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’REVISION HISTORYREV. 0 ECN No. DESCRIPTION OF CHANGES Initial Release DATE Dec.24.08’ PREPARED Qiu HaiJunSPEC. NUMBER S864-5040SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 2 OF 28 A4(210 X 297)B2006-5006-O (2/3)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’ContentsNo. 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 General Description Absolute Maximum Ratings Electrical Specifications Optical Specifications Interface Connection Signal Timing Specifications Signal Timing Waveforms of Interface Signal Input Signals, Display Colors & Gray Scale of Colors Power Sequence Mechanical Characteristics Reliability Test Handling& Cautions Product Serial Number Packing Appendix Item Page 4 6 7 8 10 13 15 17 18 19 20 21 22 23 25SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 3 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’1.0 GENERAL DESCRIPTION1.1 Introduction HT185WX1-100 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 18.5 inch diagonally measured active area with WXGA resolutions (1366 horizontal by 768 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type.CN21LVDS Input SignalConnector (CN 1 )LVDS Rx + T/CON + Mini LVDS TxSource DriverGate DriverVDDDC/DC Gamma VcomTFT LCD Panel 1366 × 768CN221.2 Features LVDS Interface with 1 pixel / clock High-speed response Low power consumption 6-bit (Hi-FRC) color depth, display 16. 7M colors Incorporated edge type back-light (Two lamps) High luminance and contrast ratio, low reflection and wide viewing angle DE (Data Enable) only RoHS /TCO’ 03 CompliantSPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 4 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCT 1.3 Application Desktop Type of PC & Workstation Use Slim-Size Display for Stand-alone Monitor Display Terminals for Control System Monitors for Process ControllerREV 0ISSUE DATE Dec. 24. 08’1.4 General Specification The followings are general specifications at the model HT185WX1-100. <Table 1. General Specifications> Parameter Active area Number of pixels Pixel pitch Pixel arrangement Display colors Display mode Dimensional outline Weight Surface Treatment Back-light Specification 409.8(H) × 230.4(V) 1366(H) ×768(V) 0.3(H) ×0.3(V) RGB Vertical stripe 16.7M Normally White 430.4(H) × 254.6(V) × 16.5(D) typ. 2000 (max.) Haze 25%, 3H Top/Bottom edge side, 2-CCFL type mm g colors Unit mm pixels mmRemarksSPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 5 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’2.0 ABSOLUTE MAXIMUM RATINGSThe followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. Absolute Maximum Ratings>Symbol Parameter Power Supply Voltage Logic Supply Voltage Back-light Lamp Current Back-light Lamp frequency Operating Temperature Storage Temperature VDD VIN IBL FL TOP TST -0.3 VSS-0.3 3 40 0 -20 5.0 VDD+0.3 8.0 80 +50 +60 V V mA kHz ℃ ℃ 1) 1) Ta = 25 ℃ Min. Max. Unit [VSS=GND=0V] RemarksNote : 1) Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 OC max. and no condensation of water.100 90 80(39,90)Relative Humidity (%RH)60O p e ra tin g R a n g e40(50,50)(60,30)20S to ra g e R a n g e5 -2 0 0 20 40 60 80T e m p e ra tu re (˚ ) CSPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 6 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’3.0 ELECTRICAL SPECIFICATIONS3.1Electrical Specifications< Table 3. Electrical specifications >ParameterPower Supply Voltage Power Supply Current In-Rush Current Permissible Input Ripple Voltage High Level Differential Input Threshold Voltage Low Level Differential Input Threshold Voltage Differential input voltage Differential input common mode voltage Back-light Lamp Voltage Back-light Lamp Current Back-light Lamp operating Frequency Lamp Start Voltage Lamp Life PD Power Consumption PBL Ptotal 50,000 3 10.68 13.68 1800 5 14.0 19 VDD IDD IRUSH VRF VIH VIL |VID | Vcm VBL IBL FL[Ta =25±2 ℃] Max.5.5 1000 3.0 100 +100 600 1.5 880 8.0 80 1400 Vrms mArms KHz Vrms Vrms Hrs W W W IBL=7.5 mA, Note 5 Note 3 25℃, Note 4 0℃, Note 4 IBL= 7.5 mAMin.4.5 -100 200 1.0 3.0 40 -Typ.5.0 600 2.0 1.2 730 7.5 -UnitVRemarksNote1mA A mV mV mV mV VIH=100mV, VIL=-100mV Note 2 VDD = 5.0VNotes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VDD=5.0V, Frame rate=75Hz and Clock frequency = 95MHz. Test Pattern of power supply current a) Typ : Color Bar pattern b) Max : Skip Sub Pixel Pattern2. Duration of rush current is about 2 ms and rising time of VDD is 520 μs ± 20 %3. The lamp frequency should be selected as different as possible from the horizontal synchronous frequency and its harmonics to avoid interference, which may cause line flow on the display 4. The voltage above this value should be applied to the lamps for more than 1 second to start-up. Otherwise the lamps may not be turned on. 5. Calculated value for reference (VBL × IBL) ×2 excluding inverter loss.SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 7 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’4.0 OPTICAL SPECIFICATION4.1 OverviewThe test of Optical specifications shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 30 minutes warm-up period. VDD shall be 5.0V +/-10% at 25°C. Optimum viewing angle direction is 6 ’clock.4.2 Optical Specifications[VDD = 5.0V, Frame rate = 60Hz, Clock = 78MHz, IBL = 7.5mA, Ta =25±2 ℃] ParameterHorizontal Viewing Angle range VerticalSymbolΘ3 Θ9 Θ12 Θ6 Θ3 Θ9 Θ12 Θ6 CR Yw ΔY White Wx Wy Red Rx Ry Green Gx Gy Blue Bx By Tr Tf CTConditionMin.70 70Typ.85 85 80 80 1000 250 80 0.313 0.329 0.644 0.336 0.285 0.593 0.141 0.076 1.5 3.5Max.-UnitDeg. Deg. Deg. Deg. Deg. Deg. Deg. Deg.RemarkCR > 10 70 70 85 CR > 5 85 85 85 700 200 75 0.283 Θ = 0° (Center) Normal Viewing Angle 0.299 0.614 0.306 0.255 0.563 0.111 0.046Note 1Horizontal Viewing Angle range Vertical Luminance Contrast ratio Luminance of White White luminance uniformityNote 2 cd/m2 % 0.343 0.359 0.674 0.366 0.315 0.623 0.171 0.106 2.5 5.5 2.0 ms ms % Note 7 Note 6 Note 5 Note 3 Note 4Reproduction of colorResponse Time Cross TalkRising Falling--SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 8 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’Note :1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface. Contrast measurements shall be made at viewing angle of θ= 0° and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. CR 3. = Luminance when displaying a white raster Luminance when displaying a black raster2.4.5.6.7.Center Luminance of white is defined as the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display. The White luminance uniformity on LCD surface is then expressed as : ΔY = ( Minimum Luminance of 9points / Maximum Luminance of 9points ) * 100 (See FIGURE 2 shown in Appendix). The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Td, and 90% to 10% is Tr. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 4 shown in Appendix).SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 9 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’5.0●INTERFACE CONNECTION.CN11 Module Side Connector : UJU IS100-30O-C23 or Equivalent User Side Connector : JAE FI-X30H or EquivalentSymbol NC CE CTL GND RX0RX0+ GND RX1RX1+ GND RX2RX2+ GND RXCLKRXCLK+ GND RX3RX3+ GND NC NC NC GND GND GND VCC VCC VCC VCC VCC Function No connection No connection No connection GND Ground Negative LVDS differential data input. Channel 0 Positive LVDS differential data input. Channel 0 Ground Negative LVDS differential data input. Channel 1 Positive LVDS differential data input. Channel 1 Ground Negative LVDS differential data input. Channel 2 Positive LVDS differential data input. Channel 2 Ground Negative LVDS differential clock input. Positive LVDS differential clock input. Ground Negative LVDS differential data input. Channel 3 Positive LVDS differential data input. Channel 3 Ground Not connection, this pin should be open. Not connection, this pin should be open. Not connection, this pin should be open. Ground Ground Ground 5V Power supply Remark internal use internal use5.1 Electrical Interface ConnectionPin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 10 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCT 5.2 LVDS Interface (Tx; THC63LVDF83A or Equivalent) 5.2.1 LVDS InterfaceTransmitter Pin No. 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 31 50 2 8 10 16 18 25 Pin No. Interface System (Tx) TFT-LCD (Rx)REV 0ISSUE DATE Dec. 24. 08’Input Signal OR0 OR1 OR2 OR3 OR4 OR5 OG0 OG1 OG2 OG3 OG4 OG5 OB0 OB1 OB2 OB3 OB4 OB5 Hsync Vsync DE MCLK OR6 OR7 OG6 OG7 OB6 OB7 RSVDHT185WX1-100 (CN11) Pin No.Remark48 47OUT0OUT0+RXO0RXO0+1 246 45OUT1OUT1+RXO1RXO1+3 4L V D S42 41OUT2OUT2+RXO2RXO2+5 640 39CLK OUTCLK OUT+RXO CLKRXO CLK+8 938 37OUT3OUT3+RXO3RXO3+10 11SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 11 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’5.3 Data Input Format(1,1) (2,1) (1365,1) (1366,1)R G B R G BR G B R G B1 Pixel = 3 DotsR G BR G B R G B (1,768) (2,768)R G B R G B (1365,768) (1366,768)Display Position of Input Data (V-H)5.4 Back-light Interface Connection●CN 21,22 Module Side Connector User Side Connector :35001HS-02L (Yeon Ho) or Equivalent :35001HS-02L(Yeon Ho) or EquivalentPIN NO. 1 2INPUT HOT COLDCOLOR Pink or Blue White or BlackFUNCTION High Voltage GroundSPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 12 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’6.0 SIGNAL TIMING SPECIFICATION6.1 The HT185WX1-100 is operated by the DE only.Item Frequency Clock High Time Low TimeSymbols 1/Tc Tch TclMinTyp 78Max 95 888 75 13.3 1936 -Unit MHz7784/7Tc 4/7Tc 806 60 16.7 768 1560 1366lines Hz ms lines clocks clocksFrame PeriodTv50 20Vertical Display Period One line Scanning Period Horizontal Display PeriodTvd Th Thd1446 -SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 13 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCT 6.2 LVDS Rx Interface Timing ParameterREV 0ISSUE DATE Dec. 24. 08’The specification of the LVDS Rx interface timing parameter is shown in Table 4. <Table 4. LVDS Rx Interface Timing Specification>Item CLKIN Period Input Data 0 Input Data 1 Input Data 2 Input Data 3 Input Data 4 Input Data 5 Input Data 6 Symbol tRCIP tRIP1 tRIP0 tRIP6 tRIP5 tRIP4 tRIP3 tRIP2 Min 10.60 -0.4 tRCIP/7-0.4 2 ×tRCIP/7-0.4 3 ×tRCIP/7-0.4 4 ×tRCIP/7-0.4 5 ×tRCIP/7-0.4 6 ×tRCIP/7-0.4 Typ 13.25 0.0 tRCIP/7 2 ×tRCIP/7 3 ×tRCIP/7 4 ×tRCIP/7 5 ×tRCIP/7 6 ×tRCIP/7 Max 20.00 +0.4 tRCIP/7+0.4 2 ×tRCIP/7+0.4 3 ×tRCIP/7+0.4 4 ×tRCIP/7+0.4 5 ×tRCIP/7+0.4 6 ×tRCIP/7+0.4 Unit nsec nsec nsec nsec nsec nsec nsec nsec RemarktRIP2 tRIP3 tRIP4 tRIP5 tRIP6 tRIP0 tRIP1 RXz +/* Z = 0, 1, 2,3 RxCLK+Rx3 Rx2 Rx1 Rx0 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0Vdiff=0[v]tRCIPVdiff=0[v]* Vdiff = (RXz+)-(RXz-),…. ,(RXCLK+)-(RXCLK-)SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 14 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’7.0 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL7.1 Sync Timing WaveformsV-SyncOver 3 H-syncH-Sync Fix H-Sync width AreaDE1) Need over 3 H-sync during V-Sync Low 2) Fix H-Sync width from V-Sync falling edge to first rising edge7.2 Vertical Timing WaveformsTv TvdMCLK Th DER7 ~ R0 G7 ~ G0 B7 ~ B0Invalid Datax,1x,2x,yx,1050InvalidDatax+1,1SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 15 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCT 7.3 Horizontal Timing WaveformsREV 0ISSUE DATE Dec. 24. 08’Th Thd MCLK Tc DERA7 ~RA0 GA7 ~GA0 BA7 ~BA0D1D2DnD1048 D1049 D1050InvalidDataD1D2D3TchTcl 2.0V 1.5VMCLK Tds Data0.8VTdh Data 2.0V 0.8VValid TesDE2.0VSPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 16 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORSColor & Gray Scale Black Blue Green Cyan Red Magenta Yellow White Black △ Darker △ ▽ Brighter ▽ Red Black △ Darker △ ▽ Brighter ▽ Green Black △ Darker △ ▽ Brighter ▽ Blue Black △ Darker △ ▽ Brighter ▽ White R7 0 0 0 0 1 1 1 1 0 0 0 R6 0 0 0 0 1 1 1 1 0 0 0 RED DATA R5 R4 R3 R2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 1 1 1 1 1 1 1 1 1 1 1 R1 0 0 0 0 1 1 1 1 0 0 1 GREEN DATA R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 1 1 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 ↑ ↓ 0 1 1 1 1 1 1 0 1 0 0 1 1 1 1 1 1 1 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 ↑ ↓ 1 1 1 1 1 1 1 0 1 1 0 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 B6 0 1 0 1 0 1 0 1 0 0 0 BLUE DATA B5 B4 B3 B2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 1 1 1 1 1 1 1 1 1 1 1 B1 0 1 0 1 0 1 0 1 0 0 0 B0 0 1 0 1 0 1 0 1 0 0 0Basic ColorsGray Scale of REDGray Scale of GREEN1 1 1 0 0 01 1 1 0 0 00 1 1 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 0Gray Scale of BLUE0 0 0 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 10 0 0 0 1 0Gray Scale of WHITE0 0 0 0 0 00 0 0 0 0 00 0 0 0 0 11 1 1 0 0 00 1 1 0 0 11 0 1 0 1 01 1 1 1 1 10 1 11 1 10 1 1 0 1 1SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 17 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’9.0 POWER SEQUENCETo prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below0.9VDD0.9VDD 0.1VDDPower Supply0V0.1VDDT1 T2 Valid0VT3T4Interface SignalT5T6Back- light0V● ● ● ● ● ●0.5 ms ≤ T1 ≤ 10 ms 0 ≤ T2 ≤ 50 ms 0 ≤ T3 ≤ 50 ms 1 sec ≤ T4 200 ms ≤ T5 200 ms ≤ T6Notes:1. When the power supply VDD is 0V, keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid.SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 18 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’10.0 MECHANICAL CHARACTERISTICS10.1 Dimensional Requirements FIGURE 6 (located in Appendix) shows mechanical outlines for the model HT185WX1-100. Other parameters are shown in Table 5. <Table 5. Dimensional Parameters>Parameter Dimensional outline Weight Active area Pixel pitch Number of pixels Back-light Specification Unit mm gram mm mm pixels430.4 ×254.6×16.5 2000 (max.) 409.8(H) × 230.4(V) 0.3(H) ×0.3(V) 1366(H)×768(V) (1 pixel = R + G + B dots) Top / Bottom edge side 2-CCFL type10.2 Mounting See FIGURE 5. (shown in Appendix) 10.3 Anti-Glare and Polarizer Hardness. The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce scratching. 10.4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of 350lux.SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 19 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’11.0 RELIABLITY TESTThe Reliability test items and its conditions are shown in below. <Table 6. Reliability Test Parameters > No 1 2 3 4 5 6 7 Test ItemsHigh temperature storage test Low temperature storage test High temperature & high humidity operation test High temperature operation test Low temperature operation test Thermal shock Vibration test (non-operating) Ta = 60 ℃, 240 hrs Ta = -20 ℃, 240 hrs Ta = 50 ℃, 80%RH, 240hrs Ta = 50 ℃, 240hrs Ta = 0 ℃, 240hrs Ta = -20 ℃ ↔ 60 ℃ (0.5 hr), 100 cycleFrequency Gravity / AMP Period Gravity 10 ~ 300 Hz, Sweep rate 30 min 1.5 G ±X, ±Y, ±Z 30 min Conditions50G 11msec, sine wave±X, ±Y, ±Z Once for each8Shock test (non-operating)Pulse widthDirection9Electro-static discharge test (non-operating)Air : 150 pF, 330Ω, 15 KV Contact : 150 pF, 330Ω, 8 KVSPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 20 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’12.0 HANDLING & CAUTIONS(1) Cautions when taking out the module Pick the pouch only, when taking out module from a shipping package. (2) Cautions for handling the module As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. As the LCD panel and back - light element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care. (3) Cautions for the operation When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the LCD panel would be damaged. Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged. (4) Cautions for the atmosphere Dew drop atmosphere should be avoided. Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended. (5) Cautions for the module characteristics Do not apply fixed pattern data signal to the LCD module at product aging. Applying fixed pattern for a long time may cause image sticking. (6) Other cautions Do not disassemble and/or re-assemble LCD module. Do not re-adjust variable resistor or switch etc. When returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages.SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 21 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’13.0 PRODUCT SERIAL NUMBERHT185WX1-1001 X X X23 X X4 X5 X X X X X6 X X X X X7 X1. 2. 3. 4.Control Number Rank / Grade Line Classification Year (2001 : 01, 2002 : 02, …)5. Month (1,2,3, … , 9, X, Y, Z) 6. Internal Use 7. Serial NumberSPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 22 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’14.0 Packing14.1 Packing OrderSPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 23 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’14.2 Packing Note Box Dimension : 346mm(W) × 521mm(L) × 403mm(H) Package Quantity in one Box : 7pcs14.3 Box label Label Size : 108 mm (L) × 56 mm (W) Contents Model : HT185WX1 Q`ty : Module Q`ty in one box Serial No. : Box Serial No. See next page for detail description. Date : Packing Date FG Code : FG Code of ProductHT185WX1-100 00000000000008 200X.X.XXXXXX00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_noInternal useRoHS MarkSPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 24 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’15.0 APPENDIXFigure 1. Measurement Set Up(L = 5 0 c m )Figure 2. White Luminance and Uniformity Measurement Locations (9 points)13668312291)11)21)3771)41)5384 1) 61)71)81)9691SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 25 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCT Figure 3. Response Time TestingDisplay data White(TFT OFF) TR Optical Response 100% 90% Black(TFT ON)REV 0ISSUE DATE Dec. 24. 08’White(TFT OFF) TF10% 0% TimeFigure 4. Cross Modulation Test DescriptionVIEW AREA VIEW AREA(D/4, W/4)L31(3D/4, 3W/4) (D, W) YA (7D/8,W/2) (D, W)YB(7D/8,W/2)L0 YB - YA YA × 100Cross-Talk (%) =Where:YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location measured will be exactly the same in both patternsSPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 26 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’Figure 5. TFT-LCD Module Outline Dimensions (Front view)SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 27 OF 28 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV 0ISSUE DATE Dec. 24. 08’Figure 6. TFT-LCD Module Outline Dimensions (Rear view)SPEC. NUMBER S864-5040 B2006-5006-O (3/3)SPEC. TITLE HT185WX1-100 Product Specification_Rev.0PAGE 28 OF 28 A4(210 X 297)。