下载文档原格式
铆钉验收标准1、范围本标准规定了各种铆钉的技术条件。
本标准适用于公司使用的所有铆钉。
当技术协议或合同规定与本标准规定不一致时，应以技术协议或合同规定为准。
2、规范性引用文件下列文件对于本文件的应用是必不可少的。
凡是注日期的引用文件，仅所注日期的版本适用于本文件，但是，凡是不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。
GB/T 699 优质碳素结构钢钢号和一般技术条件GB/T 700 普通碳素结构钢技术条件GB/T 715 普通碳素结构钢铆钉用热轧圆钢技术条件GB/T 1220 不锈钢棒GB/T 90 紧固件验收检查、标志与包装YB 451 铆钉用铜线和黄铜线技术条件YB 452 黄铜线技术条件YB 534 冷镦钢技术条件3、材料、热处理及表面处理按表1规定注：①不同冶炼及浇注方法制造的钢料同样可以采用。
②“牌号”栏内每一栏中所列各种材料，可以互通。
③对冷镦钢铆钉应退火处理，并由供需双方协议有关事宜。
5、性能钢铆钉要求硬度HV85-130。
6、形位公差6.1 垂直度6.1.1 铆钉支撑面对钉杆轴心线垂直度公差按图1、表2规定。
注：沉头、半沉头及空心铆钉不予规定。
图16.2 同轴度6.2.1 铆钉钉头对杆轴心线的同轴度公差按图2、表3规定。
图2图37、表面缺陷7.1 铆钉表面不允许有影响使用的裂缝；7.2钉头顶面不允许有影响使用的金属小凸起；7.3不允许有影响使用的圆钝、飞边、碰伤、条痕、浮锈以及杆部末端的压扁。
8、测试方法8.1 钉杆直径检查的测量位置按表5规定。
8.2 铆钉长度l的检查，以短边为准9、验收检查、标志与包装验收检查、标志与包装按GB90规定。
10、上述规定以外的技术条件，由供需双方协议。
序号种类编号规范名称1CCTG法国施工规范第二分册土方工程综述2CCTG法国施工规范第三分册水性粘合剂3CCTG法国施工规范第四分册卷一钢筋及其他金属材料：用于钢筋砼的钢筋4CCTG法国施工规范第4分册卷二金属结构用轧钢5CCTG法国施工规范第四分册卷三金属结构用拧紧螺栓及螺母6CCTG法国施工规范第四分册卷四预应力混凝土用高强钢筋7CCTG法国施工规范第23分册石料8CCTG法国施工规范第24分册沥青粘合剂9CCTG法国施工规范第25分册路体施工10CCTG法国施工规范第26分册沥青层施工11CCTG法国施工规范第27分册沥青混合料的生产施工12CCTG法国施工规范第28分册水泥混凝土施工13CCTG法国施工规范第29分册路面施工及公共空间14CCTG法国施工规范第31分册混凝土或石质路缘边沟15CCTG法国施工规范第32分册便道施工16CCTG法国施工规范第34分册绿化工程17CCTG法国施工规范第35分册绿地，运动娱乐设施18CCTG法国施工规范第36分册照明设施19CCTG法国施工规范第39分册农田排水施工20CCTG法国施工规范第50分册地勘工程及大比例尺图纸21CCTG法国施工规范第56分册金属构造物的防腐工程22CCTG法国施工规范第61分册第4章气候因素,雪对于施工的影响23CCTG法国施工规范第61分册第5章钢结构和桥梁计算及设计24CCTG法国施工规范第62分册第一章钢筋混凝土构造物计算及设计标准25CCTG法国施工规范第62分册第一章预应力混凝土构造物计算及设计标准26欧洲标准0：BS EN1990:2002欧洲规范0：结构设计基础27结构设计基础BS EN1990/A1:2006附录桥梁上的应用（标准化的）28欧洲标准1：BS EN 1991-1-1:2002Part1-1：一般作用——建筑物的容重、自重和作用荷载29BS EN 1991-1-3:2003Part1-3：一般作用——雪荷载30BS EN 1991-1-4:2005Part1-4：一般作用——风作用31BS EN 1991-1-5:2003Part1-5：一般作用——热作用32欧洲标准2：BS EN 1992-1-1:2004Part1-1：一般规定——建筑规则33混凝土结构设计BS EN 1992-1-2:2004Part1-2：一般规定——结构防火设计34BS EN 1992-2:2005Part2：混凝土桥设计和细则35欧洲标准3：BS EN 1993-1-1:2005Part1-1：一般规定——基本规则和房屋建筑的规则36钢结构设计BS EN 1993-1-2:2005Part1-2：一般规定——结构防火设计37BS EN 1993-1-3:2006Part1-3：一般规定——冷铸薄壁构件和板栅的补充规则38BS EN 1993-1-4:2006Part1-4：一般规定——不锈钢的补充规则39BS EN 1993-1-10:2005Part1-10：材料的韧性和垂直板面特性40BS EN 1993-1-11:2006Part1-11：带拉杆结构的设计41BS EN 1993-1-12:2007Part112：钢结构设计EN1993延伸到钢材等级S700的补充规定42BS EN 1993-2:2006Part2：钢桥43欧洲标准4：BS EN 1994-1-1:2004Part1-1：一般规定——通则和房屋建筑规则44钢与混凝土组合结构设计BS EN 1994-1-2:2005Part1-2：一般规定——结构防火设计45BS EN 1996-2:2006Part2：砌体材料的设计、选择和施工46BS EN 1996-3:2006Part3：砌体结构的简明规则和简化计算方法47结构抗震设计BS EN 1998-2:2005Part2：桥梁48BS EN 1998-3:2005Part3：建筑物的加固和修复49铝结构设计BS EN 1999-1-2:2007Part1-2：结构防火设计50BS EN 1999-1-3:2007Part1-3：疲劳敏感性结构。
抽芯铆钉知识大全目录1规格2性能等级标准等3分类4开口型扁圆头抽…5大帽沿不锈钢抽…规格通常规格有2.4 3.2 4 4.8 5 6.4 五个系列.钉芯长度为11个系列6-8--8.5--9.5--11--12--12.5--13--14.5--15.5--16--18--21国内单数的多国外一般是双数市场长度为22---25----30----40不锈钢材料 3.2直径的目前技术可以做到16mm长(前几天在外看到有厂家已经在做3.2*20mm的了,国外有做到28mm 长不过没见过.)4 直径的可以做到25mm长4.8 直径的可以做到40mm长不过通常不怎么用,30mm的用的也是比较少的.6.4直径的和4.8的差不多可以做到40mm长封闭型扁圆头抽芯铆钉(GB12615)市场长度的可以增加 5.5 6 长度.拉丝铆钉目前一般为 4.8*10/14 6.4*14/16/19拉丝铆钉海马乐克钉为 6.4*14/17/19/21 海马乐克钉单/双鼓/多鼓尺寸和一般铆钉差不多性能等级标准等性能等级分为06 08 10 11 12 15 20 21 22 23 30 40 41 50 51 共15个等级.开口型抽芯铆钉按头部形状分沉头和平圆头两种。
其中，性能等级为10级和11级的开口型抽芯铆钉应用较为广泛。
2006年国家标准委修订发布了GB/T 12617.1-2006《开口型沉头抽芯铆钉10、11级》和GB/T 12618.1-2006《开口型平圆头抽芯铆钉10、11级》两项关于10、11级开口型抽芯铆钉的国家标准。
该两项新标准，分别采用ISO15978：2002和ISO15977：2002国际标准，于2006年7月5日发布，于2006年12月1日正式实施。
实施后分别代替GB/T 12617-1990《开口型沉头抽芯铆钉》和GB/T 12618-1990《开口型扁圆头抽芯铆钉》两项旧标准。
一、标准版本的变化原GB/T 12617和GB/T 12618两项关于开口型抽芯铆钉的产品标准首次发布于1990年，本次为第一次修订。
编号中文名称英文名称NF B51-128-1993纤维板.螺钉轴向抽出阻力的测定(FIBREBOARDS. DETERMINATION OF RESISTANCE TO AXIAL WITHDRAWAL OF SCREWS. (EUROPEAN STANDARD EN 320).)NF B51-260-1972木屑板.螺丝拔除试验(PARTICLE BOARD. TEST FOR WITHDRAWAL OF SCREWS.)NF C20-115-1971标定截面不超过2.5mm**2，线芯无特殊预加工的硬铜导线连接的无螺钉接线端(TERMINALS WITHOUT SCREW CLAMPING FOR CONNECTION OFCONDUCTORS FOR FIXED WIRING,WITH A NOMINAL CROSS-SECTIONNOT EXCEEDIND 2,5 MM2, AND WITHOUT SPECIAL PREPARATION OFTHE CONDUCTOR)NF C20-116-1981室外铜导线用螺钉丝端子(Terminals with screw campling for external copper conductors.)NF C60-002-1994家用及类似用低压电路用连接装置.第2-2部分:不带螺钉型夹件的分开的部件连接装置的特别要求(Connecting devices for low voltage circuits for householdand similar purposes. Part 2-2 : particular requirementsfor connecting devices as separate entities with screwless-type clamping units)NF C83-403-803-2003详细规范:防松螺钉不可拆卸的厚度为0.8MM的带扁平触点的矩形连接器(Detail Specification : rectangular connectors - Flatcontacts, 0,8 mm thickness, locking screw not detachable.)NF C93-561-1981电子元件.螺钉锁定的小型同轴接头.一般规定(Components for electronic equipment. Miniature coaxialconnectors with screw coupling. General requirements.)NF C93-566-1981电子元件.螺钉锁定射频用同轴接头（ＫＮ系列）.一般规定(ELECTRONIC COMPONENTS. RF COAXIAL CONNECTORS WITH SCREWCOUPLING (TYPE KN). GENERAL REQUIREMENTS.)法国螺钉标准(NF screw standards)NF C93-578-1996射频连接件.第20部分:外导线内径为13.56mm(0,534 in)同时带有两条内导线的屏蔽平衡电缆用双头螺钉(3/4-20统(Radio-frequency connectors. Part 25 : two-pole screw (3/4-20 unef) coupled connectors for use with shielded balancedcables having twin inner conductors with inner diameter ofouter conductor1356mm(0534in)(type twhn))NF E02-312-1981钢制规.螺丝孔莫氏锥环规(STEEL GAUGES. MORSE TAPER RING GAUGES.) NF E02-316-1981钢制规.螺丝孔５％锥度环规(STEEL GAUGES. METRIC TAPER RING GAUGES.)NF E03-152-1981用极限量规检验螺纹.螺钉用螺纹规(Thread checking with limit gauges. Threaded gauges for screw.)NF E03-154-1970公制三角螺纹.用极限规检验螺纹.螺钉和螺钉孔光滑度检查器(THREAD CHECKING WITH LIMIT GAUGES. PLAIN GAUGES FOR SCREWSAND NUTS.)NF E04-012-1-1996技术制图.螺钉和螺纹部件.第1部分:通用规范(Technical drawings. Screw threads and threaded parts. Part1 : general conventions.)NF E04-012-2-1996技术制图.螺钉和螺纹部件.第2部分:螺纹嵌镶件(TECHNICAL DRAWINGS. SCREW THREADS AND THREADED PARTS. PART2 : SCREW THREAD INSERTS. (EUROPEAN STANDARD EN ISO 6410-2).)NF E04-012-3-1996技术制图.螺钉和螺纹部件.第3部分:简化表示(TECHNICAL DRAWINGS. SCREW THREADS AND THREADS AND THREADEDPARTS. PART 3 : SIMPLIFIED REPRESENTATION. (EUROPEANSTANDARD EN ISO 6410-3).)NF E22-201-1992滚珠螺钉.第1部分:词汇和命名(Ball screws. Part 1 : vocabulary and designation.)NF E22-202-1992滚珠螺钉.第2部分:公称直径和公称引线.米制系列(Ball screws. Part 2 : nominal diameters and nominal leads.Metric series.)NF E22-203-1993球端螺钉.第3部分:合格条件和合格试验(Ball screws. Part 3 : acceptance conditions and acceptance tests.)NF E25-011-1992紧固件的机械特性.由非亚铁金属制造的螺栓,螺钉,柱螺栓和螺母(MECHANICAL PROPERTIES OF FASTENERS. BOLTS, SCREWS, STUDSAND NUTS MADE OF NON-FERROUS METALS. (EUROPEAN STANDARD EN28839).)NF E25-018-2-1994沉头螺钉.第2部分:十字槽(CONTERSUNK FLAT HEAD SCREWS. PART 2 : PENETRATION DEPTHY OF CROSS RECESSES. (EUROPEAN STANDARD EN ISO 7721-2).)NF E25-021-1994螺钉的十字槽(欧洲标准EN ISO 4757)(Cross recesses for screws.)NF E25-022-1-2001紧固件公差.螺栓、螺钉、双头螺栓和螺母.第1部分:产品等级A、B及C(Tolerances for fasteners - Bolts, screws, studs and nuts -Part 1 : product grades A, B and C.)NF E25-022-1987紧固件.Ｆ级螺钉和螺帽公差（精密机械）.螺纹直径1到3mm(FASTENERS. TOLERANCES FOR BOLTS,SCREWS AND NUTS PRODUCTGRADE F (FINE MECHANIC). THREAD DIAMETERS FROM 1 UP TO 3MM.)NF E25-023-1992紧固件.螺栓和螺钉的自由尺寸孔(Fasteners. Clearance hole for bolts and screws.)NF E25-100-1-1999碳钢合金制成的紧固件的机械性能.第1部分:螺栓、螺钉和螺柱(Mechanical properties of fasteners made of carbon steeland alloy steel - Part 1 : bolts, screws and studs.)NF E25-100-3-1992紧固件.表面不连续性.第1部分:一般要求的螺栓、螺钉和螺柱(FASTENERS. SURFACE DISCONTINUITIES. PART 1 : BOLTS, SCREWSAND STUDS FOR GENERAL REQUIREMENTS. (EUROPEAN STANDARD EN26157-1).)NF E25-100-4-1992紧固件.表面不连续性.第3部分:特殊要求的螺栓、螺钉和螺柱(FASTENERS. SURFACE DISCONTINUTIES. PART 3 : BOLTS, SCREWAND STUDS FOR SPECIAL REQUIREMENTS. (EUROPEAN STANDARD EN26157-3).)NF E25-100-5-1998碳钢和不锈钢制紧固件的机械性能.第5部分:不处在拉伸应力下的固定螺钉和类似螺纹紧固件(Mechanical properties of fasteners made of carbon steeland alloy steel. Part 5 : set screws and similar threadedfasteners not under tensile stresses.)NF E25-100-6-1998不锈钢紧固件耐腐蚀的机械特性.螺栓,螺丝和双端螺栓(Mechanical properties of corrosion-resistant stainless-steel fasteners. Part 1 : bolts, screws and studs.)NF E25-100-7-1995紧固件的机械性能.第7部分:公称直径1-10mm的螺栓和螺钉的扭力试验和最小扭矩(MECHANICAL PROPERTIES OF FASTENERS. PART 7 : TORSIONALTEST AND MINIMUM TORQUES FOR BOLTS AND SCREWS WITH NOMINALDIAMETERS 1 MM TO 10 MM. (EUROPEAN STANDARD EN 20898-7).)NF E25-100-8-1998不锈钢紧固件耐腐蚀的机械特性.不低于拉伸应力下配套螺钉和类似紧固件(Mechanical properties of corrosion-resistant stainless-steel fasteners. Part 3 : set screws and similar fastenersnot under tensile stress.)NF E25-107-1983金属用螺钉.内部六叶埋头.Ａ级.符号ＦＸ(SCREWS. SIX LOBES RECESSED CONTERSUNK HEAD. PRODUCT GRADE A. SYMBOL FX.)NF E25-108-2001半埋头内六角螺钉(Hexalobular socket raised countersunk head screws.) NF E25-109-2001平头内六角螺钉(Hexalobular socket pan head screws.)NF E25-110-2001圆柱头内六角螺钉(Hexalobular socket head cap screws.)NF E25-111-2001凸头内六角螺钉(Hexalobular socket cheese head screws.)NF E25-114-2001六角头螺钉.产品等级A和B(Hexagon head bolts - Product grades A and B.)NF E25-115-2-2001六角头螺钉.产品等级C(Hexagon head screws - Product grade C.)NF E25-116-1983金属用螺钉.方头.标准杆.A和B级.符号Q(Square head screws. Product grades A and B. Symbol Q.) NF E25-117-1983金属用螺钉.方头.全螺纹.A和B级.符号Q(Square head screws. Product grades A and B. Symbol Q.) NF E25-118-1983金属用螺钉.方头.C级.符号Q(Square head screws. Product grade C. Symbol Q.)NF E25-119-1-1994带有H型或Z型的十字槽沉头螺钉(普通头型).产品等级A.第1部分:性能类别4.8的钢(Countersunk flat head screws (common head style) with typeH or type Z cross recessed. Product grade A. Part 1 : steelof property class 4.8.)NF E25-119-2-1994十字槽沉头螺钉(一般头形).等级A.第2部分:8.8类特性钢,不锈钢和有色金属(Cross recessed countersunk flat head scews (common headstyle). Grade A. Part 2 : steel of property class 8.8,stainless steel and non-ferrous metals.)NF E25-120-1994带有H型或Z型的十字槽半沉头螺钉(普通头型).产品等级A(Countersunk raised head screws (common head style) withtype H or type Z cross recessed. Product grade A.)NF E25-121-1994带有H型或Z型十字槽的平圆头螺钉.产品等级A(Pan head screws with type H or type Z cross recess.Product grade A.)NF E25-122-1984金属用螺钉.称作“POLIER“的Z十字槽宽圆头.A级.符号RLZ(SCREWS. CROSS RECESSED MUSHROOM HEAD (POELIERS). PRODUCTGRADE A. SYMBOL RL Z.)NF E25-123-1994一字槽沉头螺钉(普通头型).产品等级A (Slotted countersunk flat head screws (common head style). Product grade A.)NF E25-124-1994一字槽半沉头螺钉(普通头型).产品等级A (Slotted raised countersunk head screws (common head style). Product grade A.)NF E25-126-1997内六角圆头螺钉(HEXAGON SOCKET BUTTON HEAD SCREWS. (EUROPEAN STANDARD EN ISO 7380).)NF E25-128-1994一字槽平圆头螺钉.产品等级A(Slotted pan head screws. Product grade A.)NF E25-130-1986加垫圈的金属用螺钉.锥形光滑压紧垫圈.Ａ级(SCREWS WITH CONICAL SPRING TIGHTENING WASHER. PRODUCTGRADE A.)NF E25-131-1986加垫圈的金属用螺钉.内齿锥形垫圈.Ａ级(SCREWS WITH CONICAL SPRING INTERNAL TOOTHED TIGHTENING WASHER. PRODUCT GRADE A.)NF E25-132-1986加垫圈的金属用螺钉.外齿垫圈.Ａ级(SCREWS WITH SERRATED EXTERNAL OVERLAPED TOOTHED LOCK TIGHTENNING WASHER. PRODUCT GRADE A.)NF E25-133-1987紧固件.螺杆千斤顶用的金属螺钉.短六角头长制动端螺钉.Ａ和Ｂ级.符号ＨＺ(Fasteners. Screws for screw-jacks. Small hexagon headscrews with long dog point. Product grades A and B. SymbolHZ.)NF E25-134-1987紧固件.螺杆千斤顶用的金属螺钉.短方头短制动端螺钉.Ａ和Ｂ级.符号ＱＺ(Fasteners. Screws for screw-jacks. Small square headscrews with short dog point. Product grades A and B. SymbolQZ.)NF E25-139-1987紧固件.金属用螺钉.Ｚ十字槽宽凸圆柱形头.Ａ级.符号ＣＢＬＺＳ(FASTENERS. SCREWS. Z CROSS RECESSED AND SLOTTED PAN HEAD.GRADE A. SYMBOL CBL ZS.)NF E25-142-1991紧固件.电阻焊金属螺钉.缩小头(FASTENERS. RESISTANCE WELDING SCREWS. REDUCED HEAD. SYMBOL Z. SR.)NF E25-149-1998十字槽圆头螺钉(CROSS RECESSED CHEESE HEAD SCREWS. (EUROPEAN STANDARD EN ISO 7048).)NF E25-150-1998带平垫圈的螺钉和垫圈组件.垫圈强度等级为200 HV和300 HV.(Screw and washer assemblies with plain washers. Washerhardness classes 200 HV and 300 HV.)NF E25-151-2001米制细牙螺纹的六角头螺钉.产品等级A和B (Hexagon head screws with metric fine pitch thread -Product grades A and B.)NF E25-160-1992平端开槽调整螺钉(SLOTTED SET SCEWS WITH FLAT POINT. (EUROPEAN STANDARD EN 24766).)NF E25-161-1992锥端开槽调整螺钉(SLOTTED SET SCEWS WITH CONE POINT. (EUROPEAN STANDARD EN 27434).)NF E25-162-1992长制动端开槽调整螺钉(SLOTTED SET SCREWS WITH LONG DOG POINT. (EUROPEAN STANDARD EN 27435).)NF E25-163-1992蝶形端开槽调整螺钉(SLOTTED SET SCEWS WITH CUP POINT. (EUROPEAN STANDARD EN 27436).)NF E25-501-2000紧固件公差.第3部分:螺栓、螺钉和螺母用平垫圈.A级和C级(Tolerances for fasteners - Part 3 : plain washers forbolts, screws and nuts - Product grades A and C.)NF E25-520-1998螺丝和洗衣机组件用水平式洗衣机.小型,常规型和大型系列.A级产品(PLAIN WASHERS FOR SCREW AND WASHER ASSEMBLIES. SMALL,NORMAL AND LARGE SERIES. PRODUCT GRADE A. (EUROPEANSTANDARD EN ISO 10673).)NF E25-525-2000通用米制螺栓、螺钉和螺母用平垫圈.一般示意图(Plain washers for metric bolts, screws and nuts forgeneral purposes - General plan.)NF E25-600-1984紧固件.木螺钉系列标准(FASTENERS. WOOD SCREWS FAMILY STANDARD.)NF E25-601-1984十字槽沉头木螺钉.符号FZ(CROSS RECESSED COUNTERSUNK HEAD WOOD SCREWS. SYMBOL FZ.)NF E25-602-1984十字槽沉头木螺钉.符号FBZ (CROSS RECESSED RAISED COUNTERSUNK HEAD WOOD SCREWS. SYMBOL FBZ.)NF E25-603-1984一字槽圆头木螺钉.符号RZ(CROSS RECESSED ROUND HEAD WOOD SCREWS. SYMBOL RZ.)NF E25-604-1984有槽沉头木螺钉.符号FS(Slotted countersunk head wood screws. Symbol FS.)NF E25-605-1984木螺丝.一字槽沉头.FBS符号(Slotted raised countersunk head wood screws. Symbol FBS.) NF E25-609-1985木螺钉.螺丝眼(WOODSCREWS. SCREW-EYES.)NF E25-609-1985木螺钉.螺丝眼(WOODSCREWS. SCREW-EYES.)NF E25-610-1985木螺钉.螺丝钩(WOODSCREWS. SCREW-HOOKS.)NF E25-610-1985木螺钉.螺丝钩(WOODSCREWS. SCREW-HOOKS.)NF E25-611-1985木螺钉.直角弯头螺丝钩(WOODSCREWS. SQUARE BEND SCREW HOOKS.)NF E25-611-1985木螺钉.直角弯头螺丝钩(WOODSCREWS. SQUARE BEND SCREW HOOKS.)NF E25-650-1-1994热处理钢自攻螺钉.机械性能(Heat-treated steel tapping screws. Mechanical properties.) NF E25-650-2-1999自攻螺钉螺纹(Tapping screw thread.)NF E25-651-2003耐腐蚀不锈钢紧固件的机械特性.第4部分:攻丝螺钉(Mechanical properties of corrosion-resistant stainlesssteel fasteners - Part 4 : tapping screws.)NF E25-652-2001沉头内六角攻丝螺钉(Hexalobular socket countersunk head tapping screws.)NF E25-653-2001半埋头(椭圆形)内六角攻丝螺钉(Hexalobular socket raised countersunk (oval) head tapping screws.)NF E25-654-2001平头内六角攻丝螺钉(Hexalobular socket pan head tapping screws.)NF E25-655-1983内六角圆头自攻螺钉.符号RLX (ROUND HEAD TAPPING SCREWS WITH SIX LOBES RECESS. SYMBOL RLX .)NF E25-656-1994十字槽沉头自攻螺钉(普通头型)(Cross recessed countersunk (flat) head tapping screws (common head style).)NF E25-657-1994十字槽半沉头椭圆头自攻螺钉(Cross recessed raised countersunk (oval) head tapping screws.)NF E25-658-1994十字槽平圆头自攻螺钉(Cross recessed pan head tapping screws.)NF E25-659-1984自攻螺钉.十字槽半沉头.(`Poelier`).符号RLZ(TAPPING SCREWS. CROSS RECESSED MUSHROOM HEAD (“POELIER“). SYMBOL RL Z.)NF E25-664-1986一字槽六角头自攻螺钉.符号HS(HEXAGON SLOTTED HEAD TAPPING SCREWS. SYMBOL HS.)NF E25-666-1987紧固件.自攻螺钉.Z形十字槽和一字槽平圆头螺钉.符号CBL ZS(FASTENERS. TAPPING SCREWS. Z CROSS RECESSED AND SLOTTEDPAN HEAD. SYMBOL CBL ZS.)NF E25-755-1997非硬度钢和奥斯特不锈钢的内螺纹平行螺钉(Parallel pins with internal thread, of unhardened steel and austenitic stainless steel.)NF E25-756-1997金属不锈钢和硬化钢的平行螺钉(Parallel pins, of hardened steel and martensitic stainless steel (Dowel pins).)NF E25-757-1997非硬度钢和奥斯特不锈钢的内螺纹平行螺钉(Parallel pins with internal thread, of hardened steel and martensitic stainless steel.)NF E25-800-1-1994紧固件.波纹钢管用螺栓.第1部分:带法兰或不带法兰,带尖或不带尖的六角头螺钉.产品等级A(FASTENERS. BOLTS FOR CORRUGATED STEEL PIPES. PART 1 :HEXAGON HEAD SCREWS WITH OR WITHOUT FLANGE, WITH OR WITHOUTNIBS. PRODUCT GRADE A.)NF E25-800-2-1994紧固件.波纹钢管用螺栓.第2部分:带尖或不带尖的圆头螺钉.产品等级A(FASTENERS. BOLTS FOR CORRUGATED STEEL PIPES. PART 2 :CHEESE HEAD SCREWS, WITH OR WITHOUT NIBS. PRODUCT GRADE A.)NF E25-851-1987紧固件.滚制螺钉(ISO米制螺纹).特性(FASTENERS. THREAD ROLLING SCREWS (ISO METRIC THREAD). PROPERTIES.)NF E27-163-1972调整螺钉(ADJUSTING SCREW.)NF E27-164-1976锁紧螺钉的垫板(LOCKING SCREW.)NF E27-165-1976锁紧螺钉的穿销(SLIDE FOR LOCKING SCREW.)NF E27-166-1976滚花头锁紧螺钉(LOCKING SCREW WITH KNURLED KNOB.)NF E27-167-1976星形手扭锁紧螺钉(LOCKING SCREW WITH PALM KNOB.)NF E27-168-1976四翼锁紧螺钉(LOCKING SCREW WITH 4 ARMED KNOB.)NF E27-170-1974通用滚花头螺钉(GENERAL PURPOSE KNURLED THUMBS SCREWS.) NF E27-191-1983紧固件.有肩固定螺钉(FASTENERS. SHOULDERED RETAINING SCREWS.)NF E27-214-1976带小提琴紧弦用的蝶形螺母锁紧螺钉(LOCKING SCREW WITH VIOLIN TYPE THUMB NUT.) NF E27-215-1976带六角螺母的锁紧螺钉(LOCKING SCREWS WITH HEXAGON NUT.)NF E27-303-1968有孔球头螺钉(SPHERICAL HOLED HEAD SCREW.)NF E27-853-1989通用金属卡箍.带型，无螺钉，不可重复使用(Metallic hose clamps for general purpose. Band type,without screws, non re-usable. Specifications.)NF E27-854-1982通用金属卡箍.带型,无螺钉,可重复使用的销钉卡箍或轴的卡箍(METAL-HOSE CLAMPS FOR GENERAL PURPOSES ; BAND TYPE,WITHOUTSCREWS,RE-USABLE,PIN OR AXLE CLAMPS.)NF E62-307-1977机床构造标准部件.多轴头.防护装置.２８和３６卧式防护装置.支架.行程止推螺钉(MODULAR UNITS FOR MACHINE TOOL CONSTRUCTION. MULTI-SPINDLEHEADS. HORIZONTAL TEMPLATES 28 AND 36. SUPPORTS : STOPSCREW.)NF E62-519-2003柱形扁柄刀具用螺钉压紧刀具夹(立铣刀刀夹).第1部分:刀柄驱动系统的尺寸(Tool chucks (end mill holders) wirth clamp screws forflatted cylindrical shank tool - Part 1 : dimensions of thedriving system of tool shanks.)NF E62-520-2003柱形扁柄刀具用螺钉压紧刀具夹(立铣刀刀夹).带7/24锥柄的夹头尺寸(Tools chucks (end mill holders) wirth clamp screws forflatted cylindrical shank tools - Dimensions of chucks with7/24 taper shank.)NF E62-526-2003带7/24外圆锥和莫氏内圆锥缩径套筒和连接螺钉(Reduction sleeves with 7/24 external and Morse internaltaper and incorporated screw.)NF E63-512-1983铸型和挤压器材.金属模型构件.止动螺钉(MOULDING AND EXTRUSION EQUIPMENT. METALLIC MOULDING ELEMENTS. LOCKING SCREWS.)NF E66-103-1993机用螺丝锥和手动螺丝锥(Short machine taps and hand taps.)NF E66-107-2000公称直径由M3-M10的长杆螺丝攻.由回缩的全直径杆型螺丝攻(Long shank taps with nominal diameters from M3 to M10 -Full-diameter shank taps with recess.)NF E66-108-2000公称直径由M3-M24和1/8-1 英寸的长杆螺丝攻.渐减型螺丝攻(Long shank taps with nominal diameters from M3 to M24 and1/8 in to 1 in - Reduced shank taps.)NF E66-120-1975圆柱和锥形管螺纹手用螺丝锥(HAND TAPS FOR PIPE THREADS FOR PARALLEL AND TAPER THREADS.)NF E66-150-1990ＩＳＯ公制螺纹的手用和机用圆螺丝板牙(Hand- An machine-operated circular screwing dies and hand-operated die stocks.)NF E66-153-1990煤气管道圆柱螺纹手用和机用圆螺丝板牙(Hand-and machine-operated circular screwing dies for parallel pipe threads. G series.)NF E74-303-2001螺钉和螺母组装工具.锻造的和管形套筒扳手.头部外形最大尺寸(Assembly tools for screws and nuts - Forged and tubularsocket wrenches - Maximum outside head dimensions.)NF E74-304-2001螺钉和螺母装配工具.双头开口扳手、双头环形扳手和多用扳手.端部最大宽度(Assembly tools for screws and nuts - Double-headed open-ended wrenches, double-headed ring wrenches and combinationwrenches - Maximum widths of heads.)NF E74-305-2001螺钉和螺母装配工具.双头扳手.尺寸选配(Assembly tools for screws and nuts - Double-ended wrenches - Size pairings.)NF E74-307-2001螺钉和螺母用装配工具.组合扳手.扳手长度和端口最大厚度(Assembly tools for screws and nuts - Combination wrenches- Lengths of wrenches and maximum thickness of heads.)NF E74-310-2001螺钉和螺母用装配工具.工程用双头开口扳手.扳手长度和端口厚度(Assembly tools for screws and nuts - Double-headed open-ended engineers' wrenches - Length of wrenches andthickness of the heads.)NF E74-311-2001螺钉和螺母用装配工具.双头平直套筒扳手和斜口套筒扳手.扳手长度和端口厚度(Assembly tools for screws and nuts - Double-headed, flatand offset, box wrenches - Length of wrenches and thicknessof the heads.)NF E74-313-2001螺钉和螺母用装配工具.双头深斜口套筒扳手和改进的斜口套筒扳手.扳手长度和端口厚度(Assembly tools for screws and nuts - Double-headed, deepoffset and modified offset, box wrenches - Length ofwrenches and thickness of the heads.)NF E74-321-1998螺钉和螺母用装配工具.十字形套筒扳手.尺寸和扭矩试验(ASSEMBLY TOOLS FOR SCREWS AND NUTS. FOUR-WAY SOCKETWRENCHES. DIMENSIONS AND TORQUE TEST.)NF E74-322-1972螺钉螺帽紧固工具.齿条式扳手(ASSEMBLY TOOLS FOR SCREWS AND NUTS.RACK WRENCHES.)NF E74-323-1972螺钉螺帽紧固工具.开槽螺帽用单钩扳手(ASSEMBLY TOOLS FOR SCREWS AND NUTS.HOOK WRENCHES)NF E74-324-2001螺钉和螺母用装配工具.可调扳手(Assembly tools for screws and nuts - Adjustable wrenches.)NF E74-325-2003螺钉和螺母用装配工具.手动转矩工具.设计一致性试验、质量一致性试验和重新校准程序的要求和试验方法(Assembly tools for screws and nuts - Hand torque tools -Requirements and test methods for design conformancetesting, quality conformance testing and recalibrationprocedure)NF E74-331-2003螺钉和螺母用装配工具.内六角扳手(Assembly tools for screws and nuts - Hexagon socket screw keys.)NF E74-351-2002螺钉和螺母用装配工具.一字槽头螺钉用旋具.第2部分:手工操作旋具的一般要求、刀刃长度和标记(Assembly tools for screws and nuts - Screwdrivers forslotted-head screws - Part 2 : general requirements,lengths of blades and marking of hand-operatedscrewdrivers)NF E74-352-1998螺钉和螺母用装配工具.槽螺钉用旋具.第1部分:手工及机械操作用的旋具头(Assembly tools for screws and nuts. Screwdrivers forslotted-head screws. Part 1 : tips for hand- and machine-operated screwdrivers.)NF E74-353-1-2002螺钉和螺母用装配工具.机动旋转头.第1部分:一字槽螺钉旋具(Assembly tools for screws and nuts - Machine-operatedscrewdriver bits - Part 1 : screwdriver bits for slottedhead screws.)NF E74-353-2-2002螺钉和螺母用装配工具.机动旋转头.第2部分:十字槽螺钉旋具头(Assembly tools for screws and nuts - Machine-operatedscrewdrivers bits - Part 2 : screwdriver bits for cross-recessed head screws.)NF E74-353-3-2002螺钉和螺母用装配工具.机动旋转头.第3部分:内六角螺钉用旋具头(Assembly tools for screws and nuts - Machine-operatedscrewdriver bits - Part 3 : screwdriver bits for hexagonsocket screws.)NF E74-354-2002螺钉和螺母用装配工具.螺旋棘轮螺钉旋具头.尺寸(Assembly tools for screws and nuts - Spiral ratchetscrewdriver ends - Dimensions.)NF E74-355-1993十字槽头螺钉用旋转具.第1部分:旋具尖(SCREWDRIVERS FOR CROSS-RECESSED HEAD SCREWS. PART 1 : DRIVERS POINTS.)NF E74-356-1993十字槽头螺钉用旋具.第2部分:手持式旋具的一般要求、旋具头长度和标记(SCREWDRIVERS FOR CROSS-RECESSED HEAD SCREWS. PART 2 :GENERAL REQUIREMENTS, LENGTHS OF BLADES AND MARKING OFHAND-OPERATED SCREWDRIVERS.)NF E74-360-2001螺钉和螺母用装配工具.手动和机动螺丝刀的驱动端和连接部件.尺寸和扭矩试验(Assembly tools for screws and nuts - Drive ends for hand-and machine-operated screwdriver bits and connecting parts- Dimensions, torque testing.)NF E74-360-2001螺钉和螺母用装配工具.手动和机动螺丝刀的驱动端和连接部件.尺寸和扭矩试验(Assembly tools for screws and nuts - Drive ends for hand-and machine-operated screwdriver bits and connecting parts- Dimensions, torque testing.)NF E74-361-1997螺钉和螺母用装配工具.方形旋具.第1部分:手动套筒工具用方形旋具(Assembly tools for screws and nuts. Driving squares. Part1 : driving squares for hand socket tools.)NF E74-362-1997螺钉和螺母用装配工具.方形旋具.第2部分:电动套筒工具用方形旋具(Assembly tools for screws and nuts. Driving squares. Part2 : driving squares for power socket tools.)NF E74-363-1-1997螺钉和螺母用装配工具.方形传动套筒.第1部分:手动套筒.尺寸(Assembly tools for screws and nuts. Square drive sockets.Part 1 : hand-operated sockets. Dimensions.)NF E74-363-2-1997螺钉和螺母用装配工具.方形传动套筒.第2部分:机动“冲击“套筒.尺寸(Assembly tools for screws and nuts. Square drive sockets.Part 2 : machine-operated sockets “impact“. Dimensions.)NF E74-363-3-2001螺钉和螺母用组合工具.方形驱动套筒.第3部分:机器驱动套筒(无冲击).尺寸(Assembly tools for screws and nuts - Square drive sockets- Part 3 : machine-operated sockets (“non impact“) -Dimensions.)NF E74-365-1997螺钉和螺母用装配工具.手动方形传动套筒扳手上的传动件.尺寸和试验(Assembly tools for screws and nuts. Driving parts forhand-operated square drive socket wrenches. Dimensions andtests.)NF E74-366-1997螺钉和螺母用装配工具.手动方形传动套筒扳手上的附件.尺寸和试验(Assembly tools for screws and nuts. Attachments for hand-operated square drive socket wrenches. Dimensions andtests.)NF E74-367-1995螺钉和螺母用装配工具.机动插头扳手的方块传动加长六角插头(Assembly tools for screws and nuts. Square drive extensionhexagon insert, for power socket wrenches.)NF E74-381-1997螺钉和螺母用装配工具.技术规范.第1部分:手动扳手和套筒(Assembly tools for screws and nuts. Technicalspecifications. Part 1 : hand-operated wrenches andsockets.)NF E82-020-1984模压锻造零件.拉紧装置用灯的螺钉.规范(DROP FORGINS. EYEBOLTS FOR TURNBUCKLES. REQUIREMENTS.)NF F01-088-1971铁路运输设备.带有槽端头和螺纹端头的未钻孔轴.头部钻孔的螺钉(RAILWAY TRANSPORT EQUIPMENT. UNBORED AXLES WITH SLOTTEDAND THREADED ENDS. SCREWS WITH DRILLED HEADS.)NF F03-004-1983铁路车辆.金属螺钉. 沉头和半沉头. Ａ级.符号Ｆ和ＦＢ(Railway rolling stock. Grade A. Countersunk and raisedcountersunk notched head machine screws. Symbols F and FB.)NF F03-005-1983铁路车辆.金属螺钉. 圆柱头和球面圆柱头.Ａ级. 符号Ｃ和ＣＲ(Railway rolling stock. Grade A. Notched cheese head ornotched dome head machine screws. Symbols C and CR.)NF F03-006-1983铁路车辆.开槽懦半沉头螺钉一螺母. Ａ级.符号ＦＢＰ(Railway rolling stock. Grade A. Slotted or notched raisedcountersunk head screws nuts. Symbol FBP.)NF F03-016-1983铁路车辆.开槽沉头螺钉, 螺母. Ａ级. ＦＰ(Railway rolling stock. Grade A. Slotted countersunk headscrews nuts. Symbol FP.)NF F10-404-1984铁路车辆.0.25MN的联接螺钉(Railway transport equipment. Coupling screw of 0,25 mn.)NF F11-003-1970铁路车辆.手制动. 螺钉和螺母. 螺距和螺纹剖面. 螺钉传动(RAILWAY TRANSPORT EQUIPMENT. HAND BRAKE. SCREWS AND NUTS.PITCHES AND PROFILES. SCREW DRIVES.)NF F50-006-1998铁路固定设备.带可变螺纹的枕木螺丝(Railway fixed equipment. Sleeper screws with variable thread.)NF F55-251-1991铁路固定设备.信号电路.连接和分段器材.螺钉连接部件(RAILWAY FIXED EQUIPMENT. SIGNALLING. CIRCUITS. CONNECTINGAND BREAKING COMPONENTS. SCREW-TYPE TERMINAL BLOCKS.)NF F56-123-1980铁路固定设备.通讯和信号装置架空线路用器材.直径口毫米镀锌方头木螺钉(FIXED RAILWAY INSTALLATIONS. EQUIPMENT FOR OVERHEADTELECOMMUNICATION AND SIGNALLING LINES. GALVANIZED SQUAREHEAD WOOD SCREWS.)NF J41-465-1957造船工业.“金士顿“阀门.螺钉零件(SHIPBUILDING. KINGSTON VALVES. BOLTS AND SCREWS.)NF J46-126-1951造船工业.空气入口.手柄和紧固螺钉(SHIPBUILDING. VENTILATORS. HANDLE AND LOCKING SCREW.) NF L22-063-1970用板手操作的螺母、螺钉和轴的间隙(CLEARANCE FOR WRENCHING NUTS,SCREWS AND PINS.)NF L22-070-1976螺钉的BNAE型十字槽(CROSS RECESS (B.N.A.E.).)NF L22-071-1976NFL ２２-０７０ 型螺钉十字槽用螺丝刀头(SCREW-DRIVER END FOR CROSS RECESS ACCORDING TO NF L 22-070.)NF L22-071-1976NFL ２２-０７０ 型螺钉十字槽用螺丝刀头(SCREW-DRIVER END FOR CROSS RECESS ACCORDING TO NF L 22-070.)NF L22-072-1991航天建筑.螺丝.920型十字槽(Aerospace construction. Bolts and screws. 92 degrees cruciform recess.)NF L22-090-1966修配用大直径标准螺钉、销和垫圈(STANDARDIZED SCREWS,PINS AND WASHERS WITH INCREASED DIAMETER INTENDED FOR REPAIR WORK.)NF L22-111-1975无销孔六角头螺钉.国际单位制螺纹(Hexagon head bolts without split pin hole. Sim thread (rech.).)NF L22-112-1975带销孔六角头螺钉.国际单位制螺纹(Hexagon head bolts with split pin hole. Sim thread (rech.).)NF L22-121-1975带轻杆无锁孔六角头螺钉.国际单位制螺纹(Hexagon head bolts with waisted shank without split pin hole. Sim thread (rech.).)NF L22-122-1975带轻杆有销孔六角头螺钉.国际单位米制螺纹(Hexagon head bolts with waisted shank with split pin hole.Sim thread.)NF L22-125-1985六角头承拉螺钉ISO 螺纹４h 类(Bolt, hexagonal head, for tensile application, . ISO thread 4H class.)NF L22-126-1985带锁紧孔六角头承拉螺钉.ISO螺纹４h 类(Bolt, hexagonal head, with locking hole, for tensile application. ISO thread 4H class.)NF L22-127-1985带颈杆六角头承拉螺钉.ISO螺 纹４h 类(Bolt, hexagonal head, necked shank, for tensile application. ISO thread 4H class.)NF L22-128-1985带颈杆有锁紧孔六角头承拉螺钉.ISO 螺纹４h 类(Bolt, hexagonal head, necked shank, with locking hole, fortensile application. ISO thread 4H class.)NF L22-129-1985带销孔六角头承拉螺钉.ISO 螺纹４h 类(Bolt, hexagonal head, with split pin hole, for tensile application. ISO thread 4H class.)NF L22-134-1975无销孔六角头槽制螺钉.国际单位制螺纹(Precision hexagon head bolts without split pin hole. Sim thread (rech.).)NF L22-135-1975带销孔六角头槽制螺钉.国际单位制螺纹(Precision hexagon head bolts with split pin hole. Sim thread (rech.).)NF L22-136-1984通用六角头螺钉短螺纹(Bolt, hexagonal head, current use, short thread.)NF L22-137-1984带锁紧孔六角头短螺纹螺钉(Bolt, hexagonal head, with locking hole, short thread.) NF L22-138-1984精密六角头短螺纹螺钉(Bolt, hexagonal head, close tolerance, short thread.)NF L22-139-1984带锁紧孔精密头角头短螺纹螺钉(BOLT,HEXAGONAL HEAD,CLOSE TOLERANCE,WITH LOCKING HOLE,SHORT THREAD.)NF L22-140-1984六角头全螺纹螺钉(Bolt, hexagonal head, threaded to head.)NF L22-141-1984有锁紧孔方角头全螺纹螺钉(Bolt, hexagonal head, with locking hole, threaded to head.)NF L22-142-1984常用有销孔六角头螺钉(BOLT,HEXAGONAL HEAD,WITH COTTER PIN HOLE,CURRENT USE.)NF L22-145-1985六角头承拉螺钉.ISO螺纹4G类(Bolt, hexagonal head, for tensile application, ISO thread 4G class.)NF L22-146-1985有锁紧孔六角头承拉螺钉.ISO螺纹4G类(Bolt, hexagonal head, with locking hole, for tensile application. ISO thread 4G class.)NF L22-147-1985带颈杆六角头承拉螺钉.ISO螺纹4G类(Bolt, hexagonal head, necked shank, for tensile application. ISO thread 4G class.)NF L22-148-1985带颈杆有销紧孔六角头承拉螺钉.ISO螺纹4G类(Bolts, hexagonal head, necked shank, with locking hole,for tensile application. ISO thread 4G class.)NF L22-151-1975开槽圆柱头螺钉和紧固凸圆头螺钉.国际单位制螺纹(Slotted and drilled cheese head screws. Sim thread(rech.).)NF L22-152-1975开槽扁头螺钉.国际单位米制螺纹(Slotted mushroom head screws. Sim thread (rech.).)NF L22-153-197590°埋头开槽螺钉.国际单位米制螺纹(Slotted 90 degrees countersunk head screws. Sim thread (rech.).)NF L22-154-1975120°半圆头开槽埋头螺钉.单际单位米制螺纹(Slotted raised 120 degrees countersunk head screws. Simthread (rech.).)NF L22-156-1975锥顶凸圆头开槽螺钉.国际单位米制螺纹(Slotted raised cheese head screws with cone point. Sim thread (rech.).)NF L22-157-1975锥顶扁头开槽螺钉.国际单位米制螺纹(Slotted mushroom head screws with cone point. Sim thread (rech.).)NF L22-158-1975锥顶90°埋头开槽螺钉.国际单位米制螺纹(Slotted 90 degrees countersunk head screws with cone point. Sim thread (rech.).)NF L22-159-1975锥顶120°半圆头开槽埋头螺钉.国际单位米制螺纹(Slotted raised 120 degrees countersunk head screws withcone point. Sim thread (rech.).)NF L22-161-1984有NF L22-72十字槽的通用100°埋头螺钉(Bolt, 100 degrees countersunk head, current use, nf L 22-072 cross recess.)NF L22-162-1984有NF L22-072十字槽的精密100°全螺纹埋头螺钉(Bolt, 100 degrees countersunk head, close tolerance, nf L22-072 cross recess.)NF L22-163-1984有NF L22-072十字槽的常用100°度全螺纹埋头螺钉(Bolt, 100 degrees countersunk head, threaded to head, nf L22-072 cross recess.)NF L22-167-1984有NF L22-070十字槽的常用100°埋头螺钉(Bolt, 100 degrees countersunk head, current use, nf L 22-070 cross recess.)NF L22-168-1984有NF L22-070 十字槽的紧公差100°沉头螺钉(BOLT,100 DEGREES COUNTERSUNK HEAD,CLOSE TOLERANCE,NF L 22-070,CROSS RECESS.)NF L22-169-1984有 NF L22-070十字槽的100°全螺纹埋头螺钉(BOLT,100 DEGREES COUNTERSUNK HEAD,THREADED TO HEAD,NF L22-070,CROSS RECESS.)NF L22-171-1984有NF L22-072十字槽的常用半圆头螺钉(Bolt, pan head, current use, nf L22-072 cross recess.) NF L22-173-1984有NF L22-072十字槽全螺纹半圆头螺钉(BOLT,PAN HEAD,THREADED TO HEAD,NF L 22-072 CROSS RECESS.)NF L22-176-1984有NF L22-072十字槽锥顶半圆头非磁性螺钉(Bolt, pan head, amagnetic with cone point NF L 22-072 cross recess.)NF L22-177-1984有NF L22-070十字槽常用半圆头螺钉(Bolt, pan head, current use, nf L 22-070 cross recess.) NF L22-179-1984有NF L22-070十字槽全螺纹半圆头螺钉(BOLT,PAN HEAD,THREADED TO HEAD,NF L 22-070 CROSS RECESS.)NF L22-181-1976有BNAE十字槽扁头螺钉.国际单位米制螺纹(MUSHROOM HEAD SCREWS WITH B.N.A.E. CROSS RECESS. SIM THREAD.)NF L22-182-1976有BNAE十字槽90°埋头螺钉.国际单位米制螺纹(90 DEGREES COUNTERSUNK HEAD SCREWS WITH B.N.A.E. CROSSRECESS. SIM THREAD.)NF L22-183-1976有BNAE十字槽90°埋头螺钉.国际单位米制螺纹(RAISED 120 DEGREES COUNTERSUNK HEAD SCREWS WITH B.N.A.E.CROSS RECESS. SIM THREAD.)NF L22-184-1976有BNAE十字槽120°埋头螺钉.国际单位米制螺纹(120 DEGREES COUNTERSUNK HEAD SCREWS WITH B.N.A.E. CROSSRECESS. SIM THREAD.)NF L22-186-1976有BNAE十字槽锥顶扁头螺钉.国际单位米制螺纹(MUSHROOM HEAD SCREWS WITH B.N.A.E. CROSS RECESS AND CONEPOINT. SIM THREAD.)NF L22-187-1976有BNAE十字槽锥顶90°埋头螺钉.国际单位米制螺纹(90 DEGREES COUNTERSUNK HEAD SCREWS WITH B.N.A.E. CROSSRECESS AND CONE POINT. SIM THREAD.)NF L22-188-1976有BNAE十字槽锥顶120°埋头半圆头螺钉单国际单位制米螺纹(RAISED 120 DEGREES COUNTERSUNK HEAD SCREWS WITH B.N.A.E.CROSS RECESS AND CONE POINT. SIM THREAD.)NF L22-189-1976有BNAE十字槽锥顶120°埋头螺钉.国际单位米制螺纹(120 DEGREES COUNTERSUNK HEAD SCREWS WITH B.N.A.E. CROSSRECESS AND CONE POINT. SIM THREAD.)NF L22-201-1984短螺纹精密螺钉.六角头.ISO螺纹(Bolt, hexagonal head, short thread, close tolerance. ISO thread.)。
欧美地区锚栓相关标准欧美锚栓相关标准1．欧洲标准欧洲标准主要包括欧洲技术认证组织（EOTA）颁布的欧洲技术认证指南ETAG 001和相关的技术报告（Technical Report），列举如下。
其中红色标记的文件涉及锚栓或植筋的设计。
其余文件主要和测试认证相关。
ETAG 001 混凝土用金属锚栓-Part 1 锚栓概述-Part 2 扭矩控制式膨胀锚栓-Part 3 扩孔型（GB 50367中称后扩底）锚栓-Part 4 位移控制式膨胀锚栓-Part 5 粘结锚栓（或称化学锚栓）-Part 6 用于非结构应用中冗余系统的锚栓ETAG 001另有３个附录-Annex A 测试的细节-Annex B 允许使用条件测试-Annex C 锚栓的设计方法（针对机械锚栓）ETAG还有若干锚栓相关的技术报告-TR 018 扭矩控制式粘结锚栓（即GB 50367和GB 50550中所称“定型化学锚栓”和“特殊倒锥型锚栓”）-TR 020 混凝土中锚固的抗火性能评估方法-TR 023植筋连接的评估方法-TR 029 化学锚栓的设计方法2．美国规范美国规范主要包括美国混凝土协会（ACI）和美国国际规范协会（ICC）的相关标准，列举如下。
其中红色标记的文件涉及锚栓的设计。
其余文件主要和测试认证相关。
ACI标准ACI 355.2混凝土用后置机械锚栓的判定ACI 318 Appendix D混凝土结构设计规范附录DICC标准AC 193混凝土用机械锚栓的验收标准AC 308混凝土用后置粘结锚栓的验收标准3．具体的产品认证报告由EOTA颁发的欧洲技术认证ETA以及由ICC颁发的ICC评估认证是国际范围内接受度最高的两种认证。
这两种认证会对特定的某种锚栓进行测试评估，满足标准要求的颁发相应认证证书。
证书中会指定该锚栓适合采用的设计方法以及设计时需要的特定参数。
ICC认证中还会给出该锚栓设计的例题。
所以，除了标准中的相关规定外，产品认证中的数据也很重要，其内容比标准更具体和实用。
