众冠 _电木-MSDS

物质安全资料表 MSDS版本 (Rev.) A/0页码 (page)第 1 页，共4页一、物品与厂商资料/Product and Company Identification 物品名称：黑色导电泡棉Product Name ：black conduct electricity foam制造商或供货商名称、地址及电话：鉅冠协创（深圳）科技有限公司Address & Tel. of Manufacturer or Agent 广东省深圳市宝安区石岩镇塘头大道宏发高新园三栋四楼西侧 紧急联络电话/传真电话：+86-0755-******** / +86-0755-******** Emergency Phone Number/Fax二、成分辨识资料/Composition, Information on Ingredients 成分名称 Component Chemical Name &Common Names ：浓度(成分百分比)Concentration (Percentage)：CAS NO导电布 30% 65997-17-3 PU 泡棉65% /Acrylic 5% 9011-14-7三、危害辨识数据/ Hazard Identification 最重要危害效应 Most Important Health Hazards and Reactions健康危害效应/Health Hazards and Reactions ：无环境影响/Environmental Impact ：合理回收,不会造成环境污染 物理性及化学性危害/Physical and Chemical Hazards ： 无 特殊危害/Specific Hazards ： 无主要症状/Cardinal Symptoms ： 无 物品危害分类/Hazard Classification ： 无四、急救措施/ First Aid Measures不同暴露途径之急救方法/ First Aid Measures for Different Kinds of Exposures ： ˙吸入/Inhalation ：无 ˙皮肤接触/Skin Contact ：无 ˙眼睛接触/Eye Contact ：无 ˙食入/Ingestion ： 无最重要症状及危害效应/Most Important Symptoms and Hazard Reactions ： 无 对医师之提示/Suggestions to Doctors ： 无项目(Subject): 物质安全资料表 MSDS物质安全资料表 MSDS 版本 (Rev.) A/0 页码 (page) 第 2 页，共4页五、灭火措施/ Fire Fighting Measures适用灭火剂/Suitable Extinguishing Media：一般灭火器灭火时可能遭遇之特殊危害/Special Hazards in Fire：无特殊灭火程序/Special Fire-Fighting Procedures：移除可燃物消防人员之特殊防护设备/Required Special Protective Equipment for Fire-Fighters：无六、泄漏处理方法/ Accidental Release Measures个人应注意事项/ Personal Precautions：无环境注意事项/Environmental Precautions：尽快废弃处理收集起来的物质。

物质安全资料表(MSDS)一、 制造商或供应商资料制造商或供应商名称：制造商或供应商地址：咨询者姓名及电话：紧急联络电话：传真电话：二、 材料分析物品中（英）文名称：Epoxy Resin同义名称：环氧树脂光电浇注料材料分析：中 文 名 称 化 学 式 比例CAS.NO.1.双酚A型环氧树脂C2H3O-[C18H20O3]n C15H14O2- C2H3O95% 25068-38-62.环氧稀释剂R-C2H3O2% 68609-97-23.添加剂/ 3% /WL-819B（NH）1.酸酐类固化剂C9H12O395% 19438-60-92.促进剂C15H27N3O 5% 90-72-2三、物理及化学特性物质状态：【 】糊状物【 】粉末【 】固体【√】液体【 】气体 PH值：NA外 观：淡紫色透明液体 气 味： NA沸 点：℃NA 蒸汽压： NA mmHg蒸汽密度（空气=1）：NA 比 重（水=1）： 1. 15±0.005挥发速率（乙酸丁酯=1）：NA 水中溶解度： NA四、火灾及爆炸危害资料闪火点：℉＞140 ℃ 爆炸界限 爆炸上限（UEL）： NA % 测试方法： 【 √ 】 开杯 【 】 闭杯爆炸下限（LEL）： NA %火灾 灭火材料：1211、干粉、二氧化碳、泡沫 特殊灭火程序NA五、 反应特性安 定 性 【√ 】 安定 应避免之状况：NA危害分解物：NA【 】 不安定危害之聚合 【 】 可能发生 应避免之状况：NA 【√ 】 不会发生不 相 容 性 应避免之物质：NA六、健康危害及急救措施进入人体之途径 【 √ 】吸入 【 √ 】 皮肤接触 【√ 】 吞食健康危害效应 急性：吸入：蒸气会刺激呼吸道，会造成呕吐，食欲不振接触：造成轻微的刺激眼睛：造成轻微的刺激食入：会造成呕吐，食欲不振慢性：暴露之微兆及症状紧急处理及急救措施 1.吸入蒸气后，须立即将患者移至新鲜空气处。

2.呼吸停止，应立即由受过训练之人施以人工呼吸。

电木粉（镶嵌粉）MSDS物质安全表酚醛树脂【英文名称】phenolic resin【中文同义词】镶嵌粉9003-35-4危险性概述回目录【健康危害】接触加工或使用本品过程中所形成的粉尘，可引起头痛、嗜睡、周身无力、呼吸道粘膜刺激症状、喘息性支气管炎和皮肤病，还可发生肾脏损害。

空气环境分析发现苯酚、甲醛和氨。

在缩聚过程中，可发生甲醛、酚、一氧化碳中毒。

【燃爆危险】本品易燃，具刺激性。

急救措施回目录【皮肤接触】脱去污染的衣着，用肥皂水和清水彻底冲洗皮肤。

【眼睛接触】提起眼睑，用流动清水或生理盐水冲洗。

就医。

【吸入】迅速脱离现场至空气新鲜处。

保持呼吸道通畅。

如呼吸困难，给输氧。

如呼吸停止，立即进行人工呼吸。

就医。

【食入】饮足量温水，催吐。

就医。

消防措施回目录【危险特性】易燃，遇明火、高热能燃烧。

受高热分解放出有毒的气体。

粉体与空气可形成爆炸性混合物, 当达到一定浓度时, 遇火星会发生爆炸。

【有害燃烧产物】一氧化碳、二氧化碳。

【灭火方法】喷水冷却容器，可能的话将容器从火场移至空旷处。

灭火剂：雾状水、泡沫、二氧化碳、干粉、砂土。

泄漏应急处理回目录【应急处理】迅速撤离泄漏污染区人员至安全区，并进行隔离，严格限制出入。

切断火源。

建议应急处理人员戴自给正压式呼吸器，穿防静电工作服。

若是液体。

尽可能切断泄漏源。

防止流入下水道、排洪沟等限制性空间。

小量泄漏：用干燥的砂土或类似物质吸收。

大量泄漏：构筑围堤或挖坑收容。

用泡沫覆盖，降低蒸气灾害。

用防爆泵转移至槽车或专用收集器内，回收或运至废物处理场所处置。

若是固体，收集于干燥、洁净、有盖的容器中。

然后在专用废弃场所深层掩埋。

若大量泄漏，收集回收或运至废物处理场所处置。

操作处置与储存回目录【操作注意事项】密闭操作。

密闭操作，提供良好的自然通风条件。

操作人员必须经过专门培训，严格遵守操作规程。

建议操作人员佩戴自吸过滤式防尘口罩，戴化学安全防护眼镜，穿防静电工作服。

远离火种、热源，工作场所严禁吸烟。

Material Safety Data Sheet材料安全数据表 Version Date: 2009-08-01Page: 1 / 3Synonyms ： Phenolic Molding Compound, PMC 物品名称： 酚醛模塑料，电木粉成型材料 Chemical Family ：Phenolic resin 化学品分类：酚醛树脂基Ⅰ——Information on IngredientⅡ——Physical Characteristics Wood flourSection Ⅲ——Health Hazard Data 部分Ⅲ——常温下危害健康数据 Effects of Overexposure: 暴露状态下的危害性This product may cause skin sensitization which may be evidenced bya rash. 这种产品可能使皮肤搔痒，经证实将有可能产生过敏。

Emergency and First Aid Procedures: 应急程序 In case of skin contact, wash affected area thoroughly with soap and water. 如果接触皮肤，则可用肥皂或清水直接清理患处。

In case of eye contact, immediately irrigate with plenty of water for 15 minutes.如果接触眼睛，则立即用大量的清水冲洗患处大约15分钟。

In case of inhalation overexposure, move to fresh air until overexposure effects subside.如果过度吸入气体，则移动至新鲜空气处，直至不适感消失。

If swallowed, drink plenty of water. Get immediate medical attention.如果不慎进入食入，需饮用大量的水清洗，紧急送至医院治疗。

塑胶五金机构件物质安全资料表MSDS物质安全资料表MSDS一、物品与厂商资料物品名称：物品编号：制造商名称:地址：联系电话：二、成分辨识资料组成部分物质名称CAS编号含量危害物质分类胶壳UP 樹脂32762-75-725~30%N/A 填充粉（ATH）21645-51-245~55%N/A 玻璃纖維65997-17-320~30%N/A引脚Fe7439-89-683~90%N/A Cu7440-50-88~13%N/A Sn7440-31-5 1.5~3%N/A Ni7440-02-00.5~1%N/A三、危害辨识资料最重要危害效应健康危害效应：N/A环境影响：N/A物理性及化学性危害：N/A 特殊危害：N/A主要症状：物品危害分类：四、急救措施不同暴露途径的急救方法：吸入：本品为固体，不适用皮肤接触：本品无毒，不适用食入：若不慎吞食，立即送医院救治眼晴接触：本品无毒，不适用最重要症状及危害效应：N/A对急救人员的防护：N/A对医师的提示：N/A五、灭火措施适用灭火器：水雾，泡沫，二氧化碳和干粉灭火时可能遭遇的特殊危害：呼吸道不适灭火方法：N/A消防人员的特殊防护设备：在密闭的空间，消防员应该穿着全套防护设备，包括具有压力之呼吸器具。

六、泄漏处理方法个人应注意事项：N/A环境注意事项：N/A清理方法：N/A七、安全处置与储存方法处置：N/A储存：为保存证品质，请将本品存放于干燥环境中八、暴露预防措施工程控制：N/A控制参数：八小时日时量平均容许浓度/短时间时量平均容许浓度/最高容许浓度：N/A生物指标：N/A个人防护设备：N/A眼睛防护：N/A 呼吸防护：N/A皮肤及身体防护：N/A手部防护：N/A卫生措施：N/A九、物理及化学性质物质状态：固态形状：N/A颜色：本体黑色气味：N/A沸点：N/A分解温度：N/A自燃温度：N/A蒸气压：N/A密度:N/A溶解度:N/A十、安定性及反应性安定性：稳定特殊状况下可能的危害反应：N/A应避免的状况：高温高湿应避免的物质：强氧化剂，强酸危害分解物：燃烧可释放出一氧化碳、二氧化碳、氮氧化物十一、毒性资料急毒性：N/A食入：N/A吸入：N/A LD50(测试动物、呼吸途径）：N/A皮肤：N/A局部效应：N/A眼睛：N/A致敏感性：N/A十二、生态资料可能之环境影响：N/A十三、废弃处置方法：废弃处置方法：依政府或地方环保法规十四、运送资料国际运送法规定：N/A国内运送规定：N/A特殊运送方法及注意事项：N/A十五、法规资料适用法规：N/A十六、其他资料参考文献制表单位N/A名称：地址：电话：制表人：姓名(签章)：制表日期：职称：。

MATERIAL SAFETY DATA SHEETSWANCOR IND. CO., LTD.NO. 9 INDUSTRY SOUTH 6 ROAD,NAN-KANG INDUSTRIAL PARK,NAN-TOU CITY, TAIWAN 54066 R.O.C.TEL: 886-49-2255420FAX: 886-49-2251534E-MAIL: swancor@MSDS NO.: NT27-222-EISSUE DATE: 03/10/2006PREPARED BY: MARK HUANGSECTION I - IDENTITY INFORMATIONPRODUCT NAME: SWANCOR CP-95PRODUCT TYPE: Vinyl Ester ResinUN/NA NUMBER: UN1866HAZARD RATING: Health 2 / Flammability 3 / Reactivity 2SECTION II - COMPOSITION ON INGREDIENTSIngredient Percent CAS Index No.Vinyl Ester Resin 50~55 036425-16-8Styrene 45~50 000100-42-5SECTION III - HAZARDS IDENTIFICATIONEMERGENCY OVERVIEW:Straw-yellow viscous liquid. Pungent styrene odor. Flammable. Reactive. Causes eye irritation. Highly toxic to fish and/or other aquatic organismsPOTENTIAL HEALTH EFFECTS:Refer to Section XI for toxicological data, Effects of Overexposure: for styreneEYE CONTACT:May cause moderate eye irritation. May cause slight corneal injury. Vapors may irritate eyes. Vapors may cause lacrimation (tears). SKIN CONTACT:Prolonged or repeated exposure may cause skin irritation. Material may stick to skin causing irritation upon removal. A single prolonged exposure is not likely to result in the material being absorbed through skin in harmful amounts.INGESTION:Single dose oral toxicity is considered to be low. If aspirated (liquid enters the lung), may be rapidly absorbed through the lungs and result in injury to other body systems.INHALATION:Excessive vapor concentrations are attainable and could be hazardous on single exposure. Signs and symptoms of excessive exposure may be anesthetic or narcotic effects and result in injury to other body systems.SYSTEMIC (OTHER TARGET ORGAN) EFFECTS:Contains styrene, which, in animals, has been reported to cause effects on the following organs; central nervous system, kidney, liver and reparatory tract. Lung effects have been observed in mice following repeated exposure to styrene. Styrene is reported to have caused hearing loss in laboratory animals upon exposure to high concentrations (>600 ppm); however, the relevance of this to humans is unknown. Some studies in humans allege that repeated exposure to styrene may result in minor subclinical decreases in the ability to discriminate between colors.CANCER INFORMATION:This mixture contains a component (s) which are listed as potential carcinogens for hazard communication purposes under OSHA Standard 29 CFR 1910.1200. Component(s) listed by IARC; styrene. An increased incidence of lung tumors was observed in mice from a recent inhalation study on styrene. The relevance of this finding to humans is uncertain since data from other long-term animal studies and from epidemiology studies of workers exposed to styrene do not provide a basis to conclude that styrene is carcinogenic. TERATOLOGY:In laboratory animals, styrene did not produce birth defects or any other effects on the fetus even at exposure concentrations having an adverse effect on the mother.REPRODUCTIVE EFFECTS:Contains component(s) which did not interfere with reproduction in animal studies. The component(s) is/are: styrene.SECTION IV - FIRST AIDS PROCEDURESSKIN CONTACT:Thoroughly wash exposed area with soap and water immediately. Remove contaminated clothing. Launder contaminated clothing before re-use.EYE CONTACT:Flush with large amount of water immediately and continuously for 20 minutes, lifting upper and lower lids occasionally. Get medical attention.INGESTION:Do not induce vomiting. Keep person warm, quiet and get medical attention. Aspiration of material into the lungs can cause chemical pneumonitis which can be fatal.INHALATION:If affected, remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration. Keep person warm, quiet, and get medical attentionNOTE TO PHYSICIAN:Because rapid absorption may occur through lungs if aspirated and cause systemic effects, the decision of whether to induce vomitingor not should be made by an attending physician. If lavage is performed, suggest endotracheal and/or exophageal control. Danger from lung aspiration must be weighed against toxicity when considering emptying the stomach. No Specific antidote. Supportive care. Treatment based on judgment of the physician in response to reactions of the patient.SECTION V - FIRE FIGHTING MEASURESFlash Point 88o F (31o C) for StyreneFlammable Limits Lower : 1.1% (For Styrene)Upper : 6.1% (For Styrene)HAZARDOUS DECOMPOSITION PRODUCT:May form toxic materials: carbon dioxide and carbon monoxide, various hydrocarbons.OTHER FLAMMABILITY INFORMATION:Dense smoke is produced when product burns. Violent steam generation or eruption may occur upon application of direct water stream. Vapors are heavier than air and may travel a long distance and accumulate in low areas. Ignition and/or flash back may occur. Flammable mixtures may exist within the vapor space of containers at room temperature. Flammable concentrations of vapor can accumulate at temperatures above 74o F. Spills of these organic liquids on hot fibrous insulations may lead to lowering of the auto-ignition temperatures possibly resulting in spontaneous combustion.EXTINUISHING MEDIA:Water fog or fine spray, carbon dioxide, dry chemical, foam. Water fog, applied gently may be used as a blanket for fire extinguishments. General purpose synthetic foams (including AFFF type) or protein foams are preferred if available. Alcohol resistant foams (ATC type) may function. Do not use direct water stream, straight or direct water. Stream may not be effective to extinguish fire.MEDIA TO BE AVOIDED:Do not use direct water stream.FIRE FIGHTING INSTRUCTIONS:Keep people away. Isolate fire area and deny unnecessary entry. Burning liquids may be moved by flushing with water to protect personnel and minimize property damage. Water fog, applied gently may be used as a blanket for fire extinguishments. Eliminate ignition sources. Stay upwind. Keep out of low areas where gases (fumes) can accumulate. Do not use direct water stream. May spread fire. Water may not be effective in extinguishing fire. Move container from fire area if this is possible without hazard.PROTECTIVE EQUIPMENT FOR FIRE FIGHTERS:Wear positive-pressure self-contained breathing apparatus (SCBA) and protective fire fighting clothing (includes fire fighting helmet, coat, pants, boots, and gloves). If protective equipment is not available or not used, fight fire from a protected location or safe distance.SECTION VI - ACCIDENTAL RELEASE MEASURESPROTECT PEOPLE:Do not breathe vapors. Vapor explosion hazard, keep out of sewers. Eliminate all sources of ignition in vicinity of spill or released vapor to avoid fire or explosion. For large spills, warn public of downwind explosion hazard. Check area with explosion meter before reentering area. Ground and bond all containers and handling equipment.PROTECT THE ENVIRONMENT:For large spills, evacuate upwind of spills and contain with dike.CLEANUP:Pump with explosion-proof equipment. If available use foam to smother and suppress. Remove residual with hot soapy water. Residual can be removed with solvent. Solvents are not recommended for cleanup unless the recommended exposure guide-lines and safehandling practices for the specific solvent are followed. Consult appropriate solvent MSDS for handling information and exposure guidelines.STEP TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:Small Spill : Absorb liquid on paper, vermiculite, floor absorbent, or other absorbent material and transfer to hood.Large Spill : Eliminate all ignition sources (flares, flames, including pilot lights electrical sparks). Persons not wearing protective equipment should be exclude from area of spill until clean-up has been completed. Stop spill at source, dike area ofspill to prevent spreading, pump liquid to salvage tank. Remaining liquid may be taken up on sand, clay, earth, floorabsorbent or other absorbent material and shoveled into containers.WASTE DISPOSAL METHOD:Small Spill : Allow volatile portion to evaporate in hood. Allow sufficient time for vapor to completely clear hood duct work.Dispose of remaining material in accordance with applicable regulations.Large Spill : Destroy by liquid incineration in accordance with applicable regulation.Contaminated absorbent should be disposed of in accordance with government regulations.SECTION VII - HANDLING AND STORAGEHANDLING INFORMATION:Avoid inhalation and contact with eyes, skin, and clothing. Wash hands thoroughly after handling and before eating or drinking. Remove and wash contaminated clothing before reuse. Use with adequate ventilation. Ground and bond containers when transferring the material to prevent static electricity sparks which could ignite the vapor. Use spark-proof tools and explosion-proof equipment. Consult your supplier or promoters and catalysts for additional instructions on proper mixing and usage.Empty containers may retain product residue (liquid and/or vapor). Do not pressurize, cut, weld, braze, solder, drill, grind, or expose these containers to heat, flame, sparks, static electricity, or other sources of ignition as the container may explode and may cause injury or death. Empty drums should be completely drained and properly bunged. Empty drums should be promptly returned to a drum re-conditioner or properly disposed.STORAGE INFORMATION:Keep away from ignition sources; flames, pilot lights, electrical sparks, and sparking tools. NO SMOKING. Do not store in direct sunlight. Store separate from oxidizing materials, peroxides, and metal salts. Keep container closed when not in use. To ensure maximum stability and maintain optimum resin properties, resins should be stored in closed containers at temperatures below 75 degrees F (25 degrees C). Copper or copper containing alloys should be avoided as containers.SECTION VIII - EXPOSURE CONTROLS/PERSONAL PROTECTIONRESPIRATORY PROTECTION:If TLV of the product or any component is exceeded, a NIOSH/MSHA jointly approved air supplied respirator is advised in absence of proper environmental control. OSHA regulation also permit other NIOSH/MSHA respirators under specified conditions. (See your safety equipment supplier). Engineering or administrative controls should be implemented to reduce exposure. When respiratory protection is required, use an approved air purifying or positive-pressure supplied-air respirator depending on the potential airborne concentration.VENTILATION:Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below TLV(s).PROTECTIVE GLOVES:Wear resistant gloves such as: neoprene, nitrite rubber.EYE PROTECTION:Chemical splash goggles in compliance with OSHA regulations are advised; however, OSHA regulations also permit other type safety glasses (consult your safety equipment supplier).OTHER PROTECTIVE EQUIPMENT:Normal work clothing covering arms and legs.EXPOSURE GUIDELINE(S):Styrene, monomer: ACGIH TLV is 20ppm TWA, 40 ppm STEL, skin. ACGIH classifies as A4. OSHA PEL is 50 ppm TWA, 100 ppm STEL. The styrene PEL and STEL are in accordance with the OSHA-industry agreement dated March, 1996.SECTION IX - PHYSICAL AND CHEMICAL PROPERTIESProperties MeasurementInitial Boiling Point For Styrene 293.4o F/@ 760.0 mmHgVapor Pressure For Styrene 4.3 mmHg / 25o CVapor Density Air=1 3.6Specific Gravity 1.04 +/- 0.02 / 25o CPercent Non-volatile 55 +/- 2Evaporation Rate Slow than EtherSECTION X - STABILITY AND REACTIVITYHAZARDOUS POLYMERIZATION:May occur.STABILITY:Stable at room temperature.INCOMPATIBILITY:Strong alkalis, strong mineral acids and oxidizing agents.CONDITIONS TO AVOID:Exposure to excessive heat or direct sunshine or open flame; storage in open containers; storage above 38o C (100o F). Contamination with oxidizing agents.HAZARDOUS DECOMPOSITION PRODUCTS:Carbon Monoxide, Carbon Dioxide, Low Molecular Weight Hydrocarbon, Organic Acids.SECTION XI - TOXICOLOGICAL INFORMATION(See Section III for Potential Health Effects)SKIN CONTACT:The LD50 for skin absorption in rabbits is >2,000 mg/kg.INGESTION:The oral LD50 for rats is >4,000 mg/kgThe oral LC50 for rats is >5,000 ppm/4HMUTAGENICITY (EFFECTS ON GENETIC MATERIAL):For styrene: In vitro mutagenicity studies were inconclusive. Animal mutagenicity studies were inconclusive.SECTION XII - ECOLOGICAL INFORMATIONENVIRONMENTAL FATEMOVEMENT & PARTITIONING:Based on information for styrene. Bio-concentration potential is low (BCF less than 100 or Log Pow less than 3). Potential for mobility in soil is low (Koc between 500 and 2,000).DEGRADATION & PERSISTENCE: Based on information for styrene. Material is readily biodegradable. Passes OECD test(s) for ready biodegradability. Material is ultimately biodegradable. Reaches more than 70% mineralization in OECD test(s) for inherent biodegradability.ECOTOXICITY:Based on information for styrene. Material is highly toxic to aquatic organisms on an acute basis (LC50/EC50 between 0.1 and 1 mg/L in most sensitive species).SECTION XIII - DISPOSAL CONSIDERATIONS(See Section XV for Regulatory Information)DISPOSAL:DO NOT DUMP INTO ANY SEWERS, ON THE GROUND, OR INTO ANY BODY OF WATER. All disposal methods must be in compliance with all Federal, State/Provincial and local laws and regulations. Regulations may vary in different locations. Waste characterizations and compliance with applicable laws are the responsibility solely of the waste generator.SECTION XIV - TRANSPORT INFORMATIOND.O.T.: Bulk; ITAT: Non BulkProper Sipping Name: Resin SolutionHazard Class: 3ID: UN1866PG: IIIPlacard: FlammableEM Guidebook: 127SECTION XV - REGULATORY INFORMATION(Not meant to be all-inclusive--selected regulations represented)OSHA STATUS:This material is classified as a hazardous chemical under the criteria of the US Occupational Safety and Health Administration (OSHA) Hazard Communication Standard, 29 CFR 1910.1200.TSCA EXPORT NOTIFICATION:This material does not contain any components that are subject to the US Toxic Substances Control Act (TSCA) Section 12(b) Export Notification requirements.TSCA INVENTORY STATUS:All components of this material are listed on the US the Toxic Substances Control Act (TSCA) inventory.EUROPEAN/INTERNATIONAL REGULATIONS:European Labeling in Accordance with EC DirectivesHazard Symbols: XNRisk Phrases:FlammableR10:R 36/38: Irritating to eyes and skin.R 20: Harmful by inhalation.Safety Phrases:S 23: Do not inhale gas/fumes/vapor/spray.CALIFORNIA PROPOSITION 65:WARNING: This product contains a chemical(s) known to the State of California to cause cancer. Styrene Oxide.CAA:Styrene (100-42-5) is listed as a Hazardous Air Pollutant (HAP) under Section 112 of the Clean Air Act.CWA:Styrene (100-42-5) is listed under Section 311 as a Hazardous Substance.CANADA WHMIS:This material is classified by the Canadian Workplace Hazardous Material Information System as: B2 (flammable liquid) D2A (materials causing other toxic effects, very toxic material) D2B (materials causing other toxic effects, toxic material)CANADA CEPA:All components of this material are listed on the Canadian Domestic Substances List (DSL).ADDITIONAL CANADIAN REGULATORY INFORMATION:Under the Transportation of Dangerous Goods regulations, the following Chemicals have been assigned Regulated Limits (RL): Styrene Monomer (CAS # 100-42-5): RL=50 KG.The following chemicals are listed on the WHMIS Ingredient Disclosure List:Styrene Monomer (CAS # 100-42-5)The following chemical (s) are listed on the Canadian National Pollutant Release Inventory (NPRI):Styrene Monomer (CAS # 100-42-5)This material safety data sheet and the information it contains is offered to customers in good faith as accurate. We have reviewed any information contained in this data sheet which we received from sources outside our company. We believe that information to be correct but cannot guarantee its accuracy or completeness. Health and safety precautions in this data sheet may not be adequate for all individuals and/or situations. It is the user's obligation to evaluate and use this product safety and to comply with all applicable laws and regulations. No statement made in this data sheet shall be construed as a permission or recommendation for the use of any product in a manner that might infringe existing patents. No warranty is made, either express or implied.。

酚醛树脂(9003-35-4)化学品简介危险性概述急救措施Array消防措施泄漏应急处理操作处置与储存接触控制/个体防护理化特性稳定性和反应活性废弃处置运输信息化学品简介回目录【中文名称】酚醛树脂【英文名称】phenolic resin【中文同义词】苯酚树酯酚醛树脂苯酚与甲醛的聚合物酚醛树脂(热塑性)水溶性酚醛树脂直链酚醛树脂酚醛树脂(203型)松香改性酚醛树脂(2210型)酚醛模塑料(PF2C3-431J)酚醛模塑料(PF2C3-631)酚醛模塑粉(PF2A1-131F)快速模塑粉酚醛模塑料(PF2S1-4602)酚醛树脂(217型)电木粉R131胶木粉R131普通酚醛压塑粉(日用类,R131型)酚醛树脂(214型)酚醛模塑料(PF2A2-161J)PET改性酚醛树脂酚醛树脂(665型)电木粉D141【英文同义词】NOVOLAC COPOLYMER RESINPHENOL-FORMALDEHYDE RESINPhenolic resinRESOLERESOLE COPOLYMER RESINphenol,polymerwithformaldehydePhenol-formaldehydepolymerPhenol-formaldehydepolymerphenol-formaldehyderesinsPhenolicresin,thermoplasticresole(phenol-formaldehyderesin)【CAS No.】9003-35-4危险性概述回目录【健康危害】接触加工或使用本品过程中所形成的粉尘，可引起头痛、嗜睡、周身无力、呼吸道粘膜刺激症状、喘息性支气管炎和皮肤病，还可发生肾脏损害。

空气环境分析发现苯酚、甲醛和氨。

在缩聚过程中，可发生甲醛、酚、一氧化碳中毒。

【燃爆危险】本品易燃，具刺激性。

急救措施回目录【皮肤接触】脱去污染的衣着，用肥皂水和清水彻底冲洗皮肤。

【眼睛接触】提起眼睑，用流动清水或生理盐水冲洗。