管子轮机英语

【英语角】轮机英语词汇rotational speed：转速capacity: 功率steam turbine: 蒸汽轮机gas turbine: 燃气轮机speed reduction ratio: 减速比displacement: 排量flexible coupling: 柔性联轴节maintenance interval：检修周期gasoline engine：汽油机draft：吃水线torsional vibration damper: 减振器torque：扭矩prime mover：原动机be aligned with: 与…对中alignment：对中thermal efficiency：热效率loop scavenge：回流扫气cross scavenge：横流扫气uniflow scavenge：直流扫气supercharge：增压tappet clearance：挺杆间隙spark plug：火花塞indicator diagram：示功图indicator cards：示功图mechanical efficiency：机械效率compressed air: 压缩空气coolant：冷却剂occur：发生spray of fuel: 雾状燃油，油雾timing: 定时foul: 使…脏污fouling：污垢，脏污stuffing box：填料函，填料箱atmospheric pressure：大气压camshaft：凸轮轴cam：凸轮internal combustion engine：内燃机MIP（mean indicated pressure）：平均指示压力combustion chamber：燃烧室compression ratio：压缩比cylinder bore: 缸径overlap：重叠cross-head pin：十字头销bearing shell：轴瓦drill：钻孔，钻井，演习angle：角度expose：暴露，打开cycle：工作循环uncover：打开descending piston：下行的活塞value：值，数值decrease：降低，下降increase：上升，增加governor：调速器governor weight：调速器的飞重fuel injection：燃油喷射，喷油reliability：可靠性stroke coefficient：冲程系数give off：释放，放出naturally aspirated：自然吸气的，自然换气的admit：准许进入intake valve：进气阀linear motion：直线运动rotary motion：回转运动atomization：雾化cylinder firing pressure：气缸的爆炸压力be subjected to: 受到，遭受，承受ignition lag：滞燃期ignition delay period：滞燃期degree：程度，学位back pressure：背压thermal energy：热能mechanical energy: 机械能clockwise：顺时针地turbocharger：涡轮增压器brake horsepower：制动马力friction：摩擦single acting：单作用式的blow down：排气mixing：混合的mixture: 混合物advantage：优势，优点disadvantage：劣势，缺点compare：对比rocker arm：摇臂foundation：基础support：支撑，支持maintenance access：维修通道doors：道门in-line engine：直列式柴油机Vee engine：V型柴油机connecting rod large end bearing：连杆大端轴承connecting rod small end bearing：连杆小端轴承cast iron：铸铁cast steel：铸钢scavenging air box：扫气箱inertia：惯性thermal expansion：热膨胀aluminum：铝，铝的bronze：铜的mount：安装bolt：螺栓，用螺栓固定cross girder：横梁longitudinal girder：纵梁heat energy：热能float：漂浮，浮动piston skirt：活塞裙gudgeon pin：活塞销spur gear：正齿轮camshaft gear train：凸轮轴齿轮系starting air valve：空气启动阀side-chock bolt：侧楔形螺栓end-chock bolt：端楔形螺栓distance piece：调隙片compression plate：压缩片compression ratio：压缩比bearing housing：轴承座bearing cap：轴承盖bearing bush:轴瓦trunk piston：筒状活塞axial：轴向的stud：双头螺栓nut: 螺母enclose：密闭，密封guide：引导，导板tie rod=tie bolt=through bolt：贯穿螺栓entablature：机架column：机架cylinder block：气缸体external：外部的，外面的internal：内部的，里面的running-in period：磨合期load：负载，负荷，装载bearing wear：轴承磨损replace：替换，代替replacement：替换，代替clearance：间隙gap：间距tolerance：公差carrier ring：承磨环machine：机器，机械，加工machinery：机械（总称）machined：加工的，车削的ridge：凸台，凸肩groove：凹槽invariably：总是，一直forge：锻造forged：锻造的worn out：磨损的shim：垫片crank web：曲柄臂crank throw: 曲柄臂，曲拐crankpin：曲柄销crankcase：曲柄箱spring：弹簧，春天heat-resistant steel：耐热钢wearing resistance：抗磨，耐磨journal 轴颈sealing ring：密封环scraper ring：刮油环fuel valve：油头lubricator:注油器chromium-plated：镀铬的cylinder wall：汽缸壁lift out：吊出（活塞）piston ring belt: 活塞环区域cooling jacket：冷却水套balance：使…平衡shim：垫片thick：厚的thin：薄的thickness：厚度deformation：变形double bottom：双层底location：位置，定位locate：位于length: 长度width:宽度height：高度circular space：环形空间assemble：组装disassemble：拆卸assembly：组件fore and aft：前后semi-built：半组合式的transmit：传递，传送bending stress：弯曲应力torsion stress：扭曲应力shear stress：剪切应力turning gear：盘车机fitted bolt：拂配螺栓white metal：白合金horizontally：水平地be fitted with：装有，带有be provided with：装有，带有be equipped with装有，带有circumference [s?'k?mf?r?ns]: 圆周，周长nip：过盈压隙crush：过盈joint face：连接面，结合面diameter：直径oil distributor ring：布油环scraper ring：刮油环oil control ring：刮油环protective layer：保护层lining：衬有，内衬copper-lead alloy：铜铅合金aluminum-tin alloy：铝锡合金thin-walled：薄壁的flame hardened：淬火处理的shipchandler：船舶供应商bore：孔，镗孔thermal stress：热应力compressive stress：压应力forced lubrication system：强制润滑系统output：功率，输出cooling chamber：冷却腔crosshead shoes：十字头滑块slipper：滑块guide shoes：滑块dowel pin：定位销machine-turned：车削的projection：凸台vertical flange：垂直法兰coil spring：圈簧surface：表面slopping surface：倾斜表面sliding bearing：滑动轴承sludge：油渣main propulsion diesel engine：主推进柴油机tension：张力under tension：承受张力heater：加热器electric heater：电加热器timing gear：定时齿轮chain drives：链条驱动机构coincide with：重叠，一致center of gravity：重心statically balanced：静平衡wrist pin：活塞销heat conductivity：导热性oil film：油膜excess：过多的excessive：过多的，过大的rigid：结实的，坚实的transverse girder：横梁jack bolt：撑杆螺栓tap-bolt：锥头螺栓solid forged：整体锻造的solid bearing：整体式轴承polish：抛光telescopic pipe：伸缩管sag：下垂sagging：下沉量component：部件corrosion resistant：耐腐蚀的flame screen：防火网罩watertight compartment：水密舱taper：锥形的，逐渐减小的insert：插入：插件stationary part：固定部件statically balanced：静平衡dynamically balanced：动平衡turbulence：涡流flywheel：飞轮kinetic energy：动能fluctuation：波动valve stem：阀杆valve head：阀头valve cage：阀壳heat dissipation：散热water seal：水封wet liner：湿式缸套dry liner：干式缸套test cock：示功考克gasket：垫片knurling：滚花sodium：钠cold clearance：冷态间隙thrust：推力side thrust：侧推力manifold：总管bundle：管束overload：过载plasma coated：等离子涂层的oil sump：油底壳treat：处理，对待treatment：处理advanced firing：早燃retarded firing：后燃，发火滞后air venting arrangement：放气装置prime：灌注，注油priming：灌注priming pump：引液泵fuel supply passage：供油管路viscosity regulator：粘度调节器lifting check：起阀压力试验fuel main：总管plunger：柱塞spindle：针阀available：可用的，可得到的manoeuvring condition：机动操纵状态specification：规格grade:规格specific gravity：比重specify：规定service tank：日用柜day tank：日用柜port：港口，开口pressurize：加压injector nozzle：喷油嘴clog：堵塞particle：颗粒，颗粒状index：刻度，指数reading：读数rack：齿条rack and pinion arrangement：齿条/齿轮装置transfer pump：驳运泵bunker tank：燃油舱banker list：加油单have much to do with：与…..有很大的关系have nothing to do with：与…..没有关系quality：质量quantity：数量earlier ignition：发火提早stick open：保持开启状态oil sump：油底壳settling tank：沉淀柜droplet：水珠，油滴strainer：粗滤器fine filter：细滤器at interval：定期地prevent from doing sth.:防止做某事set：设定setting：设定量，设定值preset：预先设定buffer tank：缓冲柜balance tank：平衡柜（集油柜）service tank：日用柜cleared of：排除，清除barrel：套筒sleeve：套筒pipe：管子duct：管道，导管hose：软管flash point：闪点overflow：溢出（满了溢出）spill：溢油full ahead：全速前进fuel consumption：燃油消耗save：挽救，救生，节省economical speed：经济转速purify：分离，清洁purifier：分水机clarifier：分杂机foreign matter：杂质follower：滚轮calorific value：发热值pour point：倾点diameter：直径original：原来的，开始的vibration：振动penetration of fuel：燃油穿透penetration：穿透力distribution of fuel：燃油分布minimize：使….最小化maximize：使…..最大化shut down：关闭，切断cut off：终止，关闭check valve：止回阀jerk pump：喷射泵meter：计量，测量，米proper metering：精确计量parameter：参数size：尺寸carbon accumulation：结炭flow rate：流速break up：分裂，破裂，分手manufacture：制造商precaution：预防措施contamination：污染，脏污cetane rating：十六烷值cetane number：十六烷值secure the fuel supply：切断燃油供应take place：发生，开始commence：发生，开始slope：斜面spill port：回流孔，溢流孔build up：建立，积聚helix：螺旋槽MCR：最大持续功率base circle：基圆sulfur：硫water vapor：水蒸汽acid：酸，酸的malfunction：故障ash：灰duplex pressure gage：双联压力表thermostatic：恒温的needle valve：针阀differential needle valve：差压式针阀constant volume：定容constant pressure：定压unit injector：单体式喷油器misfiring：不发火vanadium：钒sodium：钠indicate：显示，表示contribute to：有利于，导致block：堵塞compressibility:压缩性remove：清除，去除sounding tube：深管sounding rod：量油杆oil impingement：注油cavitation （erosion）:气穴，汽蚀booster pump：增压泵 salt water：海水raw water：海水air cooler：空冷器make up：补充，补给distilled water：蒸馏水in contact with：与….接触facilitate：有利于，促进prior to：在….之前acid solution strength：酸性强度lime：石灰，氧化钙get rid of：去除，排除，摆脱release：释放mechanical property：机械性能expansion tank：膨胀水箱head tank：高置（膨胀）水箱coolant：冷却剂inoperative：不运转的，不运行的frost：结霜individual：单独的，独立的deposit：沉积物，沉淀物scale：水垢rust：生锈，铁锈dividing wall：分隔板overheat：过热explosion：爆炸chemical addition：投药，添加化学品additive：添加剂steam coil：蒸汽盘管anti-corrosion oil：防锈油inorganic inhibitor：无机缓蚀剂corrosion inhibitor：抗腐蚀剂regulate：调节modulate：调节head：压头volume：体积，容积closed cooling system：闭式冷却系统a portion of：一部分heat exchanger：换热器slightly：轻微的，轻度的nozzle holder：喷嘴座crack：裂纹suspect：怀疑baffle plate：挡板sacrificial zinc：保护性锌块soluble oil：可溶性油thermometer：温度计obstruct：堵塞，阻塞impeller：叶轮fin：翅片alarm：报警，警报器activate：激发，动作housing：壳体concentric：同心的bi-directional operation：双向运行compensating tank：补偿水箱（膨胀水箱）salinity：盐分，盐度alternative：选择，替代deaerating tank：除气柜three-way valve：三通阀flush：吹洗，冲洗oil barge：油驳interlocking device：连锁装置reversing：换向pilot air：控制空气，先导空气air distributor：空气分配器fusible plug：易熔塞guard against：防止air reservoir=air bottle=air receiver：空气瓶pneumatic control system：气动控制系统pneumatic tool：气动工具drain cock：放残考克blade：叶片turbine：透平remote valve：遥控阀air startlever：空气启动手柄instrument：仪表humidity：水分starting air distributor：启动空气分配器sufficient：充足的，足够的consecutive start：连续启动knocking sound：敲缸condensate：凝水condensation：冷凝run roughly：运转不平稳delay：推迟，延迟clearance volume：余隙容积two stage compressor：两级空气压缩机intercooler：中间冷却器，中冷器aftercooler：后冷器airborne：空气中携带的valve plate:阀片valve strip：阀片valve face：阀面valve seat：阀座volumetric efficiency：容积效率LP cylinder：低压缸HP cylinder：高压缸trip：跳闸overload relay：过载继电器dew point：露点splash lubrication：飞溅润滑water hammer：水击air delivery line：排出管路non-return valve：止回阀，单向阀carbonization：碳化throttling：节流solenoid：电磁的idle speed：怠速storage tank：储存柜neutralize：中和neutralization number：中和值alkalinity：碱detergency：清洁剂fundamental：基本的guard against：防止stern-tube bearing：尾轴承lignum vitae：铁梨木emulsion oil：乳化油，乳化防锈油sodium nitrite：硝酸钠additive：添加剂approved：认可的galvanize：镀锌investigation：调查gas seal 气封pot-shaped piston：筒状活塞analyze：分析total loss system：全消耗系统recirculation system：循环系统renew：更新，换新renewal：更新，换新static head：静压头in duplicate：一式两份，一式两台carry away：带走magnetic filter：磁性滤器blow out：吹洗in that：在于，因为former：前者latter：后者forced lubrication system：强制润滑系统employ：采用，使用，利用，雇佣hydrostatic lubrication：液体静力润滑impurity：杂质to a great extent：在很大程度上deterioration：恶化heat transfer：传热wear detritus：磨屑trouble-free life：无故障寿命dilute：冲淡，稀释，降低mist detector：油雾检测器monitor：检测，监控duplex filter：双联式滤器audible/visual alarm：声光报警shaker：振荡scuffing：划伤remain：保持remaining：剩余的retain：保留clogged：堵塞的hard varnish：硬的清漆pitting：点蚀oxidize：氧化carbon deposit：积碳detergent oil：净化油orifice：油孔diffuser：扩压器constant-pressure：定压增压pulse pressure：脉冲增压angle：角度，成….角度smoky exhaust：排气冒黑烟opposite：相反的，相对的supercharging：增压make use of：利用blower：鼓风机turboblower：涡轮增压器adjacent：相邻的in comparison to：与…相比compared to：与…相比fabricated：锻造的swirl：旋转rated speed：额定速度rated load：额定负载oxygen：氧气oxidize：使…氧化average：平均的velocity：速度directly proportional to：成正比characteristic：特点in conjunction with：和….一起performance：性能utilize：利用，使用furnish：提供muffle：消音，降低gas exchange：换气lose power：损失功率loss of pressure：失压take out=disengage:脱开put in=engage：合上FWE=finished with engine：完车give a trial：试车ahead and astern: 正倒车packing box：填料箱overhaul：大修stall：停止，停车enlarge：扩大，变大abnormal：不正常on no account：绝不，不可以seizure：卡住，咬缸gradually：逐渐地，逐步地remedy：补救，补修metalock：金属扣合法warm up:加温，暖机unless：除非surge：喘振spark：火星paint：油漆blistering：起泡peeling：剥落withdraw：取出routine 日常的，周期性的whilst=while：当…时候eliminate：消除，清除ambient temperature：环境温度regarding：关于with regard to：关于，对于….来说ventilation：通风vacuum：真空risk：风险，危险hazard：危险head wind：顶风heavy sea：风浪大combustion knock：燃烧过程粗暴wheelhouse：驾驶台contaminant：杂质，污染物cease：停止defect：损坏，缺陷sensor：传感器dead slow ahead：微速前进distribution：分配，布置，配电idle：闲置的guarantee：保证，确保pressure-volume diagram：压容图jerk pump：脉动泵，急拉式泵by-product：副产品erosion：剥蚀spark arrestor：火花消除器navigation：航行score：划痕scratch：刮痕abrasive particle：磨蚀颗粒pyrometer：高温计（测量排烟温度）manometer：压力计pressure gauge：压力表dial indicator：千分表，量缸表micrometer：千分表feeler：塞尺straight edge：直尺bridge gauge：桥规（轴颈下沉量，较小的主轴承磨损）blow-by：漏气break-in period：磨合期hone：搪磨detuner：减震器verify：检查，证实underway：航行时at partial load：部分负载localized：局部的local：当地的，机旁的file：锉blank off：堵死rotor：转子metal scraper：金属刮刀wrench：扳手moisture：水分muffler=silencer：消音器switch on：接通absolute pressure：绝对压力（=表压力+大气压力）air blast pump：抽气泵quay：码头direction handle：换向手柄coke deposit：积碳asphalt：沥青boss：桨毂hub：桨毂，轮毂variable pitch propeller：调距桨controllable pitch propeller：调距桨constant pitch propeller：定距桨fixed pitch propeller：定距桨tail shaft：尾轴intermediate shaft、；中间轴mass：重量in turn：依次，循序thrust block：推力块thrust pad：推力块reversing gear：换向装置axial movement：轴向运动solid propeller：整体式螺旋桨stem：船尾astern：船尾bow：艏，船头apparent slip：滑失比helix：螺旋线helicoidal：螺旋面，螺旋状的uniform pitch：定螺距non-uniform pitch：不定螺距pitch ratio：螺距比rubber：橡胶sterntube bearing：尾轴管轴承common rail system：共轨燃油系统VIT= variable injection timing: 可喷油定时森海海事服务。

一．职位及工种(Titles and type of work) 1．船长 Captain 2．大副 Chief officer 3．二副 Second officer 4．三副 Third officer 5．四副 Fourth officer 6．水手长 Boatswain 7．水手 Sailor & Seaman 8．木匠 Carpenter 9．轮机长 Chief engineer 10．大管轮 Second engineer 11．二管轮 Third engineer 12．三管轮 Fourth engineer 13．机匠长 Chief motorman 15．机匠 Fitter 16．加油工 Oil man 17．大电 Chief electrician 18．电工 Electrician 19．车间主任 Workshop director 20．工长 Section chief 21．班长 Fore man22．钳工 23．主管工程师 Engineer in charge24．机务&船东 Superintendent &Super &Owner 25．助理工程师 Assistant engineer 26．验船师（机）Register 27．验船师（船）Surveyor 28．油漆工 Painter 29．焊工 Welder 30．大橱 Chief cook 31．物料员 Store keeper 32．加油工 Oiler33．机工 Mechanic 34．甲板员 Deck man 35．电线工 Wireman 36．外包工 Laborer 37．铸工 Molder 38．管子工 Pipe fitter 39．起重工 Crane operator二、柴油机类1．主机 2．二冲程柴油机 3．四冲程柴油机 Fore-stroke diesel engine4．高速柴油机 High speed diesel engine 5．中速柴油机 Middle speed diesel engine 6．低速柴油机 Low speed diesel engine 7．气缸盖(缸头) Cylinder head 8．安全阀 Safety valve 9．释放阀 Relief valve 10．示功阀 Indicator valve 11．示功考克 Indicator cock 12．空气起动阀 Air starting valve13．起动空气分配器 Air starting distributor 14．油头(燃油喷射器) Fuel injector 15．排气阀 Exhaust valve 16．气缸套 Cylinder liner17．冷却水套 Cooling water jacket 18．气缸注油器 Cylinder lubricator 19．活塞 Piston20．活塞头 Piston crown 21．活塞裙 22．活塞销 24．活塞杆 25．活塞环 Piston ring26．活塞环槽 Piston ring groove 27．压缩环 (气环) Compression ring 28．刮油环 (油环) Oil scraper ring29．减磨令 Wear ring (copper ring) 30．伸缩管(水拉管) Telescopic pipe31．活塞冷却空间 Piston cooling space 32．填料箱(函) Stuffing box33．填料箱密封环Sealing ring for Stuffing box 34．填料箱压缩环 Pressure ring for Stuffing box 35．填料箱刮油环 Scraper ring for Stuffing box 36．扫气箱 Scavenging receiver 37．扫气口 Scavenging port 38．排气口 Exhaust port 39．十字头 Cross head 40．十字头销 Crosshead pin 41．十字头轴承 Crosshead bearing 42．十字头滑块 Crosshead slipper 43．滑块 44．十字头导板 45．连杆 46．连杆大端轴承 47．连杆小端轴承 Small end bearing 48．曲柄轴承 Crank bearing 49．曲柄销 Crank pin 50．曲轴 Crank shaft 51．曲轴颈 Crank journal 52．曲柄臂 Crank web53．拐档差Crank deflection54．主轴承Main bearing55．主轴颈Main journal56．轴承瓦Bearing bush57．上轴瓦Upper bearing bush58．上轴瓦Upper half59．下轴瓦Lower bearing bush60．下轴瓦Lower half61．推力轴承Thrust bearing62．推力块Thrust pad63．推力盘Thrust disc64．推力轴Thrust shaft65．底座Bed plate66．机架67．曲柄箱68．曲柄箱导门69．曲柄箱防爆门Explosion-proof Crank case.70．定时齿轮Timing gear71．飞轮Flying wheel72．凸轮Cam73．凸轮轴Cam shaft74．喷油凸轮Fuel injection cam75．链条Chain76．链条轮Chain wheel77．链条箱Chain box78．推杆Push rod79．摇臂Rocker arm80．排气阀Exhaust valve81．吸气阀Suction valve82．排气总管Exhaust manifold83．进气总管Air inlet manifold84．高压燃油管High pressure fuel pipe85．活塞冷却水管Piston cooling water pipe86．法兰Flange87．贯穿螺栓Tie bolt (tie rod)88．端盖89．滑油泵90．燃油泵91．滑油泵齿轮Gear for lubricating oil pump92．燃油泵齿轮Gear for fuel oil pump93．叶轮Impeller94．柱塞Plunger95．导杆Guide rod96．导套Sleeve97．滚动轴承Ball bearing98．滑动轴承Sliding bearing99．推力滚动轴承Thrust ball bearing100．推力面Thrust surface (thrust side)101．盘车机Turning gear102．增压器Turbocharger103．涡轮机(透平)Turbine104．涡轮Turbine wheel105．涡轮叶片Turbine blade106．喷嘴Nozzle107．废气叶轮Exhaust impeller108．废气叶轮片Exhaust blade109．废气端Exhaust side110．透平端111．转子轴112．油泵113．换向装置Reversing device114．换向伺服期Reversing servomotor115．压气机(鼓风机) Blower116．膨胀接Expansion joint117．调速器governor118．飞重Flying weight119．补偿阀Compensate valve120．针阀Needle valve121．开口销Cotter pin122．轴封Shaft seal123．机械密封Machinery seal124．配电盘Switchboard125．应急配电盘Emergency switchboard126．应急发电机Emergency generator127．滤器Filter128．细滤器Filter129．粗滤器Strainer130．滑油滤器L.O. filter131．燃油滤器 F.O. filter132132．空气滤器133．空气瓶134．分油机Separator135．油水分离器Water-oil separator136．净油机Purifier137．燃油净化器 F.O. purifier138．二氧化碳CO2139．二氧化碳瓶CO2 bottle140．正时齿轮Timing gear141．导向棒装置Guide bar142．注油器驱动Lubricator driver143．链条张紧装置Chain tightener144．凸轮轴传动轮Chain wheel on cam shaft145．中间链链传动轮Intermediate chain wheel146．注油器驱动装置Lubricator drive147．链条张紧装置Chain tightener148．滚筒导座Roller guide housing149．应急操纵台Emergency console150．力矩平衡器151．主启动阀152153．喷油器Fuel valve154．扫气系统Scavenge air system155．安全帽Safety cap156．机座Bed plate157．轴向振动减振器Axial vibration damper158．贯穿螺栓Arrangement of stay bolt159．示功器驱动装置Indicator driver160．端罩End shields161．气缸架Cylinder frame162．气阀传动装置Valve operating device163．摇臂润滑油泵Rocker arm lubricating oilpump164．摇臂润滑油柜Rocker arm lubricating tank165．摇臂润滑滤器Rocker arm lubricating filter三、船舶机械类1．船用锅炉2．废气锅炉3．辅锅炉Donkey boiler4．组合式锅炉Combined boiler5．火管Fire tube6．给水管Feed pipe7．炉膛Furnace8．炉墙Furnace wall9．火侧Fire side10．水侧Water side11．燃烧器Oil burner12．安全阀Safety valve13．上排污Upper drain14．下排污Lower drain15．锅炉皮阀Mounting valve16．水位计Water level gauge17．压力表Pressure gauge18．主汽门Main steam valve19．玻璃管Glass tube20．空调装置Air-conditioning plant21．制冷装置Refrigerating plant22．冰机Fridge. Machine23．空气压缩机Air compressor24．造水机Fresh water generator25．板式冷却器Plate type cooler26．机舱天车Engine room crane27．天车导轨Crane rail28．电磁阀Solenoid valve29．舵机Steering gear30．舵承Rudder bearing carrier31．液压缸Hydraulic cylinder32．废气涡轮增压器Exhaust gas turbocharger33．弹簧阀Spring loaded valve34．冷凝器Condenser35．分油器Oil separator36．轴带发电机Shaft generator37．焚烧炉Oil burner38．分油机Separator39．分离筒Separator bowl40．配水盘装置Paring disc device41．转数计Revolution counter42．控制阀Control valve43．辅机44．制冷装置45．海水淡化装置Sea water desalting plant46．热交换器Heat exchanger47．船用气瓶Marine air bottle48．冷风机Cooler unit49．防水风门Fire damper50．气密挡板Gas tight damper51．排气风机Exhaust fan52．舱室通风机Cabin fan53．机舱通风机Engine room fan54．应急鼓风机Emergency blower四、阀门1．吸气阀2．排气阀Exhaust valve3．控制阀Control valve4．导阀Pilot valve5．单向阀Non-return valve6．口琴阀Flap valve7．调节阀Regulating valve8．液压阀Hydraulic valve9．膨胀阀Expansion valve10．给水阀Feed valve11．排水阀Discharge valve12．截止阀Stop valve13．吹泄阀Blow-off valve14．空气阀Air valve15．泄放阀Drain valve16．止回阀Check valve17．海底阀Sea valve18．回流阀Retune valve19．节流阀Throttle valve20．进气阀Inlet valve21．出气阀Outlet valve22．热力阀23．中央阀24．单向阀25．二通阀Two way valve26．三通阀Triple valve27．旁通阀By-pass valve28．换向阀Change-over valve29．减压阀Pressure-reducing valve30．溢流阀Overflow valve31．自闭阀Self-locking valve32．针阀Needle valve33．平衡阀Balance valve34．循环阀Circulation valve35．主阀Main valve36．滑阀Slide valve37．蝶阀Butter-fly valve38．截止阀Shut-off valve39．闸板阀Gate valve40．通海阀Sea suction valve41．吹除阀Sea chest cleaning valve42．防浪阀Storm valve43．舱壁阀Bulkhead valve44．快关阀Emergency shut off valve45．呼吸阀Breather valve五、泵类1．电动泵2．柱塞泵3．叶片泵Vane pump4．回转泵Rotary pump5．齿轮泵Gear pump6．往复泵Reciprocating pump7．离心泵Centrifugal pump1．电动泵Motor-driven pump2．柱塞泵Plunger pump3．叶片泵Vane pump4．回转泵Rotary pump5．齿轮泵Gear pump6．往复泵Reciprocating pump7．离心泵Centrifugal pump8．真空泵Vacuum pump9．螺杆泵Screw pump10．喷射泵Ejector pump11．冷却泵Cooling pump12．淡水泵Fresh water pump13．海水泵Sea water pump14．给水泵Feed water pump15．循环泵Circulating pump16．锅炉给水泵Boiler feed pump1718．压载泵19．舱底泵20．污水泵21．燃油泵Fuel pump22．高压油泵High pressure pump23．底压油泵Low pressure pump24．驳运泵Transfer pump25．增压泵Booster pump26．消防泵Fire pump27．通用泵G.S. pump28．旋涡泵Regenerative29．蜗壳泵V olute pump30．导叶泵Diffuser pump31．单联泵Simplex pump32．双联泵Duplex pump33．多联泵Multiplex pump34．活塞泵Piston pump35．减摇泵Anti-roll pump36．总用泵General service pump37．应急消防泵Emergency fire pump38．扫舱泵Stripping pump39．货油泵Cargo oil pump40．滑油泵Lubricating oil pump）1．锚机2．锚机轴Windlass shaft3．刹车带Brake lining4．离合器Clutch5．锚链轮Anchor Chain wheel6．轴承瓦Bearing bush7．轴承盖Bearing cover8．绞揽机Capstan9．系揽绞车Mooring winch10．卷缆车Reel11．钢丝绳Wire rope12．卡环Shackle13．缆绳Mooring rope14．滑轮Block15．刹车装置Brake device16．制链器Anchor chain stopper17．舱盖滚轮Hatch cover wheel18．舱盖铰链Hatch cover hinge19．液压油缸Hydraulic jack20．起货机Cargo winch21．可令吊Crane22．生活吊23．吊杆24．桅杆Mast25．救生艇Lifeboat26．艇架Davit27．艇机Lifeboat capstan28．救生筏Life raft29．救生衣Life jacket1．车床2．刨床3．钻床Drill machine4．砂轮机Grinding machine5．磨床Grinder6．铣床Milling machine7．镗床Boring machine8．手锤Engineer’s hammer9．冲击板手Impact wrench10．板手Spanner11．活络板手Screw spanner12．梅花板手Ring spanner13．呆扳手Open spanner15．套筒板手Socket spanner16．管子钳Pipe spanner17．螺丝刀Screw driver18．钢丝钳Wire pliers19．尖嘴钳Long nose pliers20．钢锯Hack saw21．剪刀Scissors22．手电筒Torch23．扁铲(凿子)24．锉刀File25．丝攻26．板牙Thread die27．绞刀Reamer28．刮刀Scraper29．油石Oil stone30．拔子(拉马) Puller31．沙布Emery cloth32．破布Rag33．卷尺Measuring tape34．空心冲Hole punch35．样冲Joint punch36．油壶Oil gun37．牛油枪Grease gun38．手电钻Handle drill39．钻头Drill40．液压千斤Hydraulic jack.41．塞尺Feeler gauge42．游标卡尺Vernier caliper43．外卡尺Outside calipers44．内卡尺Inside calipers4546．桥规47．电焊机48．气焊机Gas welding machine49．电焊钳Electric welding pliers50．气割枪Cutting touch51．电焊条Electric soldering iron52．电工刀Electrician knife53．电笔Test pen54．剥线钳Wire stripping pliers55．圆规Compass56．量表Gauge57．拐档表Crank deflection gauge58．深度规Depth gauge59．千分表Micrometer gauge60．台虎钳Table vice61．柴油Diesel oil62．滑油Lubricating oil63．液压油Hydraulic oil64．重油Heavy oil65．燃油Fuel oil66．黄油Grease67．螺栓Bolt68．螺帽Nut69．垫片Washer70．研磨沙 Grinding sand 71．研磨膏 Grinding paste 72．石棉板 Asbestos plate 73．青壳纸 Fish paper 74．盘根 Packing75．细钢丝 Thin steel wire 76．密封圈 Rubber seal ring 77．塑料管 Plastic pipe 78．胶皮管 Rubber hose 79．电灯泡 Electric bulb 80．工作灯 Working lamp 81．插头 Electric plug 82．插座 Electric socket.93． 喷砂机 Sand blaster outfit 94． 空气马达 Air motor95．油柜清洁器 Tank cleaning machine 96．高压冲水机 High pressure hose for hydraulic 97．真空泵 Vacuum pump 98．套筒扳手组 Socket wrench set 99． 深头套筒100．套筒扳手101．单开口扳手 102．双开口扳手 Double open end wrench 103．转矩扳手 Torque wrench 104．电动机扳手 Motor wrench 105．侧剪钳 Slide cutting plier 106．活节钳 Combination plier 107．可调快速扳手Speed wrench 108．螺丝起子 Screwdriver 109．偏向螺丝起子Offset screw110．六角螺帽起子组Hexagon nut drivers set 111．手摇钻 Straight hand drill 112．手工锯 Hacksaw frame 113．锯片 Hacksaw blade 114．砂纸 Silicon paper 115．手拉葫芦 Chain block116．高压管 High pressure hose 117．液压千金顶 Hydraulic jack 118．锤子 Hammer 119．平錾 Cold chisel120．活动扳手 Adjustable wrench 121．螺丝刀122．侧剪铗123．螺栓剪 124．敲击管钳 Rap wrench 125．砂轮 Grinding wheel 126．老虎钳 Utility vise 127．直梯 Straight ladder 128．踏梯 Step ladder 129．平台推车 Platform trunk130．搬平车 Gas cylinder carrier 131．给油机 Grease lubricator132．强力油泵 Heavy duty pump oiler 133．油壶 Oil jag 134．麻花钻 Twist drill 135．绞刀 Pin reamer 136．旋转中心钻Rolling center137．外径测微计Outside micrometer with counter 138．六折式尺 Six-folding rule 139．弹性带尺 Convex rule140．不锈钢直尺 Stainless steel straight rule 141．平面规 Surface gauge142．平行直角定规Precision flat try square 143．温度计 Thermometer八、常用物料1．阀研磨剂 2．电焊条 steel electrode 3．气焊条 Steel welding wire 4．细钢丝绳 Seizing wire 5．刚焊条 Steel welding rod 6．紫铜管 Copper tube7．乙炔气瓶 Acetylene cylinder 8．木屑 Saw dust 9．水泥 Cement 10．石灰 Lime11．帆布手套 Canvas glove 12．垫片 Gasket.13．氧气瓶 Oxygen cylinder 14．抹布 Rag 15．垫隙片 Shim 16．电线 Wire17．电缆 Electric cylinder 18．电池 Rag 19．灯泡 Bulb20．胶布 Insulating tape 21．插头 Plug 22．插座 Socket 23．保险丝 Fuse24．不锈钢 25．铸铁 26．黄铜 27．青铜 Bronze28．铝合金 Aluminium alloy 29．橡胶 Rubber 30．石棉 Asbestus 31．低碳钢 Soft steel32．高碳钢 High-carbon steel 33．合金钢 Alloy steel 34．木材 Wood 35．塑料 Plastic36．球墨铸铁 Nodular iron九、常用紧固件in commonuse)1．螺栓Bolt2．螺丝Screw3．螺母Nut4．方头螺栓Sq head bolt5．埋头螺栓Counter sunk head screw6．套筒螺栓Socket head bolt7．定位螺栓Set screw8．十字接头Cross9．锥形销Taper pin10．锁紧螺母Lock nut11．六角头螺栓Hex head bolt十、常用油类(Oil in common use)1．汽油Gas oil2．煤油Kerosene3．润滑油Lubricating oil4．汽缸油Cylinder oil5．压缩机油Compressor oil6．齿轮油Gear oil7．机油Motor oil8．凡士林Vaseline9．燃油Fuel oil10．油脂Grease11．柴油十一、常用量词1．件，只，个2．条，张，片Sheet3．双Pair4．套，组，副Set.5．盒Box6．箱Case7．瓶Bottle8．米Meter9．厘米Centimeter10．毫米Millimeter11．公斤Kilogram12．克Gram13．公升Liter14．平方Square15．袋Bag16．码Yard17．吨Ton18．磅Pound19．加仑Gallon20．立方Cubic十二、国家名称1．中国China2．美国3．日本Japan4．英国Britain5．法国France6．德国German7．韩国South Korea8．希腊Greece9．泰国Thailand10．印度India11．挪威Norway12．俄罗斯Russia13．新加坡Singapore14．澳大利亚Australia15．伊朗Iran16．丹麦Denmark17．加拿大Canada18．丹麦Denmark19．芬兰Finland20．巴基斯坦Pakistan21．意大利Italy1M/E2A/E3．阀V/V4．泵P/P5．备车St/by6．完车 F.W.E.7．前进三FAHD8．微速后退 D.S.Ast9．前进二H.Ahd10．高压H.P.11．低压L.P.12．重油/柴油H.O./D.O.13．前后F/A14．左舷P: port15．无人机舱UMS16．自动Auto17．气缸Cyl18．燃油柜 19．滑油柜20．沉淀柜.21．排出Disc22．吸入Suct23．柴油柜 1．停靠2．接近3．停泊Berth4．浮筒Buoy5．码头Pier6．港口Port7．移泊Shift8．航次V oyage9．试验Try10．值班Watch11．航行Sail1．调整2．压载Ballast3．转换Change over4．清洁Clean5．联接Connect6．排放压载Deballast7．放残水Drain8．卸载Off9．油漆Paint10．接通Put on11．吹灰Soot blown12．开始Start13．顶端Top14．洗Wash15．吹Blow16．检查Check17．铲Chip18．断开Cut out19．排放Discharge20．除垢Descale21Examine22On(load)23Pump out24．调整Set25．停止Stop26．调驳Transfer27．加满Top up十六、故障常用单词1．失常的2．烧坏Burn3．堵塞Clog4．裂缝Crack5．变形Deform6．毁坏Destroy7．磨损Wear8．出故障In trouble9．敲击Knock10．松开Loose11．不对中Misalign12．不足的Insufficient13．失灵Out of order14．过载Overload15．过度磨损Over-worn16．尺寸过大Oversized17．尺寸过小Under-sized18．振动Vibrate19．不平的Uneven20．不准确Inaccurate21．全船断电Black out22．出故障23．关掉24．弯曲25．停车Break drown26．腐蚀Corrode27．腐蚀的Corrosive28．损坏Damage29．有毛病的Faulty30．有缺陷的 Defective 31．破裂 Fracture 32．卡住 Jam 33．漏泄 Leak 34．漏泄的 Leaky 35．融化 Melt 36．噪声 Noise 37．过热 Overheat 38．咬住 Seize 39．紧的 Tight 40．松的 Loosen 41．发现 Find 42．停止 Stop43．脏的 Dirty 44．油污的 45．失效的 46．椭圆形的 47．点不着火 misfire 48．接错 misjoin49．放错 misplace 50．老化 perish 51．麻点 pit 52．凸起 ridge53．划伤 score 54．拉痕 scuff1．卡死 Blind2．用卡钳量 Caliper 3．关闭 Close 4．解体 Disassemble 5．安装 Fix 6．组装 Box up 7．检验 Check 8．拆卸 Dismantle 9．装配 Fit 10．紧固 Fasten 11．测量 Gauge12．安装 Install 13．测量 Measure 14．打开 Open 15．上油漆 Paint 16．换新 Renew 17．上紧 Tighten 18．洗 Wash 19．涂油脂 Grease 20．松开 Loosen 21．加油 22．检修23．重新组装 Reassemble 24．测取读数 Take reading 25．拧开螺栓 Unbolt 26．抽出 Withdraw十八、常用数字一 One 二 Two三 Three 四 Four 五 Five 六 Six 七 Seven 八 Eight 九 Nine 十 Ten 十一 Eleven 十二 Twelve 十三 Thirteen 十四 Fourteen 十五 Fifteen 十六 Sixteen 十七 Seventeen 十八 Eighteen十九Nineteen二十Twenty三十Thirty四十Forty五十Fifty六十Sixty七十Seventy八十Eighty九十Ninety百Hundred千Thousand万Ten thousand百万Million第一First第二Second第三Third第四Fourth第五Fifth第六Sixth第七Seventh第八Eighth第九Ninth第十Tenth第十一Eleventh第十二Twelfth第二十Twentieth(Time、1．星期一Monday2．星期二Tuesday3．星期三Wednesday4．星期四Thursday5．星期五Friday6．星期六Saturday7．星期日Sunday8．春季Spring9．夏季Summer10．秋季Autumn11．冬季Winter12．一月January13．二月February14．三月March15．四月April16．五月May17．六月June18．七月July19．八月August20．九月September21．十月22．十一月November23．十二月December24．小时Hour25．分钟Minute26．秒Second27．月Month28．天Day29．夜Night30．周Week31．早晨、上午Morning32．下午Afternoon33．傍晚Evening34．正午Noon35．今天Today36．昨天Yesterday37．明天Tomorrow38．前天The day before yesterday39．后天The day after tomorrow40．本周This week41．上周Last week42．下周Next week43．九月十日44．去年45．明年Next year46．上周二Last Tuesday47．下周一Next Monday48．东East49．西West50．南South51．北North52．西北Northwest53．东北Northeast54．东南Southeast55．西南Southwest56．世纪Century）1found beyond repair2．发现尺寸过大found over-sized3．发现反应缓慢found slow function4．发现不正常found out of order5．发现不合标准found not up to standard6．发现不准确 found inaccurate 7．发现失去作用 found out of function 8．发现轧住 found seized 9．发现过热 found overheated 10．发现过度磨损 found excessive wear 11．发现过度磨掉 found worn out12．发现有一点倾斜 found a little bit inclined 13．发现不正常 found abnormal14． 发现因过热而损坏found destroyed byoverheating15．发现龟裂 found chapped 16．发现塌陷 found collapsed17．发现运转失灵 found out of operation 18．发现呈椭圆形 found oval 19．发现拉痕 found scored 20．发现拉毛 found scuffed 21．发现变形 22．发现松动 23．发现油污 found greasy 24．发现肮脏 found dirty 25．发现咬住 found stuck 26．发现挤压 found squeezed 27．发现弯曲 found bent 28．发现故障 found faulty 29．发现损坏 found damaged30．发现破碎成片 found broken to pieces 31．发现部分剥离 found partly detached 32．发现部分堵塞 found partly choked 33．发现剧烈震动 found violent vibration 34．发现烧坏 found burnt 35．发现断裂 found fractured 36．发现接地 found earthed 37．发现敲缸 found knocking 38．发现溶化 found melted away 39．发现泄漏 found leaking (found leaky) 40．发现冻结 found stuck fast by icing 41．发现锈蚀 found rusty 42．发现失效 found ineffective 43．发现故障 found out of order 44．发现结霜 found frosted 45．发现丢失 found lost46．发现出故障 found in trouble 47．发现失灵 found out of order 48．发现失灵 found out of action 49．发现不一致 found out of operation 50．发现错位 found out of place1．借 borrow我要向你借这份图纸I want to borrow the drawing from you. 我可以向你借这个手锤吗?May I borrow the hammer from you? 2．裂 break 阀杆断裂了The valve spindle is broken. 滚动轴承断裂成碎片了The ball bearing are broken to pieces. 3．加强 build up 叶轮应该堆焊The impeller should be built up by welding. 4． 烧 burn电动机烧了 The motor is burnt. 5． 进行 carry out 应进行负载试验The load test should be carried out. 6．吹blow管子必须用压缩空气吹清The pipe should be blown with compressed air.7．铸 cast按原样铸造一个8．引起 cause损坏是有剧烈振动引起的The damage was caused by violent vibration. 9．倒角 chamfer油槽须倒角 Oil groove is to be chamfered. 法兰切削后须倒角The flange should be chamfered after being machined.10．换掉 change把它们换掉,否则我拒绝验收Have them changed, otherwise I refuse to accept them.11．龟裂 chap轴瓦上的白合金龟裂了The white metal on the bearing bush is chapped. 12．核查 check用桥规核查主轴承Check the main bearing with bridge gauge.修理前后要核查拐档差Check the crankshaft deflection before andafter repair.13．清洁clean装前须清洁14．阻塞clog燃油滤器阻塞了The fuel filter is clogged.15．涂漆coat用红丹涂管子Coat the pipe with red lead.泵壳里涂防护漆The pump casing is to be coated with anti-fouling.16．完成complete finish你什么时候能完成修理工作?When can you complete (finish) the repair job?17．连接connect把电动机和淡水泵连接起来Connect the motor with the fresh water pump18．腐蚀corrode泵壳和叶轮均有腐蚀The pump casing and impeller are corroded.19．盖cover请把所有卸下的部件盖起来Please cover all the removed parts.20．裂No.2 cylinder head is cracked.21．吊crane把液压马达吊上岸去修理Crane the hydraulic motor ashore for repair.22．割cut把底座割掉Cut off the bedplate.23．损坏damage滚动轴承严重损坏The ball bearings are seriously damaged.24．脱落detach白合金部分脱落了The white metal is partly detached.25．查看detect查看氟里昂系统有无泄漏Detect the Freon system for leakage.26．解体disassemble解体,清洁并检查高压油泵Disassemble, clean and check the H.P. fuel pump.27．脱开disconnect把起动空气管脱开Disconnect the starting air pipe.28．讨论discuss我要和你讨论一下关于主轴承的问题。

轮机英语词汇目录1）第一部分柴油机Diesel Engine5）第二部分制冷和空调7）第三部分燃、滑油系统及油参数Fuel System ,Lubricating System &Oil Properties10）第4部分泵及其系统Pump &Pumping System11）第5部分船用锅炉Mair Boiler14）第6部分液压甲板机Hydraulic Deck Machinery17第7部分油水处理设备，轴系及推进器，造水机Oil Treatment,Oily Water Separator,Shafting &Propeller,Fresh Water Generator 18）第8部分交流发电机及配电板Alternating Current Generator& Switchboard20）第9部分法规及消防设备Watchkeeping,International Convention &Fire Fighting22）第10 部分维修常用词汇Useful Expressions in Repair List29）工具和量具Tools and Maeasuring Tools34）常用量词与缩写35）金属材料及其制品36）非金属材料及其制品36）化工材料37）电气材料37）油类38）紧固件,管接头39）船型40）船上构造The Structure of A ship第一部分柴油机Diesel Engine二冲程船用柴油机two stroke marine diesel engine四冲程船用柴油机four stroke marine diesel engine高（中，低）速柴油机high(medium, lower)speed engine气缸cylinder气缸盖cylinder cover(cylinder head)苏尔寿发动机Sulzer engineB&W型发动机Burmeister and Wain engine哥塔维根型发动机Gotaverken engine曼恩型发动机M.A.N.engineV型发动机V-type engine直流扫气式发动机uniflow scavenging type engine回流扫气式发动机loop flow scavenging type engine横流扫气式发动机crow-flow scavenging type engine十字头式发动机crosshead engine筒形活塞式发动机trunk-piston engine涡轮增压式发动机turbocharge engine固定部件fixed parts耐磨部件wear parts运动部件moving parts互换部件interchangeable parts气缸套cylinder liner示功阀indicator cock(indicator valve)安全阀safety valve气缸启动阀cylinder air starting valve缸套顶圈head ring for cylinder liner排气阀exhaust valve进气阀air inlet valve(suction valve)气阀传动机构valve driving mechanism顶杆tapper rod推杆push rod摇臂rocker rod (rocking lever)活塞piston十字头式活塞crosshead type piston筒形活塞trunk piston活塞头piston crown(head)活塞裙piston skirt活塞体piston body活塞销piston pin(gudgeon pin)活塞环piston ring气环（压缩环）compression ring刮油环oil scraper ring(oil ring,scraper ring)布油环oil distributing ring耐磨环wear ring活塞环槽piston ring groove活塞冷却水管piston cooling pipe往复管reciprocating pipe伸缩管telescope pipe铰链管articulated pipe活塞杆piston rod活塞杆凸缘piston rod flange活塞杆填料函stuffing box for piston rod活塞杆填料箱gland box for piston rod.packing gland for piston rod 填料函壳体stuffing box casing填料函张力弹簧tension spring for stuffing box填料函密封环sealing ring for stuffing box填料函刮油环scraper ring for stuffing box填料函压环pressure ring for stuffing box填料函压盖stuffing box gland十字头cross head十字头销cross head pin十字头销轴承cross head bearing(cross head pin bearing)十字头滑块cross head shoe(guide shoe)十字头导板cross head guide(guide rail,guide way,guide plate)连杆connecting rod连杆小端轴承connecting rod small end bearing连杆大端轴承connecting rod large end bearing;connecting rod bottom end bearing 曲柄销轴承crankpin bearing曲轴crank shaft曲轴臂crank arm曲轴销crank pin曲轴箱crankcase曲轴箱道门crankcase door(crankcase manhole)曲轴箱防爆门crankcase explosion door主轴承main bearing (bed plate bearing)倒挂式主轴承main bearing of under slung type轴承轴瓦上半块bearing bush-upper half轴承衬下半块bearing shell-lower half主轴承撑杆螺栓main bearing stay bolt主轴颈crank shaft journal(main journal)机座bed plate底座横隔板bed plate transverse member机架frame(column,entablature)底角螺栓holding down bolt (anchor bolt)贯穿螺栓through bolt (tie rod,tie bolt)贯穿螺栓护盖protecting covering for tie rod贯穿螺栓导套guide bush for tie rod推力轴thrust shaft推力轴承thrust bearing推力块thrust pad盘车机turning gear废气涡轮增压器exhaust gas turbocharge (turbo-blower)增压系统super charging system机械增压mechanical supercharging单（复）式增压系统single(complex)type super charging system二级增压two-stage supercharging定压增压系统constant pressure charging system脉冲增压系统impulse pressure charging system变压增压variable pressure charging system串联增压super charging in series syatem并联增压super charging in parallel system直流扫气unislow scavenging回流扫气loop scavenging横流扫气cross scavenging气口扫气port scavenging气口-气阀扫气port-valve scavenging扫气口scavenging port排气口exhaust port排气总管exhaust manifold排气管exhaust pipe上止点top dead center(TDC)下止点bottom dead center(BDC)燃烧室combustion chamber吸气行程inlet(suction) atroke压缩行程compression stroke做功行程power (working) stroke排气行程exhaust stroke定时图timing diagram指示功indicated power轴功shaft power示功图indicator power控制系统control system启动控制装置control devic for starting起动装置starting devic主起动阀main starting valve空气压缩机air compressor空气瓶air bottle(air container,air cylinder,air reservoir) 起动手柄starting lever(starting handle)起动空气控制阀starting air control valve起动空气导阀starting air pilot valve起动阀starting valve分级活塞stepped piston起动阀连锁装置starting valve blocking device起动凸轮starting cam起动空气管starting air pipe单凸轮换向装置single cam reversing device双凸轮换向装置double cam reversing device正车凸轮ahead cam正车油缸ahead oil cylinder (ahead oil bottle)自动停车装置automatic cut-out device空气分配器凸轮air distributor cam转向指示器running direction indicator换向杆reversing lever换向控制杆reversing control lever排气凸轮exhaust cam喷油凸轮fuel cam主起动阀手轮hand wheel for starting valve飞轮flywheel;turning wheel调速器goernor调速装置control device for running the engine 极限调速装置maximum-speed governor gear定速调速装置constant-speed governor gear全制式调速装置variable-speed governor gear机械调速器mechanical governor液压调速器hydraulic governor车钟telegraph凸轮传动机构camshaft transmission gear链条传动chain transmission(chain drive)齿轮传动gear tansmission链轮sprocket (sprocket wheel)惰轮idle wheel备车stand by engine完车finish engine停车stop engine微速前进（后退）dead slow ahead (astern)前进（后退）一slow ahead (astern)前进（后退）二half ahead (astern)前进（后退）三full ahead (astern)紧急前进（后退）三emergency full ahead(astern)起动start倒车reverse空气分配器air distributor气缸注油器cylinder lubricator第2 部分制冷和空调制冷refrigeration空调air conditioning通风ventilation盐水制冷brine refrigeration热电制冷thermoelectric refrigeration蒸汽压缩循环vapour-compression cyle制冷剂refrigerant直接制冷剂primary refrigerant间接制冷剂secondary refrigerant氟利昂freon氟化氢fluorinated hydrocarbon临界温度critical temperature压缩机compressor蒸发器evaporator感温包sensing bulb膨胀阀expansion valve电磁阀solenoid valve干燥器drier/dryer冷凝器condenser储液器liquid receiver油分离器oil seperator中间冷却器inter cooler内部均压装置internal equalizer风冷冷凝器air-cooled condenser双阀座截止阀double seat stop valve手动能量控制阀hand capacity control valve水量调节阀water regulating valve气动薄膜碟阀pneumatic film flap valve出液阀delivery valve出液管outlet pipe外平衡管outer balance pipe半封闭式压缩机semi-enclosed compressor节流阀throttle valve加湿器humidifier回油装置oil-return device回气管return pipe自动水量调节阀automatic water regulating valve自动液压能量控制装置automatic hydraulic capacity control device 压力控制器pressure control压差控制器differential pressure control吸入截止阀suction stop valve吸入滤网suction stainer充液阀charging valve冷凝器进入阀condenser inlet valve冷凝器出液阀condenser outlet valve冷却盘管cooling coil冷库insulted hold空气加热器air heater空气滤清器air cleaner油位检查镜inspection glass for oil level油预热器oil preheater卸载油缸unloading cylinder波纹管bellows制冷剂瓶refrigerant bottle热力膨胀阀thermostatic expansion valve毛细管capillary tube膜片diaphragm阀孔隙orifice恒温器thermostant诱导器inducer背压调节阀back-pressure valve浮动式自动回油阀floating type automatic oil return valve热交换器heat exchanger高压继电器high voltage relay温度调节器humidistat能量调节阀capacity regulator通风机ventilator舱室温度控制器cabin type temperature control排气融霜管discharge defrost pipe液位控制器liquid level control液体分离器liquid separator捡漏灯halide lamp船用臭氧发生器marine ozonizer温包式温度控制器phial type temperature controller湿度控制器humidity controller蒸发盘管evaporator coil tube散热器radiator空气调节器air conditioner二次空气系统secandary air conditioning system中央空调系统central air conditioning system高速诱导式空调系统high speed induction air conditioning system 半导体空调器semi-conductor air conditioner热泵式空调器heat-pump air conditioner窗式空调器window-type air conditioner毛发式气动湿度控制器pneumatic hair humidity controller风管air pipe出风栅outlet grid再加热盘管reheating coil空气干燥室air drying chamber顶式布风器top ventilator进风栅inlet grid挡水曲板curve flap翅片管tuberculat pipe散热盘管radiator coil tube挡板baffle翅状散热片fin波形散热片gill单风管系统single duct system双风管系统twin duct system分区加热器zone heater终端加热器terminal-heater压力通风plenum第3部分燃，滑油系统及油参数Fuel System ,Lubricating System &Oil Properties燃油系统fuel oil system双层底油舱double bottom fuel tank粗滤器strainer细滤器filter双联细滤器dual oil filter(duplex oil filter)燃油驳运泵fuel transfer pump沉淀柜settling tank分油机oil separator滑油柜/日用油柜lubricating oil tank\daily service tank加热器heater增压泵booster pump三通阀three way valve集油井oil head tank (oil header,oil collector buffer tank ,balance tank) 高压油泵（燃油喷射泵)fuel injection pump油孔式喷油泵（柱塞式油泵，plunger type fuel injection pump布式油泵）(Bosch fuel injection pump)回油孔fuel return hole进油孔fuel inlet hole柱塞（芯子）plunger柱塞套筒（柱塞导管）plunger guide bush(plunger barrel,plunger load)调节齿杆（调节齿条）control rack(toothed control rod)调节齿圈（调节齿套）control sleeve(control pinion)排油阀fuel delivery valve回油阀式高压油泵spill valve type fuel injection pump进油阀suction valve (spill valve,blowthrough valve)油量调节机构fuel relgulation linkage油泵行程调节杆regulating lever for pump stoke油压调节阀fuel pressure regulating valve保压阀pressure retaining valve高压油管high pressure fuel pipe喷油器fuel injector,fuel valve,fuel injection valve喷油器壳体fuel injector holder(fuel injector housing)喷油嘴injectin nozzle(nozzle)针阀needle valve针阀顶杆spindle溢流管overflow pipe蒸汽加热器steam heater蒸汽加热管steam heating pipe蒸汽加热盘管steam heating coil润滑系统lubricating system干油底壳式润滑dry oil sump type lubrication湿油底壳式润滑wet oil sump type lubrication飞溅润滑splash lubrication中压（低压）润滑系统medium pressure lubrication system(low pressure lubrication system) 气缸润滑cylinder lubrication轴承润滑bearing lubrication气缸注油器oil squirt(cylinder lubricator)吸油管suction duct(suction line)储油箱oil storage tank调节控制杆control lever for adjusting oil油孔oil orifice(oil hole)油道oil way(oil channel)油底壳oil sump(sump tank,crank bilge) 污油柜oil sludge tank滑油循环柜circulating lube oil tank滑油粗滤器lube oil strainer滑油泵lube oil pump滑油冷却器lube oil cooler比重（相对密度）specific gravity (relative density) 黏度viscosity发火质量ignition quality十六烷值cetane number柴油指数diesel index闪点（开口/闭口）flash point (open /closed)倾点pour point浊点cloud point凝点freezing point残碳值carbon residue灰份ash content水分water content硫分sulphur content热值calorific value机械杂质mechanical impurities油品等级grade of oil馏程distilling rang矾含量vanadium content铝含量alumminium content船用轻柴油marine gas oil (MGO)船用燃料油marine fuel oil(MFO)船用柴油marine diesel oil (MDO)中间燃料油internal fuel oil添加剂additive总酸值total acid number(TAN)强酸值strong acid number (SAN)总碱值total base number (TBN)沉淀物含量sediment抗氧化安定性oxidation resistance抗腐蚀性corrosion极压添加剂extreme pressure additive黏度指数viscosity index第4部分泵及其系统Pump &Pumping System船用泵marine pump立式泵vertical pump卧式泵horizontal pump单缸泵single cylinder pump双缸泵duplex pump单（双）作用泵single(double)-acting pump单级泵single-stage pump双级泵double-stage pump定量泵constant-delivery pump变量泵constant displacement pump(constant delivey pump) 自吸式泵self-priming pump非自吸式泵none-self priming pump容积式泵displacement pump轴流泵axial-flow pump离心泵centrifugal pump往复泵reciprocating pump活塞泵piston pump柱塞泵plunger pump径向柱塞泵radial plunger pump轴向柱塞泵axial plunger pump回转泵rotary pump叶片泵vane pump单（双）作用叶片泵single(double)-acting pump齿轮泵gear pump水环泵water ring pump内（外）齿轮泵inside(outside)gearing pump螺杆泵screw pum液压泵hydraulic pump径流泵radial-flow pump旋涡泵volute pump喷射泵ejector pump蒸汽直接作用泵direct-acting steam driven pump主机驱动泵min-engine-driven pump冷却水（油）泵cooling water(oil)pump给水泵feed pump备用给水泵donkey feed water pump卫生水泵sanitary pump出灰泵ash-ejecting pump压载水泵ballast pump污水泵sewage pump凝水泵condensate pump引水泵priming pump(primer pump)盐水泵brine pump淡水泵fresh water pump消防泵fire pump舱底水泵bilge pump循环泵circulating pump真空泵vacuum pump驳运泵transfer pump排污泵slusge pump变量泵variable output pump洗仓泵tank cleaning pump增压泵booster pump泵壳pump housing泵体pump body泵缸pump cylinder泵缸套pump line填料箱stuffing box吸入阀suction valve净正吸入压头net positive suction head (NPSH)系统水头损失system head loss泵浦特性曲线pump characteristic curve排出discharge (delivery)流道liquid path叶轮impeller (vane wheel)扩压管diffuser蜗壳volute管路pipe line旋塞（考克）cock止回阀non-return valve碟形阀butterfly valve闸板阀gate valve转阀rotary(rotating) valve滑阀slide (sliding)valve球形阀globe valve安全阀relief valve速闭阀quick closing valve (strip valve)集中引水系统central priming system (CPS)第5部分船用锅炉Mair Boiler火（水）管锅炉fire (water) tube boiler立（卧）式锅炉vertical (horizonatal)boiler直（横，弯，盘，指）管锅炉straight(cross,bent,coil,thimble)-tube boiler废气锅炉exhaust boiler管式锅炉tubular boiler筒形锅炉cylindr boiler (shell type boiler)鼓筒形锅炉drum boiler燃油辅助锅炉oil-burning auxiliary boiler立式横烟管锅炉vertical fire tube boiler卧式三回程火管锅炉horizontal triple-pass fire tube boiler盘管式强制循环废气锅炉coil-tube forced-circulation exhaust boiler 人孔门manhole door水包water drum水管联箱water header水冷壁water-cooled wall (water screen, water wall) 上升管riser tube下降管down comer后水冷壁rear water wall tube侧水冷壁side water wall tube沸腾联箱steaming header沸水管boiling-water tube炉膛furnace (fire box)炉胆furnace flue炉排fire bar(fire grate)炉门fire door炉衣boiler clothing (boiler lagging)炉墙furnace wall耐火砖衬层fire-brick lining挡烟墙baffle wall给水阀feed water valve给水截止阀feed water stop valve给水止回阀feed water check valve汽鼓（汽锅筒）steam drum汽水分离器steam purifier (steam separator)内给水管intrnal feed pipe给水离子交换器feed water ion exchanger省煤器（经济器）economizer上部联管upper header下部联管lower header前部联管front header后部联管rear header进口分配联管inlet distributing header出口分配联管outlet distributing header水位表water level gauge玻璃水位表glass water level gauge低位水位表bottom water level gauge远距离水位显示计remote water level indicator水位计分支阀（通汽考克，通水考壳）water level root valve(steam cock,water cock) 光滑管plain tube带肋片的蛇形管coil tube with ribs水位调节器water level regulator低水位保险装置low-water level cut-off device危险水位报警器low-water level alarm热水井hot well热水循环泵hot water regulating pump水处理water treatment上排污阀surface blow-down valve底部排污阀bottom blow down valve上（下）部吹除阀surface(bottom) blow-off valve浮渣盘scum dish烟管smoke tube烟箱smoke chamber(smoke box)烟道smoke flue烟囱chimney(funnel)烟喉furnace uptake牵条stay牵条管stay tube支承管support tube波形管sinuflo tube麻花管swirlyflo tube吹灰器soot blower单层盘管single-layer tube燃烧器oil burner燃油预热器oil preheater雾化器burner atomize (sprayer)雾化片sprayer plate喷油嘴burner tip (nozzle)喷油嘴管架nozzle support喷油嘴体nozzle holder喷孔nozzle hole(nozzle orifice)旋涡室swirl chamber点火器igniter点火喷油嘴ignition nozzle点火变压器ignition transformer预燃室precombustion chamber调风器air register调风门air damper风门throttle (air intake flap)风门伺服器servomotor for throttle regulation风口draught door风箱burner wind box风机blower手调风门hand regulating throttle空气调温器air attemperator空气扩散盘air diffuse disk导流器air director空气调节器air regulator (air register)强制通风机force draught fan火焰检测器flame detector火口fire hole(combustion head)比例操作器proportional ratio apparatus压力比例操作器pressure ratio regulator停汽阀steam stop valve集汽管steam receive蒸汽分配器steam distributor阻汽器steam trap过热器super-heater减热器desuper heater旋风汽水分离器cyclone steam separator除氧器deaerator第6部分液压甲板机械Hydraulic Deck Machinery液压泵hydraulic pump径向柱塞泵radial plunger pump中央阀center valve配油轴oil distribution shaft配油盘oil distribution disc配油套oil distribution sleeve配油口oil distribution port配油壳oil distribution casing配油阀oil distribution valve浮动环floating ring压力管pressure pipe伺服活塞srevo-piston差动活塞differential piston倾斜盘swash plate液压放大器hydraulic amplifier液压马达hydraulic motor高速小扭矩油马达high speed low torque oil motor齿轮式（叶片式，轴向柱塞式）油马达gear-type (vane-type,axial-plunger-type)oil motor 低速大扭矩油马达low speed high torque oil motor柱塞式油马达plunger-type oil motor径向柱塞式油马达radial-plunger-type oil motor单作用径向柱塞式油马达single-acting radial-plunger-type oil motor轴向双斜盘式油马达axial-double-tilting frame type oil motor液压油缸hydraulic oil cylinder单作用柱塞油缸single-acting plunger oil cylinder摆动油缸oscillating oil cylinder差动油缸differential oil cylinder转叶式油缸rotary-vane-type oil cylinder定叶fixed vane转叶rotary vane密封条sealing strip定子stator转子totor压力控制阀pressure control valve顺序阀sequence valve直控～direct-control valve单向～one-way valve(check valve)卸载～off-load valve遥控～telecontrolled valve液控～hydraulically controlled valve减压阀pressure-reducing valve定压～constant pressure valve定差～constant difference valve定比～constant ratio valve溢流阀overflow valve先导式～pilot valve直动式～direct-acting valve差动式～differential valve流量控制阀flow control valve节流阀throttle valve调速阀speed-regulating valve方向控制阀direction control valve直通式～straight one-way valve直角式～angle one way valve手动截止阀hand stop valve (hand cut-off valve)双路油压自锁阀double-circuit oil pressure self-closing valve 换向阀change-over valve (change valve)电磁～electro-magnetic valve电液～electro-hydraulic valve转阀（滑阀）ritary valve (side valve)三位四通阀three-position four-way valve主阀main valve辅阀auxiliary valve先导阀pilot valve阻尼孔damper hole节流缝隙throttle slot舵机steering gear定量泵开式系统open oil system of the constant delivery pump变量泵闭式系统closed oil system of the variable delivery pump撞杆式舵机ram type steering gear转叶式舵机rotary vane type steering gear工况选择阀operating mode selector valve手动旁通阀hand by-pass valve反馈杆feed back rod自锁阀self-locking valve防浪阀storm valve舵rudder舵柱rudder post舵柄rudder tiller舵托（承）rudder carrier舵叶rudder blade舵杆rudder stock撞杆ram操纵系统control system机械杠杆反馈式追随机构follow-up system of the mechanical lever feedback type 应急手动操纵装置emergency hand control device浮动杆floating lever副杠杆auxiliary lever遥控操舵装置telemotor steering gear起货装置cargo handing gear起货绞车cargo winch回转起货机crane吊扬索（千斤索）topping lift吊货杆boom(derrick boom)吊臂jib(crane jib)吊臂止动器jib stopper机械制动器machanicalbrake防索松保护器slack wire protection变幅绞车luffing winch货物定位装置cargo psotler差动型限位开关differential limit switich旋转绞车slewing winch带式刹车band brake旋转底盘slewing rim起锚机windlass止链器cable stopper锚anchor锚链anchor chain(anchor cable,chain cable)锚链轮chain lifter(cable lifter,cable holder)锚链舱chain locker链轮止动器chain lifter brake离合器clutch绞盘capstan绞盘卷筒capstan barrel带缆卷筒warping drum锚链卷筒chain drum绞车卷筒winch barrel(winch drum ,winding barrel)第7部分油水处理设备，轴系及推进器，造水机Oil Treatment,Oily Water Separator,Shafting &Propeller,Fresh Water Generator分油机oil separator离心分油机oil centrifuge分杂机clarifier分水机purifie造水机fresh water generator真空沸腾式造水机vacuum boiling type fresh-water genetator真空闪发式造水机vacuum flash type fresh-water generator工作水operating water冲洗水flushing water配水盘paring disc活动底盘sliding bowl bottom滑动圈operating slide污渣出口sludge outlet分离筒separator bowl分离筒本体bowl body分离筒盖bowl hood分离筒转轴bowl spindle分离盘bowl discs机盖frame cap阻水环damp ring比重环gravity disc油水分离器oily water separator舱底水bilge锥形盘conical plates粗粒化coalesce放油阀oil drain valve检验旋塞check cock自动空气释放阀automatic air rlease valve除油阀oil rcovery valve (recovered oil valve)液位探测电极liquid level electronic probe除渣阀scum valve自动出油阀automatic oil outlet valve储油柜oil storage tank控制板control panel轴系shafting螺旋桨propeller传动轴transmission shaft中间轴intermeditate shaft (tunnel shaft)推力轴thrust shaft单环推力轴single collar thrust shaft艉轴tail shaft (tube shaft)可调螺距螺旋桨adjustable pitch propeller (variable pitch propeller,controllable pitch propeller)定距桨constant pitch propeller固定桨叶螺旋桨fixed-blade propeller艏部螺旋桨bow propeller横向推理器transverse propeller左（右）螺旋桨left(right)handed propeller推力轴承thrust block推力块thrust pad推力环thrust collar刮油器scraper挡油圈oil deflector油位显示器oil level indicator单环推力轴承（密歇尔推力轴承）Michell thrust bearing(single collar(thrust)bearing)支撑轴承（中间轴轴承)tunnel bearing(intermediate shaft bearing)艉轴管轴承sterntube bearing (stern bearing)铁梨木轴承lignumvitae bearing水润滑轴承water-lubricated bearing白合金轴承white metal bearing桨叶propeller blade空泡cavitation螺旋桨空泡propeller-cavitation压力面空泡pressure-face cavitation(face cavitation)吸力面空泡suction-face cavitation导边空泡leading edge cavitation蒸发器evaporator加热器heater冷凝器condenser挡水器demiser抽气喷射器air ejector凝水泵distillate pump盐水泵brine pump闪发室flash chamber盐度计salinity indicator第8部分交流发电机及配电板Alternating Current Generator& Switchboard交流发电机altemator直流发电机dynamo发电机generator电磁式发电机electro-magnetic generator励磁场线圈magnetic field coil自励self-excited串励serise-wound并励shunt-wound复励compound-wound定子stator转子rotor电刷electric brush灭弧罩arc shield原动机prime motor配电箱distribution board主配电板main switch board区域配电板section board汇流排bus bar配电板load-dispatching board(switch board) 频率fequency相位phase同相in phase同步指示器synchroscope自动电压调节器automatic voltage regulator (AVR)自动分载装置automatic load-sharing device自动调频调载器automatic frequency and load regulator 发电机屏genertor pnel试验板test board供电网supply network岸电接线箱shore connection box脱扣装置trip device保护装置protection device欠压装置under-voltage protection失压装置no-voltage protection过载保护over-load protection过流保护over-current protection逆功率保护reverse power protection缺相保护open-phase protection短路电流保护short circuit current protection操纵平台control platform开关switch过载开关overload switch双刀开关double pole switch限位开关limit switch断路器breaker断流器cut-out自动断路器automatic circuit breaker过载断路器over load circuit breaker空气断路器air circuit breaker整流器rectifier变压器transformer耦合变压器couple transformer放大器amplifier换向器commutator起动器stater继电器relay电抗器reactor电阻器resisor电容器condenser (capacitor)接触器contactor接线盒connection box并车操作parallel operation电流表ammeter电压表voltmeter功率表wattmeter频率表frequency meter并车开关paralleling switch电动机motor三相电动机three-phase motor同步感应电动机synchronous induction motor异步电动机asynchronous motor鼠笼式电动机squirrel cage motor第9部分法规及消防设备Watchkeeping,International Convention &Fire Fighting STCW 公约《1978年海员international convention on standards of training, 培训，发证和值班标准certification and watchkeeping for seafarers 1978国际公约》值班watchkeeping值班人员watchkeeper (watchkeeping personnel)航行值班underway watch接班人员relief定员rating任职资格qualification值班要求watch requirements对职责的适应fitness for duty职责范围areas of responsibility日常调节routine adjustment逃生路线escape routes驾驶台命令bridge order轮机日志engine room log book无人机舱un-attended machinery space (UMS)(unmanned machinery space)国际公约international convention国际海事组织international maritime organization (IMO)海事委员会maritime commission()MARPOL公约《1973年防止international convention for the prevention of pollution船舶污染国际公约》（1978年修正）from ships 1973 (as modified by the protocol of 1978 relating therto)SOLAS公约《国际海上人命安全公约》international convention for the safety of life at sea油类记录簿oil record book国际防止污染证书(IOPP)international oil pollution prevention certificate原油洗舱(COW) crude oil washing system惰性气体系统(IGS) inert gas system专用压载舱(SBT) segregated ballast tanks清洁压载舱(CBT) clean ballast tanks排油监控系统oil discharge monitoring and control system焚烧炉incinerator散装有害液体货物记录簿cargo record book for ships carrying noxious liquid substances in bulk 国际散装有害液体运输防污证书international pollution prevention certificate for the carriage of noxious liquid substances in bulk客船安全证书passenger ship safety certificate货船无线电安全证书cargo ship safety radio certificate货船结构安全证书cargo ship safety construction certificate货船设备安全证书cargo ship safety equipment certificate中国船级社china classification society(CCS)中华人民共和国船舶检验局the register of shipping of the people's republic of china (ZC)定期检验periodical survey更新检验renewal survey年检annual survey中间检验intermediate survey火警探测器fire detector感烟探测器smoke detector火焰探测器flame detector感温探测器heat detector烟管警报系统smoke pipe fire alarm system蜂鸣器buzzer警铃alarm bell警报器howler灭火剂extinguishant灭火设备fire fighting equipment固定灭火设备fixed fire fighting equipment便携式灭火器portable extinguisher碳酸钠与酸混和灭火器soda-acid extinguisher泡沫式灭火器foam extinguisher化学泡沫式灭火器chemical foam extinguisher机械泡沫式灭火器mechanical foam extinguisher二氧化碳灭火器carbon-dioxide extinguisher干粉灭火器dry powder extinguisher插销plunger钢瓶steel container喷嘴nozzle把手handle排出管discharge hose触发开关trigger control喇叭状喷管horn固定灭火装置fixed fire fighting installation救火泵fire pump应急救火泵emergency fire pump增压泵booster pump消防栓hydrant皮龙管hosepipe(hose)快速扣合接头snap-in connector喷头sprinkler head (sprayer)泡沫发生器foam generator惰性气体发生器insert gas generator消防部署fire fighting strategy消防演习fire fighting drills呼吸面具breathing apparatus卤化烃系统halon system卤化烃1301 halon 1301(BTM)卤化烃1211 halon 1211(BCF)第10 部分维修常用词汇Useful Expressions in Repair ListA. 故障Troubles发现已无法修复found beyond repir发现尺寸过大found over-sized发现反应缓慢found slow function发现不正常found out of order发现不合标准found not up to standard发现不准确found inaccurate发现失效found ineffective发现失去作用found out of function发现咬住found seized发现冻结found stuck fast by icing发现过热found over heated发现过度磨损found excessive wear(found worn out;found worn away) 发现有一点倾斜found a little bit inclined发现因过热而毁坏found destroyed by over heating发现龟裂found chapped发现塌陷found collapaed发现运转失灵found out of operation发现呈椭圆形found oval发现拉痕found scored发现拉毛面积found scuffed about XX in area发现变形found deformed发现变形超过xx mm found deformed over a length of XX MM发现松动found loose发现油污found greasy发现赃污found dirty发现挤铅found squeezed发现弯曲found bent发现故障found faulty发现结霜found frosted发现损坏found damaged发现破裂成片found broken into pieces发现部分剥离found partly detached发现部分阻塞found partly blocked发现剧烈震动found violent vibration发现效率不高found low efficiency发现挠曲found twisted发现烧坏found burnt发现堵塞found choked发现断裂found fractured发现接地found earthed发现敲缸found knocking发现漏泄found leaking(leaky)发现熔化found melted away发现缩减约10mm found reduced about 10 mm发现在气缸内卡住found jammed up in the cylinder在某部位发现裂纹found cracked in way of如必要if necessary如发现必要if found chapped如发现有毛病any defectives if found一般要求General Requirements一式两份交轮机长to be handed over to C/Ein duplicate(two copies)一式三份交轮机长to be handed over to C/Ein triplicate(three copies)一式四份交轮机长to be handed over to C/E in quadruplicate送交轮机长to be sent to C/E(to be delivered to C/E;TO be submitted to C/E) 厂供to be supplied by yard以备检验to be prepared for survey用波浪键修补to be remedied by means of metallock用船上备件替换to be replaced with ship's spare用千斤顶提起to be jacked up出具证书certificates to be issued出具检验报告survey report to be issued充to be charged充以二氧化碳气体to be filled with co2 gas运至to be transported to取消to be cancelled供应to be provided供验船师检验to be presented for surveyor's inspection所有钢瓶测试all bottles to be calibrated所有钢瓶称重all bottles to be weighted制造并供应to be made and supplied按现有的制作并安装to be fabricated and installed according to the existing one 除霜to be defrosted砌to be paved重充氟里昂12 to be refilled with freon 12重充水银ti be recharged with marcury送至to be removed to(to be sent to;to be transferred to )送车间修理to be sent to work shop for repaira退回船上作备用to be returned to ship as spare绘制图纸交船srawing to be made and sumitted to ship按要求修理to be repaired as required按302项处理treated as item 302换新to be renewed消除eliminated修理时用盲板封口blinded during repair移至to beshifted to船供to be supplied by ship提供作备件用to be supplied as spare船舶所有人供应to be supplied by owner焊补to be patched up by welding提供to be furnished割掉to be cut off照样新作newly made as per sample增加to be addedC拆卸Dismantling从环槽中取出to be taken out from ring grooves打开检查to be opened up for inspection用干冰拧松to be shrunken with dry ice(to be softened with dry ice)用加热放松to be untightened by heating吊出to be lifted out拆卸to be dismantled拧松to be loosened拔出to be drawn out拔出检查to be pulled out for inspection。

一、专业词汇翻译1. Connecting rod 连杆/活塞杆2. four-stroke diesel engine 四冲程柴油机3. top dead center上止点/下止点4. reduction gear box 减速齿轮箱5. cooling jacket 冷却水套6. cylinder liner 气缸套7. piston skirt 活塞裙/活塞环8. running-in period 磨合期9.船用排气锅炉marine exhaust gas boiler 10. crankpin bearing 曲柄销轴承11.吸气行程suction stroke/压缩冲程12. circulating pump循环泵13. sea water cooling system海水冷却系统14. indicated power 指示功/效率15. compression ratio 压缩比16. 废热回收系统waste heat recovery system17.废气再循环exhaust gas recirculation 18. 扫气口scavenge port/扫气箱19.船级社classification society 20. 辅助风机auxiliary blower21. inlet valve 进气阀/排气阀22. 涡轮增压器turbocharger23. main starting valve主启动阀 24. 曲轴crankshaft25.机架/燃烧室/直流扫气/十字头滑块/导板……二、英译汉1．It is usually desirable to fit charge-air coolers to turbocharged two-stroke engines. The coolers are located between the turbo-blowers and the cylinders. As the charge-air density increases, the amount of air flowing into the cylinders is increased and as the charge-air temperature lowers, the exhaust temperature and the engine thermal loading are reduced.1．对于涡轮增压式二冲程发动机来说，通常希望能装有增压空气冷却器。

基本专业英语一、常用运行ON开（状态，常指信号）OFF关（状态，常指信号）OPEN 开(状态，常指阀门)CLOSE关（状态，常指阀门）START 启动STOP 停止ALARM报警OPERATE 运行；操作TRIP 跳闸TEST 试验INDICATION；DISPLAY指示；显示INLET入口OUTLET 出口INPUT输入OUTPUT 输出AUTOMA TION/MANUAL(HAND) 自动/手动AUXILIARY辅助LOCAL就地REMOTE摇控PRESSURE 压力TEMPERATURE 温度FLOW 流量SPEED 速度RPM 转/分SYSTEM 系统BYPASS旁路PIPE；TUBE 管道，管子PURGE 吹扫V ALVE 阀门UNIT单元、机组PRINT 打印CURVE，LINE 曲线，线BALANCE 平衡INSTRUMENT AND CONTROL 仪表与控制MODE方式，模式SET POINT设定点TRANSMITTIER；TRANSDUCER 变送器；传感器CODE 代码；编码DA TA 数据；文件；资料STA TIC静态DYNAMIC动态COLD START—UP 冷态启动WARM START—UP 温态启动HOT START—UP 热态启动RESET复位SELECT选择UNA V AIL 不允许(不能投用的)FAST 快SLOW慢NORMAL 正常INCREAS 增加DECREAS减少二、锅炉部分BOILER 锅炉SUPERHEATER 过热器REHEATER 再热器WATERW ALL 水冷壁DOWM COMER 下降管HEADER 联箱、母管STEAM DRUM 汽包DURM PRESSURE 汽包压力ATTEMPERATOR 减温器SPRAY 喷水ECONOMIZER 省煤器ISOLATION 隔离；绝缘CHIMNEY；STACK 烟囱FLUE GAS 烟气WATER 水STEAM 蒸汽SAFETY V ALVE 安全阀DRAIN AND VENT 疏水和排气Boiler Maximum Continuous Rating 锅炉最大连续出力PRESSURE DIFFERENCE 压差BOILER TRIP RESET 锅炉跳闸复位OPERATE MODE SELECT 运行方式选择MANUAL MODE 手动方式MAIN STEAM TEMP/PRESSURE/FLOW 主汽温度/压力/流量FEED WATER FLOW 给水流量REHEATER 再热器manhole 人孔，检修孔Taps 接头pipe taps 管接头test wells 测点插孔Atmosphere 大气Condensate Polisher 除盐装置Safety Valve 安全阀Control Valve 控制阀Saturate 饱和的Flash Tank 扩容箱Flame 火焰三、汽机部分STEAM TURBINE 汽轮机TURBINE GENERATOR 汽轮发电机组CYLINDER 、CASING 汽缸STA TOR 定子ROTOR 转子BEARING 轴承SHAFT 轴BLADE 叶片GEARING 盘车NOZZLE 喷嘴FLANGE 法兰SEAL 密封BEARING BRASS 轴瓦MAIN OIL PUMP 主油泵MAIN STOP V ALVE 主汽阀EMERGENCY GOVERNOR 危急保安器JACKING OIL PUMP 顶轴油泵FILTER 滤网SILENCER 消音器SUCTION PUMP 抽吸泵SYNCHRONIZER 同步器GOVERNOR 调速器HIGH PRESSURE HEATER 高加LOW PRESSURE HEA TER 低加CIRCULATING PUMP 循环泵CONDENSATE PUMP 凝泵CONDENSER HOT WELL 热井LUBE OIL PUMP 润滑油泵MAKE－UP WA TER 补给水OIL STORAGE TANK 储油箱DEMI WATER 除盐水CLOSED COOLING W ATER 闭式冷却水EXTRACTION STEAM抽汽DEAERATOR 除氧器CONDENSER 凝汽器EXHAUST 排汽EJECTOR 喷射器，抽气器V ACCUM 真空EXPANSION 膨胀VIBRATION 振动CIRCULATING 循环1ST STAGE PRESS 第一级压力OPERATE MODE SELECT 运行方式选择OPERATE MANUAL MODE 手动方式MANUAL LOAD SET手动负荷设定TURBINE INLET PRESSURE 汽机入口压力DEAERATOR LEVEL CONTROL V ALUE 除氧器水位控制阀CONDENSER LEVEL CONTROL V ALUE 凝汽器水位控制阀surface condenser 表面凝汽abnormal and normal conditions 变工况和额定工况warm up 暖机Axis Thrust 轴向推力BFP Boiler Feedwater Pump 锅炉给水泵Closed Circulating Cooling Water 闭式循环冷却水Check Valve 逆止阀Cooler 冷却器Heater 加热器Condensate 凝结水Coupling 联轴器Circulation Water Pump 循环水泵Differential Pressure Transmitter 压差变送器Drain Valve 疏水阀Efficiency 效率Extraction System 抽气系统Exhaust 排汽Feedback 反馈Flow transmitter 流量变送器Failure Alarm 故障报警Flange 法兰Gland Steam 轴封蒸汽Heat Conservation 保温Heat Balance 热平衡Level Gauge 液位计Level Alarm 液位报警HP High Pressure 高压IP Intermediate Pressure 中压LP Low Pressure 低压Lubricating Oil 润滑油.MAX Maximum 最大的，最大值的MIN Minimum 最小的Measure 测量Main Steam Valve 主汽阀Pressure Alarm High 高压报警Pressure Alarm Low 低压报警PB Push Button 按钮Pneumatic 气动的Protection 保护Program 程序Plant Water 厂用水Recirculation 再循环Transfer 转换Trouble 故障Tracking 跟踪四、电气部分CURRENT 电流DIRECT CURRENT(DC) 直流ALTERNATING CURRENT(AC) 交流VOLTAGE 电压RESISTANCE 电阻REACTANCE 电抗INDUCTANCE 电感CAPACITANCE 电容POWER 功率FREQUENCY 频率SPEED 速度，转速ACTIVE POWER 有功功率REACTIVE POWER 无功功率LOAD 负荷POWER FACTOR 功率因数LOSS损耗OVER CURRENT 过流OVER VOLTAGE过压OVERLOAD 过载EXCITE 励磁TRANSMISSION 传输COMMUNICA TION 通讯SIGNAL 信号MAGNETIC FIELD 磁场LINE线路GENERATOR发电机BUS 母线EXCITOR 励磁机MOTOR 电动机BUSCOUPLER 母联ASYNCHRONOUS MOTOR 异步电动机INSULATOR 绝缘子BUSHING套管ARMA TURE 电枢COIL 线圈MAIN TRANSFORMER 主变WINDING 绕组CORE 铁芯POLE 电极PHASE 相POTENTIAL TRANSFORMER 电压互感器CURRENT TRANSFORMER 电流互感器CONDUCTOR导体CABLE电缆SWITCH 开关NEUTRAL POINT 中性点GROUNDING(EARTHING)接地DISCONNECTOR(DS) 隔离开关BA TTERY 电池CLOSED-LOOP闭环OPEN-LOOP开环ABNORMAL CONDITION 异常状态CONFIGURA TION 结构，布置，外形INTERFACE 接口MCC 马达控制中心DCS DISTRIBUTED CONTROL SYSTEM 分散控制系统UNINTERRUPTED POWER SUPPL Y 不间断电源THERMO-COUPLE 热电偶Circuit Breaker 断路器Control 控制Controller 控制器Electric Operate 电气操作Field 磁场Generator Cooling 发电机冷却Rectifier 整流器Switchgear 开关装置GIS （gas insulated switchgear）气体绝缘开关五、电液调节及控制部分Valve calibr 阀门标定Trip diagram 遮断程序Hardware 跳线Customer trip 用户遮断Master protetive 主保护遮断EMERGENCY TRIP SYSTEM 危急跳闸系统FAST-ACTING SOLENOID 快动电磁阀INTERCEPT V ALVE 中间截流阀SHUT-OFF VALVE 切断阀BLOWDOWN VLV 泄放阀OVERSPEED PROTECTION CONTROL 超速保护控制AUTO SHUT-DOWN TRIP 自动停机遮断AUTO TURBINE CONTROL 自动汽轮机控制BOOSTER PUMP 前置泵PERMANENT MAGNETIC GENERATORDF 永磁发电机OIL GAUGE 油位表SEAL OIL 密封油CONTROL OIL 控制油SAFEL Y OIL安全油MAIN OIL PUMP 主油泵EMERGENCY OIL PUMP 事故油泵SUCTION PUMP 抽吸泵V ALVE POSITION 阀位置INTERCEPT V ALVES 中间截止阀COMBINED REHEAT V ALVES 中压联合阀FIRST STAGE PRESS 调节级压力MAIN STEAM PRESS 主蒸汽压力REHEAT PRESS 再热汽压力SPEED MONITORING 速度监视SPEED INCREASING 速度增LOAD SET 负荷设定IN STANDBY 在备用状态LOAD LIMITING SET 负荷极限设定LOAD INCREASING 负荷增LOAD DECREASING负荷减AT SET LOAD 在设定负荷V ACUUM TRIP 真空跳闸MAIN STEAM PRESSURE LIMITER 主汽压力限制器ACCELERATION 加速度TURN GEAR CONTROL SEQUENCE 盘车控制程序TURN GEAR PIGGY BACK MOTOR 盘车啮合电机TURN GEAR MOTOR 盘车主电机STEAM SEAL SYS 蒸汽密封系统STEAM SEAL BY-PASS UNLOAD VLV 蒸汽密封旁路泄放阀六、燃机1.Gas turbine 燃机air flow空气流量availability可用率base 基架，基础combined cycle联合循环F class (series, flame)F系列（级）fuel consumption燃料耗量gas generator燃气发生器（压气机＋驱动用透平）heat rate热耗performance性能reliability可靠性(thermal) efficiency（热）效率pressor 压气机abraidable coating可磨涂层（气封）air extraction port放（抽）气口air inlet 空气进口air inlet plenum (assembly)空气进口集流腔室（组件）air seal气封anti-surge 防喘振axial－flow compressor轴流式压气机（压缩机）bearing casing轴承壳体bearing housing轴承座bellmouth （inner，outer）承口（内，外）bleed valve放气阀brush seal 刷子气封compressor casing压气机气缸(中缸)compressor diffuser压气机扩压段（扩压器）compressor discharge casing压缩机排气缸compressor inlet casing压缩机进口缸（承力缸）compressor rotor压气机转子discharge air排气evaporative cooler 蒸发式冷却器exit guide vane(s)出口导叶extraction port 抽气口forward stub shaft前端轴inlet filter (house)进口过滤器（室）inner barrel (cylinder)内缸(off-line) water flush（脱机）水洗pulsation protection （control）喘振保护（控制）rotor blading动叶speed ring测速计齿环stator blading静叶surge margin喘振裕度wheel叶轮wrapper气缸外壁（固定燃烧室部位）bustor 燃烧室cap (cover) assembly （end cover）头部组件(端板，喷嘴安装座) catalytic combustion 催化燃烧centerbody中心体combustion system燃烧系统combustion zone燃烧区convection cooling对流冷却diffusion combustion 扩散燃烧diffusion (premixed) gas扩散（预混）气体燃料effusion cooling扩散冷却emission control排放控制film cooling气膜冷却flame detector火焰监测器flame-out熄火flame stabilizer火焰稳定器flow sleeve导流套筒fuel nozzle燃料喷嘴ignition点火multiple-combustion system 多燃烧室系统premixing combustion预混燃烧outer combustion chamber燃烧室外壳spark plug (igniter) 点火器air cooled blade 空冷叶片bucket动叶bucket dovetail叶根center rib (bucket)（叶片）中部龙骨coating 涂层exhaust diffuser排气扩压段exhaust frame排气缸，承力缸hot gas path（parts）高温燃气通道（零件）nozzle segment喷嘴弧段rabbet 止口sidewall （叶片）端壁thermal barrier coating （TBC）隔热涂层through bolt 贯穿螺栓trailing edge 出气边turbine casing透平前气缸wheel shaft (forward, aft) 端轴（前，后）七、其他1.阀门globe valve 球心阀gate valve 闸门阀ball valve 球阀butterfly valve 蝶阀diaphragm valve 膜板阀，隔膜阀needle valve 针型阀bellows seal valve 波纹管密封阀check valve 止回阀angle valve （coner）角阀reverse flow valve 换向阀water seal valve 水封阀safety valve 安全阀relief valve 减压阀float valve 浮阀motor valve 电动阀air motor valve 气动阀piston valve 活塞阀solenoid valve 电磁阀cock valve 两通阀3-way valve（cross valve）三通阀Block valve 隔断阀Blast furnace gas valve 高炉煤气阀Bleed valve 放散阀Ball stop valve 球阀Ball non-return valve 球形止回阀Back-press valve 止回阀Automatic regulating valve 自动调节阀Automatic cutout valve 自动切断阀Bolier feed alve 锅炉给水阀Bullet valve 球阀Clack valve 止回阀Condenser level control valve 凝汽器水位调节阀Cone valve 锥形阀Conversion valve 转向阀Coner valve 角阀Coupled valve 联成阀Cut-out magnetic valve 截止电磁阀Cycle tube valve 循环管阀Difference press regulation valve 差压阀Emergency stop valve 危急遮断阀Equilibrium slide valve 平衡滑阀Explosion relief valve 防暴安全阀Extraction check valve 抽汽逆止阀Needle valve 针形阀Muffle safety valve 消音器安全阀Internal spring safety relief valve 弹簧式安全阀Gas inlet valve 煤气放散阀Fule control valve 燃料控制阀Flow regulatering valve 节流阀Flood valve 溢流阀Fire valve 消防栓Extraction control valve 抽汽调节阀2.开关normally opened 正常开normally closed 正常关partial opening 部分开lock open 连锁打开lock close 连锁关闭fail open 出事故打开fail chose 出事故关闭fail lock 出事故锁住3.附件filter,strainer 过滤器reducer 减压器flexible hose 软质胶管spectacle flange 双孔法兰blind plate 盲板orifice 通气孔vent line 排气管线welding connection 焊接sight glass 观察孔screwing cap 螺帽blind flange 盖板hose connection 软管连接duplex filter 双重过滤器flow nozzle 测流嘴drain pit 排水坑seal pot 密封罐wire net 金属丝网regulator with filter 带过滤器的调节器plug 插头spray nozzle 喷雾嘴。

轮机英语词汇汇总一．职位及工种(Titles and type of work) 1．船长 Captain2．大副 Chief officer3．二副 Second officer4．三副 Third officer5．四副 Fourth officer6．水手长 Boatswain7．水手 Sailor & Seaman8．木匠 Carpenter9．轮机长 Chief engineer10．大管轮 Second engineer11．二管轮 Third engineer12．三管轮 Fourth engineer13．机匠长 Chief motorman15．机匠 Fitter16．加油工 Oil man17．大电 Chief electrician18．电工 Electrician19．车间主任 Workshop director20．工长 Section chief21．班长 Fore man22．钳工 Fitter23．主管工程师 Engineer in charge24．机务&船东 Superintendent &Super &Owner 25．助理工程师 Assistant engineer26．验船师（机）Register27．验船师（船）Surveyor28．油漆工 Painter29．焊工 Welder30．大橱 Chief cook31．物料员 Store keeper32．加油工 Oiler33．机工 Mechanic34．甲板员 Deck man35．电线工 Wireman36．外包工 Laborer37．铸工 Molder38．管子工 Pipe fitter39．起重工 Crane operator二、柴油机类(Words about diesel engine) 1．主机 Main engine2．二冲程柴 Twostrokediesel engine3．四冲程柴 Forestrokediesel engine4．高速柴油 High speed diesel engine5．中速柴油 Middle speed diesel engine6．低速柴油机 Low speed diesel engine7．气缸盖(缸头) Cylinder head8．安全阀 Safety valve9．释放阀 Relief valve10．示功阀 Indicator valve11．示功考克 Indicator cock12．空气起动阀 Air starting valve13．起动空气分配器 Air starting distributor 14．油头(燃油喷射器) Fuel injector15．排气阀 Exhaust valve16．气缸套 Cylinder liner17．冷却水套 Cooling water jacket18．气缸注油器 Cylinder lubricator19．活塞 Piston20．活塞头 Piston crown21．活塞裙 Piston skirt22．活塞销 Piston gudgeon pin24．活塞杆 Piston rod25．活塞环 Piston ring26．活塞环槽 Piston ring groove27．压缩环 (气环) Compression ring28．刮油环 (油环) Oil scraper ring29．减磨令 Wear ring (copper ring)30．伸缩管(水拉管) Telescopic pipe31．活塞冷却空间 Piston cooling space32．填料箱(函) Stuffing box33．填料箱密封环 Sealing ring for Stuffing box 34．填料箱压缩环 Pressure ring for Stuffing box 35．填料箱刮油环 Scraper ring for Stuffing box 36．扫气箱 Scavenging receiver37．扫气口 Scavenging port38．排气口 Exhaust port39．十字头 Cross head40．十字头销 Crosshead pin41．十字头轴承 Crosshead bearing42．十字头滑块 Crosshead slipper43．滑块 Guide shoe44．十字头导板 Crosshead guide plate45．连杆 Connecting rod46．连杆大端轴承 Bid end bearing47．连杆小端轴承 Small end bearing48．曲柄轴承 Crank bearing49．曲柄销 Crank pin50．曲轴 Crank shaft51．曲轴颈 Crank journal52．曲柄臂 Crank web53．拐档差 Crank deflection54．主轴承 Main bearing55．主轴颈 Main journal56．轴承瓦 Bearing bush57．上轴瓦 Upper bearing bush58．上轴瓦 Upper half59．下轴瓦 Lower bearing bush60．下轴瓦 Lower half61．推力轴承 Thrust bearing62．推力块 Thrust pad63．推力盘 Thrust disc64．推力轴 Thrust shaft65．底座 Bed plate66．机架 Frame67．曲柄箱 Crank case68．曲柄箱导门 Crank case door69．曲柄箱防爆门 ExplosionproofCrank case.70．定时齿轮 Timing gear71．飞轮 Flying wheel72．凸轮 Cam73．凸轮轴 Cam shaft74．喷油凸轮 Fuel injection cam75．链条 Chain76．链条轮 Chain wheel77．链条箱 Chain box78．推杆 Push rod79．摇臂 Rocker arm80．排气阀 Exhaust valve81．吸气阀 Suction valve82．排气总管 Exhaust manifold83．进气总管 Air inlet manifold84．高压燃油管 High pressure fuel pipe 85．活塞冷却水管 Piston cooling water pipe 86．法兰 Flange87．贯穿螺栓 Tie bolt (tie rod)88．端盖 Side cover89．滑油泵 Lubricating oil pump90．燃油泵 Fuel oil pump91．滑油泵齿轮 Gear for lubricating oil pump 92．燃油泵齿轮 Gear for fuel oil pump93．叶轮 Impeller94．柱塞 Plunger95．导杆 Guide rod96．导套 Sleeve97．滚动轴承 Ball bearing98．滑动轴承 Sliding bearing99．推力滚动轴承 Thrust ball bearing100．推力面 Thrust surface (thrust side) 101．盘车机 Turning gear102．增压器 Turbocharger103．涡轮机(透平) Turbine104．涡轮 Turbine wheel105．涡轮叶片 Turbine blade106．喷嘴 Nozzle107．废气叶轮 Exhaust impeller108．废气叶轮片 Exhaust blade109．废气端 Exhaust side110．透平端 Turbine side111．转子轴 Rotor shaft112．油泵 L.O. pump113．换向装置 Reversing device114．换向伺服期 Reversing servomotor115．压气机(鼓风机) Blower116．膨胀接 Expansion joint117．调速器 governor118．飞重 Flying weight119．补偿阀 Compensate valve120．针阀 Needle valve121．开口销 Cotter pin122．轴封 Shaft seal123．机械密封 Machinery seal124．配电盘 Switchboard125．应急配电盘 Emergency switchboard 126．应急发电机 Emergency generator127．滤器 Filter128．细滤器 Filter129．粗滤器 Strainer130．滑油滤器 L.O. filter131．燃油滤器 F.O. filter132．空气消音器 Air intake silencer132．空气滤器 Air intake filter133．空气瓶 Air bottle (receiver)134．分油机 Separator135．油水分离器 Wateroil separator136．净油机 Purifier137．燃油净化器 F.O. purifier138．二氧化碳 CO2139．二氧化碳瓶 CO2 bottle140．正时齿轮 Timing gear141．导向棒装置 Guide bar142．注油器驱动 Lubricator driver143．链条张紧装置 Chain tightener144．凸轮轴传动轮 Chain wheel on cam shaft 145．中间链链传动轮 Intermediate chain wheel 146．注油器驱动装置 Lubricator drive147．链条张紧装置 Chain tightener148．滚筒导座 Roller guide housing149．应急操纵台 Emergency console150．力矩平衡器 Moment compensator151．主启动阀 Main starting valve152．启动空气分配器 Starting air distributor 153．喷油器 Fuel valve154．扫气系统 Scavenge air system155．安全帽 Safety cap156．机座 Bed plate157．轴向振动减振器 Axial vibration damper158 贯穿螺栓 Arrangement of stay bolt159．示功器驱动装置 Indicator driver160．端罩 End shields161．气缸架 Cylinder frame162 气阀传动装置 Valve operating device163．摇臂润滑油泵 Rocker arm lubricating oil pump 164．摇臂润滑油柜 Rocker arm lubricating tank 165．摇臂润滑滤器 Rocker arm lubricating filter 三、船舶机械类(Words about marinemachinery)1．船用锅炉 Marine boiler2．废气锅炉 Exhaust boiler3．辅锅炉 Donkey boiler4．组合式锅炉 Combined boiler5．火管 Fire tube6．给水管 Feed pipe7．炉膛 Furnace8．炉墙 Furnace wall9．火侧 Fire side10．水侧 Water side11．燃烧器 Oil burner12．安全阀 Safety valve13．上排污 Upper drain14．下排污 Lower drain15．锅炉皮阀 Mounting valve16．水位计 Water level gauge17．压力表 Pressure gauge18．主汽门 Main steam valve19．玻璃管 Glass tube20．空调装置 Airconditioning plant21．制冷装置 Refrigerating plant22．冰机 Fridge. Machine23．空气压缩机 Air compressor24．造水机 Fresh water generator25．板式冷却器 Plate type cooler26．机舱天车 Engine room crane27．天车导轨 Crane rail28．电磁阀 Solenoid valve29．舵机 Steering gear30．舵承 Rudder bearing carrier31．液压缸 Hydraulic cylinder32．废气涡轮增压器 Exhaust gas turbocharger 33．弹簧阀 Spring loaded valve34．冷凝器 Condenser35．分油器 Oil separator36．轴带发电机 Shaft generator37．焚烧炉 Oil burner38．分油机 Separator39．分离筒 Separator bowl40．配水盘装置 Paring disc device41．转数计 Revolution counter42．控制阀 Control valve43．辅机 Auxiliary machinery44．制冷装置 Refrigerating plant45．海水淡化装置 Sea water desalting plant 46．热交换器 Heat exchanger47．船用气瓶 Marine air bottle48．冷风机 Cooler unit49．防水风门 Fire damper50．气密挡板 Gas tight damper51．排气风机 Exhaust fan52．舱室通风机 Cabin fan53．机舱通风机 Engine room fan54．应急鼓风机 Emergency blower四、阀门(Words about valve)1．吸气阀 Suction valve2．排气阀 Exhaust valve3．控制阀 Control valve4．导阀 Pilot valve5．单向阀 Nonreturn valve6．口琴阀 Flap valve7．调节阀 Regulating valve8．液压阀 Hydraulic valve9．膨胀阀 Expansion valve10．给水阀 Feed valve11．排水阀 Discharge valve12．截止阀 Stop valve13．吹泄阀 Blowoff valve14．空气阀 Air valve15．泄放阀 Drain valve16．止回阀 Check valve17．海底阀 Sea valve18．回流阀 Retune valve19．节流阀 Throttle valve20．进气阀 Inlet valve21．出气阀 Outlet valve22．热力阀 Thermal valve23．中央阀 Center valve24．单向阀 One way valve25．二通阀 Two way valve26．三通阀 Triple valve27．旁通阀 Bypass valve28．换向阀 Changeover valve30．溢流阀 Overflow valve31．自闭阀 Selflocking valve32．针阀 Needle valve33．平衡阀 Balance valve34．循环阀 Circulation valve35．主阀 Main valve36．滑阀 Slide valve37．蝶阀 Butterflyvalve38．截止阀 Shutoffvalve39．闸板阀 Gate valve40．通海阀 Sea suction valve41．吹除阀 Sea chest cleaning valve 42．防浪阀 Storm valve43．舱壁阀 Bulkhead valve44．快关阀 Emergency shut off valve 45．呼吸阀 Breather valve五、泵类(Words about pump)1．电动泵 Motordrivenpump2．柱塞泵 Plunger pump3．叶片泵 Vane pump4．回转泵 Rotary pump5．齿轮泵 Gear pump6．往复泵 Reciprocating pump7．离心泵 Centrifugal pump8．真空泵 Vacuum pump9．螺杆泵 Screw pump10．喷射泵 Ejector pump11．冷却泵 Cooling pump12．淡水泵 Fresh water pump13．海水泵 Sea water pump14．给水泵 Feed water pump15．循环泵 Circulating pump16．锅炉给水泵 Boiler feed pump 17．卫生水泵 Sanitary pump18．压载泵 Ballast pump19．舱底泵 Bilge pump20．污水泵 Sewage pump21．燃油泵 Fuel pump22．高压油泵 High pressure pump 23．低压油泵 Low pressure pump 24．驳运泵 Transfer pump25．增压泵 Booster pump26．消防泵 Fire pump27．通用泵 G.S. pump28．旋涡泵 Regenerative29．蜗壳泵 Volute pump30．导叶泵 Diffuser pump31．单联泵 Simplex pump32．双联泵 Duplex pump33．多联泵 Multiplex pump34．活塞泵 Piston pump35．减摇泵 Antirollpump36．总用泵 General service pump 37．应急消防泵 Emergency fire pump 38．扫舱泵 Stripping pump39．货油泵 Cargo oil pump 40．滑油泵 Lubricating oil pump 六、甲板机械类（Deck machinery）1．锚机 Windlass2．锚机轴 Windlass shaft3．刹车带 Brake lining4．离合器 Clutch5．锚链轮 Anchor Chain wheel 6．轴承瓦 Bearing bush7．轴承盖 Bearing cover8．绞揽机 Capstan9．系揽绞车 Mooring winch 10．卷缆车 Reel 个11．钢丝绳 Wire rope12．卡环 Shackle13．缆绳 Mooring rope14．滑轮 Block15．刹车装置 Brake device 16．制链器 Anchor chain stopper 17．舱盖滚轮 Hatch cover wheel 18．舱盖铰链 Hatch cover hinge 19．液压油缸 Hydraulic jack 20．起货机 Cargo winch21．克令吊 Crane22．生活吊 Accommodation crane 23．吊杆 Derrick boom24．桅杆 Mast25．救生艇 Lifeboat26．艇架 Davit27．艇机 Lifeboat capstan 28．救生筏 Life raft29．救生衣 Life jacket七、工具类(Word about tools) 1．车床 Lathe2．刨床 Planing machine3．钻床 Drill machine4．砂轮机 Grinding machine 5．磨床 Grinder6．铣床 Milling machine7．镗床 Boring machine8．手锤 Engineer’s hammer 9．冲击板手 Impact wrench 10．板手 Spanner11．活络板手 Screw spanner12．梅花板手 Ring spanner13．呆扳手 Open spanner15．套筒板手 Socket spanner16．管子钳 Pipe spanner17．螺丝刀 Screw driver18．钢丝钳 Wire pliers19．尖嘴钳 Long nose pliers20．钢锯 Hack saw21．剪刀 Scissors22．手电筒 Torch23．扁铲(凿子) Chisel24．锉刀 File25．丝攻 Thread tap26．板牙 Thread die27．绞刀 Reamer28．刮刀 Scraper29．油石 Oil stone30．拔子(拉马) Puller31．沙布 Emery cloth32．破布 Rag33．卷尺 Measuring tape34．空心冲 Hole punch35．样冲 Joint punch36．油壶 Oil gun37．牛油枪 Grease gun38．手电钻 Handle drill39．钻头 Drill40．液压千斤 Hydraulic jack.41．塞尺 Feeler gauge42．游标卡尺 Vernier caliper43．外卡尺 Outside calipers44．内卡尺 Inside calipers45．螺纹量规 Screw gauge46．桥规 Bridge gauge47．电焊机 Electrode welding machine 48．气焊机 Gas welding machine 49．电焊钳 Electric welding pliers 50．气割枪 Cutting touch51．电焊条 Electric soldering iron 52．电工刀 Electrician knife53．电笔 Test pen54．剥线钳 Wire stripping pliers 55．圆规 Compass56．量表 Gauge57．拐档表 Crank deflection gauge58．深度规 Depth gauge59．千分表 Micrometer gauge60．台虎钳 Table vice61．柴油 Diesel oil62．滑油 Lubricating oil63．液压油 Hydraulic oil64．重油 Heavy oil65．燃油 Fuel oil66．黄油 Grease67．螺栓 Bolt68．螺帽 Nut69．垫片 Washer70．研磨沙 Grinding sand71．研磨膏 Grinding paste72．石棉板 Asbestos plate73．青壳纸 Fish paper74．盘根 Packing75．细钢丝 Thin steel wire76．密封圈 Rubber seal ring77．塑料管 Plastic pipe78．胶皮管 Rubber hose79．电灯泡 Electric bulb80．工作灯 Working lamp81．插头 Electric plug82．插座 Electric socket.93．喷砂机 Sand blaster outfit94．空气马达 Air motor95 油柜清洁器 Tank cleaning machine96．高压冲水机 High pressure hose for hydraulic 97．真空泵 Vacuum pump98．套筒扳手组 Socket wrench set99．深头套筒 Deep socket wrench100．套筒扳手 Box wrench101 单开口扳手 Single open end wrench102．双开口扳手 Double open end wrench103．转矩扳手 Torque wrench104．电动机扳手 Motor wrench105．侧剪钳 Slide cutting plier106．活节钳 Combination plier107．可调快速扳手 Speed wrench108．螺丝起子 Screwdriver109．偏向螺丝起子 Offset screw110．六角螺帽起子组 Hexagon nut drivers set111．手摇钻 Straight hand drill112．手工锯 Hacksaw frame113．锯片 Hacksaw blade114．砂纸 Silicon paper115．手拉葫芦 Chain block116．高压管 High pressure hose117．液压千金顶 Hydraulic jack118．锤子 Hammer119．平錾 Cold chisel120．活动扳手 Adjustable wrench121．螺丝刀 Screwdriver122．侧剪铗 Side cutting hipper123．螺栓剪 Cable cutter124．敲击管钳 Rap wrench125．砂轮 Grinding wheel126．老虎钳 Utility vise127．直梯 Straight ladder128．踏梯 Step ladder129．平台推车 Platform trunk130．搬平车 Gas cylinder carrier131．给油机 Grease lubricator132．强力油泵 Heavy duty pump oiler133．油壶 Oil jag134．麻花钻 Twist drill135．绞刀 Pin reamer136．旋转中心钻 Rolling center137 ．外径测微计 Outside micrometer with counter 138．六折式尺 Sixfolding rule139．弹性带尺 Convex rule140．不锈钢直尺 Stainless steel straight rule 141．平面规 Surface gauge142．平行直角定规 Precision flat try square 143．温度计 Thermometer八、常用物料(Material in common use)1．阀研磨剂 valve grinding compound2．电焊条 steel electrode3．气焊条 Steel welding wire4．细钢丝绳 Seizing wire5．刚焊条 Steel welding rod6．紫铜管 Copper tube7．乙炔气瓶 Acetylene cylinder8．木屑 Saw dust9．水泥 Cement10．石灰 Lime11．帆布手套 Canvas glove12．垫片 Gasket.13．氧气瓶 Oxygen cylinder14．抹布 Rag15．垫隙片 Shim16．电线 Wire17．电缆 Electric cylinder18．电池 Rag19．灯泡 Bulb20．胶布 Insulating tape21．插头 Plug22．插座 Socket23．保险丝 Fuse24．不锈钢 Stainless steel25．铸铁 Cast iron26．黄铜 Brass27．青铜 Bronze28．铝合金 Aluminium alloy29．橡胶 Rubber30．石棉 Asbestus31．低碳钢 Soft steel32．高碳钢 Highcarbon steel33．合金钢 Alloy steel34．木材 Wood35．塑料 Plastic36．球墨铸铁 Nodular iron九、常用紧固件(Part of fixation in common use)1．螺栓 Bolt2．螺丝 Screw3．螺母 Nut4．方头螺栓 Sq head bolt5．埋头螺栓 Counter sunk head screw6．套筒螺栓 Socket head bolt7．定位螺栓 Set screw8．十字接头 Cross9．锥形销 Taper pin10．锁紧螺母 Lock nut11．六角头螺栓 Hex head bolt十、常用油类(Oil in common use)1．汽油 Gas oil2．煤油 Kerosene3．润滑油 Lubricating oil4．汽缸油 Cylinder oil5．压缩机油 Compressor oil6．齿轮油 Gear oil7．机油 Motor oil8．凡士林 Vaseline9．燃油 Fuel oil10．油脂 Grease11．柴油 Diesel oil十一、常用量词(Quantifier in common use) 1．件，只，个 Piece2．条，张，片 Sheet3．双 Pair4．套，组，副 Set.5．盒 Box6．箱 Case7．瓶 Bottle8．米 Meter9．厘米 Centimeter10．毫米 Millimeter11．公斤 Kilogram12．克 Gram13．公升 Liter14．平方 Square15．袋 Bag16．码 Yard17．吨 Ton18．磅 Pound19．加仑 Gallon20．立方 Cubic十二、国家名称(Name of country)1．中国 China2．美国 American3．日本 Japan4．英国 Britain5．法国 France6．德国 German7．韩国 South Korea8．希腊 Greece9．泰国 Thailand10．印度 India11．挪威 Norway12．俄罗斯 Russia13．新加坡 Singapore14．澳大利亚 Australia15．伊朗 Iran16．丹麦 Denmark17．加拿大 Canada18．丹麦 Denmark19．芬兰 Finland20．巴基斯坦 Pakistan21．意大利 Italy十三、常用缩语(abbreviation in common use)1．主机 M/E2．付机 A/E3．阀 V/V4．泵 P/P5．备车 St/by6．完车 F.W.E.7．前进三 FAHD8．微速后退 D.S.Ast9．前进二 H.Ahd10．高压 H.P.11．低压 L.P.12．重油/柴油 H.O./D.O.13．前后 F/A14．左舷 P: port15．无人机舱 UMS16．自动 Auto17．气缸 Cyl18．燃油柜 19．滑油柜 20．沉淀柜 .21．排出 Disc22．吸入 Suct23．柴油柜 十四、船用动态常用单词(marine tends word) 1．停靠 Alongside2．接近 Approach3．停泊 Berth4．浮筒 Buoy5．码头 Pier6．港口 Port7．移泊 Shift8．航次 Voyage9．试验 Try10．值班 Watch11．航行 Sail十五、船舶机电设备操作词汇(manipulate of marine equipment) 1．调整 Adjust2．压载 Ballast3．转换 Change over4．清洁 Clean5．联接 Connect6．排放压载 Deballast7．放残水 Drain8．卸载 Off9．油漆 Paint10．接通 Put on11．吹灰 Soot blown12．开始 Start13．顶端 Top14．洗 Wash15．吹 Blow16．检查 Check17．铲 Chip18．断开 Cut out19．排放 Discharge20．除垢 Descale21．检验 Examine22．受载 On(load)23．用泵排出 Pump out24．调整 Set25．停止 Stop26．调驳 Transfer27．加满 Top up十六、故障常用单词(words about malfunction)1．失常的 Abnormal2．烧坏 Burn3．堵塞 Clog4．裂缝 Crack5．变形 Deform6．毁坏 Destroy7．磨损 Wear8．出故障 In trouble9．敲击 Knock10．松开 Loose11．不对中 Misalign12．不足的 Insufficient13．失灵 Out of order14．过载 Overload15．过度磨损 Overworn16．尺寸过大 Oversized17．尺寸过小 Undersized18．振动 Vibrate19．不平的 Uneven20．不准确 Inaccurate21．全船断电 Black out22．出故障 Fail23．关掉 Shut off24．弯曲 Bend25．停车 Break drown26．腐蚀 Corrode27．腐蚀的 Corrosive28．损坏 Damage29．有毛病的 Faulty30．有缺陷的 Defective31．破裂 Fracture32．卡住 Jam33．漏泄 Leak34．漏泄的 Leaky35．融化 Melt36．噪声 Noise37．过热 Overheat38．咬住 Seize39．紧的 Tight40．松的 Loosen41．发现 Find42．停止 Stop43．脏的 Dirty44．油污的 greasy45．失效的 ineffective46．椭圆形的 oval47．点不着火 misfire48．接错 misjoin49．放错 misplace50．老化 perish51．麻点 pit52．凸起 ridge53．划伤 score54．拉痕 scuff十七、保养检修常用词汇(Words about maintain and examination) 1．卡死 Blind2．用卡钳量 Caliper3．关闭 Close4．解体 Disassemble5．安装 Fix6．组装 Box up7．检验 Check8．拆卸 Dismantle9．装配 Fit10．紧固 Fasten11．测量 Gauge12．安装 Install13．测量 Measure14．打开 Open15．上油漆 Paint16．换新 Renew17．上紧 Tighten18．洗 Wash19．涂油脂 Grease20．松开 Loosen21．加油 Oil22．检修 Overhaul23．重新组装 Reassemble 24．测取读数 Take reading 25．拧开螺栓 Unbolt26．抽出 Withdraw十九、时间、季节与方向(Time、Season and Direction) 1．星期一 Monday2．星期二 Tuesday3．星期三 Wednesday4．星期四 Thursday5．星期五 Friday6．星期六 Saturday7．星期日 Sunday8．春季 Spring9．夏季 Summer10．秋季 Autumn11．冬季 Winter12．一月 January13．二月 February14．三月 March15．四月 April16．五月 May17．六月 June18．七月 July19．八月 August20．九月 September21．十月 October22．十一月 November23．十二月 December24．小时 Hour25．分钟 Minute26．秒 Second27．月 Month28．天 Day29．夜 Night30．周 Week31．早晨、上午 Morning32．下午 Afternoon33．傍晚 Evening34．正午 Noon35．今天 Today36．昨天 Yesterday37．明天 Tomorrow38．前天 The day before yesterday 39．后天 The day after tomorrow40．本周 This week41．上周 Last week42．下周 Next week43．九月十日 Sep.10 th44．去年 Last year45．明年 Next year46．上周二 Last Tuesday47．下周一 Next Monday48．东 East49．西 West50．南 South51．北 North52．西北 Northwest53．东北 Northeast54．东南 Southeast55．西南 Southwest56．世纪 Century二十、常用词组（Phrases in common use）1 已无法修复 beyond repair2．尺寸过大 oversized3．反应缓慢 slow function4．不正常 out of order5 不合标准 not up to standard6．不准确 inaccurate7．失去作用 out of function8．轧住 seized9．过热 overheated10 过度磨损 ound excessive wear 11．过度磨掉 worn out12．有一点倾斜 a little bit inclined 13．不正常 abnormal14．因过热而损坏 founDestroyed by overheating15．龟裂 chapped16．塌陷 collapsed17．运转失灵 out of operation18．呈椭圆形 oval19．拉痕 scored20．拉毛 scuffed21．变形 deformed22．松动 loose23．油污 greasy24．肮脏 dirty25．咬住 stuck26．挤压 squeezed27．弯曲 bent28．故障 faulty29．损坏 damaged30．破碎成片 broken to pieces31．部分剥离 partly detached32．部分堵塞 partly choked33．剧烈震动 violent vibration 34．烧坏 burnt35．断裂 fractured36．接地 earthed37．敲缸 knocking38．溶化 melted away39．发现泄漏 leaking ( leaky) 40．冻结 stuck fast by icing41．锈蚀 rusty42．失效 ineffective43．故障 out of order44．结霜 frosted45．丢失 lost46．出故障 in trouble47．失灵 out of order48．失灵 out of action49．不一致 out of operation50．错位 out of place二十一、常用动词和例句(Verb in common use and example)1．借 borrow我要向你借这份图纸I want to borrow the drawing from you.我可以向你借这个手锤吗?May I borrow the hammer from you?2．裂 break阀杆断裂了The valve spindle is broken.滚动轴承断裂成碎片了The ball bearing are broken to pieces.3．加强 build up叶轮应该堆焊 The impeller should be built upby welding.4．烧 burn电动机烧了 The motor is burnt.5．进行 carry out应进行负载试验The load test should be carried out.6．吹 blow管子必须用压缩空气吹清The pipe should be blown with compressed air. 7．铸 cast按原样铸造一个 Cast one piece as per sample. 8．引起 cause损坏是有剧烈振动引起的The damage was caused by violent vibration. 9．倒角 chamfer油槽须倒角 Oil groove is to be chamfered.法兰切削后须倒角The flange should be chamfered after being machined.10．换掉 change把它们换掉,否则我拒绝验收Have them changed, otherwise I refuse to accept them.11．龟裂 chap轴瓦上的白合金龟裂了 The white metal onthe bearing bush is chapped.12．核查 check用桥规核查主轴承 Check the main bearingwith bridge gauge.修理前后要核查拐档差Check the crankshaft deflection before andafter repair.13．清洁 clean装前须清洁 Clean it before fit back.14．阻塞 clog燃油滤器阻塞了 The fuel filter is clogged.15．涂漆 coat用红丹涂管子 Coat the pipe with red lead.泵壳里涂防护漆The pump casing is to be coated with antifouling. 16．完成 complete finish你什么时候能完成修理工作?When can you complete (finish) the repair job? 17．连接 connect把电动机和淡水泵连接起来 Connect the motorwith the fresh water pump18．腐蚀 corrode泵壳和叶轮均有腐蚀 The pump casing andimpeller are corroded.19．盖 cover请把所有卸下的部件盖起来Please cover all the removed parts.20．裂二号缸头裂开穿透至冷却水空间No.2 cylinder head is cracked.21．吊 crane把液压马达吊上岸去修理Crane the hydraulic motor ashore for repair. 22．割 cut把底座割掉Cut off the bedplate.23．损坏 damage滚动轴承严重损坏The ball bearings are seriously damaged.24．脱落 detach白合金部分脱落了The white metal is partly detached.25．查看 detect查看氟里昂系统有无泄漏Detect the Freon system for leakage.26．解体 disassemble解体,清洁并检查高压油泵Disassemble, clean and check the H.P. fuel pump. 27．脱开 disconnect把起动空气管脱开Disconnect the starting air pipe.将发电机与原动机脱开。

轮机英语- 轮机工程原理（英文版）Principles of Marine Engineering2010. 10ContentsContents (2)1 Main propulsion plant (篇标题) (3)1.1 Ships and machinery (章标题) (3)1.2 Diesel engine (9)1.3 Shaft and propellers (46)2 Marine auxiliary machinery (55)2.1 boilers (55)2.2 Pumps (55)2.3 Refrigeration, air conditioning and ventilation (55)2.4 Pollution prevention devices (55)2.5 Centrifugal separator and fresh water generator (55)2.6 Deck machinery (55)3 Electrical equipment and automatic control (56)3.1 Alternating current generators (56)3.2 Main switchboard and distribution system (56)3.3 Marine electrical equipment (56)3.4 Marine automatic control (56)4 Watch keeping and equipment operation (57)4.1 operation procedures (57)4.2 Safety operation (57)4.3 Stores and spare parts (57)4.4 Shipp repair and docking (57)4.5 Pollution prevention operation and Port State Control (57)5 International conventions and regulations (58)5.1 STCW (58)5.2 MAPROL (58)5.3 SOLAS (58)5.4 ISM (58)5.5 ISPS (58)6 Marine business writing (59)6.1 Engine log book (59)6.2 Repair list (59)6.3 Store order and spare parts requisition form (59)6.4 Accident report (59)6.5 Engineer’s reports, letters, faxes and emails (59)Index ............................................................................................................... 错误！未定义书签。

yacht : [jɔt]n.快艇，(竞赛用的)帆船，游艇general cargo ship: 杂货船refrigerator ship :冷藏船cruiser n．游船dry bulk carrier 干散货船passenger liner 旅客班轮cruiser n．游船air cushion craft 气垫船barge-carrier 载驳货船bulk-carrier散货船catamaran 双体船container ship 集装箱船chemical carrier 化学品（运输船）diesel boa柴油机船dry cargo ship 干货船electric motor ship 电动机船ferry 渡船freighter (cargo ship) 货船fire boat 消防船hydrofoil craft水翼船Ice-breaker破冰船life boat 救生船LNG carrier（liquefied natural gas carrier）液化天然气（运输）船multi-purpose ship多用途船oil barge 油驳ore carrier（ore ship ）矿砂船passenger liner 定期客船pilot boat引航船roll - on / roll - off ship (Ro-Ro ship) 滚装船reefer ( refrigerator ship )冷藏船salvage vessel救助船scientific surveying ship科研考察船semi-container ship半集装箱船semisubmersible drilling vessel半潜式钻井船specialized duty vessel专业船tramp不定期货轮tug拖船10．商船：merchant ship11．油船：tanker 12．散货船：bulk carrier2.船舶主要部分船首：bow 船尾stern 左舷：port side 右舷：starboard side 艏楼：forecastle艉楼：poop 上层建筑：superstructure肋骨：frame二层甲板：tween deck机舱：engine room 水密分舱：watertight compartment 艏尖舱：fore peak tank艉尖舱：after peak tank 双层底舱：double bottom tank 制链器：chain stopper锚链舱：chain locker锚链管：chain pipe锚机滚筒：chain cable barrel锚链筒：hawse pipe标准罗经：standard compass磁罗经：magnetic compass主操舵罗经：main rudder compass 陀螺罗经：gyrocompass推进器：propeller3.船用柴油机工作原理1．船用柴油机：marine diesel2．内燃机：internal combustion engine3．气缸：cylinder 4．活塞：piston 5．细雾状燃油：fine spray of fuel6．曲轴：crankshaft7．推进器：propeller 8．循环：cycle 9．四冲程柴油机：four-stroke diesel10．进气：fresh air11．压缩：compession 12．膨胀：expansion13．排气：exhaust14．二冲程柴油机：two-stroke diesel17．下死点：B.D.C15．燃烧室：combustion chamber 16．工作原理：principle of operation 18．排气口：exhaust port 19．残留废气：residual exhaust 20．上死点：T.D.C21．燃油喷射：fuel injection 22．进气口：inlet port 23．工作冲程：working stroke24．减速齿轮箱：reduction gearbox25．交流发电机：alternator26．连杆：connecting rod 27．扫气口：scanvenging port4.船用柴油机的种类1.船用发动机：Marine engine2.紧凑：compact3.柴油机：diesel4．蒸汽机：steam turbine 5．气轮机：gas turbine6．内燃机：internal combustion engine7．输出功率：output power 8．制动马力：brake horsepower9．螺旋桨：propeller 13．燃油消耗率：fuel comsuption 14．锅炉：boiler15．有吸引力的：attractive16．集装箱船：container ship17．衰变：decay 18．通过比较：by comparision19．限制，约束：restriction20．叶片：blade21．有效马力：effective horsepower22．放射性的：radioactive23．船用核装置：marine nuclear plant24．货油泵：cargo oil pump固定件：fixed part 运动件：moving part 曲柄箱：crankcase缸套和衬套：cylinder and liner 气缸盖：cylinder cover 活塞：pistion气缸体：cylinder block 活塞头：piston crown 活塞杆：piston rod十字头：cross 连杆：connecting rod 主轴承：main bearing轴向推力：axial push端塞螺栓：side-chock bolt 从动轴：driven shaft 推力块：thrust block扫气箱：scavenging air box机座：bedplate 机架：frame冷却水套：cooling jacket 21．燃烧室：combustion chamber22．排气阀：exhaust valve23．燃油阀：fuel valve 24．起动阀：starting valve25．安全阀：safety valve26．示功器旋塞：indicator cock 27．冷却腔：cooling chamber28．活塞裙：piston skirt29．活塞环：piston ring30．垫圈：rubber ring31．往复运动：reciprocating movement 32．工作行程：power stroke6.燃油系统燃油系统：fuel oil system 运行和维护：operation and maintainence残碳值：carbon residues 燃油粘度：fuel oil＇s viscosity十六烷值：cetane number 热值：calorific value 闪点：flash point凝固点：setting point 比重：gravity 10.含水量：water content11．机械杂度：mechanical impurity12．重油：heavy fuel 13．渣油：residual oil14．沉淀柜：settling tank15．燃油舱：bunker tank16．日用柜：daily service tank17．细滤器：fine filter18．压力调节阀：pressure regulating valve19．针阀：needle vavle20．低油位报警：low tank level level alarm21．输送泵：transfer pump22．三通阀：three-way valve23．喷射泵：injection pump 24．过滤器：stainer7.润滑系统润滑油膜：lubricating oil film 运动件：moving part 运动条件：operation conditions油冷式活塞：oil cooled piston抗氧化：resistance to oxidation总量损耗系统：total loss system feeding循环式系统：circulating system传动装置：running gear燃烧室：combustion space活塞顶：piston crown活塞环：piston ring衬套壁：liner wall运动方向的改变：reversal of direction of motion机械注油器：mechanical lubricator曲轴箱：crankcase轴承：bearing17．活塞杆：piston rod 18．辅助设备：auxiliary equipment 19．泵：pump20．离心分离机：centrifuge8.水冷却系统燃油喷射阀fuel injector valve排气阀exhaust valve起动空气阀starting air valve机械强度mechanical strength内部管道internal passage热交换器heat exchanger气缸套冷却水循环泵cylinder liner circulating pump涡轮增压器turbo-blower闭式系统closed system开式系统open system压力水柜pressure tank海水循环式冷却器sea water circulated cooler heat exchanger汽蚀效应cavitation effect气囊steam pocket放气口air lock透气管ventilation pipe支路branch可视式流量计visual flowmeter喷嘴积碳nozzle deposited carbon滑油冷却器lubricating oil cooler盲板法兰blind-flange9.舱底和压载系统舱底水：bilge water 压载水：ballast water 相互连接：interconnec t涨水，进水：flood 在船外，到舷外：overboard 水密舱室：watertight compartment应急舱底水泵：emergency bilge pump 替换物，选择对象：alternative引水装置：priming device 到某种程度：to some extent 调节船舶吃水差：trim the vessel 切换阀箱：change-over chest10.管路系统发证机构：certifying authority铸铁：cast iron冲击载荷：shock loading易碎性：brittle nature 循环热处理：cyclic heat treatment低碳钢：mild steel气密结构：gastight structure热膨胀：thermal expansion 锅炉水舱柜：boiler feed water tank贯通配件：through fitting隔离空舱：cofferdam船体变形：deflection of ship construction1．safety valve（安全阀）2．steam stop valve（蒸汽截止阀）3．starting valve（起动阀）4．indicator cock（示功阀，示功考克）5．governing valve（调速阀）6．by-pass valve（旁通阀）7．main stop valve（主截止阀）8．hull valve（船体阀）9．flushing valve（冲洗阀）10．vent valve（排气阀）11．suction valve（进气阀）12．angle valve（角阀）13．automatic valve（自动阀）14．pressure valve（压力阀）15．quick-closing valve（速闭阀）16．self-closing valve（自闭阀）17．air filter（空气过滤器）18．coarse filter（粗滤器）19．fine filter（细滤器）20．heating circulating valve（加热循环阀）11.船用泵容积式泵：displacement pump 离心泵：centrifugal pump往复泵：reciprocating pump叶片泵：vane pump齿轮泵：gear pump旋转泵：rotary pump离心力：centrifugal force轴向的：axial flow涡轮，涡轮机：turbine自吸式：self-priming啮合齿轮：meshing gear蒸汽喷射器：steam ejector舵机液压系统：steering gear hydraulic system人字齿：double helical tooth大气压：atmospheric pressure立式泵：vertical pump12.舵机舵机：steering gear船级社：classification society转舵能力：steering capacity舵叶：rudder船舶吃水：ship’s draught驾驶台：bridge故障：trouble独立的：independent液压伺服马达：hydraulic telemotor舵机室：steering gear room舵柱：rudder stock液压油缸：hydraulic cylinder液压泵：hydraulic pump撞杆：ram舵角信号：signal of rudder angle13.甲板机械甲板机械：deck machinery克令吊：crane日常检验：routine checking锚泊设备：anchor arrangement 集装箱吊装设备厂：container handling facility原动机：prime mover装卸能力：handling capacity多旋转吊杆系统：multiwinch slewing derrick system安全工作负载：safe working load绞车卷筒：winch barrel or drum吊杆式起货装置：derrick crane system14.推进装置直接传动：direct drive推进效率：propulsion efficiency轴系：shaft system旋转方向：rotating direction齿轮传动：gear drive减速齿轮箱：reduction gear box减速装置：reduction arrangement双桨：twin-screw双舵：twin-rudde r双机并车：twin-engine incorporation多级：multi-stage带倒车离合器的减速：reduction with an astern clutch机舱：engine space挠性联轴节：flexible coupling安装误差：installation error可调螺旋桨：VPP or CPP固定螺旋桨：fixed pitch propeller定位：keep station15.轴系及设计程序传动轴系：transimission shafting system艉轴：stern shaft螺旋桨轴：screw shaft中间轴：intermediate shaft法兰联轴节：flange coupling可拆联轴节：removable coupling 隔舱填料函：compartment stuffing box推力环：thrust ring中空轴：hollow shaft轴倾斜度：shaft rake动态特性：dynamic characteristic扭振：torsional vibration纵振：longitudinal vibration回转振动：whirling vibration振动计算：vibration calculation 螺旋桨桨叶：propeller blade16.船舶设计与造船工程师造船工程师：naval architect造船工程学：naval architecture力矩平衡：moment balance重力平衡：weight balance轴马力：shaft horsepower净登记吨位：net register tonnage总吨位：gross tonnage扣除空间：deductible space流体力学：fluid mechanics结构强度：structural strength重货：high-density cargo轻货：low-density cargo港口税：harbor due母型船：projected ship重心：centers of gravity纵倾和稳性：trim and stability肋骨尺度：frame dimension外板厚度：plate thickness零件图：detail drawing总图：general drawing17.造船过程1.（船舶）下水滑道：launching way2．初步设计：preliminary design3．合同设计：contract design 4．详细设计：detail design5．运作要求：operational requirement6．缩尺船模（模型）：scale model7．成组建造技术：group technology to shipbuilding 8．大规模生产：mass production 9．任务系统：mission system10．交船日：delivery date 11．性能要求：performance requirements12．计划与调度：planning and scheduling13．个别零件：individual parts14．干船坞：dry dock15．投标过程：bidding process 16．船体分段：hull block17．装配线：assembly line18．概念设计：concept design18.船厂设施building period建造周期assembly line 装配（流水）线sloping shipway 有坡度船台，滑道building basin 船台floating dry dock 浮船坞engineering workshop轮机车间erection shop 装配车间fitting out quay舾装码头pumping station泵站，动力室repair quay 修船码头ship drawing office 船舶设计室20.船舶下水与舾装横向下水：sideway launching下水架：launching cradle滑道：standing way滑板：sliding way边墩：side support下水扳机：launching trigger局部压力：local pressure限制水域：restricted waterway减速力：retarding force阻力锚：drags21.适航1.试验大纲：sea trial programmers2．测速区：measured mile course3．重新试航：re-trial run4．性能试验：performance test5．动力装置：power plant6．抛锚试验：anchor-heaving trial7．适航性能：sea-keeping performance8．回转试验：turning trial9．潮汐效应：tidal effect10．逐级加速试航：Progressive speed trial11．续航力试验：endurance trial12．船舶试验协议：Protocol of T rials of the ship13．船舶设备清单：Inventory of the equipment of the vessel14．消耗品储备协议：Protocol of Stores of Consumable Nature15．完工图：finished drawings and plans16．交船：delivery of the vessel23.船级社1．合同前服务：pre-contract service2．提交检验申请：submit survey application3．申请评审及签署检验服务协议：aplication reviewing & survey agreement4．船舶审图及确定船用产品持证清单：drawing approval & required marine products list舶开工前检查：inspect before steel-cutting6．焊接工艺认可：welding technology approval7．焊工资格：welder qualification8．建造检验标准：standard of construct survey9．分段检验：structure inspection10．结构装配及焊接：structure assemble & welding11．安装主辅机、舵及轴系：installation of main engine, auxiliary mechinery & shafting 12．船台上或船坞内装配检验：assemble inspection on slipway or dock13．分段合拢检验：inspection of structure assemble14．焊缝检验：inspection of welding 15．无损探伤检验：NDT16．密性试验：tightness test17．船舶下水：lauching18．系泊试验：mooring trial19．航海试验：sea trial20．签发短期证书：issuance of interim certificates21．签发全期法定证书：Issuance of Full-Term Statutory Certificates22．CCS船舶录：Register of Ships by CCS23．签发全期船级证书：Issuance of Full-Term Class Certificates24．船级委员会：Class Committee。

1.H e a v e t h e h e a d/s t e r n l i n e.绞头缆/尾缆。

2 绞紧横缆和倒缆。

3.Stop heaving the head/stern line and the spring. 停绞头/尾缆和倒缆。

4.Hold the head/stern line and the spring. 拉头/尾缆和倒缆。

5.Make fast the head/stern line and the spring. 挽牢头/尾缆和倒缆。

6. 自左舷松下一根引缆给带缆船。

7.Lower one slip wire to the mooring boat from starboard side. 自右舷松下一根回头缆给带缆船。

8.Walk out the port anchor chain on the water surface. 松出左锚锚链到水面。

9.Unshackle the port anchor from the chain before three o'clock afternoon. 下午3点以前把左锚从锚链上卸下来。

10.Heave the port/starboard head/stern line. 绞直左/右舷头尾/缆。

11.Give a good rope to the tug boat from starboard/port side. 从右/左舷卸下一个质量好的缆绳给拖船。

12.You must make the tug line fast on the bitts. 你必须要把拖缆牢固地挽在缆桩上。

13.Slack away the head/stern/ tug line. 松出头/尾/拖缆。

14.Let go the head/ stern/tug line. 解头/尾/拖缆。

15.Let go the spring /the breast line. 解到/横缆。