电感全系列规格书(中性)

目录1 概述 (2)2 产品型号说明 (3)3 功能特点 (3)4 技术参数 (5)5 结构 (6)6 电气原理 (7)7 自动调谐控制器 (10)7.1 概述 (10)7.2 组成 (10)7.3 主要功能 (10)7.4 使用方法 (13)7.5 运行维护注意事项 (21)8 自动控制屏 (21)9 使用须知 (21)10 消弧限压装置的操作注意事项 (24)11 订货须知 (25)12 附录 (27)1 概述中性点接地方式关系到电力系统的运行可靠性。

目前我国6～66kV电网，一般采用中性点不接地、低阻接地或经消弧线圈接地方式。

对于中性点不接地系统，当系统发生单相接地故障时，系统可带故障运行2小时，可相对提高系统的供电可靠性。

但当系统的接地电容电流较大时，接地处引起的电弧就难以自行熄灭，甚至可能出现间歇性电弧，从而产生谐振过电压，对电网带来不利影响。

采用低电阻接地，可限制弧光接地过电压，对设备绝缘等级要求较低，不足之处在于系统中任何单相接地故障都跳闸，导致跳闸率过高；同时，系统单相接地故障时故障点接地电流很大，对电网带来许多不利影响。

为此，我国电力行标DL/T620－1997中规定：6～10kV不直接连接发电机的系统和35kV、66kV系统，当单相接地故障电容电流超过下列数值又需在接地故障条件下运行时，应采用消弧线圈接地方式：6～10kV架空线路构成的系统和所有35kV、66kV系统，10A；6～10kV 电缆线路构成的系统，30A。

消弧线圈的主要作用是在系统发生单相接地故障时产生电感电流以补偿电网电容电流，使故障点残流变小，达到自动熄弧、消除故障的目的，具有减少跳闸次数、降低接地故障电流的优点，使系统能够在故障条件下继续运行一段时间，为找到故障线路争取时间。

BZXH-01-Z型消弧线圈调谐及选线控制成套装置用于中性点经调匝式消弧线圈接地的系统中，可自动跟踪系统运行方式的改变，调整消弧线圈的档位改变补偿电感电流，使系统残流在设定值之内，当系统发生瞬时性单相接地故障时自动补偿系统电容电流，使故障自动恢复；对非瞬时性单相接地故障，控制消弧线圈进行补偿，同时用最短的时间正确判断接地线路，将故障线路切除，从而提高系统的供电可靠性。

Multilayer Chip Ceramic Inductor – SDCL-D SeriesOperating Temp. : SDCL1005 series: -55℃~+125℃SDCL1608 series: -40℃~+85℃FEATURES●Monolithic structure for high reliability● High self-resonant frequency● Excellent solderability and high heat resistanceAPPLICATIONS●RF circuit in telecommunication and other equipmentsPRODUCT IDENTIFICATIONSHAPE AND DIMENSIONSUnit: mm [inch]Type L W T a SDCL1005[0402]1.0±0.15 [.039±.006]0.5±0.15 [.020±.006]0.5±0.15 [.020±.006]0.25±0.1 [.010±.004]Fig.1SDCL1608 [0603] 1.6±0.15 [.063±.006]0.8±0.15 [.031±.006]0.8±0.15 [.031±.006] 0.3±0.2 [.012±.008]Fig.21.65±0.15 [.065±.006]②External Dimensions (L×W) (mm)1005 [0402] 1.0×0.5 1608 [0603] 1.6×0.8 ① TypeSDCL Chip Ceramic Inductor③ Material Code C ④ Nominal InductanceExample Nominal Value 3N9 3.9nH 10N 10nH R10 100nH※R=小数点，N=nH ⑤Inductance Tolerance S ±0.3nH J ±5%K ±10% ⑥Packing T Tape & Reel⑧Hazardous Substance Free ProductsFSDCL ① 1608② C ③ 10N ④ J ⑤ T⑥ D ⑦ F ⑧ ⑦ Internal Code DFig.1Fig.2规格特性 SPECIFICATIONSSDCL1005-D SeriesPart NumberInductanceMin.QualityFactor L,Q Test Freq. L/Q Typical Q @ Freq. (MHz)Min.Self-resonantFrequency Max. DCResistanceMax. Rated Current1008001000Units nH - MHz - MHz Ω mA Symbol L Q Freq Q S.R.F DCR IrSDCL1005C1N0STDF 1.0±0.3 8 100 11 34 36 10000 0.10 400 SDCL1005C1N1STDF 1.1±0.3 8 100 11 34 36 10000 0.10 400 SDCL1005C1N2STDF 1.2±0.3 8 100 11 34 36 10000 0.10 400 SDCL1005C1N3STDF 1.3±0.3 8 100 11 34 36 10000 0.10 400 SDCL1005C1N5STDF 1.5±0.3 8 100 11 34 36 6000 0.10 300 SDCL1005C1N6STDF 1.6±0.3 8 100 11 32 35 6000 0.10 300 SDCL1005C1N8STDF 1.8±0.3 8 100 11 30 34 6000 0.10 300 SDCL1005C2N0STDF 2.0±0.3 8 100 10 29 33 6000 0.20 300 SDCL1005C2N2STDF 2.2±0.3 8 100 10 29 33 6000 0.20 300 SDCL1005C2N4STDF 2.4±0.3 8 100 10 29 32 6000 0.20 300 SDCL1005C2N7STDF 2.7±0.3 8 100 10 29 32 6000 0.20 300 SDCL1005C3N0STDF 3.0±0.3 8 100 10 29 32 6000 0.20 300 SDCL1005C3N3STDF 3.3±0.3 8 100 10 29 32 6000 0.20 300 SDCL1005C3N6STDF 3.6±0.3 8 100 10 28 31 4000 0.20 300 SDCL1005C3N9STDF 3.9±0.3 8 100 10 28 31 4000 0.20 300 SDCL1005C4N3STDF 4.3±0.3 8 100 10 28 31 4000 0.20 300 SDCL1005C4N7STDF 4.7±0.3 8 100 10 28 31 4000 0.20 300 SDCL1005C5N1STDF 5.1±0.3 8 100 10 28 30 4000 0.30 300 SDCL1005C5N6STDF 5.6±0.3 8 100 10 28 30 4000 0.30 300 SDCL1005C6N2STDF 6.2±0.3 8 100 10 27 30 3900 0.30 300 SDCL1005C6N8□TDF 6.8 8 100 10 27 30 3900 0.30 300 SDCL1005C7N5□TDF 7.5 8 100 10 27 30 3700 0.40 300 SDCL1005C8N2□TDF 8.2 8 100 10 27 30 3600 0.40 300 SDCL1005C9N1□TDF 9.1 8 100 10 27 30 3400 0.40 300 SDCL1005C10N □TDF 10 8 100 10 27 30 3200 0.40 300 SDCL1005C12N □TDF 12 8 100 10 26 29 2700 0.50 300 SDCL1005C15N □TDF 15 8 100 10 26 28 2300 0.50 300 SDCL1005C18N □TDF 18 8 100 10 25 27 2100 0.60 300 SDCL1005C20N □TDF 20 8 100 10 25 26 2000 0.60 300 SDCL1005C22N □TDF 22 8 100 10 25 25 1900 0.60 300 SDCL1005C27N □TDF 27 8 100 10 25 23 1600 0.70 300 SDCL1005C33N □TDF 33 8 100 10 22 22 1300 0.80 200 SDCL1005C39N □TDF 39 8 100 10 22 19 1200 1.00 200 SDCL1005C43N □TDF 43 8 100 10 21 16 1100 1.10 200 SDCL1005C47N □TDF 47 8 100 10 21 16 1000 1.10 200 SDCL1005C56N □TDF 56 8 100 10 18 13 750 1.20 200 SDCL1005C68N □TDF 68 8 100 10 18 9 750 1.40 180 SDCL1005C82N □TDF 82 8 100 10 13 - 750 2.40 150 SDCL1005CR10□TDF 100 8 100 10 12 - 700 2.60 150SDCL1005CR12□TDF 120 8 100 10 - - 600 2.80 150SDCL1005CR15□TDF 150 8 100 10 - - 550 3.20 100 SDCL1005CR18□TDF 180 8 100 10 - - 500 3.70 100 SDCL1005CR22□TDF 220 8 100 12 - - 450 4.00 100 SDCL1005CR27□TDF 270 8 100 12 - - 400 4.50 100 SDCL1005CR30□TDF 300 6 50 12 - - 350 7.00 50 SDCL1005CR33□TDF 330 6 50 8 - - 350 7.00 50 SDCL1005CR36□TDF 360 6 50 8 - - 300 7.50 50※□: Please specify the inductance tolerance code (J=±5%, K=±10%). The product with tolerance less than ±5%, ±10% is also available. Please contact your local sales.SPECIFICATIONS SDCL1608-D SeriesPart Number InductanceMin.QualityFactorL,Q TestFreq.L/Q Typical Q @ Freq. (MHz)Min.Self-resonantFrequencyMax. DCResistanceMax.RatedCurrent 100800 1000Units nH - MHz - MHz ΩmASymbol L Q Freq Q S.R.F DCR IrSDCL1608C1N0STDF 1.0±0.3 8 100 13 70 80 10000 0.05 500 SDCL1608C1N2STDF 1.2±0.3 8 100 13 60 70 10000 0.05 500 SDCL1608C1N5STDF 1.5±0.3 8 100 13 47 68 6000 0.10 500 SDCL1608C1N8STDF 1.8±0.3 8 100 13 45 61 6000 0.10 500 SDCL1608C2N2STDF 2.2±0.3 8 100 13 45 60 6000 0.10 500 SDCL1608C2N7STDF 2.7±0.3 10 100 13 44 55 6000 0.12 500 SDCL1608C3N3STDF 3.3±0.3 10 100 13 43 50 6000 0.15 500 SDCL1608C3N9STDF 3.9±0.3 10 100 13 43 50 6000 0.16 500 SDCL1608C4N7STDF 4.7±0.3 10 100 13 43 50 6000 0.20 500 SDCL1608C5N6STDF 5.6±0.3 10 100 14 42 48 5000 0.25 500 SDCL1608C6N8□TDF 6.8 10 100 1443 50 5000 0.30 500 SDCL1608C8N2□TDF 8.2 10 100 1443 48 4500 0.35 500 SDCL1608C10N□TDF 10 12 100154550 3500 0.40 300 SDCL1608C12N□TDF 12 12 100184850 3000 0.45 300 SDCL1608C15N□TDF 15 12 100184850 2300 0.50 300 SDCL1608C18N□TDF 18 12 100164851 2200 0.55 300 SDCL1608C22N□TDF 22 12 100164548 2000 0.60 300 SDCL1608C27N□TDF 27 12 100164545 1700 0.65 300 SDCL1608C33N□TDF 33 12 100164541 1500 0.70 300 SDCL1608C39N□TDF 39 12 100174048 1400 0.70 300 SDCL1608C47N□TDF 47 12 100173535 1200 0.70 300 SDCL1608C56N□TDF 56 12 100173530 1100 0.75 300 SDCL1608C68N□TDF 68 12 100173020 900 0.85 300 SDCL1608C82N□TDF 82 8 1001522 - 800 1.00 300 SDCL1608CR10□TDF 100 8 1001516 - 700 1.20 300 SDCL1608CR12□TDF* 120 8 50 15 - - 600 1.40 200 SDCL1608CR15□TDF* 150 8 50 15 - - 500 1.60 200 SDCL1608CR18□TDF* 180 8 50 15 - - 400 1.90 200 SDCL1608CR22□TDF* 220 8 50 15 - - 350 2.40 200 SDCL1608CR27□TDF* 270 8 50 16 - - 350 2.60 150 SDCL1608CR33□TDF* 330 8 50 16 - - 350 2.80 150 SDCL1608CR39□TDF* 390 8 50 16 - - 300 3.20 150 SDCL1608CR43□TDF* 430 8 50 16 - - 280 3.40 150 SDCL1608CR47□TDF* 470 8 50 15 - - 250 3.60 150 SDCL1608CR56□TDF* 560 8 50 15 - - 250 4.00 100 SDCL1608CR68□TDF* 680 8 50 15 - - 250 4.50 100※□: Please specify the inductance tolerance code (J=±5%, K=±10%). The product with tolerance less than ±5%, ±10% is also available. Please contact your local sales.※*: The length: 1.65±0.15mm, for others: 1.60±0.15mm.TYPICAL ELECTRICAL CHARACTERISTICSSDCL1005-D TYPE SDCL1005-D TYPEFrequency(MHz)110I n d u c t a n c e (n H )Frequency(MHz)QSDCL1608-D TYPE SDCL1608-D TYPEFrequency(MHz)110I n d u c t a n c e (n H )Frequency(MHz)Q。

Wire Wound SMD Power Inductors – SWPA SeriesOperating temperature range: -40℃~+125℃ (Including self-heating)FEATURES● Magnetic-resin shielded construction reduces buzz noise to ultra-low levels● Metallization on ferrite core results in excellent shock resistance and damage-free durability ● Closed magnetic circuit design reduces leakage flux and Electro Magnetic Interference (EMI) ● 30% higher current rating than conventional inductors of equal size ● Takes up less PCB real estate and save more powerAPPLICATIONS● Smart phone, smart TV, set top box, notebook ● Car navigation systems, telecomm base stations ● VR, AR ● LED lightingPRODUCT IDENTIFICATIONSWPA3012 S 1R0 N T□□□① ② ③ ④ ⑤ ⑥ ⑦②External Dimensions (L×W×H) [mm] 252010 2.5×2.0×1.0 252012 2.5×2.0×1.2 3010 3.0×3.0×1.03012 3.0×3.0×1.2 3015 3.0×3.0×1.5 4010 4.0×4.0×1.0 4012 4.0×4.0×1.2 4018 4.0×4.0×1.8 4020 4.0×4.0×2.0 4026 4.0×4.0×2.6 4030 4.0×4.0×3.0 5012 5.0×5.0×1.2 5020 5.0×5.0×2.0 5040 5.0×5.0×4.0 6020 6.0×6.0×2.0 6028 6.0×6.0×2.8 6040 6.0×6.0×4.0 6045 6.0×6.0×4.5 8040 8.0×8.0×4.0 8050 8.0×8.0×5.0 8060 8.0×8.0×6.08065 8.0×8.0×6.5 ① Type SWPAWire Wound SMD Power Inductor③ Feature TypeS Standard ④ Nominal InductanceExample Nominal Value1R0 1.0μH 100 10μH⑤ Inductance ToleranceK ±10%M ±20% N ±30% ⑥ PackingTTape Carrier Package⑦ Design Code □□□Standard product is blankFig.1 Fig.2Unit: mmSeriesShapeABCD E Fa Typ.b Typ.c Typ.SWPA252010S Fig.1 2.5±0.1 2.0±0.1 1.0 Max. 2.0±0.20.80±0.20.80±0.2 0.80 0.85 2.0 SWPA252012S Fig.1 2.5±0.1 2.0±0.1 1.2 Max. 2.0±0.20.80±0.20.80±0.2 0.80 0.85 2.0 SWPA3010S Fig.2 3.0±0.2 3.0±0.2 1.0 Max. 2.5±0.20.75±0.2 1.5±0.2 1.5 0.8 2.7 SWPA3012S Fig.2 3.0±0.2 3.0±0.2 1.2 Max. 2.5±0.20.75±0.2 1.5±0.2 1.5 0.8 2.7 SWPA3015S Fig.2 3.0±0.2 3.0±0.2 1.5 Max. 2.5±0.20.75±0.2 1.5±0.2 1.5 0.8 2.7 SWPA4010S Fig.2 4.0±0.2 4.0±0.2 1.0 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4012S Fig.2 4.0±0.2 4.0±0.2 1.2 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4018S Fig.2 4.0±0.2 4.0±0.2 1.8 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4020S Fig.2 4.0±0.2 4.0±0.2 2.0 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4026S Fig.2 4.0±0.2 4.0±0.2 2.6 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4030S Fig.2 4.0±0.2 4.0±0.2 3.0 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA5012S Fig.3 5.0±0.2 5.0±0.2 1.2 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA5020S Fig.3 5.0±0.2 5.0±0.2 2.0 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA5040S Fig.3 5.0±0.2 5.0±0.2 4.0 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA5045S Fig.3 5.0±0.2 5.0±0.2 4.5 Max. 4.0±0.2 1.30±0.2 2.5±0.2 2.3 1.4 4.2 SWPA6020S Fig.2 6.0±0.3 6.0±0.3 2.0 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA6028S Fig.2 6.0±0.3 6.0±0.3 2.8 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA6040S Fig.2 6.0±0.3 6.0±0.3 4.0 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA6045S Fig.2 6.0±0.3 6.0±0.3 4.5 Max.4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.75.7 SWPA8040S Fig.2 8.0±0.3 8.0±0.3 4.2 Max.6.3±0.3 2.00±0.3 4.0±0.3 3.8 2.27.5SWPA8050S Fig.3 8.0±0.3 8.0±0.3 5.0 Max. 6.3±0.3 2.00±0.3 4.0±0.3 3.8 2.2 7.5 SWPA8060S Fig.3 8.0±0.3 8.0±0.3 6.0 Max 6.3±0.3 2.00±0.3 4.0±0.3 3.8 2.2 7.5 SWPA8065S Fig.3 8.0±0.3 8.0±0.3 6.5 Max.6.3±0.32.00±0.34.0±0.3 3.8 2.2 7.5SHAPE AND DIMENSIONS SWPA252010S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max. Typ.Min. Max. Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCRS.R.F Isat Irms SWPA252010SR47NT 0.47±30% 0.056 0.047206 2.50 3.35 2.35 2.56 SWPA252010SR56NT 0.56±30% 0.072 0.060160 2.90 3.20 2.00 2.18 SWPA252010SR68NT 0.68±30% 0.074 0.062129 2.20 2.75 2.00 2.18 SWPA252010S1R0NT 1.0±30% 0.1080.090100 1.85 2.20 1.65 1.80 SWPA252010S1R5NT 1.5±30% 0.182 0.15281 1.80 2.10 1.30 1.42 SWPA252010S2R2NT 2.2±30% 0.209 0.17461 1.20 1.60 1.20 1.31 SWPA252010S3R3MT 3.3±20% 0.328 0.27347 1.05 1.30 0.90 0.98 SWPA252010S4R7MT 4.7±20% 0.563 0.46942 0.95 1.15 0.70 0.76 SWPA252010S5R6MT 5.6±20% 0.563 0.46935 0.80 0.95 0.73 0.80 SWPA252010S6R8MT 6.8±20% 0.896 0.74731 0.78 0.92 0.59 0.64 SWPA252010S100MT 10±20% 1.092 0.91027 0.65 0.78 0.50 0.55SWPA252012S SeriesPart NumberInductance DC Resistance Self-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH Ω MHz A A Symbol L DCR S.R.F Isat IrmsSWPA252012SR47NT 0.47±30% 0.0610.047160 3.82 4.27 2.15 2.34 SWPA252012SR68NT 0.68±30% 0.0740.057140 3.28 3.68 1.95 2.13 SWPA252012S1R0NT 1.0±30% 0.0900.069110 2.59 2.90 1.93 2.10 SWPA252012S1R2NT 1.2±30% 0.1290.099100 2.38 2.67 1.46 1.59 SWPA252012S1R5MT 1.5±20% 0.1470.11397 2.24 2.51 1.40 1.53 SWPA252012S1R5NTY01 1.5±30% 0.1300.10 63 1.80 2.00 1.45 1.58 SWPA252012S2R2MT 2.2±20% 0.2160.16669 1.85 2.07 1.15 1.25 SWPA252012S2R2NTY02 2.2±30% 0.1530.11853 1.55 1.75 1.30 1.42 SWPA252012S2R7MT 2.7±20% 0.2390.18463 1.72 1.92 1.09 1.19 SWPA252012S3R3MT 3.3±20% 0.2640.20362 1.61 1.80 1.04 1.13 SWPA252012S3R6MT 3.6±20% 0.3480.26853 1.46 1.64 0.90 0.98 SWPA252012S4R3MT 4.3±20% 0.3770.29051 1.37 1.53 0.87 0.95 SWPA252012S4R7MT 4.7±20% 0.3770.29047 1.12 1.25 0.84 0.92 SWPA252012S5R1MT 5.1±20% 0.5000.38544 1.23 1.37 0.75 0.82SWPA252012S5R6MT 5.6±20%0.5380.41438 1.11 1.25 0.73 0.80SWPA252012S6R2MT 6.2±20% 0.5420.41738 1.03 1.16 0.73 0.80 SWPA252012S6R8MT 6.8±20% 0.5810.44738 0.98 1.09 0.69 0.75 SWPA252012S7R5MT 7.5±20% 0.6110.47035 0.97 1.09 0.68 0.74SWPA252012S8R2MT 8.2±20% 0.6580.50636 0.98 1.10 0.65 0.71 SWPA252012S9R1MT 9.1±20%0.6900.53134 0.91 1.02 0.62 0.68SWPA252012S100MT 10±20% 0.6900.53134 0.79 0.88 0.62 0.68SWPA252012S120MT 12±20%1.0750.82728 0.78 0.88 0.51 0.56 SWPA252012S150MT 15±20%1.591 1.22425 0.68 0.77 0.42 0.46SWPA3010S Series Part NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat IrmsSWPA3010S1R0NT 1.0±30% 0.0850.065180 1.40 2.10 1.45 1.80 SWPA3010S1R2NT 1.2±30% 0.0850.065137 1.25 1.70 1.45 1.80 SWPA3010S1R5NT 1.5±30% 0.1040.080120 1.27 1.70 1.30 1.60 SWPA3010S2R2NT 2.2±30% 0.1430.110100 1.15 1.50 1.09 1.40 SWPA3010S2R7NT 2.7±30% 0.1690.13090 1.00 1.20 1.02 1.40 SWPA3010S3R3NT 3.3±30% 0.1890.14574 0.97 1.20 0.96 1.20 SWPA3010S3R6MT 3.6±20% 0.2150.16567 0.95 1.20 0.90 1.10 SWPA3010S4R7MT 4.7±20% 0.2930.22559 0.75 1.05 0.77 1.10 SWPA3010S5R6MT 5.6±20% 0.322 0.248 40 0.58 0.65 0.70 1.05 SWPA3010S6R8MT 6.8±20% 0.3970.30542 0.55 0.72 0.66 0.96 SWPA3010S8R2MT 8.2±20% 0.520 0.40 23 0.55 0.70 0.58 0.70 SWPA3010S100MT 10±20% 0.5200.40 39 0.55 0.75 0.58 0.70 SWPA3010S120MT 12±20% 0.6570.50536 0.43 0.65 0.52 0.67 SWPA3010S150MT 15±20% 0.7930.61030 0.42 0.57 0.47 0.57 SWPA3010S220MT 22±20% 1.2090.93028 0.35 0.48 0.38 0.52 SWPA3010S270MT 27±20% 1.404 1.08025 0.30 0.45 0.35 0.50 SWPA3010S330MT 33±20% 2.015 1.55018 0.29 0.42 0.30 0.55 SWPA3010S390MT 39±20% 2.275 1.75018 0.28 0.38 0.28 0.53 SWPA3010S430MT 43±20% 2.340 1.80 18 0.23 0.36 0.27 0.52 SWPA3010S470MT 47±20% 2.535 1.95018 0.22 0.35 0.26 0.52 SWPA3010S510MT 51±20% 2.860 2.20 18 0.21 0.33 0.25 0.48SWPA3010S560MT 56±20% 3.016 2.32016 0.21 0.280.24 0.35SWPA3012S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat Irms SWPA3012SR22NT 0.22±30% 0.022 0.017 321 5.30 6.00 3.00 3.30 SWPA3012SR82NT 0.82±30% 0.039 0.030 180 2.05 2.80 2.47 3.00 SWPA3012S1R0NT 1.0±30% 0.052 0.040 120 1.87 2.80 2.20 2.70 SWPA3012S1R2NT 1.2±30% 0.059 0.045 120 2.22 2.50 2.01 2.20 SWPA3012S1R5NT 1.5±30% 0.0590.045 110 1.62 1.90 2.01 2.20 SWPA3012S1R8NT 1.8±30% 0.0820.063 90 1.30 1.90 1.65 1.80 SWPA3012S2R2NT 2.2±30% 0.0980.075 84 1.20 1.90 1.55 1.70 SWPA3012S2R4NT 2.4±30% 0.0880.068 100 1.15 1.50 1.60 1.70 SWPA3012S2R7NT 2.7±30% 0.1100.085 65 1.14 1.50 1.48 1.50 SWPA3012S3R3MT 3.3±20% 0.1300.10 64 1.05 1.50 1.36 1.40 SWPA3012S3R6MT 3.6±20% 0.1300.10 36 1.05 1.50 1.36 1.40 SWPA3012S3R9MT 3.9±20% 0.189 0.145 61 1.00 1.30 1.24 1.30 SWPA3012S4R7MT 4.7±20% 0.1560.120 61 0.90 1.00 1.24 1.30 SWPA3012S5R6MT 5.6±20% 0.2260.17461 0.80 1.10 1.13 1.24 SWPA3012S6R8MT 6.8±20% 0.2470.190 61 0.75 0.90 0.98 1.10 SWPA3012S100MT 10±20% 0.3450.265 42 0.60 0.88 0.83 0.90 SWPA3012S120MT 12±20% 0.4490.345 32 0.48 0.67 0.73 0.84SWPA3012S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH Ω MHz A A Symbol L DCR S.R.F Isat Irms SWPA3012S220MT 22±20% 0.839 0.645 23 0.42 0.52 0.53 0.59 SWPA3012S270MT 27±20% 1.131 0.870 21 0.35 0.48 0.47 0.51 SWPA3012S330MT 33±20% 1.138 0.875 18 0.36 0.46 0.46 0.50 SWPA3012S360MT 36±20% 1.235 0.950 18 0.34 0.44 0.44 0.48 SWPA3012S390MT 39±20% 1.729 1.330 18 0.30 0.39 0.37 0.41 SWPA3012S470MT 47±20% 1.885 1.450 14 0.27 0.35 0.35 0.40 SWPA3012S560MT 56±20% 1.794 1.380 9 0.26 0.33 0.28 0.40 SWPA3012S680MT 68±20% 2.171 1.670 7 0.24 0.29 0.33 0.37 SWPA3012S820MT 82±20% 3.302 2.540 7 0.17 0.27 0.27 0.31 SWPA3012S101MT 100±20% 3.718 2.860 5 0.21 0.23 0.25 0.29SWPA3015S SeriesPart NumberInductanceDC ResistanceSelf-resonant Frequency Saturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min.Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA3015SR50NT 0.5±30% 0.039 0.030 162 3.90 4.20 2.60 2.80 SWPA3015S1R0NT 1.0±30% 0.039 0.030 150 2.32 2.80 2.35 2.50 SWPA3015S1R2NT 1.2±30% 0.052 0.040 110 2.21 3.10 1.95 2.30 SWPA3015S1R5NT 1.5±30% 0.065 0.050 100 2.30 2.70 1.70 2.20 SWPA3015S1R8NT 1.8±30% 0.065 0.050 92 1.75 2.20 1.70 2.20 SWPA3015S2R2NT 2.2±30% 0.078 0.060 86 1.60 2.00 1.60 2.00 SWPA3015S2R7NT 2.7±30% 0.098 0.075 64 1.52 1.90 1.43 1.90 SWPA3015S3R3MT 3.3±20% 0.104 0.080 68 1.32 1.81 1.36 1.60 SWPA3015S3R6MT 3.6±20% 0.137 0.105 59 1.28 1.60 1.20 1.50 SWPA3015S3R9MT 3.9±20% 0.137 0.105 47 1.20 1.40 1.20 1.50 SWPA3015S4R3MT 4.3±20% 0.150 0.115 53 1.20 1.40 1.14 1.30 SWPA3015S4R7MT 4.7±20% 0.163 0.125 46 1.10 1.40 1.09 1.30 SWPA3015S5R1MT 5.1±20% 0.173 0.133 49 1.00 1.20 1.05 1.20 SWPA3015S6R2MT 6.2±20% 0.254 0.195 46 1.00 1.20 0.86 1.00 SWPA3015S6R8MT 6.8±20% 0.260 0.20 39 0.85 1.10 0.85 1.10 SWPA3015S100MT 10±20% 0.325 0.250 41 0.72 0.92 0.77 0.90 SWPA3015S120MT 12±20% 0.416 0.320 32 0.70 0.90 0.68 0.89 SWPA3015S150MT 15±20% 0.455 0.350 30 0.66 0.88 0.65 0.72 SWPA3015S180MT 18±20% 0.559 0.430 23 0.56 0.72 0.59 0.72 SWPA3015S220MT 22±20% 0.598 0.46023 0.52 0.68 0.57 0.69 SWPA3015S270MT 27±20% 0.949 0.730 22 0.48 0.56 0.45 0.56 SWPA3015S330MT 33±20% 1.066 0.820 20 0.44 0.53 0.43 0.51 SWPA3015S390MT 39±20% 1.294 0.995 14 0.41 0.55 0.39 0.44 SWPA3015S430MT 43±20% 1.378 1.060 16 0.37 0.43 0.37 0.48 SWPA3015S470MT 47±20% 1.625 1.250 14 0.35 0.43 0.35 0.44 SWPA3015S560MT 56±20% 1.664 1.280 13 0.33 0.42 0.34 0.41 SWPA3015S620MT 62±20% 2.093 1.610 13 0.30 0.40 0.30 0.41 SWPA3015S680MT 68±20% 3.510 2.700 110.28 0.37 0.23 0.31 SWPA3015S101MT 100±20% 4.043 3.110 6.3 0.23 0.25 0.21 0.25SWPA4010S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min.Max.Typ. Max. Typ.Units μH ΩMHz AASymbol L DCR S.R.F Isat Irms SWPA4010S1R0NT 1.0±30% 0.067 0.056 116 2.00 2.30 1.90 2.40 SWPA4010S1R5NT 1.5±30% 0.084 0.070 94 1.68 2.00 1.70 2.00 SWPA4010S2R2MT 2.2±20% 0.102 0.085 73 1.20 1.50 1.50 2.00 SWPA4010S3R3MT 3.3±20% 0.120 0.10 58 1.10 1.40 1.40 1.80 SWPA4010S4R7MT 4.7±20% 0.168 0.140 47 0.95 1.10 1.20 1.50 SWPA4010S6R8MT 6.8±20% 0.240 0.20 38 0.80 0.95 1.00 1.20 SWPA4010S100MT 10±20% 0.360 0.30 31 0.62 0.75 0.75 1.00 SWPA4010S150MT 15±20% 0.516 0.43024 0.54 0.610.60 0.85 SWPA4010S220MT 22±20% 0.684 0.570 19 0.45 0.520.50 0.75SWPA4012S SeriesPart NumberInductance DC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min.Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4012SR82NT 0.82±30% 0.065 0.050 150 3.02 3.30 1.65 2.50 SWPA4012S1R0NT 1.0±30% 0.065 0.050 120 2.61 3.20 1.65 2.50 SWPA4012S1R5NT 1.5±30% 0.085 0.065 90 2.10 2.70 1.46 2.20 SWPA4012S1R8NT 1.8±30% 0.104 0.080 88 2.12 2.60 1.32 1.90 SWPA4012S2R2NT 2.2±30% 0.104 0.080 74 1.76 2.30 1.32 1.90 SWPA4012S2R7NT 2.7±30% 0.117 0.090 71 1.90 2.30 1.25 1.70 SWPA4012S3R3NT 3.3±30% 0.143 0.110 60 1.72 2.10 1.12 1.60 SWPA4012S3R6NT 3.6±30% 0.143 0.110 57 1.20 1.70 1.12 1.60 SWPA4012S4R3NT 4.3±30% 0.182 0.140 54 1.58 1.70 1.00 1.50 SWPA4012S4R7NT 4.7±30% 0.163 0.125 50 1.15 1.80 1.05 1.50 SWPA4012S5R1NT 5.1±30% 0.201 0.155 50 1.55 1.60 0.95 1.50 SWPA4012S5R6NT 5.6±30% 0.182 0.140 42 1.00 1.60 1.00 1.20 SWPA4012S6R8MT 6.8±20% 0.257 0.198 40 0.85 1.40 0.84 1.20 SWPA4012S100MT 10±20% 0.345 0.265 33 0.80 1.10 0.77 1.00 SWPA4012S120MT 12±20% 0.377 0.290 32 0.66 1.00 0.70 0.95 SWPA4012S150MT 15±20% 0.442 0.340 25 0.56 0.80 0.64 0.85 SWPA4012S180MT 18±20% 0.611 0.470 23 0.55 0.75 0.55 0.80 SWPA4012S220MT 22±20% 0.763 0.587 20 0.46 0.70 0.49 0.75 SWPA4012S270MT 27±20% 0.936 0.720 18 0.50 0.70 0.45 0.60 SWPA4012S330MT 33±20% 1.053 0.810 17 0.42 0.60 0.42 0.58 SWPA4012S360MT 36±20% 1.170 0.90 14 0.40 0.50 0.40 0.56 SWPA4012S390MT 39±20% 1.430 1.10 16 0.55 0.66 0.37 0.50 SWPA4012S470MT 47±20% 1.430 1.10 12 0.35 0.50 0.37 0.50 SWPA4012S560MT 56±20% 1.625 1.250 11 0.33 0.45 0.33 0.46 SWPA4012S680MT 68±20% 2.535 1.950 11 0.38 0.45 0.27 0.45 SWPA4012S820MT 82±20% 2.782 2.140 11 0.28 0.40 0.26 0.36SWPA4018S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4018SR47NT 0.47±30% 0.0180.014155 4.30 5.20 4.00 4.50 SWPA4018SR68NT 0.68±30% 0.0260.020128 4.90 5.60 3.30 3.80 SWPA4018S1R0NT 1.0±30% 0.0330.02580 4.80 5.20 2.00 3.30 SWPA4018S1R5NT 1.5±30% 0.0390.03065 3.35 4.00 1.80 3.20 SWPA4018S1R8NT 1.8±30% 0.0440.03454 3.00 3.40 2.00 2.80 SWPA4018S2R2MT 2.2±20% 0.0590.04552 2.70 3.20 1.65 2.60 SWPA4018S3R3MT 3.3±20% 0.0910.07044 2.45 2.90 1.23 2.10 SWPA4018S4R7MT 4.7±20% 0.1170.09034 1.70 2.20 1.20 1.80 SWPA4018S6R8MT 6.8±20% 0.1430.11029 1.45 2.00 1.06 1.50 SWPA4018S100MT 10±20% 0.2340.18024 1.30 1.60 0.84 1.20 SWPA4018S150MT 15±20% 0.3250.25019 0.94 1.10 0.65 1.00 SWPA4018S220MT 22±20% 0.4680.36016 0.80 0.88 0.59 0.85 SWPA4018S270MT 27±20% 0.6110.47027 0.47 0.62 0.52 0.90 SWPA4018S330MT 33±20% 0.6890.53012 0.56 0.75 0.49 0.72 SWPA4018S470MT 47±20% 0.8450.65010 0.57 0.70 0.42 0.65 SWPA4018S680MT 68±20% 1.30 1.0 8.3 0.47 0.51 0.32 0.52 SWPA4018S101MT 100±20% 2.275 1.750 6.5 0.40 0.44 0.25 0.41 SWPA4018S151MT 150±20% 3.250 2.50 5.5 0.31 0.34 0.22 0.36 SWPA4018S221MT 220±20% 5.20 4.0 4 0.27 0.30 0.17 0.27SWPA4020S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat IrmsSWPA4020SR24MT 0.24±20% 0.0140.011283 10.5 12.5 4.50 5.20 SWPA4020SR33NT 0.33±30% 0.0160.013223 7.50 8.50 3.30 4.90 SWPA4020SR47NT 0.47±30% 0.0290.022160 7.00 7.50 3.30 3.70 SWPA4020SR68NT 0.68±30% 0.0360.028120 6.40 6.60 2.80 3.30 SWPA4020S1R0NT 1.0±30% 0.0380.02975 4.78 5.20 2.15 3.20 SWPA4020S1R2NT 1.2±30% 0.0380.02972 5.10 5.60 2.15 3.20 SWPA4020S1R5NT 1.5±30% 0.0460.03571 4.45 4.90 1.98 3.00 SWPA4020S2R2NT 2.2±30% 0.0520.04049 3.40 3.70 1.85 2.80 SWPA4020S3R3MT 3.3±20% 0.0910.07044 3.20 3.50 1.40 2.50 SWPA4020S3R6MT 3.6±20% 0.0720.05549 2.80 3.00 1.54 2.50 SWPA4020S4R7MT 4.7±20% 0.0980.07542 2.35 2.50 1.34 2.00 SWPA4020S5R1MT 5.1±20% 0.111 0.08542 2.30 2.50 1.27 1.80 SWPA4020S5R6MT 5.6±20% 0.1170.09030 2.20 2.40 1.22 1.80 SWPA4020S6R2MT 6.2±20% 0.1500.11536 2.15 2.30 1.08 1.60 SWPA4020S6R8MT 6.8±20% 0.1630.12533 2.20 2.40 1.04 1.60 SWPA4020S7R5MT 7.5±20% 0.1500.11530 1.85 2.00 1.08 1.50 SWPA4020S8R2MT 8.2±20% 0.1630.12527 1.75 1.90 1.04 1.40 SWPA4020S100MT 10±20% 0.2150.16526 1.60 1.70 0.90 1.20 SWPA4020S120MT 12±20% 0.2280.17526 1.50 1.60 0.88 1.20 SWPA4020S150MT 15±20% 0.2990.23024 1.35 1.50 0.77 1.10SWPA4020S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4020S330MT 33±20% 0.7150.55011 0.850.930.490.68SWPA4020S390MT 39±20% 0.8450.65011 0.820.900.460.64SWPA4020S430MT 43±20% 0.8580.66010 0.770.850.450.63SWPA4020S470MT 47±20% 0.9230.71010 0.740.810.440.61SWPA4020S510MT 51±20% 0.9750.75010 0.700.770.420.59SWPA4020S560MT 56±20% 1.0400.80 10 0.660.720.410.57SWPA4020S620MT 62±20% 1.1700.90 9.6 0.650.710.390.52SWPA4020S680MT 68±20% 1.380 1.0607.7 0.610.670.360.50SWPA4020S750MT 75±20% 1.510 1.1607.7 0.700.770.350.49SWPA4020S820MT 82±20% 1.520 1.1707.2 0.500.550.340.47SWPA4020S101MT 100±20% 2.020 1.550 6.3 0.480.530.310.43 SWPA4026S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4026S1R0NT 1.0±30% 0.0310.024151 3.303.803.003.30SWPA4026S1R2NT 1.2±30% 0.0390.030120 3.103.402.303.30SWPA4026S1R5NT 1.5±30% 0.0390.030100 2.402.902.303.10SWPA4026S2R2MT 2.2±20% 0.0520.04096 2.102.402.003.80SWPA4026S3R3MT 3.3±20% 0.0650.05058 1.802.001.702.50SWPA4026S4R7MT 4.7±20% 0.0720.05546 1.451.701.602.30SWPA4026S6R8MT 6.8±20% 0.0850.06533 1.301.501.502.00SWPA4026S100MT 10±20% 0.1100.08526 1.001.201.301.90SWPA4026S150MT 15±20% 0.1430.11019 0.901.001.101.50SWPA4026S220MT 22±20% 0.2140.16513 0.600.800.901.40SWPA4026S330MT 33±20% 0.3510.2709 0.550.650.701.00SWPA4026S470MT 47±20% 0.3900.30 6 0.400.550.650.90 SWPA4030S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4030SR68NT 0.68±30% 0.0130.010130 6.80 8.00 4.56 5.10 SWPA4030SR91NT 0.91±30% 0.0170.013100 6.25 6.80 4.15 4.70 SWPA4030S1R0NT 1.0±30% 0.0180.01470 5.26 5.70 4.15 4.70 SWPA4030S1R2NT 1.2±30% 0.0200.01580 5.80 6.30 3.82 4.20 SWPA4030S1R5NT 1.5±30% 0.0260.02062 4.84 5.30 3.34 3.60 SWPA4030S1R8NT 1.8±30% 0.0330.02560 5.40 5.80 3.20 3.30 SWPA4030S2R2NT 2.2±30% 0.0390.03052 4.90 5.80 2.95 3.20SWPA4030S SeriesPart NumberInductanceDC ResistanceSelf-resonant Frequency Saturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz AA Symbol L DCR S.R.F Isat Irms SWPA4030S4R3MT 4.3±20% 0.072 0.05537 2.95 3.20 2.10 2.30 SWPA4030S4R7MT 4.7±20% 0.078 0.06031 2.90 3.20 2.00 2.30 SWPA4030S5R6MT 5.6±20% 0.085 0.06530 2.60 2.80 1.95 2.10 SWPA4030S6R8MT 6.8±20% 0.1170.09024 2.75 3.00 1.60 1.70 SWPA4030S7R5MT 7.5±20% 0.110 0.08526 2.20 2.40 1.65 1.80 SWPA4030S8R2MT 8.2±20% 0.117 0.09026 2.10 2.30 1.60 1.70 SWPA4030S100MT 10±20% 0.1300.10 21 1.95 2.40 1.50 1.60 SWPA4030S120MT 12±20% 0.1750.13518 1.70 1.80 1.30 1.40 SWPA4030S150MT 15±20% 0.2470.19016 1.65 1.80 1.11 1.20 SWPA4030S180MT 18±20% 0.2600.20 10 1.40 1.50 1.10 1.20 SWPA4030S220MT 22±20% 0.2920.22510 1.30 1.40 1.00 1.20 SWPA4030S270MT 27±20% 0.3380.26010 1.15 1.35 0.90 1.05 SWPA4030S330MT 33±20% 0.4290.33010 1.10 1.20 0.84 0.92 SWPA4030S360MT 36±20% 0.4360.3359.8 1.05 1.10 0.83 0.91 SWPA4030S390MT 39±20% 0.5660.43510 1.03 1.10 0.73 0.80 SWPA4030S470MT 47±20% 0.5790.4458.4 0.95 1.00 0.72 0.80 SWPA4030S510MT 51±20% 0.6110.4708.4 0.90 1.13 0.70 0.80 SWPA4030S560MT 56±20% 0.7220.5558.4 0.85 0.94 0.65 0.71 SWPA4030S620MT 62±20% 0.7610.5857 0.80 0.99 0.63 0.70 SWPA4030S680MT 68±20% 1.1280.8687 0.72 0.80 0.52 0.57 SWPA4030S750MT 75±20% 1.326 1.020 6.3 0.70 0.88 0.48 0.53 SWPA4030S820MT 82±20% 1.378 1.060 5.6 0.66 0.72 0.47 0.52 SWPA4030S910MT 91±20% 1.430 1.10 5.6 0.65 0.71 0.46 0.50 SWPA4030S101MT 100±20% 1.495 1.150 5.6 0.60 0.73 0.45 0.49 SWPA4030S121MT 120±20% 1.755 1.350 5.4 0.55 0.60 0.42 0.46 SWPA4030S151MT 150±20% 2.340 1.80 4 0.50 0.55 0.30 0.35 SWPA4030S221MT 220±20% 3.250 2.50 4.2 0.40 0.50 0.35 0.40 SWPA4030S331MT 330±20% 5.20 4.0 6.8 0.30 0.40 0.25 0.26 SWPA4030S471KT 470±10% 9.3607.20 2 0.30 0.35 0.20 0.23 SWPA4030S501MT 500±20% 9.027 6.9442 0.28 0.30 0.15 0.20 SWPA4030S681MT 680±20% 9.8547.580 1.2 0.190.200.14 0.18SWPA5012S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat Irms SWPA5012SR22NT 0.22±30% 0.0340.028315 8.10 9.30 3.00 3.30 SWPA5012S1R0NT 1.0±30% 0.0680.057103 4.40 4.70 2.00 2.40 SWPA5012S1R5NT 1.5±30% 0.0860.07268 3.70 3.80 1.90 2.20 SWPA5012S2R2NT 2.2±30% 0.1080.09050 3.10 3.20 1.70 2.00 SWPA5012S3R3NT 3.3±30% 0.1510.12634 2.40 2.60 1.40 1.70SWPA5012S4R7NT 4.7±30% 0.1970.16431 2.20 2.30 1.30 1.50SWPA5012S6R8MT 6.8±20% 0.2940.24522 1.70 1.90 1.00 1.20SWPA5012S SeriesPart NumberInductanceDC ResistanceSelf-resonantFrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min.Max.Typ. Max. Typ.Units μH ΩMHz AA Symbol L DCR S.R.FIsat IrmsSWPA5012S220MT 22±20% 0.858 0.780 16 0.88 0.980.60 0.68SWPA5020S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat Irms SWPA5020SR22NT 0.22±30% 0.0110.009280 9.00 12.00 5.30 6.00 SWPA5020SR24NT 0.24±30% 0.0110.009248 8.00 10.00 5.30 6.00 SWPA5020SR47NT 0.47±30% 0.0170.013160 6.15 6.70 4.60 5.00 SWPA5020SR56NT 0.56±30% 0.0220.017137 8.50 9.60 3.80 4.20 SWPA5020SR68MT 0.68±30% 0.0220.017120 5.50 6.00 4.00 4.40 SWPA5020SR75NT 0.75±30% 0.0220.017117 5.50 6.00 4.00 4.40 SWPA5020S1R0NT 1.0±30% 0.0260.020114 4.10 5.00 3.80 4.10 SWPA5020S1R2NT 1.2±30% 0.0290.02283 4.50 4.90 3.55 3.90 SWPA5020S1R5NT 1.5±30% 0.0340.02668 4.10 4.50 3.20 3.50 SWPA5020S2R2NT 2.2±30% 0.0420.03257 3.20 4.00 2.90 3.10 SWPA5020S2R7NT 2.7±30% 0.0490.03852 2.90 3.50 2.70 2.90 SWPA5020S3R0NT 3.0±30% 0.0490.03849 2.55 2.80 2.70 2.90 SWPA5020S3R3NT 3.3±30% 0.0560.04346 2.55 3.00 2.50 2.70 SWPA5020S3R6NT 3.6±30% 0.0560.04343 2.80 3.00 2.50 2.70 SWPA5020S3R9NT 3.9±30% 0.0560.04340 2.30 2.80 2.50 2.70 SWPA5020S4R3MT 4.3±20% 0.0740.05737 2.50 3.00 2.20 2.40 SWPA5020S4R7MT 4.7±20% 0.0740.05737 2.50 2.70 2.20 2.40 SWPA5020S5R1MT 5.1±20% 0.0830.06432 2.25 2.60 2.05 2.20 SWPA5020S5R6MT 5.6±20% 0.0830.06432 2.30 2.50 2.05 2.20 SWPA5020S6R8MT 6.8±20% 0.1080.08330 2.05 2.20 1.80 1.90 SWPA5020S7R5MT 7.5±20% 0.1170.09026 1.85 2.00 1.75 1.90 SWPA5020S8R2MT 8.2±20% 0.1270.09826 1.85 2.00 1.65 1.80 SWPA5020S9R1MT 9.1±20% 0.1430.11024 1.70 1.80 1.55 1.70 SWPA5020S100MT 10±20% 0.1430.11024 1.70 1.80 1.55 1.70 SWPA5020S120MT 12±20% 0.1820.14022 1.50 1.60 1.40 1.50 SWPA5020S150MT 15±20% 0.2150.16520 1.35 1.40 1.25 1.30 SWPA5020S180MT 18±20% 0.2600.20 16 1.25 1.30 1.15 1.20 SWPA5020S220MT 22±20% 0.2940.22614 1.15 1.20 1.10 1.20 SWPA5020S330MT 33±20% 0.5070.39010 0.92 1.00 0.90 0.99 SWPA5020S470MT 47±20% 0.6800.5237 0.77 0.84 0.77 0.84 SWPA5020S560MT 56±20% 0.8190.630 6 0.77 0.84 0.70 0.77 SWPA5020S680MT 68±20% 0.9620.740 6 0.65 0.70 0.64 0.70 SWPA5020S820MT 82±20% 1.1580.965 6 0.65 0.75 0.50 0.60 SWPA5020S101MT 100±20% 1.430 1.10 6 0.53 0.58 0.53 0.58 SWPA5020S121MT 120±20% 1.755 1.350 6 0.42 0.53 0.40 0.50SWPA5040S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat Irms SWPA5040SR22MT 0.22 ±20% 0.0080.006289 18.0020.00 6.50 7.50 SWPA5040SR24NT 0.24 ±30% 0.0080.006251 15.7018.00 6.40 7.40 SWPA5040SR47MT 0.47 ±20% 0.0090.007171 10.0011.50 6.60 7.60 SWPA5040S1R0NT 1.0±30% 0.0160.012117 7.35 8.00 4.90 5.00 SWPA5040S1R2NT 1.2±30% 0.0210.016110 6.50 7.00 4.15 4.25 SWPA5040S1R5NT 1.5±30% 0.0200.01586 6.30 6.80 4.30 4.85 SWPA5040S1R8MT 1.8±20% 0.0210.01655 5.50 6.05 4.15 4.30 SWPA5040S2R2NT 2.2±30% 0.0250.01950 4.90 5.50 3.80 4.20 SWPA5040S2R7NT 2.7±30% 0.0290.02237 4.30 4.80 3.60 4.00 SWPA5040S3R0NT 3.0±30% 0.0290.02237 4.15 4.60 3.60 4.00 SWPA5040S3R3NT 3.3±30% 0.0310.02432 3.95 4.45 3.40 3.90 SWPA5040S3R6MT 3.6±20% 0.0340.02630 3.80 4.40 3.30 3.70 SWPA5040S3R9NT 3.9±30% 0.0350.02729 3.55 4.00 3.20 3.70 SWPA5040S4R7NT 4.7±30% 0.0390.03028 3.50 3.80 3.00 3.30 SWPA5040S5R6MT 5.6±20% 0.0460.03527 3.00 3.70 2.80 3.10 SWPA5040S6R8MT 6.8±20% 0.0560.04321 2.90 3.40 2.50 2.80 SWPA5040S8R2MT 8.2±20% 0.0620.04820 2.70 2.90 2.30 2.60 SWPA5040S100MT 10±20% 0.0830.06418 2.35 2.70 2.10 2.35 SWPA5040S120MT 12±20% 0.1000.07714 2.2 2.5 2.0 2.1 SWPA5040S150MT 15±20% 0.1120.08613 2.00 2.20 2.00 2.05 SWPA5040S180MT 18±20% 0.1550.11912 1.70 2.00 1.45 1.65 SWPA5040S220MT 22±20% 0.1680.12911 1.60 1.80 1.50 1.60 SWPA5040S270MT 27±20% 0.2440.1889.8 1.52 1.75 1.10 1.25 SWPA5040S330MT 33±20% 0.2440.1889 1.30 1.45 1.20 1.35 SWPA5040S470MT 47±20% 0.3540.2727 1.10 1.20 1.00 1.15 SWPA5040S510MT 51±20% 0.4940.380 6 1.00 1.20 1.00 1.10 SWPA5040S560MT 56±20% 0.4940.380 6 1.05 1.20 0.80 0.90 SWPA5040S680MT 68±20% 0.5200.40 6 0.90 1.00 0.80 0.90 SWPA5040S750MT 75±20% 0.5850.450 6 0.85 0.95 0.72 0.80 SWPA5040S101MT 100±20% 0.7280.560 5 0.75 0.85 0.70 0.78 SWPA5040S151MT 150±20% 0.9750.750 3.7 0.65 0.67 0.60 0.70 SWPA5040S221MT 220±20% 1.820 1.40 3.0 0.48 0.55 0.40 0.50 SWPA5040S301MT 300±20% 2.60 2.0 2.7 0.50 0.58 0.35 0.40 SWPA5040S331MT 330±20% 2.730 2.10 2.7 0.42 0.47 0.40 0.50 SWPA5040S471MT 470±20% 3.90 3.0 2.7 0.37 0.43 0.35 0.40 SWPA5040S561MT 560±20% 4.920 3.780 1.3 0.31 0.36 0.31 0.35 SWPA5040S681MT 680±20% 5.070 3.90 1.3 0.30 0.35 0.25 0.30 SWPA5040S102MT 1000±20% 7.80 6.0 1.3 0.21 0.25 0.20 0.23 SWPA5040S332MT 3300±20% 25.2021.00.9 0.1400.150 0.100 0.120SWPA5040S392MT 3900±20% 30.5523.500.8 0.1250.150 0.100 0.115SWPA5040S472MT 4700±20% 45.5035.00.6 0.1100.130 0.080 0.100SWPA5040S502MT 5000±20% 43.1635.970.49 0.1100.130 0.085 0.098SWPA5040S562MT 5600±20% 50.7039.00.49 0.1050.120 0.080 0.092SWPA5040S682MT 6800±20% 55.9043.00.38 0.0900.110 0.0750.086SWPA5040S822MT 8200±20% 55.9043.00.38 0.0700.085 0.075 0.086SWPA5040S103MT 10000±20% 58.5045.00.32 0.0650.075 0.075 0.086。

DCM4532[1812 inch]DCM3225[1210 inch]DCM2520[1008 inch]DCM2012[0805 inch]*DCM series•All specifications are subject to change without notice.•Conformity to RoHS Directive: This means that, in conformity with EU Directive 2002/95/EC, lead, cadmium, mercury, hexavalent chromium, and specific bromine-based flame retardants, PBB and PBDE, have not been used, except for exempted applications.Common Mode FiltersFor high-speed differential signal line/general signal line Type:* Dimensions Code [EIA](6) internal codeDCM4532DCM3225DCM2520DCM2012DCM Series DCM2012, 2520, 3225, 4532DCM 2012 -900-2P -T Common Mode FiltersFor High-speed Differential Signal Line / General Signal LineFEATURES•Although greatly miniaturized, this wire-wound chip-type filter maintains the characteristics needed for a common mode filter. Common mode impedance is 1000Ω [at 100MHz], so this filter is greatly effective in supporting noise.•Almost no affect upon even high speed signals since differential mode impedance is kept low.•This series includes both 2-line and 3-line types. They are used for various types of circuits and noise.APPLICATIONS•Used for radiation noise suppression for any electronic devices. •Used to counter common mode noise affecting signals within high-speed lines.•USB line for personal computers and peripheral equipment. •IEEE1394 line for personal computers, DVC, STB, etc.•LVDS, panel link line for liquid crystal display panels.TEMPERATURE RANGESPACKAGING STYLE AND QUANTITIESPRODUCT IDENTIFICATION (1) Series name(2) Dimensions L ×W 2012: 2.0×1.2mm(3) Impedance[at 100MHz]900: 90Ω(4) Number of line2P: 2-line 3P: 3-line(5) Packaging styleT: ø180mm reel taping TL: ø330mm reel taping RECOMMENDED SOLDERING CONDITIONS RECOMMENDED TEMPERATURE PROFILE FOR LEAD-FREE SOLDERREFLOW PROFILE FOR SOLDER HEAT RESISTANCEConformity to RoHS Directive Operating–25 to +85°C Storage(After mount)–25 to +85°CPackaging styleT ype Reel QuantityT apingø180mm 2000 pieces/reel ø330mm 10000 pieces/reel ø180mm 2000 pieces/reel ø330mm 10000 pieces/reel ø180mm 1000 pieces/reel ø330mm 5000 pieces/reel ø180mm 500 pieces/reel ø330mm2000 pieces/reel(1)(2)(3)(4)(5)(6)DCM2520-3P DCM4532-102-3PDCM2520-2P DCM3225-2PDCM2012-2PSHAPES AND DIMENSIONS/CIRCUIT DIAGRAMS/RECOMMENDED PC BOARD PATTERNS 2-LINE TYPE 3-LINE TYPEDCM4532-102-3P10000.6200.2DCM2520-801-3P 800 1.6200.15DCM3225-102-2P 10000.5200.2DCM3225-271-2P 2700.3200.3DCM3225-161-2P 1600.2200.35DCM3225-800-2P 800.15200.4DCM2520-102-2P 10000.9200.2DCM2520-601-2P 6000.45200.3DCM2520-451-2P 4500.4200.35DCM2520-301-2P 3000.35200.4DCM2012-361-2P 3600.5500.22DCM2012-201-2P 2000.25500.35DCM2012-121-2P 1200.22500.37DCM2012-900-2P 900.19500.4ELECTRICAL CHARACTERISTICSPart No.Impedance(Ω)typ.[100MHz]DC resistance(Ω)max.[per 1 line]Rated voltage Edc(V)max.Rated current Idc(A)max.2-LINE3-LINEDCM3225-271-2P DCM3225-102-2PDCM3225-800-2P DCM3225-161-2PDCM2520-601-2P DCM2520-102-2PDCM2520-301-2P DCM2520-451-2PDCM2012-201-2P DCM2012-361-2PDCM2012-900-2P DCM2012-121-2PMEASURING CIRCUITS 2-LINEDCM2520-801-3P DCM4532-102-3PIMPEDANCE vs. FREQUENCY CHARACTERISTICS 3-LINEMEASURING CIRCUITS 3-LINE。

注意：安装、运行、维护或检查之前要认真阅读本说明书。

设备的设计、安装、调试和运行，必须由经过培训的专业人员来进行；在工作过程中，必须遵循安装检修中所有的规定，否则可能造成严重的人身伤害或重大财产损失。

1. 注意事项（1）操作前确保电源完全切断。

（2）设备禁止安装在易燃物上，否则有发生火灾的危险。

（3）主回路接线后，应对裸露的接线端子进行绝缘处理，否则会有触电的危险。

（4）通电情况下，不要用潮湿的手操作设备，否则有触电危险。

（5）设备在通电过程中，请勿打开面盖及进行配线作业，必须在关闭电源10分钟后，方可实施配线或检查。

（6）必须具有专业资格的人员才能进行配线作业，严禁将任何导电物遗留在设备内，否则有触电或造成设备损坏的危险。

（7）存贮时间超过2年以上的设备，上电时应先用调压器逐渐升压，否则有触电和爆炸的危险。

（8）严禁将接线端子中R、S、T以外的端子接上交流380V电压，否则有损坏财物的危险。

（9）如果设备有损伤或部件不全时，请不要安装运转，否则有发生火灾或导致人员受伤的危险。

（10）安装时，应该在能够承受设备重量的地方进行安装，否则掉落时有致人受伤或损坏财物的危险。

2．安全须知和维护（1）安全须知因设备工作在380V的三相交变电压，机箱内外线路电压相当高，在设备上电运行时，身体任何部位不可贴近设备的输入输出端子处。

即使感应加热设备处于不工作状态，输入及输出接线端子仍然可能带有威胁电压。

如需查看设备内部状况或检修，必须断开电源，为安全起见应断电几分钟后确保设备无电流时方可开箱检修。

（2）维护为了确保感应加热电源正常运行，延长设备运行寿命，需要对设备进行定期维护，维护的内容如下表所示：检查项目内容温度/湿度确定环境温度在-20℃～+40℃，相对湿度在20%～90%确认设备内无油雾和粉尘、无凝露油雾和粉尘存储环境无腐蚀性气体、液体感应加热设备检查设备有无异常发热、有无异常振动风扇确定风扇运作正常、无杂物卡住等情况输入电源确定输入电源的电压和频率在允许的范围内线圈检查线圈是否正常，无发黄则表明无油雾和粉尘、无凝露表2-1 维护项目鉴于设备工作过程易摄入粉尘，特别在风扇模块，尽量避免因粉尘积压而影响散热导致机箱内部温度过高造成不良效果，为延长设备寿命，建议定期为风机及散热器除尘，不超过两个月一次，定期为机箱内部器件除尘，不超过一年一次。

产品名称：CD贴片功率电感产品特点：产品图片产品图片图型及尺寸参考类 型A B C D ref CD32 3.0±0.3 3.0±0.3 2.1±0.31CD43 4.5±0.3 4.0±0.3 3.2±0.31CD52 5.8±0.3 5.2±0.3 2.1±0.3 1.6CD53 5.8±0.3 5.2±0.3 3.2±0.3 1.6CD54 5.8±0.3 5.2±0.3 4.5±0.3 1.3CD737.8±0.37.0±0.3 3.5±0.3 2.1CD757.8±0.37.0±0.3 5.0±0.3 2.1CD10410.0±0.39.0±0.3 4.0±0.3 2.9CD10510.0±0.39.0±0.35.4±0.32.9LTESTING DC RATED DC uH FREQ.RESISTANCE CURRENT (KHz).(Ω) MAX. A MAX CD32-100K 101000.230.76CD32-120K121000.270.685CD32贴片功率电感参数CD 75 － 221 K (1) (2) (3) (4)编号CD贴片功率电感图型及尺寸( SHAPE AND SIZE) ( 单位 mm )CD贴片功率电感编号表示(1). 编号(Type) : CD32/43/52/53/54/73/75/104/105 ( CD )(2). 尺寸（Size) : 成品外型尺寸（According to size) ( 75 )(3). 电感值(Inductance) : "221"表示220uH（Example: "221"for 220uH) ( 221 )(4). 电感公差（Tolerance) :"M:±20%, "K":±10% , "J":±5% ( K )/index.htm?spm=2013.1.w5002-5830017747.2.EYY36cCD贴片功率电感锰锌大功率电感 1、表面贴装小型功率电感。

1、订货代码 HOW TO ORDER举例 For exampleAL 0307 — 220 K P 52 EA B C D E F GD:感量偏差ToleranceJ ±5.0%K ±10%M ±20%B:尺寸Dimensions（mm）类型Type外径D max体长L max0204 2.3 4.20307 2.8 7.00410 4.0 10.50510 5.0 10.5 A:产品类别Product typeAL轴向色码电感器Axial color code inductorC:标称电感量Nominal inductance (μH)前两位数字为有效数字，后一位数字表示零的个数。

The first two digits are significant, and thethird digit is number of zero.*例如 For example：101=100μH；5R6=5.6μHR22=0.22μHE:包装方式Packaging styleP盒带包装Ammo编带Tape&reel T 卷带包装ReelF直脚轴向AxialL直脚成型Straight lead formedV弯脚成型Bent lead formed散包装BulkVK弯脚K型Bent lead K formedF：引脚形式Lead configuration26编带内距：26mmTape width:编带Tape&reel 52编带内距：52mmTape width:05引脚脚距：5.08mmFormed lead pitch:07引脚脚距：7.5mmFormed lead pitch:10引脚脚距：10.0mmFormed lead pitch:12引脚脚距：12.5mmFormed lead pitch:15引脚脚距：15.0mmFormed lead pitch:17引脚脚距：17.5mmFormed lead pitch:引脚成型Formedlead20引脚脚距：20.0mmFormed lead pitch: G:备注RemarkE无铅Lead Free空格Blank含铅Lead Contained^_^2、外形尺寸 EXTERNAL DIMENSIONS尺 寸Body size （mm ）类型 TypeφD ≤ L ≤ t Φd H ≥AL0204 2.3 4.2t =5.08±0.6t =7.50±0.60.50 ±0.05AL0307 2.8 7.0t =10.0±0.6 t =12.5±0.60.50 ±0.05AL0410 4.0 10.5t =12.5±0.6 t =15.0±0.6t =17.5±0.6 t =20.0±0.60.60 ±0.05AL0510 5.0 10.5 t =15.0±0.6t =17.5±0.6t =20.0±0.60.65 ±0.0520轴向（Axial ）直脚成型（L type ）弯脚成型（V type ） 弯脚K 型（VK type ）3、产品结构 STRUCTURE序号 NO. ① 磁芯 Core ②漆包线 Wire ③引脚 Lead ④涂覆层 Coating ⑤色码Color code材料名称 Material name铁氧体 Ferrite漆包铜线Enamelled wire镀锡铜线 Tinned copperwire环氧树脂 Epoxy resin环氧色漆 Epoxy paint for Color coding^_^４、色码标记代号 MARKING标称电感量Nominal inductance（μH）感量偏差Tolerance第一色环1st color zone第二色环2nd color zone第三色环3rd color zone第四色环4th color zone第一数字1st digit 第二数字2nd digit第三数字3rd digit黑Black 0 0× 100（1）M：±20%棕Brown 1 1× 101（10）红Red 2 2× 102（100）橙Orange 3 3× 103（1000）黄Yellow 4 4× 104（10000）绿Green 5 5× 105（100000）蓝Blue6 6 紫Purple7 7 灰Gray8 8 白White9 9金Gold / /× 10-1（0.1）J：±5%银Silver / /× 10-2（0.01）K：±10%*例如e.g. ：标称电感量及偏差为22uH,±5%的电感器其色码为：红+红+黑+金；If nominal inductance & tolerance is22uH,±5%, respectively red+red+black+gold should be marked;标称电感量及偏差为1.0uH,±10%的电感器其色码为：棕+黑+金+银；If nominal inductance & tolerance is 1.0uH,±10%, respectively brown+black+gold+silver should be marked;标称电感量及偏差为0.22uH,±20%的电感器其色码为：红+红+银+黑。

SM型功率电感器特性：●有出色的高抗饱和性能●体积小，厚度薄用途：●可用于DC-DC变压器和充电器中作储能电感和滤波电感。

外观尺寸：1.SM型电感器外形尺寸规格编码：SM 3521 – 1R0 M (f)○1○2○3○4○5①产品类型代号：②外形尺寸：直径×厚度如：3521：3.5×2.1③标称值：电感器电感量（L）用三位数字、字母表示：对L≥10μH，用三位数字表示，ABC＝AB×10C，单位为微亨，如：100：10μH、121：120μH；对1.0nH≤L＜10μH，用二位数字和表示小数点位置的字母R表示，单位为微亨：如2N7：2.7nH、R10：0.1μH。

○4公差值：用字母“N”表示电感器公差：J＝±5%，K＝±10%，M＝±20%，N＝±30%○5表示无铅产品规格特性：SM3511系列□:表示电感量偏差代号为K、M或者N。

K：±10%；M：±20%；N：±30% SM3516系列□:表示电感量偏差代号为K、M或者N。

K：±10%；M：±20%；N：±30%SM3521系列□:表示电感量偏差代号为K、M或者N。

K：±10%；M：±20%；N：±30%□:表示电感量偏差代号为K、M或者N。

K：±10%；M：±20%；N：±30%□:表示电感量偏差代号为K、M或者N。

K：±10%；M：±20%；N：±30% SM5845系列□:表示电感量偏差代号为K、M或者N。

K：±10%；M：±20%；N：±30% SM7835系列□:表示电感量偏差代号为K、M或者N。

K：±10%；M：±20%；N：±30% SM7850系列□:表示电感量偏差代号为K、M或者N。

Wire Wound SMD Power Inductors – SWPA SeriesOperating temperature range: -40℃~+125℃ (Including self-heating)FEATURES● Magnetic-resin shielded construction reduces buzz noise to ultra-low levels● Metallization on ferrite core results in excellent shock resistance and damage-free durability ● Closed magnetic circuit design reduces leakage flux and Electro Magnetic Interference (EMI) ● 30% higher current rating than conventional inductors of equal size ● Takes up less PCB real estate and save more powerAPPLICATIONS● Smart phone, smart TV, set top box, notebook ● Car navigation systems, telecomm base stations ● VR, AR ● LED lightingPRODUCT IDENTIFICATIONSWPA3012 S 1R0 N T□□□① ② ③ ④ ⑤ ⑥ ⑦②External Dimensions (L×W×H) [mm] 252010 2.5×2.0×1.0 252012 2.5×2.0×1.2 3010 3.0×3.0×1.03012 3.0×3.0×1.2 3015 3.0×3.0×1.5 4010 4.0×4.0×1.0 4012 4.0×4.0×1.2 4018 4.0×4.0×1.8 4020 4.0×4.0×2.0 4026 4.0×4.0×2.6 4030 4.0×4.0×3.0 5012 5.0×5.0×1.2 5020 5.0×5.0×2.0 5040 5.0×5.0×4.0 6020 6.0×6.0×2.0 6028 6.0×6.0×2.8 6040 6.0×6.0×4.0 6045 6.0×6.0×4.5 8040 8.0×8.0×4.0 8050 8.0×8.0×5.0 8060 8.0×8.0×6.08065 8.0×8.0×6.5 ① Type SWPAWire Wound SMD Power Inductor③ Feature TypeS Standard ④ Nominal InductanceExample Nominal Value1R0 1.0μH 100 10μH⑤ Inductance ToleranceK ±10%M ±20% N ±30% ⑥ PackingTTape Carrier Package⑦ Design Code □□□Standard product is blankFig.1 Fig.2Unit: mmSeriesShapeABCD E Fa Typ.b Typ.c Typ.SWPA252010S Fig.1 2.5±0.1 2.0±0.1 1.0 Max. 2.0±0.20.80±0.20.80±0.2 0.80 0.85 2.0 SWPA252012S Fig.1 2.5±0.1 2.0±0.1 1.2 Max. 2.0±0.20.80±0.20.80±0.2 0.80 0.85 2.0 SWPA3010S Fig.2 3.0±0.2 3.0±0.2 1.0 Max. 2.5±0.20.75±0.2 1.5±0.2 1.5 0.8 2.7 SWPA3012S Fig.2 3.0±0.2 3.0±0.2 1.2 Max. 2.5±0.20.75±0.2 1.5±0.2 1.5 0.8 2.7 SWPA3015S Fig.2 3.0±0.2 3.0±0.2 1.5 Max. 2.5±0.20.75±0.2 1.5±0.2 1.5 0.8 2.7 SWPA4010S Fig.2 4.0±0.2 4.0±0.2 1.0 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4012S Fig.2 4.0±0.2 4.0±0.2 1.2 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4018S Fig.2 4.0±0.2 4.0±0.2 1.8 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4020S Fig.2 4.0±0.2 4.0±0.2 2.0 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4026S Fig.2 4.0±0.2 4.0±0.2 2.6 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4030S Fig.2 4.0±0.2 4.0±0.2 3.0 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA5012S Fig.3 5.0±0.2 5.0±0.2 1.2 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA5020S Fig.3 5.0±0.2 5.0±0.2 2.0 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA5040S Fig.3 5.0±0.2 5.0±0.2 4.0 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA5045S Fig.3 5.0±0.2 5.0±0.2 4.5 Max. 4.0±0.2 1.30±0.2 2.5±0.2 2.3 1.4 4.2 SWPA6020S Fig.2 6.0±0.3 6.0±0.3 2.0 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA6028S Fig.2 6.0±0.3 6.0±0.3 2.8 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA6040S Fig.2 6.0±0.3 6.0±0.3 4.0 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA6045S Fig.2 6.0±0.3 6.0±0.3 4.5 Max.4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.75.7 SWPA8040S Fig.2 8.0±0.3 8.0±0.3 4.2 Max.6.3±0.3 2.00±0.3 4.0±0.3 3.8 2.27.5SWPA8050S Fig.3 8.0±0.3 8.0±0.3 5.0 Max. 6.3±0.3 2.00±0.3 4.0±0.3 3.8 2.2 7.5 SWPA8060S Fig.3 8.0±0.3 8.0±0.3 6.0 Max 6.3±0.3 2.00±0.3 4.0±0.3 3.8 2.2 7.5 SWPA8065S Fig.3 8.0±0.3 8.0±0.3 6.5 Max.6.3±0.32.00±0.34.0±0.3 3.8 2.2 7.5SHAPE AND DIMENSIONS SWPA252010S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max. Typ.Min. Max. Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCRS.R.F Isat Irms SWPA252010SR47NT 0.47±30% 0.056 0.047206 2.50 3.35 2.35 2.56 SWPA252010SR56NT 0.56±30% 0.072 0.060160 2.90 3.20 2.00 2.18 SWPA252010SR68NT 0.68±30% 0.074 0.062129 2.20 2.75 2.00 2.18 SWPA252010S1R0NT 1.0±30% 0.1080.090100 1.85 2.20 1.65 1.80 SWPA252010S1R5NT 1.5±30% 0.182 0.15281 1.80 2.10 1.30 1.42 SWPA252010S2R2NT 2.2±30% 0.209 0.17461 1.20 1.60 1.20 1.31 SWPA252010S3R3MT 3.3±20% 0.328 0.27347 1.05 1.30 0.90 0.98 SWPA252010S4R7MT 4.7±20% 0.563 0.46942 0.95 1.15 0.70 0.76 SWPA252010S5R6MT 5.6±20% 0.563 0.46935 0.80 0.95 0.73 0.80 SWPA252010S6R8MT 6.8±20% 0.896 0.74731 0.78 0.92 0.59 0.64 SWPA252010S100MT 10±20% 1.092 0.91027 0.65 0.78 0.50 0.55SWPA252012S SeriesPart NumberInductance DC Resistance Self-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH Ω MHz A A Symbol L DCR S.R.F Isat IrmsSWPA252012SR47NT 0.47±30% 0.0610.047160 3.82 4.27 2.15 2.34 SWPA252012SR68NT 0.68±30% 0.0740.057140 3.28 3.68 1.95 2.13 SWPA252012S1R0NT 1.0±30% 0.0900.069110 2.59 2.90 1.93 2.10 SWPA252012S1R2NT 1.2±30% 0.1290.099100 2.38 2.67 1.46 1.59 SWPA252012S1R5MT 1.5±20% 0.1470.11397 2.24 2.51 1.40 1.53 SWPA252012S1R5NTY01 1.5±30% 0.1300.10 63 1.80 2.00 1.45 1.58 SWPA252012S2R2MT 2.2±20% 0.2160.16669 1.85 2.07 1.15 1.25 SWPA252012S2R2NTY02 2.2±30% 0.1530.11853 1.55 1.75 1.30 1.42 SWPA252012S2R7MT 2.7±20% 0.2390.18463 1.72 1.92 1.09 1.19 SWPA252012S3R3MT 3.3±20% 0.2640.20362 1.61 1.80 1.04 1.13 SWPA252012S3R6MT 3.6±20% 0.3480.26853 1.46 1.64 0.90 0.98 SWPA252012S4R3MT 4.3±20% 0.3770.29051 1.37 1.53 0.87 0.95 SWPA252012S4R7MT 4.7±20% 0.3770.29047 1.12 1.25 0.84 0.92 SWPA252012S5R1MT 5.1±20% 0.5000.38544 1.23 1.37 0.75 0.82SWPA252012S5R6MT 5.6±20%0.5380.41438 1.11 1.25 0.73 0.80SWPA252012S6R2MT 6.2±20% 0.5420.41738 1.03 1.16 0.73 0.80 SWPA252012S6R8MT 6.8±20% 0.5810.44738 0.98 1.09 0.69 0.75 SWPA252012S7R5MT 7.5±20% 0.6110.47035 0.97 1.09 0.68 0.74SWPA252012S8R2MT 8.2±20% 0.6580.50636 0.98 1.10 0.65 0.71 SWPA252012S9R1MT 9.1±20%0.6900.53134 0.91 1.02 0.62 0.68SWPA252012S100MT 10±20% 0.6900.53134 0.79 0.88 0.62 0.68SWPA252012S120MT 12±20%1.0750.82728 0.78 0.88 0.51 0.56 SWPA252012S150MT 15±20%1.591 1.22425 0.68 0.77 0.42 0.46SWPA3010S Series Part NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat IrmsSWPA3010S1R0NT 1.0±30% 0.0850.065180 1.40 2.10 1.45 1.80 SWPA3010S1R2NT 1.2±30% 0.0850.065137 1.25 1.70 1.45 1.80 SWPA3010S1R5NT 1.5±30% 0.1040.080120 1.27 1.70 1.30 1.60 SWPA3010S2R2NT 2.2±30% 0.1430.110100 1.15 1.50 1.09 1.40 SWPA3010S2R7NT 2.7±30% 0.1690.13090 1.00 1.20 1.02 1.40 SWPA3010S3R3NT 3.3±30% 0.1890.14574 0.97 1.20 0.96 1.20 SWPA3010S3R6MT 3.6±20% 0.2150.16567 0.95 1.20 0.90 1.10 SWPA3010S4R7MT 4.7±20% 0.2930.22559 0.75 1.05 0.77 1.10 SWPA3010S5R6MT 5.6±20% 0.322 0.248 40 0.58 0.65 0.70 1.05 SWPA3010S6R8MT 6.8±20% 0.3970.30542 0.55 0.72 0.66 0.96 SWPA3010S8R2MT 8.2±20% 0.520 0.40 23 0.55 0.70 0.58 0.70 SWPA3010S100MT 10±20% 0.5200.40 39 0.55 0.75 0.58 0.70 SWPA3010S120MT 12±20% 0.6570.50536 0.43 0.65 0.52 0.67 SWPA3010S150MT 15±20% 0.7930.61030 0.42 0.57 0.47 0.57 SWPA3010S220MT 22±20% 1.2090.93028 0.35 0.48 0.38 0.52 SWPA3010S270MT 27±20% 1.404 1.08025 0.30 0.45 0.35 0.50 SWPA3010S330MT 33±20% 2.015 1.55018 0.29 0.42 0.30 0.55 SWPA3010S390MT 39±20% 2.275 1.75018 0.28 0.38 0.28 0.53 SWPA3010S430MT 43±20% 2.340 1.80 18 0.23 0.36 0.27 0.52 SWPA3010S470MT 47±20% 2.535 1.95018 0.22 0.35 0.26 0.52 SWPA3010S510MT 51±20% 2.860 2.20 18 0.21 0.33 0.25 0.48SWPA3010S560MT 56±20% 3.016 2.32016 0.21 0.280.24 0.35SWPA3012S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat Irms SWPA3012SR22NT 0.22±30% 0.022 0.017 321 5.30 6.00 3.00 3.30 SWPA3012SR82NT 0.82±30% 0.039 0.030 180 2.05 2.80 2.47 3.00 SWPA3012S1R0NT 1.0±30% 0.052 0.040 120 1.87 2.80 2.20 2.70 SWPA3012S1R2NT 1.2±30% 0.059 0.045 120 2.22 2.50 2.01 2.20 SWPA3012S1R5NT 1.5±30% 0.0590.045 110 1.62 1.90 2.01 2.20 SWPA3012S1R8NT 1.8±30% 0.0820.063 90 1.30 1.90 1.65 1.80 SWPA3012S2R2NT 2.2±30% 0.0980.075 84 1.20 1.90 1.55 1.70 SWPA3012S2R4NT 2.4±30% 0.0880.068 100 1.15 1.50 1.60 1.70 SWPA3012S2R7NT 2.7±30% 0.1100.085 65 1.14 1.50 1.48 1.50 SWPA3012S3R3MT 3.3±20% 0.1300.10 64 1.05 1.50 1.36 1.40 SWPA3012S3R6MT 3.6±20% 0.1300.10 36 1.05 1.50 1.36 1.40 SWPA3012S3R9MT 3.9±20% 0.189 0.145 61 1.00 1.30 1.24 1.30 SWPA3012S4R7MT 4.7±20% 0.1560.120 61 0.90 1.00 1.24 1.30 SWPA3012S5R6MT 5.6±20% 0.2260.17461 0.80 1.10 1.13 1.24 SWPA3012S6R8MT 6.8±20% 0.2470.190 61 0.75 0.90 0.98 1.10 SWPA3012S100MT 10±20% 0.3450.265 42 0.60 0.88 0.83 0.90 SWPA3012S120MT 12±20% 0.4490.345 32 0.48 0.67 0.73 0.84SWPA3012S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH Ω MHz A A Symbol L DCR S.R.F Isat Irms SWPA3012S220MT 22±20% 0.839 0.645 23 0.42 0.52 0.53 0.59 SWPA3012S270MT 27±20% 1.131 0.870 21 0.35 0.48 0.47 0.51 SWPA3012S330MT 33±20% 1.138 0.875 18 0.36 0.46 0.46 0.50 SWPA3012S360MT 36±20% 1.235 0.950 18 0.34 0.44 0.44 0.48 SWPA3012S390MT 39±20% 1.729 1.330 18 0.30 0.39 0.37 0.41 SWPA3012S470MT 47±20% 1.885 1.450 14 0.27 0.35 0.35 0.40 SWPA3012S560MT 56±20% 1.794 1.380 9 0.26 0.33 0.28 0.40 SWPA3012S680MT 68±20% 2.171 1.670 7 0.24 0.29 0.33 0.37 SWPA3012S820MT 82±20% 3.302 2.540 7 0.17 0.27 0.27 0.31 SWPA3012S101MT 100±20% 3.718 2.860 5 0.21 0.23 0.25 0.29SWPA3015S SeriesPart NumberInductanceDC ResistanceSelf-resonant Frequency Saturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min.Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA3015SR50NT 0.5±30% 0.039 0.030 162 3.90 4.20 2.60 2.80 SWPA3015S1R0NT 1.0±30% 0.039 0.030 150 2.32 2.80 2.35 2.50 SWPA3015S1R2NT 1.2±30% 0.052 0.040 110 2.21 3.10 1.95 2.30 SWPA3015S1R5NT 1.5±30% 0.065 0.050 100 2.30 2.70 1.70 2.20 SWPA3015S1R8NT 1.8±30% 0.065 0.050 92 1.75 2.20 1.70 2.20 SWPA3015S2R2NT 2.2±30% 0.078 0.060 86 1.60 2.00 1.60 2.00 SWPA3015S2R7NT 2.7±30% 0.098 0.075 64 1.52 1.90 1.43 1.90 SWPA3015S3R3MT 3.3±20% 0.104 0.080 68 1.32 1.81 1.36 1.60 SWPA3015S3R6MT 3.6±20% 0.137 0.105 59 1.28 1.60 1.20 1.50 SWPA3015S3R9MT 3.9±20% 0.137 0.105 47 1.20 1.40 1.20 1.50 SWPA3015S4R3MT 4.3±20% 0.150 0.115 53 1.20 1.40 1.14 1.30 SWPA3015S4R7MT 4.7±20% 0.163 0.125 46 1.10 1.40 1.09 1.30 SWPA3015S5R1MT 5.1±20% 0.173 0.133 49 1.00 1.20 1.05 1.20 SWPA3015S6R2MT 6.2±20% 0.254 0.195 46 1.00 1.20 0.86 1.00 SWPA3015S6R8MT 6.8±20% 0.260 0.20 39 0.85 1.10 0.85 1.10 SWPA3015S100MT 10±20% 0.325 0.250 41 0.72 0.92 0.77 0.90 SWPA3015S120MT 12±20% 0.416 0.320 32 0.70 0.90 0.68 0.89 SWPA3015S150MT 15±20% 0.455 0.350 30 0.66 0.88 0.65 0.72 SWPA3015S180MT 18±20% 0.559 0.430 23 0.56 0.72 0.59 0.72 SWPA3015S220MT 22±20% 0.598 0.46023 0.52 0.68 0.57 0.69 SWPA3015S270MT 27±20% 0.949 0.730 22 0.48 0.56 0.45 0.56 SWPA3015S330MT 33±20% 1.066 0.820 20 0.44 0.53 0.43 0.51 SWPA3015S390MT 39±20% 1.294 0.995 14 0.41 0.55 0.39 0.44 SWPA3015S430MT 43±20% 1.378 1.060 16 0.37 0.43 0.37 0.48 SWPA3015S470MT 47±20% 1.625 1.250 14 0.35 0.43 0.35 0.44 SWPA3015S560MT 56±20% 1.664 1.280 13 0.33 0.42 0.34 0.41 SWPA3015S620MT 62±20% 2.093 1.610 13 0.30 0.40 0.30 0.41 SWPA3015S680MT 68±20% 3.510 2.700 110.28 0.37 0.23 0.31 SWPA3015S101MT 100±20% 4.043 3.110 6.3 0.23 0.25 0.21 0.25SWPA4010S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min.Max.Typ. Max. Typ.Units μH ΩMHz AASymbol L DCR S.R.F Isat Irms SWPA4010S1R0NT 1.0±30% 0.067 0.056 116 2.00 2.30 1.90 2.40 SWPA4010S1R5NT 1.5±30% 0.084 0.070 94 1.68 2.00 1.70 2.00 SWPA4010S2R2MT 2.2±20% 0.102 0.085 73 1.20 1.50 1.50 2.00 SWPA4010S3R3MT 3.3±20% 0.120 0.10 58 1.10 1.40 1.40 1.80 SWPA4010S4R7MT 4.7±20% 0.168 0.140 47 0.95 1.10 1.20 1.50 SWPA4010S6R8MT 6.8±20% 0.240 0.20 38 0.80 0.95 1.00 1.20 SWPA4010S100MT 10±20% 0.360 0.30 31 0.62 0.75 0.75 1.00 SWPA4010S150MT 15±20% 0.516 0.43024 0.54 0.610.60 0.85 SWPA4010S220MT 22±20% 0.684 0.570 19 0.45 0.520.50 0.75SWPA4012S SeriesPart NumberInductance DC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min.Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4012SR82NT 0.82±30% 0.065 0.050 150 3.02 3.30 1.65 2.50 SWPA4012S1R0NT 1.0±30% 0.065 0.050 120 2.61 3.20 1.65 2.50 SWPA4012S1R5NT 1.5±30% 0.085 0.065 90 2.10 2.70 1.46 2.20 SWPA4012S1R8NT 1.8±30% 0.104 0.080 88 2.12 2.60 1.32 1.90 SWPA4012S2R2NT 2.2±30% 0.104 0.080 74 1.76 2.30 1.32 1.90 SWPA4012S2R7NT 2.7±30% 0.117 0.090 71 1.90 2.30 1.25 1.70 SWPA4012S3R3NT 3.3±30% 0.143 0.110 60 1.72 2.10 1.12 1.60 SWPA4012S3R6NT 3.6±30% 0.143 0.110 57 1.20 1.70 1.12 1.60 SWPA4012S4R3NT 4.3±30% 0.182 0.140 54 1.58 1.70 1.00 1.50 SWPA4012S4R7NT 4.7±30% 0.163 0.125 50 1.15 1.80 1.05 1.50 SWPA4012S5R1NT 5.1±30% 0.201 0.155 50 1.55 1.60 0.95 1.50 SWPA4012S5R6NT 5.6±30% 0.182 0.140 42 1.00 1.60 1.00 1.20 SWPA4012S6R8MT 6.8±20% 0.257 0.198 40 0.85 1.40 0.84 1.20 SWPA4012S100MT 10±20% 0.345 0.265 33 0.80 1.10 0.77 1.00 SWPA4012S120MT 12±20% 0.377 0.290 32 0.66 1.00 0.70 0.95 SWPA4012S150MT 15±20% 0.442 0.340 25 0.56 0.80 0.64 0.85 SWPA4012S180MT 18±20% 0.611 0.470 23 0.55 0.75 0.55 0.80 SWPA4012S220MT 22±20% 0.763 0.587 20 0.46 0.70 0.49 0.75 SWPA4012S270MT 27±20% 0.936 0.720 18 0.50 0.70 0.45 0.60 SWPA4012S330MT 33±20% 1.053 0.810 17 0.42 0.60 0.42 0.58 SWPA4012S360MT 36±20% 1.170 0.90 14 0.40 0.50 0.40 0.56 SWPA4012S390MT 39±20% 1.430 1.10 16 0.55 0.66 0.37 0.50 SWPA4012S470MT 47±20% 1.430 1.10 12 0.35 0.50 0.37 0.50 SWPA4012S560MT 56±20% 1.625 1.250 11 0.33 0.45 0.33 0.46 SWPA4012S680MT 68±20% 2.535 1.950 11 0.38 0.45 0.27 0.45 SWPA4012S820MT 82±20% 2.782 2.140 11 0.28 0.40 0.26 0.36SWPA4018S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4018SR47NT 0.47±30% 0.0180.014155 4.30 5.20 4.00 4.50 SWPA4018SR68NT 0.68±30% 0.0260.020128 4.90 5.60 3.30 3.80 SWPA4018S1R0NT 1.0±30% 0.0330.02580 4.80 5.20 2.00 3.30 SWPA4018S1R5NT 1.5±30% 0.0390.03065 3.35 4.00 1.80 3.20 SWPA4018S1R8NT 1.8±30% 0.0440.03454 3.00 3.40 2.00 2.80 SWPA4018S2R2MT 2.2±20% 0.0590.04552 2.70 3.20 1.65 2.60 SWPA4018S3R3MT 3.3±20% 0.0910.07044 2.45 2.90 1.23 2.10 SWPA4018S4R7MT 4.7±20% 0.1170.09034 1.70 2.20 1.20 1.80 SWPA4018S6R8MT 6.8±20% 0.1430.11029 1.45 2.00 1.06 1.50 SWPA4018S100MT 10±20% 0.2340.18024 1.30 1.60 0.84 1.20 SWPA4018S150MT 15±20% 0.3250.25019 0.94 1.10 0.65 1.00 SWPA4018S220MT 22±20% 0.4680.36016 0.80 0.88 0.59 0.85 SWPA4018S270MT 27±20% 0.6110.47027 0.47 0.62 0.52 0.90 SWPA4018S330MT 33±20% 0.6890.53012 0.56 0.75 0.49 0.72 SWPA4018S470MT 47±20% 0.8450.65010 0.57 0.70 0.42 0.65 SWPA4018S680MT 68±20% 1.30 1.0 8.3 0.47 0.51 0.32 0.52 SWPA4018S101MT 100±20% 2.275 1.750 6.5 0.40 0.44 0.25 0.41 SWPA4018S151MT 150±20% 3.250 2.50 5.5 0.31 0.34 0.22 0.36 SWPA4018S221MT 220±20% 5.20 4.0 4 0.27 0.30 0.17 0.27SWPA4020S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat IrmsSWPA4020SR24MT 0.24±20% 0.0140.011283 10.5 12.5 4.50 5.20 SWPA4020SR33NT 0.33±30% 0.0160.013223 7.50 8.50 3.30 4.90 SWPA4020SR47NT 0.47±30% 0.0290.022160 7.00 7.50 3.30 3.70 SWPA4020SR68NT 0.68±30% 0.0360.028120 6.40 6.60 2.80 3.30 SWPA4020S1R0NT 1.0±30% 0.0380.02975 4.78 5.20 2.15 3.20 SWPA4020S1R2NT 1.2±30% 0.0380.02972 5.10 5.60 2.15 3.20 SWPA4020S1R5NT 1.5±30% 0.0460.03571 4.45 4.90 1.98 3.00 SWPA4020S2R2NT 2.2±30% 0.0520.04049 3.40 3.70 1.85 2.80 SWPA4020S3R3MT 3.3±20% 0.0910.07044 3.20 3.50 1.40 2.50 SWPA4020S3R6MT 3.6±20% 0.0720.05549 2.80 3.00 1.54 2.50 SWPA4020S4R7MT 4.7±20% 0.0980.07542 2.35 2.50 1.34 2.00 SWPA4020S5R1MT 5.1±20% 0.111 0.08542 2.30 2.50 1.27 1.80 SWPA4020S5R6MT 5.6±20% 0.1170.09030 2.20 2.40 1.22 1.80 SWPA4020S6R2MT 6.2±20% 0.1500.11536 2.15 2.30 1.08 1.60 SWPA4020S6R8MT 6.8±20% 0.1630.12533 2.20 2.40 1.04 1.60 SWPA4020S7R5MT 7.5±20% 0.1500.11530 1.85 2.00 1.08 1.50 SWPA4020S8R2MT 8.2±20% 0.1630.12527 1.75 1.90 1.04 1.40 SWPA4020S100MT 10±20% 0.2150.16526 1.60 1.70 0.90 1.20 SWPA4020S120MT 12±20% 0.2280.17526 1.50 1.60 0.88 1.20 SWPA4020S150MT 15±20% 0.2990.23024 1.35 1.50 0.77 1.10SWPA4020S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4020S330MT 33±20% 0.7150.55011 0.850.930.490.68SWPA4020S390MT 39±20% 0.8450.65011 0.820.900.460.64SWPA4020S430MT 43±20% 0.8580.66010 0.770.850.450.63SWPA4020S470MT 47±20% 0.9230.71010 0.740.810.440.61SWPA4020S510MT 51±20% 0.9750.75010 0.700.770.420.59SWPA4020S560MT 56±20% 1.0400.80 10 0.660.720.410.57SWPA4020S620MT 62±20% 1.1700.90 9.6 0.650.710.390.52SWPA4020S680MT 68±20% 1.380 1.0607.7 0.610.670.360.50SWPA4020S750MT 75±20% 1.510 1.1607.7 0.700.770.350.49SWPA4020S820MT 82±20% 1.520 1.1707.2 0.500.550.340.47SWPA4020S101MT 100±20% 2.020 1.550 6.3 0.480.530.310.43 SWPA4026S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4026S1R0NT 1.0±30% 0.0310.024151 3.303.803.003.30SWPA4026S1R2NT 1.2±30% 0.0390.030120 3.103.402.303.30SWPA4026S1R5NT 1.5±30% 0.0390.030100 2.402.902.303.10SWPA4026S2R2MT 2.2±20% 0.0520.04096 2.102.402.003.80SWPA4026S3R3MT 3.3±20% 0.0650.05058 1.802.001.702.50SWPA4026S4R7MT 4.7±20% 0.0720.05546 1.451.701.602.30SWPA4026S6R8MT 6.8±20% 0.0850.06533 1.301.501.502.00SWPA4026S100MT 10±20% 0.1100.08526 1.001.201.301.90SWPA4026S150MT 15±20% 0.1430.11019 0.901.001.101.50SWPA4026S220MT 22±20% 0.2140.16513 0.600.800.901.40SWPA4026S330MT 33±20% 0.3510.2709 0.550.650.701.00SWPA4026S470MT 47±20% 0.3900.30 6 0.400.550.650.90 SWPA4030S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4030SR68NT 0.68±30% 0.0130.010130 6.80 8.00 4.56 5.10 SWPA4030SR91NT 0.91±30% 0.0170.013100 6.25 6.80 4.15 4.70 SWPA4030S1R0NT 1.0±30% 0.0180.01470 5.26 5.70 4.15 4.70 SWPA4030S1R2NT 1.2±30% 0.0200.01580 5.80 6.30 3.82 4.20 SWPA4030S1R5NT 1.5±30% 0.0260.02062 4.84 5.30 3.34 3.60 SWPA4030S1R8NT 1.8±30% 0.0330.02560 5.40 5.80 3.20 3.30 SWPA4030S2R2NT 2.2±30% 0.0390.03052 4.90 5.80 2.95 3.20SWPA4030S SeriesPart NumberInductanceDC ResistanceSelf-resonant Frequency Saturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz AA Symbol L DCR S.R.F Isat Irms SWPA4030S4R3MT 4.3±20% 0.072 0.05537 2.95 3.20 2.10 2.30 SWPA4030S4R7MT 4.7±20% 0.078 0.06031 2.90 3.20 2.00 2.30 SWPA4030S5R6MT 5.6±20% 0.085 0.06530 2.60 2.80 1.95 2.10 SWPA4030S6R8MT 6.8±20% 0.1170.09024 2.75 3.00 1.60 1.70 SWPA4030S7R5MT 7.5±20% 0.110 0.08526 2.20 2.40 1.65 1.80 SWPA4030S8R2MT 8.2±20% 0.117 0.09026 2.10 2.30 1.60 1.70 SWPA4030S100MT 10±20% 0.1300.10 21 1.95 2.40 1.50 1.60 SWPA4030S120MT 12±20% 0.1750.13518 1.70 1.80 1.30 1.40 SWPA4030S150MT 15±20% 0.2470.19016 1.65 1.80 1.11 1.20 SWPA4030S180MT 18±20% 0.2600.20 10 1.40 1.50 1.10 1.20 SWPA4030S220MT 22±20% 0.2920.22510 1.30 1.40 1.00 1.20 SWPA4030S270MT 27±20% 0.3380.26010 1.15 1.35 0.90 1.05 SWPA4030S330MT 33±20% 0.4290.33010 1.10 1.20 0.84 0.92 SWPA4030S360MT 36±20% 0.4360.3359.8 1.05 1.10 0.83 0.91 SWPA4030S390MT 39±20% 0.5660.43510 1.03 1.10 0.73 0.80 SWPA4030S470MT 47±20% 0.5790.4458.4 0.95 1.00 0.72 0.80 SWPA4030S510MT 51±20% 0.6110.4708.4 0.90 1.13 0.70 0.80 SWPA4030S560MT 56±20% 0.7220.5558.4 0.85 0.94 0.65 0.71 SWPA4030S620MT 62±20% 0.7610.5857 0.80 0.99 0.63 0.70 SWPA4030S680MT 68±20% 1.1280.8687 0.72 0.80 0.52 0.57 SWPA4030S750MT 75±20% 1.326 1.020 6.3 0.70 0.88 0.48 0.53 SWPA4030S820MT 82±20% 1.378 1.060 5.6 0.66 0.72 0.47 0.52 SWPA4030S910MT 91±20% 1.430 1.10 5.6 0.65 0.71 0.46 0.50 SWPA4030S101MT 100±20% 1.495 1.150 5.6 0.60 0.73 0.45 0.49 SWPA4030S121MT 120±20% 1.755 1.350 5.4 0.55 0.60 0.42 0.46 SWPA4030S151MT 150±20% 2.340 1.80 4 0.50 0.55 0.30 0.35 SWPA4030S221MT 220±20% 3.250 2.50 4.2 0.40 0.50 0.35 0.40 SWPA4030S331MT 330±20% 5.20 4.0 6.8 0.30 0.40 0.25 0.26 SWPA4030S471KT 470±10% 9.3607.20 2 0.30 0.35 0.20 0.23 SWPA4030S501MT 500±20% 9.027 6.9442 0.28 0.30 0.15 0.20 SWPA4030S681MT 680±20% 9.8547.580 1.2 0.190.200.14 0.18SWPA5012S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat Irms SWPA5012SR22NT 0.22±30% 0.0340.028315 8.10 9.30 3.00 3.30 SWPA5012S1R0NT 1.0±30% 0.0680.057103 4.40 4.70 2.00 2.40 SWPA5012S1R5NT 1.5±30% 0.0860.07268 3.70 3.80 1.90 2.20 SWPA5012S2R2NT 2.2±30% 0.1080.09050 3.10 3.20 1.70 2.00 SWPA5012S3R3NT 3.3±30% 0.1510.12634 2.40 2.60 1.40 1.70SWPA5012S4R7NT 4.7±30% 0.1970.16431 2.20 2.30 1.30 1.50SWPA5012S6R8MT 6.8±20% 0.2940.24522 1.70 1.90 1.00 1.20SWPA5012S SeriesPart NumberInductanceDC ResistanceSelf-resonantFrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min.Max.Typ. Max. Typ.Units μH ΩMHz AA Symbol L DCR S.R.FIsat IrmsSWPA5012S220MT 22±20% 0.858 0.780 16 0.88 0.980.60 0.68SWPA5020S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat Irms SWPA5020SR22NT 0.22±30% 0.0110.009280 9.00 12.00 5.30 6.00 SWPA5020SR24NT 0.24±30% 0.0110.009248 8.00 10.00 5.30 6.00 SWPA5020SR47NT 0.47±30% 0.0170.013160 6.15 6.70 4.60 5.00 SWPA5020SR56NT 0.56±30% 0.0220.017137 8.50 9.60 3.80 4.20 SWPA5020SR68MT 0.68±30% 0.0220.017120 5.50 6.00 4.00 4.40 SWPA5020SR75NT 0.75±30% 0.0220.017117 5.50 6.00 4.00 4.40 SWPA5020S1R0NT 1.0±30% 0.0260.020114 4.10 5.00 3.80 4.10 SWPA5020S1R2NT 1.2±30% 0.0290.02283 4.50 4.90 3.55 3.90 SWPA5020S1R5NT 1.5±30% 0.0340.02668 4.10 4.50 3.20 3.50 SWPA5020S2R2NT 2.2±30% 0.0420.03257 3.20 4.00 2.90 3.10 SWPA5020S2R7NT 2.7±30% 0.0490.03852 2.90 3.50 2.70 2.90 SWPA5020S3R0NT 3.0±30% 0.0490.03849 2.55 2.80 2.70 2.90 SWPA5020S3R3NT 3.3±30% 0.0560.04346 2.55 3.00 2.50 2.70 SWPA5020S3R6NT 3.6±30% 0.0560.04343 2.80 3.00 2.50 2.70 SWPA5020S3R9NT 3.9±30% 0.0560.04340 2.30 2.80 2.50 2.70 SWPA5020S4R3MT 4.3±20% 0.0740.05737 2.50 3.00 2.20 2.40 SWPA5020S4R7MT 4.7±20% 0.0740.05737 2.50 2.70 2.20 2.40 SWPA5020S5R1MT 5.1±20% 0.0830.06432 2.25 2.60 2.05 2.20 SWPA5020S5R6MT 5.6±20% 0.0830.06432 2.30 2.50 2.05 2.20 SWPA5020S6R8MT 6.8±20% 0.1080.08330 2.05 2.20 1.80 1.90 SWPA5020S7R5MT 7.5±20% 0.1170.09026 1.85 2.00 1.75 1.90 SWPA5020S8R2MT 8.2±20% 0.1270.09826 1.85 2.00 1.65 1.80 SWPA5020S9R1MT 9.1±20% 0.1430.11024 1.70 1.80 1.55 1.70 SWPA5020S100MT 10±20% 0.1430.11024 1.70 1.80 1.55 1.70 SWPA5020S120MT 12±20% 0.1820.14022 1.50 1.60 1.40 1.50 SWPA5020S150MT 15±20% 0.2150.16520 1.35 1.40 1.25 1.30 SWPA5020S180MT 18±20% 0.2600.20 16 1.25 1.30 1.15 1.20 SWPA5020S220MT 22±20% 0.2940.22614 1.15 1.20 1.10 1.20 SWPA5020S330MT 33±20% 0.5070.39010 0.92 1.00 0.90 0.99 SWPA5020S470MT 47±20% 0.6800.5237 0.77 0.84 0.77 0.84 SWPA5020S560MT 56±20% 0.8190.630 6 0.77 0.84 0.70 0.77 SWPA5020S680MT 68±20% 0.9620.740 6 0.65 0.70 0.64 0.70 SWPA5020S820MT 82±20% 1.1580.965 6 0.65 0.75 0.50 0.60 SWPA5020S101MT 100±20% 1.430 1.10 6 0.53 0.58 0.53 0.58 SWPA5020S121MT 120±20% 1.755 1.350 6 0.42 0.53 0.40 0.50SWPA5040S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat Irms SWPA5040SR22MT 0.22 ±20% 0.0080.006289 18.0020.00 6.50 7.50 SWPA5040SR24NT 0.24 ±30% 0.0080.006251 15.7018.00 6.40 7.40 SWPA5040SR47MT 0.47 ±20% 0.0090.007171 10.0011.50 6.60 7.60 SWPA5040S1R0NT 1.0±30% 0.0160.012117 7.35 8.00 4.90 5.00 SWPA5040S1R2NT 1.2±30% 0.0210.016110 6.50 7.00 4.15 4.25 SWPA5040S1R5NT 1.5±30% 0.0200.01586 6.30 6.80 4.30 4.85 SWPA5040S1R8MT 1.8±20% 0.0210.01655 5.50 6.05 4.15 4.30 SWPA5040S2R2NT 2.2±30% 0.0250.01950 4.90 5.50 3.80 4.20 SWPA5040S2R7NT 2.7±30% 0.0290.02237 4.30 4.80 3.60 4.00 SWPA5040S3R0NT 3.0±30% 0.0290.02237 4.15 4.60 3.60 4.00 SWPA5040S3R3NT 3.3±30% 0.0310.02432 3.95 4.45 3.40 3.90 SWPA5040S3R6MT 3.6±20% 0.0340.02630 3.80 4.40 3.30 3.70 SWPA5040S3R9NT 3.9±30% 0.0350.02729 3.55 4.00 3.20 3.70 SWPA5040S4R7NT 4.7±30% 0.0390.03028 3.50 3.80 3.00 3.30 SWPA5040S5R6MT 5.6±20% 0.0460.03527 3.00 3.70 2.80 3.10 SWPA5040S6R8MT 6.8±20% 0.0560.04321 2.90 3.40 2.50 2.80 SWPA5040S8R2MT 8.2±20% 0.0620.04820 2.70 2.90 2.30 2.60 SWPA5040S100MT 10±20% 0.0830.06418 2.35 2.70 2.10 2.35 SWPA5040S120MT 12±20% 0.1000.07714 2.2 2.5 2.0 2.1 SWPA5040S150MT 15±20% 0.1120.08613 2.00 2.20 2.00 2.05 SWPA5040S180MT 18±20% 0.1550.11912 1.70 2.00 1.45 1.65 SWPA5040S220MT 22±20% 0.1680.12911 1.60 1.80 1.50 1.60 SWPA5040S270MT 27±20% 0.2440.1889.8 1.52 1.75 1.10 1.25 SWPA5040S330MT 33±20% 0.2440.1889 1.30 1.45 1.20 1.35 SWPA5040S470MT 47±20% 0.3540.2727 1.10 1.20 1.00 1.15 SWPA5040S510MT 51±20% 0.4940.380 6 1.00 1.20 1.00 1.10 SWPA5040S560MT 56±20% 0.4940.380 6 1.05 1.20 0.80 0.90 SWPA5040S680MT 68±20% 0.5200.40 6 0.90 1.00 0.80 0.90 SWPA5040S750MT 75±20% 0.5850.450 6 0.85 0.95 0.72 0.80 SWPA5040S101MT 100±20% 0.7280.560 5 0.75 0.85 0.70 0.78 SWPA5040S151MT 150±20% 0.9750.750 3.7 0.65 0.67 0.60 0.70 SWPA5040S221MT 220±20% 1.820 1.40 3.0 0.48 0.55 0.40 0.50 SWPA5040S301MT 300±20% 2.60 2.0 2.7 0.50 0.58 0.35 0.40 SWPA5040S331MT 330±20% 2.730 2.10 2.7 0.42 0.47 0.40 0.50 SWPA5040S471MT 470±20% 3.90 3.0 2.7 0.37 0.43 0.35 0.40 SWPA5040S561MT 560±20% 4.920 3.780 1.3 0.31 0.36 0.31 0.35 SWPA5040S681MT 680±20% 5.070 3.90 1.3 0.30 0.35 0.25 0.30 SWPA5040S102MT 1000±20% 7.80 6.0 1.3 0.21 0.25 0.20 0.23 SWPA5040S332MT 3300±20% 25.2021.00.9 0.1400.150 0.100 0.120SWPA5040S392MT 3900±20% 30.5523.500.8 0.1250.150 0.100 0.115SWPA5040S472MT 4700±20% 45.5035.00.6 0.1100.130 0.080 0.100SWPA5040S502MT 5000±20% 43.1635.970.49 0.1100.130 0.085 0.098SWPA5040S562MT 5600±20% 50.7039.00.49 0.1050.120 0.080 0.092SWPA5040S682MT 6800±20% 55.9043.00.38 0.0900.110 0.0750.086SWPA5040S822MT 8200±20% 55.9043.00.38 0.0700.085 0.075 0.086SWPA5040S103MT 10000±20% 58.5045.00.32 0.0650.075 0.075 0.086。

Wire Wound SMD Power Inductors – SWPA SeriesOperating temperature range: -40℃~+125℃ (Including self-heating)FEATURES● Magnetic-resin shielded construction reduces buzz noise to ultra-low levels● Metallization on ferrite core results in excellent shock resistance and damage-free durability ● Closed magnetic circuit design reduces leakage flux and Electro Magnetic Interference (EMI) ● 30% higher current rating than conventional inductors of equal size ● Takes up less PCB real estate and save more powerAPPLICATIONS● Smart phone, smart TV, set top box, notebook ● Car navigation systems, telecomm base stations ● VR, AR ● LED lightingPRODUCT IDENTIFICATIONSWPA3012 S 1R0 N T□□□① ② ③ ④ ⑤ ⑥ ⑦②External Dimensions (L×W×H) [mm] 252010 2.5×2.0×1.0 252012 2.5×2.0×1.2 3010 3.0×3.0×1.03012 3.0×3.0×1.2 3015 3.0×3.0×1.5 4010 4.0×4.0×1.0 4012 4.0×4.0×1.2 4018 4.0×4.0×1.8 4020 4.0×4.0×2.0 4026 4.0×4.0×2.6 4030 4.0×4.0×3.0 5012 5.0×5.0×1.2 5020 5.0×5.0×2.0 5040 5.0×5.0×4.0 6020 6.0×6.0×2.0 6028 6.0×6.0×2.8 6040 6.0×6.0×4.0 6045 6.0×6.0×4.5 8040 8.0×8.0×4.0 8050 8.0×8.0×5.0 8060 8.0×8.0×6.08065 8.0×8.0×6.5 ① Type SWPAWire Wound SMD Power Inductor③ Feature TypeS Standard ④ Nominal InductanceExample Nominal Value1R0 1.0μH 100 10μH⑤ Inductance ToleranceK ±10%M ±20% N ±30% ⑥ PackingTTape Carrier Package⑦ Design Code □□□Standard product is blankFig.1 Fig.2Unit: mmSeriesShapeABCD E Fa Typ.b Typ.c Typ.SWPA252010S Fig.1 2.5±0.1 2.0±0.1 1.0 Max. 2.0±0.20.80±0.20.80±0.2 0.80 0.85 2.0 SWPA252012S Fig.1 2.5±0.1 2.0±0.1 1.2 Max. 2.0±0.20.80±0.20.80±0.2 0.80 0.85 2.0 SWPA3010S Fig.2 3.0±0.2 3.0±0.2 1.0 Max. 2.5±0.20.75±0.2 1.5±0.2 1.5 0.8 2.7 SWPA3012S Fig.2 3.0±0.2 3.0±0.2 1.2 Max. 2.5±0.20.75±0.2 1.5±0.2 1.5 0.8 2.7 SWPA3015S Fig.2 3.0±0.2 3.0±0.2 1.5 Max. 2.5±0.20.75±0.2 1.5±0.2 1.5 0.8 2.7 SWPA4010S Fig.2 4.0±0.2 4.0±0.2 1.0 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4012S Fig.2 4.0±0.2 4.0±0.2 1.2 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4018S Fig.2 4.0±0.2 4.0±0.2 1.8 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4020S Fig.2 4.0±0.2 4.0±0.2 2.0 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4026S Fig.2 4.0±0.2 4.0±0.2 2.6 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4030S Fig.2 4.0±0.2 4.0±0.2 3.0 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA5012S Fig.3 5.0±0.2 5.0±0.2 1.2 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA5020S Fig.3 5.0±0.2 5.0±0.2 2.0 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA5040S Fig.3 5.0±0.2 5.0±0.2 4.0 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA5045S Fig.3 5.0±0.2 5.0±0.2 4.5 Max. 4.0±0.2 1.30±0.2 2.5±0.2 2.3 1.4 4.2 SWPA6020S Fig.2 6.0±0.3 6.0±0.3 2.0 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA6028S Fig.2 6.0±0.3 6.0±0.3 2.8 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA6040S Fig.2 6.0±0.3 6.0±0.3 4.0 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA6045S Fig.2 6.0±0.3 6.0±0.3 4.5 Max.4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.75.7 SWPA8040S Fig.2 8.0±0.3 8.0±0.3 4.2 Max.6.3±0.3 2.00±0.3 4.0±0.3 3.8 2.27.5SWPA8050S Fig.3 8.0±0.3 8.0±0.3 5.0 Max. 6.3±0.3 2.00±0.3 4.0±0.3 3.8 2.2 7.5 SWPA8060S Fig.3 8.0±0.3 8.0±0.3 6.0 Max 6.3±0.3 2.00±0.3 4.0±0.3 3.8 2.2 7.5 SWPA8065S Fig.3 8.0±0.3 8.0±0.3 6.5 Max.6.3±0.32.00±0.34.0±0.3 3.8 2.2 7.5SHAPE AND DIMENSIONS SWPA252010S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max. Typ.Min. Max. Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCRS.R.F Isat Irms SWPA252010SR47NT 0.47±30% 0.056 0.047206 2.50 3.35 2.35 2.56 SWPA252010SR56NT 0.56±30% 0.072 0.060160 2.90 3.20 2.00 2.18 SWPA252010SR68NT 0.68±30% 0.074 0.062129 2.20 2.75 2.00 2.18 SWPA252010S1R0NT 1.0±30% 0.1080.090100 1.85 2.20 1.65 1.80 SWPA252010S1R5NT 1.5±30% 0.182 0.15281 1.80 2.10 1.30 1.42 SWPA252010S2R2NT 2.2±30% 0.209 0.17461 1.20 1.60 1.20 1.31 SWPA252010S3R3MT 3.3±20% 0.328 0.27347 1.05 1.30 0.90 0.98 SWPA252010S4R7MT 4.7±20% 0.563 0.46942 0.95 1.15 0.70 0.76 SWPA252010S5R6MT 5.6±20% 0.563 0.46935 0.80 0.95 0.73 0.80 SWPA252010S6R8MT 6.8±20% 0.896 0.74731 0.78 0.92 0.59 0.64 SWPA252010S100MT 10±20% 1.092 0.91027 0.65 0.78 0.50 0.55SWPA252012S SeriesPart NumberInductance DC Resistance Self-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH Ω MHz A A Symbol L DCR S.R.F Isat IrmsSWPA252012SR47NT 0.47±30% 0.0610.047160 3.82 4.27 2.15 2.34 SWPA252012SR68NT 0.68±30% 0.0740.057140 3.28 3.68 1.95 2.13 SWPA252012S1R0NT 1.0±30% 0.0900.069110 2.59 2.90 1.93 2.10 SWPA252012S1R2NT 1.2±30% 0.1290.099100 2.38 2.67 1.46 1.59 SWPA252012S1R5MT 1.5±20% 0.1470.11397 2.24 2.51 1.40 1.53 SWPA252012S1R5NTY01 1.5±30% 0.1300.10 63 1.80 2.00 1.45 1.58 SWPA252012S2R2MT 2.2±20% 0.2160.16669 1.85 2.07 1.15 1.25 SWPA252012S2R2NTY02 2.2±30% 0.1530.11853 1.55 1.75 1.30 1.42 SWPA252012S2R7MT 2.7±20% 0.2390.18463 1.72 1.92 1.09 1.19 SWPA252012S3R3MT 3.3±20% 0.2640.20362 1.61 1.80 1.04 1.13 SWPA252012S3R6MT 3.6±20% 0.3480.26853 1.46 1.64 0.90 0.98 SWPA252012S4R3MT 4.3±20% 0.3770.29051 1.37 1.53 0.87 0.95 SWPA252012S4R7MT 4.7±20% 0.3770.29047 1.12 1.25 0.84 0.92 SWPA252012S5R1MT 5.1±20% 0.5000.38544 1.23 1.37 0.75 0.82SWPA252012S5R6MT 5.6±20%0.5380.41438 1.11 1.25 0.73 0.80SWPA252012S6R2MT 6.2±20% 0.5420.41738 1.03 1.16 0.73 0.80 SWPA252012S6R8MT 6.8±20% 0.5810.44738 0.98 1.09 0.69 0.75 SWPA252012S7R5MT 7.5±20% 0.6110.47035 0.97 1.09 0.68 0.74SWPA252012S8R2MT 8.2±20% 0.6580.50636 0.98 1.10 0.65 0.71 SWPA252012S9R1MT 9.1±20%0.6900.53134 0.91 1.02 0.62 0.68SWPA252012S100MT 10±20% 0.6900.53134 0.79 0.88 0.62 0.68SWPA252012S120MT 12±20%1.0750.82728 0.78 0.88 0.51 0.56 SWPA252012S150MT 15±20%1.591 1.22425 0.68 0.77 0.42 0.46SWPA3010S Series Part NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat IrmsSWPA3010S1R0NT 1.0±30% 0.0850.065180 1.40 2.10 1.45 1.80 SWPA3010S1R2NT 1.2±30% 0.0850.065137 1.25 1.70 1.45 1.80 SWPA3010S1R5NT 1.5±30% 0.1040.080120 1.27 1.70 1.30 1.60 SWPA3010S2R2NT 2.2±30% 0.1430.110100 1.15 1.50 1.09 1.40 SWPA3010S2R7NT 2.7±30% 0.1690.13090 1.00 1.20 1.02 1.40 SWPA3010S3R3NT 3.3±30% 0.1890.14574 0.97 1.20 0.96 1.20 SWPA3010S3R6MT 3.6±20% 0.2150.16567 0.95 1.20 0.90 1.10 SWPA3010S4R7MT 4.7±20% 0.2930.22559 0.75 1.05 0.77 1.10 SWPA3010S5R6MT 5.6±20% 0.322 0.248 40 0.58 0.65 0.70 1.05 SWPA3010S6R8MT 6.8±20% 0.3970.30542 0.55 0.72 0.66 0.96 SWPA3010S8R2MT 8.2±20% 0.520 0.40 23 0.55 0.70 0.58 0.70 SWPA3010S100MT 10±20% 0.5200.40 39 0.55 0.75 0.58 0.70 SWPA3010S120MT 12±20% 0.6570.50536 0.43 0.65 0.52 0.67 SWPA3010S150MT 15±20% 0.7930.61030 0.42 0.57 0.47 0.57 SWPA3010S220MT 22±20% 1.2090.93028 0.35 0.48 0.38 0.52 SWPA3010S270MT 27±20% 1.404 1.08025 0.30 0.45 0.35 0.50 SWPA3010S330MT 33±20% 2.015 1.55018 0.29 0.42 0.30 0.55 SWPA3010S390MT 39±20% 2.275 1.75018 0.28 0.38 0.28 0.53 SWPA3010S430MT 43±20% 2.340 1.80 18 0.23 0.36 0.27 0.52 SWPA3010S470MT 47±20% 2.535 1.95018 0.22 0.35 0.26 0.52 SWPA3010S510MT 51±20% 2.860 2.20 18 0.21 0.33 0.25 0.48SWPA3010S560MT 56±20% 3.016 2.32016 0.21 0.280.24 0.35SWPA3012S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat Irms SWPA3012SR22NT 0.22±30% 0.022 0.017 321 5.30 6.00 3.00 3.30 SWPA3012SR82NT 0.82±30% 0.039 0.030 180 2.05 2.80 2.47 3.00 SWPA3012S1R0NT 1.0±30% 0.052 0.040 120 1.87 2.80 2.20 2.70 SWPA3012S1R2NT 1.2±30% 0.059 0.045 120 2.22 2.50 2.01 2.20 SWPA3012S1R5NT 1.5±30% 0.0590.045 110 1.62 1.90 2.01 2.20 SWPA3012S1R8NT 1.8±30% 0.0820.063 90 1.30 1.90 1.65 1.80 SWPA3012S2R2NT 2.2±30% 0.0980.075 84 1.20 1.90 1.55 1.70 SWPA3012S2R4NT 2.4±30% 0.0880.068 100 1.15 1.50 1.60 1.70 SWPA3012S2R7NT 2.7±30% 0.1100.085 65 1.14 1.50 1.48 1.50 SWPA3012S3R3MT 3.3±20% 0.1300.10 64 1.05 1.50 1.36 1.40 SWPA3012S3R6MT 3.6±20% 0.1300.10 36 1.05 1.50 1.36 1.40 SWPA3012S3R9MT 3.9±20% 0.189 0.145 61 1.00 1.30 1.24 1.30 SWPA3012S4R7MT 4.7±20% 0.1560.120 61 0.90 1.00 1.24 1.30 SWPA3012S5R6MT 5.6±20% 0.2260.17461 0.80 1.10 1.13 1.24 SWPA3012S6R8MT 6.8±20% 0.2470.190 61 0.75 0.90 0.98 1.10 SWPA3012S100MT 10±20% 0.3450.265 42 0.60 0.88 0.83 0.90 SWPA3012S120MT 12±20% 0.4490.345 32 0.48 0.67 0.73 0.84SWPA3012S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH Ω MHz A A Symbol L DCR S.R.F Isat Irms SWPA3012S220MT 22±20% 0.839 0.645 23 0.42 0.52 0.53 0.59 SWPA3012S270MT 27±20% 1.131 0.870 21 0.35 0.48 0.47 0.51 SWPA3012S330MT 33±20% 1.138 0.875 18 0.36 0.46 0.46 0.50 SWPA3012S360MT 36±20% 1.235 0.950 18 0.34 0.44 0.44 0.48 SWPA3012S390MT 39±20% 1.729 1.330 18 0.30 0.39 0.37 0.41 SWPA3012S470MT 47±20% 1.885 1.450 14 0.27 0.35 0.35 0.40 SWPA3012S560MT 56±20% 1.794 1.380 9 0.26 0.33 0.28 0.40 SWPA3012S680MT 68±20% 2.171 1.670 7 0.24 0.29 0.33 0.37 SWPA3012S820MT 82±20% 3.302 2.540 7 0.17 0.27 0.27 0.31 SWPA3012S101MT 100±20% 3.718 2.860 5 0.21 0.23 0.25 0.29SWPA3015S SeriesPart NumberInductanceDC ResistanceSelf-resonant Frequency Saturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min.Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA3015SR50NT 0.5±30% 0.039 0.030 162 3.90 4.20 2.60 2.80 SWPA3015S1R0NT 1.0±30% 0.039 0.030 150 2.32 2.80 2.35 2.50 SWPA3015S1R2NT 1.2±30% 0.052 0.040 110 2.21 3.10 1.95 2.30 SWPA3015S1R5NT 1.5±30% 0.065 0.050 100 2.30 2.70 1.70 2.20 SWPA3015S1R8NT 1.8±30% 0.065 0.050 92 1.75 2.20 1.70 2.20 SWPA3015S2R2NT 2.2±30% 0.078 0.060 86 1.60 2.00 1.60 2.00 SWPA3015S2R7NT 2.7±30% 0.098 0.075 64 1.52 1.90 1.43 1.90 SWPA3015S3R3MT 3.3±20% 0.104 0.080 68 1.32 1.81 1.36 1.60 SWPA3015S3R6MT 3.6±20% 0.137 0.105 59 1.28 1.60 1.20 1.50 SWPA3015S3R9MT 3.9±20% 0.137 0.105 47 1.20 1.40 1.20 1.50 SWPA3015S4R3MT 4.3±20% 0.150 0.115 53 1.20 1.40 1.14 1.30 SWPA3015S4R7MT 4.7±20% 0.163 0.125 46 1.10 1.40 1.09 1.30 SWPA3015S5R1MT 5.1±20% 0.173 0.133 49 1.00 1.20 1.05 1.20 SWPA3015S6R2MT 6.2±20% 0.254 0.195 46 1.00 1.20 0.86 1.00 SWPA3015S6R8MT 6.8±20% 0.260 0.20 39 0.85 1.10 0.85 1.10 SWPA3015S100MT 10±20% 0.325 0.250 41 0.72 0.92 0.77 0.90 SWPA3015S120MT 12±20% 0.416 0.320 32 0.70 0.90 0.68 0.89 SWPA3015S150MT 15±20% 0.455 0.350 30 0.66 0.88 0.65 0.72 SWPA3015S180MT 18±20% 0.559 0.430 23 0.56 0.72 0.59 0.72 SWPA3015S220MT 22±20% 0.598 0.46023 0.52 0.68 0.57 0.69 SWPA3015S270MT 27±20% 0.949 0.730 22 0.48 0.56 0.45 0.56 SWPA3015S330MT 33±20% 1.066 0.820 20 0.44 0.53 0.43 0.51 SWPA3015S390MT 39±20% 1.294 0.995 14 0.41 0.55 0.39 0.44 SWPA3015S430MT 43±20% 1.378 1.060 16 0.37 0.43 0.37 0.48 SWPA3015S470MT 47±20% 1.625 1.250 14 0.35 0.43 0.35 0.44 SWPA3015S560MT 56±20% 1.664 1.280 13 0.33 0.42 0.34 0.41 SWPA3015S620MT 62±20% 2.093 1.610 13 0.30 0.40 0.30 0.41 SWPA3015S680MT 68±20% 3.510 2.700 110.28 0.37 0.23 0.31 SWPA3015S101MT 100±20% 4.043 3.110 6.3 0.23 0.25 0.21 0.25SWPA4010S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min.Max.Typ. Max. Typ.Units μH ΩMHz AASymbol L DCR S.R.F Isat Irms SWPA4010S1R0NT 1.0±30% 0.067 0.056 116 2.00 2.30 1.90 2.40 SWPA4010S1R5NT 1.5±30% 0.084 0.070 94 1.68 2.00 1.70 2.00 SWPA4010S2R2MT 2.2±20% 0.102 0.085 73 1.20 1.50 1.50 2.00 SWPA4010S3R3MT 3.3±20% 0.120 0.10 58 1.10 1.40 1.40 1.80 SWPA4010S4R7MT 4.7±20% 0.168 0.140 47 0.95 1.10 1.20 1.50 SWPA4010S6R8MT 6.8±20% 0.240 0.20 38 0.80 0.95 1.00 1.20 SWPA4010S100MT 10±20% 0.360 0.30 31 0.62 0.75 0.75 1.00 SWPA4010S150MT 15±20% 0.516 0.43024 0.54 0.610.60 0.85 SWPA4010S220MT 22±20% 0.684 0.570 19 0.45 0.520.50 0.75SWPA4012S SeriesPart NumberInductance DC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min.Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4012SR82NT 0.82±30% 0.065 0.050 150 3.02 3.30 1.65 2.50 SWPA4012S1R0NT 1.0±30% 0.065 0.050 120 2.61 3.20 1.65 2.50 SWPA4012S1R5NT 1.5±30% 0.085 0.065 90 2.10 2.70 1.46 2.20 SWPA4012S1R8NT 1.8±30% 0.104 0.080 88 2.12 2.60 1.32 1.90 SWPA4012S2R2NT 2.2±30% 0.104 0.080 74 1.76 2.30 1.32 1.90 SWPA4012S2R7NT 2.7±30% 0.117 0.090 71 1.90 2.30 1.25 1.70 SWPA4012S3R3NT 3.3±30% 0.143 0.110 60 1.72 2.10 1.12 1.60 SWPA4012S3R6NT 3.6±30% 0.143 0.110 57 1.20 1.70 1.12 1.60 SWPA4012S4R3NT 4.3±30% 0.182 0.140 54 1.58 1.70 1.00 1.50 SWPA4012S4R7NT 4.7±30% 0.163 0.125 50 1.15 1.80 1.05 1.50 SWPA4012S5R1NT 5.1±30% 0.201 0.155 50 1.55 1.60 0.95 1.50 SWPA4012S5R6NT 5.6±30% 0.182 0.140 42 1.00 1.60 1.00 1.20 SWPA4012S6R8MT 6.8±20% 0.257 0.198 40 0.85 1.40 0.84 1.20 SWPA4012S100MT 10±20% 0.345 0.265 33 0.80 1.10 0.77 1.00 SWPA4012S120MT 12±20% 0.377 0.290 32 0.66 1.00 0.70 0.95 SWPA4012S150MT 15±20% 0.442 0.340 25 0.56 0.80 0.64 0.85 SWPA4012S180MT 18±20% 0.611 0.470 23 0.55 0.75 0.55 0.80 SWPA4012S220MT 22±20% 0.763 0.587 20 0.46 0.70 0.49 0.75 SWPA4012S270MT 27±20% 0.936 0.720 18 0.50 0.70 0.45 0.60 SWPA4012S330MT 33±20% 1.053 0.810 17 0.42 0.60 0.42 0.58 SWPA4012S360MT 36±20% 1.170 0.90 14 0.40 0.50 0.40 0.56 SWPA4012S390MT 39±20% 1.430 1.10 16 0.55 0.66 0.37 0.50 SWPA4012S470MT 47±20% 1.430 1.10 12 0.35 0.50 0.37 0.50 SWPA4012S560MT 56±20% 1.625 1.250 11 0.33 0.45 0.33 0.46 SWPA4012S680MT 68±20% 2.535 1.950 11 0.38 0.45 0.27 0.45 SWPA4012S820MT 82±20% 2.782 2.140 11 0.28 0.40 0.26 0.36SWPA4018S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4018SR47NT 0.47±30% 0.0180.014155 4.30 5.20 4.00 4.50 SWPA4018SR68NT 0.68±30% 0.0260.020128 4.90 5.60 3.30 3.80 SWPA4018S1R0NT 1.0±30% 0.0330.02580 4.80 5.20 2.00 3.30 SWPA4018S1R5NT 1.5±30% 0.0390.03065 3.35 4.00 1.80 3.20 SWPA4018S1R8NT 1.8±30% 0.0440.03454 3.00 3.40 2.00 2.80 SWPA4018S2R2MT 2.2±20% 0.0590.04552 2.70 3.20 1.65 2.60 SWPA4018S3R3MT 3.3±20% 0.0910.07044 2.45 2.90 1.23 2.10 SWPA4018S4R7MT 4.7±20% 0.1170.09034 1.70 2.20 1.20 1.80 SWPA4018S6R8MT 6.8±20% 0.1430.11029 1.45 2.00 1.06 1.50 SWPA4018S100MT 10±20% 0.2340.18024 1.30 1.60 0.84 1.20 SWPA4018S150MT 15±20% 0.3250.25019 0.94 1.10 0.65 1.00 SWPA4018S220MT 22±20% 0.4680.36016 0.80 0.88 0.59 0.85 SWPA4018S270MT 27±20% 0.6110.47027 0.47 0.62 0.52 0.90 SWPA4018S330MT 33±20% 0.6890.53012 0.56 0.75 0.49 0.72 SWPA4018S470MT 47±20% 0.8450.65010 0.57 0.70 0.42 0.65 SWPA4018S680MT 68±20% 1.30 1.0 8.3 0.47 0.51 0.32 0.52 SWPA4018S101MT 100±20% 2.275 1.750 6.5 0.40 0.44 0.25 0.41 SWPA4018S151MT 150±20% 3.250 2.50 5.5 0.31 0.34 0.22 0.36 SWPA4018S221MT 220±20% 5.20 4.0 4 0.27 0.30 0.17 0.27SWPA4020S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat IrmsSWPA4020SR24MT 0.24±20% 0.0140.011283 10.5 12.5 4.50 5.20 SWPA4020SR33NT 0.33±30% 0.0160.013223 7.50 8.50 3.30 4.90 SWPA4020SR47NT 0.47±30% 0.0290.022160 7.00 7.50 3.30 3.70 SWPA4020SR68NT 0.68±30% 0.0360.028120 6.40 6.60 2.80 3.30 SWPA4020S1R0NT 1.0±30% 0.0380.02975 4.78 5.20 2.15 3.20 SWPA4020S1R2NT 1.2±30% 0.0380.02972 5.10 5.60 2.15 3.20 SWPA4020S1R5NT 1.5±30% 0.0460.03571 4.45 4.90 1.98 3.00 SWPA4020S2R2NT 2.2±30% 0.0520.04049 3.40 3.70 1.85 2.80 SWPA4020S3R3MT 3.3±20% 0.0910.07044 3.20 3.50 1.40 2.50 SWPA4020S3R6MT 3.6±20% 0.0720.05549 2.80 3.00 1.54 2.50 SWPA4020S4R7MT 4.7±20% 0.0980.07542 2.35 2.50 1.34 2.00 SWPA4020S5R1MT 5.1±20% 0.111 0.08542 2.30 2.50 1.27 1.80 SWPA4020S5R6MT 5.6±20% 0.1170.09030 2.20 2.40 1.22 1.80 SWPA4020S6R2MT 6.2±20% 0.1500.11536 2.15 2.30 1.08 1.60 SWPA4020S6R8MT 6.8±20% 0.1630.12533 2.20 2.40 1.04 1.60 SWPA4020S7R5MT 7.5±20% 0.1500.11530 1.85 2.00 1.08 1.50 SWPA4020S8R2MT 8.2±20% 0.1630.12527 1.75 1.90 1.04 1.40 SWPA4020S100MT 10±20% 0.2150.16526 1.60 1.70 0.90 1.20 SWPA4020S120MT 12±20% 0.2280.17526 1.50 1.60 0.88 1.20 SWPA4020S150MT 15±20% 0.2990.23024 1.35 1.50 0.77 1.10SWPA4020S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4020S330MT 33±20% 0.7150.55011 0.850.930.490.68SWPA4020S390MT 39±20% 0.8450.65011 0.820.900.460.64SWPA4020S430MT 43±20% 0.8580.66010 0.770.850.450.63SWPA4020S470MT 47±20% 0.9230.71010 0.740.810.440.61SWPA4020S510MT 51±20% 0.9750.75010 0.700.770.420.59SWPA4020S560MT 56±20% 1.0400.80 10 0.660.720.410.57SWPA4020S620MT 62±20% 1.1700.90 9.6 0.650.710.390.52SWPA4020S680MT 68±20% 1.380 1.0607.7 0.610.670.360.50SWPA4020S750MT 75±20% 1.510 1.1607.7 0.700.770.350.49SWPA4020S820MT 82±20% 1.520 1.1707.2 0.500.550.340.47SWPA4020S101MT 100±20% 2.020 1.550 6.3 0.480.530.310.43 SWPA4026S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4026S1R0NT 1.0±30% 0.0310.024151 3.303.803.003.30SWPA4026S1R2NT 1.2±30% 0.0390.030120 3.103.402.303.30SWPA4026S1R5NT 1.5±30% 0.0390.030100 2.402.902.303.10SWPA4026S2R2MT 2.2±20% 0.0520.04096 2.102.402.003.80SWPA4026S3R3MT 3.3±20% 0.0650.05058 1.802.001.702.50SWPA4026S4R7MT 4.7±20% 0.0720.05546 1.451.701.602.30SWPA4026S6R8MT 6.8±20% 0.0850.06533 1.301.501.502.00SWPA4026S100MT 10±20% 0.1100.08526 1.001.201.301.90SWPA4026S150MT 15±20% 0.1430.11019 0.901.001.101.50SWPA4026S220MT 22±20% 0.2140.16513 0.600.800.901.40SWPA4026S330MT 33±20% 0.3510.2709 0.550.650.701.00SWPA4026S470MT 47±20% 0.3900.30 6 0.400.550.650.90 SWPA4030S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4030SR68NT 0.68±30% 0.0130.010130 6.80 8.00 4.56 5.10 SWPA4030SR91NT 0.91±30% 0.0170.013100 6.25 6.80 4.15 4.70 SWPA4030S1R0NT 1.0±30% 0.0180.01470 5.26 5.70 4.15 4.70 SWPA4030S1R2NT 1.2±30% 0.0200.01580 5.80 6.30 3.82 4.20 SWPA4030S1R5NT 1.5±30% 0.0260.02062 4.84 5.30 3.34 3.60 SWPA4030S1R8NT 1.8±30% 0.0330.02560 5.40 5.80 3.20 3.30 SWPA4030S2R2NT 2.2±30% 0.0390.03052 4.90 5.80 2.95 3.20SWPA4030S SeriesPart NumberInductanceDC ResistanceSelf-resonant Frequency Saturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz AA Symbol L DCR S.R.F Isat Irms SWPA4030S4R3MT 4.3±20% 0.072 0.05537 2.95 3.20 2.10 2.30 SWPA4030S4R7MT 4.7±20% 0.078 0.06031 2.90 3.20 2.00 2.30 SWPA4030S5R6MT 5.6±20% 0.085 0.06530 2.60 2.80 1.95 2.10 SWPA4030S6R8MT 6.8±20% 0.1170.09024 2.75 3.00 1.60 1.70 SWPA4030S7R5MT 7.5±20% 0.110 0.08526 2.20 2.40 1.65 1.80 SWPA4030S8R2MT 8.2±20% 0.117 0.09026 2.10 2.30 1.60 1.70 SWPA4030S100MT 10±20% 0.1300.10 21 1.95 2.40 1.50 1.60 SWPA4030S120MT 12±20% 0.1750.13518 1.70 1.80 1.30 1.40 SWPA4030S150MT 15±20% 0.2470.19016 1.65 1.80 1.11 1.20 SWPA4030S180MT 18±20% 0.2600.20 10 1.40 1.50 1.10 1.20 SWPA4030S220MT 22±20% 0.2920.22510 1.30 1.40 1.00 1.20 SWPA4030S270MT 27±20% 0.3380.26010 1.15 1.35 0.90 1.05 SWPA4030S330MT 33±20% 0.4290.33010 1.10 1.20 0.84 0.92 SWPA4030S360MT 36±20% 0.4360.3359.8 1.05 1.10 0.83 0.91 SWPA4030S390MT 39±20% 0.5660.43510 1.03 1.10 0.73 0.80 SWPA4030S470MT 47±20% 0.5790.4458.4 0.95 1.00 0.72 0.80 SWPA4030S510MT 51±20% 0.6110.4708.4 0.90 1.13 0.70 0.80 SWPA4030S560MT 56±20% 0.7220.5558.4 0.85 0.94 0.65 0.71 SWPA4030S620MT 62±20% 0.7610.5857 0.80 0.99 0.63 0.70 SWPA4030S680MT 68±20% 1.1280.8687 0.72 0.80 0.52 0.57 SWPA4030S750MT 75±20% 1.326 1.020 6.3 0.70 0.88 0.48 0.53 SWPA4030S820MT 82±20% 1.378 1.060 5.6 0.66 0.72 0.47 0.52 SWPA4030S910MT 91±20% 1.430 1.10 5.6 0.65 0.71 0.46 0.50 SWPA4030S101MT 100±20% 1.495 1.150 5.6 0.60 0.73 0.45 0.49 SWPA4030S121MT 120±20% 1.755 1.350 5.4 0.55 0.60 0.42 0.46 SWPA4030S151MT 150±20% 2.340 1.80 4 0.50 0.55 0.30 0.35 SWPA4030S221MT 220±20% 3.250 2.50 4.2 0.40 0.50 0.35 0.40 SWPA4030S331MT 330±20% 5.20 4.0 6.8 0.30 0.40 0.25 0.26 SWPA4030S471KT 470±10% 9.3607.20 2 0.30 0.35 0.20 0.23 SWPA4030S501MT 500±20% 9.027 6.9442 0.28 0.30 0.15 0.20 SWPA4030S681MT 680±20% 9.8547.580 1.2 0.190.200.14 0.18SWPA5012S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat Irms SWPA5012SR22NT 0.22±30% 0.0340.028315 8.10 9.30 3.00 3.30 SWPA5012S1R0NT 1.0±30% 0.0680.057103 4.40 4.70 2.00 2.40 SWPA5012S1R5NT 1.5±30% 0.0860.07268 3.70 3.80 1.90 2.20 SWPA5012S2R2NT 2.2±30% 0.1080.09050 3.10 3.20 1.70 2.00 SWPA5012S3R3NT 3.3±30% 0.1510.12634 2.40 2.60 1.40 1.70SWPA5012S4R7NT 4.7±30% 0.1970.16431 2.20 2.30 1.30 1.50SWPA5012S6R8MT 6.8±20% 0.2940.24522 1.70 1.90 1.00 1.20SWPA5012S SeriesPart NumberInductanceDC ResistanceSelf-resonantFrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min.Max.Typ. Max. Typ.Units μH ΩMHz AA Symbol L DCR S.R.FIsat IrmsSWPA5012S220MT 22±20% 0.858 0.780 16 0.88 0.980.60 0.68SWPA5020S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat Irms SWPA5020SR22NT 0.22±30% 0.0110.009280 9.00 12.00 5.30 6.00 SWPA5020SR24NT 0.24±30% 0.0110.009248 8.00 10.00 5.30 6.00 SWPA5020SR47NT 0.47±30% 0.0170.013160 6.15 6.70 4.60 5.00 SWPA5020SR56NT 0.56±30% 0.0220.017137 8.50 9.60 3.80 4.20 SWPA5020SR68MT 0.68±30% 0.0220.017120 5.50 6.00 4.00 4.40 SWPA5020SR75NT 0.75±30% 0.0220.017117 5.50 6.00 4.00 4.40 SWPA5020S1R0NT 1.0±30% 0.0260.020114 4.10 5.00 3.80 4.10 SWPA5020S1R2NT 1.2±30% 0.0290.02283 4.50 4.90 3.55 3.90 SWPA5020S1R5NT 1.5±30% 0.0340.02668 4.10 4.50 3.20 3.50 SWPA5020S2R2NT 2.2±30% 0.0420.03257 3.20 4.00 2.90 3.10 SWPA5020S2R7NT 2.7±30% 0.0490.03852 2.90 3.50 2.70 2.90 SWPA5020S3R0NT 3.0±30% 0.0490.03849 2.55 2.80 2.70 2.90 SWPA5020S3R3NT 3.3±30% 0.0560.04346 2.55 3.00 2.50 2.70 SWPA5020S3R6NT 3.6±30% 0.0560.04343 2.80 3.00 2.50 2.70 SWPA5020S3R9NT 3.9±30% 0.0560.04340 2.30 2.80 2.50 2.70 SWPA5020S4R3MT 4.3±20% 0.0740.05737 2.50 3.00 2.20 2.40 SWPA5020S4R7MT 4.7±20% 0.0740.05737 2.50 2.70 2.20 2.40 SWPA5020S5R1MT 5.1±20% 0.0830.06432 2.25 2.60 2.05 2.20 SWPA5020S5R6MT 5.6±20% 0.0830.06432 2.30 2.50 2.05 2.20 SWPA5020S6R8MT 6.8±20% 0.1080.08330 2.05 2.20 1.80 1.90 SWPA5020S7R5MT 7.5±20% 0.1170.09026 1.85 2.00 1.75 1.90 SWPA5020S8R2MT 8.2±20% 0.1270.09826 1.85 2.00 1.65 1.80 SWPA5020S9R1MT 9.1±20% 0.1430.11024 1.70 1.80 1.55 1.70 SWPA5020S100MT 10±20% 0.1430.11024 1.70 1.80 1.55 1.70 SWPA5020S120MT 12±20% 0.1820.14022 1.50 1.60 1.40 1.50 SWPA5020S150MT 15±20% 0.2150.16520 1.35 1.40 1.25 1.30 SWPA5020S180MT 18±20% 0.2600.20 16 1.25 1.30 1.15 1.20 SWPA5020S220MT 22±20% 0.2940.22614 1.15 1.20 1.10 1.20 SWPA5020S330MT 33±20% 0.5070.39010 0.92 1.00 0.90 0.99 SWPA5020S470MT 47±20% 0.6800.5237 0.77 0.84 0.77 0.84 SWPA5020S560MT 56±20% 0.8190.630 6 0.77 0.84 0.70 0.77 SWPA5020S680MT 68±20% 0.9620.740 6 0.65 0.70 0.64 0.70 SWPA5020S820MT 82±20% 1.1580.965 6 0.65 0.75 0.50 0.60 SWPA5020S101MT 100±20% 1.430 1.10 6 0.53 0.58 0.53 0.58 SWPA5020S121MT 120±20% 1.755 1.350 6 0.42 0.53 0.40 0.50SWPA5040S SeriesPart NumberInductanceDC ResistanceSelf-resonant FrequencySaturation Current*3Heat Rating Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A A Symbol L DCR S.R.F Isat Irms SWPA5040SR22MT 0.22 ±20% 0.0080.006289 18.0020.00 6.50 7.50 SWPA5040SR24NT 0.24 ±30% 0.0080.006251 15.7018.00 6.40 7.40 SWPA5040SR47MT 0.47 ±20% 0.0090.007171 10.0011.50 6.60 7.60 SWPA5040S1R0NT 1.0±30% 0.0160.012117 7.35 8.00 4.90 5.00 SWPA5040S1R2NT 1.2±30% 0.0210.016110 6.50 7.00 4.15 4.25 SWPA5040S1R5NT 1.5±30% 0.0200.01586 6.30 6.80 4.30 4.85 SWPA5040S1R8MT 1.8±20% 0.0210.01655 5.50 6.05 4.15 4.30 SWPA5040S2R2NT 2.2±30% 0.0250.01950 4.90 5.50 3.80 4.20 SWPA5040S2R7NT 2.7±30% 0.0290.02237 4.30 4.80 3.60 4.00 SWPA5040S3R0NT 3.0±30% 0.0290.02237 4.15 4.60 3.60 4.00 SWPA5040S3R3NT 3.3±30% 0.0310.02432 3.95 4.45 3.40 3.90 SWPA5040S3R6MT 3.6±20% 0.0340.02630 3.80 4.40 3.30 3.70 SWPA5040S3R9NT 3.9±30% 0.0350.02729 3.55 4.00 3.20 3.70 SWPA5040S4R7NT 4.7±30% 0.0390.03028 3.50 3.80 3.00 3.30 SWPA5040S5R6MT 5.6±20% 0.0460.03527 3.00 3.70 2.80 3.10 SWPA5040S6R8MT 6.8±20% 0.0560.04321 2.90 3.40 2.50 2.80 SWPA5040S8R2MT 8.2±20% 0.0620.04820 2.70 2.90 2.30 2.60 SWPA5040S100MT 10±20% 0.0830.06418 2.35 2.70 2.10 2.35 SWPA5040S120MT 12±20% 0.1000.07714 2.2 2.5 2.0 2.1 SWPA5040S150MT 15±20% 0.1120.08613 2.00 2.20 2.00 2.05 SWPA5040S180MT 18±20% 0.1550.11912 1.70 2.00 1.45 1.65 SWPA5040S220MT 22±20% 0.1680.12911 1.60 1.80 1.50 1.60 SWPA5040S270MT 27±20% 0.2440.1889.8 1.52 1.75 1.10 1.25 SWPA5040S330MT 33±20% 0.2440.1889 1.30 1.45 1.20 1.35 SWPA5040S470MT 47±20% 0.3540.2727 1.10 1.20 1.00 1.15 SWPA5040S510MT 51±20% 0.4940.380 6 1.00 1.20 1.00 1.10 SWPA5040S560MT 56±20% 0.4940.380 6 1.05 1.20 0.80 0.90 SWPA5040S680MT 68±20% 0.5200.40 6 0.90 1.00 0.80 0.90 SWPA5040S750MT 75±20% 0.5850.450 6 0.85 0.95 0.72 0.80 SWPA5040S101MT 100±20% 0.7280.560 5 0.75 0.85 0.70 0.78 SWPA5040S151MT 150±20% 0.9750.750 3.7 0.65 0.67 0.60 0.70 SWPA5040S221MT 220±20% 1.820 1.40 3.0 0.48 0.55 0.40 0.50 SWPA5040S301MT 300±20% 2.60 2.0 2.7 0.50 0.58 0.35 0.40 SWPA5040S331MT 330±20% 2.730 2.10 2.7 0.42 0.47 0.40 0.50 SWPA5040S471MT 470±20% 3.90 3.0 2.7 0.37 0.43 0.35 0.40 SWPA5040S561MT 560±20% 4.920 3.780 1.3 0.31 0.36 0.31 0.35 SWPA5040S681MT 680±20% 5.070 3.90 1.3 0.30 0.35 0.25 0.30 SWPA5040S102MT 1000±20% 7.80 6.0 1.3 0.21 0.25 0.20 0.23 SWPA5040S332MT 3300±20% 25.2021.00.9 0.1400.150 0.100 0.120SWPA5040S392MT 3900±20% 30.5523.500.8 0.1250.150 0.100 0.115SWPA5040S472MT 4700±20% 45.5035.00.6 0.1100.130 0.080 0.100SWPA5040S502MT 5000±20% 43.1635.970.49 0.1100.130 0.085 0.098SWPA5040S562MT 5600±20% 50.7039.00.49 0.1050.120 0.080 0.092SWPA5040S682MT 6800±20% 55.9043.00.38 0.0900.110 0.0750.086SWPA5040S822MT 8200±20% 55.9043.00.38 0.0700.085 0.075 0.086SWPA5040S103MT 10000±20% 58.5045.00.32 0.0650.075 0.075 0.086。

Dimensions: [mm]Scale - 4:1744777147744777147BC744777147T e m p e r a t u r eT pT L744777147Cautions and Warnings:The following conditions apply to all goods within the product series of WE-PD of Würth Elektronik eiSos GmbH & Co. KG:General:•This electronic component is designed and manufactured for use in general electronic equipment.•Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury.•Electronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer. •The component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the wire insulation may be damaged or dissolved.•Do not drop or impact the components, the component may be damaged.•Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time.•The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products also apply to customer specific products.Product specific:Soldering:•The solder profile must comply with the technical product specifications. All other profiles will void the warranty.•All other soldering methods are at the customers’ own risk.•Strong forces which may affect the coplanarity of the components’ electrical connection with the PCB (i.e. pins), can damage the part, resulting in avoid of the warranty.Cleaning and Washing:•Washing agents used during the production to clean the customer application might damage or change the characteristics of the wire insulation, marking or plating. Washing agents may have a negative effect on the long-term functionality of the product.•Using a brush during the cleaning process may break the wire due to its small diameter. Therefore, we do not recommend using a brush during the PCB cleaning process.Potting:•If the product is potted in the customer application, the potting material may shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the core. Expansion could damage the components. We recommend a manual inspection after potting to avoid these effects.Storage Conditions:• A storage of Würth Electronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment.•Do not expose the components to direct sunlight.•The storage conditions in the original packaging are defined according to DIN EN 61760-2.•The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components. Packaging:•The packaging specifications apply only to purchase orders comprising whole packaging units. If the ordered quantity exceeds or is lower than the specified packaging unit, packaging in accordance with the packaging specifications cannot be ensured. Handling:•Violation of the technical product specifications such as exceeding the nominal rated current will void the warranty.•Applying currents with audio-frequency signals may result in audible noise due to the magnetostrictive material properties.•The temperature rise of the component must be taken into consideration. The operating temperature is comprised of ambient temperature and temperature rise of the component.•Temperature rise is highly dependent on many factors including PCB land pattern, trace size, and proximity to other components.Therefore, temperature rise should be verified in application conditions.The operating temperature of the component shall not exceed the maximum temperature specified.These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable.However, no responsibility is assumed for inaccuracies or incompleteness.Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODALa004.0002023-05-30DIN ISO 2768-1mDESCRIPTIONWE-PD SMT Shielded PowerInductor ORDER CODE744777147SIZE/TYPE BUSINESS UNIT STATUS PAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODALa004.0002023-05-30DIN ISO 2768-1mDESCRIPTIONWE-PD SMT Shielded PowerInductor ORDER CODE744777147SIZE/TYPE BUSINESS UNIT STATUS PAGE。