机械专业英语21~24章

Lesson 1 Engineering Drawings1.assembly drawing 转配图2.balloon 零件序号3.detail drawing 零件图4.view 视图5.full-section view 全剖视图6.Broken-sectional view 局部视图7.Convention 惯例，规范8.Cutting-plane 剖切图9.Sketch drawing 草图10.Interchangeable 可互换的11.Craftsman 工匠，工人12.Tolerance 公差13.Procurement 采购，获得14.Exploded drawing 分解示图15.Pattern maker 模型工，翻铸工16.Machinist 机械师，机工Lesson 2 mechanics1.mechanics 力学2.Acceleration 加速度3.Deformation 变形4.Stress 应力5.Sub discipline 分支学科6.Static 静力学7.Dynamics 动力学8.Mechanics of material材料力学9.Fluid mechanics 流体力学10.Kinematics 运动学11.Continuum mechanics连续介质力学12.static equilibrium 静力平衡13.Newton’s first law14.Susceptibility 敏感性15.Newton’s second law of motion16.Yield strength 屈服强度17.ultimate strength 极限强度18.Failure by bucking 屈曲破坏19.Stiffness 刚度20.Young’s modulus 杨氏模量21.Macroscopic 宏量22.Microscopic 微量putational fluid dynamics (CFD)计算流体力学24.trajectory 轨道25.Astrophysics 天体物理学26.Celestial 天空的27.Robotics 机器人学28.Biomechanics 生物力学29.Rigid body 刚体Lesson 3 Engineering Materials1.polymer 聚合物2.Ceramics 陶瓷3.Stiff 硬的，刚性的4.Fracture 断裂，折断5.Transparent 透明的，显然的6.Lustrous 有光泽的7.Delocalized 不受位置限制的8.Ferrous 铁的，含铁的9.Nonferrous 不含铁的，非铁的10.Tailored 定制的，特制的11.Hardness 硬度12.Tensile strength 抗拉强度13.Toughness 韧性14.Quenching 淬火15.Tempering 回火16.Stainless 不锈的17.Shield 防护，屏蔽，遮挡Lesson4 Mechanical Design1.mechanism 机构，机械2.Thermal 热量，热的3.Switch 开关4.Cam 凸轮5.Valve 阀门6.Beam 梁7.Phenomena 现象8.Screw 螺钉，螺杆9.Fasteners 紧固件10.Spring 弹簧11.Gear 齿轮12.Durability 耐用性13.Femur 股骨14.Quadriceps 四头肌15.Optimization method 最优化方法16.Stiffness 硬度17.Stock 原料，备品18.Noninterference 互不干扰Lesson5 machinery component1.pulley 滑轮，带轮2.Torque 扭矩，转（力）距3.Sheave 滑轮车，槽轮4.Disassembly 拆卸分解5.Stock 棒料，库存6.Woodruff key 半圆键，月牙键7.Axle 轮轴，车轴8.Spline 花键，用花键连接9.Bushing 轴瓦，轴衬10.Involute spline 渐开线花键11.Spindle 主轴，轴12.Groove 沟，槽；刻沟，刻槽13.Residual stress 残余应力14.Coupling 联轴器15.Distortion 变形，绕曲16.Misalignment 未对准（线），非对中17.Referred to as 把。

第一章：应力与应变1.That branch of scientific analysis which motions, times and forces is called mechanics and is made up of two parts, statics and dynamics.研究位移、时间和力运动乘力是科学分析法的一个分歧，被称作力学，力学由两大部分组成，静力学和动力学。

2.For example, if the force operating on a sleeve bearing becomes too high, it will squeeze out the oil film and cause metal-to-metal contact, overheating and rapid failure of the bearing.例如：如果止推轴承上的作用力过大的话，会挤出油膜，引起金属和金属之间的相互接触，轴承将过热而迅速失效。

3.Our intuitive concept of force includes such ideas as place of application, direction, and magnitude, and these are called the characteristics of a force.力的直观概念包括力的作用点、大小、方向，这些被称为力的三要素。

4.All bodies are either elastic or plastic and will be deformed if acted upon by forces. When the deformation of such bodies is small, they are frequently assumed to be rigid, i.e., incapable of deformation, in order to simplify the analysis.所有的物体既可以是弹性的也可以是塑性的，如果受到力的作用就产生变形。

序号中文1机械的，力学的，呆板的，无意识的，手工操作的2机械性能，力学性质3机械设备4机械工程，机械工程学5力学模型，机械式模型6机械强度7机械设计，构造设计，机械设定8机械特性，力学特征，机械行为9机械结构10机械密封11机械分析，粒度分析12机械系统，力学系统，力学体系13机电产品14机械通风，强制通风15机械传动，机械性传播16机械装置17机械能18机械振动19机械工程师20机械制图，机械图21机械合金化22车辆维修，车辆补缀23机械表24设备层25机械试验，机械性能试验，力学试验，力学性能试验26机械植绒，机械植毛27机械运动，力学运动28机械抛光，机械研磨29机械零件，机器零件英文mechanicalmechanical propertymechanical equipment mechanical engineering mechanical modelmechanical strengthmechanical designmechanical behaviormechanical structure mechanical sealmechanical analysismechanical systemmechanical and electrical products mechanical ventilation mechanical transmission mechanical devicemechanical energymechanical vibrationmechanical engineermechanical drawingmechanical alloyingmechanical Helpmechanical watchmechanical floormechanical testmechanical flockingmechanical motionmechanical polishing mechanical Elements。

《机械工程专业英语》词汇Chapter One Mechanics Components 第一章机械构件 Lesson One 第一课齿轮 Words and Expressions1.spur gear 直齿轮2.thermal expansion 热膨胀3.lubrication润滑4.backlash倾向间隙5.the pitch circles节圆6.space width间隙宽度7.instrument gear仪表齿轮8.the split gear拼合齿轮9.helical gear斜齿轮10.pitch-line velocities节线速度11.an axial thrust轴向推力12.blank 坯件13.double-helical gears 人字齿轮14.non-intersecting不相交的15.worm gears蜗轮蜗杆16.bevel gears伞齿轮17.crossed-axis交叉轴18.nut 螺母19.screw丝杠螺钉rge rations 大速比21.parallel-shaft gears平行轴齿轮22.single-thread worms单线蜗杆23.lead angles导角24.multiple-thread worms多线蜗杆25.hypoid gear偏轴伞齿轮26.rolling Cones滚锥27.involutes渐开线，Lesson Two Rolling Guides and Bearings 第二课滚动导轨和轴承Words and Expressions1.rolling guides (rolling guideways) 滚动导轨2.plain guides普通导轨3.a roller chain滚柱链4.cape保持架5.guide surfaces导轨面6.stiffness 刚性7.load-carrying capacity 载荷能力8.rolling-contact bearings滚动轴承9.ball bearing球轴承10.an inner race 内座圈11.an outer race外座圈12.separator 隔离环13.curvature曲率14.notch 凹槽15.thrust load 推力负载16.a radial ball bearing经向球轴承17.sections断面18.an axial-thrust bearing轴向推力轴承19.washer 垫圈20.roller bearing 滚子轴承21.tapered 锥形的22.spherical球面的23.retaining shoulder 定位肩24.needle bearing滚针轴承25.tapered roller bearings锥形滚子轴承26.spherical roller bearings 球面滚子轴承27.concave凹面的28.convex凸面的Lesson Three Clutches第三课离合器Word and Expressions1.coaxial (coaxial) 同轴的，共轴的2.a rotatable shaft (driven shaft) 从动轴3.a rotating shaft (driving shaft) 主动轴4.friction clutches磨擦离合器5.ring-shaped环形的6.spring弹簧7.a conical spool锥形短管轴8.coefficient of friction磨擦系数9.facing衬片10.dry clutches干式离合器11.wet clutches 湿式离合器12.a multiple-plate disc clutch多片式圆盘离合器13.spline花键14.pivot枢轴15.magnetic clutches电磁离合器16.an annular gap环状间隙17.powder iron铁粉18.graphite石墨19.direct-current control coil直流控制线圈20.slippage滑动Lesson Four Ball screw and nuts 第四课滚珠丝杠螺母副Words and Expressions1.precision ball screw assembly 精密滚珠丝杠副2.auto-drafting machines自动制图机3.valves阀门4.metallurgical machinery冶金机械5.satellite tracers卫星跟踪仪6.steering gears转向机构7.stick-slip 爬行循环8.rolling guideways滚动导轨9.recirculating-ball screw滚珠丝杠10. feed mechanisms 进给机构11. wear 磨损12. damping property 阻尼性13. tangential 切向的14. circumferential 圆周的15. thread pitch螺距16. a ball-return track回珠滚道17. a return tube回珠管18. shock-free无冲击19. stiffness刚性20. freedom from免除21. pre-load预载Chapter Two Constructure and Technology of Machine Tools第二章机床结构及工艺Lesson One Size, Bed and Tailstock of Engine lathe第一课普通车床的尺寸、床身及尾架Words and Expressionsthe (turning lathe, engine lathe, tuning machine) 车床2.the live center point 活顶尖3.swing 回转直径4.bed 床身5.ways导轨6.Carriage 床鞍7.Cross-feed slide 横进给刀架8.Headstock主轴箱9.tailstock. 尾架10. rack 齿条11. pinion gear小齿轮12. handwheel 手轮13. hardened steel 淬火钢14. flame-hardened ways 火焰淬火导轨15. the distance between centers项尖距16. taper shank锥形车削17. tailstock spindle 尾架锥柄18. taper shank 套筒19. three-jaw chuck三爪卡盘20. roller bearing滚子轴承21. lubrication润滑22. workpiece工件Lesson Two Headstock of Engine Lathe第二课普通车床的主轴箱Words and Expressions1.spindle 主轴2.taper sleeve锥套3.live center轴心活顶针4.the threaded spindle nose螺纹主轴头5.the cam lock spindle nose凸轮锁紧主轴头6.the long taper key drive spindle nose长锥键传动主轴头7.flange法兰盘8.Chuck卡盘9.Cam lock stud、凸轮锁紧短轴10. Collar 轴环11. faceplate套圈12. keyway花盘，键槽13. back gear背轮14. bull gear 大齿轮15. sliding pit滑动槽16. groove、槽17. step pulley塔轮18. drive pulley主动轮19. driven pulley被动轮20. gear box齿轮变速箱Lesson Three Carriage, Feeding and Threading Mechanism of Engine Lathe第三课普通车床的床鞍、进给和车螺纹机构 Words and Expressions1.Saddle鞍座2.Apron 滑板箱3.Cross slides 横向滑板，横刀架pound rest 复合刀架（转盘）5.tool post小刀架6.tool holder 刀夹7.Clutch 离合器8.Facing 车端面9.Cutoff 切断机动进给10. power feed 动力进给11. split nut (half-nut) 开合螺母12. dovetail way 燕尾导轨13. micrometer collar 千分尺套圈摇柄14. rocker 摇臂15. threading 车螺纹16. gear box 齿轮箱，传动箱17. ring collar 刻度环18. an index chart 指示图19. lead screw丝杠20. feed rod 光杠21. Cross-feed横进给22. Longitudinal feed 纵向进给23. acme threads 梯形螺纹24. right-hand thread右旋螺纹25. left-hand thread 左旋螺纹Lesson Four Word-holding attachments for the lathe and Rough turning第四课车床工件夹紧附件和粗车Words and Expressions1.attachment 附件2.four-jaw independent chuck 四爪单动卡盘3.Collar chuck 套爪卡片4.follower rest 跟刀架5.reducing sleeve 中心架the dog 异径套筒7.bent-tail dog 车床卡爪8.Rough turning 曲尾卡爪9.Rough turning粗车white lead白铅粉Center height中心高end副后角relief后角Clearance angle留隙角 back rake 纵向前角tangent切线caliper卡尺trial cut试切overload过载、Lesson Five Milling Shaper, Planer and Grinding Machines第五课铣床、刨床和磨床Words and Expressionsling machines 铣床ling cutter 铣刀刀杆3.arbor 心轴4.spacer 垫圈、垫片5.bushing套6.yoke 支座7.starting lever 起动手柄8.Knee升降台9.elevating screw 升降丝杆10. index head分度头11. foot stock 分度头支座12. Universal Milling Machine 万能铣床13. Shaper牛头刨床14. plane 龙门刨床15. ram 滑轨16. vise 台钳17. fixture 夹具18. notched wheel or ratchet 棘轮19. pawl 棘爪20. cross rail 横梁21. grinding machine 磨床22. grinding wheel 砂轮23. finish 光洁度24. Cutter grinder 工具磨床25.surface grinder 平面磨床26.centreless grinder 无心磨床27.internal grinder 内圆磨床28.external grinder 外圆磨床29.Wheel head磨头Lesson Six Machine Tool Tests, Accuracy checking and Maintenance 第六课机床试验，精度检验及保养Words and Expressions1.acceptance tests 验收试验2.certificate data 检验证数据3.geometrical accuracy几何精度4.surface roughness 表面粗糙度5.vibration-proof 防振6.straightness 平直度7.flatness 平面度8.upright立柱9.base plate 底板10. deviation 偏差11. parallelism 平行度12. squareness垂直度13. servicing 维修14. inspection检查15. repairs 检修16. maintenance 保养17. rapidly wearing components 易损件18. post-inspections repairs 后检查修理19. periodic repairs定期检修20. routine servicing 日常维修21. general overhaul 大修22. restoration修复Chapter Three Modern Manufacturing Engineering &Development第三章现代制造技术及其发展Lesson One The development of NC 第一课数字控制的发展 Words and Expressions1.vacuum tube 真空管2.electrical relay 继电器3.interface 接口4.integrated circuit(IC) 集成电路5.hardware 硬件6.Read Only Memory(ROM) 只读存储器7.Machining Center 加工中心8.Turning Center车削中心9.electrical discharge machining电火花加工10.drafting制图11.printed circuit(PC) 印刷电路12.robot机械手，机器人13.Subroutine子程序14.tape reading纸带读数15.alarm 报警16.diagnostic message诊断信息17.Constant surface speed control 恒线速控制18.polar coordinate 极座标19.interpolation插补20.microprocessor微处理机21.servo drive伺机服驱动22.pre-amplifier前置放大器23.point-to-point点位24.contouring轮廓控制25.bubble memory磁泡存储器26.macro宏指令27.canned cycle固定循环Lesson Two Open-loop and closed-loop servo drives第二课开环和闭环伺服驱动Words and Expressionsrmation command section 信息命令段2.punched tape code穿孔带码3.magnetic tape code 磁带码4. input data 输入数据5.open-loop开环6.closed-loop 闭环7.automatic washing machine自动洗衣机8.power supply level电源电平9.feedback 反馈10. resolution清晰度11. deterioration恶化，变坏12. discrepancy差误13. subtract logic减法逻辑14. command position counter 指令位置计数器15. drive signal amplifier 伺服信号放大器16. transducer 传感器17. synchro 同步机18. shaft digitizer轴数字读出器19. analog模拟量digital数字式self-correcting自动修正light interruption光中断photo cell光电管electric pulse电脉冲increment增量encoder编码器binary二进制Gray code格雷码Segmentation扇区Lesson Three Hydraulic motors and servo motors第三课液压马达和伺服电机Words and Expressions1.hydraulic motor 液压马达2.oil sump 油箱，油槽3.oil pressure pump 油压力泵4.hydraulic cylinder 液压缸5.valve 阀6.oil flow 油流7.hydrostatic drives 水力驱动，静压驱动8.variable-delivery pump9.piston 活塞10. reciprocating movement 往复运动11. supply line 供应线12. return line 回程线13. the filling cycle14. servomotors 伺服电机15. input command signals 输入命令符号16. step-by-step motors 步进电机17. Phase-shifted18. Amplifier 放大器19. Contact 触点，接头20. Electromagnet 电磁铁。

Lesson 1 Basic Concepts in Mechanics机械学的基本概念mechanics n.力学modify v.修改，调解，变更manageable a.可控制【管理】的incline v.（使）倾斜ramp n.斜板，斜坡【道】slope v.（使）倾斜friction n.摩擦roll v.滚动multiplier n.放大器，乘法器broom n.扫帚convert v.转变【化】handle n.手柄【把】sweep v.扫荡【描】，掠过efficiency n.效率gauge vt.测【计】量，校验bearing n.轴承ideal mechanical advantage 理想的机械效益neglect vt.忽略Lesson 2 Basic Assumption in Plasticity Theory 塑性理论的基本假设assumption n.假定plasticity n.塑性investigate v.调查，研究deformation n.变形metal forming process 金属成型工艺【过程】strain (rate) n.应变【速率】strength n.强度stress n.应力yield stress 屈服应力flow stress 流动应力tensile stress 拉【伸】应力compressive stress 压【缩】应力shear stress 剪【切】应力geometry n.几何形状elastic a.弹性的springback n.回弹bending n.弯曲，折弯precision forming 精密成型tolerance n.公差continuum n.连续（体）metallurgical a.冶金（学）的grain n.晶粒dislocation n.位错（uni-,tri-,multi-）axial a.（单，三，多）轴（向）的anisotropy n.各向异性cylindrical a.圆柱体的cross-section n.横截面platen n.（工作）台板，模板coincide with 一致，相符validity n.正确有效，合法with ease 轻（而）易（举）的，很容易的Lesson 3 Optimization for Finite Element Applications有限元优化的应用optimization n.优化，优选（法）finite element 有限元iterative a.反复的，迭代的alternative n.a.交替（的），可供选择的manual a.手动的，人工的trial-and-error 试凑法bias vt,n.（使）偏向【重、差】a desktop platform （计算机）桌面平台constrain(t) v,n.强制，约束response n.反【响】应，灵敏度parameter n.参数parametric a.参数的preprocess vt.预（先）加工，预处理mesh n,v.网格，啮合capability n.能力，性能，容量loop n.环，回路，循环pose v.提出model n.模型，样品displacement n.位移，排量，替换buckling n.弯【翘】曲，挠度factor n.因素gradient n.坡【梯】度，斜率flur n.【电，磁，热，光】通量，流量multidisciplinary a.多学科的deflection n.偏移【转，离】，挠曲Lesson 4 Metals 金属toughness n.韧性corrosion n.腐蚀dump v.倾倒，堆放recyle v.反复【循环】利用copper n.铜aluminum n.铝bronze n.青铜（器）alloy n.合金wear v.磨损metallic a.（含）金属（制）的specification n.操作规程，技术要求，说明书extract vt.提炼，萃取iron n.铁carbon n.碳ferrous a.（含）铁的ferrous metals 黑色金属lead n.铅zinc n.锌tin n.锡ore n.矿（石）mineral n,a.矿物（的）impurity n.杂质，不纯Lesson 5 Metallic and Nonmetallic Materials金属和非金属材料magnesium n.镁nickel n.镍brass n.黄铜luster n.光泽ductility n.延展性，可锻性it is likely that 很可能it is certain to (inf.)必然，一定density n.密度be distinguished from 与…区分coefficient n.系数in connection with 关于，与…相关【结合】category n.种类hardness n.硬度elasticity n.弹性beam n.横梁，一束（光）penetration n.贯穿，渗透abrasion n.磨损【耗】roll n,v.轧辊，滚，轧mill n.轧钢机，铣床spring n.弹簧permanent a.永久的rupture n.破【开】裂stamp n.冲压hammer n.（锻）锤Lesson 6 Plastics and Other Materials塑料和其他材料inorganic acid 无机酸sulphuric acid 硫酸hydrochloric acid 盐酸solvent n.溶剂carbon tetrachloride 四氯化碳rigid a,n.坚硬的，刚性（的），刚度mould(mold) n.模子，塑模，铸模decoration n.装饰fabricate vt.制造【备】，生产injection molding 注射模塑（法）blow molding 吹塑（法）compression molding 压塑（法），模压（法）extrusion n.挤压vacuum forming 真空模塑（法）powder metallurgy 粉末冶金constituent n,a.组成【的，部分】，组元simultaneously adv.同时subsequently adv.随后coherent a.互相凝聚的，协调一致的fusion n.熔化，熔接crystalline n,a.结晶【的】，晶体【的】restriction n.限制【定】，节流blend n,v.混合【物】，融合press n,v.压力机，压制homogeneous a.均匀的sinter n,vt.烧结【物】Lesson 7 Die Life and Die Failure模具的寿命和失效die n.模具，锻【冲】模，凹模die life 模具寿命die failure 模具损坏deterioration n.变坏，退化，损耗surface finish 表面光洁度breakdown n.破坏，击穿lubrication n.润滑cracking n.裂纹breakage n.断裂mode n.方式，状态，模式thermal fatigue 热疲劳layer n.层abrasive n,a.（研）磨料（的），磨损（的）impression n.模膛，型腔（槽）heat checking 热裂纹，龟裂steep n,a.陡（坡）的，急剧的reversal n.颠倒，相反overload n,v.（使）过【超】载initiation n.开【初】始，发【产】生discrete a.不连续的，单个的variable n.变量cavity n.模膛，型槽stock n.坯料，原材料impact n,v.冲击，碰撞Lesson 8 Cold Working and Hot Working 冷加工和热加工cold[hot] working 冷热加工forging n.锻造，锻件classification n.分类recrystallization n.再结晶take place 发生strain [deformation] hardening 应变【变形】硬化be referred to as 叫做，称为，被认为是warm working 温加工，温锻ultimate a,n.最终的，首要的，极限stress relieving 消除应力处理austenitic a.奥氏体的stainless steel 不锈钢annealing n.退火grain size 晶粒度solid solution 固溶体refinement n.精炼【制】，细化hazard n.危险，未知数，意外事件inherent a.固有的，先天的，本质的sensitive a.灵敏的，敏感的abnormal a.非正常的critical strain 临界应变Lesson 9 Casting 铸造casting n.铸造【件】die-casting n.模铸【件】foundry n.铸造【车间】pour v.浇注suitability n.适应性pig iron 生铁cupola n.冲天炉，化铁炉erosion n.腐蚀，（侵、烧）蚀ladle n.铁水包graphite n.石墨solidify v.（使）凝固disjoin v.拆散，分开ingot n.（钢）锭destructive a.破坏（性）的，有害的retard vt,n.（使）延缓，推迟solvent n,a.溶剂（的）copper-base alloy 铜基合金Lesson 10 Metal Forming Processes in Manufacturing 制造中的金属成形工艺machine-building 机械制造plastic working 塑性加工billet n 坯料，锻坯blank n.坯料，（冲压）板坯configuration n.外形，配置，排布stroke n.行程，冲程amortize v.阻尼，缓冲，分期偿还reliability n. 可靠性，安全性drawing n.（锻坯）拔长，【线，管材】拉拔deep drawing 深冲（压）brake forming 【压】折弯（机）成型stretch forming 张拉成型military n,a.军队【事，人】（的）consumer goods 消费品integrity n.完整性，完全（善）jet engine 喷气发动机turbine n.涡【汽】轮（机），透平（机）regarding 考虑到，关于Lesson 11 Forging锻造armor n.铠甲immortalize vt.（使）不朽（灭）blacksmith n.锻工mechanical press 机械压力机hydranlic press 液压机anvil n.（锤）砧，砧座craftsman n.技工handling n.处理，装卸，搬运flexibility n.柔（韧）性，灵活性drawn out 拔长upset n.镦粗，顶锻closed impression die 闭式模锻rapid-impact blow 快速冲击，猛打vertical a.立式的ram n.锤头，滑块，活动横梁block n.（模）块draft n.模锻斜度symmetrical a.轴对称的sizing n.整形，校正，定径drop forging 落锻，锤模锻impression die forging 模锻final forging 终锻overheat n.过热furnace n.【熔，高】炉pyrometer n.高温计Lesson 12 Benefits and Principles of Forging锻造的优点和工作原理metalworking n.金属压力加工knead v.揉搓【制】refine v.精炼【制】，细化porosity n.多孔性，疏松orient v.（使）定【取】向flow line 流线stress field 应力场manual skill 手工技巧at one’s command 自由使用，支配soundness n.致密性，坚固性，无缺陷attainable a.可达【得】到的open die forging 自由锻gross n.总共，重大confine vt. 限制，约束convert v.转变【换】，更换broken up 破【断】裂，分散microshrinkage n.显微缩孔elimination n.消除，淘汰align v.调整，对中，校直Lesson 13 Welding焊接weld(ing) v,n.焊接，熔焊pressurewelding 压力焊spotwelding 点焊buttwelding 对头（缝）焊fusionwelding 熔焊，熔接fiux-shielded arc welding 熔剂保护电弧焊diversity n.不同多样性fasten(ing) v,n.连接（件），紧固（件）shielding n.遮护，屏蔽solder(ing) v,n.软钎焊，（低温）焊料bismuth n.铋cadmium n.镉rivet n,v.铆钉，铆接braze n,vt.硬钎焊，铜焊oxidation n.氧化flux n.焊接，助溶剂squeeze v.挤压oxy-acetylene n,a.氧（乙）炔（的）torch n.焊炬electrode n.电（焊）极，焊条filler n.填充（剂）overlap v.搭接，重叠strike v.攻【打】击，放电Lesson 14 Heat Treatment热处理heat treatment 热处理microstructure n.显微组织low-carbon steel 低碳钢prescribe v.规定，指示microscopic a.显微的，微观的spheroidizing n.球化（处理）normalizing n.正火，（正）常化annealing n.退火hardening n.淬火tempering n.回火soaking(=holding) n.均热，保温retarding media 延缓介质prolonged a.长时间的，持续很久的critical temperature 临界温度globular a.球形（状）的carbide n.碳化物，硬质合金quenching n.淬火，骤冷removal n.除去，放出Lesson 15 Introduction to Mechanism机构介绍mechanism n.机械，机构，机构学kinematic a.=kinematical 运动的，运动学的kinematic chain 运动链link n.构件，杆件. v.连接【结】definite a.确定的constrained a.约束的，限定的unconstrained a.无约束的linkage n.连杆（组，机构）joint n.结【接】台，铰链. a.连接的，联合的pin n.销【钉】，铰销revolution v.旋转，转动. n.回转体prismatic a.棱柱（形）的nonlinear a.非线性的four-bar linkage 四杆机构kinematic chain 运动链prime mover 原动者【机】，驱动件coupler n.连接件，连杆pivot n.枢（轴），轴销，回转副，旋转中心configuration n.外形，构造，结构inversion n.转换，更换slider-crank mechanism 曲柄滑块机构multiloop n.多环链，a.多回路的sketch n.草【简，示意】图，v.画草图，草拟skeleton diagram 草图，示意图，简图envision v.想象binary a.二【双，复】的，二元的ternary a.三元的ternary links 三杆组quaternary a.四元的quaternary links 四杆组cam 凸轮cam follower n.凸轮从动件gear n.齿轮sprocket n.链轮belt n.【皮，布，钢】带pulley n.带轮spherical a.球的，球面的helical a.螺旋的three-dimensional 三维的，空间的intuitively adv.直觉【观】地synthesis n.合成（法），综合kinematician n.运动学研究者（家）innate a.先天的，固有的Lesson 16 Movement Analysis 运动分析criterion(pl.criteria) n.（判断）标准，判据，准则branch n,v.分（部，支）transmission angle 传动角rock n.摆动，v.摇动oscillate v.摆动，摇动parallelogram n.平行四边形antiparallelogram n.反平行四边形frame n.机架，构架impart v.给予，分给to impart M to N 把M给Ntorque n.力矩，扭矩dynamic a.=dynamical 动力的，动力学的inertia n.惯性（物），惯量static a.=statical 静力【学】的，静的index n.指数，指标friction n.摩擦thumb n.拇指，v.用拇指翻rule of thumb 根据经验和实际所得的做法matrix n.矩阵determinant n.行列式derivative n.导数derivative of M with respect to N M对于N的导数movability n.可动性，易动性parameter n.参数discount v.打折扣，忽视absolute a.绝对的graphical a.图形的，图解的polygon n.多边形theorem n.定理stress n.应力bearing n.轴承centripetal a.向心的Lesson 17 Kinematic Synthesis运动的综合packaging machinery 包装机械lubrication n.润滑specification n.技术要求actuation n.驱动jerk n.震动，冲击axis n.(pl.axes)轴【线，心】，中心线contour n.外形，轮廓线eccentricity n.偏心【度，率】gear ration 齿轮【速，齿数】比topologically adv.拓扑学地customary a.通常的，习惯的correlate v.使相关，使发生关系analog n.=analogue 类似（物），模拟linear analog 线性模拟second acceleration 二阶加速度higher acceleration 高阶加速度paraphrase v.释义，意译describe v.叙述，描述，作…运动category n.种类，类别deliberation n.慎重考虑province n.省，领域preconceive v.预想，事先想好analog computer 模拟计算机trace v.追踪，描画timing n.定时，计时，配时pitch v.投掷trajectory n.轨迹embed v.嵌入，夹在层间orientation n.（定）方位，（取）方向scoop n.勺子，铲斗，v.挖，掘，铲Lesson 18 Cams and Gears凸轮和齿轮cam n.凸轮gear n.齿轮curve n.曲线a.弯曲的groove n.槽，沟mate v.配合，啮合cylindrical a.圆柱的two-dimensional or planer 两维的或平面的three-dimensional or spatial 三维的或空间的normal n.法线a.垂直的complement n,a.余角，余的collinear a.共线的lateral a.横向的，侧向的stem n.杆guide n.导向件【器，装置】，导槽（座）intermittent a.间断的，不连续的dwell n,v.停止，小停顿inertial a.惯性的，惯量的engage v.啮合rack n.齿条noncircular a.非圆的conjugate a.共轭的，n.共轭值（线）cycloidal a.摆线的involved a.渐开线的，n.渐开线tolerance n.间隙，公差spur gear 直齿圆柱轮radial a.径向的，沿半径的offset n,vt.偏移，偏心a.偏心的disk cam 盘形凸轮tangent n.切线a.相切的，切线的concentric a.同圆（的），同心（的）camshaft n.凸轮轴pitch curve 节线herringbone a.人字形的intersect v.横穿，相交parallel helical gear斜齿轮，平行轴螺旋齿轮crossed helical gear 交错轴螺旋齿轮face gear 端面齿轮spiral bevel gear 螺旋齿圆锥齿轮worm n.蜗杆skew bevel 斜齿圆锥齿轮hypoid gear 准双曲面（直角交错轴双曲面）齿轮addendum (pl.addenda) n.齿顶，齿顶高project v.伸出，突出clearance n.间隙dedendum (pl. dedenda)n.齿根，齿根高tooth space 齿间距backlash n.间隙，齿隙Lesson 19 Screws, fasteners and joints螺纹件、紧固件和联接件screw n.螺钉，螺丝，v.旋紧，攻丝fastener n.紧固件joint n.连【联】接，接合bolt n.螺栓nut n.螺母cap screw 有头螺钉setscrew n.定位【固定，调整】螺钉rivet n.铆钉，v.用铆钉铆接key n.键weld n,v.焊接，熔焊braze n,v.钎焊，铜焊clip n.夹子，v.夹住，夹紧synonymous a.同意义的monotonous a.单调的taint n.污点，污染v.弄脏tough a.坚韧的ductile a.可延伸的，有延展性的，韧性的tighten v.上紧，拉紧twist v.扭转jumbo n.大型喷气式客机titanium n.钛close-tolerance 高精密度的tooling n.工具，刀具v.用刀具（切削）加工proliferate v.增殖，增殖assembly n.安装，装配，组件tap n.丝锥，v.攻螺丝stud n.双头螺栓resemble v.类似，像thread n.螺纹（线），v.车螺纹drill n,v.钻孔hexagon head 六角头fillister n.凹槽flat head 平头hexagon socket head 六角沉头disassemble v.拆开tensile a.拉【张】力的，受拉的shear n.剪切【力】v.剪切【断】harden v.使硬【化】washer n.垫圈preload n.预载荷fatigue n.疲劳micrometer n.千分尺，千分表elongation n.拉【伸】长modulus n.(pl.moduli)模数，模量wrench n.扳手dial n.刻度盘fractional a.分数的，小数的Lesson 21 Helical, Worm and Bevel Gears 斜齿轮、蜗杆蜗轮和锥齿轮helical gear 斜齿轮worm n.蜗杆，螺杆bevel gear 圆锥齿轮helix n,a.(pl. helices 或helixes)螺旋线，螺旋线的right hand 右手，右旋的helicoid n.a.螺旋【面，体】，螺旋（状，纹）的wrap v.缠绕unwind v.解开，展开generate v.产生，展成（加工）engagement n.啮合，接触diagonal n,a.对角线（的）objectionable a.该反对的，不能采用的spiral n,a. 螺旋线（的），卷线（的）spiral gear 螺旋齿轮mesh n.啮合worm gear 蜗轮pinion n.小齿轮pitch cylinder 节圆柱concave a.中凹的curvature a.曲率screw-like 像螺丝（杆）的thread n.线状物，螺纹线envelop v.包围，封闭enclose v.包围lead angle 导角cast v.铸造mill v.铣削outboard a,ad.外侧的，向外pronounced a.明确的，显著的stress n.应力tapered a.锥形的positively ad.确定地，强制（传动）地Pitch-line velocity 节线速度automobile differential 汽车差速器gearing n.齿轮传动（装置）offset n.偏置，横距hypoid a.准双曲面的hyperboloid n.双曲面，双曲面体Lesson 22 Shafts, Clutches and Brakes轴、离合器和制动器shaft n.轴clutch n.离合器brake n.制动器pulley n.（皮，胶）带轮flywheel n.飞轮sprocket n.链轮，星轮bending moment 弯曲力矩torsional a.扭转的static a.静（力，态）的axle n.心轴，轮轴spindle n.心轴，主轴deflection n.偏移，弯曲fillet n.圆角，倒角peening n.喷射（加工硬化法）shot peening 喷丸硬化stiff a.刚性的inertia n.惯性，惯量slippage n.滑动actuation n.驱动，开动coefficient n.系数statics n.静力学rim n.边缘，轮缘shoe n.闸瓦，制动片【块】band n.带，条cone n.圆锥miscellaneous a.（混）合的，杂项的assume v.假设，承担statical a.=static,静态的equilibrium n.平衡reaction n.反应，反力overload-release clutch 超载释放（保护）离合器magnetic fluid clutch 磁液离合器shift v.变换，（使）移动lever n.杆，（手）柄jaw n.颚板，夹爪ratchet n.棘轮circumferentiallyad v.周围地，圆周地mate v.配合，啮合，联接synchronous a.同步的linear drive 线性驱动装置clicking n.‘卡塔’声freewheel v.空转coupling n.联轴器sleeve n.套筒flat n.平面（部分）a.平的periphery n.圆周，周边wedge n.楔（形物）v.楔入pawl n.棘爪powder n.粉末mixture n.混合物electromagnetic a.电磁的coil n.线圈excitation n.刺激，激励shearing a.剪切的lockup n.锁住Lesson 41 Definition of Robotics and the Robot Systemmanipulator n.操作器，控制器，机械手peripheral a.周围的，外围的idiot n.白痴integrate v.使成为一体，使结合起来hard automation 刚性自动化a host of 许多Lesson 42 Basics of Computers(I)execute v.执行binary a.二进制的read only memory (ROM) 只读存储器random access memory (RAM)读写存储器，随机存储器erasable a.可擦去的volatile a.可丢失的Lesson 43 Basics of Computers(二)harsh a.恶劣的robust a.稳定的configuration n.结构，组态Morse Code 莫尔斯电码suffice v.足够interference n.干扰fluctuation n.脉动，波动expendable a.可消耗的intermediate a.中间的adaptor n.转换器transformer n.变压器rectifier n.整流器capacitor n.电容器Zener diode 齐纳（稳压）二极管buffer n.缓冲寄存器come across 碰到Baud rate 波特率Lesson 44 Programmable Controllersalbeit conj.虽然light-emitting diodes 发光二极管relay ladder logic 继电器梯形逻辑图archaically a.古体的，旧式的retention n.保留，保持versed a.熟练的，精通的fluidics n.射流sheer a.完全的，绝对的profligate a.浪费的proprietary a.专利的，专有的boolean expression 布尔表达式Lesson 45 CAD/CAMComputed-aided design(CAD) n.计算机辅助设计Computed-aided manufacturing(CAM) n.计算机辅助制造automatic factory n.自动化工厂drafting n.制图Computer-aided engineering n.计算机辅助工程management information systems n.管理信息系统graphics terminal n.图像终端a shared data base n.公用数据库three-dimensional a.三维的keyboard n.键盘lightpen=light pen n.光笔magnify v.放大flip v,n.翻转copy v.拷贝a mirror image 镜像symmetrical a.对称的artwork n.印刷线路原图Geometric modeling n.几何模型制造kinematics n.运动学Lesson 48 Flexible Manufacturing Systemsfexible manufacturing systems(FMS)柔性制造系统flexible manufacturing celles(FMC) 柔性制造单元automated guided vehicles 自动搬运小车conveyor n.传送装置pallet loading and unloading carts 上下料小车part program 零件程序data base 数据库data processing networks 数据处理网络inspection program 检测程序robot program 自动机程序real-time control data 实时控制数据the Control hierarchy 控制层次real-time fault recovery 实时故障恢复unmanned operation 无人化操作chip removel 排屑module n.模块，组件intelligent node智能节点。

机械设计专业英语机械设计专业英语圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧cylindroid helical-coil compression spring 圆柱凸轮cylindrical cam圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator圆锥螺旋扭转弹簧conoid helical-coil compression spring 圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle原动件driving link约束constraint约束条件constraint condition约束反力constraining force跃度jerk跃度曲线jerk diagram运动倒置kinematic inversion运动方案设计kinematic precept design运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion运动综合kinematic synthesis运转不均匀系数coefficient of velocity fluctuation运动粘度kenematic viscosity载荷load载荷—变形曲线load—deformation curve 载荷—变形图load—deformation diagram 窄V 带narrow V belt毡圈密封felt ring seal展成法generating张紧力tension 张紧轮tension pulley振动vibration振动力矩shaking couple振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism正向运动学direct (forward) kinematics正弦机构sine generator, scotch yoke织布机loom正应力、法向应力normal stress制动器brake直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直角三角形right triangle直角坐标操作器Cartesian coordinate manipulator直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm直线运动linear motion直轴straight shaft质量mass质心center of mass执行构件executive link; working link质径积mass-radius product智能化设计intelligent design, ID中间平面mid-plane中心距center distance中心距变动center distance change中心轮central gear中径mean diameter终止啮合点final contact, end of contact周节pitch周期性速度波动periodic speed fluctuation 周转轮系epicyclic gear train肘形机构toggle mechanism轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承高度bearing height轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equivalent axial load轴向当量静载荷static equivalent axial load 轴向基本额定动载荷basic dynamic axial load rating轴向基本额定静载荷basic static axial load rating轴向接触轴承axial contact bearing轴向平面axial plane轴向游隙axial internal clearance轴向载荷axial load轴向载荷系数axial load factor轴向分力axial thrust load主动件driving link主动齿轮driving gear主动带轮driving pulley转动导杆机构whitworth mechanism转动副revolute (turning) pair转速swiveling speed ; rotating speed转动关节revolute joint转轴revolving shaft转子rotor转子平衡balance of rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear 锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear子程序subroutine 子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-locking自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force总效率combined efficiency; overall efficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting组合机构combined mechanism阻抗力resistance最大盈亏功maximum difference work between plus and minus work纵向重合度overlap contact ratio纵坐标ordinate组合机构combined mechanism最少齿数minimum teeth number最小向径minimum radius作用力applied force坐标系coordinate frame行星轮变速装置planetary speed changing devices行星轮系planetary gear train形封闭凸轮机构positive-drive (or form-closed) cam mechanism虚拟现实virtual reality虚拟现实技术virtual reality technology, VRT虚拟现实设计virtual reality design, VRD虚约束redundant (or passive) constraint许用不平衡量allowable amount of unbalance许用压力角allowable pressure angle许用应力allowable stress; permissible stress 悬臂结构cantilever structure悬臂梁cantilever beam循环功率流circulating power load旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selection压力pressure压力中心center of pressure压缩机compressor压应力compressive stress压力角pressure angle牙嵌式联轴器jaw (teeth) positive-contact coupling雅可比矩阵Jacobi matrix摇杆rocker液力传动hydrodynamic drive液力耦合器hydraulic couplers液体弹簧liquid spring液压无级变速hydraulic stepless speed changes液压机构hydraulic mechanism一般化运动链generalized kinematic chain 移动从动件reciprocating follower移动副prismatic pair, sliding pair移动关节prismatic joint移动凸轮wedge cam盈亏功increment or decrement work应力幅stress amplitude应力集中stress concentration应力集中系数factor of stress concentration 应力图stressdiagram应力—应变图stress-strain diagram优化设计optimal design油杯oil bottle油壶oil can油沟密封oily ditch seal有害阻力useless resistance有益阻力useful resistance有效拉力effective tension有效圆周力effective circle force有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion预紧力preload原动机primer mover圆带round belt圆带传动round belt drive圆弧齿厚circular thickness 圆弧圆柱蜗杆hollow flank worm 圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱式凸轮步进运动机构barrel (cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring凸轮cam凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanism凸轮廓线cam profile凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscopeV 带V belt外力external force外圈outer ring外形尺寸boundary dimension万向联轴器Hooks coupling ; universal coupling外齿轮external gear弯曲应力beading stress弯矩bending moment腕部wrist往复移动reciprocating motion往复式密封reciprocating seal网上设计on-net design, OND微动螺旋机构differential screw mechanism 位移displacement 位移曲线displacement diagram位姿pose , position and orientation稳定运转阶段steady motion period稳健设计robust design蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism蜗杆旋向hands of worm蜗轮worm gear涡圈形盘簧power spring无级变速装置stepless speed changes devices无穷大infinite系杆crank arm, planet carrier现场平衡field balancing向心轴承radial bearing向心力centrifugal force相对速度relative velocity相对运动relative motion相对间隙relative gap象限quadrant橡皮泥plasticine细牙螺纹fine threads销pin消耗consumption小齿轮pinion小径minor diameter橡胶弹簧balata spring修正梯形加速度运动规律modified trapezoidal acceleration motion修正正弦加速度运动规律modified sine acceleration motion斜齿圆柱齿轮helical gear斜键、钩头楔键taper key泄漏leakage谐波齿轮harmonic gear谐波传动harmonic driving谐波发生器harmonic generator 斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio 行星齿轮装置planetary transmission行星轮planet gear平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator 燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance 升程rise升距lift螺旋角helix angle螺旋线helix ,helical line绿色设计green design ; design for environment马耳他机构Geneva wheel ; Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress 脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion ;wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise) 啮出engaging-out 啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower 偏置曲柄滑块机构offset slider-crank mechanism拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width 平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket ; sprocket-wheel ; sprocket gear ; chain wheel 联组V 带tight-up V belt联轴器coupling ; shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD 基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle 基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio 急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions 计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS计算力矩factored moment; calculation moment 计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing 角接触推力轴承angular contact thrust bearing角接触向心轴承angular contact radial bearing角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load 径向基本额定动载荷basic dynamic radial load rating径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity 均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment 惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling 滚珠丝杆ball screw 滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design机构mechanism 机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery 机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design 机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD 防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone 分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train 复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism 复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed 变速speed change变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism 并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism 差速器differential 常用机构conventional mechanism; mechanism in common use车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter 齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation ; creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping 带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing 单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear 当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion 等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia 等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine 动态特性dynamic characteristics动态分析设计dynamic analysis design 动压力dynamic reaction动载荷dynamic load。

《机械工程专业英语》测验题(18-22)一、将下列词组译成汉语1.the base circle（基圆）2.the pitch curve（啮合曲线）3.the contact force（接触力）4.the intermittent motion（间歇运动）5.the common normal（公法线）6.the conjugate profiles（共轭齿廓）7.the cycloidal profiles （摆线齿形）8.the involute profiles（渐开线齿形）9.the spur gear（直齿轮）10.the herringbone gears（双螺旋齿轮）11.the face gear（端面齿轮）12.the radial distance（径向距离）13.the addendum circle（齿顶圆）14.The tooth thickness（齿厚）15.the tooth space（齿间隙）16.the cap screws（螺钉）17.the setscrews（固定螺丝钉）18.the engineering graphics（工程力学）19.mechanical design（机械设计）20.the installation techniques（安装技术）21.the bolted joint（螺栓连接）22.the hardened washers（强化垫圈）23.the fatigue resistance（抗疲劳强度）24.the modulus of elasticity（弹性模量）25.the antifriction bearing（减摩轴承）26.the rolling bearing（滚动轴承）27.the rolling contact （滚动接触）28.the sliding contact（滑动触电）29.the corrosion resistance（抗腐蚀性）30.the machining tolerances（加工公差）31.the fatigue loading（疲劳载荷）32.the radial loads（径向负荷）33.the thrust loads逆负荷34.the ball bearing球轴承35.the roller bearing滚子轴承36.the single-row bearings单沟轴承37.the double-row bearing双沟轴承38.the needle bearing滚针轴承39.the bearing life轴承寿命40.The rating life额定寿命41.the axis of rotation旋转轴42.The helix angle螺旋角43.a right-hand helix 右旋44.a left-hand helix左旋45.an involute helicoids螺旋面46.an involute curve渐开线47.the shaft centerlines轴中心线48.worm gear蜗轮49.the hypoid gear准双曲面齿轮50.right angle直角51.worm gearing蜗杆传动52.the lead angle导角53.shaft angle轴线角度54.bending load弯曲载荷55.tension load张力负荷pression load压缩负载57.torsional load扭转负荷58.the bending moment弯矩59.the bending stress弯曲应力60.the shot peening喷丸法61.the actuating force工作力62.the coefficient of friction摩擦系数63.An electromagnetic coil电磁线圈64.the magnetic circuit磁路二、将下列短语译成汉语1.disk or plate translating (two-dimensional or planar)盘形传动凸轮（两维的，即平面的）2.cylindrical (three-dimensional or spatial) cams圆柱形凸轮（三维的，即空间的）机构3. a radial (in-line) translating roller follower一个对心直动滚子从动件4. a constant angular velocity ratio旋转角速度的比例5. a constant torque ratio一个恒转矩比6.Nonlinear angular velocity ratios非线性角速度比率7.the parallel helical gear平行斜齿轮8.the crossed helical gear交叉斜齿轮9.the straight bevel gear直锥齿轮10.the spiral bevel gear弧齿锥齿轮11.the skew bevel gear大角度斜交锥齿轮12.the hexagon head screws六角头螺钉13.the fillister head screws槽头螺钉14.the flat head screws 平头螺钉15.the hexagon socket head screws内六角沉头螺钉。