GKP681 使用手册

NSC681工程调试说明一、前置机与装置的通讯设置1、前置机的通讯设置前置机中的设置共有6个地方，如图（1_1）到图（1_6）。

图（1_1）中的规约通常可选择IEC870_5_101_M 或IEC870_5_104_M。

早期的工程都用IEC870_5_104_M，在CCM的“通讯设置\通讯口设置”选择“定制TCPC网口”。

目前的工程基本使用IEC870_5_101_M，在CCM的“通讯设置\通讯口设置”选择“定制设备网口（UDP）”，如图（1_2）。

在图（1_2）中注意“A/C网周知口（HEX）”中的964换算成10进制2404与nsc-manager中的网卡设置的端口号2404对应。

双网A/C网网址1与nsc-manager中的网卡设置的A网IP地址193.100.100.1对应。

同理设置B/D网。

图（1_1）NSC681在CCM的“通讯设置\通讯设置表”中的设置图（1_2）NSC681在CCM的“通讯设置\设备网口定义”中的设置图（1_3）NSC681在CCM的“规约设置”中的设置图（1_4）NSC681在CCM的“规约设置\端口间发送事件定向”中的设置图（1_5）NSC681在CCM的“规约设置\装置属性设置”中的设置图（1_6）NSC681在CCM的“规约设置\附加设置”中的设置2、用nsc-manager给NSC681进行通讯设置通过nsc-manager设置NSC681时，应首先手动设置（在装置面板上）装置地址，如图（2_1），以便nsc-manager能够找到该装置。

nsc-manager在新建好工程和添加好需要的装置后，选择装置右，键鼠标再选择“初始化装置”出现图（2_2）界面，选择设置网卡，出现图（2_3）界面后选择查找网卡，然后进行如图（2_3）的设置，最后选择确认设置并重启网卡，就可以与前置机通讯了。

这里的设置应注意相应的端口号要与前置机设置一致，建议装置的端口号都选择2404，前置机的端口号都选择20488，20489。

NSC681工程调试说明一、前置机与装置的通讯设置1、前置机的通讯设置前置机中的设置共有6个地方，如图（1_1）到图（1_6）。

图（1_1）中的规约通常可选择IEC870_5_101_M 或IEC870_5_104_M。

早期的工程都用IEC870_5_104_M，在CCM的“通讯设置\通讯口设置”选择“定制TCPC网口”。

目前的工程基本使用IEC870_5_101_M，在CCM的“通讯设置\通讯口设置”选择“定制设备网口（UDP）”，如图（1_2）。

在图（1_2）中注意“A/C网周知口（HEX）”中的964换算成10进制2404与nsc-manager中的网卡设置的端口号2404对应。

双网A/C网网址1与nsc-manager中的网卡设置的A网IP地址193.100.100.1对应。

同理设置B/D网。

图（1_1）NSC681在CCM的“通讯设置\通讯设置表”中的设置图（1_2）NSC681在CCM的“通讯设置\设备网口定义”中的设置图（1_3）NSC681在CCM的“规约设置”中的设置图（1_4）NSC681在CCM的“规约设置\端口间发送事件定向”中的设置图（1_5）NSC681在CCM的“规约设置\装置属性设置”中的设置图（1_6）NSC681在CCM的“规约设置\附加设置”中的设置2、用nsc-manager给NSC681进行通讯设置通过nsc-manager设置NSC681时，应首先手动设置（在装置面板上）装置地址，如图（2_1），以便nsc-manager能够找到该装置。

nsc-manager在新建好工程和添加好需要的装置后，选择装置右，键鼠标再选择“初始化装置”出现图（2_2）界面，选择设置网卡，出现图（2_3）界面后选择查找网卡，然后进行如图（2_3）的设置，最后选择确认设置并重启网卡，就可以与前置机通讯了。

这里的设置应注意相应的端口号要与前置机设置一致，建议装置的端口号都选择2404，前置机的端口号都选择20488，20489。

P/N: 1802006811012 *1802006811012*DA-681C SeriesQuick Installation Guidex86 Rackmount Embedded ComputersVersion 1.2, June 2023Technical Support Contact Information/support2023 Moxa Inc. All rights reserved.OverviewThe DA-681C computer is built around an Intel® Celeron® or Intel® Core™ i3 CPU and comes with dual display ports (2 x HDMI), 5 USB ports, 6 Gigabit LAN ports, 2 3-in-1 RS-232/422/485 serial ports, 10 RS-485 serial ports, 6 digital input ports, and 2 digital output ports. Additionally, one 2.5” HDD/SSD slot and one mSATA slot are included to enable storage expansion for industrial applications that require large storage space for edge data acquisition.With IEC 61850-3 and IEEE 1613 compliance, the DA-681C is sure to deliver stable and reliable system operation for power applications.EN 50121-4 compliance confirms that the DA-681C can deliver stable and reliable system operations in rail wayside applications, such as station SCADA systems, wayside disaster prevention, traction power, and signaling and safety systems, to provide an integrated view of your smart rail setup.Package ChecklistEach basic system model is shipped with the following standard items: •DA-681C rackmount computer•Rack-mounting kit•Quick Installation Guide•Warranty cardHardware InstallationFront ViewRear ViewConnecting the PowerThe DA-681C provides single or dual power inputs using a terminal block, which is located on the rear panel. A grounding connector is also provided for power surge protection.In addition, a power button on the rear panel allows users to power on the computer when it is in the sleep or hibernate mode.Connect the power cord wires to the screws on the power input of the DA-681C and then tighten the screws. The Power LED will light up to indicate that power is being supplied to the DA-681C, after which the BIOS will initialize the flash disk module, causing the Storage LED to blink. It should then take about 30 to 60 seconds for the operating system to complete the boot-up process.For a detailed power connection and surge protection information, refer to the DA-681C Hardware User’s Manual.Front-panel LEDsThere are 42 LED indicators on the front panel, which are described in the following table:LED Color DescriptionPower Green Power is onOff No power inputStorage Yellow/Blinking Data is being written to or read from the storage unitOff Storage unit is idlePower 1 Failure Off The 1st power supply is onRed Error in the 1st power supply Power 2 Failure Off The 2nd power supply is onRed Error in the 2nd power supply Gigabit LAN LEDs 1 to 6 Green 100 Mbps Ethernet modeOrange 1000 Mbps (Gigabit) Ethernet modeSerial Port P1 to P12 (TX/RX) Green Tx: Serial data is being transmitted Yellow Rx: Serial data is being receivedProgrammable LEDs 1 to 8 Green/BlinkingCan be used to indicate statuses orfor debugging, as defined by users.Connecting to DisplaysThe DA-681C comes with 2 HDMI interfaces on the rear panel, allowing users to connect two displaysNOTE For highly reliable video streaming, use premium, certified HDMI cables.Connecting to a Keyboard and MouseConnectors for a keyboard and mouse are located on the rear panel of the computer. Both connectors are PS/2 interfaces; you can directly connect a keyboard and a mouse using these connectors. Serial PortsThe DA-681C comes with 2 software-selectable RS-232/422/485 serial ports (P1 and P2) on the rear panel with DB9 connector. Pin RS-232 RS-422 RS-485 (2-wire) 1 DCD TxDA(-) – 2 RxD TxDB(+) – 3 TxD RxDB(+) DataB(+) 4 DTR RxDA(-) DataA(-) 5 GND GND GND 6 DSR – – 7 RTS – – 8 CTS – –In addition, there are 10 serial ports (P3 to P12) that use terminal blocks. Refer to the following table for the pin assignments: Pin RS-232 RS-422 RS-485 (2-wire)1 TxD TxD(+) –2 RxD TxD(-) –3 RTS RxD(+) Data(+)4 CTS RxD(-) Data(-)5 GNDGNDGNDUSB PortsThe DA-681C comes with 2 USB 2.0 ports on the front panel and 3 USB3.0 ports on the rear panel. The USB ports can be used to connect peripherals, such as flash drives, for expanding the systems storage capacity. Ethernet PortsThe DA-681C has 6 100/1000 Mbps RJ45 Ethernet ports on the rear panel. Refer to the following table for the pin assignments: Pin 100 Mbps1000 Mbps 1 Tx+ TRD(0)+ 2 Tx- TRD(0)- 3 Rx+ TRD(1)+ 4 – TRD(2)+ 5 – TRD(2)- 6 Rx- TRD(1)- 7 – TRD(3)+ 8–TRD(3)-Digital Inputs/Digital OutputsThe DA-681C comes with six digital inputs and two digital outputs in a terminal block. Refer to the following figures for the pin definitions and wiring methods.Relay OutputThe DA-681C provides a relay output located on the rear panel of the computer. Refer to the figure on the right for a detailed pin definition of the relay output connectors.Installing a Storage DriveThe DA-681C is provided with a storage slot located on the front panel for storage expansion.Follow these steps to install a SATA disk.1. Unfasten the screw on the storage slot cover and pull down thecover to access the storage tray.2. Push the clutch on the storage tray to the left to release thestorage tray and pull out the tray.3.Place the SATA disk on the tray.Ensure that the SATA disk aligns with the screws on the storage tray.4.Turn the storage tray and the SATA disk arrangement around toaccess the screws on the rear side of the tray. Fasten the fourscrews to secure the SATA disk to the tray, as indicated in thediagram below.5.Insert the storage tray back into the storage slot.Ensure that the tray is inserted correctly into the rails of thestorage slot and the tray slide smoothly inside the slot.6.Slide the storage slot cover back and fasten the screw to secure it. For details on installing other peripheral devices, refer to the DA-681C Hardware User’s Manual.。

8.1 外接程序.................................................................................. 37 8.1.1 下载考勤数据 37 8.1.2 员工及其指纹管理 38 8.1.3 考勤机管理 43
8.2. 维护/设置................................................................................44 8.2.1 维护/设置 44 8.2.2 部门表 45 8.2.3 员工维护 47 8.2.4 管理员设置 58 8.2.5 时间段维护 62 8.2.6 班次管理 65
上海四景计算机信息科技有限公司
目录
1、使用须知..................................................................................................................... 1.1 用 BIOCLOCK 激活软件.........................................................2
155-4
1、使用须知
上海四景计算机信息科技有限公司
请不要将设备放在强光直照的地方，强光对指纹采集有着明显的影 响，会导致指纹验证无法通过。
夏天尽量不要在室外使用，考勤机工作的温度范围为 0-400C，长期 在室外使用，加上设备本身的发热，容易导致设备工作受到影响，反应 可能会变慢，通过率降低。如果必须在室外使用，建议采用遮阳伞和散 热设备。
155-1
上海四景计算机信息科技有限公司
4.1.2 语言 22 4.1.3 锁驱动 22 4.1.4 高级设置 22 4.2 电源管理.................................................................................. 23 4.3 通讯设置.................................................................................. 24 4.4 记录设置.................................................................................. 25 4.5 门禁功能设置.......................................................................... 26 4.5.1、时间段 的功能定义........................................................... 26 4.5.2、用户门禁设置..................................................................... 27 4.5.3、分组功能定义..................................................................... 28 4.5.4、开锁组合功能定义............................................................. 28 4.5.5、锁驱动时长......................................................................... 29 4.6 自动检测.................................................................................. 29