SMC数显说明书

拆卸时应先将电动装置吊装可靠再松开紧固螺栓，而后将其自阀门上取下。
5．4 SMC/HBC、SMC/JA部分回转产品的安装与拆卸方法是：
先将花键接头装到阀杆上，使电动装置二级减速机构的驱动轴位置与阀门所处位置相同。
（此时阀门在某一终端位置最理想）起吊电动装置，使其驱动轴与阀杆上的花键接头对准，同时应对准阀门与电动装置的连接螺孔。使驱动轴与花键接头配合装入，而后用螺栓将阀门与电动装置紧固可靠。
a、型号：该产品型号。
b、最大控制转矩：该产品出厂前调定的最大转矩值（N.m）。
c、输出转速：该产品在单位时间内输出轴的转圈数（r/min）。
d、最大转圈数：该产品位置指示机构指针从0～100％走满刻度情况下输出轴总的转圈数。
e、编号：该产品总序号或本年度产品的序号。
f、合同号：该产品年度订货合同号。根据它可查出产品出厂前的全部情况，便于售后服务。
与G·L·SW的触点信号不同，MDPI的阀位反馈信号是连续的。
（图19）所示为MDPI位置指示机构的结构。从图中可见其传动部分是若干对小模数配换齿轮，该机构对任何口径的阀门均能保证其指针做满刻度指示。
▼关于电动装置的控制器
对于一般控制原理，控制器是与电动装置分离的电气控制部件，它通常设置在控制室内为单独订货产品。
5．7电动装置的工作位置一般无原则要求。但推荐电动机轴线为水平状态，G·L·SW箱罩处于水平或垂直向上、向下状态，以利于产品的润滑、维修及阀位观测。
6．润滑
6．1产品出厂前已注入专用润滑脂，使用中每年应至少检查润滑情况一次，如无异常可继续使用。
6．2电动机轴承的润滑脂一般不必更换或添加。
6．3产品维修后更换润滑脂时应注意其抗氧化性、耐水性、耐热性、防锈性、机械稳定性等，并应注意其抗挤压性，以保证产品的润滑性能和较高的传动效率。

雷赛SMC608说明书
雷赛SMC608说明书步进电机驱动器上拨码开关有D1、D2、D4-
D6，它们分别的设置方法如下：
1、D1设置的是驱动器的发出脉冲的方式。

如果不是步进电机驱动器自身发出脉冲控制电机的话，D1设置成OFF。

如果是步进电机驱动器自身发出脉冲，那么将D1设置成ON即可。

2、D2设置的也是驱动器的发出脉冲的方式，但是条件是必须在D1设置为OFF时，D2设置才会生效。

2、D4-D6设置的是步进电机工作细分数，即步进电机旋转一圈需要的脉冲数。

细分越大精度也就越高，但是也越容易产生误差。

(Cat 150-SM6)SMC-50 Parameter Configuration Option ModuleInstallation Instructions34IND. CONT. EQ.WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in a suitable enclosure. Keep free from contaminants.DIP Switch and Rotary Switch LocationsSwitchDiagnostic LEDs 11) For details regarding the operation and meaning of the Diagnostic LEDs refer to the SMC-50 User Manual 150-UM011_-EN-P.150-SM6 Switch Position Identification:The following defines the functions of the 5 Rotary Switches:S1 = Initial Torque Configuration:S2 = Current Limit Configuration:S3 = Ramp Time Configuration- Starting:Rotary Switch S1 Position Setting Resulting Initial Torque Value (in % Motor Torque)0 10 1 16 2 22 3 28 4 34 5 40 6 46 7 52 8 58 9 64 A 70 (Default) B 76 C 82 D 88 E 94F 100Rotary Switch S2 Position SettingResulting Current Limit Value (in % Motor FLC )0 200 1 220 2 240 3 260 4 280 5 300 6 320 7 340 8 360 (Default) 9 380 A 400 B 420 C 440 D 460 E 480 F 500Rotary Switch S3 Position Setting Starting Ramp Time (in Seconds)0 0.11 2 2 4 3 6 4 8 5 10 (Default) 6 12 7 14 8 16 9 18 A 20 B 22 C 24 D 26 E 28 30F 1) When the “Braking” STOP MODE is selected (Device Configuration Bank Switch #3 and #4) the controller multiplies the selected “Stop Time” by 10. Refer to Device Configuration Switch Bank.S5 = Motor FLC (Full Load Current) Configuration:Rotary Switch S 5 Position Setting % of Controller’s Max FLC (1) (2)0 40 (Default) 1 44 2 48 3 52 4 56 5 60 6 64 7 68 8 72 9 76 A 80 B 84 C 88 D 92 E 96F 100(1) Since a set of switches do not provide the resolution to enter all possible Motor FLC combinations like a keypad, Switch S5 allows you to configure the Motor’s FLC in the SMC50 by using a percent (%) of the controllers raed (e.g 90A, 110A, 140A, 180A, etc) FLC.-Example: For a 60A motor and a 90A controller, the % of Controller’s max FLC for 60A would be 64% of 90A (57.6A) or switch position 6. (2) To determine the S5 switch setting for an inside the delta motor configuration use the following 2 equations:Motor NameplateFLC1.73XStep 1:Step 2:XSMC - 50Controller RatingS5 Switch Setting100A 1.7357.8AStep 1: Step 2:57.8A 90AExample:64%S5 = Position 6X100X100NOTE:Switch Number #1 #2 #3 #4 #5 #6 #7 #8 Start M odeLinear Speed Accel (Default)0 0 Current Limit 0 1 Soft Start 1 0 Pump Start1 1 Stop Mode (1)(2)Linear Speed Decel (Default)0 0 Soft Stop 0 1 Braking 1 0 Pump Stop1 1 Energy SaverEnable1 Disable (Default)0 Braking Current50% 0 0 0 100% 0 0 1 150%0 1 0 200%(Default)0 1 1 250% 1 0 0 300% 1 0 1 1) If the calculated value doesn’t match a switch position use the previous (lower percent) switch setting2) The inside the delta motor configuration can be selected using Parameter 44 (Motor Connection) or automatically during a controller Tuning process.The following defines the functions of the 3 banks of On/Off 8-switch DIP switches. Each of the 3 banks is defined by a high level functional name (e.g. Device, I/O and Protection) with each switch having a unique function. Device Configuration Bank (0=OPEN):I/O Configuration (1) Bank (0=OPEN):Switch Number #1 #2 #3 #4 #5 #6 #7 #8 Aux #1 ConfigurationNormal(default) 0 0 Up-to-Speed 0 1Fault 1 0 Alarm 1 1Aux #2 ConfigurationNormal 0 0Up-to-Speed(default) 0 1Fault 1 0 Alarm 1 1Input #1Start/Coast(default) 0 Start/Stop Option 1Input #2Stop Option(default) 0 0Clear fault 0 1 Slow Speed 1 0Fault 1 1(1) The I/O configuration ability of the 150 - SM6 is limited to the Control Module’s standard I/O.Protection Configuration Bank (0=OPEN): Switch Number #1 #2#3 #4 #5 #6 #7 #8Preset Protection LevelDisabled 0 Enable(Default) 1Stall FaultEnable(Default) 1Disable 0Phase Reversal FaultEnable 1Disable(Default) 0OL RestartEnable 1Disable(Default) 0OL EnableEnable(Default) 1Disable 0Trip Class10(Default) 0 015 0 1 20 1 0 30 1 1NOTE:For details concerning the operation of the Parameters controlled by the 150-SM6 Switch settings refer to the SMC-50 User Manual (Publication 150-UM011_-EN-P) available from , Publications Library.(1) When the "Stop Mode" is configured as a) "Linear Speed Decel", b) "Soft Stop" or c) "Pump Stop" and the "Stop Time" (Rotary Switch S4) is set to 0 a “Coast” to stop will result. A non-zero “Stop Time” value for the 3 previously listed “Stop Modes” defines the time to stop period based on that specific configuration. (2) If the "Stop Mode" is configured as "Braking" then the "Stop Time" setting (Rotary Switch S4) is used to select either the "Automatic Zero Speed Detection" method ("Stop Time" set to 0) or the "Timed Brake" method ("Stop Time" not set to 0). NOTE:a) With the “Automatic Zero Speed Detection” method, the controller applies the user selected “Braking Current” defined by the Device Configuration Switch Bank, Switch #6, #7 & #8, senses a motor “Zero Speed” condition and automatically stops the braking process.b) With the "Timed Brake" method the user selected “Braking Current” is applied for the user configured “Stop Time” regardless of the motor speed (i.e. “Automatic Zero Speed Detection” disabled). The “Timed Brake” method can be used in applications where detecting zero speed is ineffective or when braking the motor to a complete stop results in random overload trips. With this method, braking is applied for a fixed time equal to the “Stop Time” setting (Rotary Switch S4) times 10. An ideal ‘Stop Time” setting can be accomplished by trial and error, but should always allow for some coast time. Setting the “Stop Time” for to long can result in braking current to be applied to a stopped motor and will likely result in overload trips.。

ZSM-SMY10EN Page 1 of 1Instruction ManualVacuum SwitchSeries ZSM1 – 115/121The intended use of vacuum switch is to control the source pressure of the vacuum line and the pressure of each line by electric signals.1 Safety InstructionsThese safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.” They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC) *1), and other safety regulations. *1)ISO 4414: Pneumatic fluid power - General rules relating to systems. ISO 4413: Hydraulic fluid power - General rules relating to systems.IEC 60204-1: Safety of machinery - Electrical equipment of machines. (Part 1: General requirements)ISO 10218-1: Manipulating industrial robots -Safety. etc.• Refer to product catalogue, Operation Manual and Handling Precautions for SMC Products for additional information. • Keep this manual in a safe place for future reference.CautionCaution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.WarningWarning indicates a hazard with a medium level of riskwhich, if not avoided, could result in death or serious injury.DangerDanger indicates a hazard with a high level of risk which, ifnot avoided, will result in death or serious injury.Warning• Always ensure compliance with relevant safety laws and standards.• All work must be carried out in a safe manner by a qualified person in compliance with applicable national regulations.2 Specifications2.1 Specifications ModelZSM1-115 ZSM1-121 Switch specificationsSolid StateContact (reed switch)FluidAir/Inert Gas Max. operating pressure 0.5 MPa Regulating pressure range -27 to -80 kPaHysteresis Max. 15 kPa Max. 20 kPaRepeatability±10% or less Ambient and fluid temperature -5 to 60°C (no freezing)Supply Voltage 4.5 to 28 VDC 100 VAC/DC(or less)Indicator Light ON: When output is ON Lead Wires 3 2Port size R1/8 Weight 65g2Specifications- continued2.2 Electrical Specifications ZSM1-115Supply Voltage4.5 to 28VDC Output (open collector) 28 V: Max. 40 mA Current consumption 10 mA or less (24 VDC)ZSM1-121Supply Voltage100 VAC/DCMaximum operating current24 V or less: Max. 50 mA48 V: Max. 40 mA 100 V: Max. 20 mA Max. contact capacity AC 2 VA, DC 2 WWarningSpecial products might have specifications different from those shown in this section. Contact SMC for specific drawings.3 Installation3.1 InstallationWarning• Do not install the product unless the safety instructions have been read and understood.ZSM1-115ZSM1-1213.2 EnvironmentWarning• Do not use in an environment where corrosive gases, chemicals, salt water or steam are present.• Do not use in an explosive atmosphere.• Do not use within proximity of a magnetic field as this will cause disruption to switch and result in malfunction.• Do not expose to direct sunlight. Use a suitable protective cover.• Do not install in a location subject to vibration or impact in excess of the product’s specifications .• Do not mount in a location exposed to radiant heat that would result in temperatures in excess of the product’s specifications. 3.3 LubricationCaution• SMC products have been lubricated for life at manufacture, and do not require lubrication in service.• If a lubricant is used in the system, refer to catalogue for details. 3.4 PipingCaution• Before connecting piping make sure to clean up chips, cutting oil, dust etc.• When installing piping or fittings, ensure sealant material does not enter inside the port. When using seal tape, leave 1 thread exposed on the end of the pipe/fitting.• Tighten to the specified tightening torque.Specified tightening torque R1/8 3~5 N •m3 Installation- continued• When piping switch by hand, hold the body. Do not subject the electrical wire to excessive force.• Do not drop or apply excessive force. It may cause damage and result in product malfunction• Tighten switch by applying wrench on the fitting part. Do not apply wrench on main body as it may cause damage.• Mounting is possible in either horizontal or vertical orientation.4 Settings4.1 WiringCaution• Do not apply excessive pulling force on lead wire. It may cause damage and result in product malfunction.ZSM1-115ZSM1-121• Switches may be connected in series, voltage drop will be increased by LED’s internal resistance (2 V drop per each switch). Use switches within the specified range of operating voltage.• Switches do not have built-in contact protection circuits. Use switches with contact protection box (part number CD-P11) with inductive loads or 5 m (or more) lead wire length.Internal circuit contact protection box4.2 Setting vacuum pressure4 Settings- continued• Turn the screw clockwise to set the high vacuum.• No. of turns for pressure setting adjustment is between 0 and 18 turns.5 Outline Dimensions (mm)Refer to catalogue for outline dimensions.6 How to OrderRefer to catalogue for ‘How to Order’.7 MaintenanceGeneral MaintenanceCaution• Not following proper maintenance procedures could cause the product to malfunction and lead to equipment damage.• If handled improperly, compressed air can be dangerous.• Maintenance of pneumatic systems should be performed only by qualified personnel.• Before performing maintenance, turn off the power supply and be sure to cut off the supply pressure. Confirm air is released to atmosphere.• After installation and maintenance, apply operating pressure and power to the equipment and perform appropriate functional and leakage tests to make sure the equipment is installed correctly.• If any electrical connections are disturbed during maintenance, ensure they are reconnected correctly, and safety checks are carried out as required to ensure continued compliance with applicable national regulations.• Do not make any modification to the product.• Do not disassemble the product, unless required by installation or maintenance instructions.8 Limitations of UseLimited warranty and Disclaimer/Compliance Requirements Refer to Handling Precautions for SMC Products.9 Product disposalThis product should not be disposed of as municipal waste. Check your local regulations and guidelines to dispose this product correctly, in order to reduce the impact on human health and the environment.10 ContactsRefer to or www.smc.eu for contacts.URL : http// (Global) http// www.smc.eu (Europe) SMC Corporation, Akihabara UDX15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101 0021Specifications are subject to change without prior notice from the manufacturer. © 2020 SMC Corporation All Rights Reserved. Template DKP50047-F-085JORIGINAL INSTRUCTIONSRefer to Declaration of Conformity for relevant Directives。