报警说明(斗山机床维修)
- 格式：xls
- 大小：86.00 KB
- 文档页数：9
号码英文注释中文注释2001OP EMERGENCY PB OR LS OFF急停开关被按下或轴向限位开关被碰到2002MAIN SPINDLE SERVO ALM主轴伺服报警2003CIRCUIT PROTECT TRIP电路保护故障2004HYD。PUMP MOTOR OVERLOAD液压马达过载2005HYD。PRESSURE DOWN ALARM液压压力低报警2006HYD。PUMP MOTOR NOT RUN液压马达没有运转2007SPINDLE STOP SIGNAL ALARM主轴停止信号报警2008GEAR SHIFT CHECK SW。ALARM换挡检测开关报警2009MAGAZINE EMG。STATUS刀库急停2011MAIN POWER PHASE&ATC SWITCH ER总电相序或ATC开关错误2015SPINDLE TOOL UNCLAMP ALARM主轴松刀报警2017SPINDLE HEAD OIL OVERFLOW 主轴冷却油过溢2020CLT.&LUB&ATC.MOTOR OVERLOAD冷却，润滑，或ATC马达过载2021AIR PRESSURE DOWN ALARM气压低报警2022SPINDLE ORINETATION OVERTIME主轴定位超时2023M06 COMMAND OVERTIME ALARMM06命令超时报警2024T.CODE COMMAND ERRORT码命令错误2025TOOL NO.SELECT KEEP/R NOT SET刀具号选择保持开关没有设定2026GEAR SHIFT OVERTIME ALARM换挡超时报警2027SPDL SPEED ARRIVAL ALARM主轴速度到达报警2028SPINDLE ROTATION MALFUNCTION主轴旋转故障2029APC DOOR OPENAPC门被打开2030TOOL CHANGE MOTOR BRAKE RLS换刀马达刹车释放2031ATC MAINTENANCE STATUS INTATC维护状态2032EXTERNAL FEED HOLD (OP PB SW)外部速率保持2033SPINDLE HEAD OIL PUMPING ALARM主轴冷却油泵报警2034CLNT W/TANK OR LEVEL SW ALARM冷却液水位低报警2035TSC W/TANK MOTOR OVERLOADTSC冷却马达过载2036TOOL SEARCH ILLEGAL ALARM刀具搜索违法报警2037M06 COMMAND ILLEGAL ALARM M06命令违法报警2039MAG.MOVING ILLEGAL POS.ALARM刀库移动错误位置报警20434-AXIS PRESSURE DOWN CHECK AL第四轴压力低检测报警2045FIXTURE CLAMP/UNCLAMP ALARM夹具夹紧放松报警2047ATC DOOR OPEN ATC门被打开2048OPERATORS SIDE DOOR OPEN操作门被打开2050LUB.LEVEL LOW OR PRESSURE DOWN润滑油位低或压力低2051OIL COOLING UNIT ALARM油温冷却器报警2052COOLANT FILTER CHANGE ALARM冷却过滤器转换报警2053COOLANT PRESSURE DOWN ALARM 冷却液压力低报警2054TOOL LIFE MANAGE MENT END ALARM刀具寿命结束报警2058PARTS COUNT END ALARM工件计数结束报警2060SPINDLE TOOL CL/UNCL ALARM主轴刀具夹紧/放松报警2061TMG STOPPER IN/OUT ALARM刀库停止器进出报警2062ATC CHANGER POS. ALARMATC 换刀位置报警2063SAFETY SWITCH LOCKING ALARM 安全开关锁定报警立 加 报 警 说 明号码英文注释中文注释2064WAIT.POT(MAG) SPD/MAG.SIDE AL刀库等待刀杯到主轴侧/刀库侧报警2065CHANGER ARM POS.CHECK ALARM换刀臂位置检查报警2066MUST BE COMMAND NEXT TOOL No.必须指定下一个刀号2068ATC DOOR OPEN /CLOSE ALARMATC门开/关报警2074ATC OVERTIME ALARMATC超时报警2075ATC MAGAZINE ROT.OVERTIME ALARMATC 旋转超时报警20774TH-AXIS CL/UNCL SW.ALARM第四轴夹紧放松开关报警2079TOOL MAG.SYNCHRO MALFUNCTION刀库同步故障2080ATC INTERLOCK ALARM ATC 互锁报警2081ATCMAGAZINE GUARD DOOR OPENATC 刀库门开报警2082ATC MAG.POT TOOL OUT SW.ALARM刀库刀杯出来报警2083ATC MAINTENANCE STATUSATC维护状态2084APC SET-UP STATION DOOR OPENAPC安装站门开2085THERMAL COMPENSATION ERROR热补偿错误2087GEAR SHIFT LOST档位丢失2088TOOL BREAKAGE 刀具破损2089TOOL WEAR DETECT 刀具磨损检测2090PALLET UNCLAMP STATUS工作台放松中2094CHIP OR SCREW CONVEYOR ALARM排屑机报警2099DRUM FILTER CHIP CLT.LOW LEVEL鼓式过滤器液面低2101MUST BE RETUREND TO REF.POINT必须返回原点2102CYCLE START IN FIXTURE UNCLAMP夹具放松时的循环启动2103MUST BE ATC 1 CYCLE ATC必须循环一次 K12.4=12104SPINDLE TOOL No .ZERO主轴刀号为02105ATC OP MAUAL MODE ATC手动模式2106APC OP MAUAL MODE APC手动模式2107FEEDRATE OVERRIDE 0%进给倍率选择开关为02108AUTO POWER OFF READY自动电源关准备中2109MACHINE LOCK ON STATUS机床锁定中2110AUXILIARY FUNC.M,S,T,LOCK ON辅助机能，即M，S，T锁定中2111APC SET-UP SW.UNPUSHAPC设定按扭没有按下2112MAN AXIS MOVING INTERLOCK手动轴移动互锁2113SPDL STOP IN CUTTING MODE CMD切削模式主轴停2114RST COMMAND ALARM ON STL复位命令报警
序号英文注释中文注释
2003The control circuit protectors are tipped out or fuse blown空气开关跳脱或保险丝熔断2004The hydraulic motor is overloaded液压马达过载The hydraulic pressure becomes below the setvalue..油压压力在设定值以下Trouble of hydraulic pressure s/w油压压力开关故障
2008Fault of gear shift confirmation switch.换挡开关出错
2010Machine is in Not Ready status.机床准备不足状态The X-axis torque limiter s/w is tripped out.X轴扭力开关被绊住Trouble of x-axis torque limiter switchX轴扭力开关出错The Z-axis torque limiter s/w is tripped out.Z轴扭力开关被绊住Trouble of z-axis torque limiter switchZ轴扭力开关出错The B-axis torque limiter s/w is tripped out.B轴扭力开关被绊住Trouble of B-axis torque limiter switchB轴扭力开关出错The hydraulic oil of drain oil reservoir is overflowed.液压蓄油池过溢报警Trouble of float switch in the oil reservoir液压蓄油池过溢出错
2021The Torque limit SKIP command is used incorrectly.使用扭力限制跳过命令出错2022The spindle orientation command (m19) is not accepted.主轴定位命令没有执行2023The tool change command is not accepted.换刀命令没有执行2024Incorrect tool No.is commanded.错误的刀浩命令
2027The spindle speed arrival signal is not detected.主轴速度抵达信号出错2028Spindle rotation command(M03/M04)is not accepted.主轴旋转命令没有执行The splash guard door is opened 防溅门开Trouble of door interlock limit switch 门互锁限制开关故障]
2031The reference point return is not completed.原点复归没有完成2032In auto mode ,FEED HOLD status 自动模式下进给保持Air pressure becomes below the set value气压在设定值以下Trouble of Air pressure limit switch 气压限位开关故障
Trouble of chucking confirmation limit switch 卡盘夹紧近接确认开关故障卡盘夹紧近接确认开关位置错误Proximity switch to detect the chuckingconfirmation is at a wrong position.2033
203420292026
2030在不正确的模式执行机床锁定指令2017
Keep relay setting to define the machine model isnot selected2019
The AC motor is overloaded.(coolant or lubricationpump motor)2020
