塑胶模具类英语单词塑胶模具是一种用于压塑、挤塑、注射、吹塑和低发泡成型的组合式模具的简称。
下面是我整理的塑胶模具类英语单词，欢迎阅读学习。
1) Designer - 〔制定〕师。
2) Assembly drawing - 模具组装图。
3) Mold layout - 模具结构图。
4) 2D product drawing - 2D产品图。
5) 3D product data - 3D产品数据。
6) Part drawing - 散件图。
7) Insert molding - 镶件模。
8) 2 color mold / Double injection tool - 双色模。
9) Hydraulic system - 油/水压系统。
10) Parting line - 分模线。
11) Air venting - 排气槽。
12) Cooling system - 冷却系统。
13) Screw - 镙丝。
14) Hot runner system - 热流道。
15) Valve gate - 伐针入水口。
16) Fan gate - 扇型入水口。
17) Pin point gate - 针点进胶。
18) Moon gate / Banana gate - 香蕉,象牙入水口。
19) Submarine gate - 潜水口。
20) Injection machine tonnage - 注塑机吨数。
2关于塑胶模具类英语词汇21) Number of cavity - 穴数。
22) Steel - 钢材。
23) Copper - 铜。
24) Tungsten copper - 钨铜。
25) Beryllium copper - 铍铜。
26) Hardening - 加硬/淬火。
27) Tempering - 回火。
28) Chroming - 电镀。
29) Painting - 喷漆。
30) Resin - 胶材。
.'专用词汇表一、生产流程1.插机(刮蓝胶)component- inserting2.装配assembly3.修理repair4.包装packaging5.成品仓finished goods warehouse6.返工rework7.啤胶件8.组件成型component moulding9.IC烧录IC program10.插件insection11.注塑plastic injection12.发料material delivery13.插机14.零件加工component-processing15.炉前外观检查visual inspection beforewave soldering16.电源板波峰焊power board wave soldering17.执锡18.零件后焊hand soldering19.零件焊接&打黄胶20.低电压测试low voltage test21.半成品外观检查Semi-finished goods visualinspection22.过水洗机23.打热熔胶dotting hot glue24.装卡板25.pallet栈板26.IC烧录IC program27.SMT(刮锡膏)28.喷油spray conformal coating29.焗干防水油30.welding 焊接31.breathing 排气32.feed 供料33.Tiana天那水34.to load material上料to unload material卸料to return material/stock to退料.'35.to fix a die装模to take apart a die拆模36.cold forging 冷锻press forging 冲锻37.to impose lines压线to compress, compressing压缩38.焗炉温度39.开槽groove40.shearing剪断41.接线端子terminal42.to stake, staking, reviting铆合43.fuse together熔合44.electrical sparkle电火花45.fit together组装在一起46.fasten锁紧(螺丝)47.rotating speed, revolution转速48.argon welding氩焊49.to take apart a die卸下模具50.to load a die装上模具51.to tight a bolt拧紧螺栓to looser a bolt拧松螺栓pound die复合模53.punched hole冲孔54.buffing 抛光55.chamfering machine 倒角机56.panel board镶块57.to cutedges=side cut=side scrap切边58.to pull, to stretch拉伸59.Line streching, line pulling线拉伸60.engraving, to engrave刻印61.degrease脱脂62.rinse水洗63.pierce die冲孔模64.forming die成型模65.progressive die连续模66.gang dies复合模67.shearing die剪边模68.riveting die铆合模69.pierce冲孔70.forming成型(抽凸,冲凸).'71.draw hole抽孔72.吹热缩管73.胶芯plastic core二、夹具设备、工具74.烙铁iron75.排氣扇A exhaust fan76.稀釋劑a tinner77.水洗锡线78.pallet栈板79.gunk 料斗80.caliper gauge 卡规81.Screw driver起子82.barcode scanner条码扫描器83.热风枪hot air reflowing gun84.taker取料机85.roller 滚筒runner 流道86.plastic basket胶筐87.isolating plate baffle plate; barricade隔板88.steel plate钢板89.roll material卷料90.conveyer belt输送带91.transmission rack输送架92.钢网stencil93.油墨printing ink94.插机并过炉95.高压测试hi-pot test96.铣刀milling cutter97.发热管heater98.烙铁咀iron tip99.静电手套ESD gloves 100.风枪air gun101.punch冲头102.g roove punch压线冲子103.a ir vent排气道104.w elding line熔合痕105.C ONN Connector 连接器106.C AV Cavity 模穴107.A SS'Y Assembly 装配,组装108.继电器relay109.磨床切割片110.延时器delay timer.'111.热电偶Heat control sensor 、thermocouple 112.电磁阀Solenoid113.温控器Temperature control114.烙铁发热芯heater core for iron115.剪钳wire cutter116.电批开关Electric screw driver switch 117.电批Electric screw driver118.电批齿轮Electric screw driver gear 119.火牛transformer120.碳刷Carbon brush121.吸锡泵suck solder pump122.尖嘴钳micro long nose pliers123.热熔胶枪glue gun124.热风筒heating gun125.f use machine热熔机126.烙铁座iron seat127.静电带wrist strap128.波峰锡炉wave soldering oven129.水循环系统water-recycling system 130.水洗机131.防水油conformal coating132.自动成型机auto-moulding machine 133.电晶体自动成型机134.螺丝泵screw pump135.恒温运风焗炉136.手浸锡炉137.剪脚机138.超声波蒸水机139.表面组件拾放机140.高周波塑料熔接机141.半自动锡浆印刷机142.剪线机143.超声波啤机ultrasonic welding machine 144.自动绕线机145.超声波清洗机ultrasonic cleaning machine 146.振动试验台vibration test platform 147.计算机剥线机electronic wire-peeling machine148.贴片机SMT equipment149.供料器feeder.'150.红外焗炉151.封黑胶预热炉152.回焊炉温度曲线测试仪153.焗炉154.进料器车155.锡浆搅拌机156.无铅波峰焊机157.开线机158.封口机159.胶纸机160.移载装置161.送板机162.周转车163.发电机electric generator 164.注塑机plastic injection machine 165.碎料机smashing machine 166.干燥机drier167.自动吸料机auto-sucking machine 168.锯床169.车床lathe 170.钻床171.punching machine 冲床172.干燥机drier173.冷水机cooler174.数控精密火花机175.移印机printer176.手动吊机177.热油机oil-heating machine178.叉车forklift179.磨床grinder180.铣床miller181.sheet metal parts 冲件182.punching machine 冲床183.过滤器filter184.碎料干燥机185.抽湿机186.热风回焊炉hot air reflow soldering oven 187.注塑机plastic injeciton machine 188.润滑油grease189.汽缸Rmulti cylinder.'190.螺丝screw191.弹簧spring192.蜂鸣器buzzle193.刮刀squeegee194.真空杯vacuum cup195.真空咀vacuum tip196.喷嘴Nozzle197.支架bracket198.六角板手hex.wrench199.过滤器Filter200.密封圈airproof ring 201.套筒/活塞piston202.顶针thimble203.传输皮带belt/conveyor 204.真空棉 pad vacuum 205.消音器muffler206.滑轮Pulley,idler tension,asy pre-tension207.夹片Replacement Fine Foil 208.线夹wire clamp 209.扎线tie wrap210.通风孔blowhole211.自功螺丝self-tapping screw212.保险丝Fuse213.高度规High dividers214.螺线管solenoid215.送/扯线螺线管Spring solenoid assembly 216.焊咀gaiser217.电源线Power cord218.测试针test probe219.变压器transformer220.弹性定位柱spring fixation pole 221.铝皮sheet aluminum222.网络线communicate wire223.电磁阀Solenoid AIRTAC224.精调电阻Precision adjustable resisto 225.脚踏开关foot switch226.开关电源switching power227.散热片Thermal Conductive Pad 228.旋转开关Rotary switch.'229.接线柱Pole Wiring230.音频插头Audio plug231.按键开关keyswitch232.保险丝座Fuse jack233.定位柱fixation pole234.ICT压棒ICT-PRESSING STICK 235.除泡剂Defoamer236.继电器Relay237.电线束electrical wiring harness 238.锡箔纸Solder foil papper239.针筒needle canister240.光电开关Photoelectricity switch 241.电批Electric screw driver242.烙铁soldering iron243.黄油（润滑油）butter (lubricant) 244.气管wind pipe245.刀片blade246.bolt螺栓247.trailer=long vehicle拖板车248.stopper阻挡器249.flow board流水板250.vaccum cleaner吸尘器251.q uenching淬火252.tempering回火253.annealing退火254.volatile挥发性255.风批Pneumatic driver256.电批Electric screw driver三、质量管理QC : quality control 质量管理257.IQC : incoming quality control 进料质量管理258..OQC : output quality control 出货质量管理259.PQC : process quality control 制程质量管理也称260.IPQC: in process quality control. 261.A QL : acceptable quality level 允收标准262.CQA: customer quality assurance 客户质量保证263.PPM Parts Per Million 百万分之一.'264.MA : major defect 主要缺点MI : minor defect 次要缺点265.CR :critical defect 关键缺点266.SMT : surface mounting technology 表面粘贴技术267.SMD : surface mounting device 贴片机268.SMC : surface mounting component 表面粘贴组件269.ECN : engineering change notice 工程变更通知270.DCN : design change notice 设计变更通知271.B OM : bill of material 物料清单-STD-105E : 美国陆军标准,也称单次抽样计划.273.NG :Not Good 不行,不合格274.ESD Electry-static Discharge 静电排放275.5S 希腊语整理,整顿,清扫,清洁,教养276.Polarity : 电性/极性Icicles : 锡尖277.Non-wetting : 空焊278.burr 毛刺，批锋279.locking knot 死结280.torsion 扭曲281.w arpage 翘曲282.waviness 波痕283.flying 飞件284.blister 起泡285.Short circuit : 短路286.冷焊cold soldering287.non-welding288.假焊289.包焊290.焊点291.l ifted solder 浮焊292.pseudo soldering 虚焊293.open soldering脱焊294.Splay mark 水纹295.icicle/solder projection拉尖.'296.Flow mark 流纹297.White patches on surface 表面白斑298.Sink marks 缩影299.Mold release 脱模300.焊盘soldering tray301.M issing component : 缺件302.Wrong component : 错件303.Excess component : 多件304.Insufficient solder : 锡少305.Excessive solder : 锡多306.Solder residue : 锡渣307.Solder ball : 锡球308.Tombstone : 墓碑309.breaking.(be)broken,(be)cracked 断裂310.S ideward : 侧立311.cosmetic defect外观不良312.mixed color杂色313.die repair模修314.rust生锈315.grease/oil stains油污316.delamination起鳞317.gouge沟槽;凿槽318.inclusion杂质319.poor staking铆合不良320.oxidation 氧化321.abrasion磨损322.reverse angle = chamfer倒角323.failure, trouble故障324.dents压痕325.defective upsiding down抽芽不良326.defective to staking铆合不良327.embedded lump镶块328.feeding is not in place送料不到位329.stamping-missing漏冲330.excessive gap间隙过大331.b urr(金属)flash(塑件)毛边dewed=moldy=mouldy发霉333.slipped screw head & slippery screw head螺丝滑头334.slipped screwhead/shippery screw thread滑手.'335.speckle斑点336.dimension/size is a little bigger尺寸偏大(小)337.not up to standard不合规格out of specification338.shrinking/shrinkage缩水339.mixed color杂色340.discoloration异色341.a geing 老化342.hardening 硬化343.overheating 过热344.rust prevention 防蚀345.tempering 回火346.water spots水渍347.exposed metal/bare metal金属裸露ck of painting烤漆不到位ponent damage : 零件破损350.Gold finger : 金手指351.S OP : standard operation process 标准操作流程352.SIP : standard inspection process 标准检验流程353.Simple random sampling : 简单随机抽样354.SPC : Statistical process control 355.SQE : Supplier quality engineering 356.Sampling sample :抽样计划357.fixture : 治具358.Gauge 量规359.QTS: Quality tracking system 质量追查系统360.Spare parts :备用品361.I nventory report for : 库存表362.Manpower/Tact estimation 工时预算363.Calibration : 校验364.Corrugated pad : 波纹垫365.Conductive bag : 保护袋366.Fixture : 制具367.Probe : 探针368.Lint-free gloves : 静电手套369.Wrist wrap : 静电手环370.plug hole孔塞371.W rong direction 极性反ponent damage or broken 零件破损373.Unmeleted solder熔锡不良374.flux residue松香残渣375.wrong label or upside down label贴反376.mixed parts机种混装377.poor solder mask绿漆不良378.氧化Oxidization379.刮花Scratch380.脏污Contamination381.变形Deformation382.stand off height浮高383.IC reverse IC反向384.supervisor课长385.Forman组长386.R.T.Y: Rolled throughout yield直通率387.PPM: Parts per million 不良率388.DPU: Defects per unit 单位不良率389.Resistor: 电阻390.Capacitor:电容391.R esistor array : 排阻392.Capacitor array: 排容393.DIODE: 二极管394.triode: 三极管395.Crystal:震荡器396.Fuse:保险丝397.Bead: 电感inductor398.Connector:连结器399.Metal Shearing:裁剪400.ERP: Enterprise Resource Planning 企业资源规划401.P rocessed material: 流程性材料402.Corrective action:纠正措施403.Preventive action:预防措施404.PDCA:Plan/Do/Check/Action计划/实施/检查/处理405.Oscillator:振荡器406.Adapter: 适配器407.Spindle:轴心408.WIP: Work in process半成品Waive:特别采用409.FMEA:Protentical Failure Mode and Effects Analysis失效模式与效应分析410.M SA: Measurement Systems Analysis 量测系统分析411.Benchmarking:竞争标竿412.Roka Yoke 防错法413.Mistake Proofing 防呆法414.Fool-Proof System防呆系统415.Specified Requirement:规定要求416.AOQ: Average Outgoing Quality 平均检出质量AOQL: Average OutgoingQuality Limit 平均检出质量界限417.Benchmarking 基准点418.Calibration 校准419.Continuous improvement 持续改进420.Deviation / Substitution 偏差/ 置换421.ESD: Electrostatic discharge 静电释放422.FMEA: Failure Mode Effect Analysis 失误模式效应分析423.First Article approval 产品的首次论证424.First pass yield 一次性通过的成品率425.First sample inspection 第一次样品检验426.FMECA: Failure mode effect and critically analysis 失误模式,效应及后果分析427.Life Testing 寿命试验Lot traceability 批量可追溯性428.NONCONFORMANCE 不符合429.OUT-OF-CONTROL PROCESS 失控工序430.Pilot Application 试产(试用) 431.P PM: Parts per million 百万分之一432.Process capability index 工序能力指数433.Total quality management 全面质量管理434.Site Audit 现场审核435.Failure rate percentage 失误百分率436.Customer complaints 客户投诉437.Root cause analysis of failures 失误根原分析yout Inspection:全尺寸检验439.Bulk material:散装材料440.Feasibility Reviews:可行性审查441.P re-launch:量产前442.Stock rotation :存货周转443.Inventory levels:最低库存量444.Interim action:临时措施445.Permanent action:永久措施446.vibration test振动试验447.Conveyer流水线物料板448.fasten锁紧(螺丝)449.fuse machine热熔机450.SOP制造作业程序451.w ork cell工作间452.trolley台车453.carton纸箱454.电阻Resistor455.电容Capacitor456.晶振Crystal resonator 457.开关Switch458.插座Jack459.插头Plug460.工艺Workmanship 461.喷油Conformal coating 462.插件Insertion463.回焊炉Reflowing oven 464.飞达feeder465.吸嘴466.钢网Stencil467.抛料468.线股Strand469.松香Flux470.尾数WP471.锡炉DIP472.暂置Hold473.全检Sorting474.条形码Bar code475.日期编码Date code476.标准作业指导书SOP Standard operation plan477.过电压保护OVP Over voltage protect 478.汶波/噪声Noise479.连接器Connector480.线材Cable481.C TQ=critical to quality。
Injection Factory注塑厂Oil tank capacity油箱容量Injection Workshop注塑车间Pump motor power油泵电机Plastic Products Factory塑胶厂Barrel heating power电热容量Machinery Moulding Factory机械制模厂Total wattage总用电量Gas assisted injection molding气辅成型Machine weight机器重量Precision injection精密注塑Machine diamension机器外型尺寸Thermo plastic热塑性塑料辅助设备Auxiliary equipments注塑部分Injection unitRobotic arm机械手
Injection moulding machine注塑机Core pulling device插抽芯装置Clamping force锁模力Unscrewing device铰牙装置Opening force开模力LCD液晶显示屏Platen size模板尺寸Cooling tower冷却塔Distance between tie bare导柱间距Air cooling type dryer风冷式干燥器Minimum mold height 最小使用模厚Water cooling type dryer水冷式干燥器Opening stroke开模行程Granulator粉碎机Maximum opening distance最大开模间距Cutting house粉碎室Ejector force顶出力Tilt-back hopper入料斗Ejector stroke顶出行程Granulate over flow溢料口Screw diameter螺杆直径Fixed hopper/Hopper dryer固定式/干燥料斗Injection pressure射出压力Automatic feed device自动上料器Theoretical shot volume 理论射出压力Insalated tank保温式桶Four-stage holding pressure四级保压压力Material storage tank储料桶Proportional back pressure比例背压Suction box吸料盒Maximum shot weight射出量Blower 风机Injection rate射出率Start-up timer定时器Plasticizing塑化能力Base底座Metering speed/pressure溶胶速度/压力其他OthersScrew stroke螺杆转速Standard linear pot标准行程电子尺Number of temperature control温控段数Injection pressure sensor射胶压力传感器Injection stroke射出行程Standard nitrided screw标准氮化螺杆Maximum hydraulic pressure系统最大压力Standard/Extended nozzle标准/加长射嘴Mold thickness range容模量Pin point gate system细水口系统Hardness androbustness of frame机架Three plate type system简化型细水口系统Injection unit射台Top clamp plate顶板Barrel套筒Ejector plate 顶出板Hydraulic part液压元件Retaining plate 顶出固定板Seal密封件Bottom clamp plate底板Proportional pressure valve比例压力阀A-plate /fixed half定模板Flow vavle流量阀B-plate/movable half动模板Throttle valve截流阀Support plate动模垫板Close loop control闭环控制Cavity plate 凹模板Clamping system锁模系统Core plate凸模板Injection system射出系统Thick wall壁厚Hydrulic and electric system油压电力系统Front/back mould plate 前/后模板Slide system 滑模系统Runner stripper plate水口推板Centralized cooling system 中央冷却系统Stripper/push plate推板Oil circuit油路Bolster/sub-base 垫板Hydraulic shut-off nozzle油压封嘴Spacer block方铁Automatic purging自动清料Ejector retainer plate面针板Drooling prevention防流延Ejector plate底针板Core pull sequence抽芯动作方式Centre-drilling 中心孔High speed clamping快速锁模Impression/cavity 型腔Auto-mold height adjustment 自动调模Mold base模胚模具部分Mold unit标准件Standard partPrecision mold精密模具Locating ring/Register ring定位环Resin flow in cavity注塑模拟流动分析Sprue bush浇口衬套/主流道衬套Undercut moulding 侧向分型模Sprue puller 浇道拉杆Two-plate mould 双板式注射模Thermoset sprue bush热固性塑料浇口衬套Multi-imprssion mould 多型腔模Guide pin导柱Servomechanism 伺服机构Guide bush 导套模架Mold base/Die-setSlideway导轨
