注塑机常用英语

注塑模具英语词汇-CAL-FENGHAI.-(YICAI)-Company One1注塑模具英语词汇一、工程部 / Design department:1) Designer - 设计师。

2) Assembly drawing - 模具组装图。

3) Mold layout - 模具结构图。

4) 2D product drawing - 2D产品图。

5) 3D product data - 3D产品数据。

6) Part drawing - 散件图。

7) Insert molding - 镶件模。

8) 2 color mold / Double injection tool - 双色模。

9) Hydraulic system - 油/水压系统。

10) Parting line - 分模线。

11) Air venting - 排气槽。

12) Cooling system - 冷却系统。

13) Screw - 镙丝。

14) Hot runner system - 热流道。

15) Valve gate - 伐针入水口。

16) Fan gate - 扇型入水口。

17) Pin point gate - 针点进胶。

18) Moon gate / Banana gate - 香蕉，象牙入水口。

19) Submarine gate - 潜水口。

20) Injection machine tonnage - 注塑机吨数。

21) Number of cavity - 穴数。

22) Steel - 钢材。

23) Copper - 铜。

24) Tungsten copper - 钨铜。

25) Beryllium copper - 铍铜。

26) Hardening - 加硬/淬火。

27) Tempering - 回火。

28) Chroming - 电镀。

29) Painting - 喷漆。

30) Resin - 胶材。

31) Printing - 丝印。

注塑机专业英语Revised on November 25, 2020钣金 machine cover / upper cover/ side cover锁模部分 clamping unit射胶部分 injection unit机架 machine frame / base电气系统 electric system液压系统 hydraulic system机械系统 mechanical system机门safety door / fixed door / movable door锁模部分 clamping unit电脑控制器 computer controller机械安全锁 mechanical safety interlock射胶部分 injection unit液压系统 hydraulic system电箱 electrical cabinet / cable机架分体线 stand split line机架螺丝孔 foundation bolt hole机架machine base / supporting frame理论注射容积 theoretical shot volume 实际注射量 shot weight螺杆直径 screw diameter注射压力 injection pressure注射速度 injection speed注射速率 injection rate螺杆长径比screw L/D ratio螺杆行程 screw stroke螺杆转速 screw speed熔胶能力plasticizing capacity锁模力 clamping force开模/锁模行程 mold clamping / opening stroke模板尺寸 platen size拉杆间距 distance between tie bars / rods模板最大距离 max. daylight容模量 mold thickness (min. & max.)顶出行程 hydraulic ejection stroke顶出力hydraulic ejection force顶针数 nos. of ejector pin液压系统压力hydraulic system pressure油泵马达 pump motor电热量 heating capacity 温度控制区数 nos. of temp control zones射嘴接触力 nozzle contact forceInjection射出Cooling time 冷却时间Holding time 锁模时间Injection alarm time 射出警报时间Injection start delayFinal cushion minimum valueChange-over to holding by valuePlasticizing end valueHydrarlic change-over pressure holdingScrewvalue for change-over to holdingChange-over to holding by enable valueHydraulic pressure in holding 锁模压力Filling stage pressure limitInjection speed 射出速度Injection注射Cooling time冷却时间Holding timeInjection alarm time注射报警时间Injection start delay注射开始延时Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Change-over to holding by enable valueHydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould closing关模Mould close force关模压力Mould closing safety time.. 时间Mould closing pressure.. 压力1st closing safety stage pressure合模一段压力1st mould closing speed ...成型速度1st stage mould closing speed1st stage mould closing safety position.....位置High pressure start position高压锁模位置Number of repeat mould closing movement..重复次数Holding time 保压时间Injection start delay 注射延迟Injection注射Cooling time冷却时间Holding time保压时间Injection alarm time注射报警时间Injection start delay注射开始延时(注射延时启动延时)Final cushion minimum value最后段位置（最小余量）Change-over to holding by value切换到锁模（保压由位置切换）Plasticizing end value预塑重终点（熔胶终止）Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Change-over to holding by enable value保压由位置切换Hydraulic pressure in holding锁模力（保压）Filling 填充Injection alarm time 射胶时间Injection start delay 延迟射胶Final cushion minimum value 不知道这个是在哪个页面或项目下，如果是射胶那应该是：最小射胶终点（应该是品质项目设置的）Change-over to holding by value不知道这个是在哪个页面或项目下，如果是射胶那应该是：最大射胶终点（应该是品质项目设置的）Plasticizing end value终点位置。

钣金 machine cover / upper cover/ side cover 锁模部分 clamping unit射胶部分 injection unit机架 machine frame / base电气系统 electric system液压系统 hydraulic system机械系统 mechanical system机门 safety door / fixed door / movable door 锁模部分 clamping unit电脑控制器 computer controller机械安全锁 mechanical safety interlock射胶部分 injection unit液压系统 hydraulic system电箱 electrical cabinet / cable机架分体线 stand split line机架螺丝孔 foundation bolt hole机架 machine base / supporting frame理论注射容积 theoretical shot volume实际注射量 shot weight螺杆直径 screw diameter注射压力 injection pressure注射速度 injection speed注射速率 injection rate螺杆长径比 screw L/D ratio螺杆行程 screw stroke螺杆转速 screw speed熔胶能力 plasticizing capacity锁模力 clamping force开模/锁模行程 mold clamping / opening stroke 模板尺寸 platen size拉杆间距 distance between tie bars / rods模板最大距离 max. daylight容模量 mold thickness (min. & max.)顶出行程 hydraulic ejection stroke顶出力 hydraulic ejection force顶针数 nos. of ejector pin液压系统压力 hydraulic system pressure油泵马达 pump motor电热量 heating capacity温度控制区数 nos. of temp control zones射嘴接触力 nozzle contact forceInjection射出Cooling time 冷却时间Holding time 锁模时间Injection alarm time 射出警报时间Injection start delayFinal cushion minimum valueChange-over to holding by valuePlasticizing end valueHydrarlic change-over pressure holding Screwvalue for change-over to holdingChange-over to holding by enable valueHydraulic pressure in holding 锁模压力Filling stage pressure limitInjection speed 射出速度Injection注射Cooling time冷却时间Holding timeInjection alarm time注射报警时间Injection start delay注射开始延时Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Change-over to holding by enable valueHydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould closing关模Mould close force关模压力Mould closing safety time.. 时间Mould closing pressure.. 压力1st closing safety stage pressure合模一段压力1st mould closing speed ...成型速度1st stage mould closing speed1st stage mould closing safety position.....位置High pressure start position高压锁模位置Number of repeat mould closing movement..重复次数Holding time 保压时间Injection start delay 注射延迟Injection注射Cooling time冷却时间Holding time保压时间Injection alarm time注射报警时间Injection start delay注射开始延时(注射延时启动延时)Final cushion minimum value最后段位置（最小余量）Change-over to holding by value切换到锁模（保压由位置切换）Plasticizing end value预塑重终点（熔胶终止）Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Change-over to holding by enable value保压由位置切换Hydraulic pressure in holding锁模力（保压）Filling 填充Injection alarm time 射胶时间Injection start delay 延迟射胶Final cushion minimum value 不知道这个是在哪个页面或项目下，如果是射胶那应该是：最小射胶终点（应该是品质项目设置的）Change-over to holding by value不知道这个是在哪个页面或项目下，如果是射胶那应该是：最大射胶终点（应该是品质项目设置的）Plasticizing end value终点位置。

注塑英语大全成型工艺流程及条件介绍Molding technique procedure and parameter introduction 第一节成型工艺Section 1 molding technique.1.成型工艺参数类型Sorts of molding parameter.(1).注塑参数ction parameter.a.注射量ction rate.b.计量行程Screw back positionc.余料量Cushiond.防诞量Sucking back ratee.螺杆转速Screw speedf.塑化量Plastic0 rateg.预塑背压Screw back pressureh.注射压力和保压压力ction pressure and holding pressurei.注射速度ction speed(2)合模参数Clamping parametera.合模力Clamping forceb.合模速度Clamping speedc.合模行程.Clamping stroked.开模力Opening force e.开模速度Opening speed f.开模行程Opening positiong.顶出压力Ejector advance pressureh.顶出速度Ejector advance speedi.顶出行程Ejector advance position2.温控参数Temperature parametera.烘料温度Dry resin material temperatureb.料向与喷嘴温度Cylinder temperature and nozzle temperaturec.模具温度Mold temperatured.油温Oil temperature3.成型周期Molding cyclea.循环周期Cycle timeb.冷却时间Cool timec.注射时间ction timed.保压时间Holding pressure timee.塑化时间Plant timf.顶出及停留时间Knocking out and delay timeg.低压保护时间Mold protect time成型工艺参数的设定须根据产品的不同设置. Molding technique parameter setting differs depending on type of product第二节成型条件设定Section 2 Molding parameter Setting按成型步骤:可分为开锁模,加热,射出,顶出四个过程.Molding steps: mold opening/closing, heating ction and knocking out.开锁模条件: Mold opening parameter:快速段中速度High-speedmid-speed低压高压速度Low pressure high pressure speed锁模条件设定: Mold closing parameter setting1锁模一般分:快速→中速→低压→高压Mold closing: high-speed →low-speed →low pressure→high pressure。

注塑英语大全成型工艺流程及条件介绍Molding technique procedure and parameter introduction 第一节成型工艺Section 1 molding technique.1.成型工艺参数类型Sorts of molding parameter.(1).注塑参数ction parameter.a.注射量ction rate.b.计量行程Screw back positionc.余料量Cushiond.防诞量Sucking back ratee.螺杆转速Screw speedf.塑化量Plastic0 rateg.预塑背压Screw back pressureh.注射压力和保压压力ction pressure and holding pressurei.注射速度ction speed(2)合模参数Clamping parametera.合模力Clamping forceb.合模速度Clamping speedc.合模行程.Clamping stroked.开模力Opening force e.开模速度Opening speed f.开模行程Opening positiong.顶出压力Ejector advance pressureh.顶出速度Ejector advance speedi.顶出行程Ejector advance position2.温控参数Temperature parametera.烘料温度Dry resin material temperatureb.料向与喷嘴温度Cylinder temperature and nozzle temperaturec.模具温度Mold temperatured.油温Oil temperature3.成型周期Molding cyclea.循环周期Cycle timeb.冷却时间Cool timec.注射时间ction timed.保压时间Holding pressure timee.塑化时间Plant timf.顶出及停留时间Knocking out and delay timeg.低压保护时间Mold protect time成型工艺参数的设定须根据产品的不同设置. Molding technique parameter setting differs depending on type of product第二节成型条件设定Section 2 Molding parameter Setting按成型步骤:可分为开锁模,加热,射出,顶出四个过程.Molding steps: mold opening/closing, heating ction and knocking out.开锁模条件: Mold opening parameter:快速段中速度High-speedmid-speed低压高压速度Low pressure high pressure speed锁模条件设定: Mold closing parameter setting1锁模一般分:快速→中速→低压→高压Mold closing: high-speed →low-speed →low pressure→high pressure。

注塑机各部件的中英文名称和作用shear剪切back pressure 背压no zzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubricati on 润滑Inject ion machi ne 啤机Shot size ( weight ）实际射胶量injectio n volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar cleara nee 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒,机筒clamp force 锁模力non-retur n valve 止回阀ope ning stroke 开模行程Injectio n pressure 射胶压力work horse 主力，主要设备Reserve pressure pack ing pressure 保压mold trial 试模shot （一）啤Decompress 减压oven烤炉，烘灶shri nkage rate 收缩率Reside nee time 滞留时间injection speed 注射速度booster time 增压时间Compressi on ratio 压缩比mold close time 合模时间Resin胶料Plasticizatio n 塑化，增塑viscosity 粘性，粘度con tam in ati on 污染，杂物Thermoplastic 热塑性塑料thermosett ing plastics 热固性塑料Booster time 增压时间feed喂料，填充purge 净化Flame retarda nt 阻燃degradati on 降解，软化regrind 再粉碎Water absorpti on 吸水rei nforce 增强，加固specific gravity 比重Elo ngation 延伸率den sity 密度melti ng point 熔点Polystyrene 聚苯乙烯（PS）Styrene 苯乙烯Acrylo nitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethyle ne 聚乙烯glass fiber 玻纤Conden sation 凝固，浓缩crystalli ne res in 结晶形塑料compre sio n moldi ng 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕weldi ng mark 溶合痕post screw in sert 螺纹套筒埋值self tapp ing screw 自攻螺丝striper plate 脱料板pist on 活塞cyli nder 汽缸套chip细碎物han dle mold 手持式模具（移转成型用模具）en capsulation moldi ng 低压圭寸装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井in sulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spi ndle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道weld ing line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子nner stripper plate 浇道脱料板guide pin 导销eject rod （bar）（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orie ntati on 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销（拉料杆）slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subari ne gate 潜入式浇口tunnel gate隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue浇口;溶渣入水：gate 进入位：gate locati on 水口形式：gate type 大水口：edge gate 细水口：pin-po int gate 水口大小：gate size 转水口：switch ing runn er/gate 唧嘴口径：sprue diameter 流道：runner 热流道：hot runner,hot manifold 热嘴冷流道:hot sprue/cold runner 唧嘴直流:direct sprue gate 圆形流道：roun d(full/half ru nner 流道电脑分析：mold flow analysis 流道平衡:runner bala nee 热嘴：hot sprue 热流道板：hot mani fold发热管：cartridge heater 探针:thermocouples 插头：conn ector plug插座：conn ector socket密圭寸/圭寸料：seal 运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connectorplug/socker模具零件：mold comp onents三板模：3-plate mold二板模：2-plate mold边钉/ 导边：leader pin /guide pin边司/ 导套：bush in g/guide bush ing中托司：shoulder guide bush ing 中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity in ter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）:nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity in sert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/ 油板：wedge wear plate 压条：plate撑头：support pillar唧嘴：sprue bush ing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spri ng rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞：pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：part ing locks活动臂：lever arm复位键、提前回杆：early retur n bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：part ing surface support bala nee 模排气：part ing line venting回针碰料位：return pin and cavity in terfere nee 模总高超出啤机规格：mold base shut hight顶针碰运水：water line in terferes withejector pin料位出上/ 下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件：Do not use (core/cavity) in sert用铍铜做镶件：use beryllium copper insert初步(正式)模图设计：prelii nary (fin al) mold desig n 反呵：reverse core弹弓压缩量：spri ng compressed len gth稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷去卩：eve n cooli ng扣模：sticking热膨胀：thero expansion公差：toloranee铜公(电极)：copper electrode塑料成形模具mould for plastics热塑性塑料模mould for thermoplastics热固性塑料模mould for thermosets压缩模compressi on mould压注模、传递模tran sfer mould注射模injectio n mould热塑性塑料注射模injectio n mould for thermoplastics 热固性塑料注射模injectio n mould for thermoses定模statio nary mould fixed half动模movable mould moving half定模座板fixed clamp plate, top clampi ng plate. top plate动模座板movi ng clamp plate. bottom clampi ng plate. bottom plate上模座板upper clampi ng plate下模座板lower clampi ng plate凹模固定板cavity-reta iner plate型芯固定板core-reta iner plate凸模固定板pun ch-reta iner plate模套chase. bolster. frame支承板back ing plate. supprr plate垫块spacer parallel 支架ejector housing. mould base leg abrasive grinding 强力injectio n mould 注塑模injection 注射in-line-of-draw 直接脱模in sert 嵌件in serted die 嵌入式凹模in specti on 检查，监督in stallati on 安装Surface Appeara nee 夕卜观Gloss in ess/gloss finish 光洁度Matt fini sh/matt surface 毛面Glass fiber rich surface/glass emerge nee on the surface 玻纤外露Bloomi ng/surface bloomi ng 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittle ness 脆Bubbles/trapped gas 气泡Void 孑LBur n marks 烧伤FR failed 阻燃不合格Flame rati ng V-2 阻燃V-2 Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 粒子不密/蜜蜂窝Low impact/te nsile etc 物理性能低High flow/filler con te nt etc 流动性/ 填充…过高Lon gs/fi nes/doubles 长粒/ 碎屑/ 连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孑LGlass bun dles 玻纤结团Product was rejected due to 产品不能接受因为…High moisture level 高水分Warpage/warped 翘曲Shrin kage/shri nk 收缩Si nk marks 缩影Short shot/short moldi ng 打不满Distortio n 变形Over dime nsion 尺寸过大Un der dime nsion 尺寸过小Flash ing 飞边Discolorati on 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模An tioxida nt 抗氧剂Flame retarda nt age nt 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Rovi ng glass fiber 粗纱/ 长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybde num disulfide/moly/MoS2 二硫化钼Colora nt 着色剂Pigme nt 颜料Dye染料Accepted product specificati on 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra … 添加多一点…Reduced …content 减少…含量Dropped/reduced …by x % 减少…含量Con firmed color sta ndard 确认颜色标准Approved color sta ndard 认可颜色标准Re-c on firmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Un dergoi ng heat agi ng test 在做热老化实验Product is un der testi ngReceived first order接了第一个定单Expected to finish by Expected order is xMT产品在测试当中•预计在…完成预计定单量…吨Estimated annu al/m on thly con sumption预计年/月用量SPC statistic process con trol品管保证Quality Assuranee品管控制Quality control来料检验IQC In comi ng quality con trol巡检IPQC In-process quality control校对calibration动态试验dynamic test环境试验Environmental test非破坏性试验non-destructive test光泽gloss击穿电压(dielectric) breakdown voltage拉伸强度tensile strength冷热骤变试验thermal shock test环境试验炉Environmental chamber盐雾实验salt spray test绝缘电阻测试验仪In sulat ing resista nee meter 内应力internal stress疲劳fatigue蠕变creep试样specimen撕裂强度tear strength缩痕shrink mark, sink mark耐久性durability抽样sampling样品数量sample size AQL Acceptable Quality level批量lot size抽样计划sampling plan OC曲线operation curve试验顺序sequenee of tests环境温度ambient temperature可焊性solderability阻燃性flame resista nee总经理办公室General manager ' s office企管咅E Enterprise management department (EM)行政咅 E Admi ni strati on departme nt (AD)销售部Sales department (SD)财务部Financial department (FD)技术部Tech no logy departme nt (TD)物控部Production material control department (PMC)生产部Production department(PD)manu facturi ng 模具咅E Mold manufacturing department, Toolingdepartme nt (TM)实用标准文案品管咅E Quality Assuranee department (QA)冲压车间Stamp workshop, press workshop注塑车间injection workshop装配车间Assembly workshop模具装配车间Mold and die Assembly workshop 金属加工车间metal machine workshop电脉冲车间Electric discharge process workshop 线切割车间wire cutting process workshop 工磨车间Grinding workshop总经理General manager (GM)副总经理Vice-general manager经理manager董事长preside nt副董事长Vice-preside nt XX部门经理Manager of XX department主任、主管supervisor拉长Line leader组长Foreman, forelady秘书secretary文员clerk操作员operator助理assistant精彩文档。