齿轮参数中英对照

齿轮基本术语(中英文对照)齿轮 Toothed gear；Gear齿轮副 Gear pair平行轴齿轮副 Gear pair with parallel axes相交轴齿轮副 Gear pair with intersecting axes 齿轮系 Train of gears行星齿轮系 Planetary gear train齿轮传动 Gear drive；Gear transmission配对齿轮 Mating gears小齿轮 Pinion大齿轮 Wheel；Gear主动齿轮 Driving gear从动齿轮 Driven gear行星齿轮 Planet gear行星架 Planet carrier太阳轮 Sun gear内齿圈 Ring gear；Annulus gear外齿轮 External gear内齿轮 Internal gear中心距 Centre distance轴交角 Shaft angle连心线 Line of centres减速齿轮副 Speed reducing gear pair增速齿轮副 Speed increasing gear pair齿数比 Gear ratio传动比 Transmission ratio轴平面 Axial plane基准平面 Datum plane节平面 Pitch plane端平面 Transverse plane法平面 Normal plane分度曲面 Reference surface节曲面 Pitch surface齿顶曲面 Tip surface齿根曲面 Root surface基本齿廓 Basic tooth profile基本齿条 Basic rack产形齿条 Counterpart rack产形齿轮 Generating gear of a gear产形齿面 Generating flank基准线 Datum line轮齿 Gear teeth；Tooth齿槽 Tooth space右旋齿 Right-hand teeth左旋齿 Left-hand teeth变位齿轮 Gears with addendum modification；X-gears高度变位圆柱齿轮副 X-gear pair with reference centre distance 角度变位圆柱齿轮副 X-gear pair with modified centre distance 高度变位锥齿轮副 X-gear pair without shaft angle modification 角度变位圆柱齿轮副 X-gear pair with shaft angle modification 变位系数 Modification coefficient变位量 Addendum modification径向变位系数 Addendum modification coefficient中心距变位系数 Centre distance modification coefficient圆柱齿轮 Cylindrical gear顶圆 Tip circle根圆 Root circle齿距 Pitch齿距角 Angular pitch公法线长度 Base tangent length分度圆直径 Reference diameter节圆直径 Pitch diameter基圆直径 Base diameter顶圆直径 Tip diameter根圆直径 Root diameter齿根圆角半径 Fillet radius齿高 Tooth depth工作高度 Working depth齿顶高 Addendum齿根高 Dedendum弦齿高 Chordal height固定弦齿高 Constant chord height齿宽 Facewidth有效齿宽 Effective facewidth端面齿厚 Transverse tooth thickness法向齿厚 Normal tooth thickness端面基圆齿厚 Transverse base thickness法向基圆齿厚 Normal base thickness端面弦齿厚 Transverse chordal tooth thickness固定弦齿厚 Constant chord端面齿顶厚 Crest width法向齿顶厚 Normal crest width端面齿槽宽 Transverse spacewidth法向齿槽宽 Normal spacewidth齿厚半角 Tooth thickness half angle槽宽半角 Spacewidth half angle压力角 Pressure angle齿形角 Nominal pressure angle圆弧圆柱蜗杆 Arc-contact worm；hollow flank worm；ZC-worm直廓环面蜗杆 Enveloping worm with straight line grneratrix；TA worm平面蜗杆 Planar worm wheel；P-worm wheel平面包络环面蜗杆 Planar double enveloping worm；TP-worm平面二次包络蜗杆 Planar double-enveloping worm wheel；TP-worm wheel锥面包络环面蜗杆 Toroid enveloping worm wheel；TK-worm wheel 渐开线包络环面蜗杆 Toroid enveloping worm hich involute holicoid generatrix；TI-worm锥蜗杆 Spiroid锥蜗轮 Spiroid gear锥蜗杆副 Spiroid gear pair中平面 Mid-plane长幅内摆线 Prolate hypocycloid短幅内摆线 Curtate hypocycloid渐开线 Involute；Involute to a circle延伸渐开线 Prolate involute缩短渐开线 Curtate involute球面渐开线 Spherical involute渐开螺旋面 Involute helicoid阿基米德螺旋面 Screw helicoid球面渐开螺旋面 Spherical involute helicoid圆环面 Toroid圆环面的母圈 Generant of the toroit圆环面的中性圈 Middle circle of the toroid圆环面的中间平面 Middle-plane of the toroid圆环面的内圈 Inner circle of the toroid啮合干涉 Meshing interference切齿干涉 Cutter interference齿廓修型 Profile modification；Profile correction修缘 Tip relief修根 Root relief齿向修形 Axial modification；Longitudinal correction齿端修薄 End relief鼓形修整 Crowning鼓形齿 Crowned teeth挖根 Undercut瞬时轴 Instantaneous axis瞬时接触点 Point of contact瞬时接触线 Line of contact端面啮合线 Transverse path of contact啮合曲面 Surface of action啮合平面 Plane of action啮合区域 Zone of action总作用弧 Total arc of transmission端面作用弧 Transverse arc of transmission 纵向作用弧 Overlap arc总作用角 Total angle of transmission端面作用角 Transverse angle of transmission 纵向作用角 Overlap angle总重合度 Total contact ratio端面重合度 Transverse ratio纵向重合度 Overlap ratio标准齿轮 Standard gears非变位齿轮 X-gero gear标准中心距 Referencr centre distance名义中心距 Nominal centre distance分度圆柱面 Reference cylinder节圆柱面 Pitch cylinder基圆柱面 Basic cylinder齿顶圆柱面 Tip cylinder齿根圆柱面 Root cylinder节点 Pitch point节线 Pitch line分度圆 Reference circle节圆 Pitch circle基圆 Basic circle定位面 Locating face外锥距 Outer cone distance内锥距 Inner cone distance中点锥距 Mean cone distance背锥距 Back cone distance安装距 Locating distance轮冠距 Tip distance；crown to back冠顶距 Apex to crown偏置距 Offset齿线偏移量 Offset of tooth trace分锥角 Reference cone angle节锥角 Pitch cone angle顶锥角 Tip angle根锥角 Root angle背锥角 Back cone angle齿顶角 Addendum angel齿根角 Dedendum angle任意点压力角 Pressure angle at a point任意点螺旋角 Spiral angle at a point中点螺旋角 Mean spiral angle大端螺旋角 Outer spiral angle小端螺旋角 Inner spiral angle蜗杆 Worm蜗轮 Worm wheel蜗杆副 Worm gear pair圆柱蜗杆 Cylindrical worm圆柱蜗杆副 Cylindrical worm pair环面蜗杆 Enveloping worm环面蜗杆副 Enveloping worm pair阿基米德蜗杆 Straight sided axial worm；ZA-worm 渐开线蜗杆 Involute helicoid worm；ZI-worm法向直廓蜗杆 Straight sided normal worm；ZN-worm 锥面包络圆柱蜗杆 Milled helicoid worm；ZK-worm 椭圆齿轮 Elliptical gear非圆齿轮副 Non-circular gear pair圆柱针轮副 Cylindsical lantern pinion and wheel 针轮 Cylindsical tan tein gear ；pin-wheel谐波齿轮副 Harmoric gear drive波发生器 Wave generator柔性齿轮 Flexspine刚性齿轮 Circular spline非圆齿轮 Non-circular gear分度圆环面 Reference tosoid。

花键齿轮参数中英文对照渐开线花键 involute spline未注公差 undeclared tolerance未注倒角 undeclared chamfer调质 thermal refining端口 port chamfer模数 modulus齿形角 tooth profile angle变位系数 stand-off error齿圈径向跳动 geared ring radial runout公法线长度及偏差 common normal跨齿数 spanned tooth count高频淬火 high-frequency quenching配对齿轮 mating gear螺旋角 spiral angle压力角 pressure angle螺旋升角 lead angle图号 figure number齿厚 tooth thickness螺旋线 helix蜗杆 worm齿轮 gear齿轴 gear shaft转子轴 rotor shaft精度等级 precision class汽车构造词汇汽车 automobile拖拉机 tractor铁路机车 locomotive有轨电车 tram无轨电车 trolley军用车辆 military vehicle蒸汽机 steam engine煤气机 gas engine汽油机 gasoline engine国民经济 national economy国内生产总值 (GDP) Gross Domestic Production全拆散 (CKD) Completely Knock Down半拆散 (SKD) Semi-Knock Down改革开放 reform and opening技术引进 technical import国产化 localization支柱产业 pillar estate轿车 car客车 bus, coach货车 truck, lorry公路用车 road vehicle非公路用车 off-road vehicle发动机 engine机体 engine body曲柄连杆机构 crank-connecting rod mechanism 配气机构 valve timing mechanism供给系 fuel supply system冷却系 cooling system润滑系 lubricating system点火系 ignition system起动系 starting system底盘 chassis传动系 power train离合器 clutch变速器 gear box传动轴 propeller shaft驱动桥 drive axle行驶系 running gear车架 frame悬架 suspension前轴 front axle桥壳 axle housing车轮 wheel转向系 steering system转向盘 steering wheel转向器 steering gear转向传动装置 steering linkage助力装置 power assisting device制动系 braking system控制装置 control device供能装置 power supply device传动装置 transfer device制动器 brake车身 body车前板制件 front end panels车身壳体 body shell车门 door车窗 window附属装置 auxiliary device货箱 carrying platform发动机前置后轮驱动 (FR) front engine rear drive 发动机前置前轮驱动 (FF) front engine front drive 发动机后置后轮驱动 (RR) rear engine rear drive发动机中置后轮驱动 (MR) midship engine rear drive 全轮驱动 (nWD) all wheel drive驱动力 tractive force阻力 resistance滚动阻力 rolling resistance空气阻力 air resistance, drag上坡阻力 gradient resistance附着作用 adhesion附着力 adhesive force附着系数 coefficient of adhesion第一章发动机工作原理二冲程发动机 two stroke engine四冲程发动机 four stroke engine水冷发动机 water cooled engine风冷发动机 air cooled engine上止点 (UDP) upper dead point下止点 (LDP) lower dead point活塞行程 stroke汽缸直径 bore工作容积 working volume排量 swept volume, displacement进气行程 intake stroke压缩行程 compression stroke压缩比 compression ratio做功行程 working stroke爆燃，敲缸 detonation, knock排气行程 exhaust stroke示功图 indicating diagram汽缸体 cylinder block汽缸盖 cylinder head油底壳 oil sump活塞 piston连杆 connecting rod曲轴 crankshaft飞轮 flywheel进气门 intake valve排气门 exhaust valve挺柱 tappet推杆 push rod摇臂 rocker凸轮轴 camshaft正时齿轮 timing gear燃油箱 fuel tank燃油泵 fuel pump汽油滤清器 gasoline filter化油器 carburetor空气滤清器 air cleaner进气管 intake manifold排气管 exhaust manifold火花塞 spark plug点火线圈 ignition coil断电器 breaker蓄电池 storage battery发电机 generator水泵 water pump散热器 radiator风扇 fan放水阀 drain valve水套 water jacket分水管 distributive pipe机油泵 oil pump集滤器 suction filter限压阀 relief valve润滑油道 oil passage机油滤清器 oil filter机油冷却器 oil cooler起动机 starting motor有效功率 effective power有效转矩 effective torque燃油消耗率 specific fuel consumption发动机转速特性 engine speed characteristic 节气门开度 throttle percentage部分特性 partial characteristic外特性 outer characteristic第二章曲柄连杆机构汽缸套 cylinder sleeve, cylinder liner发动机支承 engine mounting活塞顶 piston top活塞头部 piston head活塞裙 piston skirt开槽 slot活塞环 piston ring气环 compression ring油环 oil ring环槽 groove活塞销 piston pin主轴承 main bearing主轴承盖 main bearing cap主轴瓦 main shell连杆轴承 big end bearing连杆盖 big end cap起动爪 cranking claw带轮 pulley平衡重 counter weight发火顺序 firing order扭振减振器 torsional vibration damper第三章配气机构顶置气门 (OHV) Over Head Valve顶置凸轮轴 (OHC) Over Head Camshaft单顶置凸轮轴 (SOHC) Single Over Head Camshaft 双顶置凸轮轴 (DOHC) Dual Over Head Camshaft 多气门发动机 multi-valve engine气门间隙 valve clearance配气相位 timing phase气门杆 valve stem气门座 valve seat气门导管 valve guide气门弹簧 valve spring第四章汽油机供给系可燃混合气 combustion mixture消声器 silencer, muffler汽油 gasoline, petrol分馏 distil蒸发性 evaporating property热值 heat value抗爆性 anti-knock property辛烷值 (RON) Research Octane Number过量空气系数 coefficient of excessive air理论混合气 theoretical mixture稀混合气 thin mixture浓混合气 thick mixture主供油系统 main supply system怠速系统 idle system加浓系统 thickening system加速系统 accelerating system浮子 float浮子室 float chamber针阀 needle valve量孔 metering jet阻风门 choke滤芯 filter cartridge沉淀杯 sediment cup泵膜 pump diaphragm油浴式 oil bath type石棉垫 a**estos pad预热 pre-heating汽油直接喷射 gasoline direct injection电控 electronic control多点喷射 muti-point injection单点喷射 single point injection电路控制 circuit control分电器信号 distributor signal空气流量信号 airflow signal冷却水温信号 water temperature signal第五章柴油机供给系输油泵 transfer pump喷油泵 fuel injection pump高压油管 high pressure fuel pipe发火性 ignition property黏度 viscosity凝点 condensing point备燃期 pri-combustion period速燃期 rapid combustion period缓燃期 slow combustion period燃烧室 combustion chamber统一燃烧室 united chamber球形燃烧室 ball shape chamber涡流室 turbulence chamber预燃室 pri-combustion chamber喷油器 injector精密偶件 precise couple柱塞 plunger出油阀 delivery valve调速器 governor两速调速器 two speed governor全速调速器 full speed governor定速调速器 fixed speed governor综合调速器 combined governor气动调速器 pneumatic governor机械离心式调速器 mechanical centrifugal governor 复合式调速器 complex governor喷油提前角调节装置 advancer飞块 flyweight联轴节 coupling粗滤清器 primary filter细滤清器 secondary filter涡轮增压器 turbocharger中间冷却器 intermediate cooler第七章冷却系节温器 thermostat防冻液 anti-freezing liquid补偿水桶 compensation reservoirV-带 V belt百叶窗 shutter大循环 big circulation小循环 small circulation散热翅片 fins第八章润滑系润滑剂 lubricant压力润滑 pressure lubrication飞溅润滑 splash lubrication润滑脂 grease机油压力传感器 oil pressure sensor油封 oil seal旁通阀 bypass valve机油散热器 oil cooler机油尺 dip stick加机油口 oil filler曲轴箱通风 crankcase ventilation第九章点火系一次绕组 primary winding二次绕组 secondary winding热敏电阻 heat sensitive resistance点火提前 ignition advance分电器 distributor活动触点 moving contact固定触点 fixed contact分火头 distributor rotor arm电容器 condenser点火提前装置 ignition advancer离心式点火提前装置 centrifugal ignition advancer 真空式点火提前装置 vacuum ignition advancer辛烷值校正器 octane number rectifier中心电极 central electrode侧电极 side electrode瓷绝缘体 ceramic insulator跳火间隙 spark gap半导体点火系 semi-conductor ignition system晶体管 transistor二极管 diode三极管 triode无触点点火系 non-contact ignition system霍尔效应 Hall effect正极板 anode负极板 cathode隔板 separator电解液 electrolyte蓄电池格 battery cell接线柱 terminal电缆 cable硅整流交流发电机silicon rectified A.C. motor 转子 rotor定子 stator电刷 brush风扇叶轮 fan blade电压调节器 voltage regulator第十章起动系手摇起动 cranking电热塞 electric heater plug串激直流发电机 serial wound D.C. motor起动齿圈 starter ring电磁操纵机构 electro-magnetic control第十一章新型发动机三角活塞 triangular piston转子发动机 rotary engine自转 rotary motion, rotation公转 orbit motion轨迹 trajectory齿轮 gear齿圈 ring gear往复零件 reciprocal parts动平衡 dynamic balance燃气涡轮发动机 gas turbine第十二章汽车传动系机械式传动系 mechanical transmission液力机械式传动系 hydro-mechanical transmission 静液式传动系 static-hydraulic transmission电力式传动系 electrical transmission自动式传动系 automatic transmission减速 reduction可变速比 variable ratios有级变速 definite ratios无级变速 indefinite ratios无级变速器(CVT) Continuously Variable Transmission 一般布置 general layout发动机横置 lateral engine positioning分动器 transfer case, transfer box第十三章离合器接合柔和 smooth engagement分离彻底 thorough separation过载 overload摩擦表面 friction surface摩擦衬片 friction liner毂 hub主动部分 driving part从动部分 driven part花键 spline压盘 pressure plate离合器盖 cover plate分离杠杆 release lever分离套筒 release sleeve分离轴承 release bearing主缸 master cylinder工作缸 working cylinder分离* release fork间隙调整 clearance adjustment打滑 slip踏板 pedal踏板自由行程 pedal free stroke踏板工作行程 pedal working stroke铆钉，铆接 rivet双片离合器 dual disc clutch中央弹簧离合器 central spring clutch膜片弹簧离合器 diaphragm spring clutch非线性 non-linear第十四章变速器与分动器输入轴（第一轴）input shaft, drive shaft输出轴（第二轴）output shaft, main shaft中间轴 counter shaft倒挡轴 reverse gear shaft常啮合 constant mesh低速挡 low gear高速挡 high gear最高速挡 top gear空挡 neutral gear一挡 the first gear二挡 the second gear三挡 the third gear倒挡 reverse gear直接挡 direct gear超速挡 overdrive动力输出 power take-off换挡 shift啮合套 sliding sleeve同步器 synchronizer同步锥面 synchro cone变速杆 shifting lever手柄 handle球铰链 ball joint换挡拨* shifting fork自锁 self-lock互锁 inter-lock变速驱动桥 transaxle加力挡 low gear第十五章液力机械传动液力偶合器 hydraulic coupling泵轮 impeller涡轮 turbine叶片 blade液力变矩器 torque converter导轮 stator行星齿轮系 planetary gear system太阳轮 sun gear行星轮 planet pinion行星架 planet carrier齿圈 ring gear第十六章传动轴万向节 universal joint, U-joint十字轴式万向节Cardan type U-joint*子 yoke, fork十字轴 spider, center cross滚针轴承 needle bearing滑脂嘴（油嘴）lubricating fitting, nipple 等角速 constant angular velocity双联式万向节 dual Cardan type U-joint球*式万向节 Weiss type U-joint球笼式万向节 Rzeppa type U-joint星形套 inner race housing球形壳 outer race shell保持架，球笼 retainer, ball cage挠性万向节 flexible U-joint无缝钢管 seamless steel tube第十七章驱动桥主减速器 final drive主动（小）齿轮 drive pinion从动（大）齿轮 ring gear伞齿轮 bevel gear双曲面齿轮 hypoid gear单级减速 single reduction双级减速 double reduction贯通式主减速器 penetrable final drive双速主减速器 double gear (speed) final drive 轮边减速器 wheel reduction差速器 differential半轴齿轮 differential side gear差速锁 differential lock轴间差速器 inter-axle differential lock托森差速器 torque sensitive differential半轴 axle shaft全浮式半轴 float type axle shaft半浮式半轴 semi-float type axle shaft桥壳 axle housing桥壳后盖 final drive rear cover第十八章行驶系行驶系 running gear车架 frame车桥，车轴 axle悬架 suspension半履带式汽车 semi-caterpillar vehicle第十九章车架边梁式车架 ladder type frame纵梁 side rail横梁 cross member保险杠 bumper托架 bracket支承 support拖钩 tow hook中梁式车架 backbone type frame桁架式车架 lattice type frame第二十章车桥和车轮转向桥 steering axle桥梁 axle beam工字形断面 I-section转向节 knuckle主销 king pin轮毂 wheel hub转向轮定位 steering wheel alignment主销后倾 caster主销内倾 king pin inclination前轮外倾 camber前轮前束 toe-in转向驱动桥 steering and driving axle支持桥 support axle轮辋 rim轮辐 spoke车轮装饰罩 hub cap轮胎 tyre, tire胎冠 crown, tread花纹 pattern胎侧 side wall帘布层 cord, ply尼龙，锦纶 nylon带束层 belted layer内胎 tube垫带 protector胎圈 bead气门嘴 bleed valve气门芯 valve core子午线轮胎 radial tire无内胎轮胎 tubeless tire刺穿 puncture备胎 spare tire第二十一章悬架弹性元件 spring, elastic element减振器 sock absorber导向机构 control device横向稳定器（杆）stabilizer, anti-roll bar 悬架刚度 suspension stiffness簧载质量 sprung mass非簧载质量 unsprung mass静挠度 static deformation独立悬架 independent suspension车轮上跳（减振器压缩行程） jounce车轮回跳（减振器伸张行程） rebound双向作用减振器 double action shock absorber 单向作用减振器 single action shock absorber 筒式减振器 telescopic shock absorber吊环 link ring工作缸 working cylinder贮油缸 reservoir流通阀（进液阀）intake valve伸张阀 rebound valve压缩阀 compression valve补偿阀 compensation valve充气减振器 gas filled shock absorber压力可调减振器 pressure adjustable shock absorber 钢板弹簧 leaf spring中心螺栓 central bolt弹簧夹 clip螺旋弹簧 coil spring扭杆弹簧 torsional bar囊式空气弹簧 bellow type air spring膜式空气弹簧 diaphragm type air spring橡胶弹簧 rubber spring卷耳 spring eye吊耳 shackleU形螺栓 U-bolt弹簧盖板 spring plate副簧 auxiliary spring主簧 main spring横臂式悬架 transversal type suspension双横臂式悬架 double wishbone suspension转向轴线 steering axis纵摆臂式 trailing arm type滑柱式 strut type麦弗逊式 McPhaeson type平衡悬架 tandem axle suspension第二十二章转向系机械（手动）转向系 manual steering system转向盘 steering wheel转向轴 steering shaft转向柱 steering column转向传动轴 steering drive shaft转向器 steering gear直拉杆 drag link转向节 knuckle转向节臂 knuckle arm梯形臂 steering arm横拉杆 tie rod转向轮偏转角关系 steering geometry转弯半径 turning radius循环球式转向器 recirculating ball steering gear转向螺杆 steering screw转向螺母 steering nut齿扇 sector齿轮齿条式转向器 rack and pinion steering gear蜗杆曲柄指销式转向器 worm and crankpin steering gear 动力转向 power steering转向油罐 steering reservoir转向油泵 steering oil pump第二十三章制动系鼓式制动器 drum brake制动蹄 brake shoe轮缸 wheel cylinder制动底板 brake base plate调整凸轮 adjustable cam制动蹄回位弹簧 retainer spring领蹄 leading shoe从蹄 trailing shoe盘式制动器 disc brake制动钳 brake calipers制动盘 brake disc液压制动系 fluid braking system制动液 brake fluid制动主缸 master cylinder气压制动系 pneumatic braking system空气压缩机 air compressor制动气室 brake chamber贮气筒 reservoir制动阀 brake valve气压调节阀 air pressure governor伺服制动系 servo braking system真空助力器 vacuum booster防抱死制动系 (ABS) Anti-lock Braking System辅助制动器 auxiliary brake缓速器 retarder排气制动 exhaust braking第二十四章车身车身壳体 body shell非承载式车身 separate frame construction承载式车身 unitary construction, integral body发动机舱 engine compartment客厢，乘客室 passenger compartment行李箱 trunk发动机罩 hood, bonnet前翼板 front fender, front wing 前挡泥板 front fender apron前围板 dash board, fire wall前风窗 windscreen, windshield 前围 cowl, shroud顶盖 roof地板 floor panel行李箱盖 trunk lid, deck lid后围板 rear end panel前柱front pillar, “A” pillar 中柱center pillar, “B” pillar 后柱rear pillar, “C” pillar 上边梁 roof rail门槛 rocker panel仪表板 instrument panel遮阳板 sun visor刮水器 wiper后视镜 rear view mirror门锁 door lock玻璃升降器 window regulator密封条 weather strip暖气装置 heater空调装置 air conditioner座椅 seat头枕 head restraint安全带 safety seat belt钢化玻璃 toughened glass夹层玻璃 laminated glass货箱 carrying platform边板 side board后板 tail board前板 head board地板，底板 floor board栓杆 tightening latch第二十五章附属设备车速表 speedometer里程表 mileage recorder机油压力表 oil pressure gauge 燃油表 fuel gauge水温表 water temperature gauge 电流表 ammeter前大灯 head lamp转向指示灯 turning indicator制动信号灯 braking signal light报警信号装置 warning signal附表一般工程词汇长度 length宽度 width高度 height深度 depth距离 distance间隙 clearance位移 displacement面积 area体积 volume重量 weight质量 mass比重 specific gravity密度 density时间 time周期 period加速度 velocity, speed重力加速度 acceleration of gravity 力 force合力 resultant分力 component力矩 moment转矩 torque, twisting moment弯矩 bending moment压强 pressure大气压 atmospheric pressure声压级 (SPL) Sound Pressure Level 应力 stress应变 strain变形 deformation拉伸 stretching压缩 compressing弯曲 bending扭转 twisting强度 strength刚度 stiffness硬度 hardness黏度 viscosity运动黏度 kinematic viscosity能量 energy动能 kinetic energy位能 potential energy功 work功率 power温度 temperature热 heat热容量 thermal capacity比热 specific heat热功当量Joule’s equivalent传热系数 coefficient of heat transfer 加热 heating冷却 cooling膨胀 expansion固体 solid液体 liquid气体 gas蒸发 evaporation溶解 dissolve融化 melt凝结 condensation凝固 solidification电路 electric circuit串联 serial connection并联 parallel connection电荷 electric charge电压 voltage电位 potential电流 current直流 (D.C.) Direct Current交流 (A.C.) Alternative Current电阻 resistance电容量 capacity电容器 condenser电感 inductance电极 electrode正极 anode负极 cathode电离 ionization电解 electrolysis电镀 electroplating电泳 electrophoresis磁场强度 magnetic field intensity磁通量 magnetic flux光通量 luminous flux光照度 photometric quantity发光强度 luminous intensity工程图 technical drawing图板 drawing board图纸 drawing paper描图纸 tracing paper投影 projection前视图 front end view侧视图 side view左视图 left end view右视图 right end view俯视图 plan view剖面 section剖视 section view实线 full line虚线 broken line, dotted line 点划线 chain line尺寸线 dimension line方形 square长方形 rectangle三角形 triangle圆形 circle内接圆 inscribed circle外切圆 circumscribed circle 直尺 ruler三棱尺 triangular scale三角板 set square丁字尺 tee square, T square 圆规 compasses分规 divider曲线板 curve鸭嘴笔 drawing pen锤子 hammer斧子 ax, axe螺丝刀 screw driver扳手 wrench, spanner活动扳手 adjustable wrench扳手套筒 socket钳子 pliers火钳子 tongs虎钳 vice刀子 knife刮刀 scraper剪子 scissors镊子 tweezers夹子 clip夹紧器 clamp锉刀 file凿子，錾子 chisel冲子 punch锥子 awl锯子 saw刨子 plane钻 drill砧铁 anvil直角尺 square内卡规 inside calipers外卡规 outside calipers游标卡尺 vernier calipers千分卡尺 micrometer guage高度尺 height gauge千分表 dial indicator水平（泡）尺 water level画针盘 marking gauge螺纹 threads螺栓 bolt双头螺柱 stud螺钉 screw十字槽螺钉 cross recessed screw 螺母 nut开槽螺母 castle nut蝶形螺母 fly nut, wing nut垫圈 washer弹簧垫圈 lock washer开口销 split pin, cotter pin键 key花键 spline直齿齿轮 spur gear斜齿齿轮 helical gear伞齿轮 bevel gear球轴承 ball bearing滚子轴承 roller bearing滚针轴承 needle roller bearing 轴承外圈 outer race轴承内圈 inner race隔离罩，保持架 cage, retainer 铸造，铸件 casting锻造，锻件 forging轧制，轧制件 rolling冲压，冲压件 stamping焊接，焊缝 welding电弧焊 arc welding气焊 oxyacetylene welding点焊 spot welding铆接，铆钉 rivet机械加工 machine work切削 cutting车削 turning刨削 planing铣削 milling钻削 drilling绞孔 fraising磨削 grinding镗削 boring拉削 broaching抛光 polishing热处理 heat treatment淬火 hardening, quenching退火 annealing回火 tempering正火 normalizing车床 lathe龙门刨床 planer牛头刨床 shaper插床 vertical shaper铣床 milling machine钻床 drilling machine磨床 grinder, grinding machine 外圆磨床 external grinder内圆磨床 internal grinder平面磨床 surface grinder镗床 boring machine拉床 broacher床头箱 head stock (gear box) 卡盘，夹盘 chuck尾座 tail stock走刀箱 tool carrier模具 die, mold气锤 pneumatic hammer压床 press刀具 cutter车刀，刨刀 bite铣刀，绞刀 fraise钻头 bite磨轮，砂轮 grinding wheel夹具 fixture, jig汽车 automobile拖拉机 tractor铁路机车 locomotive有轨电车 tram无轨电车 trolley军用车辆 military vehicle蒸汽机 steam engine煤气机 gas engine汽油机 gasoline engine国民经济 national economy国内生产总值 (GDP) Gross Domestic Production 全拆散 (CKD) Completely Knock Down半拆散 (SKD) Semi-Knock Down改革开放 reform and opening技术引进 technical import国产化 localization支柱产业 pillar estate轿车 car客车 bus, coach货车 truck, lorry公路用车 road vehicle非公路用车 off-road vehicle发动机 engine机体 engine body曲柄连杆机构 crank-connecting rod mechanism 配气机构 valve timing mechanism供给系 fuel supply system冷却系 cooling system润滑系 lubricating system点火系 ignition system起动系 starting system底盘 chassis传动系 power train离合器 clutch变速器 gear box传动轴 propeller shaft驱动桥 drive axle行驶系 running gear车架 frame悬架 suspension前轴 front axle桥壳 axle housing车轮 wheel转向系 steering system转向盘 steering wheel转向器 steering gear转向传动装置 steering linkage助力装置 power assisting device制动系 braking system控制装置 control device供能装置 power supply device传动装置 transfer device制动器 brake车身 body车前板制件 front end panels车身壳体 body shell车门 door车窗 window附属装置 auxiliary device货箱 carrying platform发动机前置后轮驱动 (FR) front engine rear drive 发动机前置前轮驱动 (FF) front engine front drive 发动机后置后轮驱动 (RR) rear engine rear drive发动机中置后轮驱动 (MR) midship engine rear drive 全轮驱动 (nWD) all wheel drive驱动力 tractive force阻力 resistance滚动阻力 rolling resistance空气阻力 air resistance, drag上坡阻力 gradient resistance附着作用 adhesion附着力 adhesive force附着系数 coefficient of adhesion第一章发动机工作原理二冲程发动机 two stroke engine四冲程发动机 four stroke engine水冷发动机 water cooled engine风冷发动机 air cooled engine上止点 (UDP) upper dead point下止点 (LDP) lower dead point活塞行程 stroke汽缸直径 bore工作容积 working volume排量 swept volume, displacement进气行程 intake stroke压缩行程 compression stroke压缩比 compression ratio做功行程 working stroke爆燃，敲缸 detonation, knock 排气行程 exhaust stroke示功图 indicating diagram汽缸体 cylinder block汽缸盖 cylinder head油底壳 oil sump活塞 piston连杆 connecting rod曲轴 crankshaft飞轮 flywheel进气门 intake valve排气门 exhaust valve挺柱 tappet推杆 push rod摇臂 rocker凸轮轴 camshaft正时齿轮 timing gear燃油箱 fuel tank燃油泵 fuel pump汽油滤清器 gasoline filter 化油器 carburetor空气滤清器 air cleaner进气管 intake manifold排气管 exhaust manifold火花塞 spark plug点火线圈 ignition coil断电器 breaker蓄电池 storage battery发电机 generator水泵 water pump散热器 radiator风扇 fan放水阀 drain valve水套 water jacket分水管 distributive pipe机油泵 oil pump集滤器 suction filter限压阀 relief valve润滑油道 oil passage机油滤清器 oil filter机油冷却器 oil cooler起动机 starting motor有效功率 effective power有效转矩 effective torque燃油消耗率 specific fuel consumption发动机转速特性 engine speed characteristic节气门开度 throttle percentage部分特性 partial characteristic外特性 outer characteristic第二章曲柄连杆机构汽缸套 cylinder sleeve, cylinder liner发动机支承 engine mounting活塞顶 piston top活塞头部 piston head活塞裙 piston skirt开槽 slot活塞环 piston ring气环 compression ring油环 oil ring环槽 groove活塞销 piston pin主轴承 main bearing主轴承盖 main bearing cap主轴瓦 main shell连杆轴承 big end bearing连杆盖 big end cap起动爪 cranking claw带轮 pulley平衡重 counter weight发火顺序 firing order扭振减振器 torsional vibration damper第三章配气机构顶置气门 (OHV) Over Head Valve顶置凸轮轴 (OHC) Over Head Camshaft单顶置凸轮轴 (SOHC) Single Over Head Camshaft 双顶置凸轮轴 (DOHC) Dual Over Head Camshaft 多气门发动机 multi-valve engine气门间隙 valve clearance配气相位 timing phase气门杆 valve stem气门座 valve seat气门导管 valve guide气门弹簧 valve spring第四章汽油机供给系可燃混合气 combustion mixture消声器 silencer, muffler汽油 gasoline, petrol分馏 distil蒸发性 evaporating property热值 heat value抗爆性 anti-knock property辛烷值 (RON) Research Octane Number过量空气系数 coefficient of excessive air 理论混合气 theoretical mixture稀混合气 thin mixture浓混合气 thick mixture主供油系统 main supply system怠速系统 idle system加浓系统 thickening system加速系统 accelerating system浮子 float浮子室 float chamber针阀 needle valve量孔 metering jet阻风门 choke滤芯 filter cartridge沉淀杯 sediment cup泵膜 pump diaphragm油浴式 oil bath type石棉垫 a**estos pad预热 pre-heating汽油直接喷射 gasoline direct injection电控 electronic control多点喷射 muti-point injection单点喷射 single point injection电路控制 circuit control分电器信号 distributor signal空气流量信号 airflow signal冷却水温信号 water temperature signal第五章柴油机供给系输油泵 transfer pump喷油泵 fuel injection pump高压油管 high pressure fuel pipe发火性 ignition property黏度 viscosity凝点 condensing point备燃期 pri-combustion period速燃期 rapid combustion period缓燃期 slow combustion period燃烧室 combustion chamber统一燃烧室 united chamber球形燃烧室 ball shape chamber涡流室 turbulence chamber预燃室 pri-combustion chamber喷油器 injector精密偶件 precise couple柱塞 plunger出油阀 delivery valve调速器 governor两速调速器 two speed governor全速调速器 full speed governor定速调速器 fixed speed governor综合调速器 combined governor气动调速器 pneumatic governor机械离心式调速器 mechanical centrifugal governor 复合式调速器 complex governor喷油提前角调节装置 advancer飞块 flyweight联轴节 coupling粗滤清器 primary filter细滤清器 secondary filter涡轮增压器 turbocharger中间冷却器 intermediate cooler第七章冷却系节温器 thermostat防冻液 anti-freezing liquid补偿水桶 compensation reservoirV-带 V belt百叶窗 shutter大循环 big circulation小循环 small circulation散热翅片 fins第八章润滑系润滑剂 lubricant压力润滑 pressure lubrication飞溅润滑 splash lubrication润滑脂 grease机油压力传感器 oil pressure sensor油封 oil seal旁通阀 bypass valve机油散热器 oil cooler机油尺 dip stick加机油口 oil filler曲轴箱通风 crankcase ventilation第九章点火系一次绕组 primary winding二次绕组 secondary winding热敏电阻 heat sensitive resistance点火提前 ignition advance分电器 distributor活动触点 moving contact固定触点 fixed contact分火头 distributor rotor arm电容器 condenser点火提前装置 ignition advancer离心式点火提前装置 centrifugal ignition advancer 真空式点火提前装置 vacuum ignition advancer辛烷值校正器 octane number rectifier中心电极 central electrode侧电极 side electrode瓷绝缘体 ceramic insulator跳火间隙 spark gap半导体点火系 semi-conductor ignition system晶体管 transistor二极管 diode三极管 triode无触点点火系 non-contact ignition system霍尔效应 Hall effect正极板 anode负极板 cathode隔板 separator电解液 electrolyte蓄电池格 battery cell接线柱 terminal电缆 cable硅整流交流发电机silicon rectified A.C. motor转子 rotor定子 stator电刷 brush风扇叶轮 fan blade电压调节器 voltage regulator第十章起动系手摇起动 cranking电热塞 electric heater plug串激直流发电机 serial wound D.C. motor起动齿圈 starter ring电磁操纵机构 electro-magnetic control第十一章新型发动机三角活塞 triangular piston转子发动机 rotary engine自转 rotary motion, rotation公转 orbit motion轨迹 trajectory齿轮 gear齿圈 ring gear往复零件 reciprocal parts动平衡 dynamic balance燃气涡轮发动机 gas turbine第十二章汽车传动系机械式传动系 mechanical transmission液力机械式传动系 hydro-mechanical transmission静液式传动系 static-hydraulic transmission电力式传动系 electrical transmission自动式传动系 automatic transmission减速 reduction可变速比 variable ratios有级变速 definite ratios无级变速 indefinite ratios无级变速器(CVT) Continuously Variable Transmission 一般布置 general layout发动机横置 lateral engine positioning分动器 transfer case, transfer box第十三章离合器接合柔和 smooth engagement分离彻底 thorough separation过载 overload摩擦表面 friction surface摩擦衬片 friction liner毂 hub主动部分 driving part从动部分 driven part花键 spline压盘 pressure plate离合器盖 cover plate分离杠杆 release lever分离套筒 release sleeve分离轴承 release bearing主缸 master cylinder工作缸 working cylinder分离叉 release fork间隙调整 clearance adjustment打滑 slip踏板 pedal踏板自由行程 pedal free stroke踏板工作行程 pedal working stroke铆钉，铆接 rivet双片离合器 dual disc clutch中央弹簧离合器 central spring clutch膜片弹簧离合器 diaphragm spring clutch 非线性 non-linear第十四章变速器与分动器输入轴（第一轴）input shaft, drive shaft 输出轴（第二轴）output shaft, main shaft 中间轴 counter shaft倒挡轴 reverse gear shaft常啮合 constant mesh低速挡 low gear高速挡 high gear最高速挡 top gear空挡 neutral gear一挡 the first gear二挡 the second gear三挡 the third gear倒挡 reverse gear直接挡 direct gear超速挡 overdrive动力输出 power take-off换挡 shift啮合套 sliding sleeve同步器 synchronizer同步锥面 synchro cone变速杆 shifting lever手柄 handle球铰链 ball joint换挡拨叉 shifting fork自锁 self-lock互锁 inter-lock变速驱动桥 transaxle加力挡 low gear第十五章液力机械传动液力偶合器 hydraulic coupling泵轮 impeller涡轮 turbine叶片 blade液力变矩器 torque converter导轮 stator行星齿轮系 planetary gear system太阳轮 sun gear行星轮 planet pinion行星架 planet carrier齿圈 ring gear第十六章传动轴万向节 universal joint, U-joint十字轴式万向节Cardan type U-joint叉子 yoke, fork十字轴 spider, center cross滚针轴承 needle bearing滑脂嘴（油嘴）lubricating fitting, nipple等角速 constant angular velocity双联式万向节 dual Cardan type U-joint球叉式万向节 Weiss type U-joint球笼式万向节 Rzeppa type U-joint星形套 inner race housing球形壳 outer race shell保持架，球笼 retainer, ball cage挠性万向节 flexible U-joint无缝钢管 seamless steel tube第十七章驱动桥主减速器 final drive主动（小）齿轮 drive pinion从动（大）齿轮 ring gear伞齿轮 bevel gear双曲面齿轮 hypoid gear单级减速 single reduction双级减速 double reduction贯通式主减速器 penetrable final drive双速主减速器 double gear (speed) final drive 轮边减速器 wheel reduction差速器 differential半轴齿轮 differential side gear差速锁 differential lock轴间差速器 inter-axle differential lock托森差速器 torque sensitive differential。

. 渐开线花键 involute spline精度等级 precision class未注公差 undeclared tolerance未注倒角 undeclared chamfer调质 thermal refining端口 port chamfer模数 modulus齿形角 tooth profile angle变位系数 stand-off error齿圈径向跳动 geared ring radial runout公法线长度及偏差 common normal跨齿数 spanned tooth count高频淬火 high-frequency quenching配对齿轮 mating gear螺旋角 spiral angle压力角 pressure angle螺旋升角 lead angle图号 figure number齿厚 tooth thickness螺旋线 helix蜗杆 worm齿轮 gear齿轴 gear shaft转子轴 rotor shaft.齿轮基本术语齿轮Toothed gear；Gear 齿面Tooth flank长幅内摆线Prolate hypocycloid齿轮副Gear pair右侧齿面Right flank短幅内摆线Curtate hypocycloid平行轴齿轮副Gear pair with parallel axes左侧齿面Left flank渐开线Involute；Involute to a circle相交轴齿轮副Gear pair with intersecting axes 同侧齿面Corresponding flank延伸渐开线Prolate involute齿轮系Train of gears异侧齿面Opposite flank缩短渐开线Curtate involute行星齿轮系Planetary gear train工作齿面Working flank球面渐开线Spherical involute齿轮传动Gear drive；Gear transmission 非工作齿面Non-working flank渐开螺旋面Involute helicoid配对齿轮Mating gears.相啮齿面Mating flank阿基米德螺旋面Screw helicoid小齿轮Pinion共轭齿面Conjugate flank球面渐开螺旋面Spherical involute helicoid 大齿轮Wheel；Gear可用齿面Usable flank圆环面Toroid主动齿轮Driving gear有效齿面Active flank圆环面的母圈Generant of the toroit从动齿轮Driven gear上齿面Addendum flank圆环面的中性圈Middle circle of the toroid 行星齿轮Planet gear下齿面Dedendum flank圆环面的中间平面Middle-plane of the toroid 行星架Planet carrier齿根过渡曲面Fillet圆环面的内圈Inner circle of the toroid 太阳轮Sun gear齿顶Crest；Top land啮合干涉Meshing interference内齿圈Ring gear；Annulus gear 槽底Bottom land切齿干涉Cutter interference外齿轮External gear齿廓Tooth profile齿廓修型Profile modification；Profile correction内齿轮Internal gear端面齿廓Transverse profile修缘Tip relief中心距Centre distance法向齿廓Normal profile修根Root relief轴交角Shaft angle轴向齿廓Axial profile齿向修形Axial modification；Longitudinal correction 连心线Line of centres.背锥齿廓Back cone tooth profile齿端修薄End relief减速齿轮副Speed reducing gear pair 齿线Tooth trace鼓形修整Crowning增速齿轮副Speed increasing gear pair 齿棱Tip；Tooth tip鼓形齿Crowned teeth齿数比Gear ratio模数Module挖根Undercut传动比Transmission ratio端面模数Transverse module瞬时轴Instantaneous axis轴平面Axial plane法向模数Normal module瞬时接触点Point of contact基准平面Datum plane轴向模数Axial module瞬时接触线Line of contact 节平面Pitch plane径节Diametral pitch端面啮合线Transverse path ofPineneedle 050328contact端平面Transverse plane齿数Number of teech啮合曲面Surface of action法平面Normal plane当量齿数Virtual number of teeth啮合平面Plane of action分度曲面Reference surface头数Number of starts；Number of threads 啮合区域Zone of action节曲面Pitch surface螺旋线Helix；Circular helix总作用弧Total arc of transmission齿顶曲面Tip surface圆锥螺旋线Conical spiral端面作用弧Transverse arc of transmission齿根曲面Root surface.螺旋角Helix angle；Spiral angle纵向作用弧Overlap arc基本齿廓Basic tooth profile导程Lead总作用角Total angle of transmission基本齿条Basic rack导程角Lead angle端面作用角Transverse angle of transmission 产形齿条Counterpart rack阿基米德螺旋线Archimedes spiral纵向作用角Overlap angle产形齿轮Generating gear of a gear外摆线Epicycloid总重合度Total contact ratio产形齿面Generating flank长幅外摆线Prolate epoicycloid端面重合度Transverse ratio基准线Datum line短幅外摆线Curtate epoicycloid纵向重合度Overlap ratio轮齿Gear teeth；Tooth摆线Cycloid标准齿轮Standard gears齿槽Tooth space长幅摆线Prolate cycloid非变位齿轮X-gero gear右旋齿Right-hand teeth短幅摆线Curtate cycloid标准中心距Referencr centre distance左旋齿Left-hand teeth内摆线Hypocycloid名义中心距Nominal centre distance变位齿轮Gears with addendum modification；X-gears直齿轮Spur gear分度圆柱面Reference cylinder高度变位圆柱齿轮副X-gear pair with reference centre distance 斜齿轮Helical gear；Single-helical gear节圆柱面Pitch cylinder角度变位圆柱齿轮副X-gear pair with modified centre distance.直齿条Spur rack基圆柱面Basic cylinder高度变位锥齿轮副X-gear pair without shaft angle modification 斜齿条Helical rack齿顶圆柱面Tip cylinder角度变位圆柱齿轮副X-gear pair with shaft angle modification人字齿轮Double-helical gear齿根圆柱面Root cylinder变位系数Modification coefficient渐开线齿轮Involute cylindrical gear节点Pitch point变位量Addendum摆线齿轮Cycloidal gear节线Pitch linePineneedle 050328modification径向变位系数Addendum modification coefficient圆弧齿轮Circular-arc gear；W-N gear分度圆Reference circle中心距变位系数Centre distance modification coefficient双圆弧齿轮Double-circular-arc gear 节圆Pitch circle圆柱齿轮Cylindrical gear假想曲面Imaginary surfance基圆Basic circle顶圆Tip circle任意点法向压力角Normal pressure angle at a point定位面Locating face根圆Root circle任意点端面压力角Transverse pressure angle at a point 外锥距Outer cone distance齿距Pitch啮合角Working pressure angle内锥距Inner cone distance齿距角Angular pitch顶隙Bottom clearance中点锥距Mean cone distance公法线长度Base tangent length圆周侧隙Circumferential blacklash背锥距Back cone distance分度圆直径Reference diameter.法向侧隙Normal blacklash安装距Locating distance节圆直径Pitch diameter径向侧隙Radial blacklash轮冠距Tip distance；crown to back 基圆直径Base diameter锥齿轮Bevel gear冠顶距Apex to crown顶圆直径Tip diameter锥齿轮副Bevel gear pair偏置距Offset根圆直径Root diameter准双曲面齿轮副Hypoid gear pair齿线偏移量Offset of tooth trace齿根圆角半径Fillet radius准双曲面齿轮Hypoid gear分锥角Reference cone angle齿高Tooth depth冠轮Crown gear节锥角Pitch cone angle 工作高度Working depth端面齿轮Contrate gear顶锥角Tip angle齿顶高Addendum直齿锥齿轮Straight bevel gear根锥角Root angle齿根高Dedendum斜齿锥齿轮Skew bevel gear；Helical bevel gear背锥角Back cone angle弦齿高Chordal height曲面齿锥齿轮Curved tooth bevel gear 齿顶角Addendum angel固定弦齿高Constant chord height 弧齿锥齿轮Spiral bevel gear齿根角Dedendum angle齿宽Facewidth摆线齿锥齿轮Enicycloid bevel gear任意点压力角Pressure angle at a point 有效齿宽Effective facewidth零度齿锥齿轮.Zerot bevel gear任意点螺旋角Spiral angle at a point端面齿厚Transverse tooth thickness圆柱齿轮端面齿轮副Contrate gear pair中点螺旋角Mean spiral angle法向齿厚Normal tooth thickness锥齿轮的当量圆柱齿轮Virtual cylindrical gear of bevel gear大端螺旋角Outer spiral angle端面基圆齿厚Transverse base thickness8字啮合锥齿轮Octoid gear小端螺旋角Inner spiral angle法向基圆齿厚Normal base thickness圆柱齿弧锥齿轮Spiral bevel gear with circle arc tooth profile 蜗杆WormPineneedle 050328端面弦齿厚Transverse chordal tooth thickness分度圆锥面Reference cone蜗轮Worm wheel固定弦齿厚Constant chord节圆锥面Pitch cone蜗杆副Worm gear pair 端面齿顶厚Crest width齿顶圆锥面Face cone；tip cone圆柱蜗杆Cylindrical worm法向齿顶厚Normal crest width齿根圆锥面Root cone圆柱蜗杆副Cylindrical worm pair端面齿槽宽Transverse spacewidth背锥面Back cone环面蜗杆Enveloping worm法向齿槽宽Normal spacewidth前锥面Front cone环面蜗杆副Enveloping worm pair齿厚半角Tooth thickness half angle中锥面Middle cone阿基米德蜗杆Straight sided axial worm；ZA-worm 槽宽半角Spacewidth half angle分锥顶点Reference cone apex渐开线蜗杆Involute helicoid worm；ZI-worm压力角Pressure angle轴线交点Crossing point of axes.法向直廓蜗杆Straight sided normal worm；ZN-worm齿形角Nominal pressure angle公共锥顶Common apex锥面包络圆柱蜗杆Milled helicoid worm；ZK-worm圆弧圆柱蜗杆Arc-contact worm；hollow flank worm；ZC-worm齿根圆环面Root tosoid椭圆齿轮Elliptical gear直廓环面蜗杆Enveloping worm with straight line grneratrix；TA worm 咽喉面Gorge非圆齿轮副Non-circular gear pair平面蜗杆Planar worm wheel；P-worm wheel喉平面Gorge plane圆柱针轮副Cylindsical lantern pinion and wheel平面包络环面蜗杆Planar double enveloping worm；TP-worm喉圆Gorge circle针轮Cylindsical tan tein gear ；pin-wheel平面二次包络蜗杆Planar double-enveloping worm wheel；TP-worm wheel分度圆蜗旋线Reference helix谐波齿轮副Harmoric gear drive锥面包络环面蜗杆Toroid enveloping worm wheel；TK-worm wheel螺纹Thread波发生器Wave generator渐开线包络环面蜗杆Toroid enveloping worm hich involute holicoid generatrix；TI-worm蜗杆齿宽Worm facewidth柔性齿轮Flexspine锥蜗杆Spiroid蜗轮齿宽Worm wheel facewidth刚性齿轮Circular spline锥蜗轮Spiroid gear直径系数Diametral quotient非圆齿轮Non-circular gearPineneedle 050328锥蜗杆副Spiroid gear pair咽喉半径Gorge radius分度圆环面Reference tosoid中平面Mid-plane齿宽角Width angle。

齿轮中英文对照齿轮基本术语中英文对照齿轮Toothed gear；Gear齿轮副Gear pair平行轴齿轮副Gear pair with parallel axes相交轴齿轮副Gear pair with intersecting axes 齿轮系Train of gears行星齿轮系Planetary gear train齿轮传动Gear drive；Gear transmission配对齿轮Mating gears小齿轮Pinion大齿轮Wheel；Gear主动齿轮Driving gear从动齿轮Driven gear行星齿轮Planet gear行星架Planet carrier太阳轮Sun gear内齿圈Ring gear；Annulus gear外齿轮External gear内齿轮Internal gear中心距Centre distance轴交角Shaft angle连心线Line of centres减速齿轮副Speed reducing gear pair增速齿轮副Speed increasing gear pair齿数比Gear ratio传动比Transmission ratio轴平面Axial plane基准平面Datum plane节平面Pitch plane端平面Transverse plane法平面Normal plane分度曲面Reference surface节曲面Pitch surface齿顶曲面Tip surface齿根曲面Root surface基本齿廓Basic tooth profile基本齿条Basic rack产形齿条Counterpart rack产形齿轮Generating gear of a gear产形齿面Generating flank基准线Datum line轮齿Gear teeth；T ooth齿槽Tooth space右旋齿Right-hand teeth左旋齿Left-hand teeth变位齿轮Gears with addendum modification；X-gears高度变位圆柱齿轮副X-gear pair with reference centre distance 角度变位圆柱齿轮副X-gear pair with modified centre distance 高度变位锥齿轮副X-gear pair without shaft angle modification 角度变位圆柱齿轮副X-gear pair with shaft angle modification 变位系数Modification coefficient变位量Addendum modification径向变位系数Addendum modification coefficient中心距变位系数Centre distance modification coefficient圆柱齿轮Cylindrical gear顶圆Tip circle根圆Root circle齿距Pitch齿距角Angular pitch公法线长度Base tangent length分度圆直径Reference diameter节圆直径Pitch diameter基圆直径Base diameter顶圆直径Tip diameter根圆直径Root diameter齿根圆角半径Fillet radius齿高Tooth depth工作高度Working depth齿顶高Addendum齿根高Dedendum弦齿高Chordal height固定弦齿高Constant chord height齿宽Facewidth有效齿宽Effective facewidth端面齿厚Transverse tooth thickness法向齿厚Normal tooth thickness端面基圆齿厚Transverse base thickness法向基圆齿厚Normal base thickness端面弦齿厚Transverse chordal tooth thickness 固定弦齿厚Constant chord端面齿顶厚Crest width法向齿顶厚Normal crest width端面齿槽宽Transverse spacewidth法向齿槽宽Normal spacewidth齿厚半角Tooth thickness half angle槽宽半角Spacewidth half angle压力角Pressure angle齿形角Nominal pressure angle圆弧圆柱蜗杆Arc-contact worm；hollow flank worm；ZC-worm直廓环面蜗杆Enveloping worm with straight line grneratrix；TA worm平面蜗杆Planar worm wheel；P-worm wheel平面包络环面蜗杆Planar double enveloping worm；TP-worm 平面二次包络蜗杆Planar double-enveloping worm wheel；TP-worm wheel锥面包络环面蜗杆T oroid enveloping worm wheel；TK-worm wheel渐开线包络环面蜗杆Toroid enveloping worm hich involute holicoidgeneratrix；TI-worm锥蜗杆Spiroid锥蜗轮Spiroid gear锥蜗杆副Spiroid gear pair中平面Mid-plane长幅内摆线Prolate hypocycloid短幅内摆线Curtate hypocycloid渐开线Involute；Involute to a circle延伸渐开线Prolate involute缩短渐开线Curtate involute球面渐开线Spherical involute渐开螺旋面Involute helicoid阿基米德螺旋面Screw helicoid球面渐开螺旋面Spherical involute helicoid圆环面T oroid圆环面的母圈Generant of the toroit圆环面的中性圈Middle circle of the toroid圆环面的中间平面Middle-plane of the toroid圆环面的内圈Inner circle of the toroid啮合干涉Meshing interference切齿干涉Cutter interference齿廓修型Profile modification；Profile correction修缘Tip relief修根Root relief齿向修形Axial modification；Longitudinal correction齿端修薄End relief鼓形修整Crowning鼓形齿Crowned teeth挖根Undercut瞬时轴Instantaneous axis瞬时接触点Point of contact瞬时接触线Line of contact端面啮合线Transverse path of contact啮合曲面Surface of action啮合平面Plane of action啮合区域Zone of action总作用弧Total arc of transmission端面作用弧Transverse arc of transmission纵向作用弧Overlap arc总作用角Total angle of transmission端面作用角Transverse angle of transmission 纵向作用角Overlap angle总重合度Total contact ratio端面重合度Transverse ratio纵向重合度Overlap ratio标准齿轮Standard gears非变位齿轮X-gero gear标准中心距Referencrcentre distance 名义中心距Nominal centre distance 分度圆柱面Reference cylinder节圆柱面Pitch cylinder基圆柱面Basic cylinder齿顶圆柱面Tip cylinder齿根圆柱面Root cylinder节点Pitch point节线Pitch line分度圆Reference circle节圆Pitch circle基圆Basic circle定位面Locating face外锥距Outer cone distance内锥距Inner cone distance中点锥距Mean cone distance背锥距Back cone distance安装距Locating distance轮冠距Tip distance；crown to back 冠顶距Apex to crown偏置距Offset齿线偏移量Offset of tooth trace分锥角Reference cone angle节锥角Pitch cone angle顶锥角Tip angle根锥角Root angle背锥角Back cone angle齿顶角Addendum angel齿根角Dedendum angle任意点压力角Pressure angle at a point任意点螺旋角Spiral angle at a point中点螺旋角Mean spiral angle大端螺旋角Outer spiral angle小端螺旋角Inner spiral angle蜗杆Worm蜗轮Worm wheel蜗杆副Worm gear pair圆柱蜗杆Cylindrical worm圆柱蜗杆副Cylindrical worm pair环面蜗杆Enveloping worm环面蜗杆副Enveloping worm pair阿基米德蜗杆Straight sided axial worm；ZA-worm渐开线蜗杆Involute helicoid worm；ZI-worm法向直廓蜗杆Straight sided normal worm；ZN-worm锥面包络圆柱蜗杆Milled helicoid worm；ZK-worm椭圆齿轮Elliptical gear非圆齿轮副Non-circular gear pair圆柱针轮副Cylindsical lantern pinion and wheel针轮Cylindsical tan tein gear ；pin-wheel谐波齿轮副Harmoric gear drive波发生器Wave generator柔性齿轮Flexspine刚性齿轮Circular spline非圆齿轮Non-circular gear分度圆环面Reference tosoidinvolute spline data：渐开线花键参数flat root side fit ：平齿根齿侧定心三维|cad|机械汽车技术|catia|pro/e|ug|inventor|solidedge|soli dworks|caxa# u5 f9 E4 {6 p1 `, V; B2 |/ ^pith（应为pitch）：径节 14/32number of teeth：齿数 195 d, b. w( @6 }# f9 [pressure angle ：压力角 30base cicledia (ref) ：基圆直径/doc/bb7992786.html,( K. M H' r! J$ \* S$ ]2 _ cicular space width：分度圆齿槽宽min effective：最小作用齿槽宽 0.0982. n! B6 [) W3 {2 K) u3 o6 b% K$ ]) hmax effective(ref) ：最大作用齿槽宽 0.0997min actual(ref)：最小实际齿槽宽 0.0992& q. Z" s7 I$ N& |" `" omax actual ：最大实际齿槽宽0.1007三维,cad,机械技术汽车,catia,pr o/e,ug,i nventor,solidedge,solidw orks,ca xa,时空镇江, {9 e# I1 ]( I3 y+ G& A# Mmax mesaurement between two 0.0900 dia pins：在量棒直径0.09之间的量棒距最大值1.0878 involute profile error ：齿形误差+0.0003 -0.0005total index error max ：相当于齿距累积误差0.0015mat parallelism error：齿向误差 0.0005三维|cad|机械汽车技术|catia|pro/e|ug|inventor|soli dedge|solidworks|ca xa. n E% H0 x! r8 u' F/doc/bb7992786.html,3 J9 c" ]4 O) E" d- k PITCH DIA. (STAND ＆MESHING)分度圆直径CIRCULAR PITCH (NORM) 基节FORM DIAMETER 展成圆直径MAX. ACTUAL 最大实际齿厚MIN. LEFECTIVE 最小作用齿厚MEASUREMENT BETWEEN PINS 跨棒距（就是M值）FORM DIAMETER 展成圆直径,一般来说，是叫渐开线起始圆直径或终止圆直径比较好。