MY-MS 6P(配MY-GB9)接线使用说明

1．目的：用于工务交车前对MP U和XD R板进行调试。

2．对应作业：1-1对M PU电梯调试接线连接：1）.对M PUG B2(A2)版电梯调试时（以及A2前版本），接线情况如下：连接顺序连接线端口MPUGB2端口SANN端口第一步J1 J1第二步LMC LMC第三步MUA MUA2）对应MPU GB2(A3)版电梯调试时，接线情况如下（无需接MUA）：连接顺序连接线端口MPUGB2端口SANN端口第一步J1 J1第二步LMC LMC1-2对应M PU调试步骤1).将SA NN工作模式设置为1.MP U模式，可通过上下键调整。

2).按EN TE R键，等待连接和权限检测，交车前，并且连线正确将进入MPU调试模式。

3).S ANN显示电梯目前状态，并且可进行调试。

4).调试结束将连接线从M PU板拔出。

2-1对XD R调试接线连接：1）对XD R（B1版及以前版本）门机调试接线连接：连接顺序连接线端口XDR端口SANN端口第一步将XDR电源断掉第二步将XDR之5VRE端口对应的编码器接线拔下第三步J1 J1第四步LMC LMC第五步XDR 5VRE对应的编码器接口第六步5VRE 5VRE第七步接通XDR电源，将XDR板拨码开关调为OFF 2）对XD R（B2版）门机调试接线连接：（无插拔RE线及电源线）：连接顺序连接线端口XDR端口SANN端口第一步J1 J1第二步LMC LMC第三步将XDR板拨码开关调为OFF2－2对应XD R门机调试步骤操作模式当前状态及显示按键XDR动作按键后显示状态磁极测定1.Me gTe st ENTE R MegT est.EN TER MegT est.EN TER ESC 1.Me gTe st MegT est.EN TER ENTE R磁极测定MegT est.TE STI NGMegT est.TE STI NG测定正确MegT est.OK测定失败MegT est.FA ILE MegT est.TE STI NG ESC终止磁极测定MegT est.EN TER MegT est.OK等待12S后响应不通讯MegT est.wa it…MegT est.FA ILEESC MegT est.EN TER MegT est.wa it…行程测定2.DisTest ENTER DisTest.ENTER DisTest.ENTER ESC 2.DisTest DisTest.ENTER ENTER 行程测定DisTest.TESTINGDisTest.TESTING测定正确DisTest.OK测定失败DisTest.FAILE结束返回操作DisTest.wait…DisTest.TESTING ESC 终止行程测定DisTest.ENTER DisTest.OK 等待12S响应其它测试根据操作确定DisTest.FAILE故障码查看及清除3.ER CODE ENTER 传回故障信息ER CODE.EX（X为故障码）ER CODE.EX ENTER 清故障码ER CODE.EG（无故障）ER CODE.EX ESC 3.ER CODEXDR故障码对应关系故障码故障描述E0 磁极未测定运行E1 上电运行磁极位置测定失败E2 磁极偏差过大E3 运转状态错误E4 皮带断裂或未接妥E5 复位开关失效(行程测定) E6 Encoder AB断线或未接妥E7 马达或Encoder配错线E8 Encoder Z 断线E9 EEPROM读写错误EA 过电流EB 低电压故障(<85V)EC 通讯故障ED 故障预留EE 故障预留EF 故障预留EG 无故障3．SANN故障处理办法将连接线拔下，重新进行连接，确认连接线LM C端口与对应板连接是否紧密，如连接不成功，建议更换连接线。

IPM910B系列单相数字式智能电表用户说明书IPM910B-MIPM910B-VIPM910B-IIPM910B-M-PLUS危险和警告本设备只能由专业人士进行安装，对于因不遵守本手册的说明所引起的故障，厂家将不承担任何责任。

触电、燃烧或爆炸的危险⏹设备只能由取得资格的工作人员才能进行安装和维护。

⏹对设备进行任何操作前，应隔离电压输入和电源供应，并且短路所有电流互感器的二次绕组。

⏹要用一个合适的电压检测设备来确认电压已切断。

⏹在将设备通电前，应将所有的机械部件，门和盖子恢复原位。

⏹设备在使用中应提供正确的额定电压。

不注意这些预防措施可能会引起严重伤害。

本说明书版权属深圳市西研科技有限公司所有，未经书面许可，不得复制，传播或使用本文件及其内容，违犯者将要对损坏负责。

深圳市西研科技有限公司保留所有版权。

我们已经检查了本手册关于描述硬件和软件保持一致的内容。

由于不可能完全消除差错，所以我们不能保证完全的一致。

本手册中的数据将定期审核，并在新一版的文件中做必要的修改，欢迎提出修改建议。

以后版本中的变动不再另行通知。

目录1.装置简介 (1)1.1.概述 (1)1.2.基本功能一览表 (1)2.额定参数 (2)3.性能指标 (2)4.结构外观与安装 (3)4.1.外观 (3)4.2.安装步骤 (4)4.3.结构尺寸 (4)4.4.安装注意事项 (4)4.5.端子图 (4)5.典型接线图 (6)5.1.电压电流输入接线 (10)5.2.通信接线 (11)5.3.DI的连接 (11)6.操作说明 (12)6.1.按键说明 (12)6.2.测量显示 (13)7.参数设置 (14)8.售后服务承诺 (16)8.1.质量保证 (16)8.2.装置升级 (16)8.3.质保限制 (16)9.通信协议 (17)1. 装置简介1.1. 概述IPM910B系列单相数字式智能电表，以工业级微处理器为核心，处理速度高，具有很高的性价比。

FV_BMW_6Pin 接口盒安装使用说明产品型号: FV_BMW_6Pin ，ver:20120416本接口盒向BMW F20/F30 的显示屏(采用6P 的圆接头的宝马各个系列的显示屏)，提供RGB, 2路AV,以及倒车影像插入功能，在原车的显示屏上显示 导航/倒车影像 或DVD/数字电视，iPod 图像，并具有以下优点:✓ 插头采用BMW 专用接头，不需要打开屏幕。

非常容易安装。

并且没有损伤原车的风险。

并且利用原车的旋钮可以切换和操控后加的设备。

✓ 高清晰度的图像处理器能够在原车的屏幕上显示后加的导航，倒车，以及数字电视的信息。

✓ 可以显示倒车的轨迹线.并且能够将原车的倒车雷达图像和后视图像混合显示.[原车的雷达图在屏幕右边] ✓ 通过CAN 线接入，自动产生倒车信号,通道切换信号和轨迹线信号。

F30后加导航显示 F20后加倒车+后加轨迹+原车雷达显示注意 ：● F20，F30出现在2012的宝马1，3，5，7等车型上，特点是4P 的信号线的旁边就是2P 的电源线，并且整个显示屏只有一个接头连接。

● 之前款（2009~2012）采用一个4P 的信号插头，以及另外一个电源插头，此车型采用京乐驰的FV-BMW-CIC，或者FV-BMW-CIC2接口盒。

● 在2009年之前的BMW，采用10P 方接头[BMW 的M-ASK 系统，CCC 系统]，此车型请采用FV-BMW-CCC 接口合。

1．DIP 开关设定DIP 拨下（=到ON） 拨上（=到OFF） 1 RGB 输入打开 RGB 输入关闭 2,3 AV1/2 打开AV1/2 关闭4 RGB 输入设定：输入VGA 的RGB 高清晰度图像 图像分辨率：640X480。

RGB 输入设定：输入NTSC 的RGB 高清晰度图像图像分辨率：320X240。

5 倒车时候[绿色线变成12V]：切换到AV4倒车时候切换到原车画面 6拨下一次进行进行红外代码学习 [当OSD 将AV1设定到PROG 的时候]，拨下5次进行触摸屏校准。

About your phoneSetting up your phoneYour phone already has a SIM card installed.Charge the PhoneBefore turning on your phone, charge it fully.Your phone comes with an Adaptive Fast Charging charger and a USB cable. Plug the smaller end of the cable into the USB/charger port on your phone and the larger end into the charger. Then plug the charger into an electrical outlet to charge the phone.NOTE: Devices and software are constantly evolving—the screen images and icons you see here are for reference only.Samsung and Galaxy S are trademarks of SamsungElectronics Co., Ltd. Android, Google, the Google logo and Google Play are trademarks of Google Inc. Screen imagessimulated. Appearance of device may vary.Volume Buttons+-Recent Apps HeadsetJackHomeBackSIM/microSDCard TrayFront CameraEdge ScreenEdge ScreenRear CameraUSB/Charger PortWARNING: Use only Samsung-approved charging devices. Samsung accessories are designed to maximize battery life. Using other accessories may invalidate your warranty and may cause damage.Optional: Insert the microSD card.1. With the screen facing up, insert the tool thatcame with your phone into the hole on the SIM/microSD card tray to open it.2. Carefully slide out the tray.3. Insert the microSD card into the tray with the gold strips facing down (as shown).4. Insert the tray back into the slot and carefully push the tray in until it’s closed completely.NOTE: The microSD card is sold separately.Power/ Lock Button Using your phoneTurning your phone on/offTo turn your phone on, press and hold the Power/Lock button.Press and hold the Power/Lock button again to turn it off.Locking/unlocking the screenTo turn on your screen, press the Power/Lock button and then swipe up on the screen to unlock it.To turn off your screen and prevent accidental key presses, press the Power/Lock button.GH68-45545A_REV_1.1Printed in Korea .Para la versión en español, visite /supportMeet your phone.MicrophoneTop of phoneHome screen modeYou can select one of the two modes: Easy and Standard. Instructions in this guide are written using Standard mode.Standard mode is for users who are familiar with Android.Easy mode is a simplified experience for the first-time smartphone user.1.>>From the Home screen, tap Apps > Settings > Easymode .2. Choose the mode you want to use and tap Done .Additional i nformationYour wireless device and third-party servicesVerizon Wireless is the mobile carrier associated with this wireless device, but many services and features offered through this device are provided by or inconjunction with third parties. Verizon Wireless is not responsible for your use of this device or any non-Verizon Wireless applications, services and products, including any personal information you choose to use, submit or share with others. Specific third-party terms and conditions, terms of use and privacy policies apply. Please review carefully allapplicable terms, conditions and policies prior to using this wireless device and any associated application, product or service.Hearing aid compatibility informationThis phone has been tested and rated for use with hearing aids for some of the wireless technologies that it uses. However, there may be some newer technologies that have not been tested yet for use with hearing aids. It is important to try the different features of this phone thoroughly and in different locations, using your hearing aid or cochlear implant, to determine if you hear any interfering noise. Ask your service provider or the manufacturer of this phone for information on hearing aid compatibility. If you have questions about return or exchange policies, ask your service provider or phone retailer.© 2016 Verizon Wireless. All Rights Reserved.Managing your a ccountMy Verizon Mobile appManage your account, track your usage, edit account information, pay your bill and more.International travelFor features and rates when outside the US, visit/international .Customer service Call 1.800.922.0204 Twitter @VZWSupportThe Help app gives you tips,videos and other information on how to use your phone, including: Making calls Voice mail Sending texts Getting apps Taking photosAccessibilty settingsFrom your computer, visit/support .Download a User Guide from/support or call 1.888.987.HELP to order a copy.Learning moreAdvanced CallingYou can make High-Definition Voice and Video Calls and surf the web while you talk on the phone when you add Advanced Calling to your line. Visit /AdvancedCalling to learn how.Copying content from your old phone For help transferring contacts, photos and other content from your old phone wirelessly, visit /cloud .Or, to transfer content using the USB On the Go connector that came with your new phone, select Smart Switch during setup or open it later from the Home screen by tapping Apps > Settings > Backup and reset > Open Smart Switch .Visit /smartswitch for more information and a list of compatible phones.USB connector USB cableOld Device New Galaxy。