ACTPlus中文简易操作说明Ver1（3）

目录1. 快速应用指南 (8)2. 一般信息 (9)2.1. 应用围 (9)2.2. 适应征 (9)2.3. 禁忌症 (10)2.4. 警告 (10)2.5. 注意 (12)3. 介绍 (15)4. 间断的容积和热稀释测量 (19)4.1. 心输出量的测量原理 (19)4.2. 容积的测量原理 (19)4.3. 通过经肺热稀释法获得的参数 (22)4.3.1. 经肺心输出量（CO） (23)4.3.2. 胸腔血容积（ITBV） (23)全心舒末期容积（GEDV） (23)4.3.3. 血管外肺水（EVLW） (29)4.3.4. 肺血管通透性指数（PVPI） (33)4.3.6. 全心射血分数（GEF） (35)5. 脉搏轮廓分析 (36)5.1. 测量原理 (36)5.2. 脉搏轮廓分析的校正 (40)5.3. 通过脉搏轮廓分析获得的参数 (40)5.3.1. 脉搏轮廓心输出量（PCCO） (41)5.3.2. 动脉压（AP） (41)5.3.3. 每搏输出量变异（SVV） (42)5.3.4. 脉压变异（PPV） (42)5.3.5. 全身血管阻力（SVR） (43)5.3.6. 左心室收缩力指数（dP/dtmax） (44)6. 正常值围 (46)7. 文献 (48)8. 系统描述 (60)8.1. 一般信息 (64)8.1.1. 应用围 (64)8.1.2. 适应征 (64)8.1.4. 警告 (64)8.1.5. 注意 (67)8.2. 拆箱和检查 (70)8.2.1. 拆箱 (70)8.2.2. 检查 (70)8.3. 启动机器 (71)8.3.1. 要点 (71)8.3.2. 细节 (73)8.4. 菜单描述 (77)8.4.1. 输入菜单 (80)8.4.2. 压力调零菜单 (82)8.4.3. 设置菜单 (82)8.4.4. 主菜单 (84)8.4.5. 热稀释测量显示页 (86)8.4.6. 脉搏轮廓测量显示页 (92)8.4.7. 信息屏幕 (95)8.4.8. 热稀释信息屏幕 (97)8.5. 打印机 (98)8.6. 调整对比度 (99)8.7. 信号输入指示/警告指示 (100)8.8. 待机模式 (100)8.9. 电池功能 (101)8.10. 问题处理 (102)8.10.1. 出错信息 (102)8.10.2. 信号传输 (106)8.11. 设备的清洁和灭菌 (109)8.12. 维护/服务 (110)8.13. 将动脉压信号传输到床旁监护仪 (112)8.14. 使用RS232接口传输数据 (116)8.14.1. 一般情况 (116)8.14.2. 数据传输 (118)9. 消耗品 (119)9.1. PULSIOCATH PCCO导管套件 (119)9.2. PCCO压力测量套装 (121)9.3. 注射液温度探头固定仓 (121)9.4. PiCCO导管大包装 (121)9.5. 一次性使用的配件 (122)10. 配件 (123)11. 技术参数 (125)12. 附件 (127)A 计算公式 (127)B 国际符号 (134)C 服务保证 (135)D 名词解释 (137)E 认证证书 (142)图示图1：某种指示剂的稀释曲线图示及感兴趣的特定时间 (20)图2：指示剂在心肺系统的混合腔室图示 (21)图3：重症监护病人全心舒末期容积（GEDV）和胸腔血容积（ITBV）的回归分析 (24)图4：每搏输出量指数（SVI）和全心舒末期容积指数（GEDVI）的回归分析 (26)图5：猪的每搏输出量指数（SVI）和中心静脉压（CVP）回归分析 (27)图6：猪的每搏输出量指数（SVI）和肺毛细血管楔压（PCWP）回归分析 (28)图7：综合使用EVLW和ITBV治疗病人 (32)图8：全心舒末期容积指数（GEDVI）和心指数（CI）关系示意图 (35)图9：心脏周期的顺应性情况 (37)图10：个体主动脉顺应性的测量 (38)图11：脉搏轮廓心输出量（PCCO）的计算 (39)图12：PiCCO plus的前面板 (60)图13：PiCCO plus的后面板 (62)图14：PiCCO plus的连接 (71)图15：PiCCO plus软件操作流程图 (79)图16：打印机 (98)图17：压力信号传输到床旁监护仪时后面板的连接 (112)前言在使用PiCCO plus机器之前，请仔细阅读这本操作手册！警告为避免损伤病人和其他人员，操作者应了解本手册中的警告信息。

X9D PLUS 中文说明书1 遥控器菜单设置1.1 主画面1.1.1 主画面第一页开机后首先看到的就是主画面，主画面有四页，通过按遥控器MENU进行循环切换。

下面是首页的说明，说明顺序按照从遥控器屏幕的最上方到最下方。

7.6v遥控器电池电压，X9D使用6节镍氢电池小电池图标遥控器电池电量图标，显示电量剩余量。

->设置电量图标范围喇叭图标遥控器喇叭总音量。

->设置音量07:10当前时间。

->设置时间MODEL01模型名字 ->模型名字SA↑ SE ↑当前遥控器开关状态，例如SA↑表示SA开关拨到上方，SA-表示SA开关拨到中间等。

开关共有8个，SA-SH，其中SF为2档开关，SH为弹簧开关，其余均为三档开关。

开关的可以自定义，默认没有任何功能，开关可以用来直接控制舵面，如收放起落架，也可以定义为其他功能，比如改变飞行模式，调整大小舵，重设秒表，语音播报回传电压值，锁定油门…等等。

图片此处是您的模型的图片，可以在此处进行设置左右两侧较粗的竖条当前遥控器旋钮状态（左上：S1 右上：S2 左下：LS 右下：RS）。

旋钮的功能是自定义的，默认没有任何功能。

旋钮可以用来直接控制舵面，比如控制襟翼开启角度，也可以定义为其他功能，比如控制音量，控制方向舵-副翼混控比例，微调前起落架方向与方向舵混控的角度…等等左右和下方较细的竖条微调位置。

分别对应摇杆四个方向的微调。

[右方秒表]如果设置了秒表，在主画面右方会看见秒表，可以在此处进行设置1.1.2 主画面第二页在主画面第一页按PAGE进入主画面第二页，左右多出两个方框用来显示当前左右摇杆的位置，并且省略了秒表的显示。

其余与主画面第一页相同。

1.1.3 主画面第三页在主画面第二页按PAGE进入主画面第三页，右侧多出了一些下划线，用来显示LS1-LS32虚拟开关位置，当虚拟开关打开时，下划线会显示为竖条。

->虚拟开关。

并且省略了秒表的显示。

Commercial Unit (110 vac)B290400O P E R A T I N G M A N U A LACTISOL COMMERCIAL UNITOPERATING MANUALThank you and Congratulations on your choice of the Actisol®Commercial Unit, a revolutionary insecticide delivery system that uniquely combines the technology of foggers, misters, refillable sprayers and prepackaged aerosols.This refillable unit eliminates the need for costly prepackaged aerosols by mechanically generating the most optimum-sized, uniform insecticide particles. Its unique design allows you to treat more area per ounce than with pre-packaged aerosol products.It’s mobile, practical, and durable design make s it a valuable tool for all commercial accounts. In addition, it gives you the flexibility of using a variety of insecticides that are EPA approved for use in this type of equipment.Best of all, the Actisol® Commercial Unit provides deep harborage insect control, something you won’t get from pre-packaged aerosol products or conventional delivery systems. This system combines the right amount of insecticide with a high volume of moderately pressurized air to improve penetration through cracks and crevices to reach target insects deep within ceiling and wall voids. The Actisol® Commercial Unit eliminates insects in places other delivery systems can’t even reach.Manufactured in the USA By:Environmental Delivery Systems, Inc.314 Morningside DriveFriendswood, TX 77546OPERATING INSTRUCTIONSHandle with care.Do not place the unit where vibration and surface conditions would allow it to fall. Keep the unit on the ground when in use.Always wear personal protective equipment.When filling these units always wear protective eyewear and protective gloves. When operating these units, always wear protective clothing, eyewear, chemical resistant rubber gloves, and a respirator. Refer to the insecticide label for specific instructions and other precautions.1.Prepare area to be treated.Refer to insecticide label for directions on proper preparation for area to be treated before operating this equipment. General preparation includes:A.Remove all people and pets from the area to be treated.B.Remove all food, dishes, silverware, utensils or similar items that could come into contactwith the insecticide.C.Make sure all ventilation systems are turned off and windows are closed.D.Identify all areas where fire could result such as pilot lights or open flames.E.Make sure all aquarium filters and pumps are turned off and the tanks or ponds coveredto prevent contamination.2. Filter insecticide and fill tank.Turning counter clockwise remove fill cap (Item # 75) from tank. Filter insecticide by pouring slowly into fill neck and through the 50 mesh drop-in tank filter (Item # 74) to remove any debris that may clog or damage the Commercial Unit. DO NOT OVERFILL. If tank is too full it will overflow when the system is back flushed, as recommended. For best results fill tank about 80% full.3. Replace fill cap.Turning the cap clockwise, hand-tighten until firmly secured.4. Plug in / turn on power.A. Plug the Commercial Unit into a three-prong grounded, 110/115-volt electrical source. Use an additional three-prong grounded heavy-duty extension cord when operating this unit (Additional Cord Not Included).B. Remove red tip protector cap (Item # 34 - not shown in diagram) from the tip of the wand.C. Switch the unit to the ON position using the ON/OFF switch (Item # 79) located in the back of the unit on the right hand side.5. Adjust regulator.To adjust regulator (Item # 43) start by unlocking the safety lock located on the adjustment knob by pulling up on the knob. If a red ring is present, lift up on the red ring to unlock. Turn the knob slowly clockwise until the 0-30 psi back mount gauge (Item # 58) reads 17 - 20 psi.6. Purge air bubbles.Air pockets that develop may delay the shutoff of the aerosol after the trigger is released. To remove air pockets from the system turn the unit off, point the applicator tip into the original insecticide container, depress the trigger and wait until a pinstream flows from the tip. Hold for approximately 10 seconds to fully purge the system and allow for an uninterrupted pinstream.7. Turn the unit on to begin use.At this point the air flows freely through the twin tubing to the wand and excess air is vented to atmosphere at the tip. Next, the air flows into the regulator which controls the pressure exerted on the liquid inside the tank. The liquid product then travels through the second line of the twin tubing to the wand.8. Apply insecticide.A. Apply insecticide according to label instructions.B. Position the applicator tip on desired target.C. Depress the trigger to apply insecticide.Always apply insecticide according to the label instructions. Position the applicator tip on the desired target and depress the trigger to apply insecticide. Releasing the trigger allows the unit’s free airflow to push the already app lied insecticide deeper into harborage areas. The compressed air is environmentally safe and much more effective than chemical propellants. The free flowing air stream will also disturb target insects even without the use of liquid. The continuous free flowing air stream allows for deeper penetration of the target areas.The comfortable precision wand is balanced, easy to use, and easy to maintain. This unique wand is based on a common industry design making it simple to repair with easy access to replacement parts.Helpful Hints: Occasionally, when working overhead, the pressure exerted on the liquid tank by the regulator will not be sufficient to drive the liquid 8-10 feet above floor level.At this time, you need to increase the pressure on the liquid tank by adjusting the regulator clockwise to the point you receive the aerosol at the tip and at the height you desire to work.When operating the Actisol®System particle size may vary with pressure, but not as much as you think. What actually occurs is a higher rate of flow. In other words, you are using more liquid than needed to produce aerosol. The aerosols that you’ve probably used in the past were driven by propellant. Therefore, you saw larger particles and most of the material that was visible was that of the propellant. The Actisol® System utilizes no propellant. All you are seeing is the pesticide that has been sheared into micron sized particles. 98% are in the 2.4 to 15 micron size range. By increasing the pressure on the liquid tank you only increase the flow rate. The result being, using more pesticide than is required to do the job.9. Turn off unit / release pressure from tank.When necessary, switch the unit to the OFF position (Item # 79).To relieve pressure in the tank, press down on the pressure relief valve (Item # 69) located on the top of the fill cap (Item # 75).10. Back Flush System After Every Use to Remove Chemical From Wand and Hose.This procedure is highly recommended and is the mostimportant maintenance you can do for your system.A.Switch unit to the ON position (Item # 79).B.Turn regulator knob (Item # 43) counter clockwise until it stops.C.Relieve pressure in the tank by pressing down on the pressurerelief valve (Item # 69).D.Unscrew fill cap (Item # 75) by turning counter clockwise andremove.E.Holding the wand over the tank, place gloved finger over integrated stainless crack &crevice tip (Item # 2) exit orifice, stopping the flow of air, then squeeze the application trigger (Item # 23) until liquid is purged from the wand and hose. You will hear a gurgling sound coming from the tank when the process is complete. This process should take about 10 seconds.F.Remove gloved finger from tip and release trigger.G.Switch unit to OFF position (Item # 79).H.Replace fill cap (Item # 75) and tighten.I.Position red tip protector cap (Item # 34) over tip of wand for transportation of unit.Note: Back flush procedure should be performed after each use. This will help protect the polyurethane rubber hose in the wand (Item # 9) and the 50’ red twin tubing (Item # 61) and prevents unwanted spillage during transportation.11. Using the air chuck.The Commercial Unit is equipped with a 100 psi. capable airchuck (Item # 55) designed to pressurize a pneumatic duster, acompressed air sprayer fitted with an air valve (not included)and/or a tire of a service vehicle.To use the air chuck the compressor (Item # 31) must be running.Turn the handle of the ball valve (Item # 59), located on themanifold (Item # 78), in the cross line position. The adjustable 100 psi relief valve (Item #42) will relieve and produce a notable popping sound.Fit the air chuck on the pneumatic pressure duster, compressed air sprayer (fitted with an air valve) and pressu rize according to the equipment’s operating instructions.You can watch the pressure build on the 0-160 back mount gauge (Item # 56) and remove when desired pressure is reached.Note:The pressure relief valve is adjustable and should be preset to desired maximum pressure prior to use. Factory setting is 80 psi.12.Transporting the unit.Wrap the red twin hose (Item # 61) around the units storage cleats located on each side of the cart. To prevent bending or kinking the hose, avoid wrapping the hose too tight. Transport the Commercial Unit in an upright position. Take care not to damage the integrated crack & crevice tip (Item # 2) by positioning the red tip protector cap (Item # 34) over tip of wand after every use.Draining the Tank & Back Flushing1. Draining the tank.Drain the Commercial Unit’s tank when changing insecticides or storingfor an extended period of time.A.Switch unit to the ON position (Item # 79).B.Turn regulator knob (Item # 43) clockwise until 0-30 psi back mountgauge (Item # 58) reads 10-15 psi.C.Place drain tube (Item # 38) extending from the drain valve, intooriginal insecticide container.D.Turn handle on the tank drain valve assembly (Item # 64), it is locatedon the bottom right of the tank.E.Allow liquid to flow through tube into container until the tank isempty and air flows through the tube.F.Turn regulator knob (Item # 43) counter clockwise until it stops.2.Back flushing the system will remove chemical from wand and hose.This procedure should be performed after each use. This will helpprotect the polyurethane rubber hose in the wand (Item # 9) and the50’ red twin tubing (Item # 61) and prevents spillage duringtransportation.A. Place gloved finger over integrated crack & crevice tip (Item # 2) exitorifice, stopping the flow of air, then squeeze the application trigger(Item # 23) until liquid is purged from the wand and hose. You willhear a gurgling sound coming from the container and you will see nomore liquid traveling through the drain tube, only air will flow through drain tube when the process is complete. This process should take about 10 seconds.B. Remove gloved finger from tip and release trigger.C. Switch unit to OFF position (Item # 79).D. Replace fill cap (Item # 69) and tighten.E. Close the tank drain valve assembly (Item # 64).F. Position red tip protector cap (Item #34) over tip of wand for transportation of unit. Diagnosis and Field Service1.The unit is running and air is flowing from the tip, but no chemical aerosol is beingproduced.A.Make sure the tank contains insecticide.Remove tank cap (Item # 75), inspect tank for liquid. If there is no liquid in the tank, fill at least 25%.B.Check 50’ red twin tubing (Item # 61)) for kinks, crimps, twists, or other factors thatwould obstruct chemical flow to the wand.Unwrap the hose to free from kinking, crimping or blockage.C.Check the 0-30 pressure gauge (Item # 58).With the compressor running, it should read 17-20 psi.D.Be sure air pressure is reaching the wand tip.You should be able to hear and feel air flowing from the tip of the wand.E. Check for liquid flow with no air flow.Turn unit off, leave pressure in the tank, point the wand into the original insecticide container, and depress the trigger until a pinstream flows from the tip.If a pinstream flows from the tip with the compressor off and the tank under pressure:Remove integrated crack & crevice tip (Item # 2). Exit orifice should be maintained at .046”or use a drill bit #56. Drill exit orifice to resize.When used on abrasive surfaces the tip tends to close up reducing the amount of air that can escape resulting in excessive backpressure on the liquid.Also, be sure that all orifices in the fluid cap (Item # 5) are free of debris. Replace tip assembly and follow operating instructions to generate aerosol.F. If no liquid flow or pin stream, inspect fluid cap (Item # 5) by removing tip (Item # 2)and removing any debris from all orifices.2.The unit is running and the aerosol will not shut off at the tip when trigger is released.A.Unit may have air pockets created by surfaces forcing air back into the tip duringapplication.a.To release air pockets depress trigger and hold while aerosol is released. You will seeintermittent surges of aerosol, hold trigger until aerosol flows consistently withoutinterruption.b.Another method is to turn off the compressor and point tip into original insecticidecontainer and squeeze trigger to produce a pin stream. Allow to flow untiluninterrupted.B.Teflon seat (Item # 10) may be damaged or contain debris preventing positiveshutoff.First follow instructions for step number 10 of operating instructions to backflush liquid.Remove stainless airline (Item # 26) by removing compression nut at the elbow (Item # 32) to adapter body (Item # 8). Then remove adapter body (Item # 8) attached to valve body (Item # 12). Check exposed seat for debris, nicks, and scratches. Replace if necessary. Also inspect seat stem surface (Item # 24) for scratches or nicks. Replace if necessary.3.Airflow is low and aerosol is too heavy at normal 17 – 20 psi operating pressure.A.Fluid cap (Item # 5) may be damaged.Remove integrated crack & crevice tip (Item # 2). Inspect fluid cap (Item # 5) for cracks and debris around the air holes. The wheel should be stationary. It should not wiggle, spin or be crooked or smashed.B.Unit may be losing pressure due to a leak.With pressure in the tank, turn unit off and inspect for leaks at the pressure relief valve (Item # 69) and the tank cap o-ring (Item # 70). With the unit running inspect the 50’ red twin tubing (Item # 61) and entire wand in areas where air could escape, such as welds or fittings.Inspect for air leakage at the air chuck (Item # 55).4.While working with wand over-head air is flowing from the tip, but no chemical aerosolis being produced.A.A higher liquid pressure is necessary when wand is higher than 6’ from unit. Tocompensate simply adjust regulator (Item # 43) clockwise in one or two psi increments until desired flow is reached.Note: When returning to ground level operations reduce pressure by turning regulator (Item # 43) counter clockwise and releasing pressure from the tank by pushing the button on the pressure relief valve (Item # 69) until reaching 17 - 20 psi on gauge.If none of these solutions corrects your problem, there may be something more serious wrong with the unit. For additional technical assistance please contact Environmental Delivery Systems, Inc. Technical Services Department.Insecticides1. Observe label directions.Do not operate the Actisol®Commercial Unit with insecticides notlabeled for aerosol, fog or mist applications. Read the insecticide labelto determine if the insecticide is EPA- approved for use in this type ofequipment. Contact your chosen distributor for Information oninsecticides currently labeled for use in equipment such as ActisolDelivery Systems.PartsParts for the Actisol® Commercial Unit can be ordered through your chosen distributor. When ordering spare or replacement parts refer to the exploded diagram and the product codes on the parts list in this manual.ServiceIf the Actisol® Commercial Unit requires factory service be sure to drain the tank, back flush the wand and hose, and pack the unit in its original carton and packing material for shipping. If the original carton is not available, pack the unit a durable box and protect the unit as best you can. If using foam packing materials be sure to place the unit in a plastic bag before adding materials to carton.Ship the unit with a description of the problem, a contact name and phone number, and a return shipping address to:Environmental Delivery Systems, Inc.314 Morningside DriveFriendswood, TX 77546281-993-0019 – PhoneNote: Post warranty service will be billed for parts, labor, packaging (if needed), and freight.2342835NOTE:Item #2 Exit Orifice inside diameter must be maintained at or about 0.046 or use a # 56 drill bit.2 3428 35 NOTE: Item #2 Exit Orifice inside diameter must be maintained at or about 0.046 or use a # 56 drill bit. ACTISOL ® WAND —18”ACTISOL® WAND –18”74767950494549ACTISOL® COMMERCIAL UNIT EXPOLDEDPRODUCT LIMTED WARRANTYEnvironmental Delivery Systems, Inc. and it’s products are warranted to be defect free in materials and workmanship under normal use, for a period of (1) year from the date of manufacture or (1) year of use, with proof of purchase. This limited warranty will not exceed (2) years, in any event.Environmental Delivery Systems, Inc. shall not be liable for freight damage incurred during shipping. Package returns carefully. If the original carton is not available, pack the unit in a durable box and protect the unit as best you can. If using foam packing materials, be sure to place the unit in a plastic bag before adding materials to carton.Environmental Delivery Systems, Inc.’s obligation under this warranty policy is limited to the repair or replacement of the unit. All returns will be tested per Environmental Delivery Systems, Inc. factory criteria. Units found not defective, under the terms of this limited warranty, are subject to the charges paid by the returnee.Warranty replacement will be shipped on a freight allowed basis. Environmental Delivery Systems, Inc. reserves the right to choose the method of transportation.This limited warranty is in lieu of all other warranties, expressed or implied, and no other person is authorized to give any other warranty or assume obligation or liability on Environmental Delivery Systems, Inc.’s behalf. Environmental Delivery Systems, Inc. shall not be li able for any labor, damage or other expense, nor shall Environmental Delivery Systems, Inc. be liable for any indirect, incidental or consequential damages of any kind incurred by the reason of the use or sale of any defective product or part.Return PolicyAll units must be flushed of any chemicals before shipping. Carriers, including U.S.P.S., airlines, UPS, ground freight, etc. require specific identification of any hazardous materials to be shipped. Failure to do so may result in a substantial fine and/or prison term. Check with your shipping company for specific instructions.All Units must be flushed of any chemical (ref. OSHA Section 1910.1200 (d)(e)(f)(g)(h)) and NO hazardous chemicals will be accepted for service or warranty consideration. Environmental Delivery Systems, Inc. reserves the right to request a Material Safety Data Sheet from the returnee for any product it deems necessary. Environmental Delivery Systems, Inc. reserves the right to “disposition as scrap” any products returned wh ich contain unknown fluids. Environmental Delivery Systems, Inc. reserves the right to charge the returnee for all costs incurred for chemical testing and proper disposal of components containing unknown fluids. Environmental Delivery Systems, Inc. requests this in order to protect the environment and personnel from the hazards of handling unknown fluids.。

CT-1PLUS全自动滴定仪软件用户使用手册一、概述1.1仪器简介滴定分析是将已知浓度的标准滴定溶液滴加到所需测试的物质的溶液中，滴定液和需要检测的物质按一定的化学计量关系完全反应，根据所消耗的已知浓度的标准滴定溶液的体积，来计算出被测物质的含量。

这种测试方法时根据准确测量滴定溶液的体积为基础的，故也可称为容量分析。

手动滴定时，需要根据指示剂的颜色变化来判定测量的终点，CT-1PLUS多功能滴定仪可以根据滴定过程中电极电位的变化来自动确定终点，对于电位变化不明显的反应，也可自动根据摄像头采集的颜色变化来自动判断滴定终点，大大简化和降低的认为的操作和判断误差，提高的测试的准确性。

CT-1PLUS多功能滴定仪是上海七阳信息科技有限公司设计开发的具有自主知识产权的智能滴定仪。

采用7英寸中文人机对话全彩触摸屏，免维护高精度滴定管、电磁切换阀、高分辨率的颜色采集模块和多样的检测模块，将简单易懂的操作、高准确性的终点判断、高精度的滴定控制完美地结合在一起。

通过测量电极的电位变化和颜色变化的自动判断，来指示滴定的终点，根据样品性质，仪器选用不同电极和检测器进行自动颜色滴定、pH滴定、氧化还原滴定、络合滴定、非水滴定和沉淀滴定等多种滴定，适用于化工、食品、制药、冶金、生物、环保、科研及高等院校等领域。

1.2仪器特点*彩色触摸屏设计，中文操作界面，简洁易懂。

*用户可以根据不同测试选择不同终点判断方法，可以固定终点值判断终点、设置终点判断区间和微分结合判断终点或者自动判断终点。

*具有手动滴定和自动滴定功能。

*两种滴定台选择：磁力搅拌或杆式螺旋搅拌，均采用PWM调制技术，滴定台支架升降系统更能方便用户加样以及清洗操作。

*多项专利技术使仪器运行平稳无噪音，坚实耐用，维护更方便。

*多种数据接口可实现测试数据和图谱的打印，数据备份，满足GLP规范。

*用户管理功能，可根据不同的操作人员设置不同的操作权限，确保数据的保密性。

*仪器选用不同电极可进行：颜色滴定、酸碱滴定、氧化还原滴定、络合滴定、非水滴定和pH测量、电导滴定等多种滴定，具备温度探头实现pH 滴定温度补偿。

BioPhotometer plus 操作指南新型面板介绍：检测前准备：1， 打开仪器和打印机（如果需要的话）开关2， 准备好比色皿，空白溶液，标准溶液和样品。

标准品和样品的溶液若低于吸光度0.02-0.03A（相当于dsDNA 1.0-1.5 μg/ml的浓度）不可再使用3， 打开样品滑盖常规检测步骤：1， 在面板检测方法中选择需要的方法，使用前先检查所选方法的参数设置是否正确按下enter键，显示屏如下1， 依次放入空白（按blank键）、标准品（按standard键）和样品（按sample 键），再按enter键分别进行检测2， 完成检测后合上滑盖，关闭电源。

检测方法：BioPhotmeter plus 在出厂前已预存以下检测方法，可以直接调用。

检测方法组检测方法 解释 波长双链DNA 单链DNADNA 低聚糖DNA根据不同的参数值来计算DNA 浓度。

预设的参数值不同，检测方法也不同。

检测波长：260 nm检测纯度的次波长：230，280，340 nm RNA RNA 低聚糖RNA同DNA 检测组类似 同DNA 检测组类似BCA 微量BCA550 nmBRADFORD微量BRADFORD595 nm LOWRY 微量LOWRY加好试剂后计算蛋白的浓度。

检测方法通过校准曲线的评估程序来预先编程。

标准品的代号和目标浓度的可以修改 595 nm蛋白 蛋白280 nm 根据参数值来计算蛋白浓度 检测波长：280 nm检测纯度的次波长：260， 340 nmOD 600 OD 600 浊度检测可以测量细菌密度 595 nmDYE 550 – 双链DNA DYE 550 – 单链DNA DYE 550 – RNA DYE 550 – 寡核苷酸dye 550 DYE 550 – 蛋白检测染料标记的生物分子：计算分子（核酸或蛋白）的浓度以及单一测量步骤中的染料。

同时还能检测生物分子的染料标记率。

DNA/RNA/寡核苷酸：参考DNA 和RNA 的检测组 蛋白：参考蛋白检测组中的蛋白 280 nm 染料的检测波长：550 nm DYE 650 – 双链DNA DYE 650 – 单链DNADYE 650 – RNADYE 650 – 寡核苷酸dye 650 DYE 650 – 蛋白同“dye 550”检测方法 DNA/RNA/寡核苷酸：参考DNA 和RNA 的检测组 蛋白：参考蛋白检测组中的蛋白 280 nm 染料的检测波长：650 nm 340 检测 ASSAY 340/1 ASSAY 340/2ASSAY 340/3在340nm 处检测来计算浓度。

ACT Plus操作规程以下内容仅供参考。

使用ACT Plus仪器前，请务必仔细阅读使用说明书！一、预热1．开ACT Plus电源，让机器预热10分钟。

2．将药筒放入试剂槽中(此时切勿将试剂槽推入机器中)，预热3－5分钟。

3．必要时请输入患者ID，用户ID和药筒批号。

4．选择适当的药筒类型（Cartridge Type），一般为HR-ACT。

二、测试1．用注射器抽取约1ml血样2．将药筒自试剂槽中取出，轻弹药筒底部，使高岭土试剂混匀。

3．将注射器的针头插入药筒至底部，缓缓注入血样，注意避免气泡在试管中产生。

4．当血样液平面到达两刻度线之间时，停止注入，取出针头，取出针头时需注意不要将针头血滴粘附在试管内壁和黑色旗标杆上。

5．将药筒放入试剂槽，轻轻推入机器，开始测试。

6．测试结束时液晶屏上会显示两个通道的平均值（Average）和差异值（Difference），若Difference/Average * 100% <12%，则测试成功，接受该平均值，同时记录下差异值备查。

三、测试中可能出现的问题1．测试进行至25秒左右，试剂槽弹出，屏幕上两个通道都显示“- - -”；或伴随“嘀”声，屏幕上一个通道显示“- - -”，另一个通道继续测试。

可能原因：注血方式错误。

注血时，注血速度一定要慢，否则会在血样中产生气泡，在测试开始的前20秒，气泡的表面张力将会阻止黑色旗标杆下落，造成测试参考时间无法建立，20秒后将会显示“- - -”，测试无法正常进行。

2．两通道测试时间相差过大。

（系指Difference/Average * 100%>12%）可能原因：A. 注血时，有血样沾附在其中一试管刻度线以上的内壁或黑色旗标杆上，造成测试过程中，黑色旗标杆粘附在试管内壁，无法下落，提前结束测试。

B. 试管两通道中血样注射量差异过大。

3．将试剂槽推入测试位置后，试剂槽立刻弹出，屏幕显示“4”。

可能原因：光路故障，您可以使用随机提供的棉签，沾清水擦拭光路。