当前位置：文档之家 › MAX4174AOEUK+中文资料

MAX4174AOEUK+中文资料

  • 格式：pdf
  • 大小：304.41 KB
  • 文档页数：20

For free samples & the latest literature: , or phone 1-800-998-8800.For small orders, phone 1-800-835-8769.General DescriptionThe MAX4174/MAX4175/MAX4274/MAX4275 Gain-Amp™ family combines a low-cost Rail-to-Rail ®op amp with precision internal gain-setting resistors and V CC / 2biasing. Factory-trimmed on-chip resistors decrease design size, cost, and layout, and provide 0.1% gain accuracy. Fixed inverting gains from -0.25V/V to -100V/V or noninverting gains from +1.25V/V to +101V/V are available. These devices operate from a single +2.5V to +5.5V supply and consume only 300µA.GainAmp amplifiers are optimally compensated for each gain version, achieving exceptional GBW prod-ucts up to 23MHz (A V = +25V/V to +101V/V). High-volt-age fault protection withstands ±17V at either input without excessive current draw.Three versions are available in this amplifier family: single/dual/quad open-loop, unity-gain stable (MAX4281/MAX4282/MAX4284); single/dual fixed gain (MAX4174/MAX4274); and single/dual fixed gain plus internal V CC / 2bias at the noninverting input (MAX4175/MAX4275), which simplifies input biasing in single-supply designs. The input common-mode voltage range of the open-loop amplifiers extends from 150mV below the negative supply to within 1.2V of the positive supply.The outputs can swing rail-to-rail and drive a 1k Ωload while maintaining excellent DC accuracy. The amplifier is stable for capacitive loads up to 470pF.ApplicationsPortable Instruments Smart-Card ReadersInstruments, Terminals, Infrared Receivers for and Bar-Code Readers Remote ControlsKeyless EntryLow-Side Current-Sense Photodiode PreampsAmplifiersFeatureso GainAmp Family Provides Internal Precision Gain-Setting Resistors in SOT23 (MAX4174/5)o 0.1% Gain Accuracy (R F /R G ) (MAX4174/5,MAX4274/5)o 54 Standard Gains Available (MAX4174/5,MAX4274/5)o Open-Loop Unity-Gain-Stable Op Amps (MAX4281/2/4)o Rail-to-Rail Outputs Drive 1k ΩLoado Internal V CC / 2 Biasing (MAX4175/MAX4275)o +2.5V to +5.5V Single Supply o 300µA Supply Current o Up to 23MHz GBW Producto Fault-Protected Inputs Withstand ±17V o Stable with Capacitive Loads Up to 470pF with No Isolation ResistorMAX4174/5, MAX4274/5, MAX4281/2/4†SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps________________________________________________________________Maxim Integrated Products119-1407; Rev 3; 8/99Ordering Information continued at end of data sheet.*Insert the desired gain code (from the Gain Selection Guide)in the blank to complete the part number.††Refer to the Gain Selection Guide for a list of preferred gains and SOT Top Marks.Ordering InformationGainAmp is a trademark of Maxim Integrated Products. Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.†Patent pendingPin ConfigurationsTypical Operating CircuitSelector Guide appears at end of data sheet.M A X 4174/5, M A X 4274/5, M A X 4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps 2_______________________________________________________________________________________ABSOLUTE MAXIMUM RATINGSELECTRICAL CHARACTERISTICS—MAX4174/MAX4175/MAX4274/MAX4275 Fixed-Gain Amplifiers(V CC = +2.5V to +5.5V, V EE = 0, V IN+= V IN-= V CC / 2, R L to V CC / 2, R L = open, T A = T MIN to T MAX , unless otherwise noted. Typical values are at V CC = +5V and T A = +25°C.) (Note 1)Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.Supply Voltage (V CC to V EE )....................................-0.3V to +6V Voltage Inputs (IN_)MAX4281/4282/4284.....................(V EE - 0.3V) to (V CC + 0.3V)MAX4174/4175/4274/4275 (with respect to GND)...........±17V Output Short-Circuit Duration(OUT_).....................................Continuous to Either V EE or V CC Continuous Power Dissipation (T A = +70°C)5-Pin SOT23 (derate 7.1mW/°C above +70°C).............571mW 8-Pin SO (derate 5.88mW/°C above +70°C).................471mW8-Pin µMAX (derate 4.1mW/°C above +70°C)............330mW 14-Pin SO (derate 8.3mW/°C above +70°C)...............667mW 16-Pin QSOP (derate 8.3mW/°C above +70°C)..........667mW Operating Temperature Range ...........................-40°C to +85°C Maximum Junction Temperature.....................................+150°C Storage Temperature Range.............................-65°C to +150°C Lead Temperature (soldering, 10sec).............................+300°CELECTRICAL CHARACTERISTICS—MAX4174/MAX4175/MAX4274/MAX4275 Fixed-GainMAX4174/5, MAX4274/5, MAX4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps Amplifiers (continued)= +2.5V to +5.5V, V= 0, V= V= V/ 2, R to V/ 2, R= open, T= T to T, unless otherwise noted. Typical(VELECTRICAL CHARACTERISTICS—MAX4281/MAX4282/MAX4284 Open-Loop Op Amps (V CC= +2.5V to +5.5V, V EE= 0, V IN+= V IN-= V CC/ 2, R L to V CC/ 2, R L= open, T A= T MIN to T MAX, unless otherwise noted. Typicalvalues are at V CC= +5V and T A= +25°C.) (Note 1)Typical Operating Characteristics(V CC = +5V, R L = 100k Ωto V CC / 2, small-signal V OUT = 100mVp-p, large-signal V OUT = 1Vp-p, T A = +25°C, unless otherwise noted.)M A X 4174/5, M A X 4274/5, M A X 4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps 4_______________________________________________________________________________________Note 1:MAX4174/MAX4175/MAX4281 and MAX4274/MAX4275/MAX4282 and MAX4284 are 100% production tested atT A = +25°C. All temperature limits are guaranteed by design.Note 2:Guaranteed by design.Note 3:The input common-mode range for IN_+ is guaranteed by a functional test. A similar test is done on the IN_- input. See theApplications Information section for more information on the input voltage range of the GainAmp.Note 4:For A V = -0.5V/V and A V = -0.25V/V, the output voltage swing is limited by the input voltage range.Note 5:Includes noise from on-chip resistors.Note 6:The gain accuracy test is performed with the GainAmp in noninverting configuration. The output voltage swing is limited bythe input voltage range for certain gains and supply voltage conditions. For situations where the output voltage swing is lim-ited by the valid input range, the output limits are adjusted accordingly.4-61k100k 1M10k10MLARGE-SIGNAL GAIN vs. FREQUENCYFREQUENCY (Hz)N O R M A L I Z E D G A I N (d B )-5-4-3-2-101234-61k100k 1M10k10MLARGE-SIGNAL GAIN vs. FREQUENCYFREQUENCY (Hz)N O R M A L I Z E D G A I N (d B )-5-4-3-2-101234-61k 100k 1M 10k 10MLARGE-SIGNAL GAINvs. FREQUENCYFREQUENCY (Hz)N O R M A L I Z E D G A I N (d B )-5-4-3-2-10123ELECTRICAL CHARACTERISTICS—MAX4281/MAX4282/MAX4284 Open-Loop Op Amps (continued)(V CC = +2.5V to +5.5V, V EE = 0, V IN+= V IN-= V CC / 2, R L to V CC / 2, R L = open, T A = T MIN to T MAX , unless otherwise noted. Typical values are at V = +5V and T = +25°C.) (Note 1)MAX4174/5, MAX4274/5, MAX4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps_______________________________________________________________________________________5Typical Operating Characteristics (continued)(V CC = +5V, R L = 100k Ωto V CC / 2, small-signal V OUT = 100mVp-p, large-signal V OUT = 1Vp-p, T A = +25°C, unless otherwise noted.)4-61k100k 1M10k10MLARGE-SIGNAL GAIN vs. FREQUENCYFREQUENCY (Hz)N O R M A L I Z E D G A I N (d B )-5-4-3-2-101234-61k100k 1M10k10MLARGE-SIGNAL GAIN vs. FREQUENCYFREQUENCY (Hz)N O R M A L I Z E D G A I N (d B )-5-4-3-2-101234-61k 100k 1M 10k 10MLARGE-SIGNAL GAIN vs. FREQUENCYFREQUENCY (Hz)N O R M A L I Z E D G A I N (d B )-5-4-3-2-101234-61k100k 1M10k10MSMALL-SIGNAL GAIN vs. FREQUENCYFREQUENCY (Hz)N O R M A L I Z E D G A I N (d B )-5-4-3-2-101234-61k100k 1M10k10MSMALL-SIGNAL GAINvs. FREQUENCYFREQUENCY (Hz)N O R M A L I Z E D G A I N (d B )-5-4-3-2-101234-61k 100k 1M 10k 10MSMALL-SIGNAL GAINvs. FREQUENCYFREQUENCY (Hz)N O R M A L I Z E D G A I N (d B )-5-4-3-2-10123MAX4174/MAX41754-61k100k 1M10k10M SMALL-SIGNAL GAIN vs. FREQUENCYFREQUENCY (Hz)N O R M A L I Z E D G A I N (d B )-5-4-3-2-101234-61k 100k 1M 10k 10M SMALL-SIGNAL GAIN vs. FREQUENCYFREQUENCY (Hz)N O R M A L I Z E D G A I N (d B )-5-4-3-2-101234-61k 100k 1M 10k 10MSMALL-SIGNAL GAIN vs. FREQUENCYFREQUENCY (Hz)N O R M A L I Z E D G A I N (d B )-5-4-3-2-10123M A X 4174/5, M A X 4274/5, M A X 4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps 6_______________________________________________________________________________________1k10k100k1MTOTAL HARMONIC DISTORTIONvs. FREQUENCYFREQUENCY (Hz)T H D (d B )0-120-100-80-60-40-201k10k100k1MTOTAL HARMONIC DISTORTIONvs. FREQUENCYFREQUENCY (Hz)T H D (d B )0-120-100-80-60-40-20-120-90-100-110-80-70-6002.01.50.5 1.0 2.53.0 3.54.0 4.55.0TOTAL HARMONIC DISTORTION vs. OUTPUT VOLTAGE SWINGVOLTAGE SWING (Vp-p)T H D (d B )Typical Operating Characteristics (continued)(V CC = +5V, R L = 100k Ωto V CC / 2, small-signal V OUT = 100mVp-p, large-signal V OUT = 1Vp-p, T A = +25°C, unless otherwise noted.)MAX4174/MAX4175-120-90-100-110-80-70-6002.01.50.5 1.0 2.53.0 3.54.0 4.55.0TOTAL HARMONIC DISTORTION vs. OUTPUT VOLTAGE SWINGVOLTAGE SWING (Vp-p)T H D (d B )1101001k10k100kVOLTAGE NOISE DENSITY vs. FREQUENCY(A V = +1.25, +3, +10)FREQUENCY (Hz)100010100V O L T A G E N O I S E D E N S I T Y (n V /H z )1101001k10k100kVOLTAGE NOISE DENSITY vs. FREQUENCY(A V = +25, +51)FREQUENCY (Hz)100010100V O L T A G E N O I S E D E N S I T Y (n V /√H z )1101001k10k100kCURRENT NOISE DENSITY vs.FREQUENCYM A X 4174/5 t o c 19FREQUENCY (Hz)101C U R R E N T N O I S EDE N S I T Y (f A /√H z )MAX4174/5, MAX4274/5, MAX4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps_______________________________________________________________________________________7Typical Operating Characteristics (continued)(V CC = +5V, R L = 100k Ωto V CC / 2, small-signal V OUT = 100mVp-p, large-signal V OUT = 1Vp-p, T A = +25°C, unless otherwise noted.)2µs/divC L = 0INPUT VOLTAGEA V = +1.25V/VOUTPUT 500mV/divA V = +3V/V OUTPUT 50mV/divA V = +5V/V OUTPUT 500mV/divA V = +10V/V OUTPUT 500mV/divA V = +25V/V OUTPUT 500mV/divA V = +51V/V OUTPUT 500mV/divM A X 4174/5 t o c 20LARGE-SIGNAL PULSE RESPONSE2µs/divC L = 0INPUT VOLTAGEA V = +1.25V/VOUTPUT 50mV/divA V = +3V/V OUTPUT 50mV/divA V = +5V/V OUTPUT 50mV/divA V = +10V/V OUTPUT 50mV/divA V = +25V/V OUTPUT 50mV/divA V = +51V/V OUTPUT 50mV/divM A X 4174/5 t o c 21SMALL-SIGNAL PULSE RESPONSEMAX4174/MAX4175M A X 4174/5, M A X 4274/5, M A X 4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps 8_______________________________________________________________________________________Typical Operating Characteristics (continued)(V CC = +5V, R L = 100k Ωto V CC / 2, small-signal V OUT = 100mVp-p, large-signal V OUT = 1Vp-p, T A = +25°C, unless otherwise noted.)-200-100-150500-50150100200-50-510-35-202540557085INPUT OFFSET VOLTAGE vs.TEMPERATURETEMPERATURE (°C)I N P U T O F F S E T V O L T A G E (µV )-20002004006008001000-45-15-300153045607590INPUT BIAS CURRENT vs. TEMPERATURETEMPERATURE (°C)I N P U T B I A S C U R R E N T (p A )240280260320300360340380-50-20-5-35102540557085SUPPLY CURRENT vs. TEMPERATURETEMPERATURE (°C)S U P P L Y C U R R E N T (µA )-100-60-80-20-40200408060100-50-20-510-352540557085V OH AND V OL vs. TEMPERATURE(V CC = 2.5V)TEMPERATURE (°C)V O L T A G E (m V )-100-60-40-20-80406002080100160180120140200-50-20-510-352540557085V OH AND V OL vs. TEMPERATURE(V CC = 5.5V)TEMPERATURE (°C)V O L T A G E (m V )MAX4174/MAX4175/MAX4281/MAX4282/MAX4284-7010010k 100k1k1MPOWER-SUPPLY REJECTIONvs. FREQUENCYM A X 4174 T O C 22FREQUENCY (Hz)P S R (d B )-95-90-85-80-7510010k 100k1k1MOUTPUT IMPEDANCE vs. FREQUENCYM A X 4174 T O C 23FREQUENCY (Hz)O U T P U T I M P E D A N C E (Ω)1000.010.11105.04.0110100OUTPUT VOLTAGE SWINGvs. R LOADM A X 4174 T O C 24R LOAD (k Ω)V S W I N G (V p -p )4.94.84.74.64.54.44.34.24.1MAX4174/5, MAX4274/5, MAX4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps_______________________________________________________________________________________9110k 1M100101k 100k 10MOPEN-LOOP GAIN AND PHASEvs. FREQUENCYM A X 4174/5 t o c 30FREQUENCY (Hz)O P E N -L O O P G A I N (d B )P H A S E (d e g r e e s )1401201008060400-20-4020160-45-90-135-180-225-270-31504-6-51k10k100k 1M10M SMALL-SIGNAL GAIN vs. FREQUENCY-4-3M A X 4174/5 t o c 31FREQUENCY (Hz)G A I N (d B )-2-101234-1-2-3-4-5-61k 10k 100k 1M 10MLARGE-SIGNAL GAIN vs. FREQUENCY0M A X 4174/5 t o c 32FREQUENCY (Hz)G A I N (d B )1230-50-60-70-80-90-1001k10k100k1001M10MCOMMON-MODE REJECTIONvs. FREQUENCY-40M A X 4174/5 t o c 33FREQUENCY (Hz)C M R (d B)-30-20-100-60-80-70-90-100-110-10-20-30-40-50-1201M1k10k100kTOTAL HARMONIC DISTORTIONvs. FREQUENCYFREQUENCY (Hz)T H D (d B )100010010101001k110k100kVOLTAGE NOISE DENSITYvs. FREQUENCYM A X 4174/5 t o c 34FREQUENCY (Hz)V O L T A G E N O I S E D E N S I T Y (n V /√H z )101101001k 110k 100kCURRENT NOISE DENSITYvs. FREQUENCYM A X 4174/5 t o c 35FREQUENCY (Hz)C U R R E N T N O I S EDE N S I T Y (f A /√H z )-50-80-90-85-95-55-60-65-70-751M10M1k10k100k MAX4282CROSSTALK vs. FREQUENCYM A X 4174/5 t o c 37FREQUENCY (Hz)C R OS S T A L K (d B )-50-55-60-65-70-751M10M1k10k100k MAX4284CROSSTALK vs. FREQUENCYFREQUENCY (Hz)C R O S S T A L K (d B )Typical Operating Characteristics(V CC = +5V, R L = 100k Ωto V CC / 2, small-signal V OUT = 100mVp-p, large-signal V OUT = 1Vp-p, T A = +25°C, unless otherwise noted.)MAX4281/MAX4282/MAX4284M A X 4174/5, M A X 4274/5, M A X 4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps 10______________________________________________________________________________________Functional DiagramsPin DescriptionDetailed Description Maxim’s GainAmp fixed-gain amplifiers combine a low-cost rail-to-rail op amp with internal gain-setting resis-tors. Factory-trimmed on-chip resistors provide 0.1% gain accuracy while decreasing design size, cost, and layout. Three versions are available in this amplifier family: single/dual/quad open-loop, unity-gain-stable devices (MAX4281/MAX4282/MAX4284); single/dual fixed-gain devices (MAX4174/MAX4274); and single/ dual devices with fixed gain plus internal V CC / 2 bias at the noninverting input (MAX4175/MAX4275). All amplifiers feature rail-to-rail outputs and drive a 1kΩload while maintaining excellent DC accuracy.Open-Loop Op Amps The single/dual/quad MAX4281/MAX4282/MAX4284 are high-performance, open-loop op amps with rail-to-rail outputs. These devices are compensated for unity-gain stability, and feature a gain bandwidth (GBW) of 2MHz. The op amps in these ICs feature an input com-mon-mode range that extends from 150mV below the negative rail to within 1.2V of the positive rail. These high performance op amps serve as the core for this family of GainAmp fixed-gain amplifiers. Although the -3dB bandwidth will not correspond to that of a fixed-gain amplifier in higher gain configurations, these open-loop op-amps can be used to prototype designs.Internal Gain-Setting Resistors Maxim’s proprietary laser trimming techniques produce the necessary R F/R G values (Figure 1), so many gain offerings are easily available. These GainAmp fixed-gain amplifiers feature a negative-feedback resistor network that is laser trimmed to provide a gain-setting feedback ratio (R F/R G) with 0.1% typical accuracy. The standard op amp pinouts allow the GainAmp fixed-gain amplifiers to drop in directly to existing board designs, easily replacing op-amp-plus-resistor gain blocks.GainAmp Bandwidth GainAmp fixed-gain amplifiers feature factory-trimmed precision resistors to provide fixed inverting gains from -0.25V/V to -100V/V or noninverting gains from +1.25V/V to +101V/V. The op-amp core is decompen-sated strategically over the gain-set options to maxi-mize bandwidth. Open-loop decompensation increases GBW product, ensuring that usable bandwidth is main-tained with increasing closed-loop gains. A GainAmp with a fixed gain of A V= 100V/V has a -3dB bandwidth of 230kHz. By comparison, a unity-gain-stable op amp configured for A V= 100V/V would yield a -3dB band-width of only 20kHz (Figure 2). Decompensation is per-formed at five intermediate gain sets, as shown in the Gain Selection Guide. Low gain decompensation great-ly increases usable bandwidth, while decompensation above gains of +25V/V offers diminished returns.V CC / 2 Internal Bias The MAX4175/MAX4275 GainAmp fixed-gain amplifiers with the V CC / 2 bias option are identical to standard GainAmp fixed-gain amplifiers, with the added feature of V CC / 2 internal bias at the noninverting inputs. Two 150kΩresistors form a voltage-divider for self-biasing the noninverting input, eliminating external bias resis-tors for AC-coupled applications, and allowing maxi-mum signal swing at the op amp’s rail-to-rail output for single-supply systems (see Typical Operating Circuit). For DC-coupled applications, use the MAX4174/ MAX4274.High-Voltage (±17V) Input Fault Protection The MAX4174/MAX4175/MAX4274/MAX4275 include ±17V input fault protection. For normal operation, see the input voltage range specification in the Electrical Characteristics. Overdriven inputs up to ±17V will notFigure 1. Internal Gain-Setting ResistorsFigure 2. Gain-Bandwidth ComparisonMAX4174/5, MAX4274/5, MAX4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps______________________________________________________________________________________11M A X 4174/5, M A X 4274/5, M A X 4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps 12______________________________________________________________________________________cause output phase reversal. A back-to-back SCR structure at the input pins allows either input to safely swing ±17V relative to V EE (Figure 3). Additionally, the internal op-amp inputs are diode clamped to either supply rail for the protection of sensitive input stage cir-cuitry. Current through the clamp diodes is limited by a 5k Ωresistor at the noninverting input, and by R G at the inverting input. An IN+ or IN- fault voltage as high as ±17V will cause less than 3.5mA of current to flow through the input pin, protecting both the GainAmp and the signal source from damage.Applications InformationGainAmp fixed-gain amplifiers offer a precision, fixed gain amplifier in a small package that can be used in a variety of circuit board designs. GainAmp fixed-gain amplifiers can be used in many op amp circuits that use resistive negative feedback to set gain, and that do not require other connections to the op-amp inverting input.Both inverting and noninverting op-amp configurations can be implemented easily using a GainAmp.GainAmp Input Voltage RangeThe MAX4174/MAX4175/MAX4274/MAX4275 combine both an op amp and gain-setting feedback resistors on the same chip. Because the inverting input pin is actu-ally tied to the R G input series resistor, the inverting input voltage range is different from the noninverting input voltage range. Just as with a discrete design,care must be taken not to saturate the inputs/output of the core op amp, to avoid signal distortions or clipping.The inverting inputs (IN_-) of the MAX4174/MAX4175/MAX4274/MAX4275 must be within the supply rails or signal distortion may result. The GainAmp’s inverting input structure includes diodes to both supplies, such that driving the inverting input beyond the rails may cause signal distortions (Figure 1). For applications that require sensing voltages beyond the rails, use the MAX4281/MAX4282/MAX4284 open-loop op amps (Figure 4).Figure 3. Input ProtectionMAX4174/5, MAX4274/5, MAX4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps______________________________________________________________________________________13GainAmp Signal Couplingand ConfigurationsCommon op-amp configurations include both nonin-verting and inverting amplifiers. Figures 5–8 show vari-ous single and dual-supply circuit configurations.Single-supply systems benefit from a midsupply bias on the noninverting input (provided internally on MAX4175/MAX4275), as this produces a quiescent DC level at the center of the rail-to-rail output stage signal swing. For dual-supply systems, ground-referenced signals may be DC-coupled into the inverting or non-inverting inputs.IN_+ Filter on MAX4175/MAX4275Internal resistor biasing of the V CC / 2 bias options cou-ples power-supply noise directly to the op amp’s nonin-verting input. To minimize high-frequency power-supply noise coupling, add a 1µF to 0.1µF capacitor from IN+to ground to create a lowpass filter (Figure 6). The low-pass filter resulting from the internal bias resistors and added capacitor can help eliminate higher frequency power-supply noise coupling through the noninverting input.Figure 4. Single-Supply, DC-Coupled Inverting Amplifier with Negative Input VoltageFigure 6. Single-Supply, AC-Coupled Inverting AmplifierFigure 5. Dual-Supply, DC-Coupled Inverting Amplifier Figure 7. Dual-Supply, AC-Coupled Noninverting AmplifierM A X 4174/5, M A X 4274/5, M A X 4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps 14______________________________________________________________________________________Figure 9. Dual-Supply, Capacitive-Load Driving CircuitFigure 10. Small-Signal/Large-Signal Transient Response with Excessive Capacitive Load with Isolation ResistorSupply Bypassing and Board LayoutAll devices in the GainAmp family operate from a +2.5V to +5.5V single supply or from ±1.25V to ±2.75V dual supplies. For single-supply operation, bypass the power supply with a 0.1µF capacitor to ground. For dual supplies, bypass each supply to ground. Bypass with capacitors as close to the device as possible, to min-imize lead inductance and noise. A printed circuit board with a low-inductance ground plane is recommended.Capacitive-Load StabilityDriving large capacitive loads can cause instability in most low-power, rail-to-rail output amplifiers. The fixed-gain amplifiers of this GainAmp family are stable with capacitive loads up to 470pF. Stability with higher capacitive loads can be improved by adding an isolation resistor in series with the op-amp output, as shown in Figure 9. This resistor improves the circuit’s phase mar-gin by isolating the load capacitor from the amplifier’s output. In Figure 10, a 1000pF capacitor is driven with a 100Ωisolation resistor exhibiting some overshoot but no oscillation. Figures 11 and 12 show the typical small-sig-nal pulse responses of GainAmp fixed-gain amplifiers with 250pF and 470pF capacitive loads and no isolation resistor.Figure 8. Dual-Supply, DC-Coupled Noninverting Amplifier2µs/divFigure 11. MAX4174/MAX4175 Small-Signal Pulse Response (C L= 250pF, R L= 100kΩ)Figure 12. MAX4174/MAX4175 Small-Signal Pulse Response (C L= 470pF, R L= 100kΩ)2µs/divMAX4174/5, MAX4274/5, MAX4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps______________________________________________________________________________________15M A X 4174/5, M A X 4274/5, M A X 4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps 16______________________________________________________________________________________Gain Selection GuideNote:Gains in the noninverting configuration are 1+ (R F /R G ) and range from +1.25V/V to +101V/V. For a +1V/V gain, use theMAX4281/MAX4282/MAX4284.* Preferred Gains.These gain versions are available as samples and in small quantities. †The -3dB bandwidth is the same for inverting and noninverting configurations.Pin Configurations (continued)MAX4174/5, MAX4274/5, MAX4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op AmpsM A X 4174/5, M A X 4274/5, M A X 4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps 18______________________________________________________________________________________Ordering Information (continued)TRANSISTOR COUNTS:MAX4174: 178MAX4175: 178MAX4274: 332MAX4275: 332MAX4281: 178MAX4282: 332MAX4284: 328SUBSTRATE CONNECTED TO V EESelector GuideNote:Refer to Gain Selection Guide for SOT top marks.*Insert the desired gain code (from the Gain Selection Guide) in the blank to complete the part number. Refer to Gain Selection Guide for a list of preferred gains.Chip Information*Insert the desired gain code (from the Gain Selection Guide) in the blank to complete the part number.MAX4174/5, MAX4274/5, MAX4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps______________________________________________________________________________________19Package InformationM A X 4174/5, M A X 4274/5, M A X 4281/2/4SOT23, Rail-to-Rail, Fixed-Gain GainAmps/Open-Loop Op Amps Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.20____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600©1999 Maxim Integrated ProductsPrinted USAis a registered trademark of Maxim Integrated Products.Package Information。

合集下载

MAX471MAX472的中文资料大全

MAX471MAX472的中文资料大全

M A X471M A X472的中文资料大全(总4页)-本页仅作为预览文档封面，使用时请删除本页-MAX471/MAX472的特点、功能美国美信公司生产的精密高端电流检测放大器是一个系列化产品，有MAX471/MA X472、 MAX4172/MAX4173等。

它们均有一个电流输出端，可以用一个电阻来简单地实现以地为参考点的电流/电压的转换，并可工作在较宽电压内。

MAX471/MAX472具有如下特点：●具有完美的高端电流检测功能；●内含精密的内部检测电阻（MAX471）；●在工作温度范围内，其精度为2%；●具有双向检测指示，可监控充电和放电状态；●内部检测电阻和检测能力为3A，并联使用时还可扩大检测电流范围；●使用外部检测电阻可任意扩展检测电流范围（MAX472）；●最大电源电流为100μA；●关闭方式时的电流仅为5μA；●电压范围为3～36V；●采用8脚DIP/SO/STO三种封装形式。

MAX471/MAX472的引脚排列如图1所示，图2所示为其内部功能框图。

表1为MAX471/MAX472的引脚功能说明。

MAX471的电流增益比已预设为500μA/A，由于2kΩ的输出电阻（ROUT）可产生1V/A的转换，因此±3A时的满度值为3V.用不同的ROUT电阻可设置不同的满度电压。

但对于MAX471，其输出电压不应大于VRS+。

对于MAX472，则不能大于。

MAX471引脚图如图１所示，MAX472引脚图如图２所示。

MAX471/MAX472的引脚功能说明引脚名称功能MAX471MAX47211SHDN关闭端。

正常运用时连接到地。

当此端接高电平时，电源电流小于5μA2，3-RS+内部电流检测电阻电池（或电源端）。

“+”仅指示与SIGN输出有关的流动方向。

封装时已将2和3连在了一起-2空脚-3RG1增益电阻端。

通过增益设置电阻连接到电流检测电阻的电池端44GND地或电池负端55SIGN集电极开路逻辑输出端。

2SK1740-4-TB-E中文资料(sanyo)中文数据手册「EasyDatasheet - 矽搜」

2SK1740-4-TB-E中文资料(sanyo)中文数据手册「EasyDatasheet - 矽搜」

--1.5V
漏极电流ID - 毫安
--2.0V
漏 - 源电压VDS - 毫伏
--2.5V
ID -- VDS
VGS=0V
--0.5V
漏极电流ID - 毫安
--1.0V
--3.0V
--1.5V
--2.0V --2.5V
漏 - 源电压VDS - V
ID -- VGS
VDS=10V
5mA=7 SS ID5来自m4A0mA5 57至75
Ratings
Unit
min
typ
max
--40
V
--1.0 nA
--2.0
--3.0
--5.0 V
40*
75* mA
10
15
mS
22
30
mS
11
pF
2.5
pF
1.5
dB
30
本文描述或包含没有规范,能够处理应用需要极高可靠性,如生命支持系统,飞机控制系统或 其他应用程序,其故障可以合理预期会导致严重任何及所有三洋半导体产品物理和/或财产损失.请咨询 此之前,在此类应用中描述或包含usingany三洋半导体产品三洋半导体代表离你最近.
f=100MHz
通用门
--gfg
16
BFG,G12FG - 质谱
8
4
bfg
0
0
4
8
12
16
漏栅极电压,副总监 - V
ITR01970
--1.0 3
5
fs - 质3谱 y
2
4
5
7
漏电流,IDSS - 毫安
yfs -- IDSS
yfs 2(VGS=0V)
MAX5144EUB中文资料

MAX5144EUB中文资料


CS
2
SCLK 3 DIN 4
MAX5141 MAX5143
7 VDD 6 OUT 5 CLR
MAX5142 MAX5144
8 RFB 7 INV 6 OUT
DIN 4 CLR 5
µMAX
µMAX
Ordering Information
PART MAX5141EUA MAX5142EUB MAX5143EUA MAX5144EUB TEMP. RANGE -40°C to +85°C -40°C to +85°C -40°C to +85°C -40°C to +85°C PIN-PACKAGE 8 µMAX 10 µMAX 8 µMAX 10 µMAX INL (LSB) ±1 ±1 ±1 ±1 SUPPLY RANGE (V) 5 5 3 3 OUTPUT SWING Unipolar Bipolar Unipolar Bipolar
SPI and QSPI are trademarks of Motorola, Inc. MICROWIRE is a trademark of National Semiconductor Corp. ________________________________________________________________ Maxim Integrated Products 1
ELECTRICAL CHARACTERISTICS
(VDD = +3V (MAX5143/MAX5144) or +5V (MAX5141/MAX5142), VREF = +2.5V, TA = TMIN to TMAX, CL = 10pF, GND = 0, RL = ∞, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN 14 ±0.5 ±0.5 ±0.05 ±10 ±0.1 ROUT (Note 2) RFB/RINV Ratio error BZSTC PSR +2.7V ≤ VDD ≤ +3.3V (MAX5143/MAX5144) +4.5V ≤ VDD ≤ +5.5V (MAX5141/MAX5142) (Note 3) Unipolar mode Bipolar mode 2.0 10 6 15 1 7 0.2 ±0.5 ±1 ±1 VDD 6.2 1 ±0.03 ±20 ±1 ±1 ±2 TYP MAX UNITS Bits LSB LSB LSB ppm/°C LSB ppm/°C kΩ
SN74LV174APWTE4中文资料

SN74LV174APWTE4中文资料

IMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries(TI)reserve the right to make corrections,modifications,enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty.Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty.Except where mandated by government requirements,testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design.Customers are responsible for their products and applications using TI components.To minimize the risks associated with customer products and applications,customers should provide adequate design and operating safeguards.TI does not warrant or represent that any license,either express or implied,is granted under any TI patent right,copyright,mask work right,or other TI intellectual property right relating to any combination,machine,or process in which TI products or services are rmation published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement e of such information may require a license from a third party under the patents or other intellectual property of the third party,or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties,conditions,limitations,and notices.Reproduction of this information with alteration is an unfair and deceptive business practice.TI is not responsible or liable for such altered documentation.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications(such as life support)where a failure of the TI product would reasonably be expected to cause severe personal injury or death,unless officers of the parties have executed an agreement specifically governing such use.Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications,and acknowledge and agree that they are solely responsible for all legal,regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications,notwithstanding any applications-related information or support that may be provided by TI.Further,Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or"enhanced plastic."Only products designated by TI as military-grade meet military specifications.Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk,and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS16949requirements.Buyers acknowledge and agree that,if they use anynon-designated products in automotive applications,TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers Audio /audioData Converters Automotive /automotiveDSP Broadband /broadbandInterface Digital Control /digitalcontrolLogic Military /militaryPower Mgmt Optical Networking /opticalnetworkMicrocontrollers Security /securityLow Power /lpw Telephony /telephonyWirelessVideo&Imaging /videoWireless /wirelessMailing Address:Texas Instruments,Post Office Box655303,Dallas,Texas75265Copyright©2007,Texas Instruments IncorporatedPACKAGING INFORMATIONOrderable Device Status(1)PackageType PackageDrawingPins PackageQtyEco Plan(2)Lead/Ball Finish MSL Peak Temp(3)SN74LV174AD ACTIVE SOIC D1640Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ADBR ACTIVE SSOP DB162000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ADBRE4ACTIVE SSOP DB162000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ADBRG4ACTIVE SSOP DB162000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ADE4ACTIVE SOIC D1640Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ADG4ACTIVE SOIC D1640Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ADGVR ACTIVE TVSOP DGV162000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ADGVRE4ACTIVE TVSOP DGV162000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ADGVRG4ACTIVE TVSOP DGV162000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ADR ACTIVE SOIC D162500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ADRE4ACTIVE SOIC D162500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ADRG4ACTIVE SOIC D162500Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ANSR ACTIVE SO NS162000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174ANSRE4ACTIVE SO NS162000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIM SN74LV174ANSRG4ACTIVE SO NS162000TBD Call TI Call TISN74LV174APW ACTIVE TSSOP PW1690Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174APWE4ACTIVE TSSOP PW1690Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174APWG4ACTIVE TSSOP PW1690Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174APWR ACTIVE TSSOP PW162000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174APWRE4ACTIVE TSSOP PW162000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174APWRG4ACTIVE TSSOP PW162000Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174APWT ACTIVE TSSOP PW16250Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174APWTE4ACTIVE TSSOP PW16250Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIMSN74LV174APWTG4ACTIVE TSSOP PW16250Green(RoHS&no Sb/Br)CU NIPDAU Level-1-260C-UNLIM(1)The marketing status values are defined as follows:ACTIVE:Product device recommended for new designs.1-Jun-2007LIFEBUY:TI has announced that the device will be discontinued,and a lifetime-buy period is in effect.NRND:Not recommended for new designs.Device is in production to support existing customers,but TI does not recommend using this part in a new design.PREVIEW:Device has been announced but is not in production.Samples may or may not be available.OBSOLETE:TI has discontinued the production of the device.(2)Eco Plan -The planned eco-friendly classification:Pb-Free (RoHS),Pb-Free (RoHS Exempt),or Green (RoHS &no Sb/Br)-please check /productcontent for the latest availability information and additional product content details.TBD:The Pb-Free/Green conversion plan has not been defined.Pb-Free (RoHS):TI's terms "Lead-Free"or "Pb-Free"mean semiconductor products that are compatible with the current RoHS requirements for all 6substances,including the requirement that lead not exceed 0.1%by weight in homogeneous materials.Where designed to be soldered at high temperatures,TI Pb-Free products are suitable for use in specified lead-free processes.Pb-Free (RoHS Exempt):This component has a RoHS exemption for either 1)lead-based flip-chip solder bumps used between the die and package,or 2)lead-based die adhesive used between the die and leadframe.The component is otherwise considered Pb-Free (RoHS compatible)as defined above.Green (RoHS &no Sb/Br):TI defines "Green"to mean Pb-Free (RoHS compatible),and free of Bromine (Br)and Antimony (Sb)based flame retardants (Br or Sb do not exceed 0.1%by weight in homogeneous material)(3)MSL,Peak Temp.--The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications,and peak solder temperature.Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided.TI bases its knowledge and belief on information provided by third parties,and makes no representation or warranty as to the accuracy of such information.Efforts are underway to better integrate information from third parties.TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.TI and TI suppliers consider certain information to be proprietary,and thus CAS numbers and other limited information may not be available for release.In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s)at issue in this document sold by TI to Customer on an annualbasis.1-Jun-2007TAPE AND REELINFORMATIONPACKAGE MATERIALS INFORMATION19-May-2007DevicePackage Pins SiteReel Diameter (mm)Reel Width (mm)A0(mm)B0(mm)K0(mm)P1(mm)W (mm)Pin1Quadrant SN74LV174ADBR DB 16MLA 330168.2 6.6 2.51216Q1SN74LV174ADGVR DGV 16MLA 33012 6.8 4.0 1.6816Q1SN74LV174ADR D 16FMX 016 6.510.312.1216Q1SN74LV174ANSR NS 16MLA 330168.210.5 2.51216Q1SN74LV174APWRPW16MLA330127.05.61.6812Q1TAPE AND REEL BOX INFORMATIONDevice Package Pins Site Length (mm)Width (mm)Height (mm)SN74LV174ADBR DB 16MLA 342.9336.628.58SN74LV174ADGVR DGV 16MLA 338.1340.520.64SN74LV174ADR D 16FMX 342.9336.628.58SN74LV174ANSR NS 16MLA 342.9336.628.58SN74LV174APWRPW16MLA338.1340.520.6419-May-200719-May-2007IMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries(TI)reserve the right to make corrections,modifications,enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty.Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty.Except where mandated by government requirements,testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design.Customers are responsible for their products and applications using TI components.To minimize the risks associated with customer products and applications,customers should provide adequate design and operating safeguards.TI does not warrant or represent that any license,either express or implied,is granted under any TI patent right,copyright,mask work right,or other TI intellectual property right relating to any combination,machine,or process in which TI products or services are rmation published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement e of such information may require a license from a third party under the patents or other intellectual property of the third party,or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties,conditions,limitations,and notices.Reproduction of this information with alteration is an unfair and deceptive business practice.TI is not responsible or liable for such altered documentation.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications(such as life support)where a failure of the TI product would reasonably be expected to cause severe personal injury or death,unless officers of the parties have executed an agreement specifically governing such use.Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications,and acknowledge and agree that they are solely responsible for all legal,regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications,notwithstanding any applications-related information or support that may be provided by TI.Further,Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or"enhanced plastic."Only products designated by TI as military-grade meet military specifications.Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk,and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS16949requirements.Buyers acknowledge and agree that,if they use anynon-designated products in automotive applications,TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers Audio /audioData Converters Automotive /automotiveDSP Broadband /broadbandInterface Digital Control /digitalcontrolLogic Military /militaryPower Mgmt Optical Networking /opticalnetworkMicrocontrollers Security /securityRFID Telephony /telephonyLow Power /lpw Video&Imaging /videoWirelessWireless /wirelessMailing Address:Texas Instruments,Post Office Box655303,Dallas,Texas75265Copyright©2007,Texas Instruments Incorporated。