5.1.5.1 Filter specifications

IntroductionThe 25 mm High Pressure 316 Stainless Steel Filter Holder is used in laboratory applications to filter high-pressure gases or liquids for clarification/particulate removal or analysis of particulates retained on a membrane filter.WARNING: Do not use with fluids rated as dangerous substances.The pressure limit for this filter holder is 345 bar (5,000 psi) inlet, 69 bar (1,000 psi) differential.NOTE: Although this stainless steel filter holder can withstand highpressures, polymeric membrane filters are subject to compaction and flow degradation at much lower pressures. The pressure at which a given membrane filter will compact depends on its composition (polymer and backing). In general, membrane filters with smaller pore sizes (≤ 2.0 µm) can withstand higher pressure differentials (△P= P inlet - P outlet ) than membrane filters with larger pore sizes. When using polymeric membrane filters, a reduction in flow as pressure is increased indicates that the pressure is too high and that the filter should be used at a lower △P.Filter Holder AssemblySocket head cap screwsInlet plateO-ring Outlet plateFilter support screen Prefilter (optional)Filter1. Unscrew the three socket head cap screws, using the hex key supplied, if necessary.2. Remove the O-ring from the inlet plate and inspect for damage; imperfections can cause leaks during filtration. Replace if damaged. Place the O-ring back into the inlet plate O-ring groove.3. Make sure filter support screen is seated with the smooth side up in the outlet plate.4. Using smooth-tip forceps, place a 25 mm filter on top of the support screen. If using a prefilter in addition to the membrane filter, center it on top of the membrane filter.5. Place the inlet plate onto the assembly, aligning the holes of the inlet and outlet plates.6. To evenly seal the membrane, hand-tighten the screws the samenumber of turns all the way around, then tighten completely using the hex key supplied with the holder.InstallationThe 25 mm filter holder comes with ¹⁄₈ in. female national pipe thread (NPT) inlet and outlet, and can be installed with either rigid or flexible tubing. Wrap the male threads with polytetrafluoroethylene (PTFE) tape, then tighten connections with a wrench.AutoclavingNOTE: The filter holder can be autoclaved with the filter in placefor clarification/sterilization applications that do not require removing the filter intact for further use.1. Remove the holder from the in-line plumbing.2. Make sure that all inner surfaces of the filter holder are completely dry, then assemble the holder with a filter in place. Hand tighten the cap screws.3. Wrap the holder with lint-free autoclave paper, and autoclave for 15 minutes at 121 °C and 1 bar (15 psi).4. After the unit has cooled, fully tighten it with the supplied hex key, being careful not to touch the outlet port.5. Replace it in the plumbing line using aseptic technique to maintain sterility.MaintenanceClean the filter holder regularly. Frequency of cleaning will depend on the level of contamination in the fluid being filtered.1. Remove holder from plumbing system.2. Disassemble it completely and remove all PTFE wrapping from the connector threads.3. Clean all components thoroughly with a sponge, hot water, and a non-abrasive cleanser. Scrub threaded parts, recesses, and orifices with a stiff bristle brush and cleanser to remove all traces of contaminants.CAUTION: To avoid component damage, never use steel wool orabrasive materials on any part of the holder or support screens.4. Rinse all parts thoroughly with hot running tap water and then rinse with cold laboratory-grade water. Allow the components to air dry while disassembled.CAUTION: Do not wipe dry with paper or cloth, as this leavesfibers and lint on the surfaces and also generates electrostatic forces that can attract more dirt. Filtered compressed air can be used to facilitate drying.5. Replace any damaged components with EMD Millipore Corporation replacement parts. Use of parts from other manufacturers/suppliers may compromise the safety and functionality of the filter holder.User Guide25 mm High Pressure Stainless Steel Filter HolderCat. No. XX4502500The M logo, Millipore, and Durapore are registered trademarks of Merck KGaA, Darmstadt, Germany. Fluoropore and MF-Millipore are trademarks of Merck KGaA.© 2015 EMD Millipore Corporation. Billerica, MA, U.S.A. All rights reserved.20191659, Rev. 12/15SpecificationsMaximum pressure Inlet: 345 bar (5,000 psi)Differential: 69 bar (1000 psi)*Filter diameter 25 mm Prefilter diameter 25 mmEffective filter area Approximately 3.0 cm 2 (0.47 in 2)Connections Inlet and outlet: ¹⁄₈ in. female NPT Dimensions Diameter: 5.1 cm (2.0 in.)Height: 3.1 cm (1.2 in.)Weight 349 g (12.3 oz)Materials of constructionInlet and outlet plates: 316 stainless steel Filter support screen: 316 stainless steel O-ring (2-018): Buna-N rubberSocket head cap screws: 18/8 stainless steel*See note regarding membrane filter pressure differential in IntroductionTypical Filter Flow RatesFor typical flow rates and available microporous membrane filters, go to and enter the family name (Durapore, MF-Millipore, Fluoropore, etc. + membrane filters) in the search box.Statement Regarding Compliance with the Pressure Equipment Directive, 97/23/ECEMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product is classified under Article 3 § 3 of the Pressure Equipment Directive. It has been designed and manufactured in accordance with sound engineering practices to ensure safe use. The product is accompanied by user instructions and bears markings to permit identification of EMD Millipore Corporation as the manufacturer orauthorized representative of this product within the European Community. In compliance with Article 3 § 3 of the Pressure Equipment Directive, this product does not bear the CE mark.Product Ordering InformationThis section lists catalogue numbers for the 25 mm High PressureStainless Steel Filter Holder, spare parts, and accessories. See the Technical Assistance section for contact information. You can purchase these products on-line at /products.Filter Holder DescriptionCatalogue Number25 mm High Pressure Stainless Steel Filter HolderXX4502500Replacement PartsReplacement parts kit (includes socket head cap screw (3), 2-018 O-rings (3), filter support screen (1), 1/4 in. hex key (1))XX45025RKStainless steel filter support screen (1/pk)XX4502504AccessoriesFilter forceps, stainless, blunt end (3/pk)XX6200006P PTFE tape, 1.3 × 660 cm (0.5 × 260 in.) rollTP0001326NoticeThe information in this document is subject to change without notice and should not be construed as a commitment by EMD Millipore Corporation (“Millipore”) or an affiliate. Neither EMD Millipore Corporation nor any of its affiliates assumes responsibility for any errors that may appear in this document.Technical AssistanceFor more information, contact the office nearest you. In the U.S., call 1-800-221-1975. Outside the U.S., go to our web site at/offices for up-to-date worldwide contact information. You can also visit the tech service page on our web site at /techservice.Standard WarrantyThe applicable warranty for the products listed in this publication may be found at /terms (“Conditions of Sale”).。

Page 1 of 3Instruction ManualDigital Flow Switch – Integrated Display PFM7 seriesThe intended use of the digital flow sensor is to monitor and control flow and provide an output signal.These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.”They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC) *1), and other safety regulations. *1)ISO 4414: Pneumatic fluid power - General rules relating to systems. ISO 4413: Hydraulic fluid power - General rules relating to systems. IEC 60204-1: Safety of machinery - Electrical equipment of machines. (Part 1: General requirements)ISO 10218-1: Manipulating industrial robots -Safety. etc.• Refer to product catalogue, Operation Manual and Handling Precautions for SMC Products for additional information. • Keep this manual in a safe place for future reference.CautionCaution indicates a hazard with a low level of risk which, ifnot avoided, could result in minor or moderate injury.WarningWarning indicates a hazard with a medium level of riskwhich, if not avoided, could result in death or serious injury.DangerDanger indicates a hazard with a high level of risk which, ifnot avoided, will result in death or serious injury.Warning• Always ensure compliance with relevant safety laws and standards.• All work must be carried out in a safe manner by a qualified person in compliance with applicable national regulations.• This product is class A equipment intended for use in an industrial environment. There may be potential difficulties in ensuring electromagnetic compatibility in other environments due to conducted or radiated disturbances.• Refer to the operation manual on the SMC website (URL: https:// ) for more safety instructions.2.1 General specificationsItem SpecificationsE n v i r o n m e n tEnclosureIP40 Operating temperature Operating: 0 to 50 oC; Storage: -10 to 60 °C(no freezing or condensation) Humidity range 35 to 85% R.H. (no condensation)Withstand voltage 1000 VAC for 1 min.between charged part and case Insulation resistance50 MΩ min (500 VDC Mega) between charged part and caseMaterials in contact with fluidLCP, PBT, brass (electroless nickel plating),HNBR (+ fluoro coating),FKM (+ fluoro coating), Si, Au, SUS3042.2 Specifications2.3 Piping Port and Weight specificationsModel 01 02 N01 N02 F01F02C4 * C6 * C8 * N7 *Thread (Port size)Rc 1/8Rc 1/4NPT 1/8 NPT 1/4 G 1/8 G 1/4 φ4(5/32") φ6φ8(5/16")φ1/4W e i g h tStraight95 g(without flow adjustment valve)125 g 55 g Bottom entry 105 g (without flow adjustment valve)135 g 65 g Straight135 g(with flow adjustment valve)165 g 95 g Bottom entry 145 g (with flow adjustment valve)175 g105 g* Indicates one touch fitting.2.4 Cable specifications ConductorNominal cross section AWG26 Individual wire diameter approx. 0.50 mm InsulatorOutside diameter approx. 1.00 mm Colours Brown, White, Black, Blue SheathMaterial Lead free heat and oil resistant PVC Outer diameterapprox. φ3.5 mmWarning• Special products (-X) might have specifications different from those shown in this section. Contact SMC for specific drawings.2.5 Analogue Output characteristics∗: Analogue output at maximum rated flow rate when CO 2 is selected is 3 [V] for the voltage output type and 12 [mA] for the current output type.Model Max. rated flow (L/min) Model Max. rated flow (L/min) PFM710-#-C/E 10 (5) PFM710-#-D/F 10 (5) PFM725-#-C/E 25 (12.5) PFM725-#-D/F 25 (12.5) PFM750-#-C/E 50 (25) PFM750-#-D/F 50 (25) PFM711-#-C/E100 (50)PFM711-#-D/F100 (50)∗: Values for CO 2 shown in brackets ( ).∗: The table shows the specifications when a flow adjusting valve is included.4 Installation4.1 InstallationWarning• Do not install the product unless the safety instructions have been read and understood.• Use the product within the specified operating rated flow, operating pressure and temperature range.• Tighten to the specified tightening torque.If the tightening torque is exceeded the mounting screws, brackets and the product can be broken. Insufficient torque can cause displacement of the product from its correct position.• Do not drop, hit or apply excessive shock to the product.ORIGINAL INSTRUCTIONSItemDescription Indicator LED (OUT1)Indicates the output status of OUT1.LED is ON (Green) when OUT1 is ON.When the accumulated pulse output mode is selected, the indicator LED will turn OFF. Indicator LED (OUT2)Indicates the output status of OUT2. LED is ON (Red) when OUT2 is ON. When the accumulated pulse output mode is selected, the indicator LED will turn OFF. SET buttonPress this button to change to another mode and to set a value. SocketSocket for electrical connections. Piping portConnected to the fluid inlet at IN side and to thefluid outlet at OUT side.LED displayDisplays the flow value, setting mode, and errorindication. Four display modes can be selected: display always in red or green, or display changing from green to red, or red to green, according to the output status (OUT1).UP button Selects the mode or increases the ON/OFF set value. Press this button to change to the peak display mode.DOWNbutton Selects the mode or decreases the ON/OFF setvalue. Press this button to change to the bottom display mode.Flow adjustmentvalve. Orifice mechanism to adjust the flow.Lock ring Used to lock the flow adjustment valve. Mounting hole Used to mount the product on a DIN rail ordirectly to a panel.BodyThe body of the product. Lead wire and connector Lead wire to supply power and transmit output signals.∗: The table shows the specifications when a flow adjusting valve is included.Page 2 of 34.2 EnvironmentWarning• Do not use in an environment where corrosive gases, chemicals, salt water or steam are present.• Do not use in an explosive atmosphere.• Do not expose to direct sunlight. Use a suitable protective cover.• Do not install in a location subject to vibration or impact in excess of the product’s specifications.• Do not mount in a location exposed to radiant heat that would result in temperatures in excess of the product’s specifications.4.3 Mounting• Never mount the product in a location that will be used as a foothold. • Mount the product so that the fluid flows in the direction indicated by the arrow on the body.4.3.1 Panel mounting• Insert Panel Mount Adapter B (supplied as an accessory) into Section A of Panel Mount Adapter A.Push Panel Mount Adapter B from behind until the display is located in the panel.The pin of Panel Mount Adapter B engages the notched part of Panel Adapter section C to fix the display.• The switch can be mounted on a panel with a thickness of 1 to 3.2 mm.4.3.2 Bracket mounting• Mount the bracket (Part No. ZS-36-A1) on to the product using the mounting screws supplied.• The required tightening torque is 0.5 ±0.05 N•m. Without Flow adjustment valve With Flow adjustment valve(using Part No. ZS-33-M)(using Part No. ZS-33-MS)• Install the product (with bracket) using M3 screws (4 pcs.). • Bracket thickness is approximately 1.2 mm.Refer to the operation manual on the SMC website (URL: https:// ) for mounting hole dimensions.4.3.3 DIN rail mounting• Mount the DIN rail brackets (Part No. ZS-33-R#) to the product using the mounting screws and joint screws supplied.• The required tightening torque for both screw types is 0.4 ± 0.05 N•m.4.4 PipingCaution• Before connecting piping make sure to clean up chips, cutting oil, dust etc.• When installing piping or fittings, ensure sealant material (tape) does not enter inside the port.• When connecting the piping, hold the specified part of the body with a spanner. Using a spanner on other parts may damage the product. • The required tightening torque of the fittings is given in the table below. If the tightening torque is exceeded, the product can be damaged. If the correct tightening torque is not applied, the fittings may become loose.• Ensure there is no leakage after piping.Nominal Thread size Width across flats ofattachmentTightening torqueRc (NPT) 1/8, G1/8 Rc (NPT) 1/4 17 mm7 to 9 N•m G1/421 mm12 to 14 N•m4.4.1 One Touch fittings• Insert the tube until it bottoms out, to ensure it cannot be pulled out. • Insertion with excessive force can cause damage. • Ensure that there is no leakage after piping.• Use the product within the specified operating pressure and temperature ranges.• Proof pressure is 1.0 MPa.5.1 WiringCaution• Wiring should only be performed with the power supply turned OFF. • Confirm proper insulation of wiring.• Use separate routes for the product wiring and any power or highvoltage wiring. Otherwise, malfunction may result due to noise.• Keep wiring as short as possible to prevent interference from electromagnetic noise and surge voltage.• Ensure that the FG terminal is connected to ground when using a commercially available switch-mode power supply.Switching noise will be superimposed and the product specification can no longer be met. This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply.5.1.1 Connecting/Disconnecting• When mounting the connector, insert it straight into the socket, holding the lever and connector body, and push the connector until the lever hooks into the housing, and locks.• When removing the connector, press down the lever to release the hook from the housing and pull the connector straight out.5.1.2 Connector pin numbers (on the lead wire)6 Flow Setting6.1 Measurement mode• Measurement mode is the mode in which the flow is detected and displayed, and the switch function is operating.• This is the basic operating mode; other modes should be selected for set-point and other Function Setting changes.6.2 Switch operation• When the flow exceeds the set value, the switch will turn ON.• When the flow falls below the set value by the amount of hysteresis or more, the switch will turn OFF.• If this condition, shown to the right, is acceptable, then keep these settings.<Operation>∗: The Product outputs will continue operating during setting.1. Press the SET button in measurement mode to display the set values.[P_1] or [n_1] and the set value are displayed in turn.2. Press the UP or DOWN button to change the set value.The UP button is to increase and the DOWN button to decrease the set value.Press the UP button once to increase by one digit or press it continuously to keep increasing the set value.Press the DOWN button once to decrease by one digit or press it continuously to keep decreasing the set value.3. Press the SET button to finish the setting of OUT1.For models with 2 outputs, [P_2] or [n_2] will be displayed. Set OUT2 as above.• Zero clear of displayThe display is reset to zero when UP and DOWN are pressed simultaneously for 1 second.For the initial operation, always perform zero clear with no flow applied.Page 3 of 37.1 Function selection modeIn measurement mode, press the SET button for 2 seconds or longer to display [F 0].The [F##] indicates the mode for changing each function setting.Press the SET button for 2 seconds or longer in function selection mode to return to measurement mode.• Peak / Bottom hold function • Zero clear function • Key-lock functionRefer to the operation manual on the SMC website (URL: https:// ) for setting these functions.Refer to the operation manual or catalogue on the SMC website (URL: https:// ) for How to order information.Refer to the operation manual or catalogue on the SMC website (URL: https:// ) for Outline Dimensions.11.1 General MaintenanceCaution• Not following proper maintenance procedures could cause the product to malfunction and lead to equipment damage.• If handled improperly, compressed air can be dangerous.• Maintenance of pneumatic systems should be performed only by qualified personnel.• Before performing maintenance, turn off the power supply and be sure to cut off the supply pressure. Confirm that the air is released to atmosphere.• After installation and maintenance, apply operating pressure and power to the equipment and perform appropriate functional and leakage tests to make sure the equipment is installed correctly.• If any electrical connections are disturbed during maintenance, ensure they are reconnected correctly and safety checks are carried out as required to ensure continued compliance with applicable national regulations.• Do not make any modification to the product.• Do not disassemble the product, unless required by installation or maintenance instructions.• How to reset the product after a power cut or when the power has been unexpectedly removedThe settings of the product are retained from before the power cut or de-energizing.The output condition also recovers to that before the power cut or de-energizing, but may change depending on the operating environment. Therefore, check the safety of the whole system before operating the product.12 Limitations of Use12.1 Limited warranty and Disclaimer/Compliance Requirements Refer to Handling Precautions for SMC Products.13 Product disposalThis product should not be disposed of as municipal waste. Check your local regulations and guidelines to dispose of this product correctly, in order to reduce the impact on human health and the environment.14 ContactsRefer to or www.smc.eu for your local distributor / importer.URL: https:// (Global) https:// (Europe) SMC Corporation, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, Japan Specifications are subject to change without prior notice from the manufacturer. © 2021 SMC Corporation All Rights Reserved. Template DKP50047-F-085MItemDefault setting[F 0] [Uni] Unit selection function[ L] L/min[F 1] [oU1] Output mode (OUT1) [HYS] Hysteresis mode [1ot] Reversed output (OUT1)[1_P] Normal output[P_1] Input Set value (OUT1) [ ] 50% of max. rated flowPFM710: 5 L/min,PFM725: 12.5 L/min PFM750: 25 L/min,PFM711: 50 L/min[H_1] Hysteresis Setting(OUT1) [ ] 3% of max. rated flow PFM710: 0.3 L/min,PFM725: 0.8 L/minPFM750: 1.5 L/min,PFM711: 3 L/min [CoL] Display colour [SoG] ON: Green, OFF: Red[F 2][oU2] Output mode (OUT2) [HYS] Hysteresis mode[2ot] Reversed output(OUT2) [2_P] Normal output[P_2] Input Set value (OUT2) [ ] 50% of max. rated flow PFM710: 5 L/min, PFM725: 12.5 L/min PFM750: 25 L/min, PFM711: 50 L/min[H_2] Hysteresis Setting(OUT2)[ ] 3% of max. rated flowPFM710: 0.3 L/min,PFM725: 0.8 L/min PFM750: 1.5 L/min,PFM711: 3 L/min[F 3] [FLU] Operating fluid [A i r ] d ry air, N 2[F 4] [rEF] Reference condition [A nr] Standard condition[F 5] [eES] Response time[1.00] 1 second [F 6] [dSP] Display mode [i nS ] Instantaneous flow [F 7] [inP] External input [r _r ] Accumulated flowexternal reset [F 8] [drE] Display resolution [1E2] 100-split[F 9] [PrS] Auto-preset[oFF] Manual [F10] [EEP] Accumulated hold [oFF] OFF [F11] [AFL] Analogue output filter [ on] With filter [F12] [Eco] Power saving mode [oFF] Unused [F13] [Pin] Security code [oFF] Unused [F98] [ALL] Setting of all functions [oFF] Unused[F99] [ini] Reset to default settings [oFF] Unused。

Capture the perfect shot with the Sony® DCR-SR67 Handycam® camcorder. A built-in 80GB hard diskdrive offers extended, hassle-free recording and a professional-quality Carl Zeiss® Vario-Tessar® lens delivers sharp, high resolution images and a powerful 60x optical zoom. Hybrid technology even allows you to record video to the hard drive or optional Memory Stick Duo™ media.180GB hard disk drive:A built-in 80GB hard disk drive can record and store up to 56 hours of video footage in SD LP mode. Inaddition, “HDD Smart Protection” gives you peace of mind by preventing any recorded video and images from being lost if the camcorder is accidentally dropped.1 60X Optical / 2000X Digital Zoom:Ideal for sporting events, wildlife, or distance shooting, 60X optical zoom brings you closer to the action, so you can capture extremely tight shots, even from far away. In addition, DigitalZoom Interpolation means that extreme digital zooming (up to 2000X) is clearer, with less distortion than previous types of digital zooms.Carl Zeiss® Vario-Tessar® lens with SteadyShot™ image stabilization: The DCR-SR67 features a professional-quality Carl Zeiss® Vario-Tessar® lens designed specifically for compact camcorders. Precision ground optics help maintain the sharpness and contrast of larger lenses, andSteadyShot™ image stabilization helps reduce blur caused by camera shake.Hybrid Recording to HDD or Memory Stick Duo™ media:Hybrid recording technology delivers a new level of flexibility of capturing andtransferring your video footage anddigital photos from the camcorder to compatible viewing devices. Record to 80GB hard disk drive or choose instead to record to removableMemory Stick PRO Duo™ media (sold separately). You can even select from various dubbing functions to easily copy video or still images from the HDD to the Memory Stick® media -- without using a PC.1 1/8” Advanced HAD™ CCD Imager: A 1/8” Advanced HAD™ (HoleAccumulation Diode) CCD imager with 410K (effective) pixel resolution delivers stunning detail and clarity forexceptional video and still image performance.Direct connection with DVD burner (sold separately):The DCR-SR67 supports a directconnection to the VRD-P1 DVD burner (sold separately), which allows you to burn DVDs directly from yourcamcorder without the need for a PC. And because the VRD-P1 is powered by your camcorder, you don't need an additional AC power cable.2.7” wide touch panel LCD display (123k pixels):The 2.7" wide touch panel LCD display provides exceptional viewing clarity with 123K pixels resolution. The display rotates up to 270 degrees for multiple viewing angles, as well as provides sharp, detailed images for monitoring or playback. The convenient touch panel allows easy access to menus and additional functionality such as spot focus and spot metering.3 3 Power On by opening LCD display:Power on your camcorder by simply opening the LCD display.Dolby® Digital 5.1ch recording with Built-in Zoom Mic:Dolby® Digital 5.1 channel recording captures active sounds coming from all directions, so you can experience your home movies the way you experiencedthem while recording. The Built-In Zoom Mic focuses audio recording on your subjects in sync with the camera’s zoomlens.Includes Sony® PMB (Picture MotionBrowser) software:Sony Picture Motion Browser software offers a simple, intuitive way to transfer, sort, and view your video and still images on your compatible PC. In addition, multiple output options let you burn your memories to DVD (sold separately), as well as take advantage of one click upload to a number of popular video and photo sharing sites .9 Record and zoom controls on LCD frame:The DCR-SR67 features an additional set of record and zoom buttons on theframe of the LCD screen, give you more control and flexibility when holding the camcorder, especially in overhead or low angle shots.One Touch Disc Burn:Easily burn a DVD copy of yourfootage using the supplied PMB (Picture Motion Browser) software . Simply connect the camcorder to yourcompatible PC via a USB cable and press the One Touch Disc Burn Button.9 12 Easy Handycam® Button:Using a camcorder can be intimidating for some people. With a press of the Easy Handycam Button, most of the advanced features of the camcorder are "locked out," letting you focus only the buttons essential for recording.Film Roll Index:Like chapters in a book, Film Roll Index helps you easily find desired scenes in video footage. When using this feature, the camcorder previews the beginning of scenes and can create scene indexes set at specified display intervals (3, 6, or 12 seconds and 1 or 5 minutes).ADDITIONAL FEATURES Face Index function:USB 2.0 interface:Sony Electronics Inc. • 16530 Via Esprillo • S an Diego, CA 92127 • 1.800.222.7669 • w Last Updated: 02/10/20091. 80GB available. Storage capacity may vary. A portion of the memory is used for data management functions.3. Viewable area measured diagonally.9. Requires Windows 2000 Professional SP4, Windows XP SP2, or Windows Vista. Not supported by Mac OS.12. One Touch Disc Burn feature requires DVDirect burner or compatible PC with supplied PMB software (sold separately). © 2008 Sony Electronics Inc. All rights reserved. Reproduction in whole or in part without written permission is prohibited. Sony, Handycam, Advanced HAD, Memory Stick, Memory Stick Duo,Memory Stick PRO Duo, DVDirect and SteadyShot are trademarks of Sony. Windows, and Windows Vista are registered trademarks of Microsoft Corporation. All other trademarks are trademarks of their respective owners.*Logo mentions need to be included if logo shown or listed in copyPlease visit the Dealer Network for more information at/dn SpecificationsGeneralImaging Device: 1/8" Advanced HAD™ CCDsensor Pixel Gross: 680KRecording Media: 80GB Non-Removeable Hard Disk DriveMemory Stick PRO Duo Media (Sold Separately) Recording and Playback Times: StandardDefinition: HQ = up to 1180 min., SP = up to 1750 min., LP = up to 3360 min.When using 16GB Memory Stick PRO Duo® Media (sold separately): StandardDefinition: HQ = up to 230 min., SP = up to 340 min., LP = up to 655 min. Video Actual: 410K pixels (16:9), 340K pixels (4:3) Still Actual: 250K pixels (16:9), 340K pixels (4:3)Video Resolution: 720 x 480Still Picture Resolution: 680KAudioRecording Format: Dolby® Digital 5.1Microphone: Built-in Zoom MicrophoneConvenienceMemory Stick PRO™ Media Compatibility: Memory Stick PRO Duo Media (Sold Separately) Still Image Mode(s): JPEGHybrid: YesConvenience FeaturesMultiple Language Display: YesSlide Show Mode: YesScene Mode(s): Auto, Twilight, Twilight Portrait, Candle, Sunrise & Sunset,Fireworks, Landscape, Portrait, Spotlight, Sports, Beach, Snow Fader Effect(s): Black, WhiteFace Index: YesFilm Roll Index: YesPhoto Capture from Movie: YesSteadyShot® Image Stabilization: SteadyShot™ image stabilizationWhite Balance: Auto / outdoor / indoor / Onepush (Touch Panel)VideoFormat: SD (MPEG2)Video Signal: NTSC color, EIA standardsInputs and OutputsAnalog Audio/Video Output(s): Included (via A/V Remote Terminal) USB Port(s): Hi-speed (2.0 compliant)S-Video Output(s): Sold separately (via A/V Remote jack) Audio/Video Remote Terminal: Video / S Video / AudioDisplayLCD Screen: 2.7” wide touch panel LCD display (123k pixels)HardwareMemory Stick slot: Memory Stick PRO Duo Media Manual / Auto Lens Cover: ManualS/S & Zoom button on LCD: YesOptics/Lens35mm Equivalent: 39-2340mm (16:9), 44-2640mm (4:3)Aperture: F1.8-6.0Exposure: Yes (Touch Panel)Filter Diameter: 30mmFocal Distance: 1.8 - 108mmFocus: Full range Auto / Manual (Touch Panel) Shutter Speed: Auto, 1/4 - 1/4000 (Scene Selection Mode) Optical Zoom: 60xDigital Zoom: 2000xResolution: 680KLens Type: Carl Zeiss® Vario-Tessar®Minimum Illumination: 6 lux(Auto Slow Shutter On, 1/30 Shutter Speed )PowerPower Consumption: 2.2WBattery Type: InfoLITHIUM® with AccuPower™ Meter System (NP-FH30) Power Requirements: 7.2V (battery pack); 8.4V (AC Adaptor)Service and Warranty InformationLimited Warranty Term: Limited Warranty --- 1 Year Parts; 90 Days LaborSoftwareOperating System Compatibility: Windows 2000 Professional SP4/Windows XP SP2* /Windows Vista * *1 64-bit editions and Starter (Edition) are not supported.Standard installation is required. Operation is not assured if the above OS has been upgraded or in a multi-boot environment. Supplied Software: PMB Ver.4.2.00 Supports Windows 2000 Professional Service Pack4 (SP4), Windows XP Service Pack3 (SP3)(32bit)Windows Vista Service Pack1 (SP1)(32bit/64bit). Not supported by Mac OSDimensionsWeight: 10oz (300g)Measurements: 2 3/8 x 2 3/4 x 4 1/2 inch (60 x 68 x 112mm)Supplied AccessoriesAC adaptor (AC-L200)Rechargable Battery Pack (NP-FH30)A/V Connecting CableClock Lithium (Installed) (ML621/MS621FE)Application Software / USB Driver / (CD-ROM)USB CableOptional AccessoriesRechargeable InfoLITHIUM Batteries (NP-FH50/FH70/FH100 Case (LCS-BBDB/R/L, LCS-AJA)Starter Kit (ACC-ASH6)AC Adaptor/Charger for H series batteries (AC-VQH10) Travel Charger (BC-TRP)Wide Angle Conversion Lens (VCL-HGE07A)Tripod (VCT-80AV)Video Light (HVL-10NH)Underwater Sports Pack (SPK-HCE)GPS Unit (GPS-CS3KA)UPC Code: 027*********。

5. 145kV CABLE PARTICULAR SPECIFICATIONS5.1. THE ELECTRICAL CONDUCTOR5.1.1. The electrical conductor must be compressed circular, stringing class 2,according to IEC 60228 or segmented, with blocked gaps.导线符合IEC60228标准5.2. C ONDUCTOR SHIELDThe physical characteristics of the semiconductive shield must agree with IEC 60840 standard requirements related to the cable voltage.The average thickness of the extruded layer must be equal to or greater than 1,5mm and the minimum thickness at any point of the cross-section must not be less than 1,35mm. The eccentricity must agree with IEC 60840 standard requirements related to the cable voltage.导体屏蔽标准IEC60840，挤压层平均厚度1.5mm，横截面最小厚度不低于1.35mm，5.3. C ONDUCTOR INSULATION5.3.1. Physical RequirementsThe physical characteristics of insulation material must agree with IEC 60840 standard requirements related to the cable voltage for EPR and XLPE insulation.EPR（乙烯丙烯共聚物）和XLPE（交联聚乙烯）绝缘The thickness of insulation must be defined by the manufacturer and its efficiency must be verified by type test according to IEC 60840 standard requirements related to the cable voltage.The minimum insulation thickness and eccentricity at any point of the cross-section must not be less or lower than 90% of the specified rated value.5.4. S EMICONDUCTIVE SHIELD ON THE INSULATION5.4.1. The physical characteristics of semiconductive shield on the i nsulationmust agree with IEC 60840 standard requirements related to the cable voltage.5.4.2. The semiconductive shield on insulation must be tight and continuouslyadhered to it.5.4.3. After the semiconductive shield withdraw, the insulation exposed surfacemust be undamaged and must not present any semiconductor material of difficult removal.5.4.4. The average thickness of the extruded layer must equal to or greaterthan 1,5mm, considering copper wire or lead plate shield and the minimum thickness at any point of the cross-section must not be less than 1,35mm.The eccentricity must agree with IEC 60840 standard requirements related to the cable voltage.5.5. M ETALIC SHIELD金属屏蔽5.5.1. Copper wire shield铜线屏蔽This type of shield must be constituted of copper wires with resistivity not exceeding 0,017241 ohms x mm² / metro a 20°C uniformly arranged over the semiconductive surface of insulation and it must not break when the cable is curved with a minimum radius equal to 20 times the rated external diameter of the cable.由铜线构成，这20℃下电阻系数不超过0.017241 ohms x mm2/ metroMust be provided the blockade against longitudinal water penetration between the semiconductive shield and the metallic layer which must agree with IEC 60840 standard requirements.5.5.2. Metallic layer金属层If the shield is constituted by a metallic layer, it must be made of continuously extruded lead.金属层为铅The minimum average thickness of the metallic layer must be compatible with the mono-phase short circuit current, informed in the basic specification and the minimum thickness at any point of the cross-section must not be less than 2,9mm. In this case, the cooper wire shield may be unnecessary depending on the phase-to-ground short-circuit current.横截面厚度不低于2.9mmAlternatively, the metallic layer may be constituted by a longitudinal aluminum strip and firmly adhered to the external jacket of the cable and overlapping length sufficient to serve as a cross barrier to the penetration of moisture.或者为铝Other type of protection (against: moisture, chemicals, bugs etc…) may be implemented according to data in the basic specification.5.6. C OVERAGEThe physical characteristics of polyethylene material coverage must agree with IEC 60840 standard requirements related to the operating temperature for the cable, considering material ST 7 (which defines the material that must be used for each operating temperature).The rated thickness of the polyethylene coverage must be greater than 3,4mm at any point of the cable.电缆聚乙烯厚度必须超过3.4mmThe average thickness of the coverage at any point must not be less than the rated value and the minimum thickness at any point of cross-section must not be less than the value indicated at IEC 60840.5.7. E LECTRIC RESITANCEThe conductor’s electrical resistance referred to 20°C and 1km must agree with the requirements of IEC 60228 standard requirements.20℃下电阻轮率应符合IEC60228标准5.7.1. Partial DischargeThe cable, when submitted to AC voltage, with operating value of 1,75 U0 during 10 seconds and slowly reduced to 1,50U0 must not have partial discharge level exceeding 5pC and 10pC, at the latest voltage (1,50 U0) for type and routine tests respectively.The test must be done according to IEC 60885-3 standard specifications.5.8. Q UANTITY- 06 parts of 200m (total 1200m) of145kV cable with terminals crimped at both ends.NOTE: To calculate the wire size consider power transformer of 40MVA and short-circuit current equal to 40kA / 0.5 seconds.。

Key Features1” Exmor R ® CMOS sensor w/ Direct Pixel Read OutThe world’s first 1.0” CMOS sensor featuring an Exmor R ® CMOS image sensor technology. With this back-illuminated technology, the sensor doubles light sensitivity and combines with Sony’s Column A/D Conversion to reduce noise by half — a great help when photographing in dimly lit environments. Markedly reduced noise is evident even when high-sensitivity settings are used for capturing night landscapes or indoor scenes.14MP resolution video and 20MP still image captureCreate cinematic video with 14MP resolution sensor (for video) and high quality 20MP still images.Versatile shooting w/ XA VC-S, A VCHD and MP4 codecsThe HDR-CX900 records HD movies in the XA VC-S format, which uses MPEG-4 A VC/H.264 for video compression and linear PCM for audio compression, while saving files in a MP42 wrapper. The highly compressed files allow extensive record times. The camcorder also records in A VCHD, ideal for quality video for HDTV and Blu-ray disc burning. Additionally, the camcorder can shoot MP4 HD video, which is ideal for sharing over the internet at up to 28Mbps. Having the ability to switch between all three of three formats makes this camcorder an ideal tool that is versatile for creating content to live in a number of different environments.Carl Zeiss ® Vario Sonnar T* lens w/ 12x optical zoomThe HDR-CX900 comes equipped with a newly developed Carl Zeiss ® Vario-Sonnar T* lens that has cleared a series of tough performance tests. Not only is this 29mm wide-angle lens ideal for capturing grand landscapes, but it covers wide-ranging image expression thanks to maximum 12x optical zoom and 24x Clear Image zoomMulti-interface Accessory Shoe for system accessoriesUsers can expand photographic and movie shooting possibilities by attaching optional accessories via the Multi Interface Shoe, including an electronic viewfinder, powerful external flash and stereo microphone. You can also connect with a compatible remote control via Multi Terminal.BIONZ ® X Processor enables high Speed rec 120fpsThe new BIONZ ® X image processor enables the camcorder to create more naturally vivid and lifelike image quality, and higher resolution imagery.Notable features of BIONZ X technology include:1. Detail reproduction technology optimally filters edges and textures differently depending on the scene.2. Area specific noise reduction swiftly and efficiently analyzes the subject and reduces noise.This new image processing technology achieves an even better balance of exceptional detail and advanced noise control.Its ability to record at 120p enables slow-motion playback at one-fifth the speed in a 24p environment in post-processing.Optical SteadyShot™ Image Stabilization w/ Active ModeHDR-CX900/BHD Camcorder with 1" sensorWelcome to broadcast-quality HD video from the palm of your hand. The 1” image sensor is approximately 8x larger than that of typical camcorders for capturing defocused backgrounds and true cinematic depth. It’s flexible, too. Record your vision in XA VCS (up to 50mpbs), A VCHD or MP4 codecs with impressive clarity and color accuracy. There’s nothing else like it in the industry.Optical SteadyShot™ Image Stabilization with Intelligent Active Mode is an advanced optical image stabilization technology that corrects camera shake to capture scenes with phenomenal smoothness and stability. Intelligent Active Mode analyzes video frames and provides compensation with assistance from the new BIONZ® X image processing engine. Whether recording movies while strolling on vacation, shooting while chasing a child, or zooming in to capture faraway subjects, Handycam’s simple solution smoothly reproduces the scene with a higher level of stability.High contrast 0.39" OLED EVF for eye-level framingThe HDR-CX900 employs high contrast a 0.39” OLED Tru-Finder EVF which reproduces rich color and deep black. A new optical design of the EVF, using four dual-surface aspherical lenses, allows for a 33-degree wide angle view that is amazing clear through the edge of the view finder. Large 3.5" Xtra Fine LCD™ (921K)The 3.5” (16:9) Xtra Fine LCD™ screen (921K) displays sharp, bright, vivid images, letting you compose a shot more easily -- even outdoors, while enabling you to change settings to best represent the scene.Simple connectivity to smartphones via Wi-Fi®/NFCConnectivity with smartphones for One-touch sharing/One-touch remote has been simplified with Wi-Fi®/NFC control. In addition to Wi-Fi® support for connecting to smartphones, the HDR-CX900 also supports NFC (near field communication) providing “touch connection” convenience when transferring images to Android™ smartphones and tablets. Users need only touch devices to connect; no complex set-up is required. Moreover, when using Smart Remote Control — a feature that allows shutter release to be controlled by a smartphone — connection between HDR-CX900 and the smartphone can be established by simply touching devices.Specifications1. Requires NFC-compatible mobile device. Check device’s user manual for compatibility.© 2014 Sony Electronics Inc. All rights reserved. Reproduction in whole or in part without written permission is prohibited. Sony, Exmor R, BIONZ and the Sony logo are trademarks of Sony Corporation. All other trademarks are trademarks of their respective owners. Features and specifications subject to change without notice. / UPC:027********* / Updated: January 3, 2014。

PRELIM The Sony® Cyber-shot® DSC-HX1 camera with Exmor™ CMOS technology offers up to 10fps shooting and features Sweep Panoramamode – that can seamlessly combine multiple shots to produce striking images, advance modes that reduce noise by approximately 50% even in difficult shooting situations, as well as 1080p movie recording6. Additionally it features professional quality 20x wide angle G-lens, 3” titable LCD and Intelligent Auto mode19.1 Megapixel Super Exmor™ CMOS Image Sensor:The HX1 features a 9.1 megapixel Exmor™ CMOS image sensor thatbrings out the full resolving power of the camera’s precision G-Lens to deliver extremely fast speed, high resolution, and stunning low-light sensitivity with improved image clarity and drastically reduced noise. With 9.1 megapixels, you can create stunning, photo-quality prints up to A3+ (13x19”) size, or crop your images and still come away with high resolution shots.Professional Quality G-Lens:Designed and manufactured to the highest standards of optical performance, the Sony G-Lens isoptimized to perfectly complement the advanced image sensors and image processing technology in Sony’scameras. G lenses are used in top of the line digital single lens reflex (DSLR)cameras and advanced pro-sumer HD Camcorders. Capture the action up close with the 20x optical zoom, and with the 28mm wide angle lens the HX1 even allows you to capture more of the scenes in landscape or group portraits. The HX1’s G Lens has a six blade aperture capable of producing abeautiful bokeh (beautifully defocused backgrounds with a soft natural feel). The aspherical lens elements made from ED (extra-low dispersion) minimize chromatic aberration common to high-magnification lenses.20x High Zoom:20x optical zoom extends your reach and helps bring you closer to the action – a real benefit for sporting events, wildlife, distant landscape views and dramatic portrait shots.28mm Wide Angle Lens:Widen your view and capture more of the city, landscape, or group with a 28mm wide angle G lens.3.0" Clear Photo LCD™ tilt display (230k pixels):Compose and show off your images on the large 3.0”(230K) Clear Photo LCD Plus™ display, which tilts up or down approximately 90 degrees for easier high and low angle shooting and features a special anti-reflective coating for sharp visibility, even in bright sunlight.1 CMOS Sensor:Enjoy extremely high resolution, fine tonal gradation and fast speed that faithfully reproduces every detail of your subject and reduces visual noise. The Exmor™ CMOS sensor brings out the full potential of the lens to ensure clear, high-precession image quality.BIONZ™ image processor:The BIONZ™ image processor delivers the high resolution and fastperformance you expect from a Sony® digital camera.Colors available in:The Cyber-shot® DSC-HX1 camera is available in black.High Speed Shooting (10fps):The HX1 is the world’s first digital still camera that can capture full 9.1megapixel resolution images at up to 10 fps, helping to ensure you never miss the decisive moment. What’s more, the HX1 employs a mechanical shutter that helps reduce distortion whencontinuously shooting moving subjects.ADDITIONAL FEATURESSweep Panorama Mode:Handheld Twilight Mode:Anti-Motion Blur Mode: HD Movie (1080p):Intelligent Auto Mode:Intelligent Scene Recognition:Face Detection technology:Selected Face Memory:Anti-blink Function: Red-eye Reduction:Smile Shutter™ Technology: Double Anti-blur Solution:Optical SteadyShot™ Image Stabilization:High Sensitivity Mode (ISO 3200):Dynamic Range Optimizer Standard and Plus:Convenient Photo Modes:9-Point Auto Focus:Function Guide:Intelligent Auto Focus:Functional Button Layout:Simplified Buttons:Easy Shooting Mode:16:9 High Resolution Mode:Memory Stick Duo™ Media Convenience:Stamina® Battery Power:Easy Image Management:HDTV Compatibility:BRAVIA® Sync™: PhotoTV HD:Wide Zoom tilt display:PHOTOMUSIC feature:In-Camera Retouching Tools: Multi-purpose Resize function: Picture Motion Browser ver. 4.2.02:Sony Electronics Inc. • 16530 Via Esprillo • S an Diego, CA 92127 • 1.800.222.7669 • w Last Updated: 07/21/2009Please visit the Dealer Network for more information at /dnSpecificationsGeneralMegapixel: 9.1 MPImaging Device: 1/2.4 type(7.63mm) Exmor CMOS SensorRecording Media: 11MB internal Flash Memory, optional Memory Stick Duo™ Media, optional Memory Stick PRO Duo™ MediaConvenienceWhite Balance: Auto / Daylight / Cloudy / Fluorescent 1 (White Fluorescent Lighting) / Fluorescent 2 (Natural White FluorescentLighting) / Fluorescent 3 (Day White Fluorescent Lighting) / Incandescent / Flash / Underwater White Balance Mode - Auto, Underwater 1, Underwater 2, FlashSelf Timer: Yes (10 seconds, 2 seconds, Off)Memory Stick PRO™ Media Compatibility: Tested to support up to 16GB Memory Stick DUO PRO™ media capacity ; does not support Access Control security function.Still Image Mode(s): Normal/High Speed Burst (High/Med/Low)/Bracketing(JPEG)-AE (Plus/Minus0.3EV/0.7EV/1.0EV)/WB/ColorRed-Eye Reduction: Auto / On / OffBurst Mode: Approx 10 fps (10 shots)Date/Time Stamp: Available in the included PMB software.Media/Battery Indicator: Yes/YesColor Mode(s): Normal / Vivid / Sepia / B&W / RealDynamic Range Optimizer: Standard / Off / PlusScene Mode(s): iAuto, Easy, Program, Handheld Twilight, Anti-Motion Blur, Sweep Panorama, Manual Exposure, Aperture Priority, ShutterSpeed Priority and Scene Selection such asHigh Sensitivity, Landscape, Soft Snap,Advanced Sports Shooting, Twilight Portrait, Twilight, Beach, Snow, Fireworks, and GourmetImage Stabilization: OpticalConvenience FeaturesHistogram Display: YesReal Imaging Processor™ Technology: BIONZ™AF Illuminator Light: Auto / OffPictBridge Compatible: YesMulti-Pattern Measuring: YesNightShot® Infrared System: NoNightFraming System: NoClear RAW NR: YesMovie Mode(s): 1280 x 720(Standard) (Approx.30fps, Progressive) / 1280 x 720(Approx.30fps, Progressive) / 1440 x 1080(Fine) (Approx.30fps, Progressive) / 1440 x 1080(Standard) (Approx.30fps, Progressive) / VGA (640 x 480, Approx.30fps, Progressive)Power Save Mode: Yes (after approx. 3 min. of inactivity)In-Camera Editing: Trimming / Red EyeCorrection / Soft Focus / Partial Color / Fisheye Lens / Cross Filter / Retro / Radial Blur / Unsharp Masking / SmileInputs and OutputsAccessory Terminal: Multi connectorAudio/Video Output(s): Yes via Mutli-Use ConnectorUSB Port(s): Yes - USB2.0 Hi-SpeedHD Output: Yes (1080i)HardwareLCD: 3.0"Clear Photo LCD Plus (230,400 pixels)1 1 Viewfinder: Yes - ElectricalLens Construction: 13 elements in 10 groups (including 1ED glass element and 1aspheric element)Microphone/Speaker: Stereo / MonoLens Type: Sony G-LensOperating ConditionsFlash Effective Range: ISO Auto: Approx. 0.3 - Approx. 9.2m (Approx. 0.98' - Approx. 30.2') (W) / Approx. 1.5 - Approx.5.1m (Approx. 4.92' - Approx. 16.7') (T), ISO3200: up to Approx.16m (Approx.52.5')(W) / Approx.10m(Approx.32.8')(T)"Flash Mode(s): Auto / Flash On / Slow Syncro / Flash OffOptics/LensFocal Length: 5.0-100.0mm35mm Equivalent: Still shots: 28-560mm / Movie 16:9: 31-620mm / Movie 4:3 :38-760Focus: 9 points / Center Weighted AF / Flexible Spot / Semi Manual / ManualAperture Range: Auto(F2.8-F8.0) / Program Auto (F2.8-F8.0) / Manual(F2.8-F8.0)Shutter Speed: Auto(2" - 1/4,000) / Program Auto (1" - 1/4,000)/ Shutter Priority(30" - 1/4000)/ Aperture Priority(8" - 1/2000) / Manual(30" - 1/4000)Exposure Compensation: Plus / Minus 2.0EV, 1 / 3EV stepSmart Zoom® Technology: 5M:Approx.26x(Total), 3M:Approx.33x(Total), VGA:Approx.108x(Total), 16:9(2M):Approx.36x(Total)Digital Zoom: Smart Zoom / Precision Digital Zoom / OffOptical Zoom: 20xMacro Mode: Macro On/Auto: W:Approx.1cm (0.03') to Infinity, T:Approx.150cm(4.92') to InfinityTotal Zoom: Approx. 40xFace Detection: Detects up to 8 Faces - with Touch Priority / Auto Priority / Child Priority / Adult PriorityPowerBattery Type: InfoLITHIUM H type 6.8VBattery Capacity: Approx. 195 minutes / Approx. 390 imagesSoftwareSupplied Software: Picture Motion Browser Vers 4.2.11 + USB Driver (Not supported by Macintosh® Operating Systems)Operating System Compatibility: Microsoft® 2000 Professional, XP Home and Professional; Macintosh® OS 9.1/9.2/OS X (10.1-10.5)ProcessorBionz™ Engine: YesControlISO: Auto / 125 / 200 / 400 / 800 / 1600 / 3200DimensionsWeight: Approx. 1lb 1.8oz. (504g) - With battery and Memory Stick media.Measurements: W x H x D: 114.5mm x 82.8mm x 91.8mm (4 5/8" x 3 3/8" x 3 5/8")Service and Warranty InformationLimited Warranty Term: Limited 1 Year Parts & LaborSupplied AccessoriesRechargeable Battery - NP-FH50Battery Charger - BC-VH1Multi Connector Cable - USB, AVPower CordShoulder strapLens CapLens Cap StrapHDMI AdaptorCD-ROM SoftwareNote: No Memory Stick PRO Duo™ Media or adaptors are included.Optional AccessoriesGPS Unit Kit (GPS-CS1KAMemory Stick PRO Duo™ Media (MS-MT2G)Memory Stick PRO Duo™ Media (MS-MT4G)Memory Stick PRO Duo™ Media (MS-MT8G)Memory Stick PRO Duo™ Media (MS-MT16G)Memory Stick Duo™ Adaptor (MSAC-M2)Memory Stick Duo™ USB Adaptor (MSAC-US40)Color: BlackUPC Code: 027*********1.Viewable area, measured diagonallypatible BRAVIA® HDTV, and component cable (sold separately) required for PhotoTV HD viewing. Specifications of the BRAVIA HDTV shown vary according to market region.3.Four preset music tracks stored in internal memory. Imported music tracks can be up to five minutes long. When using Music Transfer to download music, tracks longer than five minutes will be reduced to five minutes when uploading to the Cyber-shot® camera.4.Requires Windows 2000 Professional SP4, Windows XP SP2, or Windows Vista. Not supported by Mac OS.5.HD Viewing requires an HD output adapter cable (VMC-MHC2), sold separately.6.Maximum of 29 minutes continuous recording per video clips, limited to available capacity on storage media.7.Under average conditions; when fully charged, actual results may vary based on camera settings and conditions of use.8.Requires BRAVIA® Sync™ feature in each product. Please refer to BRAVIA and/or Remote owner’s manual to determine compatibility. 11.For uploading movies to Internet sharing sites, movies can be converted to SD image quality with Picture Motion Browser, or record in VGA resolution (640 x 480, 3Mbps). © 2009 Sony Electronics Inc. All rights reserved. Reproduction in whole or in part without written permission is prohibited. Sony, Cyber-shot, Xtra Fine LCD, BIONZ, Smile Shutter, Optical Steadyshot, Memory Stick PRO Duo, HDNA, Super HAD, Stamina, and the Sony, Cyber-shot, SteadyShot, Smile Shutter, Face Detection, BIONZ, and HDNA logos are trademarks of Sony. All other trademarks are trademarks of their respective owners. Non-metric weights and measurements are approximate and may vary.。

Hu-1H uEnvironmental/Process Air Transmitters RH and Temperature with Dew Point or Pressure Outputs U 316 SS HousingU ±1% RH AccuracyU ±0.5°C (1.0°F) Temperature AccuracyU H igh Temperature[120°C (248°F)]U R emovable StainlessSteel Sensor Cap U RS232 StandardU A djustable ¾ NPTFitting The HX80A Series is a family of humidity probes that offer a variety of measurement parameters with precision accuracy: relative humidity and temperature, with dew point or pressure. The probe is easily adaptable for most applications via a 3⁄4 NPT fitting that can beadjusted to any desired position, including high temperature and high pressure conditions. This remote type transmitter comes standard with a 1.8 m (6') cable and is ideally suited for many different applications such as environmental chambers, compressed air, and industrial applications. Models offer a stainless steel probe with a removable sinter stainless steel filter and RS232 (which allows for reading of data, scaling output, and for HX86A type units, changing the digital display and setting the alarms). All models have 3 outputs, with output 1 scaled for 0 to 100% RH, output 2 scaled for -20 to 120°C (-4 to 248°F), and output 3 determined by the model number. Output 3 for HX85A and HX86A is -60 to 40°C (-76 to 104°F) dew point, forHX85BA and HX86BA is 750 to 1100 mb, and for HX85PAand HX86PA is 0 to 200 psia. RH measurement range is 5 to 95% with an accuracy of ±1%. temperature accuracy is ±0.5°C (33°F).HX85A (probe only) models (HX85A, HX85BA, HX85PA) offer 0 to 10V signals on the outputs via a 1.8 m (6') cable. The HX86A models (HX86A, HX86BA,HX86PA) include a display box attached to the end of the cable from the probe, and offers a 2 line digital display, 2 alarms, three 4 to 20 mA output signals, and an RS232 serial output.SPECIFICATIONS RH Accuracy: ±1% RH RH Measurement Range: 5 to 95%Time Constant: <15 sec, air flow dependent (for 66.6% response)Temp Accuracy: ±0.5ºC (1.0°F)Temp Measurement Range: -20 to 120ºC (-4 to 248ºF) Pressure Rating: 317 kg (700 lb) (47.6 bar) max Serial Output: RS232C (bi-directional) to DTE device, 19.2 kilo baud, 8 bits data, 1 stop bit, no parity Power Requirements: 18 to 30 Vdcunregulated, 50 mA max HX85A shown smaller than actual size.HX86AHu-2Sensor Dimensions: robe: 19 Dia. x 203 mm (3⁄4 x 8") Cable Length: 1.8 m (6')Filter: Sinter stainless steel (removable and cleanable)Probe Material: Stainless steelFitting: Adjustable ¾ NPTWeight: 0.9 kg (2 lb)Display Box (HX86A, HX86BA, HX86PA Only): Dimensions: 130 x 94 x 56 mm (5.1 x 3.7 x 2.2") Mounting Centers: 115 x 79 mm (4.52 x 3.11") Digital Display: LCD, 2-line Electrical Analog Outputs (HX85A, HX85BA, HX85PA Only):0 to 10 Vdc (x3) @ 10 mA max Electrical Outputs (HX86A, HX86BA, HX86PA Only): Analog Outputs: 4 to 20 mA (x3) into 500 Ω max Come complete with operator’s manual (on CD) and NIST certificate.Ordering Example: HX85A, RH/air temperature/dew point transmitter with 0 to 10 Vdc outputs, and PSR-24S, regulated power supply90 to 264 Vac input with 24 Vdc output.Alarm Relay (x2): Form A (SPST , NO) rated at 3 A/250 Vac Barometric Pressure (HX85BA, HX86BA Only): Range*: 750 to 1100 mb Accuracy: ±5 mb * Although the unit is scaled 750 to 1100 mb, the unit actual measurement range is 10 to 1100 mb and can be reprogrammed in the field if the range needs to be expanded. High Pressure (HX85PA, HX86PA Only): Range: 0 to 200 psia Accuracy: ±0.75 psi。

SupportHave any questions?Feel free to get in touch https:///support/1.About the Vortex81.1Overview1.2Part Numbers1.3Warnings1.4Compliance Notes2.Getting started2.1What’s in the Box3.Water and Temperature 3.1Water3.2Temperature4.Transport and Safety 4.1Yoke Assembly4.2Rigging4.3Filter Rails4.4Installing a Dome4.5Installing a Honeycomb4.6Installing a Diffuser5.Controls5.1Controlling the Vortex85.2On-board Keypad and Display5.3Introducing CreamOS5.4CreamOS Home Screen5.5CreamOS Colour Mode5.6CreamOS Effects Mode5.6.1Effects Off5.6.2Candle&Fire5.6.3Emergency5.6.4Television5.6.5Party5.6.6Pulse5.6.7Paparazzi5.6.8Colour Cycle5.6.9Strobe5.6.10Random5.6.11Dual Level5.6.12Sync Flash5.6.13Flash Frames5.6.14Calibrate Sync5.21Notifications Tray/Status Bar5.22User Presets5.23Storing a User Preset5.24Restoring a User Preset5.25Clearing a User Presets5.26Clear All User Presets5.27Menu Functions6.Connectivity6.1Best Of Class Connectivity6.2Wired DMX Control6.3Wireless DMX Control6.4Streaming ACN(sACN)6.5Wired Remote Dimmer6.6Link Multiple Vortex8Fixtures6.7Firmware Updates Via USB7.Camera Sync7.1Syncing to Cameras7.2Setting up Camera Syncing with Sync/Genlock Input using the Flashbandit7.3Setting up Camera Syncing with Sync/Genlock Output using the Accessory BNC Cable7.4Syncing Multiple Units7.5Calibrate Sync7.6Shooting While Calibrated7.7External Effects Triggering8.Maintenance8.1Vortex8Fuse9.Power9.1Running from Batteries9.2Setting a Power Limit9.3Pinout for DC Power connector on Vortex810.Specifications10.1Specs for the Accessory Port Pinout10.2Specs for the Vortex810.3Warranty10.4SupportTable of Contents1.1OverviewThe Vortex8is a versatile2x1RGBW system with a CCT range from2200K to15000K that can be used as a hard punch light to bounce or push through diffusion,or as a creamy soft light with the Creamsource Dome or DoPchoice Snapbag.Effects and colour gels are built into the latest CreamOS architecture in addition to a range of new features wrapped into an intuitive user interface.Unpredictable weather and messy effects machines are no longer a worry for the lighting department where the Vortex is in place.The Vortex8is IP65 water resistant and sealed for the ultimate security and efficiency.Rain,snow and dust wont hold the Vortex8back.Connectivity to the Vortex8is well up to date with LumenRadio TimoTwo built in,Ethernet,Bluetooth,5pin DMX,Wifi,USB type A and Creamsource Accessory port.Interaction between Vortex8and various third party instruments and protocols are endless opening various wired and wireless control options.We are geeks for high quality and precision engineering,and loads of our geekiness has spilled into the Vortex Series.Built with elegance and durability in mind the aluminium machining and technopolymer infusion has allowed us to achieve our goals.Containment and simplicity is also achieved in this design,with the PSU as well as the antennas integrated into the head.We stand by our users offering5years Warranty when you register your product.Go to for more information.Vortex8in actionIMPORTANT -Only power Vortex with the supplied PowerCon AC cable.Some third-party cables are not rated for use in wet e etherCON TOP connector only for preventing water from damaging ethernet ports.Vortex8is rated IP65.Vortex8must NOT be submerged in water.Heavy -Vortex8weighs 13.7kg/30lbs.Lift with care.Fixture produces intense light.To prevent eye damage,do not stare directly at the light beam.Ensure that the Vortex8is clear of any obstructions in any direction with a minimum distance of 45cm/18”.Not intended for permanent outdoor use.Temporary outdoor use only.This product is intended for professional use and may only be operated by qualified persons.Do not cover the ventilation slots on the side and rear of the Vortex8.Airflow is required for cooling and operation.Inspect the power cable for damage prior to operation.Always ensure that the fixture is earthed electrically.The fixture may become hot during operation.Maximum Surface Temperature Tc =70°C.Not for Residential Use.To avoid corrosion and damage to the unit,remove power and clean with fresh soapy water after exposure to salty environments like beach locations.If using the Vortex8near water or in the rain,it is recommended to use an earth leakage circuit breaker (RCD or GFI)to protect the user and the device.If a fixture is dropped,please carefully inspect for damage.If unsure of the damage status,please remove power from the unit before touching or moving it,and seek professional service help.Exposure of the unit to high levels of UV for prolonged periods may cause the Technopolymer to degrade over time.Please inspect for weather related cracking periodically and seek professional service help if visible cracks are found.Please take care to check the fixture,connectors,and cables for signs of damage,abrasion wear,cracks,and loose screws etc prior to use.Water ingress into a damaged product may produce a shock hazard for the operator,causing injury or death.Do not open or disassemble the fixture under any circumstances,doing so voids warranty and may cause harm to you if powered.1.3Warnings1.4Compliance NotesThis device complies with Part 15of the FCC Rules.Operation is subject to the following two conditions:(1)This device may not cause harmful interference,and (2)This device must accept any interference received,including interference that may cause undesired operation.Certifications:CE,FCC,RCMPlease make sure discarded electrical waste is properly recycled to reduce environmental impact.Please use a separate collection facilityor contact the supplier from which this fixture was purchased.Vortex8YokeAC PowerCON CableT30Torx Key2.1What’s in the BoxVortex8shipswith the following items included in the box.2.Getting started12343.1WaterThe IP65rating of the Vortex8fixture means it can survive low pressure water jets in all directions,but not full submersion .It also means that it has a high resistance to dust and dirt.Precautions are advised.3.2TemperatureThe Vortex8is a high powered lighting fixture and will get quite hot during operation,especially on the aluminium chassis due to heat dissipation.Care must be taken when handling the Vortex8.•The maximum surface temperature of the lamp head will be 60°C/140°F,when operated in an ambient temperature of 25°C/77°F•Maximum ambient temperature for normal operation is 40°C/104°F.3.Water and TemperatureThe supplied PowerCon cable must be used when the Vortex8is exposed to water.Not all PowerCon cables are water resistant and can be an electrical hazard.4.1Yoke AssemblyThe Vortex8ships with a quick release yoke system that is assembled using a T30Torx tool provided.The standard yoke allows for mounting to a combo stand with a standard baby pin receiver.Included parts.Use the hex key to fix yoke arms to base.Repeat on the other side.Adjust until finger tight,do not over tighten.1243RIGGING POINT4.3Filter RailsThere are various accessories that are available for V8that can slide into the front two accessory rails.Ega standard diffuser and a honeycomb grid.Accessories slide into the rail system and lock securely with unique lock and latch system.The filter rail slot has a unique locking mechanismthat locks the initial filter in while allowing secondfilter to be inserted without unlocking.Push top latch down to engage the lock.Push gold button to release to unlock.Latch in unlock position.13244.4Installing a DomeInstalling the Dome the Vortex8widens the native 20°beam angle.This modifier softens the source and reduces shadowing.Install the Dome into the safety filter rail as per steps above in the “Rails Filter”section.Slide the dome into the first filter rail.Push top latch down to engage the lock on each side.4.5Installing a HoneycombThe honeycomb reduces the beam angle and stops ambient spill of light.This works great in with thestandard diffuser in the second slot.Slide the honeycomb into the first filter rail.Push top latch down to engage the lock on each side.4.6Installing a DiffuserThe standard diffuser softens the native hard light and widens the beam angle.This modifier works wellinconjunction with the dome and the honecomb.Slide the diffuser into the first filter rail.Push top latch down to engage the lock on each side.5.1There are 5.21and5.3Introducing CreamOSCreamOS is the all new operating system based on architecture that is robust and expandable.CreamOS continues to evolve with easy access and a user friendly interface.CreamOS is driven by the following screens:Colour Mode Effects ModeHome screen Settings screenVisit /support for the latest version of CreamOS.5.4CreamOS Home ScreenControl parameters and access the functions from theCurrent modeSelected parameter tileSelected colour mode Colour mode description CCTXYCCT RGBWHSVGELSCCT XYRGBWCCT HSVCCT GELS5.5CreamOS Colour ModeEasily switch Colour modes from this screen.For more informationEffects Off Dual LevelCalibrate SyncSync FlashRandomFlash FramesTelevision Paparazzi Candle &Fire Party Colour Cycle EmergencyPulseStrobe5.21Notifications Tray /Status BarThe notification tray in the top right corner will display status Battery Battery Source Battery Source Fan Speed Calibrated LAN Fan Speed Dimming CRMX Linked Fan Speed Dimming CRMX Disabled Fan Paused Dimming5.23Storing a User Preset1.Select an Effect or Colour and adjust the parameters to the desired result.2.Select the User Preset from the Home screen or Settings menu.3.Choose an empty slot and press Select to store it to that slot.A dialogue message will appear to show it has been stored.5.24Restoring a User Preset1.Go to the User Preset menu.2.Scroll to a slot with the stored User Preset.3.Press Select to restore that User Preset.A dialogue will inform you that it has been successfully restored.5.25Clearing a User Presets1.Go to the User Preset menu.2.Scroll to a slot with the stored User Preset.3.Press and hold down Select button.A dialogue will show to confirm your choice.5.26Clear All User Presets1.Go to the User Preset Options menu.2.Select Clear All Preset.3.Select this and a dialogue will show to confirm your choice.6.1Best Of Class ConnectivityVortex8is equiped with a wide range of connectivity Order of priority for DMX communications:Wired DMXDMX 48V DC powerPower InputWorldwide ACSet correct frame rate and format on the Lockit box (see user manual for device).This should match theframe rate and format you intend to shoot at.Plug the BNC-T adapterinto the SYNC/WORDCLOCK output of the Lockit box.Plug Flashbandit adapterinto the Creamsource Accessory adaptor.Plug the Creamsource Accessory adaptor into Accessories input of the Vortex8.Connect the Flashbandit to the Lockit Box using coaxial cable –a blue light on Flashbandit should flash indicating valid signal.Once sync is established,a green bar will be highlighted on the top of the status bar of the Vortex8indicating the device is synchronised.The frame rate will also be displayed beneath the status bar.Calibrate using the Flashbandit (see 7.5Calibrate Sync for details).Connect the camera GENLOCK input to the Lockit box with the coaxial cable.Follow the camerainstructions for setting this up.12456783123455627.2Setting up Camera Syncing with Sync/Genlock Input using the FlashbanditUse the Flashbandit (CS-SYNC)to setup cameras that requires a sync generator.7.3Setting up Camera Syncing with Sync/Genlock Output using the Accessory BNC CableUse the Creamsource Accessory BNC Cable (CSV-ACC-BNC)to setup cameras that are capable outputting a sync signal.Plug the Creamsource Accessory to BNC Cable directly into the BNC SYNC/AUX port of the camera.Plug the other end of the Creamsource Accessory to BNC Cable to the Accessory Input port of the Vortex8.Setup the camera to output the sync signal (refer to the user manual for device).Once sync is established,a green bar will be highlighted on the top of the status bar of the Vortex8indicating the device is synchronised.The frame rate will also be displayed beneath the status bar.Calibrate the Vortex8(see 7.5Calibrate Sync for details).123457798Camera Monitor2Select Effects>Calibrate Sync.The fixture will start toflash at the locked framerate(see5.20Calibrate Syncfor more details on these settings).4The Vortex8is now calibrated.It can now be set to desired effect mode(Normal,Strobe etc)E.g.Select Effects>Flash Frames.7.6Shooting While CalibratedOnce the Creamsource has been calibrated,any of the modes may be used without the possibility of causing torn frames.The remote dimmer unit or DMX control can also be used safely.If the framerate,shutter angle or the phase of the camera shutter is adjusted,then you will need to re-calibrate.7.7External Effects TriggeringYou can use an external pulse to trigger the Sync Flash and Dual Level effects.This input is on the Accessory Connector,see Accessory pinout for more information.•The Rising pulse edge triggers the effect,and is the same as pressing the FLASH button in.•The Falling pulse edge is the same as releasing the FLASH button.•The input level can be inverted by selected'Invert Input Level'from the Advanced>Sync Options menu.NOTE:An input voltage from5V–24V can be used for trigger signal.The input impedance is150kΩ.8.Maintenance8.1Vortex8FuseThe Vortex8has an internal fuse and is not user serviceable.Please contact your nearest authorised repair centre for it to be replaced.Require help finding your nearest authorised repair centre?Feel free to get in touch.https:///supportInternal fuse is only for48V DC,not AC input.Acceptable Fuses:Bel Fuse Inc.0ADKC9200-BELittelfuse Inc.0215020.MXP9.3Pinout for DC Power connector on Vortex8Choose a4core cable of>17AWG(1.0mm2)and wire all4pins.For a ready-made battery cable with3Pin XLR connector(Pin1:-ve,Pin2:+ve)see Creamsource Part number: CS-PWR-5M-XLR3.Part Number Connector Manufacturer Part NumberCSV-8Vortex8Ecomate4Pin Female Amphenol C01620D00311010Pin Wire ToE-Ve1-Ve2+Ve3+Ve10.1Specs for the Accessory Port PinoutConnector Type:Weipu Socket7PinMating Plug:Weipu Plug7Pin SF1210/P7IIPin Description1Sync/Trigger Input+Ve(5-24V Input,referenced to GND) 2DMX Data(-Ve)3DMX Data(+Ve)456GND,Ground Reference7+12V Output,200mA maximum10.2Specs for the Vortex8Aluminium/TechnopolymerRGBW LEDCCT:2200-15000K,PLUS/MINUS GREEN, HUE/SATURATION,XY,GELS,DIRECT RGBW,EFFECTSTypical95Typical9520°(Half Peak Angle)360°3200K:68,200lx/6,340fc@1m/3.3ft26,200lx/2,430fc@2m/6.6ft12,700lx/1,180fc@3m/9.8ft7,400lx/690fc@4m/13.1ft4,800lx/450fc@5m/19.4ft3,400lx/320fc@6m/19.7ft5600K:73,500lx/6,830fc@1m/3.3ft28,600lx/2,660fc@2m/6.6ft13,900lx/1,290fc@3m/9.8ft8,000lx/740fc@4m/13.1ft5,200lx/480fc@5m/19.4ft3,700lx/340fc@6m/19.7ft8x3/8”Threaded Insert Rigging Points Removable quick release yoke2Filter Rails for Secondary Lenses, Diffusers,AccessoriesHigh Precision Digital Magnetic Encoder, Backlit Keypad,Colour LCD Display0-100%with High Resolution,Super-Smooth Low End Mode Over5000fps Flicker Free in High Speed ModeSync Input for Triggering and Syncing to Camera Shutter40°CLow noise variable speed fans50,000hrs(L70)100-240V AC,50/60Hz,Max6.6A,660W. Neutrik PowerConTrue connector48V DC,Max13.75A,Can run at100% brightness on DC inputIP6515.9kg/35lb(Excluding Yoke)1.93kg/4.2lb(Yoke weight)690x380x121mm/27.2”x15”x4.8”(Excluding Yoke)831x551x164mm/32.7”x21.7”x6.4”(Including Yoke)3Years on Fixtures,12Months on Accessories(5Years registered)CE,RCM,FCC.Pending:ETCOn-Board Interface,DMX via standard5-pin XLR connectors,Wired Remote Control Accessory,Integrated Lumen radio Timo Two with Bluetooth,Ethernet,USB Type A Vortex8650W Colour,Yoke,Power cable, Flat diffuserK-CSV-8-ESS10.3WarrantyWe stand by our quality,to learn more about Warranty Terms and Conditions,please visit: https:///5-year-warranty10.4SupportHave any questions?Feel free to get in touchhttps:///supportCreamsource2/49Carrington Road Marrickville,NSW2204AUSTRALIA。

Data SheetSensor: IRA-S210ST01 Lens: IML-0685 / IML-0688Attention:Sensor : IRA-S210ST01 Lens : IML-0685/0688Pyro Electric Infrared Sensor Fresnel LensOverviewSensorPyroelectric infrared sensors detect infrared rays using the pyroelectric effect of pyroelectric ceramics, a kind of piezoelectric ceramics. IRA series offers pyroelectric infrared sensor that deliver high sensitivity and reliable performance made possible by Murata's ceramic technology and Hybrid IC technique expertise. Used mainly in security equipment. IRA-E series includes high quality and reliable performance products by improving themanufacturing process. Combining performance with low costs, the IRA-S series makes it easier to use pyroelectric infrared sensor in security application and general consumer equipment.LensLens series offer fresnel lens for Murata pyroelectric infrared sensor.Features● Excellent S/N ● Low voltage operation availableApplications● Intrusion Detectors ●Lighting AutomationPlease select IML-0685 or IML-0688 depend on your application and target detection areaTABLE OF CONTENTCAUTION5.1 Limitation of Applications Attention:Attention:2. Specifications and Measurement Direction2.1 Sensor2.1 1 Dimension of infrared ray receiving electrode (For reference)2.1 2 Internal circuit diagramFig.2 Circuit diagram2.1 3 Basic (rated) operation conditionsTable.1 Operation conditions2.1 4 Performances (Unless otherwise noted 25︒C ±3°C)Table.2 Performance of electric specificationsFig.1 Top viewDrain Source GNDAttention:2.1 5 Measurement Direction Note1 : Test system of ResponsivityFig.3 Test systemNote1 : Test circuit for White NoiseFig.4 Test circuit for White noiseNote3 : Test circuit for Source VoltageFig.5 Test circuit for source voltageLock-in Amp. (NF LI5640) 1HzAttention:2.2 Lens2.2 1 Basic CharacteristicTable.3 Basic Characteristec2.2 2 TransmittanceFig.6 Transmittance2.3 Selection Guide of LensPlease select IML-0685 or IML-0688 depend on your application and target detection area. 2.3.1 IML-0685For Wall mount type (Inline type)This lens is good at detecting the motion across target area. 2.3.2 IML-0685For Ceiling type and Wall mount type (Round type.This lens has more optical segments compared with IML-0685.8001000120014001600180020002500300035004000cm-1Wave number2.5μ3.04.05.06.07.08.010.012.0mWave length20406080100%600020.0Attention:2.3.3 Detection areaIML-0685*Assembled with Murata sensor IRA-S210ST01.Combined lens tab A to sensor tabFig.7 Horizontal detection area0m 6m6mAttention:IML-0688*Assembled with Murata sensor IRA-S210ST01.Combined lens tab A to sensor tabFig.12 Assembled with sensor0m3m 3mFig.10 Horizontal detection areaFig.11 Vertical detection areaAttention:3. Dimension3.1 Sensor : IRA-S210ST01Fig.16 Field of viewNotes)● Nickel-plated on terminal. However the terminal cut ● C 1 and C 2 are specified on 1.2mm from base ● I is specified on baseXYFig.15 Bottom viewXZBaseFig.14 Side viewPyro-Element(45deg .)(45deg .)Fig.13 Top viewTabC 2X YAttention:3.2 Lens : IML-0685 / IML-0688Please set the direction of the tab on the fresnel lens to the tab on the sensor.To bring pyro-Element into the focus of fresnel lens, Please push the sensor until the step inside the fresnel lens.Please design the housing that the sensor does not receive infrared ray through the area shown as diagram in Figure A.Fig.17 Dimension of Lens Unit ：mmGeneral tolerance ：±0.2Fig.18 An example of a design of the housingPyro-Elementstray light degreeAttention:4. Packing4.1 Sensor100 pieces sensors shall be packed in a unit box (box size: LWD （mm ） 104x75x47) as shown in Fig.19Fig. 19 Packing configuration of Sensor 4.2 Lens100 pieces lenses shall be packed in a plastic bag as shown in Fig.20.5. Caution5.1 Limitation of ApplicationsPlease do not use in the applications listed below which require a high reliability to prevent the defects which might cause a damage to the Peoples’ life and/or property. 1) Aircraft equipment 2) Aerospace equipment 3) Undersea equipment4) Power plant control equipment 5) Medical equipment6) Transportation equipment (trains, ships, etc.) 7) Traffic signal equipment8) Disaster prevention / crime prevention equipment 9) Data-processing equipment10) Military equipment (regardless of directly/indirectly) 11) Security device/system12) Outside-usage, in which the sensor is exposed to splashes or dustsApplication of similar complexity and/or reliability requirement to the applications listed in the abovLens 100pcsFig.20 Packing configuration of Lens5.2 Fail-SafePlease make sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product5.3 Notice in Design5.3 1 Sensor1) In the case of outdoor use, suitable Optical Filter and water and humidity proof structure should beapplied.2) To prevent failure or malfunction, Please use a stabilized power supply.3) Please avoid using the sensor in the following conditions because it may cause failure ormalfunction ;a) In such a fluid as water, alcohol etc. corrosive gas (SO2, Cl2, NO X etc.) or sea breeze.b) In high humidity.c) In a place exposed directly to sunlight or headlight of automobile.d) In a place exposed to rapid ambient temperature change.e) In a place exposed directly to blow from air-conditioner or heater.f) In a place exposed to strong vibration.g) In a place exposed to strong electromagnetic field.h) In such a place where infrared ray is shaded.i) In such a place are charge field and static electricity field.j) In any other place similar to the above (a) through (i).5.3 2 LensPlease avoid using the fresnel lens in the following conditions because it may cause failure ormalfunction ;a) in such a fluid as water, alcohol etc. corrosive gas (S02,Cl2,NO X etc.) or sea breeze.b) in high humidity.c) in a place exposed directly to sun light or headlight of automobile.d) in a place exposed directly to blow from air-conditioner or heater.e) in such a place where infrared ray is shaded.f) in any other place similar to the above (a) through (e).Attention:5.4 Notice in handling and storage5.4.1 Sensor1) Optical Filter of sensor should not be scratched or soiled.2) Strong shock should be avoided.3) It may malfunction under electrostatics and electromagnetic field.Please use it after enough evaluating.4) Electrostatics and strong electromagnetic field should be avoided.5) Sensor should be kept on conductive sponge6) High temperature, high humidity, fluid as water or alcohol etc., corrosive gas ( SO2, Cl2, NO X etc.)and sea breeze should be avoided.7) Store the products where the temperature and relative humidity do not exceed -10 to 40 degreescentigrade, and 15 to 85%RH. Use the products within 6 months after receiving. Check the terminalsolderability before use if the product has been stored for more than 6 months.8) The terminal cut section does not have plating.So there is possibility to rust on cutting section depending on environment.5.4 2 Lens5.4.1 Lens1) Optical filter of sensor should not be scratched or soiled.2) Strong shock should be avoided.3) High temperature, high humidity, fluid as water or alcohol etc., corrosive gas (S02,Cl2,NO X etc.) andsea breeze should be avoided.5.5 Notice in mounting (Sensor)1) Please perform the soldering of the terminal with an iron point solder.2) Please mount the soldering of the terminal as quick as possible. Specifically, please go in the rangeof follows.Table.4 Soldering condition3) Please use the flux which has a water-soluble thing less than chlorine content 0.2% by weight.4) Please completely remove the flux after the soldering. When you are insufficient, it causes themalfunction.*Please follow soldering conditions described in the specification.This product can permanently stop operating if the piezoelectric (pyro electric) characteristicis decreased due to excessive heatingAttention:5.6 Other1) Please make sure that your product has been evaluated in view of your specifications with ourproduct being mounted to your product.2) You are requested not to use our product deviating from this product specification.3) We consider it not appropriate to include any terms and conditions with regard to the businesstransaction in the product specifications, drawings or other technical documents. Therefore, ifyour technical documents as above include such terms and conditions such as warranty clause, product liability clause, intellectual property infringement liability clause, or export controlclause, they will be deemed to be invalid.Attention:。