外文翻译--城市道路线位选择之要点
- 格式:doc
- 大小:50.50 KB
- 文档页数:10
4.2表示同一条道路不同路段,但位于通名前的属性词应当意译,使用英语
4.2.2该类属性词中的数词“一、二、三、四”,翻译时置于整个路名之后。
书面形式中如需缩写,该类属性词的缩写形式也置于整个路名之后,并用括弧标
4.2.3道路名称中如同时使用方位词和数词,翻译时,方位词置于整个路名之前、数词置于整个路名之后。
书面形式中如需缩写,两个属性词作为一个整体,置于整个路名之后,并用括弧标注;其中,方位词缩写使用相应的英语字母,数
5.同名道路整治过程中添加的前缀部分,中文必须标示,英文不标示。
如:。
1引言道路选线阶段是市政道路设计过程中的关键一步,在以往线位比选时,存在着分析不全面、认识程度不够、技术经济不合理等问题,导致道路建设没有达到预期目标,对周边环境产生严重影响,制约了城市的发展进程,所以,必须改变传统设计理念,在符合城市总体规划的基础上,明确线位比选顺序和方法,兼顾技术指标、经济指标、环境指标,通过建立综合评价系统进行客观分析和科学选择。
2工程简介汕头市海滨路东延二期及滨海空间新建工程位于汕头华侨试验区珠港新城。
根据珠港新城控制性详细规划,珠港新城规划构筑“一体两翼三轴三组团”的空间结构,依托滨海岸线布局贯穿东西向的滨海都市休闲轴,建设海滨路东延二期及滨海空间新建工程就是其中的重要组成部分。
本文针对本工程道路线位比选和关键节点方案制订展开探讨。
3市政道路线位比选技术方案分析3.1线位沿线制约因素影响道路线位比选的因素有很多,包括自然条件、外部环境、工程经济、设计规范等方面。
除了对选线约束条件进行宏观分析,还应该对选线影响因素进行量化分析,从选线基本原则出发,结合实际情况和经验,不断优化设计方案,做出最佳选择。
除了常规制约因素外,本工程线位沿线突出制约因素主要有临近海域、现状防潮堤、沈海高速(汕头海湾大桥)、现状建筑(如污水处理厂)、起点和终点处相接道路等,必须明确这些工程设施的位置、功能、状态等相关情况,分析制约因素影响程度,并以此作为线位比选的重要依据[1]。
3.2线位比选技术方案道路线位比选需要分步分段进行。
首先,明确路线基本走向;其次,确定路线具体位置,包括重要的线路中间控制点以【作者简介】陈晖(1981~),男,上海人,高级工程师,从事市政工程道路设计与研究。
市政道路线位比选与关键节点方案分析Comparison and Selection of Municipal Road Alignment and Analysisof Key Node Schemes陈晖(同济大学建筑设计研究院(集团)有限公司,上海200092)CHEN Hui(Tongji University Architectural Design and Research Institute (Group)Co.Ltd.,Shanghai 200092,China)【摘要】对市政道路线位比选与关键节点方案进行分析,以实际工程案例为抓手,明确主要制约因素,采用科学选线方法,从全面布局到逐段规划,实现关键节点的精确设计,在选出最优化路径的同时,能够充分利用现有资源,满足多元化目标需求。
公共场所双语标识英文译法第一部分:道路交通细则警告提示信息警告提示信息的翻译应按照国际通用惯例,遵循英语语言习惯,如:爬坡车道Steep Grade。
地名通名一般(基本)规定地名通名通常采用英文直接翻译,英文单词首字母大写,其余小写。
街Avenue (Ave)仅用于长安街 CHANG’AN Ave,平安大街 PING’AN Ave 和两广路LIANGGUANG Ave。
街、大街用Street(St),如隆福寺街LONGFUSI St,惠新东街HUIXIN East St;西单北大街XIDAN North St,菜市口大街CAISHIKOU St。
小街、条、巷、夹道一般情况下用Alley,当路宽达到一定规模时可选用St,如东直门北小街DONGZHIMEN North Alley,横一条HENGYITIAO Alley,东四十条DONGSISHITIAO St,后海夹道HOUHAI Alley;斜街译为Byway。
路路用Road(Rd),如白云路BAIYUN Rd。
辅路用Side Road(Side Rd),如京石高速辅路JINGSHI Expwy Side Rd。
高速公路用Expressway(Expwy),如京津塘高速JINGJINTANG Expwy。
公路用 Highway,如京兰路 JINGLAN Highway。
胡同胡同的译法形式为Hutong,如前章胡同QIANZHANG Hutong。
立交桥立交桥的英文译法全部采用Bridge,如京广桥JINGGUANG Bridge,国贸桥GUOMAO Bridge。
其他通名的译法里、区、园均用汉语拼音,如芳园北里FANGYUAN BEILI,芳城园二区FANGCHENGYUAN ERQU,惠谷根园HUIGUGENYUAN。
地名专名地名专名通常采用汉语拼音标注,汉语拼音全部大写。
专用名词为路名专名时,专名采用汉语拼音,如天坛东路TIANTAN East Rd,白云观街BAIYUNGUAN St;但指路标志(或旅游区标志)指向内容为特定场所(而非周边道路)时则采用英文,如天坛Temple of Heaven。
道路平面选线原则引言道路平面选线是指在规划和设计道路时,选择合适的位置和线路走向,以满足交通需求和确保道路平面的安全性、通行性和经济性。
选线原则是制定选线策略和方案的基础,对于道路规划和设计非常重要。
本文将对道路平面选线原则进行全面、详细、完整和深入的探讨。
拟定选线原则在进行道路平面选线时,需要考虑多个因素,如交通流量、道路功能、地质地貌、环境保护、社会经济和财务等。
根据多年的理论研究和工程实践,可以得出以下几个拟定选线原则:1. 交通需求原则根据道路的功能需求,选择适当的路线走向和位置。
主要考虑以下几个方面: - 交通流量:根据预测交通量和未来的交通需求,选择适当的道路走向和位置,保证道路的承载能力和通行效率。
- 交通安全:避免选择存在交通事故多发点和高风险区域的线路,确保道路平面的安全性。
- 交通互通性:考虑与现有和未来的交通网络的衔接和互通,确保道路能够与其他道路和交通设施良好地连接。
2. 地质地貌和环境原则根据地质地貌和环境特征,选择适当的道路走向和位置。
主要考虑以下几个方面:- 地形条件:选择地势较为平缓、土质较好的区域,减少工程难度和成本。
- 水系和湿地:避免经过重要水系和湿地,保护水资源和生态环境。
- 自然保护区和文化遗产:避免破坏自然保护区和文化遗产,保护生态环境和历史文化遗产。
3. 社会经济和财务原则根据社会经济和财务状况,选择经济合理的道路走向和位置。
主要考虑以下几个方面: - 社会效益:选择能够满足当地和周边居民出行需求的线路,降低交通拥堵和通行成本,提高交通效率和便捷性。
- 经济投入:选择投资造价较低、运营成本较低的线路,确保道路建设和运营的经济可行性和可持续性。
- 财务可行性:结合财政资源和资金来源,制定合理的财务规划,确保道路选线方案的财务可行性。
道路平面选线的实施步骤道路平面选线的实施可以分为以下几个步骤:1. 确定规划范围明确道路选线的范围和限制条件,如涉及的地区、功能需求、环境特征等。
市政道路路线线形设计要点分析市政道路的路线线形设计是指根据道路的功能和交通需求,合理规划道路的走向、宽度、曲线形状等要素的设计。
正确的路线线形设计可以提高道路的通行能力,减少交通事故的发生,改善交通环境,提高城市的交通运输效率。
下面将对市政道路的路线线形设计的要点进行分析。
1. 城市综合规划考虑:在进行市政道路的路线线形设计之前,需要进行城市综合规划的考虑。
通过考虑城市的总体规划,道路可以更好地与周围的建筑、公共设施等相协调,形成统一的城市形象。
2. 减少交叉口:为了提高道路的通行能力,尽量减少交叉口的数量。
在路线线形设计时,可以采用控制交叉口数量、设置单向通行道路等方式来减少交叉口,提高道路通行效率。
3. 曲线的设计:曲线的设计是道路线形设计中一个重要的要素。
在市政道路的曲线设计中,需要考虑道路的流线型、车速、车流量等因素,合理设计曲线的半径和长度,确保车辆能够平稳地通过曲线。
4. 至少两条车道宽度:市政道路的路线线形设计需要考虑车辆的通行需求,一般情况下,道路应至少设置两条车道。
根据不同道路的交通需求,可以适当增加车道数量,确保道路的通行能力。
5. 路缘石的设置:在进行市政道路的路线线形设计时,需要考虑路缘石的设置。
路缘石的设置能够有效地隔离行车道与人行道,保护行人的安全,同时也可以起到美化道路环境的作用。
6. 安全设施的设置:市政道路的路线线形设计还需要考虑安全设施的设置,如交通标志、标线、信号灯等。
这些安全设施能够引导车辆和行人的通行,减少交通事故的发生。
8. 路段疏解设计:在市政道路的路线线形设计中,需要对交通繁忙的路段进行疏解设计。
通过设置匝道、环岛等交通设施,将一部分交通流量从主干道上疏导出来,缓解交通压力。
一.试验平台:ArcGIS9.2二.实验目的:了解网络分析,通过网络分析解决实际问题。
三.实验要求:通过网络分析,进行城市最近道路的选择。
四.实验数据:shapefile的点线数据。
五.实验步骤:准备:打开ArcMap,加载point.shp,和road.shp。
加入空间参考。
在Layers处右击,在下拉菜单中选择Properties,弹出Date Frame Properties对话框,将Units中的Map 和Display都设置成Meters。
然后应用,确定。
Extensions,选择Network Analyst,然后关闭Extensions。
然后在View的下拉菜单中选择Toolbar中的Network Analyst,将其加入编辑界面。
方便我们使用。
因为没有网络数据集,所以控件为不可用状态。
2.在ArcCatalog中加入Network Analyst。
打开ArcCatalog,用同1中的的方法给ArcCatalog也加入Network Analyst。
3.创建road的网络数据集。
在road.shp处右击,在下拉菜单中选择New Network Dataset。
弹出New Network Dataset的创建对话框。
根据提示来创建网络数据集。
在创建过程中,所有的都选的是NO。
之后要创建两个要素,一个是length,其单位是Meters,另一个为mint,其单位是Minutes。
然后点击“下一步”。
通过创建向导,我们把该设置的要素属性都给设置之后,我们单击“Finish”。
这样一个road的网络数据集就算完成了。
创建完成的网络数据集通过鼠标的拖动或者通过数据的加载,可以把创建的数据集加入ArcInfo。
当数据加入后,New Network自动启动。
为可编辑状态。
加载之后,可以将ArcCatalog关闭。
4.寻找最佳路径。
打开New Network的下拉菜单,选择NewClosest Facility。
中文地址英译原则2009-10-26 来源:CATTI 【大中小】我要投稿中文地址的排列顺序是由大到小,如:X国X省X市X区X路X号,而英文地址则刚好相反,是由小到大。
如上例写成英文就是:X号,X路,X区,X市,X省,X国。
掌握了这个原则,翻译起来就容易多了。
请注意:翻译人名、路名、街道名等,最好用拼音。
例如:虹口区西康南路125弄34号201室Room 201, No. 34, Lane 125, XiKang Road(South), HongKou District473004河南省南阳市中州路42号李有财Li YoucaiNo. 42,Zhongzhou Road, Nanyang City,Henan Prov. China 473004用汉语拼音字母拼写中国地名,不仅是中国的统一标准,而且是国际标准,全世界都要遵照使用。
一、专名是单音节的英译法专名是单音节,通名也是单音节,这时通名应视作专名的组成部分,先音译并与专名连写,后重复意译,分写(汉字带点的字是通名,英语的画线部分是音译;括号内为该地所在省、市、地区或县,下同)例如:1、恒山 Hengshan Mountain (山西)2、淮河 the Huaihe River (河南、安徽、江苏)二、通名专名化的英译法通名专名化主要指单音节的通名,如山、河、江、湖、海、港、峡、关、岛等,按专名处理,与专名连写,构成专名整体。
例如:1、都江堰市 Dujiangyan City (比较: the Dujiang Weir)(四川)2、绥芬河市 Suifenhe City (比较:the Suifen River)(黑龙江)三、通名是同一个汉字的多种英译法通名是单音节的同一个汉字,根据意义有多种不同英译法,在大多数情况下,这些英译词不能互相代换。
例如:1、mount:峨眉山 Mount Emei(四川峨眉)2、sea:邛海 the Qionghai Lake(四川西昌)在某些情况下,根据通名意义,不同的汉字可英译为同一个单词。
一.试验平台:ArcGIS9.2二.实验目的:了解网络分析,通过网络分析解决实际问题。
三.实验要求:通过网络分析,进行城市最近道路的选择。
四.实验数据:shapefile的点线数据。
五.实验步骤:准备:打开ArcMap,加载point.shp,和road.shp。
加入空间参考。
在Layers处右击,在下拉菜单中选择Properties,弹出Date Frame Properties对话框,将Units中的Map和Display都设置成Meters。
然后应用,确定。
Extensions,选择Network Analyst,然后关闭Extensions。
然后在View的下拉菜单中选择Toolbar中的Network Analyst,将其加入编辑界面。
方便我们使用。
因为没有网络数据集,所以控件为不可用状态。
2.在ArcCatalog中加入Network Analyst。
打开ArcCatalog,用同1中的的方法给ArcCatalog也加入Network Analyst。
3.创建road的网络数据集。
在road.shp处右击,在下拉菜单中选择New Network Dataset。
弹出New Network Dataset的创建对话框。
根据提示来创建网络数据集。
在创建过程中,所有的都选的是NO。
之后要创建两个要素,一个是length,其单位是Meters,另一个为mint,其单位是Minutes。
然后点击“下一步”。
通过创建向导,我们把该设置的要素属性都给设置之后,我们单击“Finish”。
这样一个road的网络数据集就算完成了。
创建完成的网络数据集通过鼠标的拖动或者通过数据的加载,可以把创建的数据集加入ArcInfo。
当数据加入后,New Network自动启动。
为可编辑状态。
加载之后,可以将ArcCatalog关闭。
4.寻找最佳路径。
打开New Network的下拉菜单,选择NewClosest Facility。
外文翻译--城市道路线位选择之要点Main Points of Choice of the Urban Road Line1. The overviewAs one of the products of social development and one of the main component elements of modern cities, the urban road has respect to the coordination and sustainable developme nt of cities and shows the cities’ potential of economical and cultural development. The original network of urban road needs to be programed and adjusted again , especially owning to the rapid expansion of cities and the great increase of the number of cars in recent years. The urban road is not a seperated object any more, and its development is increasingly restricted by other factors of city develpoement. Therefore, the line-bit choice should show the coordination and integration between roads and the environment. The reasonable line-bits will have a positive impact on the economy,society, environment and people’s life. On the contrary, the unreasonable line-bits will influence the surroundings of them and bring some side effects.2. The comparison and selection of line-bitsWith the increasing importance attached on such issues as sustainable develpoement, environment protection and land usage, the thinking modes of road design should be changed, from only emphasizing the cost of initial construction stage to considering the cost of both construction and operation, only the safety and interest of the users to the feelings of other residents and the public, only the visible terrain and objects on the ground to the construction conditions such as geology, historical relics and mineral resources, only the coordinative design among the roads themselves to the coordinative reseach between roads and their such surroundings as natrue, ecology, society and humanity. The comparison and selection of line-bits means that the designer, in his day-to-day job, compares the different lines in different aspects and chooses the most economical, practical,and reasonable one which also meets the country’s relevent standards and policies. However, the selection is made with the designer’s overall consideration of the economy, cultrue, environment, pedestrian, safety androad-intersection, and under the premise of not having influence on the public’s life and economic develpement.3. The main points.At present, the line selection in the design of urban road is not only a purely technical proof process of the line-bit comparison and selection, but also a process of implementing the pre-planning.At the same time,it needs the respect for natural environment,the adoption of public opinion,the prudence of demolition works and the consideration of economic interests of the parties, especially the protection for water resources and cultural relics. Only the above points having been finished, the selected road line could receive broad supports,reflect the planning intention, promote local economic development, and improve the function of urban road network.3.1. The implementation of the pre-planningThe choice of urban road lines should be based on the reasonable plan of urban land usage and urban road network.And it is necessary to consider both the urban land usage and urban road network. In recent years, with the rapid development of urban construction,the phenomenon that urban planning can not keep up with urban construction frequently appears, which also has led to many reconstruction and waste of resources. How to find a better mode of operation to minimize the losses, is the first issue worthwhile exploring in the urban construction planning. Only having the full knowlegde of pre-planning intention and understanding of the funtion of project planning, can people imlpement the planning better.3.2. Respect for natural environmentAccording to "the report on China's ecological problems ",ecological damage caused by the construction of road transportation and developing of mineral resources has become one of the main reasons for the deterioration of ecological environment, and intends to be more and more serious. General designers are accustomed to "dig roads in mountains and build bridge over waters". This has resulted in that it will take a long time for the completion of infrastructure projects,the large tracts of vegetation andOriginal topography to recover or not resume, or even resulted in a series of environmental disasters . The awareness which the designers need to establish is that road is a part of the whole environment of its location,so when we select and design the road lines,we should attach importance to the protection of and respect for the environment so as to make the environment better ,but rather damage the surroundings. Therefore, as a responsibile designer,one needs to tirelessly and repeatedly optimize the line programs.Line selection embodies respect for the natural environment at the following points:1.Take up less arable land; keep away the basic protected farmland;2.Evaluate on the basis of environment;keep away the sore piont of environment;3.Conform to the topography and geomorphology; reduce the high filling and deep digging.3.4. Prudence of demolition worksAccording to the previous experience on engineering, the problem of removal and compensation is often an important factor influencing the project advancement. Therefore, we should pay attention to the road line-bit as much as possible to avoid dense building areas and to reduce the cost of demolition and resettlementthe. When we have to demolish some buildings,we should try our best to carry on the country's resettlement subsidy policy, and we need to not only safeguard the lawful rights and interests of the demolition parties, but also guarantee the smooth progress of construction projects. "The Property Law of People's Republic of China " was put in practice on October 1, ter on, the demolition for urban road construction or land development should be considered more carefully.3.5 The consideration of economic interests of the partiesIn the process of selecting road line’s scheme, on the premise of standard meeting, if the alignment of road is bad, its investment is small; if the alignment is good, the investment is large; if the investment is small, its enforceability is poor;if the investment is large, its operability is high. All these make it difficult to set down which one is better.“The Guide for New Concept of Highway Design” which is compiled by the Ministry of Transportation has proposed to establish a design concept of “the cost of full life-cycle”,that’s to say, the road lines should be intercompared in such stages as construction, maintenance, operation and management,and both the construction cost and operating cost should be taken into account. In addition,we need to carry out the economic analysis in the feasibility study for the road’s construction,and to carry out the analysis in terms of economy and social benefits when comparing the schemes of parts of the road, so that the line-bit and its technical indicators could be settled down by its service level and the benefits for economy and society..3.6 The protection for water resourcesAt present, our country’s intensity of controlling water pollution is increasing year after year, and people have realized that the seriousness of ecological deterioration caused by water pollution. So when reservoirs, lakes and other water bodies get involved in the process of line selection, we should pay special attention to whether these water bodies are the residents’drinking water sources or not. Because the water on the pavement will cause contamination, direct discharging the above water bodies will damage the water resources and threat the lives of urban residents. Therefore,when setting down the lines,we must give priority to protecting the water resources,set them down at the lower reaches of water bodies or beside the protection line of water resources.Under some special circumstances such as having to build a bridge over the water or set down the line at the upper reaches,we should carry out especial drainage design, make the water on pavement be discharged and disposed seperately ,and arrange the preplans for the accidents caused by the hazardous chemicals,in order to ensure the water safety.3.7. The protection for cultural relicsIf there is a cultural relic in the area going to be used for road constrution or within the demolition site,we have to evaluate the level of the cultural relic according to Law of the People's Republic of China on the Protection of Cultural Relics, decidewhether adjust the line-bit or not ,because the cultrual relics can not be randomly dismantled or demolished,and appearance be destroyed. Only with the approval of relevant departments,the licensing authorities can issue the permits for construction or demolition.3.8.Other factorsIn the process of choosing the urban road lines, we may come across some other factors. On that conditon, we must considerate comprehensively and emphasize some point, and select the best line, on the premise that the project is practical, as the recommended line to advance the project .4. ConclusionThe line-bit seems simple, but in fact there are a lot of knowledge storing up in it. Not all the points mentioned above may arise in the process of choosing the urban road lines , but it is likely to encounter more problems that are more complicated.And these problems are always contradictary:if you intend to protect the water resources,the range of demolition may increase;if you try to protect the environment, the investment may raise. Therefore, after so many cpmparisions and various opinions of the natives being taken into account, setting down the final practical program is a hard and complicated process of selecting. as a responsible road designer, we must consider all these factors and choose the best and use it.城市道路线位选择之要点1、概述城市道路是社会发展的产物,是现代城市的重要组成部分,关系到一个城市的协调和可持续发展,也体现出一个城市经济、文化发展的潜力。